|
Records |
|
Author |
Zhang, H.; Gauquelin, N.; McMahon, C.; Hawthorn, D.G.; Botton, G.A.; Wei, J.Y.T. |
|
Title |
Synthesis of high-oxidation Y-Ba-Cu-O phases in superoxygenated thin films |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Physical review materials |
Abbreviated Journal |
|
|
Volume |
2 |
Issue |
3 |
Pages |
033803 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
It is known that solid-state reaction in high-pressure oxygen can stabilize high-oxidation phases of Y-Ba-Cu-O superconductors in powder form. We extend this superoxygenation concept of synthesis to thin films which, due to their large surface-to-volume ratio, are more reactive thermodynamically. Epitaxial thin films of YBa2Cu3O7-delta grown by pulsed laser deposition are annealed at up to 700 atm O-2 and 900 degrees C, in conjunction with Cu enrichment by solid-state diffusion. The films show the clear formation of Y2Ba4Cu7O15-delta and Y2Ba4Cu8O16 as well as regions of YBa2Cu5O9-delta and YBa2Cu6O10-delta phases, according to scanning transmission electron microscopy, x-ray diffraction, and x-ray absorption spectroscopy. Similarly annealed YBa2Cu3O7-delta powders show no phase conversion. Our results demonstrate a route of synthesis towards discovering more complex phases of cuprates and other superconducting oxides. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
American Physical Society |
Place of Publication |
College Park, Md |
Editor |
|
|
Language |
|
Wos |
000428244900004 |
Publication Date |
2018-03-26 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2475-9953 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
|
Times cited |
2 |
Open Access |
Not_Open_Access |
|
Notes |
; This work is supported by NSERC, CFI-OIT, and CIFAR. The electron microscopy work was carried out at the Canadian Centre for Electron Microscopy, a National Facility supported by the Canada Foundation for Innovation under the Major Science Initiative program, McMaster University, and NSERC. The XAS work was performed at the Canadian Light Source, which is supported by NSERC, NRC, CIHR, and the University of Saskatchewan. ; |
Approved |
Most recent IF: NA |
|
Call Number |
UA @ lucian @ c:irua:150829 |
Serial |
4982 |
Permanent link to this record |
|
|
|
|
Author |
Rizzo, F.; Augieri, A.; Kursumovic, A.; Bianchetti, M.; Opherden, L.; Sieger, M.; Huehne, R.; Haenisch, J.; Meledin, A.; Van Tendeloo, G.; MacManus-Driscoll, J.L.; Celentano, G. |
|
Title |
Pushing the limits of applicability of REBCO coated conductor films through fine chemical tuning and nanoengineering of inclusions |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Nanoscale |
Abbreviated Journal |
Nanoscale |
|
Volume |
10 |
Issue |
17 |
Pages |
8187-8195 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
An outstanding current carrying performance (namely critical current density, J(c)) over a broad temperature range of 10-77 K for magnetic fields up to 12 T is reported for films of YBa2Cu3O7-x with Ba2Y(Nb,Ta)O-6 inclusion pinning centres (YBCO-BYNTO) and thicknesses in the range of 220-500 nm. J(c) values of 10 MA cm(-2) were measured at 30 K – 5 T and 10 K – 9 T with a corresponding maximum of the pinning force density at 10 K close to 1 TN m(-3). The system is very flexible regarding properties and microstructure tuning, and the growth window for achieving a particular microstructure is wide, which is very important for industrial processing. Hence, the dependence of J(c) on the magnetic field angle was readily controlled by fine tuning the pinning microstructure. Transmission electron microscopy (TEM) analysis highlighted that higher growth rates induce more splayed and denser BYNTO nanocolumns with a matching field as high as 5.2 T. Correspondingly, a strong peak at the B||c-axis is noticed when the density of vortices is lower than the nanocolumn density. YBCO-BYNTO is a very robust and reproducible composite system for high-current coated conductors over an extended range of magnetic fields and temperatures. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Cambridge |
Editor |
|
|
Language |
|
Wos |
000432261400037 |
Publication Date |
2018-03-26 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2040-3364 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
7.367 |
Times cited |
9 |
Open Access |
OpenAccess |
|
Notes |
; This work was partially financially supported by EUROTAPES, a collaborative project funded by the European Commission's Seventh Framework Program (FP7/ 2007-2013) under Grant Agreement No. 280432. This work has been partially carried out within the framework of the EUROfusion Consortium and has received funding from the Euratom research and training programme 2014-2018 under grant agreement no. 633053. The views and opinions expressed herein do not necessarily reflect those of the European Commission. ; |
Approved |
Most recent IF: 7.367 |
|
Call Number |
UA @ lucian @ c:irua:151520 |
Serial |
5038 |
Permanent link to this record |
|
|
|
|
Author |
Quintanilla, M.; Zhang, Y.; Liz-Marzan, L.M. |
|
Title |
Subtissue plasmonic heating monitored with CaF2:Nd3+,Y3+ nanothermometers in the second biological window |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Chemistry of materials |
Abbreviated Journal |
Chem Mater |
|
Volume |
30 |
Issue |
8 |
Pages |
2819-2828 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Measuring temperature in biological environments is an ambitious goal toward supporting medical treatment and diagnosis. Minimally invasive techniques based on optical probes require very specific properties that are difficult to combine within a single material. These include high chemical stability in aqueous environments, optical signal stability, low toxicity, high emission intensity, and, essential, working at wavelengths within the biological transparency windows so as to minimize invasiveness while maximizing penetration depth. We propose CaF2:Nd3+,Y3+ as a candidate for thermometry based on an intraband ratiometric approach, fully working within the biological windows (excitation at 808 nm; emission around 1050 nm). We optimized the thermal probes through the addition of Y3+ as a dopant to improve both emission intensity and thermal sensitivity. To define the conditions under which the proposed technique can be applied, gold nanorods were used to optically generate subtissue hot areas, while the resulting temperature variation was monitored with the new nanothermometers. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
American Chemical Society |
Place of Publication |
Washington, D.C |
Editor |
|
|
Language |
|
Wos |
000431088400038 |
Publication Date |
2018-03-27 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0897-4756 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
9.466 |
Times cited |
28 |
Open Access |
Not_Open_Access |
|
Notes |
; The authors would like to thank Dr. Guillermo Gonzalez Rubio for the kind support with the synthesis of gold nanorods. M.Q and L.M.L.-M. acknowledge financial support from the European Commission under the Marie Sklodowska-Curie program (H2020-MSCA-IF-2014_659021 – PHELLINI). Y.Z. acknowledges financial support from the European Union's Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie Grant Agreement No. 665501 through a FWO [PEGASUS]^2 Marie Sklodowska-Curie fellowship (12U4917N). ; |
Approved |
Most recent IF: 9.466 |
|
Call Number |
UA @ lucian @ c:irua:151576 |
Serial |
5042 |
Permanent link to this record |
|
|
|
|
Author |
Alexander, C.T.; Abakumov, A.M.; Forslund, R.P.; Johnston, K.P.; Stevenson, K.J. |
|
Title |
Role of the carbon support on the oxygen reduction and evolution activities in LaNiO3 composite electrodes in alkaline solution |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
ACS applied energy materials |
Abbreviated Journal |
|
|
Volume |
1 |
Issue |
4 |
Pages |
1549-1558 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Metal-air batteries and fuel cells show a great deal of promise in advancing low-cost, high-energy-density charge storage solutions for sustainable energy applications. To improve the activities and stabilities of electrocatalysts for the critical oxygen reduction and evolution reactions (ORR and OER, respectively), a greater understanding is needed of the catalyst/carbon interactions and carbon stability. Herein, we report how LaNiO3 (LNO) supported on nitrogen-doped carbon nanotubes (N-CNT) made from a high-yield synthesis lowers the overpotential for both the OER and ORR markedly to enable a low bifunctional window of 0.81 V at only a 51 mu g cm(-2) mass loading. Furthermore, the addition of LNO to the N-CNTs improves the galvanostatic stability for the OER by almost 2 orders of magnitude. The nanoscale geometries of the perovskites and the CNTs enhance the number of metal-support and charge transfer interactions and thus the activity. We use rotating ring disk electrodes (RRDEs) combined with Tafel slope analysis and ICP-OES to quantitatively separate current contributions from the OER, carbon oxidation, and even anodic iron leaching from carbon nanotubes. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000458705400020 |
Publication Date |
2018-03-28 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2574-0962 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
|
Times cited |
|
Open Access |
|
|
Notes |
|
Approved |
no |
|
Call Number |
UA @ admin @ c:irua:157642 |
Serial |
8487 |
Permanent link to this record |
|
|
|
|
Author |
Xia, C.; Winckelmans, N.; Prins, P.T.; Bals, S.; Gerritsen, H.C.; de Mello Donegá, C. |
|
Title |
Near-Infrared-Emitting CuInS2/ZnS Dot-in-Rod Colloidal Heteronanorods by Seeded Growth |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Journal of the American Chemical Society |
Abbreviated Journal |
J Am Chem Soc |
|
Volume |
140 |
Issue |
140 |
Pages |
