| Home | << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 >> [101–200] |
|
| Records | |||||
|---|---|---|---|---|---|
| Author | Xu, W.; Buelens, L.C.; Galvita, V.V.; Bogaerts, A.; Meynen, V. | ||||
| Title | Improving the performance of gliding arc plasma-catalytic dry reforming via a new post-plasma tubular catalyst bed | Type | A1 Journal Article | ||
Year  |
2024 | Publication | Journal of CO2 Utilization | Abbreviated Journal | Journal of CO2 Utilization |
| Volume | 83 | Issue | Pages | 102820 | |
| Keywords | A1 Journal Article; Dry reforming Gliding arc plasma Plasma catalytic DRM Ni-based mixed oxide Post-plasma catalysis; Plasma, laser ablation and surface modeling Antwerp (PLASMANT) ; | ||||
| Abstract | A combination of a gliding arc plasmatron (GAP) reactor and a newly designed tubular catalyst bed (N-bed) was applied to investigate the post-plasma catalytic (PPC) effect for dry reforming of methane (DRM). As comparison, a traditional plasma catalyst bed (T-bed) was also utilized. The post-plasma catalytic effect of a Ni-based mixed oxide (Ni/MO) catalyst with a thermal catalytic performance of 77% CO2 and 86% CH4 conversion at 700 ℃ was studied. Although applying the T-bed had little effect on plasma based CO2 and CH4 conversion, an increase in selectivity to H2 was obtained with a maximum value of 89% at a distance of 2 cm. However, even when only α-Al2O3 packing material was used in the N-bed configuration, compared to the plasma alone and the T-bed, an increase of the CO2 and CH4 conversion from 53% and 53% to 69% and 69% to 83% was achieved. Addition of the Ni/MO catalyst further enhanced the DRM reaction, resulting in conversions of 79% for CO2 and 91% for CH4. Hence, although no insulation nor external heating was applied to the N-bed post plasma, it provides a slightly better conversion than the thermal catalytic performance with the same catalyst, while being fully electrically driven. In addition, an enhanced CO selectivity to 96% was obtained and the energy cost was reduced from ~ 6 kJ/L (plasma alone) to 4.3 kJ/L. To our knowledge, it is the first time that a post-plasma catalytic system achieves this excellent catalytic performance for DRM without extra external heating or insulation. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-05-25 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2212-9820 | ISBN | Additional Links | ||
| Impact Factor | 7.7 | Times cited | Open Access | ||
| Notes | Wencong Xu, Vladimir V. Galvita, Annemie Bogaerts, and Vera Meynen would like to acknowledge the VLAIO Catalisti Moonshot project D2M and the VLAIO Catalisti transition project CO2PERATE (HBC.2017.0692). Lukas C. Buelens acknowledges financial support from the Fund for Scientific Research Flanders (FWO Flanders) through a postdoctoral fellowship grant 12E5623N. Vladimir V. Galvita also acknowledges a personal grant from the Research Fund of Ghent University (BOF; 01N16319). | Approved | Most recent IF: 7.7; 2024 IF: 4.292 | ||
| Call Number | PLASMANT @ plasmant @ | Serial | 9131 | ||
| Permanent link to this record | |||||
| Author | Van Gordon, K.; Ni, B.; Girod, R.; Mychinko, M.; Bevilacqua, F.; Bals, S.; Liz‐Marzán, L.M. | ||||
| Title | Single Crystal and Pentatwinned Gold Nanorods Result in Chiral Nanocrystals with Reverse Handedness | Type | A1 Journal Article | ||
| Year |
2024 | Publication | Angewandte Chemie International Edition | Abbreviated Journal | Angew Chem Int Ed |
| Volume | Issue | Pages | |||
| Keywords | A1 Journal Article; Electron Microscopy for Materials Science (EMAT) ; | ||||
| Abstract | Handedness is an essential attribute of chiral nanocrystals, having a major influence on their properties. During chemical growth, the handedness of nanocrystals is usually tuned by selecting the corresponding enantiomer of chiral molecules involved in asymmetric growth, often known as chiral inducers. We report that, even using the same chiral inducer enantiomer, the handedness of chiral gold nanocrystals can be reversed by using Au nanorod seeds with either single crystalline or pentatwinned structure. This effect holds for chiral growth induced both by amino acids and by chiral micelles. Although it was challenging to discern the morphological handedness for<italic>L</italic>‐cystine‐directed particles, even using electron tomography, both cases showed circular dichroism bands of opposite sign, with nearly mirrored chiroptical signatures for chiral micelle‐directed growth, along with quasi‐helical wrinkles of inverted handedness. These results expand the chiral growth toolbox with an effect that might be exploited to yield a host of interesting morphologies with tunable optical properties. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-05-24 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1433-7851 | ISBN | Additional Links | ||
| Impact Factor | 16.6 | Times cited | Open Access | ||
| Notes | Ana Sánchez-Iglesias is acknowledged for support in the synthesis of pentatwinned gold nanorods. The authors acknowledge financial support by the European Research Council (ERC CoG No. 815128 REALNANO to S.B.), from MCIN/AEI/10.13039/501100011033 (Grant PID2020- 117779RB-I00 to L.M.L.-M and FPI Fellowship PRE2021- 097588 to K.V.G.), and by KU Leuven (C14/22/085). This work has been funded by the European Union under Project 101131111—DELIGHT. Funding for open access charge: Universidade de Vigo/ CRUE-CISUG. | Approved | Most recent IF: 16.6; 2024 IF: 11.994 | ||
| Call Number | EMAT @ emat @ | Serial | 9129 | ||
| Permanent link to this record | |||||
| Author | Faraji, F.; Neyts, E.C.; Milošević, M.V.; Peeters, F.M. | ||||
| Title | Comment on “Misinterpretation of the Shuttleworth equation” | Type | A1 Journal ArticleUA | ||
| Year |
2024 | Publication | Scripta Materialia | Abbreviated Journal | Scripta Materialia |
| Volume | 250 | Issue | Pages | 116186 | |
| Keywords | A1 Journal ArticleUA | ||||
| Abstract | |||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-05-24 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1359-6462 | ISBN | Additional Links | ||
| Impact Factor | 6 | Times cited | Open Access | ||
| Notes | Research Foundation Flanders; | Approved | Most recent IF: 6; 2024 IF: 3.747 | ||
| Call Number | UA @ lucian @ | Serial | 9116 | ||
| Permanent link to this record | |||||
| Author | Maerivoet, S.; Tsonev, I.; Slaets, J.; Reniers, F.; Bogaerts, A. | ||||
| Title | Coupled multi-dimensional modelling of warm plasmas: Application and validation for an atmospheric pressure glow discharge in CO2/CH4/O2 | Type | A1 Journal Article | ||
| Year |
2024 | Publication | Chemical Engineering Journal | Abbreviated Journal | Chemical Engineering Journal |
| Volume | 492 | Issue | Pages | 152006 | |
| Keywords | A1 Journal Article; Plasma, laser ablation and surface modeling Antwerp (PLASMANT) ; | ||||
| Abstract | To support experimental research into gas conversion by warm plasmas, models should be developed to explain the experimental observations. These models need to describe all physical and chemical plasma properties in a coupled way. In this paper, we present a modelling approach to solve the complete set of assumed relevant equations, including gas flow, heat balance and species transport, coupled with a rather extensive chemistry set, consisting of 21 species, obtained by reduction of a more detailed chemistry set, consisting of 41 species. We apply this model to study the combined CO2 and CH4 conversion in the presence of O2, in a direct current atmospheric pressure glow discharge. Our model can predict the experimental trends, and can explain why higher O2 fractions result in higher CH4 conversion, namely due to the higher gas temperature, rather than just by additional chemical reactions. Indeed, our model predicts that when more O2 is added, the energy required to reach any set temperature (i.e., the enthalpy) drops, allowing the system to reach higher temperatures with similar amounts of energy. This is in turn related to the higher H2O fraction and lower H2 fraction formed in the plasma, as demonstrated by our model. Altogether, our new self-consistent model can capture the main physics and chemistry occurring in this warm plasma, which is an important step towards predictive modelling for plasma-based gas conversion. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-05-09 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1385-8947 | ISBN | Additional Links | ||
| Impact Factor | 15.1 | Times cited | Open Access | ||
| Notes | This research was supported by the Excellence of Science FWO-FNRS project (FWO grant ID G0I1822N; EOS ID 40007511) and the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (grant agreement No. 810182–SCOPE ERC Synergy project, and grant agreement No. 101081162–PREPARE ERC Proof of Concept project). computational resources and services used in this work were provided by the HPC core facility CalcUA of the Universiteit Antwerpen, and VSC (Flemish Supercomputer Center), funded by the Research Foundation – Flanders (FWO) and the Flemish Government. | Approved | Most recent IF: 15.1; 2024 IF: 6.216 | ||
| Call Number | PLASMANT @ plasmant @ | Serial | 9132 | ||
