|   | 
Details
   web
Records
Author Afanasov, I.M.; Morozov, V.A.; Kepman, A.V.; Ionov, S.G.; Seleznev, A.N.; Van Tendeloo, G.; Audeev, V.V.
Title Preparation, electrical and thermal properties of new exfoliated graphite-based composites Type A1 Journal article
Year 2009 Publication Carbon Abbreviated Journal Carbon
Volume 47 Issue (up) 1 Pages 263-270
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Exfoliated graphite samples (EG) with different bulk densities were prepared by the exfoliation of expandable graphite under a thermal shock regime. As a conductive filler, EG has been incorporated successfully into the coal tar pitch matrix by mechanical mixing. The conducting behavior of the composite was interpreted based on the percolation theory. The percolation threshold of the EG/pitch conducting composites at room temperature was as low as 1.5 wt% and did not depend on the bulk density of the EG used. By means of thermogravimetry the improvement of thermal stability of the composites in comparison with pure pitches was detected. The phenomenon was ascribed to heat shielding effect of the EG particles evidenced by matrix-assisted laser desorption/ionization mass spectrometry.
Address
Corporate Author Thesis
Publisher Place of Publication Oxford Editor
Language Wos 000262143500032 Publication Date 2008-10-14
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0008-6223; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 6.337 Times cited 42 Open Access
Notes Iap-Vi Approved Most recent IF: 6.337; 2009 IF: 4.504
Call Number UA @ lucian @ c:irua:75767 Serial 2701
Permanent link to this record
 

 
Author Piedigrosso, P.; Konya, Z.; Colomer, J.-F.; Fonseca, A.; Van Tendeloo, G.; Nagy, J.B.
Title Production of differently shaped multi-wall carbon nanotubes using various cobalt supported catalysts Type A1 Journal article
Year 2000 Publication Physical chemistry, chemical physics Abbreviated Journal Phys Chem Chem Phys
Volume 2 Issue (up) 1 Pages 163-170
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Catalytic synthesis and transmission electron microscopy (TEM) of multi-wall carbon nanotubes are presented. Silica, zeolite and alumina supported cobalt catalysts were prepared by different methods (impregnation and ion-adsorption precipitation) and were used to produce nanotubes. The synthesis was carried out in a fixed bed flow reactor and the process was optimized in order to produce carbon nanotubes on a gram scale. The influence of various parameters such as the method of catalyst preparation, the nature of the support, cobalt concentration and reaction conditions on the formation of nanotubes was investigated. The carbon deposits were measured and the quality of nanotubes was determined by low and high resolution TEM. Multi-wall straight and coiled nanotubes were found to be fairly regular with an average inner (outer) diameter of 4-7 nm (8-23 nm) and with lengths up to 0.1 mm.
Address
Corporate Author Thesis
Publisher Place of Publication Cambridge Editor
Language Wos 000084333800025 Publication Date 2002-07-26
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1463-9076;1463-9084; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 4.123 Times cited 53 Open Access
Notes Approved Most recent IF: 4.123; 2000 IF: 1.653
Call Number UA @ lucian @ c:irua:102889 Serial 2723
Permanent link to this record
 

 
Author Rodríguez-Fernández, D.; Altantzis, T.; Heidari, H.; Bals, S.; Liz-Marzan, L.M.
Title A protecting group approach toward synthesis of Au-silica Janus nanostars Type A1 Journal article
Year 2014 Publication Chemical communications Abbreviated Journal Chem Commun
Volume 50 Issue (up) 1 Pages 79-81
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract The concept of protecting groups, widely used in organic chemistry, has been applied for the synthesis of Au-silica Janus stars, in which gold branches protrude from one half of Au-silica Janus spheres. This configuration opens up new possibilities to apply the plasmonic properties of gold nanostars, as well as a variety of chemical functionalizations on the silica component.
Address
Corporate Author Thesis
Publisher Place of Publication London Editor
Language Wos 000327606000017 Publication Date 2013-10-22
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1359-7345;1364-548X; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 6.319 Times cited 26 Open Access OpenAccess
Notes 262348 Esmi; 335078 Colouratom; 267867 Plasmaquo; ECAS_Sara; (ROMEO:yellow; preprint:; postprint:restricted ; pdfversion:cannot); Approved Most recent IF: 6.319; 2014 IF: 6.834
Call Number UA @ lucian @ c:irua:112774 Serial 2732
Permanent link to this record
 