5755-5763 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Synthesis protocols for anisotropic CuInX2 (X = S, Se, Te)-based heteronanocrystals (HNCs) are scarce due to the difficulty in balancing the reactivities of multiple precursors and the high solid-state diffusion rates of the cations involved in the CuInX2 lattice. In this work, we report a multistep seeded growth synthesis protocol that yields colloidal wurtzite CuInS2/ZnS dot core/rod shell HNCs with photoluminescence in the NIR (∼800 nm). The wurtzite CuInS2 NCs used as seeds are obtained by topotactic partial Cu+ for In3+ cation exchange in template Cu2–xS NCs. The seed NCs are injected in a hot solution of zinc oleate and hexadecylamine in octadecene, 20 s after the injection of sulfur in octadecene. This results in heteroepitaxial growth of wurtzite ZnS primarily on the Sulfur-terminated polar facet of the CuInS2 seed NCs, the other facets being overcoated only by a thin (∼1 monolayer) shell. The fast (∼21 nm/min) asymmetric axial growth of the nanorod proceeds by addition of [ZnS] monomer units, so that the polarity of the terminal (002) facet is preserved throughout the growth. The delayed injection of the CuInS2 seed NCs is crucial to allow the concentration of [ZnS] monomers to build up, thereby maximizing the anisotropic heteroepitaxial growth rates while minimizing the rates of competing processes (etching, cation exchange, alloying). Nevertheless, a mild etching still occurred, likely prior to the onset of heteroepitaxial overgrowth, shrinking the core size from 5.5 to ∼4 nm. The insights provided by this work open up new possibilities in designing multifunctional Cu-chalcogenide based colloidal heteronanocrystals. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000431600000016 |
Publication Date |
2018-03-29 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0002-7863 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
13.858 |
Times cited |
43 |
Open Access |
OpenAccess |
|
Notes |
Chenghui Xia acknowledges China Scholarship Council (CSC) for financial support (NO. 201406330055). S.B and N.W. acknowledge funding from the European Research Council (Starting Grant No. COLOURATOMS 335078). C.d.M.D. acknowledge financial support from the division of Chemical Sciences (CW) of The Netherlands Organization for Scientific Research (NWO) under Grant Number ECHO.712.014.001. The authors thank Xiaobin Xie and Da Wang for some TEM measurements, Donglong Fu for XRD measurements, Christina H. M. van Oversteeg for ICP-OES measurements, and Chun-Che Lin for suggestions regarding the synthesis. ECAS_Sara (ROMEO:white; preprint:; postprint:restricted 12 months embargo; pdfversion:cannot); |
Approved |
Most recent IF: 13.858 |
|
Call Number |
EMAT @ emat @c:irua:150362UA @ admin @ c:irua:150362 |
Serial |
4917 |
Permanent link to this record |
|
|
|
|
Author |
Korneychuk, S.; Partoens, B.; Guzzinati, G.; Ramaneti, R.; Derluyn, J.; Haenen, K.; Verbeeck, J. |
|
Title |
Exploring possibilities of band gap measurement with off-axis EELS in TEM |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Ultramicroscopy |
Abbreviated Journal |
Ultramicroscopy |
|
Volume |
189 |
Issue |
189 |
Pages |
76-84 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT); Condensed Matter Theory (CMT) |
|
Abstract |
A technique to measure the band gap of dielectric materials with high refractive index by means of energy electron loss spectroscopy (EELS) is presented. The technique relies on the use of a circular (Bessel) aperture and suppresses Cherenkov losses and surface-guided light modes by enforcing a momentum transfer selection. The technique also strongly suppresses the elastic zero loss peak, making the acquisition, interpretation and signal to noise ratio of low loss spectra considerably better, especially for excitations in the first few eV of the EELS spectrum. Simulations of the low loss inelastic electron scattering probabilities demonstrate the beneficial influence of the Bessel aperture in this setup even for high accelerating voltages. The importance of selecting the optimal experimental convergence and collection angles is highlighted. The effect of the created off-axis acquisition conditions on the selection of the transitions from valence to conduction bands is discussed in detail on a simplified isotropic two band model. This opens the opportunity for deliberately selecting certain transitions by carefully tuning the microscope parameters. The suggested approach is experimentally demonstrated and provides good signal to noise ratio and interpretable band gap signals on reference samples of diamond, GaN and AlN while offering spatial resolution in the nm range. (C) 2018 Elsevier B.V. All rights reserved. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
|
Language |
|
Wos |
000432868500008 |
Publication Date |
2018-03-29 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0304-3991 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
2.843 |
Times cited |
7 |
Open Access |
OpenAccess |
|
Notes |
; S.K., B.P. and J.V. acknowledge funding from the “Geconcentreerde Onderzoekacties” (GOA) project “Solarpaint” of the University of Antwerp. S.K. and J.V. also acknowledge the FWO-Vlaanderen for financial support under contract G.0044.13N 'Charge ordering'. Financial support via the Methusalem “NANO” network is acknowledged. GG acknowledges support from a postdoctoral fellowship grant from the Fonds Wetenschappelijk Onderzoek-Vlaanderen (FWO). ; |
Approved |
Most recent IF: 2.843 |
|
Call Number |
UA @ lucian @ c:irua:151472UA @ admin @ c:irua:151472 |
Serial |
5026 |
Permanent link to this record |
|
|
|
|
Author |
Song, H.-D.; Wu, Y.-F.; Yang, X.; Ren, Z.; Ke, X.; Kurttepeli, M.; Tendeloo, G.V.; Liu, D.; Wu, H.-C.; Yan, B.; Wu, X.; Duan, C.-G.; Han, G.; Liao, Z.-M.; Yu, D. |
|
Title |
Asymmetric Modulation on Exchange Field in a Graphene/BiFeO3Heterostructure by External Magnetic Field |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Nano letters |
Abbreviated Journal |
Nano Lett |
|
Volume |
18 |
Issue |
4 |
Pages |
2435-2441 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
Graphene, having all atoms on its surface, is favorable to extend the functions by introducing the spin–orbit coupling and magnetism through proximity effect. Here, we report the tunable interfacial exchange field produced by proximity coupling in graphene/BiFeO3 heterostructures. The exchange field has a notable dependence with external magnetic field, and it is much larger under negative magnetic field than that under positive magnetic field. For negative external magnetic field, interfacial exchange coupling gives rise to evident spin splitting for N ≠ 0 Landau levels and a quantum Hall metal state for N = 0 Landau level. Our findings suggest graphene/BiFeO3 heterostructures are promising for spintronics. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000430155900034 |
Publication Date |
2018-04-11 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
1530-6984 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
12.712 |
Times cited |
9 |
Open Access |
Not_Open_Access |
|
Notes |
This work was supported by National Key Research and Development Program of China (No. 2016YFA0300802) and NSFC (Nos. 11774004 and 11604004). Ministry of Science and Technology of the People's Republic of China, 2016YFA0300802 ; National Natural Science Foundation of China, 11604004 11774004 ; |
Approved |
Most recent IF: 12.712 |
|
Call Number |
EMAT @ lucian @c:irua:150794 |
Serial |
4923 |
Permanent link to this record |
|
|
|
|
Author |
Grieb, T.; Krause, F.F.; Schowalter, M.; Zillmann, D.; Sellin, R.; Müller-Caspary, K.; Mahr, C.; Mehrtens, T.; Bimberg, D.; Rosenauer, A. |
|
Title |
Strain analysis from nano-beam electron diffraction : influence of specimen tilt and beam convergence |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Ultramicroscopy |
Abbreviated Journal |
Ultramicroscopy |
|
Volume |
190 |
Issue |
190 |
Pages |
45-57 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Strain analyses from experimental series of nano-beam electron diffraction (NBED) patterns in scanning transmission electron microscopy are performed for different specimen tilts. Simulations of NBED series are presented for which strain analysis gives results that are in accordance with experiment. This consequently allows to study the relation between measured strain and actual underlying strain. A two-tilt method which can be seen as lowest-order electron beam precession is suggested and experimentally implemented. Strain determination from NBED series with increasing beam convergence is performed in combination with the experimental realization of a probe-forming aperture with a cross inside. It is shown that using standard evaluation techniques, the influence of beam convergence on spatial resolution is lower than the influence of sharp rings around the diffraction disc which occur at interfaces and which are caused by the tails of the intensity distribution of the electron probe. (C) 2018 Elsevier B.V. All rights reserved. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
|
Language |
|
Wos |
000432868800006 |
Publication Date |
2018-04-12 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0304-3991 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
2.843 |
Times cited |
1 |
Open Access |
OpenAccess |
|
Notes |
; This work was supported by the German Research Foundation (DFG) under Contracts RO2057/11-1 and RO2057/12-1. ; |
Approved |
Most recent IF: 2.843 |
|
Call Number |
UA @ lucian @ c:irua:151454 |
Serial |
5041 |
Permanent link to this record |
|
|
|
|
Author |
Claes, N.; Asapu, R.; Blommaerts, N.; Verbruggen, S.W.; Lenaerts, S.; Bals, S. |
|
Title |
Characterization of silver-polymer core–shell nanoparticles using electron microscopy |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Nanoscale |
Abbreviated Journal |
Nanoscale |
|
Volume |
10 |
Issue |
10 |
Pages |
9186-9191 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Sustainable Energy, Air and Water Technology (DuEL) |
|
Abstract |