| Permanent link to this record | |||||
| Author | Faraji, F.; Neyts, E.C.; Milošević, M.V.; Peeters, F.M. | ||||
| Title | Capillary Condensation of Water in Graphene Nanocapillaries | Type | A1 Journal ArticleUA | ||
| Year |
2024 | Publication | Nano Letters | Abbreviated Journal | Nano Lett. |
| Volume | 24 | Issue | 18 | Pages | 5625-5630 |
| Keywords | A1 Journal ArticleUA | ||||
| Abstract | Recent experiments have revealed that the macroscopic Kelvin equation remains surprisingly accurate even for nanoscale capillaries. This phenomenon was so far explained by the oscillatory behavior of the solid−liquid interfacial free energy. We here demonstrate thermodynamic and capillarity inconsistencies with this explanation. After revising the Kelvin equation, we ascribe its validity at nanoscale confinement to the effect of disjoining pressure. To substantiate our hypothesis, we employed molecular dynamics simulations to evaluate interfacial heat transfer and wetting properties. Our assessments unveil a breakdown in a previously established proportionality between the work of adhesion and the Kapitza conductance at capillary heights below 1.3 nm, where the dominance of the work of adhesion shifts primarily from energy to entropy. Alternatively, the peak density of the initial water layer can effectively probe the work of adhesion. Unlike under bulk conditions, high confinement renders the work of adhesion entropically unfavorable. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-05-08 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1530-6984 | ISBN | Additional Links | ||
| Impact Factor | 10.8 | Times cited | Open Access | ||
| Notes | This work was supported by Research Foundation-Flanders (FWO, project No. G099219N). The computational resources used in this work were provided by the HPC core facility CalcUA of the University of Antwerp, and the Flemish Supercomputer Center (VSC), funded by FWO and the Flemish Government. | Approved | Most recent IF: 10.8; 2024 IF: 12.712 | ||
| Call Number | UA @ lucian @ | Serial | 9123 | ||
| Permanent link to this record | |||||
| Author | Zhou, R.; Neek-Amal, M.; Peeters, F.M.; Bai, B.; Sun, C. | ||||
| Title | Interlink between Abnormal Water Imbibition in Hydrophilic and Rapid Flow in Hydrophobic Nanochannels | Type | A1 Journal ArticleUA | ||
| Year |
2024 | Publication | Physical Review Letters | Abbreviated Journal | Phys. Rev. Lett. |
| Volume | 132 | Issue | 18 | Pages | 184001 |
| Keywords | A1 Journal ArticleUA | ||||
| Abstract | Nanoscale extension and refinement of the Lucas-Washburn model is presented with a detailed analysis of recent experimental data and extensive molecular dynamics simulations to investigate rapid water flow and water imbibition within nanocapillaries. Through a comparative analysis of capillary rise in hydrophilic nanochannels, an unexpected reversal of the anticipated trend, with an abnormal peak, of imbibition length below the size of 3 nm was discovered in hydrophilic nanochannels, surprisingly sharing the same physical origin as the well-known peak observed in flow rate within hydrophobic nanochannels. The extended imbibition model is applicable across diverse spatiotemporal scales and validated against simulation results and existing experimental data for both hydrophilic and hydrophobic | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-04-30 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0031-9007 | ISBN | Additional Links | ||
| Impact Factor | 8.6 | Times cited | Open Access | ||
| Notes | We gratefully acknowledge the financial support pro- vided by the National Natural Science Foundation of China (Projects No. 52488201 and No. 52222606). Part of this project was supported by the Flemish Science Foundations (FWO-Vl) and the Iranian National Science Foundation (No. 4025061 and No. 4021261). | Approved | Most recent IF: 8.6; 2024 IF: 8.462 | ||
| Call Number | UA @ lucian @ | Serial | 9122 | ||
| Permanent link to this record | |||||
| Author | Vlasov, E.; Heyvaert, W.; Ni, B.; Van Gordon, K.; Girod, R.; Verbeeck, J.; Liz-Marzán, L.M.; Bals, S. | ||||
| Title | High-Throughput Morphological Chirality Quantification of Twisted and Wrinkled Gold Nanorods | Type | A1 Journal Article | ||
| Year |
2024 | Publication | ACS Nano | Abbreviated Journal | ACS Nano |
| Volume | Issue | Pages | |||
| Keywords | A1 Journal Article; Electron Microscopy for Materials Science (EMAT) ; | ||||
| Abstract | Chirality in gold nanostructures offers an exciting opportunity to tune their differential optical response to left- and right-handed circularly polarized light, as well as their interactions with biomolecules and living matter. However, tuning and understanding such interactions demands quantification of the structural features that are responsible for the chiral behavior. Electron tomography (ET) enables structural characterization at the single-particle level and has been used to quantify the helicity of complex chiral nanorods. However, the technique is time-consuming and consequently lacks statistical value. To address this issue, we introduce herein a high-throughput methodology that combines images acquired by secondary electron-based electron beam-induced current (SEEBIC) with quantitative image analysis. As a result, the geometric chirality of hundreds of nanoparticles can be quantified in less than 1 h. When combining the drastic gain in data collection efficiency of SEEBIC with a limited number of ET data sets, a better understanding of how the chiral structure of individual chiral nanoparticles translates into the ensemble chiroptical response can be reached. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-04-26 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1936-0851 | ISBN | Additional Links | ||
| Impact Factor | 17.1 | Times cited | Open Access | ||
| Notes | The authors acknowledge financial support by the European Research Council (ERC CoG No. 815128 REALNANO to S.B.) and from MCIN/AEI/10.13039/501100011033 (Grant PID2020-117779RB-I00 to L.M.L.-M and FPI Fellowship PRE2021-097588 to K.V.G.). Funded by the European Union under Project 101131111 − DELIGHT, JV acknowledges the eBEAM project supported by the European Union’s Horizon 2020 research and innovation program FETPROACT-EIC-07- 2020: emerging paradigms and communities. | Approved | Most recent IF: 17.1; 2024 IF: 13.942 | ||
| Call Number | EMAT @ emat @ | Serial | 9121 | ||
| Permanent link to this record | |||||
| Author | Guerrero, R.M.; Lemir, I.D.; Carrasco, S.; Fernández-Ruiz, C.; Kavak, S.; Pizarro, P.; Serrano, D.P.; Bals, S.; Horcajada, P.; Pérez, Y. | ||||
| Title | Scaling-Up Microwave-Assisted Synthesis of Highly Defective Pd@UiO-66-NH2Catalysts for Selective Olefin Hydrogenation under Ambient Conditions | Type | A1 Journal Article | ||
| Year |
2024 | Publication | ACS Applied Materials & Interfaces | Abbreviated Journal | ACS Appl. Mater. Interfaces |
| Volume | Issue | Pages | |||
| Keywords | A1 Journal Article; Electron Microscopy for Materials Science (EMAT) ; | ||||
| Abstract | The need to develop green and cost-effective industrial catalytic processes has led to growing interest in preparing more robust, efficient, and selective heterogeneous catalysts at a large scale. In this regard, microwave-assisted synthesis is a fast method for fabricating heterogeneous catalysts (including metal oxides, zeolites, metal–organic frameworks, and supported metal nanoparticles) with enhanced catalytic properties, enabling synthesis scale-up. Herein, the synthesis of nanosized UiO-66-NH2 was optimized via a microwave-assisted hydrothermal method to obtain defective matrices essential for the stabilization of metal nanoparticles, promoting catalytically active sites for hydrogenation reactions (760 kg·m–3·day–1 space time yield, STY). Then, this protocol was scaled up in a multimodal microwave reactor, reaching 86% yield (ca. 1 g, 1450 kg·m–3·day–1 STY) in only 30 min. Afterward, Pd nanoparticles were formed in situ decorating the nanoMOF by an effective and fast microwave-assisted hydrothermal method, resulting in the formation of Pd@UiO-66-NH2 composites. Both the localization and oxidation states of Pd nanoparticles (NPs) in the MOF were achieved using high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) and X-ray photoelectron spectroscopy (XPS), respectively. The optimal composite, loaded with 1.7 wt % Pd, exhibited an extraordinary catalytic activity (>95% yield, 100% selectivity) under mild conditions (1 bar H2, 25 °C, 1 h reaction time), not only in the selective hydrogenation of a variety of single alkenes (1-hexene, 1-octene, 1-tridecene, cyclohexene, and tetraphenyl ethylene) but also in the conversion of a complex mixture of alkenes (i.e., 1-hexene, 1-tridecene, and anethole). The results showed a powerful interaction and synergy between the active phase (Pd NPs) and the catalytic porous scaffold (UiO-66-NH2), which are essential for the selectivity and recyclability. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-04-26 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1944-8244 | ISBN | Additional Links | ||
| Impact Factor | 9.5 | Times cited | Open Access | ||