 
Author Altantzis, T.; Goris, B.; Sánchez-Iglesias, A.; Grzelczak, M.; Liz-Marzán, L.M.; Bals, S.
Title Quantitative structure determination of large three-dimensional nanoparticle assemblies Type A1 Journal article
Year 2013 Publication Particle and particle systems characterization Abbreviated Journal Part Part Syst Char
Volume 30 Issue (up) 1 Pages 84-88
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Thumbnail image of graphical abstract To investigate nanoassemblies in three dimensions, electron tomography is an important tool. For large nanoassemblies, it is not straightforward to obtain quantitative results in three dimensions. An optimized acquisition technique, incoherent bright field scanning transmission electron microscopy, is combined with an advanced 3D reconstruction algorithm. The approach is applied to quantitatively analyze large nanoassemblies in three dimensions.
Address
Corporate Author Thesis
Publisher Place of Publication Weinheim Editor
Language Wos 000310806000008 Publication Date 2012-11-07
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0934-0866; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 4.474 Times cited 23 Open Access
Notes Goa; Fwo; 267867 Plasmaquo; 262348 Esmi Approved Most recent IF: 4.474; 2013 IF: 0.537
Call Number UA @ lucian @ c:irua:101776 Serial 2763
Permanent link to this record
 

 
Author Sels, D.; Sorée, B.; Groeseneken, G.
Title Quantum ballistic transport in the junctionless nanowire pinch-off field effect transistor Type A1 Journal article
Year 2011 Publication Journal of computational electronics Abbreviated Journal J Comput Electron
Volume 10 Issue (up) 1 Pages 216-221
Keywords A1 Journal article; Theory of quantum systems and complex systems; Condensed Matter Theory (CMT)
Abstract In this work we investigate quantum ballistic transport in ultrasmall junctionless and inversion mode semiconducting nanowire transistors within the framework of the self-consistent Schrödinger-Poisson problem. The quantum transmitting boundary method is used to generate open boundary conditions between the active region and the electron reservoirs. We adopt a subband decomposition approach to make the problem numerically tractable and make a comparison of four different numerical approaches to solve the self-consistent Schrödinger-Poisson problem. Finally we discuss the IV-characteristics for small (r≤5 nm) GaAs nanowire transistors. The novel junctionless pinch-off FET or junctionless nanowire transistor is extensively compared with the gate-all-around (GAA) nanowire MOSFET.
Address
Corporate Author Thesis
Publisher Place of Publication S.l. Editor
Language Wos 000300735800021 Publication Date 2011-02-22
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1569-8025;1572-8137; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 1.526 Times cited 12 Open Access
Notes ; ; Approved Most recent IF: 1.526; 2011 IF: 1.211
Call Number UA @ lucian @ c:irua:89501 Serial 2772
Permanent link to this record
 

 
Author Baelus, B.J.; Kanda, A.; Vodolazov, D.Y.; Ootuka, Y.; Peeters, F.
Title Quasi-one-dimensional vortex in an asymmetric superconducting ring Type A1 Journal article
Year 2007 Publication Physica: C : superconductivity Abbreviated Journal Physica C
Volume 460 Issue (up) 1 Pages 320-321
Keywords A1 Journal article; Condensed Matter Theory (CMT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos 000249870500088 Publication Date 2007-04-18
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0921-4534; ISBN Additional Links UA library record; WoS full record
Impact Factor 1.404 Times cited Open Access
Notes Approved Most recent IF: 1.404; 2007 IF: 1.079
Call Number UA @ lucian @ c:irua:66611 Serial 2798
Permanent link to this record
 

 
Author Delabie, A.; Sioncke, S.; Rip, J.; Van Elshocht, S.; Pourtois, G.; Mueller, M.; Beckhoff, B.; Pierloot, K.
Title Reaction mechanisms for atomic layer deposition of aluminum oxide on semiconductor substrates Type A1 Journal article
Year 2012 Publication Journal of vacuum science and technology: A: vacuum surfaces and films Abbreviated Journal J Vac Sci Technol A
Volume 30 Issue (up) 1 Pages 01a127-01a127,10
Keywords A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Abstract In this work, we have studied the TMA/H(2)O (TMA Al(CH(3))(3)) atomic layer deposition (ALD) of Al(2)O(3) on hydroxyl (OH) and thiol (SH) terminated semiconductor substrates. Total reflection x-ray fluorescence reveals a complex growth-per-cycle evolution during the early ALD reaction cycles. OH and SH terminated surfaces demonstrate growth inhibition from the second reaction cycle on. Theoretical calculations, based on density functional theory, are performed on cluster models to investigate the first TMA/H(2)O reaction cycle. Based on the theoretical results, we discuss possible mechanisms for the growth inhibition from the second reaction cycle on. In addition, our calculations show that AlCH(3) groups are hydrolyzed by a H(2)O molecule adsorbed on a neighboring Al atom, independent of the type of backbonds (Si-O, Ge-O, or Ge-S) of AlCH(3). The coordination of Al remains four-fold after the first TMA/H(2)O reaction cycle. (C) 2012 American Vacuum Society. [DOI: 10.1116/1.3664090]
Address
Corporate Author Thesis
Publisher Place of Publication New York, N.Y. Editor
Language Wos 000298992800027 Publication Date 2011-12-02
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0734-2101; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 1.374 Times cited 41 Open Access
Notes Approved Most recent IF: 1.374; 2012 IF: 1.432
Call Number UA @ lucian @ c:irua:96253 Serial 2818
Permanent link to this record
 