Silver-polymer core–shell nanoparticles show interesting optical properties, making them widely applicable in the field of plasmonics. The uniformity, thickness and homogeneity of the polymer shell will affect the properties of the system which makes a thorough structural characterization of these core–shell silver-polymer nanoparticles of great importance. However, visualizing the shell and the particle simultaneously is far from straightforward due to the sensitivity of the polymer shell towards the electron beam. In this study, we use different 2D and 3D electron microscopy techniques to investigate different structural aspects of the polymer coating. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000437007700028 |
Publication Date |
2018-04-16 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2040-3364 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
7.367 |
Times cited |
11 |
Open Access |
OpenAccess |
|
Notes |
N. C. and S. B. acknowledge financial support from European Research Council (ERC Starting Grant #335078-COLOURATOMS) and from the FWO through project funding (G038116N). R. A. and S. L. acknowledge the Research Foundation Flanders (FWO) for financial support. (ROMEO:yellow; preprint:; postprint:restricted ; pdfversion:cannot); ECAS_Sara |
Approved |
Most recent IF: 7.367 |
|
Call Number |
EMAT @ emat @c:irua:151290UA @ admin @ c:irua:151290 |
Serial |
4959 |
Permanent link to this record |
|
|
|
|
Author |
Leus, K.; Folens, K.; Nicomel, N.R.; Perez, J.P.H.; Filippousi, M.; Meledina, M.; Dirtu, M.M.; Turner, S.; Van Tendeloo, G.; Garcia, Y.; Du Laing, G.; Van Der Voort, P. |
|
Title |
Removal of arsenic and mercury species from water by covalent triazine framework encapsulated \gamma-Fe2O3 nanoparticles |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Journal of hazardous materials |
Abbreviated Journal |
J Hazard Mater |
|
Volume |
353 |
Issue |
353 |
Pages |
312-319 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
The covalent triazine framework, CTF-1, served as host material for the in situ synthesis of Fe2O3 nanoparticles. The composite material consisted of 20 +/- 2 m% iron, mainly in gamma-Fe2O3 phase. The resulting gamma-Fe2O3@CTF-1 was examined for the adsorption of As-III, As-V and H-II from synthetic solutions and real surface-, ground- and wastewater. The material shows excellent removal efficiencies, independent from the presence of Ca2+, Mg2+ or natural organic matter and only limited dependency on the presence of phosphate ions. Its adsorption capacity towards arsenite (198.0 mg g(-1)), arsenate (102.3 mg g(-1)) and divalent mercury (165.8 mg g(-1)) belongs amongst the best-known adsorbents, including many other iron-based materials. Regeneration of the adsorbent can be achieved for use over multiple cycles without a decrease in performance by elution at 70 degrees C with 0.1 M NaOH, followed by a stirring step in a 5 m% H2O2 solution for As or 0.1 M thiourea and 0.001 M HCl for Hg. In highly contaminated water (100 mu gL(-1)), the adsorbent polishes the water quality to well below the current WHO limits. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
|
Language |
|
Wos |
000438002800035 |
Publication Date |
2018-04-16 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0304-3894 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
6.065 |
Times cited |
22 |
Open Access |
OpenAccess |
|
Notes |
; Karen Leus acknowledges financial support from Ghent University. Nina Ricci Nicomel and Jeffrey Paulo H. Perez thank the funding of the VLIR-UOS. Marinela M. Dirtu acknowledges F.R.S.-FNRS for a Charge de recherches position. Stuart Turner gratefully acknowledges the FWO Vlaanderen for a post-doctoral scholarship. The Titan microscope used for this investigation was partially funded by the Hercules foundation of the Flemish government. This work was supported by the Belgian IAP-PAI network. ; |
Approved |
Most recent IF: 6.065 |
|
Call Number |
UA @ lucian @ c:irua:152430 |
Serial |
5124 |
Permanent link to this record |
|
|
|
|
Author |
Verbeeck, J.; Béché, A.; Müller-Caspary, K.; Guzzinati, G.; Luong, M.A.; Den Hertog, M. |
|
Title |
Demonstration of a 2 × 2 programmable phase plate for electrons |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Ultramicroscopy |
Abbreviated Journal |
Ultramicroscopy |
|
Volume |
190 |
Issue |
|
Pages |
58-65 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
First results on the experimental realisation of a 2 × 2 programmable phase plate for electrons are presented. The design consists of an array of electrostatic elements that influence the phase of electron waves passing through 4 separately controllable aperture holes. This functionality is demonstrated in a conventional transmission electron microscope operating at 300 kV and results are in very close agreement with theoretical predictions. The dynamic creation of a set of electron probes with different phase symmetry is demonstrated, thereby bringing adaptive optics in TEM one step closer to reality. The limitations of the current design and how to overcome these in the future are discussed. Simulations show how further evolved versions of the current proof of concept might open new and exciting application prospects for beam shaping and aberration correction. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000432868800007 |
Publication Date |
2018-04-18 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0304-3991 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
2.843 |
Times cited |
73 |
Open Access |
Not_Open_Access: Available from 19.04.2020
|
|
Notes |
J.V. and A.B. acknowledge funding from the Fund for Scientific Research Flanders FWO project G093417N and the European Research Council under the 7th Framework Program (FP7), ERC Starting Grant 278510 VORTEX and ERC proof of concept project DLV-789598 ADAPTEM. The Qu-Ant-EM microscope used in this work was partly funded by the Hercules fund from the Flemish Government. MdH acknowledges financial support from the ANRCOSMOS (ANR-12-JS10-0002). MdH and ML acknowledge funding from the Laboratoire d’excellence LANEF in Grenoble (ANR-10-LABX-51-01). |
Approved |
Most recent IF: 2.843 |
|
Call Number |
EMAT @ emat @c:irua:150459UA @ admin @ c:irua:150459 |
Serial |
4920 |
Permanent link to this record |
|
|
|
|
Author |
Cautaerts, N.; Delville, R.; Stergar, E.; Schryvers, D.; Verwerft, M. |
|
Title |
Tailoring the Ti-C nanoprecipitate population and microstructure of titanium stabilized austenitic steels |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Journal of nuclear materials |
Abbreviated Journal |
J Nucl Mater |
|
Volume |
507 |
Issue |
507 |
Pages |
177-187 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
The present work reports on the microstructural evolution of a new heat of 24% cold worked austenitic DIN 1.4970 (15-15Ti) nuclear cladding steel subjected to ageing heat treatments of varying duration between 500 and 800 degrees C (by steps of 100 degrees C). The primary aim was studying the finely dispersed Ti-C nanoprecipitate population, which are thought to be beneficial for creep and swelling resistance during service. Their size distribution and number density were estimated through dark field imaging and bright field Moire imaging techniques in the transmission electron microscope. Nanoprecipitates formed at and above 600 degrees C, which is a lower temperature than previously reported. The observed nucleation, growth and coarsening behavior of the nanoprecipitates were consistent with simple diffusion arguments. The formation of nanoprecipitates coincided with significant dissociation of dislocations as evidenced by weak beam dark field imaging. Possible mechanisms, including Silcock's stacking fault growth model and Suzuki segregation, are discussed. Recrystallization observed after extended ageing at 800 degrees C caused the redissolution of nanoprecipitates. Large primary Ti(C,N) and (Ti,Mo)C precipitates that occur in the as-received material, and M23C6 precipitates that nucleate on grain boundaries at low temperatures were also characterized by a selective dissolution procedure involving filtration, X-ray diffraction and quantitative Rietveld refinement. The partitioning of key elements between the different phases was derived by combining these findings and was consistent with thermodynamic considerations and the processing history of the steel. (C) 2018 Elsevier B.V. All rights reserved. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
|
Language |
|
Wos |
000438019800021 |
Publication Date |
2018-04-30 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0022-3115 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
2.048 |
Times cited |
1 |
Open Access |
Not_Open_Access |
|
Notes |
; We would like to acknowledge ENGIE, SCK.CEN, the SCK.CEN academy and the MYRRHA project for the financial support of this work. Special thanks to T. Wangle and P. Dries for their help with filtration and gravimetry. Also thanks to Dr. G. Leinders for the discussions on XRD and Rietveld refinement. Thanks to E. Charalampopoulou and A. Youssef for assisting with the dissolution experiments. ; |
Approved |
Most recent IF: 2.048 |
|
Call Number |
UA @ lucian @ c:irua:152382 |
Serial |
5043 |
Permanent link to this record |
|
|
|
|
Author |
Vishwakarma, M.; Thota, N.; Karakulina, O.; Hadermann, J.; Mehta, B.R. |
|
Title |
Role of graphene inter layer on the formation of the MoS2 – CZTS interface during growth |
Type |
P1 Proceeding |
|
Year |
2018 |
Publication |
(icc-2017) |
Abbreviated Journal |
|
|
Volume |
|
Issue |
|
Pages |
|
|
Keywords |
P1 Proceeding; Electron microscopy for materials research (EMAT) |
|
Abstract |