| Notes | The authors gratefully acknowledge financial support from “Comunidad de Madrid” and European Regional Development Fund-FEDER through the project HUB MADRID+CIRCULAR; the State Research Agency (MCIN/AEI /10.13039/501100011033) through the grant with reference number CEX2019-000931-M received in the 2019 call for “Severo Ochoa Centres of Excellence” and “María de Maeztu Units of Excellence” of the State Programme for Knowledge Generation and Scientific and Technological Strengthening of the R&D&I System; and MICIU through the project “NAPOLION” (PID2022-139956OB-I00). S.K. acknowledges the Flemish Fund for Scientific Research (FWO Vlaanderen) through a PhD research grant (1181124N). | Approved | Most recent IF: 9.5; 2024 IF: 7.504 | ||
| Call Number | EMAT @ emat @ | Serial | 9126 | ||
| Permanent link to this record | |||||
| Author | Cai, Y.; Mei, D.; Chen, Y.; Bogaerts, A.; Tu, X. | ||||
| Title | Machine learning-driven optimization of plasma-catalytic dry reforming of methane | Type | A1 Journal Article | ||
| Year |
2024 | Publication | Journal of Energy Chemistry | Abbreviated Journal | Journal of Energy Chemistry |
| Volume | 96 | Issue | Pages | 153-163 | |
| Keywords | A1 Journal Article; Plasma catalysis Machine learning Process optimization Dry reforming of methane Syngas production; Plasma, laser ablation and surface modeling Antwerp (PLASMANT) ; | ||||
| Abstract | This study investigates the dry reformation of methane (DRM) over Ni/Al2O3 catalysts in a dielectric barrier discharge (DBD) non-thermal plasma reactor. A novel hybrid machine learning (ML) model is developed to optimize the plasma-catalytic DRM reaction with limited experimental data. To address the non-linear and complex nature of the plasma-catalytic DRM process, the hybrid ML model integrates three well-established algorithms: regression trees, support vector regression, and artificial neural networks. A genetic algorithm (GA) is then used to optimize the hyperparameters of each algorithm within the hybrid ML model. The ML model achieved excellent agreement with the experimental data, demonstrating its efficacy in accurately predicting and optimizing the DRM process. The model was subsequently used to investigate the impact of various operating parameters on the plasma-catalytic DRM performance. We found that the optimal discharge power (20 W), CO2/CH4 molar ratio (1.5), and Ni loading (7.8 wt%) resulted in the maximum energy yield at a total flow rate of 51 mL/min. Furthermore, we investigated the relative significance of each operating parameter on the performance of the plasmacatalytic DRM process. The results show that the total flow rate had the greatest influence on the conversion, with a significance exceeding 35% for each output, while the Ni loading had the least impact on the overall reaction performance. This hybrid model demonstrates a remarkable ability to extract valuable insights from limited datasets, enabling the development and optimization of more efficient and selective plasma-catalytic chemical processes. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-04-25 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2095-4956 | ISBN | Additional Links | ||
| Impact Factor | 13.1 | Times cited | Open Access | ||
| Notes | This project received funding from the European Union’s Hori- zon 2020 research and innovation program under the Marie Sklodowska-Curie grant agreement No. 813393. | Approved | Most recent IF: 13.1; 2024 IF: 2.594 | ||
| Call Number | PLASMANT @ plasmant @ | Serial | 9124 | ||
| Permanent link to this record | |||||
| Author | Chakraborty, J.; Chatterjee, A.; Molkens, K.; Nath, I.; Arenas Esteban, D.; Bourda, L.; Watson, G.; Liu, C.; Van Thourhout, D.; Bals, S.; Geiregat, P.; Van der Voort, P. | ||||
| Title | Decoding Excimer Formation in Covalent–Organic Frameworks Induced by Morphology and Ring Torsion | Type | A1 Journal Article | ||
| Year |
2024 | Publication | Advanced Materials | Abbreviated Journal | Advanced Materials |
| Volume | Issue | Pages | |||
| Keywords | A1 Journal Article; Electron Microscopy for Materials Science (EMAT) ; | ||||
| Abstract | A thorough and quantitative understanding of the fate of excitons in covalent–organic frameworks (COFs) after photoexcitation is essential for their augmented optoelectronic and photocatalytic applications via precise structure tuning. The synthesis of a library of COFs having identical chemical backbone with impeded conjugation, but varied morphology and surface topography to study the effect of these physical properties on the photophysics of the materials is herein reported. The variation of crystallite size and surface topography substantified different aggregation pattern in the COFs, which leads to disparities in their photoexcitation and relaxation properties. Depending on aggregation, an inverse correlation between bulk luminescence decay time and exciton binding energy of the materials is perceived. Further transient absorption spectroscopic analysis confirms the presence of highly localized, immobile, Frenkel excitons (of diameter 0.3–0.5 nm) via an absence of annihilation at high density, most likely induced by structural torsion of the COF skeletons, which in turn preferentially relaxes via long‐lived (nanosecond to microsecond) excimer formation (in femtosecond scale) over direct emission. These insights underpin the importance of structural and topological design of COFs for their targeted use in photocatalysis. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-04-22 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0935-9648 | ISBN | Additional Links | ||
| Impact Factor | 29.4 | Times cited | Open Access | ||
| Notes | PVDV, JC, AC, and IN acknowledge the FWO-Vlaanderen for research grant G020521N and the research board of UGent (BOF) through a Concerted Research Action (GOA010-17). JC acknowledges UGent for BOF postdoctoral grant (2022.0032.01). AC acknowledges FWO- Vlaanderen for postdoctoral grant (12T7521N). KM, DVT and PG acknowledges FWO- Vlaanderen for research grant G0B2921N. SB and DAE acknowledge financial support from ERC Consolidator Grant Number 815128 REALNANO. CHL acknowledges China Scholarship Council doctoral grant (201908110280). PVDV acknowledges Hercules Project AUGE/17/07 for the UV VIS DRS spectrometer and UGent BASBOF BOF20/BAS/015 for the powder X-Ray Diffractometer. PG thanks UGent for support of the Core Facility NOLIMITS. | Approved | Most recent IF: 29.4; 2024 IF: 19.791 | ||
| Call Number | EMAT @ emat @ | Serial | 9118 | ||
| Permanent link to this record | |||||
| Author | Chakraborty, J.; Chatterjee, A.; Molkens, K.; Nath, I.; Arenas Esteban, D.; Bourda, L.; Watson, G.; Liu, C.; Van Thourhout, D.; Bals, S.; Geiregat, P.; Van der Voort, P. | ||||
| Title | Decoding Excimer Formation in Covalent–Organic Frameworks Induced by Morphology and Ring Torsion | Type | A1 Journal Article | ||
| Year |
2024 | Publication | Advanced Materials | Abbreviated Journal | Advanced Materials |
| Volume | Issue | Pages | |||
| Keywords | A1 Journal Article; Electron Microscopy for Materials Science (EMAT) ; | ||||
| Abstract | A thorough and quantitative understanding of the fate of excitons in covalent–organic frameworks (COFs) after photoexcitation is essential for their augmented optoelectronic and photocatalytic applications via precise structure tuning. The synthesis of a library of COFs having identical chemical backbone with impeded conjugation, but varied morphology and surface topography to study the effect of these physical properties on the photophysics of the materials is herein reported. The variation of crystallite size and surface topography substantified different aggregation pattern in the COFs, which leads to disparities in their photoexcitation and relaxation properties. Depending on aggregation, an inverse correlation between bulk luminescence decay time and exciton binding energy of the materials is perceived. Further transient absorption spectroscopic analysis confirms the presence of highly localized, immobile, Frenkel excitons (of diameter 0.3–0.5 nm) via an absence of annihilation at high density, most likely induced by structural torsion of the COF skeletons, which in turn preferentially relaxes via long‐lived (nanosecond to microsecond) excimer formation (in femtosecond scale) over direct emission. These insights underpin the importance of structural and topological design of COFs for their targeted use in photocatalysis. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-04-22 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0935-9648 | ISBN | Additional Links | ||
| Impact Factor | 29.4 | Times cited | Open Access | ||
| Notes | PVDV, JC, AC, and IN acknowledge the FWO-Vlaanderen for research grant G020521N and the research board of UGent (BOF) through a Concerted Research Action (GOA010-17). JC acknowledges UGent for BOF postdoctoral grant (2022.0032.01). AC acknowledges FWOVlaanderen for postdoctoral grant (12T7521N). KM, DVT and PG acknowledges FWOVlaanderen for research grant G0B2921N. SB and DAE acknowledge financial support from ERC Consolidator Grant Number 815128 REALNANO. CHL acknowledges China Scholarship Council doctoral grant (201908110280). PVDV acknowledges Hercules Project AUGE/17/07 for the UV VIS DRS spectrometer and UGent BASBOF BOF20/BAS/015 for the powder X-Ray Diffractometer. PG thanks UGent for support of the Core Facility NOLIMITS. | Approved | Most recent IF: 29.4; 2024 IF: 19.791 | ||