 
Author Norén, L.; Van Tendeloo, G.; Withers, R.L.
Title The real (incommensurate interface modulated) structure of Ni6\pm xSe5 Type A1 Journal article
Year 2001 Publication Journal of solid state chemistry Abbreviated Journal J Solid State Chem
Volume 162 Issue (up) 1 Pages 122-127
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication London Editor
Language Wos 000172586400016 Publication Date 2002-09-18
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0022-4596; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 2.299 Times cited 4 Open Access
Notes Approved Most recent IF: 2.299; 2001 IF: 1.614
Call Number UA @ lucian @ c:irua:54709 Serial 2826
Permanent link to this record
 

 
Author Malladi, S.K.; Xu, Q.; van Huis, M.A.; Tichelaar, F.D.; Batenburg, K.J.; Yucelen, E.; Dubiel, B.; Czyrska-Filemonowicz, A.; Zandbergen, H.W.
Title Real-time atomic scale imaging of nanostructural evolution in aluminum alloys Type A1 Journal article
Year 2014 Publication Nano Letters Abbreviated Journal Nano Lett
Volume 14 Issue (up) 1 Pages 384-389
Keywords A1 Journal article; Electron microscopy for materials research (EMAT); Vision lab
Abstract We present a new approach to study the three-dimensional compositional and structural evolution of metal alloys during heat treatments such as commonly used for improving overall material properties. It relies on in situ heating in a high-resolution scanning transmission electron microscope (STEM). The approach is demonstrated using a commercial Al alloy AA2024 at 100-240 degrees C, showing in unparalleled detail where and how precipitates nucleate, grow,or dissolve. The observed size evolution of individual precipitates enables a separation between nucleation and growth phenomena, necessary for the development of refined growth models. We conclude that the in situ heating STEM approach opens a route to a much faster determination of the interplay between local compositions, heat treatments, microstructure, and mechanical properties of new alloys.
Address
Corporate Author Thesis
Publisher Place of Publication Washington Editor
Language Wos 000329586700061 Publication Date 2013-12-13
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1530-6984;1530-6992; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 12.712 Times cited 12 Open Access
Notes Approved Most recent IF: 12.712; 2014 IF: 13.592
Call Number UA @ lucian @ c:irua:114789 Serial 2833
Permanent link to this record
 

 
Author Zelaya, E.; Schryvers, D.
Title Reducing the formation of FIB-induced FCC layers on Cu-Zn-Al austenite Type A1 Journal article
Year 2011 Publication Microscopy research and technique Abbreviated Journal Microsc Res Techniq
Volume 74 Issue (up) 1 Pages 84-91
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract The irradiation effects of thinning a sample of a Cu-Zn-Al shape memory alloy to electron transparency by a Ga+ focused ion beam were investigated. This thinning method was compared with conventional electropolishing and Ar+ ion milling. No implanted Ga was detected but surface FCC precipitation was found as a result of the focused ion beam sample preparation. Decreasing the irradiation dose by lowering the energy and current of the Ga+ ions did not lead to a complete disappearance of the FCC structure. The latter could only be removed after gentle Ar+ ion milling of the sample. It was further concluded that the precipitation of the FCC is independent of the crystallographic orientation of the surface.
Address
Corporate Author Thesis
Publisher Place of Publication New York, N.Y. Editor
Language Wos 000285976000012 Publication Date 2010-05-25
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1059-910X; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 1.147 Times cited 2 Open Access
Notes Approved Most recent IF: 1.147; 2011 IF: 1.792
Call Number UA @ lucian @ c:irua:85994 Serial 2852
Permanent link to this record
 

 
Author Müller, K.; Schowalter, M.; Rosenauer, A.; Jansen, J.; Tsuda, K.; Titantah, J.T.; Lamoen, D.
Title Refinement of chemically sensitive structure factors using parallel and convergent beam electron nanodiffraction Type A1 Journal article
Year 2010 Publication Journal of physics : conference series Abbreviated Journal
Volume 209 Issue (up) 1 Pages 012025-012025,4
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract We introduce a new method to measure structure factors from parallel beam electron diffraction (PBED) patterns. Bloch wave refinement routines were developed which can minimise the difference between simulated and experimental Bragg intensities via variation of structure factors, Debye parameters, specimen thickness and -orientation. Due to plane wave illumination, the PBED refinement is highly efficient not only in computational respect, but also concerning the experimental effort since energy filtering is shown to have no significant effect on the refinement results. The PBED method was applied to simulated GaAs diffraction patterns to derive systematic errors and rules for the identification of plausible refinement results. The evaluation of experimental GaAs PBED patterns yields a 200 X-ray structure factor of -6.33±0.14. Additionally, we obtained -6.35±0.13 from two-dimensional convergent beam electron diffraction refinements. Both results confirm density functional theory calculations published by Rosenauer et al. and indicate the inaccuracy of isolated atom scattering data, which is crucial e.g. for the composition evaluation by lattice fringe analysis.
Address
Corporate Author Thesis
Publisher Place of Publication Bristol Editor
Language Wos Publication Date 2010-02-27
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1742-6596; ISBN Additional Links UA library record
Impact Factor Times cited Open Access
Notes Approved Most recent IF: NA
Call Number UA @ lucian @ c:irua:85761 Serial 2855
Permanent link to this record
 