The growth of MoS2 layer near the Mo/CZTS interface during sulphurization process can have an impact on back contact cell parameters (series resistance and fill factor) depending upon the thickness or quality of MoS2. This study reports the dependence of the thickness of interfacial MoS2 layer on the growth of graphene at the interface between molybdenum back contact and deposited CZTS layer. The graphene layer reduces the accumulation of Zn/ZnS, Sn/SnO2 and formation of pores near the MoS2-CZTS interface. The use of graphene as interface layer can be potentially useful for improving the quality of Mo/MoS2/CZTS interface. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
Amer inst physics |
Place of Publication |
Melville |
Editor |
|
|
Language |
|
Wos |
000436313003046 |
Publication Date |
2018-05-09 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
1953 |
Series Issue |
|
Edition |
|
|
ISSN |
978-0-7354-1648-2; 0094-243x; 0094-243x |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
|
Times cited |
1 |
Open Access |
OpenAccess |
|
Notes |
; The authors acknowledge support provided by DST project. M.V. acknowledges IIT Delhi for MHRD fellowship. Prof. B. R. Mehta acknowledges the support of the Schlumberger chair professorship. ; |
Approved |
Most recent IF: NA |
|
Call Number |
UA @ lucian @ c:irua:153203 |
Serial |
5126 |
Permanent link to this record |
|
|
|
|
Author |
Gauquelin, N.; Zhang, H.; Zhu, G.; Wei, J.Y.T.; Botton, G.A. |
|
Title |
Atomic-scale identification of novel planar defect phases in heteroepitaxial YBa2Cu3O7-\delta thin films |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
AIP advances |
Abbreviated Journal |
Aip Adv |
|
Volume |
8 |
Issue |
5 |
Pages |
055022 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
We have discovered two novel types of planar defects that appear in heteroepitaxial YBa2Cu3O7-delta(YBCO123) thin films, grown by pulsed-laser deposition (PLD) either with or without a La2/3Ca1/3MnO3 (LCMO) overlayer, using the combination of highangle annular dark-field scanning transmission electron microscopy (HAADF-STEM) imaging and electron energy loss spectroscopy (EELS) mapping for unambiguous identification. These planar lattice defects are based on the intergrowth of either a BaO plane between two CuO chains or multiple Y-O layers between two CuO2 planes, resulting in non-stoichiometric layer sequences that could directly impact the high-Tc superconductivity. (C) 2018 Author(s). |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
American Institute of Physics |
Place of Publication |
Melville, NY |
Editor |
|
|
Language |
|
Wos |
000433954000022 |
Publication Date |
2018-05-21 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2158-3226 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
1.568 |
Times cited |
1 |
Open Access |
OpenAccess |
|
Notes |
; We are thankful to Julia Huang for FIB TEM sample preparation. This work is supported by NSERC (through Discovery Grants to GAB and JYTW) and CIFAR. The electron microscopy work was carried out at the Canadian Centre for Electron Microscopy, a National Facility supported by McMaster University, the Canada Foundation for Innovation and NSERC. N.G. acknowledges H. Idrissi for useful discussions. ; |
Approved |
Most recent IF: 1.568 |
|
Call Number |
UA @ lucian @ c:irua:152063 |
Serial |
5013 |
Permanent link to this record |
|
|
|
|
Author |
Grimaud, A.; Iadecola, A.; Batuk, D.; Saubanere, M.; Abakumov, A.M.; Freeland, J.W.; Cabana, J.; Li, H.; Doublet, M.-L.; Rousse, G.; Tarascon, J.-M. |
|
Title |
Chemical activity of the peroxide/oxide redox couple : case study of Ba5Ru2O11 in aqueous and organic solvents |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Chemistry of materials |
Abbreviated Journal |
Chem Mater |
|
Volume |
30 |
Issue |
11 |
Pages |
3882-3893 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
The finding that triggering the redox activity of oxygen ions within the lattice of transition metal oxides can boost the performances of materials used in energy storage and conversion devices such as Li-ion batteries or oxygen evolution electrocatalysts has recently spurred intensive and innovative research in the field of energy. While experimental and theoretical efforts have been critical in understanding the role of oxygen nonbonding states in the redox activity of oxygen ions, a clear picture of the redox chemistry of the oxygen species formed upon this oxidation process is still missing. This can be, in part, explained by the complexity in stabilizing and studying these species once electrochemically formed. In this work, we alleviate this difficulty by studying the phase Ba5Ru2O11, which contains peroxide O-2(2-) groups, as oxygen evolution reaction electrocatalyst and Li-ion battery material. Combining physical characterization and electrochemical measurements, we demonstrate that peroxide groups can easily be oxidized at relatively low potential, leading to the formation of gaseous dioxygen and to the instability of the oxide. Furthermore, we demonstrate that, owing to the stabilization at high energy of peroxide, the high-lying energy of the empty sigma* antibonding O-O states limits the reversibility of the electrochemical reactions when the O-2(2-)/O2- redox couple is used as redox center for Li-ion battery materials or as OER redox active sites. Overall, this work suggests that the formation of true peroxide O-2(2-) states are detrimental for transition metal oxides used as OER catalysts and Li-ion battery materials. Rather, oxygen species with O-O bond order lower than 1 would be preferred for these applications. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
American Chemical Society |
Place of Publication |
Washington, D.C |
Editor |
|
|
Language |
|
Wos |
000435416600038 |
Publication Date |
2018-05-21 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0897-4756 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
9.466 |
Times cited |
2 |
Open Access |
Not_Open_Access |
|
Notes |
; We thank S. Belin of the ROCK beamline (financed by the French National Research Agency (ANR) as a part of the “Investissements d'Avenir” program, reference: ANR-10-EQPX-45; proposal no. 20160095) of synchrotron SOLEIL for her assistance during XAS measurements. Authors would also like to thank V. Nassif for her assistance on the D1B beamline. A.G, G.R, and J.-M.T. acknowledge funding from the European Research Council (ERC) (FP/2014)/ERC Grant Project 670116-ARPEMA. ; |
Approved |
Most recent IF: 9.466 |
|
Call Number |
UA @ lucian @ c:irua:151980 |
Serial |
5016 |
Permanent link to this record |
|
|
|
|
Author |
Pearce, P.E.; Rousse, G.; Karakulina, O.M.; Hadermann, J.; Van Tendeloo, G.; Foix, D.; Fauth, F.; Abakumov, A.M.; Tarascon, J.-M. |
|
Title |
β-Na1.7IrO3: A Tridimensional Na-Ion Insertion Material with a Redox Active Oxygen Network |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Chemistry of materials |
Abbreviated Journal |
Chem Mater |
|
Volume |
30 |
Issue |
10 |
Pages |
3285-3293 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
The revival of the Na-ion battery concept has prompted an intense search for new high capacity Na-based positive electrodes. Recently, emphasis has been placed on manipulating Na-based layered compounds to trigger the participation of the anionic network. We further explored this direction and show the feasibility of achieving anionic-redox activity in three-dimensional Na-based compounds. A new 3D β-Na1.7IrO3 phase was synthesized in a two-step process, which involves first the electrochemical removal of Li from β-Li2IrO3 to produce β-IrO3, which is subsequently reduced by electrochemical Na insertion. We show that β-Na1.7IrO3 can reversibly uptake nearly 1.3 Na+ per formula unit through an uneven voltage profile characterized by the presence of four plateaus related to structural transitions. Surprisingly, the β-Na1.7IrO3 phase was found to be stable up to 600 °C, while it could not be directly synthesized via conventional synthetic methods. Although these Na-based iridate phases are of limited practical interest, they help to understand how introducing highly polarizable guest ions (Na+) into host rocksalt-derived oxide structures affects the anionic redox mechanism. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000433403800014 |
Publication Date |
2018-05-22 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0897-4756 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
9.466 |
Times cited |
6 |
Open Access |
OpenAccess |
|
Notes |
The authors thank A. Perez for fruitful discussions and his valuable help in synchrotron XRD experiment and Matthieu Courty for carrying out the DSC measurements. The authors also greatly thank Matthieu Saubanère and Marie-Liesse Doublet for valuable discussions on theoretical aspects of this work. This work is based on experiments performed on the Materials Science and Powder Diffraction Beamline at ALBA synchrotron (Proposal 2016091814), Cerdanyola del Vallès, E- 08290 Barcelona, Spain. J.-M.T. acknowledges funding from the European Research Council (ERC) (FP/2014)/ERC Grant- Project 670116-ARPEMA. G.R. acknowledges funding from ANR DeliRedox. O.M.K., J.H., and A.M.A. are grateful to FWO Vlaanderen for financial support under Grant G040116N. |
Approved |
Most recent IF: 9.466 |
|
Call Number |
EMAT @ emat @c:irua:152048 |
Serial |
4996 |
Permanent link to this record |
|
|
|
|
Author |
Theofanidis, S.A.; Galvita, V.V.; Poelman, H.; Dharanipragada, N.V.R.A.; Longo, A.; Meledina, M.; Van Tendeloo, G.; Detavernier, C.; Marin, G.B. |
|
Title |
Fe-containing magnesium aluminate support for stability and carbon control during methane reforming |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
ACS catalysis |
Abbreviated Journal |
Acs Catal |
|
Volume |
8 |
Issue |
7 |
Pages |
5983-5995 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