| Call Number | EMAT @ emat @ | Serial | 9130 | ||
| Permanent link to this record | |||||
| Author | Xu, W.; Van Alphen, S.; Galvita, V.V.; Meynen, V.; Bogaerts, A. | ||||
| Title | Effect of Gas Composition on Temperature and CO2Conversion in a Gliding Arc Plasmatron reactor: Insights for Post‐Plasma Catalysis from Experiments and Computation | Type | A1 Journal Article | ||
| Year |
2024 | Publication | ChemSusChem | Abbreviated Journal | ChemSusChem |
| Volume | Issue | Pages | |||
| Keywords | A1 Journal Article; CO2 conversion · Plasma · Gliding arc plasmatron · Temperature profiles · Computational modelling; Plasma, laser ablation and surface modeling Antwerp (PLASMANT) ; | ||||
| Abstract | Plasma‐based CO<sub>2</sub>conversion has attracted increasing interest. However, to understand the impact of plasma operation on post‐plasma processes, we studied the effect of adding N<sub>2</sub>, N<sub>2</sub>/CH<sub>4</sub>and N<sub>2</sub>/CH<sub>4</sub>/H<sub>2</sub>O to a CO<sub>2</sub>gliding arc plasmatron (GAP) to obtain valuable insights into their impact on exhaust stream composition and temperature, which will serve as feed gas and heat for post‐plasma catalysis (PPC). Adding N<sub>2</sub>improves the CO<sub>2</sub>conversion from 4 % to 13 %, and CH<sub>4</sub>addition further promotes it to 44 %, and even to 61 % at lower gas flow rate (6 L/min), allowing a higher yield of CO and hydrogen for PPC. The addition of H<sub>2</sub>O, however, reduces the CO<sub>2</sub>conversion from 55 % to 22 %, but it also lowers the energy cost, from 5.8 to 3 kJ/L. Regarding the temperature at 4.9 cm post‐plasma, N<sub>2</sub>addition increases the temperature, while the CO<sub>2</sub>/CH<sub>4</sub>ratio has no significant effect on temperature. We also calculated the temperature distribution with computational fluid dynamics simulations. The obtained temperature profiles (both experimental and calculated) show a decreasing trend with distance to the exhaust and provide insights in where to position a PPC bed. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-04-11 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1864-5631 | ISBN | Additional Links | ||
| Impact Factor | 8.4 | Times cited | Open Access | ||
| Notes | We acknowledge the VLAIO Catalisti Moonshot project D2M and the VLAIO Catalisti transition project CO2PERATE (HBC.2017.0692) for financial support. We acknowledge Gilles Van Loon for his help to make the quartz and steel devices for the reactor. Vladimir V. Galvita also acknowledges a personal grant from the Research Fund of Ghent University (BOF; 01N16319). | Approved | Most recent IF: 8.4; 2024 IF: 7.226 | ||
| Call Number | PLASMANT @ plasmant @ | Serial | 9128 | ||
| Permanent link to this record | |||||
| Author | Esteban, D.A.; Chamocho, E.G.; Carretero González, J.; Urones Garrote, E.; Otero Díaz, L.C.; Brande, D.Á. | ||||
| Title | Enhancing Electrochemical Properties of Walnut Shell Activated Carbon with Embedded MnO Clusters for Supercapacitor Applications | Type | A1 Journal Article | ||
| Year |
2024 | Publication | Batteries & Supercaps | Abbreviated Journal | Batteries & Supercaps |
| Volume | Issue | Pages | |||
| Keywords | A1 Journal Article; Electron Microscopy for Materials Science (EMAT) ; | ||||
| Abstract | Activated carbon (AC) materials from renewable sources are widely used in electrochemical applications due to their well‐known high surface area. However, their application as electrode material in double‐layer electrochemical devices may be limited due to their relatively low electrical conductivity and lightweight. To overcome these limitations, the incorporation of pseudocapacitance metal oxide nanoparticles is an optimum approach. These nanoparticles can provide a second energy storage mechanism to the composite, mitigating the loss of surface area associated with their incorporation. As a result, the composite material is endowed with increased conductivity and higher density, making it more suitable for practical implementation in real devices. In this study, we have incorporated a fine dispersion of 1 % of MnO clusters into a highly porous activated carbon synthesized from walnut shells (WAC). The high‐resolution electron microscopy studies, combined with their related analytical techniques, allow us to determine the presence of the cluster within the matrix carbon precisely. The resulting MnO@WAC composite demonstrated significantly improved capacitive behavior compared with the WAC material, with increased volumetric capacitance and higher charge retention at higher current densities. The composite‘s electrochemical performance suggests its potential as a promising electrode material for supercapacitors, addressing drawbacks associated with traditional AC materials. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-04-08 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2566-6223 | ISBN | Additional Links | ||
| Impact Factor | Times cited | Open Access | |||
| Notes | Grants PID2020-112848RB-C21 funded by MCIN/AEI/ 10.13039/501100011033 and by the European Union PRTR funding through projects are acknowledged. Access to the ICTS- CNME for TEM is also acknowledged. | Approved | Most recent IF: NA | ||
| Call Number | EMAT @ emat @ | Serial | 9119 | ||
| Permanent link to this record | |||||
| Author | Leinders, G.; Grendal, O.G.; Arts, I.; Bes, R.; Prozheev, I.; Orlat, S.; Fitch, A.; Kvashnina, K.; Verwerft, M. | ||||
| Title | Refinement of the uranium dispersion corrections from anomalous diffraction | Type | A1 Journal Article | ||
| Year |
2024 | Publication | Journal of Applied Crystallography | Abbreviated Journal | J Appl Cryst |
| Volume | 57 | Issue | 2 | Pages | 284-295 |
| Keywords | A1 Journal Article; Electron Microscopy for Materials Science (EMAT) ; | ||||
| Abstract | The evolution of the uranium chemical state in uranium compounds, principally in the oxides, is of concern in the context of nuclear fuel degradation under storage and repository conditions, and in accident scenarios. The U–O system shows complicated phase relations between single-valence uranium dioxide (UO<sub>2</sub>) and different mixed-valence compounds (<italic>e.g.</italic>U<sub>4</sub>O<sub>9</sub>, U<sub>3</sub>O<sub>7</sub>and U<sub>3</sub>O<sub>8</sub>). To try resolving the electronic structure associated with unique atomic positions, a combined application of diffraction and spectroscopic techniques, such as diffraction anomalous fine structure (DAFS), can be considered. Reported here is the application of two newly developed routines for assessing a DAFS data set, with the aim of refining the uranium X-ray dispersion corrections. High-resolution anomalous diffraction data were acquired from polycrystalline powder samples of UO<sub>2</sub>(containing tetravalent uranium) and potassium uranate (KUO<sub>3</sub>, containing pentavalent uranium) using synchrotron radiation in the vicinity of the U<italic>L</italic><sub>3</sub>edge (17.17 keV). Both routines are based on an iterative refinement of the dispersion corrections, but they differ in either using the intensity of a selection of reflections or doing a full-pattern (Rietveld method) refinement. The uranium dispersion corrections obtained using either method are in excellent agreement with each other, and they show in great detail the chemical shifts and differences in fine structure expected for tetravalent and pentavalent uranium. This approach may open new possibilities for the assessment of other, more complicated, materials such as mixed-valence compounds. Additionally, the DAFS methodology can offer a significant resource optimization because each data set contains both structural (diffraction) and chemical (spectroscopy) information, which can avoid the requirement to use multiple experimental stations at synchrotron sources. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-04-01 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1600-5767 | ISBN | Additional Links | ||
| Impact Factor | 6.1 | Times cited | Open Access | ||
| Notes | FPS Economy, SF-CORMOD; | Approved | Most recent IF: 6.1; 2024 IF: 2.495 | ||
| Call Number | EMAT @ emat @ | Serial | 9127 | ||
| Permanent link to this record | |||||
| Author | Ignatova, K.; Vlasov, E.; Seddon, S.D.; Gauquelin, N.; Verbeeck, J.; Wermeille, D.; Bals, S.; Hase, T.P.A.; Arnalds, U.B. | ||||
| Title | Phase coexistence induced surface roughness in V2O3/Ni magnetic heterostructures | Type | A1 Journal Article | ||
| Year |
2024 | Publication | APL Materials | Abbreviated Journal | |
| Volume | 12 | Issue | 4 | Pages | |
| Keywords | A1 Journal Article; Electron Microscopy for Materials Science (EMAT) ; | ||||