 
Author Philippaerts, A.; Paulussen, S.; Turner, S.; Lebedev, O.I.; Van Tendeloo, G.; Poelman, H.; Bulut, M.; de Clippel, F.; Smeets, P.; Sels, B.; Jacobs, P.
Title Selectivity in sorption and hydrogenation of methyl oleate and elaidate on MFI zeolites Type A1 Journal article
Year 2010 Publication Journal of catalysis Abbreviated Journal J Catal
Volume 270 Issue (up) 1 Pages 172-184
Keywords A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Abstract Different zeolites were tested for selective removal of methyl elaidate (trans isomer) from an equimolar mixture with methyl oleate (cis isomer). Sorption experiments of the geometric isomers show that only ZSM-5 samples with reduced Al content in the framework are able to discriminate among the bent cis and the linear trans fatty acid methyl esters. Hydrogenation experiments of equimolar methyl oleate and elaidate mixtures at low temperature (65 °C) and high hydrogen pressure (6.0 MPa), using Pt catalysts, confirm this result. Only with a Pt/NaZSM-5 catalyst outspoken selectivity for the hydrogenation of the trans isomer is obtained. In order to prepare a selective Pt/ZSM-5 catalyst, the influence of Pt addition (impregnation, ion-exchange and competitive ion-exchange) and Pt activation (different calcination and reduction temperatures) on the Pt-distribution and Pt particle size was investigated using SEM, bright-field and HR TEM, EDX, electron tomography, CO-chemisorption, XPS, XRD, and UVvis measurements. The best result in terms of hydrogenation activity and selectivity is obtained with a Pt/ZSM-5 catalyst, which is prepared via competitive ion-exchange, followed by slow calcination up to 350 °C under high O2 flow and a reduction up to 500 °C under H2. This preparation method leads to a Pt/ZSM-5 catalyst with the best Pt distribution and the smallest Pt clusters occluded in the zeolite structure. Finally, the influence of zeolite crystal size, morphology, and elemental composition of ZSM-5 on hydrogenation activity and selectivity was investigated in detail.
Address
Corporate Author Thesis
Publisher Place of Publication San Diego, Calif. Editor
Language Wos 000275966100021 Publication Date 2010-01-28
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0021-9517; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 6.844 Times cited 24 Open Access
Notes FWO; IAP-IV; Methusalem Approved Most recent IF: 6.844; 2010 IF: 5.415
Call Number UA @ lucian @ c:irua:82435 Serial 2970
Permanent link to this record
 

 
Author Shanenko, A.A.; Croitoru, M.D.
Title Shape resonances in the superconducting order parameter of ultrathin nanowires Type A1 Journal article
Year 2006 Publication Physical review : B : condensed matter and materials physics Abbreviated Journal Phys Rev B
Volume 73 Issue (up) 1 Pages 012510,1-4
Keywords A1 Journal article; Condensed Matter Theory (CMT); Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Lancaster, Pa Editor
Language Wos 000235009000033 Publication Date 2006-01-17
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1098-0121;1550-235X; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 3.836 Times cited 41 Open Access
Notes Approved Most recent IF: 3.836; 2006 IF: 3.107
Call Number UA @ lucian @ c:irua:56613 Serial 2990
Permanent link to this record
 

 
Author Saniz, R.; Xu, Y.; Matsubara, M.; Amini, M.N.; Dixit, H.; Lamoen, D.; Partoens, B.
Title A simplified approach to the band gap correction of defect formation energies : Al, Ga, and In-doped ZnO Type A1 Journal article
Year 2013 Publication The journal of physics and chemistry of solids Abbreviated Journal J Phys Chem Solids
Volume 74 Issue (up) 1 Pages 45-50
Keywords A1 Journal article; Electron microscopy for materials research (EMAT); Condensed Matter Theory (CMT)
Abstract The calculation of defect levels in semiconductors within a density functional theory approach suffers greatly from the band gap problem. We propose a band gap correction scheme that is based on the separation of energy differences in electron addition and relaxation energies. We show that it can predict defect levels with a reasonable accuracy, particularly in the case of defects with conduction band character, and yet is simple and computationally economical. We apply this method to ZnO doped with group III elements (Al, Ga, In). As expected from experiment, the results indicate that Zn substitutional doping is preferred over interstitial doping in Al, Ga, and In-doped ZnO, under both zinc-rich and oxygen-rich conditions. Further, all three dopants act as shallow donors, with the +1 charge state having the most advantageous formation energy. Also, doping effects on the electronic structure of ZnO are sufficiently mild so as to affect little the fundamental band gap and lowest conduction bands dispersion, which secures their n-type transparent conducting behavior. A comparison with the extrapolation method based on LDA+U calculations and with the HeydScuseriaErnzerhof hybrid functional (HSE) shows the reliability of the proposed scheme in predicting the thermodynamic transition levels in shallow donor systems.
Address
Corporate Author Thesis
Publisher Place of Publication New York, N.Y. Editor
Language Wos 000311062500009 Publication Date 2012-08-10
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0022-3697; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 2.059 Times cited 36 Open Access
Notes Fwo; Bof-Nio Approved Most recent IF: 2.059; 2013 IF: 1.594
Call Number UA @ lucian @ c:irua:101782 Serial 3004
Permanent link to this record
 