We report a MgFexAl2-xO4 synthetic spinel, where x varies from 0 to 0.26, as support for Ni-based catalysts, offering stability and carbon control under various conditions of methane reforming. By incorporation of Fe into a magnesium aluminate spine!, a support is created with redox functionality and high thermal stability, as concluded from temporal analysis of products (TAP) experiments and redox cycling, respectively. A diffusion coefficient of 3 x 10(-17) m(2) s(-1) was estimated for lattice oxygen at 993 K from TAP experiments. X-ray diffraction (XRD) and extended X-ray absorption fine structure (EXAFS) modeling identified that the incorporation of iron occurs as Fe3+ in the octahedral sites of the spinel lattice, replacing aluminum. Simulation of the X-ray absorption near edge structure (XANES) spectrum of the reduced support showed that 60 +/- 10% of iron was reduced from 3+ to 2+ at 1073 K, while there was no formation of metallic iron. A series of Ni/MgFexAl2-xO4 catalysts, where x varies from 0 to 0.26, was synthesized and reduced, yielding a supported Ni-Fe alloy. The evolution of the catalyst structure during H-2 temperature-programmed reduction (TPR) and CO2 temperature-programmed oxidation (TPO) was examined using time-resolved in situ XRD and XANES. During reforming, iron in both the support and alloy keeps control of carbon accumulation, as confirmed by O-2-TPO on the spent catalysts. By fine tuning the amount of Fe in MgFexAl2-xO4, a supported alloy was obtained with a Ni/Fe molar ratio of similar to 10, which was active for reforming and stable. By comparison of the performance of Ni-based catalysts with Fe either incorporated into or deposited onto the support, the location of Fe within the support proved crucial for the stability and carbon mitigation under reforming conditions. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000438475100034 |
Publication Date |
2018-05-22 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2155-5435 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
10.614 |
Times cited |
18 |
Open Access |
OpenAccess |
|
Notes |
; This work was supported by the FAST industrialization by Catalyst Research and Development (FASTCARD) project, which is a Large Scale Collaborative Project supported by the European Commission in the 7th Framework Programme (GA no 604277), the “Long Term Structural Methusalem Funding by the Flemish Government”, the Interuniversity Attraction Poles Programme, IAP7/5, Belgian State – Belgian Science Policy, and the Fund for Scientific Research Flanders (FWO-Vlaanderen) in supplying financing of travel costs and beam time at the DUBBLE beamline of the ESRF. The authors acknowledge the assistance from the DUBBLE (ESRF, XAS campaign 26-01-1048) and ROCK staff (SOLEIL, proposal 201502561). The authors equally acknowledge support from a public grant overseen by the French National Research Agency (ANR) as part of the “Investissements d'Avenir” program (reference: ANR-10-EQPX-45) for the ROCK beamline and from Lukas Buelens and Rakesh Batchu (Laboratory for Chemical Technology, Ghent University) for the STEM measurements and TAP experiments, respectively. ; |
Approved |
Most recent IF: 10.614 |
|
Call Number |
UA @ lucian @ c:irua:153178 |
Serial |
5102 |
Permanent link to this record |
|
|
|
|
Author |
Tang, Y.; Hunter, E.C.; Battle, P.D.; Hendrickx, M.; Hadermann, J.; Cadogan, J.M. |
|
Title |
Ferrimagnetism as a consequence of unusual cation ordering in the Perovskite SrLa2FeCoSbO9 |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Inorganic chemistry |
Abbreviated Journal |
Inorg Chem |
|
Volume |
57 |
Issue |
12 |
Pages |
7438-7445 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
A polycrystalline sample of SrLa2FeCoSbO9 has been prepared in a solid-state reaction and studied by a combination of electron microscopy, magnetometry, Mossbauer spectroscopy, X-ray diffraction, and neutron diffraction. The compound adopts a monoclinic (space group P2(1)/n; a = 5.6218(6), b = 5.6221(6), c = 7.9440(8) angstrom, beta = 90.050(7)degrees at 300 K) perovskite-like crystal structure with two crystallographically distinct six-coordinate sites. One of these sites is occupied by 2/3 Co-2(+),1/3 Fe3+ and the other by 2/3 Sb5+, 1/3 Fe3+. This pattern of cation ordering results in a transition to a ferrimagnetic phase at 215 K. The magnetic moments on nearest-neighbor, six-coordinate cations align in an antiparallel manner, and the presence of diamagnetic Sb5+ on only one of the two sites results in a nonzero remanent magnetization of similar to 1 mu(B) per formula unit at 5 K. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Easton, Pa |
Editor |
|
|
Language |
|
Wos |
000436023800073 |
Publication Date |
2018-05-29 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0020-1669 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
4.857 |
Times cited |
6 |
Open Access |
Not_Open_Access |
|
Notes |
; PDB, ECH, and JH acknowledge support from EPSRC under grant EP/M0189954/1. We would like to thank the STFC for the award of beamtime at the ISIS Neutron and Muon Source (RB 1610100), and we thank Dr. I. da Silva for the assistance provided. We also thank Dr. R Paria Sena for help with the HAADF-STEM and STEM-EDX experiments. ; |
Approved |
Most recent IF: 4.857 |
|
Call Number |
UA @ lucian @ c:irua:152485 |
Serial |
5103 |
Permanent link to this record |
|
|
|
|
Author |
Tong, Y.; Yao, E.-P.; Manzi, A.; Bladt, E.; Wang, K.; Doeblinger, M.; Bals, S.; Mueller-Buschbaum, P.; Urban, A.S.; Polavarapu, L.; Feldmann, J. |
|
Title |
Spontaneous self-assembly of Perovskite nanocrystals into electronically coupled supercrystals : toward filling the green gap |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Advanced materials |
Abbreviated Journal |
Adv Mater |
|
Volume |
30 |
Issue |
30 |
Pages |
1801117 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
Self-assembly of nanoscale building blocks into ordered nanoarchitectures has emerged as a simple and powerful approach for tailoring the nanoscale properties and the opportunities of using these properties for the development of novel optoelectronic nanodevices. Here, the one-pot synthesis of CsPbBr3 perovskite supercrystals (SCs) in a colloidal dispersion by ultrasonication is reported. The growth of the SCs occurs through the spontaneous self-assembly of individual nanocrystals (NCs), which form in highly concentrated solutions of precursor powders. The SCs retain the high photoluminescence (PL) efficiency of their NC subunits, however also exhibit a redshifted emission wavelength compared to that of the individual nanocubes due to interparticle electronic coupling. This redshift makes the SCs pure green emitters with PL maxima at approximate to 530-535 nm, while the individual nanocubes emit a cyan-green color (approximate to 512 nm). The SCs can be used as an emissive layer in the fabrication of pure green light-emitting devices on rigid or flexible substrates. Moreover, the PL emission color is tunable across the visible range by employing a well-established halide ion exchange reaction on the obtained CsPbBr3 SCs. These results highlight the promise of perovskite SCs for light emitting applications, while providing insight into their collective optical properties. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Weinheim |
Editor |
|
|
Language |
|
Wos |
000438709400019 |
Publication Date |
2018-06-05 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0935-9648 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
19.791 |
Times cited |
161 |
Open Access |
OpenAccess |
|
Notes |
; This research work was supported by the Bavarian State Ministry of Science, Research, and Arts through the grant “Solar Technologies go Hybrid (SolTech),” by the China Scholarship Council (Y.T. and K.W.), by the European Union's Horizon 2020 research and innovation program under the Marie Skodowska-Curie Grant Agreement COMPASS No. 691185 and by LMU Munich's Institutional Strategy LMUexcellent within the framework of the German Excellence Initiative (L.P., J.F. and A.S.U.). E.B. and S.B. acknowledge financial support from the European Research Council (ERC Starting Grant #335078-COLOURATOMS). The authors would like to thank Alexander Richter for helpful discussions. ; ecas_Sara |
Approved |
Most recent IF: 19.791 |
|
Call Number |
UA @ lucian @ c:irua:152413UA @ admin @ c:irua:152413 |
Serial |
5129 |
Permanent link to this record |
|
|
|
|
Author |
Amini, M.N.; Altantzis, T.; Lobato, I.; Grzelczak, M.; Sánchez-Iglesias, A.; Van Aert, S.; Liz-Marzán, L.M.; Partoens, B.; Bals, S.; Neyts, E.C. |
|
Title |
Understanding the Effect of Iodide Ions on the Morphology of Gold Nanorods |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Particle and particle systems characterization |
Abbreviated Journal |
Part Part Syst Char |
|
Volume |
35 |
Issue |
35 |
Pages |
1800051 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Condensed Matter Theory (CMT); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
|
Abstract |
The presence of iodide ions during the growth of gold nanorods strongly affects the shape of the final products, which is proposed to be due to selective iodide adsorption on certain crystallographic facets. Therefore, a detailed structural and morphological characterization of the starting rods is crucial toward understanding this effect. Electron tomography is used to determine the crystallographic indices of the lateral facets of gold nanorods, as well as those present at the tips. Based on this information, density functional theory calculations are used to determine the surface and interface energies of the observed facets and provide insight into the relationship between the amount of iodide ions in the growth solution and the final morphology of anisotropic gold nanoparticles. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000441893400002 |
Publication Date |
2018-06-10 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0934-0866 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
4.474 |
Times cited |
6 |
Open Access |
OpenAccess |
|
Notes |