| Abstract | We present an investigation of the microstructure changes in V2O3 as it goes through its inherent structural phase transition. Using V2O3 films with a well-defined crystal structure deposited by reactive magnetron sputtering on r-plane Al2O3 substrates, we study the phase coexistence region and its impact on the surface roughness of the films and the magnetic properties of overlying Ni magnetic layers in V2O3/Ni hybrid magnetic heterostructures. The simultaneous presence of two phases in V2O3 during its structural phase transition was identified with high resolution x-ray diffraction and led to an increase in surface roughness observed using x-ray reflectivity. The roughness reaches its maximum at the midpoint of the transition. In V2O3/Ni hybrid heterostructures, we find a concomitant increase in the coercivity of the magnetic layer correlated with the increased roughness of the V2O3 surface. The chemical homogeneity of the V2O3 is confirmed through transmission electron microscopy analysis. High-angle annular dark field imaging and electron energy loss spectroscopy reveal an atomically flat interface between Al2O3 and V2O3, as well as a sharp interface between V2O3 and Ni. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-04-01 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2166-532X | ISBN | Additional Links | ||
| Impact Factor | 6.1 | Times cited | Open Access | ||
| Notes | This work was supported by the funding from the University of Iceland Research Fund, the Icelandic Research Fund Grant No. 207111. Instrumentation funding from the Icelandic Infrastructure Fund is acknowledged. This work was based on experiments per- formed at the BM28 (XMaS) beamline at the European Synchrotron Radiation Facility, Grenoble, France. XMaS is a National Research Facility funded by the UK EPSRC and managed by the Universi- ties of Liverpool and Warwick. This project has received funding from the European Union’s Horizon 2020 research and innovation program under Grant Agreement No. 823717—ESTEEM3. | Approved | Most recent IF: 6.1; 2024 IF: 4.335 | ||
| Call Number | EMAT @ emat @ | Serial | 9120 | ||
| Permanent link to this record | |||||
| Author | Albrechts, M.; Tsonev, I.; Bogaerts, A. | ||||
| Title | Investigation of O atom kinetics in O2plasma and its afterglow | Type | A1 Journal Article | ||
| Year |
2024 | Publication | Plasma Sources Science and Technology | Abbreviated Journal | Plasma Sources Sci. Technol. |
| Volume | 33 | Issue | 4 | Pages | 045017 |
| Keywords | A1 Journal Article; oxygen plasma, pseudo-1D plug-flow kinetic model, O atoms, low-pressure validation, atmospheric pressure microwave torch; Plasma, laser ablation and surface modeling Antwerp (PLASMANT) ; | ||||
| Abstract | We have developed a comprehensive kinetic model to study the O atom kinetics in an O<sub>2</sub>plasma and its afterglow. By adopting a pseudo-1D plug-flow formalism within the kinetic model, our aim is to assess how far the O atoms travel in the plasma afterglow, evaluating its potential as a source of O atoms for post-plasma gas conversion applications. Since we could not find experimental data for pure O<sub>2</sub>plasma at atmospheric pressure, we first validated our model at low pressure (1–10 Torr) where very good experimental data are available. Good agreement between our model and experiments was achieved for the reduced electric field, gas temperature and the densities of the dominant neutral species, i.e. O<sub>2</sub>(a), O<sub>2</sub>(b) and O. Subsequently, we confirmed that the chemistry set is consistent with thermodynamic equilibrium calculations at atmospheric pressure. Finally, we investigated the O atom densities in the O<sub>2</sub>plasma and its afterglow, for which we considered a microwave O<sub>2</sub>plasma torch, operating at a pressure between 0.1 and 1 atm, for a flow rate of 20 slm and an specific energy input of 1656 kJ mol<sup>−1</sup>. Our results show that for both pressure conditions, a high dissociation degree of ca. 92% is reached within the discharge. However, the O atoms travel much further in the plasma afterglow for<italic>p</italic>= 0.1 atm (9.7 cm) than for<italic>p</italic>= 1 atm (1.4 cm), attributed to the longer lifetime (3.8 ms at 0.1 atm vs 1.8 ms at 1 atm) resulting from slower three-body recombination kinetics, as well as a higher volumetric flow rate. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-04-01 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0963-0252 | ISBN | Additional Links | ||
| Impact Factor | 3.8 | Times cited | Open Access | ||
| Notes | This research was supported by the Horizon Europe Framework Program ‘Research and Innovation Actions’ (RIA), Project CANMILK (Grant No. 101069491). | Approved | Most recent IF: 3.8; 2024 IF: 3.302 | ||
| Call Number | PLASMANT @ plasmant @ | Serial | 9125 | ||
| Permanent link to this record | |||||
| Author | De Meyer, R.; Gorbanev, Y.; Ciocarlan, R.-G.; Cool, P.; Bals, S.; Bogaerts, A. | ||||
| Title | Importance of plasma discharge characteristics in plasma catalysis: Dry reforming of methane vs. ammonia synthesis | Type | A1 Journal Article | ||
| Year |
2024 | Publication | Chemical Engineering Journal | Abbreviated Journal | Chemical Engineering Journal |
| Volume | 488 | Issue | Pages | 150838 | |
| Keywords | A1 Journal Article; Gas conversion Dry reforming of methane Ammonia Microdischarges Dielectric barrier discharge; Plasma, laser ablation and surface modeling Antwerp (PLASMANT) ; | ||||
| Abstract | Plasma catalysis is a rapidly growing field, often employing a packed-bed dielectric barrier discharge plasma reactor. Such dielectric barrier discharges are complex, especially when a packing material (e.g., a catalyst) is introduced in the discharge volume. Catalysts are known to affect the plasma discharge, though the underlying mechanisms influencing the plasma physics are not fully understood. Moreover, the effect of the catalysts on the plasma discharge and its subsequent effect on the overall performance is often overlooked. In this work, we deliberately design and synthesize catalysts to affect the plasma discharge in different ways. These Ni or Co alumina-based catalysts are used in plasma-catalytic dry reforming of methane and ammonia synthesis. Our work shows that introducing a metal to the dielectric packing can affect the plasma discharge, and that the distribution of the metal is crucial in this regard. Further, the altered discharge can greatly influence the overall performance. In an atmospheric pressure dielectric barrier discharge reactor, this apparently more uniform plasma yields a significantly better performance for ammonia synthesis compared to the more conventional filamentary discharge, while it underperforms in dry reforming of methane. This study stresses the importance of analyzing the plasma discharge in plasma catalysis experiments. We hope this work encourages a more critical view on the plasma discharge characteristics when studying various catalysts in a plasma reactor. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-03-30 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1385-8947 | ISBN | Additional Links | ||
| Impact Factor | 15.1 | Times cited | Open Access | ||
| Notes | This research was supported through long-term structural funding (Methusalem FFB15001C) and by the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme with grant agreement No 810182 (SCOPE ERC Synergy project) and with grant agreement No 815128 (REALNANO). We acknowledge the practical contribution of Senne Van Doorslaer. | Approved | Most recent IF: 15.1; 2024 IF: 6.216 | ||
| Call Number | PLASMANT @ plasmant @ | Serial | 9115 | ||
| Permanent link to this record | |||||
| Author | Gorbanev, Y.; Fedirchyk, I.; Bogaerts, A. | ||||
| Title | Plasma catalysis in ammonia production and decomposition: Use it, or lose it? | Type | A1 Journal Article | ||
| Year |
2024 | Publication | Current Opinion in Green and Sustainable Chemistry | Abbreviated Journal | Current Opinion in Green and Sustainable Chemistry |
| Volume | 47 | Issue | Pages | 100916 | |
| Keywords | A1 Journal Article; Plasma Nitrogen fixation Ammonia Plasma catalysis Production and decomposition; Plasma, laser ablation and surface modeling Antwerp (PLASMANT) ; | ||||
| Abstract | The combination of plasma with catalysis for the synthesis and decomposition of NH3 is an attractive route to the production of carbon-neutral fertiliser and energy carriers and its conversion into H2. Recent years have seen fast developments in the field of plasma-catalytic NH3 life cycle. This work summarises the most recent advances in plasma-catalytic and related NH3-focussed processes, identifies some of the most important discoveries, and addresses plausible strategies for future developments in plasma-based NH3 technology. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-03-29 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2452-2236 | ISBN | Additional Links | ||
| Impact Factor | 9.3 | Times cited | Open Access | ||
| Notes | The work was supported by the Fund for Scientific Research (FWO) Flanders Bioeconomy project (grant G0G2322N) funded by the European Union-NextGe- nerationEU, the HyPACT project funded by the Belgian Energy Transition Fund, and the MSCA4Ukraine project 1233629 funded by the European Union. | Approved | Most recent IF: 9.3; 2024 IF: NA | ||