 
Author Ding, F.; Li, B.; Akopian, N.; Perinetti, U.; Chen, Y.H.; Peeters, F.M.; Rastelli, A.; Zwiller, V.; Schmidt, O.G.
Title Single neutral excitons confined in AsBr3 in situ etched InGaAs quantum rings Type A1 Journal article
Year 2011 Publication Journal of nanoelectronics and optoelectronics Abbreviated Journal J Nanoelectron Optoe
Volume 6 Issue (up) 1 Pages 51-57
Keywords A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT)
Abstract We observe the evolution of single self-assembled semiconductor quantum dots into quantum rings during AsBr3 in situ etching. The direct three-dimensional imaging of In(Ga)As nanostructures embedded in GaAs matrix is demonstrated by selective wet chemical etching combined with atomic force microscopy. Single neutral excitons confined in these quantum rings are studied by magneto-photoluminescence. Oscillations in the exciton radiative recombination energy and in the emission intensity are observed under an applied magnetic field. Further, we demonstrate that the period of the oscillations can be tuned by a gate potential that modifies the exciton confinement. The experimental results, combined with calculations, indicate that the exciton Aharonov-Bohm effect may account for the observed effects.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000290692200005 Publication Date 2011-04-18
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1555-130X;1555-1318; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 0.497 Times cited 3 Open Access
Notes ; We acknowledge L. P. Kouwenhoven and Z. G. Wang for support, C. C. Bof Bufon, C. Deneke, V. Fomin, A. Govorov, S. Kiravittaya, and Wen-Hao Chang for their help and discussions. We are grateful for the financial support of NWO (VIDI), the CAS-MPG programm, the DFG (FOR730), BMBF (No. 01BM459), NSFC China (60625402), and Flemish Science Foundation (FWO-V1). ; Approved Most recent IF: 0.497; 2011 IF: 0.556
Call Number UA @ lucian @ c:irua:90187 Serial 3025
Permanent link to this record
 

 
Author De Trizio, L.; Figuerola, A.; Manna, L.; Genovese, A.; George, C.; Brescia, R.; Saghi, Z.; Simonutti, R.; van Huis, M.; Falqui, A.
Title Size-tunable, hexagonal plate-like Cu3P and Janus-like Cu-Cu3P nanocrystals Type A1 Journal article
Year 2012 Publication ACS nano Abbreviated Journal Acs Nano
Volume 6 Issue (up) 1 Pages 32-41
Keywords A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Abstract We describe two synthesis approaches to colloidal Cu3P nanocrystals using trioctylphosphine (TOP) as phosphorus precursor. One approach is based on the homogeneous nucleation of small Cu3P nanocrystals with hexagonal plate-like morphology and with sizes that can be tuned from 5 to 50 nm depending on the reaction time. In the other approach, metallic Cu nanocrystals are nucleated first and then they are progressively phosphorized to Cu3P. In this case, intermediate Janus-like dimeric nanoparticles can be isolated, which are made of two domains of different materials, Cu and Cu3P, sharing a flat epitaxial interface. The Janus-like nanoparticles can be transformed back to single-crystalline copper particles if they are annealed at high temperature under high vacuum conditions, which makes them an interesting source of phosphorus. The features of the Cu Cu3P Janus-like nanoparticles are compared with those of the Wiped microstructure discovered more than two decades ago in the rapidly quenched Cu Cu3P eutectic of the Cu P alloy, suggesting that other alloy/eutectic systems that display similar behavior might give origin to nanostructures with flat, epitaxial Interface between domains of two diverse materials. Finally, the electrochemical properties of the copper phosphide plates are studied, and they are found to be capable of undergoing lithiation/delithiation through a displacement reaction, while the Janus-like Cu Cu3P particles do not display an electrochemical behavior that would make them suitable for applications in batteries.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000299368300006 Publication Date 2011-12-03
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1936-0851;1936-086X; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 13.942 Times cited 60 Open Access
Notes Approved Most recent IF: 13.942; 2012 IF: 12.062
Call Number UA @ lucian @ c:irua:99172 Serial 3039
Permanent link to this record
 