This work was supported by the European Research Council (grant 335078 COLOURATOM to S.B.). T.A., S.V.A. S.B. and E.C.N., acknowledge funding from the Research Foundation Flanders (FWO, Belgium), through project funding (G.0218.14N and G.0369.15N) and a postdoctoral grant to T.A. L.M.L.-M. and M.G. acknowledge funding from the Spanish Ministerio de Economía y Competitividad (grant MAT2013-46101-R). Mozhgan N. Amini and Thomas Altantzis contributed equally to this work. (ROMEO:yellow; preprint:; postprint:restricted ; pdfversion:cannot); ecas_sara |
Approved |
Most recent IF: 4.474 |
|
Call Number |
EMAT @ emat @c:irua:152998UA @ admin @ c:irua:152998 |
Serial |
5010 |
Permanent link to this record |
|
|
|
|
Author |
van der Burgt, J.S.; Geuchies, J.J.; van der Meer, B.; Vanrompay, H.; Zanaga, D.; Zhang, Y.; Albrecht, W.; Petukhov, A.V.; Filion, L.; Bals, S.; Swart, I.; Vanmaekelbergh, D. |
|
Title |
Cuboidal supraparticles self-assembled from cubic CsPbBr3 perovskite nanocrystals |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
The journal of physical chemistry: C : nanomaterials and interfaces |
Abbreviated Journal |
J Phys Chem C |
|
Volume |
122 |
Issue |
122 |
Pages |
15706-15712 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
Colloidal CsPbBr3 nanocrystals (NCs) have emerged as promising candidates for various opto-electronic applications, such as light-emitting diodes, photodetectors, and solar cells. Here, we report on the self-assembly of cubic NCs from an organic suspension into ordered cuboidal supraparticles (SPs) and their structural and optical properties. Upon increasing the NC concentration or by addition of a nonsolvent, the formation of the SPs occurs homogeneously in the suspension, as monitored by in situ X-ray scattering measurements. The three-dimensional structure of the SPs was resolved through high-angle annular dark-field scanning transmission electron microscopy and electron tomography. The NCs are atomically aligned but not connected. We characterize NC vacancies on superlattice positions both in the bulk and on the surface of the SPs. The occurrence of localized atomic-type NC vacancies-instead of delocalized ones-indicates that NC-NC attractions are important in the assembly, as we verify with Monte Carlo simulations. Even when assembled in SPs, the NCs show bright emission, with a red shift of about 30 meV compared to NCs in suspension. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Washington, D.C. |
Editor |
|
|
Language |
|
Wos |
000439003600071 |
Publication Date |
2018-06-14 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
1932-7447; 1932-7455 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
4.536 |
Times cited |
60 |
Open Access |
OpenAccess |
|
Notes |
; The authors thank Dr. Rajeev Dattani and Jacques Gorini from the ID02 beamline of the ESRF for their excellent assistance during the X-ray scattering experiments. We also thank Carlo van Overbeek, P. Tim Prins, and Federico Montanarella for their support during the synchrotron experiments. The authors gratefully acknowledge Prof. Dr. Alfons van Blaaderen for fruitful discussions. D.V. acknowledges funding from NWO-CW TOPPUNT “Superficial superstructures.” J.J.G. acknowledges the joint Debye and ESRF graduate programs for the financial support. H.V. gratefully acknowledges the financial support by the Flemish Fund for Scientific Research (FWO grant 1S32617NN). S.B. acknowledges the financial support from the European Research Council (ERC Starting grant # 335078-COLOURATOMS). Y.Z. acknowledges the financial support from the European Union's Horizon 2020 research and innovation program, under the Marie Sklodowska-Curie grant agreement #665501 through a FWO [PEGASUS]2 Marie Sklodowska-Curie fellowship (12U4917N). W.A. acknowledges the financial support from the European Research Council under the European Unions Seventh Framework Program (FP-2007-2013)/ERC Advanced grant agreement 291667 HierarSACol. ; ecas_Sara |
Approved |
Most recent IF: 4.536 |
|
Call Number |
UA @ lucian @ c:irua:153161UA @ admin @ c:irua:153161 |
Serial |
5087 |
Permanent link to this record |
|
|
|
|
Author |
Bhat, S.G.; Gauquelin, N.; Sebastian, N.K.; Sil, A.; Béché, A.; Verbeeck, J.; Samal, D.; Kumar, P.S.A. |
|
Title |
Orthorhombic vs. hexagonal epitaxial SrIrO3 thin films : structural stability and related electrical transport properties |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Europhysics letters |
Abbreviated Journal |
Epl-Europhys Lett |
|
Volume |
122 |
Issue |
2 |
Pages |
28003 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Metastable orthorhombic SrIrO3 (SIO) is an arch-type spin-orbit coupled material. We demonstrate here a controlled growth of relatively thick (200 nm) SIO films that transform from bulk “6H-type” structure with monoclinic distortion to an orthorhombic lattice by controlling growth temperature. Extensive studies based on high-resolution X-ray diffraction and transmission electron microscopy infer a two distinct structural phases of SIO. Electrical transport reveals a weak temperature-dependent semi-metallic character for both phases. However, the temperature-dependent Hall-coefficient for the orthorhombic SIO exhibits a prominent sign change, suggesting a multiband character in the vicinity of E-F. Our findings thus unravel the subtle structure-property relation in SIO epitaxial thin films. Copyright (C) EPLA, 2018 |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Paris |
Editor |
|
|
Language |
|
Wos |
000435517300001 |
Publication Date |
2018-06-18 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0295-5075 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
1.957 |
Times cited |
4 |
Open Access |
Not_Open_Access |
|
Notes |
; SGB and DS acknowledge useful discussions with E. P. Houwman, University of Twente, on X-ray diffraction. DS would like to thank H. Takagi, Max-Planck Institute for Solid State Research, Stuttgart, for the fruitful discussion on the transport properties of SIO thin films. SGB and NKS thank A. Aravind, Bishop Moore College, Mavelikara, for his valuable inputs while depositing the thin films of SIO. SGB, NKS and PSAK acknowledge Nano Mission Council, Department of Science & Technology, India, for the funding. DS acknowledges the financial support from Max-Planck Society through MaxPlanck Partner Group. NG, AB and JV acknowledge funding from GOA project “Solarpaint” of the University of Antwerp and FWO project G093417N. ; |
Approved |
Most recent IF: 1.957 |
|
Call Number |
UA @ lucian @ c:irua:152074UA @ admin @ c:irua:152074 |
Serial |
5034 |
Permanent link to this record |
|
|
|
|
Author |
Morozov, V.; Deyneko, D.; Basoyich, O.; Khaikina, E.G.; Spassky, D.; Morozov, A.; Chernyshev, V.; Abakumov, A.; Hadermann, J. |
|
Title |
Incommensurately modulated structures and luminescence properties of the AgxSm(2-x)/3WO4 (x=0.286, 0.2) scheelites as thermographic phosphors |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Chemistry of materials |
Abbreviated Journal |
Chem Mater |
|
Volume |
30 |
Issue |
14 |
Pages |
4788-4798 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Ag+ for Sm3+ substitution in the scheelite-type AgxSm(2-x)/3 square(1-2x)/3WO4 tungstates has been investigated for its influence on the cation-vacancy ordering and luminescence properties. A solid state method was used to synthesize the x = 0.286 and x = 0.2 compounds, which exhibited (3 + 1)D incommensurately modulated structures in the transmission electron microscopy study. Their structures were refined using high resolution synchrotron powder X-ray diffraction data. Under near-ultraviolet light, both compounds show the characteristic emission lines for (4)G(5/2) -> H-6(J) (J = 5/2, 7/2, 9/2, and 11/2) transitions of the Sm3+ ions in the range 550-720 nm, with the J = 9/2 transition at the similar to 648 nm region being dominant for all photoluminescence spectra. The intensities of the (4)G(5/2) -> H-6(9/2) and (4)G(5/2) -> H-6(7/2) bands have different temperature dependencies. The emission intensity ratios (R) for these bands vary reproducibly with temperature, allowing the use of these materials as thermographic phosphors. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
American Chemical Society |
Place of Publication |
Washington, D.C |
Editor |
|
|
Language |
|
Wos |
000440105500037 |
Publication Date |
2018-06-21 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0897-4756 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
9.466 |
Times cited |
2 |
Open Access |
Not_Open_Access |
|
Notes |
; This research was supported by FWO (Project G039211N), Flanders Research Foundation. The research was carried out within the state assignment of FASO of Russia (Themes No. 0339-2016-0007). V.M. thanks the Russian Foundation for Basic Research (Grant 18-03-00611) for financial support. E.G.K. and O.B. acknowledge financial support from the Russian Foundation for Basic Research (Grant 16-03-00510). D.D. thanks the Foundation of the Russian Federation President (Grant MK-3502.2018.5) for financial support. We are grateful to the ESRF for granting the beamtime. V.C. is grateful for the financial support of the Russian Ministry of Science and Education (Project No. RFMEFI61616X0069). We are grateful to the ESRF for the access to ID22 station (experiment MA-3313). ; |
Approved |
Most recent IF: 9.466 |
|
Call Number |
UA @ lucian @ c:irua:153156 |
Serial |
5107 |
Permanent link to this record |
|
|
|
|
Author |
Van Goethem, C.; Verbeke, R.; Pfanmoeller, M.; Koschine, T.; Dickmann, M.; Timpel-Lindner, T.; Egger, W.; Bals, S.; Vankelecom, I.F.J. |
|
Title |
The role of MOFs in Thin-Film Nanocomposite (TFN) membranes |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Journal of membrane science |
Abbreviated Journal |
J Membrane Sci |
|
Volume |
563 |
Issue |
563 |
Pages |