| Call Number | PLASMANT @ plasmant @ | Serial | 9117 | ||
| Permanent link to this record | |||||
| Author | Heirman, P.; Verloy, R.; Baroen, J.; Privat-Maldonado, A.; Smits, E.; Bogaerts, A. | ||||
| Title | Liquid treatment with a plasma jet surrounded by a gas shield: effect of the treated substrate and gas shield geometry on the plasma effluent conditions | Type | A1 Journal Article | ||
| Year |
2024 | Publication | Journal of Physics D: Applied Physics | Abbreviated Journal | J. Phys. D: Appl. Phys. |
| Volume | 57 | Issue | 11 | Pages | 115204 |
| Keywords | A1 Journal Article; atmospheric pressure plasma jet, 2D fluid modeling, gas shield, in vitro treatment, plasma-liquid; Plasma, laser ablation and surface modeling Antwerp (PLASMANT) ; | ||||
| Abstract | The treatment of a well plate by an atmospheric pressure plasma jet is common for<italic>in vitro</italic>plasma medicine research. Here, reactive species are largely produced through the mixing of the jet effluent with the surrounding atmosphere. This mixing can be influenced not only by the ambient conditions, but also by the geometry of the treated well. To limit this influence and control the atmosphere, a shielding gas is sometimes applied. However, the interplay between the gas shield and the well geometry has not been investigated. In this work, we developed a 2D-axisymmetric computational fluid dynamics model of the kINPen plasma jet, to study the mixing of the jet effluent with the surrounding atmosphere, with and without gas shield. Our computational and experimental results show that the choice of well type can have a significant influence on the effluent conditions, as well as on the effectiveness of the gas shield. Furthermore, the geometry of the shielding gas device can substantially influence the mixing as well. Our results provide a deeper understanding of how the choice of setup geometry can influence the plasma treatment, even when all other operating parameters are unchanged. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 001127372200001 | Publication Date | 2024-03-15 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0022-3727 | ISBN | Additional Links | UA library record; WoS full record | |
| Impact Factor | 3.4 | Times cited | Open Access | Not_Open_Access | |
| Notes | Fund for Scientific Research Flanders, 1100421N ; | Approved | Most recent IF: 3.4; 2024 IF: 2.588 | ||
| Call Number | PLASMANT @ plasmant @c:irua:201999 | Serial | 8977 | ||
| Permanent link to this record | |||||
| Author | Gerrits, N.; Jackson, B.; Bogaerts, A. | ||||
| Title | Accurate Reaction Probabilities for Translational Energies on Both Sides of the Barrier of Dissociative Chemisorption on Metal Surfaces | Type | A1 Journal Article | ||
| Year |
2024 | Publication | The Journal of Physical Chemistry Letters | Abbreviated Journal | J. Phys. Chem. Lett. |
| Volume | 15 | Issue | 9 | Pages | 2566-2572 |
| Keywords | A1 Journal Article; Plasma, laser ablation and surface modeling Antwerp (PLASMANT) ; | ||||
| Abstract | Molecular dynamics simulations are essential for a better understanding of dissociative chemisorption on metal surfaces, which is often the rate-controlling step in heterogeneous and plasma catalysis. The workhorse quasi-classical trajectory approach ubiquitous in molecular dynamics is able to accurately predict reactivity only for high translational and low vibrational energies. In contrast, catalytically relevant conditions generally involve low translational and elevated vibrational energies. Existing quantum dynamics approaches are intractable or approximate as a result of the large number of degrees of freedom present in molecule−metal surface reactions. Here, we extend a ring polymer molecular dynamics approach to fully include, for the first time, the degrees of freedom of a moving metal surface. With this approach, experimental sticking probabilities for the dissociative chemisorption of methane on Pt(111) are reproduced for a large range of translational and vibrational energies by including nuclear quantum effects and employing full-dimensional simulations. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-03-07 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1948-7185 | ISBN | Additional Links | ||
| Impact Factor | 5.7 | Times cited | Open Access | ||
| Notes | Nick Gerrits has been financially supported through a Dutch Research Council (NWO) Rubicon grant (019.202EN.012). The computational resources and services used in this work were provided by the high performance computing (HPC) core facility CalcUA of the Universiteit Antwerpen and the Flemish Supercomputer Center (VSC) funded by the Research Foundation−Flanders (FWO) and the Flemish Government. The authors thank Mark Somers for useful discussions. | Approved | Most recent IF: 5.7; 2024 IF: 9.353 | ||
| Call Number | PLASMANT @ plasmant @ | Serial | 9114 | ||
| Permanent link to this record | |||||
| Author | Grünewald, L.; Chezganov, D.; De Meyer, R.; Orekhov, A.; Van Aert, S.; Bogaerts, A.; Bals, S.; Verbeeck, J. | ||||
| Title | In Situ Plasma Studies Using a Direct Current Microplasma in a Scanning Electron Microscope | Type | A1 Journal Article | ||
| Year |
2024 | Publication | Advanced Materials Technologies | Abbreviated Journal | Adv Materials Technologies |
| Volume | Issue | Pages | |||
| Keywords | A1 Journal Article; Electron Microscopy for Materials Science (EMAT) ; | ||||
| Abstract | Microplasmas can be used for a wide range of technological applications and to improve the understanding of fundamental physics. Scanning electron microscopy, on the other hand, provides insights into the sample morphology and chemistry of materials from the mm‐ down to the nm‐scale. Combining both would provide direct insight into plasma‐sample interactions in real‐time and at high spatial resolution. Up till now, very few attempts in this direction have been made, and significant challenges remain. This work presents a stable direct current glow discharge microplasma setup built inside a scanning electron microscope. The experimental setup is capable of real‐time in situ imaging of the sample evolution during plasma operation and it demonstrates localized sputtering and sample oxidation. Further, the experimental parameters such as varying gas mixtures, electrode polarity, and field strength are explored and experimental<italic>V</italic>–<italic>I</italic>curves under various conditions are provided. These results demonstrate the capabilities of this setup in potential investigations of plasma physics, plasma‐surface interactions, and materials science and its practical applications. The presented setup shows the potential to have several technological applications, for example, to locally modify the sample surface (e.g., local oxidation and ion implantation for nanotechnology applications) on the µm‐scale. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-02-25 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2365-709X | ISBN | Additional Links | ||
| Impact Factor | 6.8 | Times cited | Open Access | OpenAccess | |
| Notes | L.G., S.B., and J.V. acknowledge support from the iBOF-21-085 PERsist research fund. D.C., S.V.A., and J.V. acknowledge funding from a TOPBOF project of the University of Antwerp (FFB 170366). R.D.M., A.B., and J.V. acknowledge funding from the Methusalem project of the University of Antwerp (FFB 15001A, FFB 15001C). A.O. and J.V. acknowledge funding from the Research Foundation Flanders (FWO, Belgium) project SBO S000121N. | Approved | Most recent IF: 6.8; 2024 IF: NA | ||
| Call Number | EMAT @ emat @ | Serial | 8995 | ||
| Permanent link to this record | |||||
| Author | Vandemeulebroucke, D.; Batuk, M.; Hajizadeh, A.; Wastiaux, M.; Roussel, P.; Hadermann, J. | ||||
| Title | Incommensurate Modulations and Perovskite Growth in LaxSr2–xMnO4−δAffecting Solid Oxide Fuel Cell Conductivity | Type | A1 Journal Article | ||
| Year |
2024 | Publication | Chemistry of Materials | Abbreviated Journal | Chem. Mater. |
| Volume | Issue | Pages | |||
| Keywords | A1 Journal Article; Electron Microscopy for Materials Science (EMAT) ; | ||||