 
Author Jones, L.; Yang, H.; Pennycook, T.J.; Marshall, M.S.J.; Van Aert, S.; Browning, N.D.; Castell, M.R.; Nellist, P.D.
Title Smart Align : a new tool for robust non-rigid registration of scanning microscope data Type A1 Journal article
Year 2015 Publication Advanced Structural and Chemical Imaging Abbreviated Journal
Volume 1 Issue (up) 1 Pages 8
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Many microscopic investigations of materials may benefit from the recording of multiple successive images. This can include techniques common to several types of microscopy such as frame averaging to improve signal-to-noise ratios (SNR) or time series to study dynamic processes or more specific applications. In the scanning transmission electron microscope, this might include focal series for optical sectioning or aberration measurement, beam damage studies or camera-length series to study the effects of strain; whilst in the scanning tunnelling microscope, this might include bias-voltage series to probe local electronic structure. Whatever the application, such investigations must begin with the careful alignment of these data stacks, an operation that is not always trivial. In addition, the presence of low-frequency scanning distortions can introduce intra-image shifts to the data. Here, we describe an improved automated method of performing non-rigid registration customised for the challenges unique to scanned microscope data specifically addressing the issues of low-SNR data, images containing a large proportion of crystalline material and/or local features of interest such as dislocations or edges. Careful attention has been paid to artefact testing of the non-rigid registration method used, and the importance of this registration for the quantitative interpretation of feature intensities and positions is evaluated.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000218507000008 Publication Date 2015-07-09
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 2198-0926; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor Times cited 131 Open Access
Notes 312483 Esteem2; esteem2_jra2 Approved Most recent IF: NA
Call Number c:irua:126944 c:irua:126944 Serial 3043
Permanent link to this record
 

 
Author Nelissen, K.; Matulis, A.; Partoens, B.; Kong, M.; Peeters, F.M.
Title Spectrum of classical two-dimensional Coulomb clusters Type A1 Journal article
Year 2006 Publication Physical review : E : statistical physics, plasmas, fluids, and related interdisciplinary topics Abbreviated Journal Phys Rev E
Volume 73 Issue (up) 1 Pages 016607,1-7
Keywords A1 Journal article; Condensed Matter Theory (CMT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Lancaster, Pa Editor
Language Wos 000235008800095 Publication Date 2006-01-17
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1539-3755;1550-2376; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 2.366 Times cited 33 Open Access
Notes Approved Most recent IF: 2.366; 2006 IF: 2.438
Call Number UA @ lucian @ c:irua:56611 Serial 3075
Permanent link to this record
 

 
Author Fang, C.M.; van Huis, M.A.; Zandbergen, H.W.
Title Stability and structures of the CFCC-TmC phases : a first-principles study Type A1 Journal article
Year 2012 Publication Computational materials science Abbreviated Journal Comp Mater Sci
Volume 51 Issue (up) 1 Pages 146-150
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract The η-M6C, γ-M23C6, and π-M11C2 phases (M = Cr, Mn and Fe) have complex cubic lattices with lattice parameters of approximately 1.0 nm. They belong to the CFCC-TmC family (complex face-centered cubic transition metal carbides), display a rich variety of crystal structures, and play in important role in iron alloys and steels. Here we show that first-principles calculations predict high stability for the γ-M23C6 and η-M6C phases, and instability for the π-M11C2 phases, taking into account various compositional and structural possibilities. The calculations also show a wide variety in magnetic properties. The Cr-containing phases were found to be non-magnetic and the Fe-phases to be ferromagnetic, while the Mn-containing phases were found to be either ferrimagnetic or non-magnetic. Details of the local atomic structures, and the formation and stability of these precipitates in alloys are discussed.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000296214300020 Publication Date 2011-08-29
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0927-0256; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 2.292 Times cited 18 Open Access
Notes Approved Most recent IF: 2.292; 2012 IF: 1.878
Call Number UA @ lucian @ c:irua:93277 Serial 3119
Permanent link to this record
 

 
Author Rauwel, E.; Dubourdieu, C.; Holländer, B.; Rochat, N.; Ducroquet, F.; Rossell, M.D.; Van Tendeloo, G.; Pelissier, B.
Title Stabilization of the cubic phase of HfO2 by Y addition in films grown by metal organic chemical vapor deposition Type A1 Journal article
Year 2006 Publication Applied physics letters Abbreviated Journal Appl Phys Lett
Volume 89 Issue (up) 1 Pages 012902,1-012902,3
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Addition of yttrium in HfO(2) thin films prepared on silicon by metal organic chemical vapor deposition is investigated in a wide compositional range (2.0-99.5 at. %). The cubic structure of HfO(2) is stabilized for 6.5 at. %. The permittivity is maximum for yttrium content of 6.5-10 at. %; in this range, the effective permittivity, which results from the contribution of both the cubic phase and silicate phase, is of 22. These films exhibit low leakage current density (5x10(-7) A/cm(2) at -1 V for a 6.4 nm film). The cubic phase is stable upon postdeposition high temperature annealing at 900 degrees C under NH(3). (c) 2006 American Institute of Physics.
Address
Corporate Author Thesis
Publisher American Institute of Physics Place of Publication New York, N.Y. Editor
Language Wos 000238849200046 Publication Date 2006-07-06
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0003-6951; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 3.411 Times cited 78 Open Access
Notes Medea T207 Approved Most recent IF: 3.411; 2006 IF: 3.977
Call Number UA @ lucian @ c:irua:59632 Serial 3138
Permanent link to this record
 