938-948 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Incorporation of MOFs in interfacially polymerized Thin-Film Nanocomposite (TFN) membranes has widely been shown to result in increased membrane performance. However, the exact functioning of these membranes is poorly understood as large variability in permeance increase, filler incorporation and rejection changes can be observed in literature. The synthesis and functioning of TFN membranes (herein exemplified by ZIF-8 filled polyamide (PA) membranes prepared via the EFP method) was investigated via targeted membrane synthesis and thorough characterization via STEM-EDX, XRD and PALS. It is hypothesized that the acid generated during the interfacial polymerization (IP) at least partially degrades the crystalline, acid-sensitive ZIF-8 and that this influences the membrane formation (through so-called secondary effects, i.e. not strictly linked to the pore morphology of the MOF). Nanoscale HAADF-STEM imaging and STEM-EDX Zn-mapping revealed no ZIF-8 particles but rather the presence of randomly shaped regions with elevated Zn-content. Also XRD failed to show the presence of crystalline areas in the composite PA films. As the addition of the acid-quenching TEA led to an increase in the diffraction signal observed in XRD, the role of the acid was confirmed. The separate addition of dissolved Zn2+ to the synthesis of regular TFC membranes showed an increase in permeance while losing some salt retention, similar to observations regularly made for TFN membranes. While the addition of a porous material to a TFC membrane is a straightforward concept, all obtained results indicate that the synthesis and performance of such composite membranes is often more complex than commonly accepted. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
|
Language |
|
Wos |
000441897200099 |
Publication Date |
2018-06-22 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0376-7388 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
6.035 |
Times cited |
84 |
Open Access |
OpenAccess |
|
Notes |
; C.V.G. and R.V. kindly acknowledge respectively the Flemish Agency for Innovation through Science and Technology (IWT) (IWT, 141697) and the Flemish Fund for Scientific Research (FWO, 1500917N) for a PhD scholarship. The authors kindly acknowledge funding from KU Leuven through C16/17/005 and from the Belgian Federal Government through IAP 6/27 Functional Supramolecular systems. S.B. and M.P. acknowledge financial support from the European Research Council (ERC Starting Grant #335078-COLOURATOM). M.P. acknowledges funding from the European Union (ESTEEM2, No. 312483) and the HEiKA centre FunTECH-3D (Ministry of Science, Research and Art Baden-Wurttemberg, AZ: 33-753-30-20/3/3). The MLZ-Garching is kindly acknowledged for providing access to the NEPOMUC facilities (project no 11541). ; ecas_sara |
Approved |
Most recent IF: 6.035 |
|
Call Number |
UA @ lucian @ c:irua:153618UA @ admin @ c:irua:153618 |
Serial |
5132 |
Permanent link to this record |
|
|
|
|
Author |
Cremers, V.; Rampelberg, G.; Barhoum, A.; Walters, P.; Claes, N.; Oliveira, T.M. de; Assche, G.V.; Bals, S.; Dendooven, J.; Detavernier, C. |
|
Title |
Oxidation barrier of Cu and Fe powder by Atomic Layer Deposition |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Surface and coatings technology |
Abbreviated Journal |
Surf Coat Tech |
|
Volume |
349 |
Issue |
349 |
Pages |
1032-1041 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Atomic layer deposition (ALD) is a vapor based technique which allows to deposit uniform, conformal films with a thickness control at the atomic scale. In this research, Al 2 O 3 coatings were deposited on micrometer-sized Fe and Cu powder (particles) using the thermal trimethylaluminum (TMA)/ water (H 2 O) process in a rotary pump-type ALD reactor. Rotation of the powder during deposition was required to obtain a pinhole-free ALD coating. The protective nature of the coating was evaluated by quantifying its effectiveness in protecting the metal particles during oxidative annealing treatments. The Al 2 O 3 coated powders were annealed in ambient air while in-situ thermogravimetric analysis (TGA) and in-situ x-ray diffraction (XRD) data were acquired. The thermal stability of a series of Cu and Fe powder with different Al 2 O 3 thicknesses were determined with TGA. In both samples a clear shift in oxidation temperature is visible. For Cu and Fe powder coated with 25 nm Al 2 O 3 , we observed an increase of the oxidation temperature with 300-400°C. For the Cu powder a thin film of only 8 nm is required to obtain an initial increase in oxidation temperature of 200°C. In contrast, for Fe powder a thicker coating of 25 nm is required. In both cases, the oxidation temperature increases with increasing thickness of the Al 2 O 3 coating. These results illustrate that the Al 2 O 3 thin film, deposited by the thermal ALD process (TMA/H 2 O) can be an efficient and pinhole-free barrier layer for micrometer-sized powder particles, provided that the powder is properly agitated during the process to ensure sufficient vapour-solid interaction. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000441492600108 |
Publication Date |
2018-06-25 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0257-8972 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
2.589 |
Times cited |
10 |
Open Access |
OpenAccess |
|
Notes |
The authors acknowledge financial support from the Strategic Initiative Materials in Flanders (SIM, SBO-FUNC project) and the Special Research Fund BOF of Ghent University (GOA 01G01513). J. D. acknowledges the Research Foundation Flanders (FWO-Vlaanderen) for a postdoctoral fellowship. N.C. and S.B. acknowledge financial support from European Research Council (ERC Starting Grant 335078-COLOURATOMS). The authors acknowledge S. Goeteyn for the assistance in preliminary depositions. (ROMEO:green; preprint:; postprint:can ; pdfversion:cannot); ecas_sara |
Approved |
Most recent IF: 2.589 |
|
Call Number |
EMAT @ emat @c:irua:152174UA @ admin @ c:irua:152174 |
Serial |
4994 |
Permanent link to this record |
|
|
|
|
Author |
Wu, S.-M.; Liu, X.-L.; Lian, X.-L.; Tian, G.; Janiak, C.; Zhang, Y.-X.; Lu, Y.; Yu, H.-Z.; Hu, J.; Wei, H.; Zhao, H.; Chang, G.-G.; Van Tendeloo, G.; Wang, L.-Y.; Yang, X.-Y.; Su, B.-L. |
|
Title |
Homojunction of oxygen and titanium vacancies and its interfacial n-p effect |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Advanced materials |
Abbreviated Journal |
Adv Mater |
|
Volume |
30 |
Issue |
32 |
Pages |
1802173 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
The homojunction of oxygen/metal vacancies and its interfacial n-p effect on the physiochemical properties are rarely reported. Interfacial n-p homojunctions of TiO2 are fabricated by directly decorating interfacial p-type titanium-defected TiO2 around n-type oxygen-defected TiO2 nanocrystals in amorphous-anatase homogeneous nanostructures. Experimental measurements and theoretical calculations on the cell lattice parameters show that the homojunction of oxygen and titanium vacancies changes the charge density of TiO2; a strong EPR signal caused by oxygen vacancies and an unreported strong titanium vacancies signal of 2D H-1 TQ-SQ MAS NMR are present. Amorphous-anatase TiO2 shows significant performance regarding the photogeneration current, photocatalysis, and energy storage, owing to interfacial n-type to p-type conductivity with high charge mobility and less structural confinement of amorphous clusters. A new homojunction of oxygen and titanium vacancies concept, characteristics, and mechanism are proposed at an atomic-/nanoscale to clarify the generation of oxygen vacancies and titanium vacancies as well as the interface electron transfer. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Weinheim |
Editor |
|
|
Language |
|
Wos |
000440813300022 |
Publication Date |
2018-06-27 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0935-9648 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
19.791 |
Times cited |
39 |
Open Access |
Not_Open_Access |
|
Notes |
; This work was supported by National Key R&D Program of China (2017YFC1103800), National SFC (U1662134, U1663225, 51472190, 51611530672, 21711530705, 51503166, 21706199), ISTCP (2015DFE52870), PCSIRT (IRT_15R52), HPNSF (2016CFA033, 2017CFB487), and SKLPPC (PPC2016007). ; |
Approved |
Most recent IF: 19.791 |
|
Call Number |
UA @ lucian @ c:irua:153106 |
Serial |
5105 |
Permanent link to this record |
|
|
|
|
Author |
Sandoval, S.; Kepic, D.; Perez del Pino, A.; Gyorgy, E.; Gomez, A.; Pfannmöller, M.; Van Tendeloo, G.; Ballesteros, B.; Tobias, G. |
|
Title |
Selective laser-assisted synthesis of tubular van der Waals heterostructures of single-layered PbI2 within carbon nanotubes exhibiting carrier photogeneration |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
ACS nano |
Abbreviated Journal |
Acs Nano |
|
Volume |
12 |
Issue |
7 |
Pages |
6648-6656 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
The electronic and optical properties of two-dimensional layered materials allow the miniaturization of nanoelectronic and optoelectronic devices in a competitive manner. Even larger opportunities arise when two or more layers of different materials are combined. Here, we report on an ultrafast energy efficient strategy, using laser irradiation, which allows bulk synthesis of crystalline single-layered lead iodide in the cavities of carbon nanotubes by forming cylindrical van der Waals heterostructures. In contrast to the filling of van der Waals solids into carbon nanotubes by conventional thermal annealing, which favors the formation of inorganic nanowires, the present strategy is highly selective toward the growth of monolayers forming lead iodide nanotubes. The irradiated bulk material bearing the nanotubes reveals a decrease of the resistivity as well as a significant increase in the current flow upon illumination. Both effects are attributed to the presence of single-walled lead iodide nanotubes in the cavities of carbon nanotubes, which dominate the properties of the whole matrix. The present study brings in a simple, ultrafast and energy efficient strategy for the tailored synthesis of rolled-up single-layers of lead iodide (i.e., single-walled PbI2 nanotubes), which we believe could be expanded to other two-dimensional (2D) van der Waals solids. In fact, initial tests with ZnI2 already reveal the formation of single-walled ZnI2 nanotubes, thus proving the versatility of the approach. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000440505000029 |