| Abstract | Ruddlesden-Popper La????Sr2−????MnO4−???? materials are interesting symmetric solid oxide fuel cell electrodes due to their good redox stability, mixed ionic and electronic conducting behavior and thermal expansion that matches well with common electrolytes. In reducing environments – as at a solid oxide fuel cell anode – the x = 0.5 member, i.e. La0.5Sr1.5MnO4−????, has a much higher total conductivity than compounds with a different La/Sr ratio, although all those compositions have the same K2NiF4-type I4/mmm structure. The origin for this conductivity difference is not yet known in literature. Now, a combination of in-situ and ex-situ 3D electron diffraction, high-resolution imaging, energy-dispersive X-ray analysis and electron energy-loss spectroscopy uncovered clear differences between x=0.25 and x=0.5 in the pristine structure, as well as in the transformations upon high-temperature reduction. In La0.5Sr1.5MnO4−????, Ruddlesden-Popper n=2 layer defects and an amorphous surface layer are present, but not in La0.25Sr1.75MnO4−????. After annealing at 700°C in 5% H2/Ar, La0.25Sr1.75MnO4−???? transforms to a tetragonal 2D incommensurately modulated structure with modulation vectors ⃗????1 = 0.2848(1) · (⃗????* +⃗????*) and ⃗????2 =0.2848(1) · (⃗????* – ⃗????*), whereas La0.5Sr1.5MnO4−???? only partially transforms to an orthorhombic 1D incommensurately modulated structure, with ⃗???? = 0.318(2) · ⃗????*. Perovskite domains grow at the crystal edge at 700°C in 5% H2 or vacuum, due to the higher La concentration on the surface compared to the bulk, which leads to a different thermodynamic equilibrium. Since it is known that a lower degree of oxygen vacancy ordering and a higher amount of perovskite blocks enhance oxygen mobility, those differences in defect structure and structural transformation upon reduction, might all contribute to the higher conductivity of La0.5Sr1.5MnO4−???? in solid oxide fuel cell anode conditions compared to other La/Sr ratios. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | English | Wos | Publication Date | 2024-02-20 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0897-4756 | ISBN | Additional Links | ||
| Impact Factor | 8.6 | Times cited | Open Access | Not_Open_Access | |
| Notes | Universiteit Antwerpen, BOF TOP 38689 ; Fonds Wetenschappelijk Onderzoek, I003218N ; European Commission NanED, 956099 ; | Approved | Most recent IF: 8.6; 2024 IF: 9.466 | ||
| Call Number | EMAT @ emat @ | Serial | 8997 | ||
| Permanent link to this record | |||||
| Author | Şentürk, D.G.; De Backer, A.; Van Aert, S. | ||||
| Title | Element specific atom counting for heterogeneous nanostructures: Combining multiple ADF STEM images for simultaneous thickness and composition determination | Type | A1 Journal Article | ||
| Year |
2024 | Publication | Ultramicroscopy | Abbreviated Journal | Ultramicroscopy |
| Volume | 259 | Issue | Pages | 113941 | |
| Keywords | A1 Journal Article; Electron Microscopy for Materials Science (EMAT) ; | ||||
| Abstract | In this paper, a methodology is presented to count the number of atoms in heterogeneous nanoparticles based on the combination of multiple annular dark field scanning transmission electron microscopy (ADF STEM) images. The different non-overlapping annular detector collection regions are selected based on the principles of optimal statistical experiment design for the atom-counting problem. To count the number of atoms, the total intensities of scattered electrons for each atomic column, the so-called scattering cross-sections, are simultaneously compared with simulated library values for the different detector regions by minimising the squared differences. The performance of the method is evaluated for simulated Ni@Pt and Au@Ag core-shell nanoparticles. Our approach turns out to be a dose efficient alternative for the investigation of beam-sensitive heterogeneous materials as compared to the combination of ADF STEM and energy dispersive X-ray spectroscopy. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-02-19 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0304-3991 | ISBN | Additional Links | ||
| Impact Factor | 2.2 | Times cited | Open Access | OpenAccess | |
| Notes | This work was supported by the European Research Council (Grant 770887 PICOMETRICS to S. Van Aert). The authors acknowledge financial support from the Research Foundation Flanders (FWO, Belgium) through project fundings (G.0346.21N, GOA7723N, and EOS 40007495) and a postdoctoral grant to A. De Backer. S. Van Aert acknowledges funding from the University of Antwerp Research fund (BOF). | Approved | Most recent IF: 2.2; 2024 IF: 2.843 | ||
| Call Number | EMAT @ emat @ | Serial | 8996 | ||
| Permanent link to this record | |||||
| Author | Kashiwar, A.; Arseenko, M.; Simar, A.; Idrissi, H. | ||||
| Title | On the role of microstructural defects on precipitation, damage, and healing behavior in a novel Al-0.5Mg2Si alloy | Type | A1 Journal article | ||
| Year |
2024 | Publication | Materials & design | Abbreviated Journal | |
| Volume | 239 | Issue | Pages | 112765-112769 | |
| Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
| Abstract | A recently developed healable Al-Mg2Si designed by the programmed damage and repair (PDR) strategy is studied considering the role microstructural defects play on precipitation, damage, and healing. The alloy incorporates sacrificial Mg2Si particles that precipitate after friction stir processing (FSP). They act as damage localization sites and are healable based on the solid-state diffusion of Al-matrix. A combination of different transmission electron microscopy (TEM) imaging techniques enabled the visualization and quantification of various crystallographic defects and the spatial distribution of Mg2Si precipitates. Intragrain nucleation is found to be the dominant mechanism for precipitation during FSP whereas grain boundaries and subgrain boundaries mainly lead to coarsening of the precipitates. The statistical and spatial analyses of the damaged particles have shown particle fracture as the dominant damage mechanism which is strongly dependent on the size and aspect ratio of the particles whereas the damage was not found to depend on the location of the precipitates within the matrix. The damaged particles are associated with dislocations accumulated around them. The interplay of these dislocations is directly visualized during healing based on in situ TEM heating which revealed recovery in the matrix as an operative mechanism during the diffusion healing of the PDR alloy. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-02-17 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0264-1275; 1873-4197 | ISBN | Additional Links | UA library record | |
| Impact Factor | 8.4 | Times cited | Open Access | Not_Open_Access | |
| Notes | Approved | Most recent IF: 8.4; 2024 IF: 4.364 | |||
| Call Number | UA @ admin @ c:irua:203298 | Serial | 9068 | ||
| Permanent link to this record | |||||
| Author | Vermeulen, B.B.; Raymenants, E.; Pham, V.T.; Pizzini, S.; Sorée, B.; Wostyn, K.; Couet, S.; Nguyen, V.D.; Temst, K. | ||||
| Title | Towards fully electrically controlled domain-wall logic | Type | A1 Journal article | ||
| Year |
2024 | Publication | AIP advances | Abbreviated Journal | |
| Volume | 14 | Issue | 2 | Pages | 025030-25035 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT) | ||||
| Abstract | Utilizing magnetic tunnel junctions (MTJs) for write/read and fast spin-orbit-torque (SOT)-driven domain-wall (DW) motion for propagation, enables non-volatile logic and majority operations, representing a breakthrough in the implementation of nanoscale DW logic devices. Recently, current-driven DW logic gates have been demonstrated via magnetic imaging, where the Dzyaloshinskii-Moriya interaction (DMI) induces chiral coupling between perpendicular magnetic anisotropy (PMA) regions via an in-plane (IP) oriented region. However, full electrical operation of nanoscale DW logic requires electrical write/read operations and a method to pattern PMA and IP regions compatible with the fabrication of PMA MTJs. Here, we study the use of a Hybrid Free Layer (HFL) concept to combine an MTJ stack with DW motion materials, and He+ ion irradiation to convert the stack from PMA to IP. First, we investigate the free layer thickness dependence of 100-nm diameter HFL-MTJ devices and find an optimal CoFeB thickness, from 7 to 10 angstrom, providing high tunneling magnetoresistance (TMR) readout and efficient spin-transfer torque (STT) writing. We then show that high DMI materials, like Pt/Co, can be integrated into an MTJ stack via interlayer exchange coupling with the CoFeB free layer. In this design, DMI values suitable for SOT-driven DW motion are measured by asymmetric bubble expansion. Finally, we demonstrate that He+ irradiation reliably converts the coupled free layers from PMA to IP. These findings offer a path toward the integration of fully electrically controlled DW logic circuits. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 001163573400005 | Publication Date | 2024-02-16 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2158-3226 | ISBN | Additional Links | UA library record; WoS full record | |
| Impact Factor | Times cited | Open Access | Not_Open_Access | ||
| Notes | Approved | Most recent IF: NA | |||
| Call Number | UA @ admin @ c:irua:203823 | Serial | 9109 | ||
| Permanent link to this record | |||||
| Author | Peeters, H.; Raes, A.; Verbruggen, S.W. | ||||
| Title | Plasmonic photocatalytic coatings with self-cleaning, antibacterial, air and water purifying properties tested according to ISO standards | Type | A1 Journal article | ||
| Year |
2024 | Publication | Journal of photochemistry and photobiology: A: chemistry | Abbreviated Journal | |
| Volume | 451 | Issue | Pages | 115529-10 | |
| Keywords | A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) | ||||