 
Author Scalise, E.; Houssa, M.; Pourtois, G.; Afanas'ev, V.; Stesmans, A.
Title Strain-induced semiconductor to metal transition in the two-dimensional honeycomb structure of MoS2 Type A1 Journal article
Year 2012 Publication Nano Research Abbreviated Journal Nano Res
Volume 5 Issue (up) 1 Pages 43-48
Keywords A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Abstract The electronic properties of two-dimensional honeycomb structures of molybdenum disulfide (MoS(2)) subjected to biaxial strain have been investigated using first-principles calculations based on density functional theory. On applying compressive or tensile bi-axial strain on bi-layer and mono-layer MoS(2), the electronic properties are predicted to change from semiconducting to metallic. These changes present very interesting possibilities for engineering the electronic properties of two-dimensional structures of MoS(2).
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000299085200006 Publication Date 2011-11-10
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1998-0124;1998-0000; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 7.354 Times cited 407 Open Access
Notes Approved Most recent IF: 7.354; 2012 IF: 7.392
Call Number UA @ lucian @ c:irua:96262 Serial 3169
Permanent link to this record
 

 
Author Ferreira, W.P.; Carvalho, J.C.N.; Oliveira, P.W.S.; Farias, G.A.; Peeters, F.M.
Title Structural and dynamical properties of a quasi-one-dimensional classical binary system Type A1 Journal article
Year 2008 Publication Physical review : B : condensed matter and materials physics Abbreviated Journal Phys Rev B
Volume 77 Issue (up) 1 Pages 014112,1-11
Keywords A1 Journal article; Condensed Matter Theory (CMT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Lancaster, Pa Editor
Language Wos 000252862200028 Publication Date 2008-01-31
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1098-0121;1550-235X; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 3.836 Times cited 20 Open Access
Notes Approved Most recent IF: 3.836; 2008 IF: 3.322
Call Number UA @ lucian @ c:irua:67816 Serial 3194
Permanent link to this record
 

 
Author Dombrovski, E.N.; Serov, T.V.; Abakumov, A.M.; Ardashnikova, E.I.; Dolgikh, V.A.; Van Tendeloo, G.
Title The structural investigation of Ba4Bi3F17 Type A1 Journal article
Year 2004 Publication Journal of solid state chemistry Abbreviated Journal J Solid State Chem
Volume 177 Issue (up) 1 Pages 312-318
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication London Editor
Language Wos 000188534800041 Publication Date 2003-11-20
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0022-4596; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 2.299 Times cited 9 Open Access
Notes Approved Most recent IF: 2.299; 2004 IF: 1.815
Call Number UA @ lucian @ c:irua:54717 Serial 3239
Permanent link to this record
 

 
Author Milat, O.; Van Tendeloo, G.; Amelinckx, S.; Babu, T.G.N.; Greaves, C.
Title Structural variants of Ca0.85CuO2(Ca5+xCu6O12) Type A1 Journal article
Year 1992 Publication Journal of solid state chemistry Abbreviated Journal J Solid State Chem
Volume 101 Issue (up) 1 Pages 92-114
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract The structure of Ca0.85CuO2 was reexamined by means of electron diffraction and electron microscopy using the newly developed method of selective imaging in intergrowth structures in which the two substructures are based on different sublattices. The results of previous work are confirmed. Moreover, it is shown that two stacking variants and their twin related structures occur in the calcium substructure. The copper-oxygen substructure occurs in one variant only; it is often modulated by the various calcium arrangements, leading to phase disorder in its modulation pattern. It is shown that the ribbons of CuO4 clusters are presumably tilted with respect to the (010) plane.
Address
Corporate Author Thesis
Publisher Place of Publication London Editor
Language Wos A1992JW94200012 Publication Date 2006-06-12
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0022-4596; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 2.133 Times cited 10 Open Access
Notes Approved
Call Number UA @ lucian @ c:irua:103021 Serial 3272
Permanent link to this record
 

 
Author Berdiyorov, G.R.; Milošević, M.V.; Peeters, F.M.
Title The structure and manipulation of vortex states in a superconducting square with 2 × 2 blind holes Type A1 Journal article
Year 2005 Publication Journal of low temperature physics Abbreviated Journal J Low Temp Phys
Volume 139 Issue (up) 1 Pages 229-238
Keywords A1 Journal article; Condensed Matter Theory (CMT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication New York Editor
Language Wos 000228853900021 Publication Date 2005-04-29
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0022-2291;1573-7357; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 1.3 Times cited 4 Open Access
Notes Approved Most recent IF: 1.3; 2005 IF: 0.753
Call Number UA @ lucian @ c:irua:57246 Serial 3284
Permanent link to this record
 

 
Author ben Azzouz, F.; Zouaoui, M.; Mani, K.D.; Annabi, M.; Van Tendeloo, G.; ben Salem, M.
Title Structure, microstructure and transport properties of B-doped YBCO system Type A1 Journal article
Year 2006 Publication Physica: C : superconductivity Abbreviated Journal Physica C
Volume 442 Issue (up) 1 Pages 13-19
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos 000238756600003 Publication Date 2006-05-19
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0921-4534; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 1.404 Times cited 14 Open Access
Notes Approved Most recent IF: 1.404; 2006 IF: 0.792
Call Number UA @ lucian @ c:irua:59712 Serial 3304
Permanent link to this record
 