Publication Date |
2018-07-05 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
1936-0851 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
13.942 |
Times cited |
8 |
Open Access |
OpenAccess |
|
Notes |
; We acknowledge funding from MINECO (Spain), through MAT2017-86616-R, ENE2017-89210-C2-1-R, and “Severo Ochoa” Programme for Centres of Excellence in R&D (SEV-2015-0496, SEV-2013-0295), CERCA programme for funding ICN2 and support from AGAUR of Generalitat de Catalunya through the projects 2017 SGR 1086, 2017 SGR 581 and 2017 SGR 327. We thank Thomas Swan Co., Ltd., for supplying MWCNT Elicarb samples. D.K. acknowledges financial support from the Ministry of Education, Science, and Technological Development of the Republic of Serbia for postdoctoral research. We are grateful to R Rurali (ICMAB-CSIC) for providing the structural model of the PbI<INF>2</INF> nanotube employed for the schematic representation of PbI<INF>2</INF>@MVWCNT. ; |
Approved |
Most recent IF: 13.942 |
|
Call Number |
UA @ lucian @ c:irua:153169 |
Serial |
5127 |
Permanent link to this record |
|
|
|
|
Author |
Weng, Y.; Jia, Z.; Ding, L.; Muraishi, S.; Liu, Q. |
|
Title |
Clustering behavior during natural aging and artificial aging in Al-Mg-Si alloys with different Ag and Cu addition |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Microstructure And Processing |
Abbreviated Journal |
Mat Sci Eng A-Struct |
|
Volume |
732 |
Issue |
732 |
Pages |
273-283 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
The effect of Ag and Cu addition on clustering behavior of Al-Mg-Si alloys during natural aging (NA) and artificial aging (AA) was investigated by hardness measurement, tensile test and atom probe tomography analysis. The results show that both Ag and Cu atoms could enter clusters and GP-zones, change the Mg/Si ratio and increase their volume fractions. Compared with the Al base alloy, the clusters in the Ag/Cu-added alloys more easily transform to beta" phases for size and compositional similarity, and the strengthening ability of these particles is enhanced by the increased volume fraction and shear modulus. In NA condition, Cu is greater in improving the volume fraction of clusters than Ag and thus produces higher T4 temper hardness. In AA condition, in contrary, Ag is more effective in facilitating the formation and growth of particles than Cu due to the stronger Ag-Mg interaction and the high diffusivity of Ag atoms in Al matrix, leading to highest hardening response. Compared to the Cu-added alloy, the Ag-added alloy shows higher precipitation kinetics during AA treatment and maintains a lower T4 temper hardness. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
|
Language |
|
Wos |
000441486100032 |
Publication Date |
2018-07-07 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0921-5093 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
3.094 |
Times cited |
11 |
Open Access |
OpenAccess |
|
Notes |
; This work was supported by the Special major R & D Projects for Key Technology Innovation of Key Industries in Chongqing (Grant no. cstc2017zdcy-zdzxX0006), the Fundamental Research Funds for the Central Universities of China (Grant no. 106112016CDJXZ338825 and 106112017CDJQJ308822) and the program of China Scholarships Council (No. 201706050125). ; |
Approved |
Most recent IF: 3.094 |
|
Call Number |
UA @ lucian @ c:irua:153107 |
Serial |
5083 |
Permanent link to this record |
|
|
|
|
Author |
Weng, Y.; Jia, Z.; Ding, L.; Muraishi, S.; Wu, X.; Liu, Q. |
|
Title |
The multiple orientation relationships and morphology of beta phase in Al-Mg-Si-Cu alloy |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Journal of alloys and compounds |
Abbreviated Journal |
J Alloy Compd |
|
Volume |
767 |
Issue |
767 |
Pages |
81-89 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
The orientation relationships (ORs), segregation behavior and morphologies of beta precipitate in an over aged Al-Mg-Si-Cu alloy are systematically characterized by atomic resolution high-angle annular dark field scanning transmission electron microscopy (HAADF-STEM). Six different ORs and two morphologies, i.e. rod-and lath-like are revealed for beta precipitates, and Cu segregation at the (beta/alpha-Al interface is observed in all these precipitates. The rod-like beta precipitate has multiple beta-angles ranging from 6.1 to 14.1 degrees and non-uniform Cu segregation at the (beta/alpha-Al interface, while the lath-like beta precipitate has a constant beta-angle of 0 degrees and a periodic Cu segregation. These different ORs are explained to be attributable to the rotation of QP lattice, a near-hexagonal network of Si columns formed within beta precipitates, which causes different lattice matching of beta with alpha-Al lattice. These findings provide new insights in controlling the precipitation hardening and mechanical properties of this type of alloys. (C) 2018 Elsevier B.V. All rights reserved. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
|
Language |
|
Wos |
000446316500011 |
Publication Date |
2018-07-09 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0925-8388 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
3.133 |
Times cited |
4 |
Open Access |
OpenAccess |
|
Notes |
; This work was supported by the Fundamental Research Funds for the Central Universities of China (Grant No. 2018CDJDCL001910611 and No. 2017CDJQJ308822), the Foundation for Innovative Research Groups of the National Natural Science Foundation of China (Grant No. 51421001) and the program of China Sponsorship Council (No. 201706050125). ; |
Approved |
Most recent IF: 3.133 |
|
Call Number |
UA @ lucian @ c:irua:154720 |
Serial |
5131 |
Permanent link to this record |
|
|
|
|
Author |
Zhou, Y.; Che, F.; Liu, M.; Zou, C.; Liang, Z.; De Luna, P.; Yuan, H.; Li, J.; Wang, Z.; Xie, H.; Li, H.; Chen, P.; Bladt, E.; Quintero-Bermudez, R.; Sham, T.-K.; Bals, S.; Hofkens, J.; Sinton, D.; Chen, G.; Sargent, E.H. |
|
Title |
Dopant-induced electron localization drives CO2 reduction to C2 hydrocarbons |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Nature chemistry |
Abbreviated Journal |
Nat Chem |
|
Volume |
10 |
Issue |
10 |
Pages |
974-980 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
The electrochemical reduction of CO2 to multi-carbon products has attracted much attention because it provides an avenue to the synthesis of value-added carbon-based fuels and feedstocks using renewable electricity. Unfortunately, the efficiency of CO2 conversion to C-2 products remains below that necessary for its implementation at scale. Modifying the local electronic structure of copper with positive valence sites has been predicted to boost conversion to C-2 products. Here, we use boron to tune the ratio of Cu delta+ to Cu-0 active sites and improve both stability and C-2-product generation. Simulations show that the ability to tune the average oxidation state of copper enables control over CO adsorption and dimerization, and makes it possible to implement a preference for the electrosynthesis of C-2 products. We report experimentally a C-2 Faradaic efficiency of 79 +/- 2% on boron-doped copper catalysts and further show that boron doping leads to catalysts that are stable for in excess of similar to 40 hours while electrochemically reducing CO2 to multi-carbon hydrocarbons. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000442395200013 |
Publication Date |
2018-07-13 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
1755-4330; 1755-4349 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
25.87 |
Times cited |
700 |
Open Access |
OpenAccess |
|
Notes |
; This work was supported financially by funding from TOTAL S.A., the Ontario Research Fund: Research Excellence Program, the Natural Sciences and Engineering Research Council of Canada, the CIFAR Bio-Inspired Solar Energy programme, a University of Toronto Connaught grant, the Ministry of Science, Natural Science Foundation of China (21471040, 21271055 and 21501035), the Innovation-Driven Plan in Central South University project (2017CX003), a project from State Key Laboratory of Powder Metallurgy in Central South University, the Thousand Youth Talents Plan of China and Hundred Youth Talents Program of Hunan and the China Scholarship Council programme. This work benefited from the soft X-ray microcharacterization beamline at CLS, sector 20BM at the APS and the Ontario Centre for the Characterisation of Advanced Materials at the University of Toronto. H.Y. acknowledges financial support from the Research Foundation-Flanders (FWO postdoctoral fellowship). C.Z. acknowledges support from the International Academic Exchange Fund for Joint PhD Students from Tianjin University. P.D.L. acknowledges financial support from the Natural Sciences and Engineering Research Council in the form of the Canada Graduate Scholarship-Doctoral award. S.B. and E.B. acknowledge financial support from the European Research Council (ERC Starting Grant # 335078-COLOURATOMS). The authors thank B. Zhang, N. Wang, C. T. Dinh, T. Zhuang, J. Li and Y. Zhao for fruitful discussions, as well as Y. Hu and Q. Xiao from CLS, and Z. Finfrock and M. Ward from APS for their help during the course of study. Computations were performed on the SOSCIP Consortium's Blue Gene/Q computing platform. SOSCIP is funded by the Federal Economic Development Agency of Southern Ontario, the Province of Ontario, IBM Canada, Ontario Centres of Excellence, Mitacs and 15 Ontario academic member institutions. ; ecas_sara |
Approved |
Most recent IF: 25.87 |
|
Call Number |
UA @ lucian @ c:irua:153693UA @ admin @ c:irua:153693 |
Serial |
5091 |
Permanent link to this record |