| Abstract | ISO 10678:2010, ISO 22197–1 and 2, ISO 27447:2019 and ISO 27448:2009 for the photocatalytic degradation of organic dyes (methylene blue), air pollution (NOx and acetaldehyde), bacteria (E. coli and S. aureus) and solid organic fouling (oleic acid) are performed on plasmon-embedded TiO2 thin films on Borofloat® glass, as well as the commercially available titania-based self-cleaning glass PilkingtonActivTM. These standardised protocols measure the performance for the four main applications of photocatalytic materials: water purification, air purification, antibacterial and self-cleaning activity, respectively. The standards are performed exactly as prescribed to measure the activity under UV irradiation, and also in a slightly adapted manner to measure the performance under simulated solar light or visible light. Performing experiments according to ISO standards, enables an objective comparison amongst samples tested here, as well as with results from literature. This is a major asset compared to the myriad of customised setups used in laboratories worldwide that hinder a fair comparison. We point at the importance of meticulously following the ISO instructions, as we have noticed that multiple published studies adopting the ISO standards too often deviate from these protocols, thereby nullifying the added value of standardized testing. Following the ISO tests to the letter, we have demonstrated the superior performance of a previously developed plasmonic titania coating with fully embedded gold-silver nanoparticles towards all four application areas. Furthermore, our empirical data strongly support the need for a nuanced understanding of standardized testing, to ensure accurate assessment of photocatalytic materials. An examination of the ISO standards used in this work reveals notable drawbacks, including concerns about the reliability of the methylene blue degradation protocol, the issues of HNO3 accumulation in the NOx removal test, and limitations in assessing antibacterial activity and water contact angles. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-02-15 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1010-6030 | ISBN | Additional Links | UA library record | |
| Impact Factor | 4.3 | Times cited | Open Access | Not_Open_Access | |
| Notes | Approved | Most recent IF: 4.3; 2024 IF: 2.625 | |||
| Call Number | UA @ admin @ c:irua:203203 | Serial | 9075 | ||
| Permanent link to this record | |||||
| Author | Parrilla, M.; Sena-Torralba, A.; Steijlen, A.; Morais, S.; Maquieira, Á.; De Wael, K. | ||||
| Title | A 3D-printed hollow microneedle-based electrochemical sensing device for in situ plant health monitoring | Type | A1 Journal article | ||
| Year |
2024 | Publication | Biosensors and bioelectronics | Abbreviated Journal | |
| Volume | 251 | Issue | Pages | 116131-116139 | |
| Keywords | A1 Journal article; Engineering sciences. Technology; Antwerp Electrochemical and Analytical Sciences Lab (A-Sense Lab) | ||||
| Abstract | Plant health monitoring is devised as a new concept to elucidate in situ physiological processes. The need for increased food production to nourish the growing global population is inconsistent with the dramatic impact of climate change, which hinders crop health and exacerbates plant stress. In this context, wearable sensors play a crucial role in assessing plant stress. Herein, we present a low-cost 3D-printed hollow microneedle array (HMA) patch as a sampling device coupled with biosensors based on screen-printing technology, leading to affordable analysis of biomarkers in the plant fluid of a leaf. First, a refinement of the 3D-printing method showed a tip diameter of 25.9 ± 3.7 μm with a side hole diameter on the microneedle of 228.2 ± 18.6 μm using an affordable 3D printer (<500 EUR). Notably, the HMA patch withstanded the forces exerted by thumb pressing (i.e. 20-40 N). Subsequently, the holes of the HMA enabled the fluid extraction tested in vitro and in vivo in plant leaves (i.e. 13.5 ± 1.1 μL). A paper-based sampling strategy adapted to the HMA allowed the collection of plant fluid. Finally, integrating the sampling device onto biosensors facilitated the in situ electrochemical analysis of plant health biomarkers (i.e. H2O2, glucose, and pH) and the electrochemical profiling of plants in five plant species. Overall, this electrochemical platform advances precise and versatile sensors for plant health monitoring. The wearable device can potentially improve precision farming practices, addressing the critical need for sustainable and resilient agriculture in changing environmental conditions. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-02-13 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0956-5663 | ISBN | Additional Links | UA library record | |
| Impact Factor | 12.6 | Times cited | Open Access | Not_Open_Access | |
| Notes | Approved | Most recent IF: 12.6; 2024 IF: 7.78 | |||
| Call Number | UA @ admin @ c:irua:203204 | Serial | 8998 | ||
| Permanent link to this record | |||||
| Author | Jorissen, B.; Covaci, L.; Partoens, B. | ||||
| Title | Comparative analysis of tight-binding models for transition metal dichalcogenides | Type | A1 Journal article | ||
| Year |
2024 | Publication | SciPost physics core | Abbreviated Journal | |
| Volume | 7 | Issue | 1 | Pages | 004-30 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT); Condensed Matter Theory (CMT) | ||||
| Abstract | We provide a comprehensive analysis of the prominent tight-binding (TB) models for transition metal dichalcogenides (TMDs) available in the literature. We inspect the construction of these TB models, discuss their parameterization used and conduct a thorough comparison of their effectiveness in capturing important electronic properties. Based on these insights, we propose a novel TB model for TMDs designed for enhanced computational efficiency. Utilizing MoS2 as a representative case, we explain why specific models offer a more accurate description. Our primary aim is to assist researchers in choosing the most appropriate TB model for their calculations on TMDs. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-02-06 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | ISBN | Additional Links | UA library record | ||
| Impact Factor | Times cited | Open Access | Not_Open_Access | ||
| Notes | Approved | Most recent IF: NA | |||
| Call Number | UA @ admin @ c:irua:202983 | Serial | 9012 | ||
| Permanent link to this record | |||||
| Author | Manaigo, F.; Rouwenhorst, K.; Bogaerts, A.; Snyders, R. | ||||
| Title | Feasibility study of a small-scale fertilizer production facility based on plasma nitrogen fixation | Type | A1 Journal Article | ||
| Year |
2024 | Publication | Energy Conversion and Management | Abbreviated Journal | Energy Conversion and Management |
| Volume | 302 | Issue | Pages | 118124 | |
| Keywords | A1 Journal Article; Plasma-based nitrogen fixation Haber-Bosch Feasibility study Fertilizer production; Plasma, laser ablation and surface modeling Antwerp (PLASMANT) ; | ||||
| Abstract | |||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-01-25 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0196-8904 | ISBN | Additional Links | ||
| Impact Factor | 10.4 | Times cited | Open Access | Not_Open_Access | |
| Notes | This research is supported by the FNRS-FWO project ‘‘NITROPLASM’’, EOS O005118F. The authors thank Dr. L. Hollevoet (KU Leuven) for the draft reviewing and for providing additional information on the lean NO???? trap. | Approved | Most recent IF: 10.4; 2024 IF: 5.589 | ||
| Call Number | PLASMANT @ plasmant @ | Serial | 8992 | ||
| Permanent link to this record | |||||
| Author | Minja, A.C.; Ag, K.R.; Raes, A.; Borah, R.; Verbruggen, S.W. | ||||
| Title | Recent progress in developing non-noble metal-based photocathodes for solar green hydrogen production | Type | A1 Journal article | ||
| Year |
2024 | Publication | Current Opinion in Chemical Engineering | Abbreviated Journal | |
| Volume | 43 | Issue | Pages | 101000 | |
| Keywords | A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) | ||||
| Abstract | Photocathodes play a vital role in photoelectrocatalytic water splitting by acting as catalysts for reducing protons to hydrogen gas when exposed to light. Recent advancements in photocathodes have focused on addressing the limitations of noble metal-based materials. These noble metal-based photocathodes rely on expensive and scarce metals such as platinum and gold as cocatalysts or ohmic back contacts, respectively, rendering the final system less sustainable and costly when applied at scale. This mini-review summarizes the important recent progress in the development of non-noble metal-based photocathodes and their performance in the hydrogen evolution reaction during photoelectrochemical (PEC) water splitting. These advancements bring non-noble metal-based photocathodes closer to their noble metal-based counterparts in terms of performance, thereby paving the way forward toward industrial-scale photoelectrolyzers or PEC cells for green hydrogen production. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | 2024-01-20 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2211-3398 | ISBN | Additional Links | UA library record | |
| Impact Factor | 6.6 | Times cited | Open Access | Not_Open_Access | |
| Notes | Approved | Most recent IF: 6.6; 2024 IF: 3.403 | |||
| Call Number | UA @ admin @ c:irua:202625 | Serial | 9080 | ||
| Permanent link to this record | |||||