 
Author Morozov, V.A.; Lazoryak, B.I.; Lebedev, O.I.; Amelinckx, S.; Van Tendeloo, G.
Title Structures of three polymorphs of the complex oxide K5Yb(MoO4)4 Type A1 Journal article
Year 2003 Publication Journal of solid state chemistry Abbreviated Journal J Solid State Chem
Volume 176 Issue (up) 1 Pages 76-87
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication London Editor
Language Wos 000186711300012 Publication Date 2003-10-09
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0022-4596; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 2.299 Times cited 8 Open Access
Notes Approved Most recent IF: 2.299; 2003 IF: 1.413
Call Number UA @ lucian @ c:irua:54716 Serial 3322
Permanent link to this record
 

 
Author Milat, O.; Van Tendeloo, G.; Amelinckx, S.; Babu, T.G.N.; Greaves, C.
Title Superstructure and structural variants in Sr2CuO2(CO3) Type A1 Journal article
Year 1994 Publication Journal of solid state chemistry Abbreviated Journal J Solid State Chem
Volume 109 Issue (up) 1 Pages 5-14
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication London Editor
Language Wos A1994MY48800002 Publication Date 2002-09-18
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0022-4596; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 2.133 Times cited 11 Open Access
Notes Approved PHYSICS, APPLIED 28/145 Q1 #
Call Number UA @ lucian @ c:irua:99919 Serial 3384
Permanent link to this record
 

 
Author Verberck, B.
Title Symmetry-adapted rotator functions for molecules in cylindrical confinement Type A1 Journal article
Year 2011 Publication International journal of molecular sciences Abbreviated Journal Int J Mol Sci
Volume 12 Issue (up) 1 Pages 317-333
Keywords A1 Journal article; Condensed Matter Theory (CMT)
Abstract We present a general description of the formalism of symmetry-adapted rotator functions (SARFs) for molecules in cylindrical confinement. Molecules are considered as clusters of interaction centers (ICs), can have any symmetry, and can display different types of ICs. Cylindrical confinement can be realized by encapsulation in a carbon nanotube (CNT). The potential energy of a molecule surrounded by a CNT can be calculated by evaluating a limited number of terms of an expansion into SARFs, which offers a significant reduction of the computation time. Optimal molecular orientations can be deduced from the resulting potential energy landscape. Examples, including the case of a molecule with cubic symmetry inside a CNT, are discussed.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000286583400017 Publication Date 2011-01-13
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1422-0067; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 3.226 Times cited 1 Open Access
Notes ; ; Approved Most recent IF: 3.226; 2011 IF: NA
Call Number UA @ lucian @ c:irua:88048 Serial 3402
Permanent link to this record
 

 
Author Lin, K.; Pescarmona, P.P.; Vandepitte, H.; Liang, D.; Van Tendeloo, G.; Jacobs, P.A.
Title Synthesis and catalytic activity of Ti-MCM-41 nanoparticles with highly active titanium sites Type A1 Journal article
Year 2008 Publication Journal of catalysis Abbreviated Journal J Catal
Volume 254 Issue (up) 1 Pages 64-70
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Ti-MCM-41 nanoparticles 80-160 nm in diameter (Ti-MCM-41 NP) were successfully prepared by a dilute solution route in sodium hydroxide medium at ambient temperature. Ti-MCM-41 NP were characterized by X-ray diffraction, nitrogen adsorption/desorption isotherms, SEM, TEM. FT-IR, and UV-vis spectroscopy. The characterization results showed the existence of highly ordered hexagonal mesoporous structure and tetrahedral Ti species in Ti-MCM-41 NP. In the epoxidation of cyclohexene with aqueous H2O2, Ti-MCM-41 NP displayed higher conversion and initial reaction rate than a Ti-MCM-41 sample with normal particle size (Ti-MCM-41 LP). Diffusion of the reactants was accelerated and the accessibility to the catalytic Ti species was enhanced in the shorter channels in Ti-MCM-41 NP samples. Ti-MCM-41 NP showed much higher selectivity for cyclohexene oxide compared with Ti-MCM-41 LP, suggesting reduced hydrolysis of cyclohexene oxide with water in the former case. The increased selectivity for cyclohexene oxide can be attributed to the lower concentration of residual surface silanols in Ti-MCM-41 NP and the shorter residence time of epoxide in the shorter mesoporous channels. Ti-MCM-41 NP also appears to be a suitable catalyst in the epoxidation of a bulky substrate, like cholesterol, with tert-butyl hydroperoxide. (c) 2007 Elsevier Inc. All rights reserved.
Address
Corporate Author Thesis
Publisher Place of Publication San Diego, Calif. Editor
Language Wos 000253646100006 Publication Date 2008-01-30
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0021-9517; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 6.844 Times cited 52 Open Access
Notes Approved Most recent IF: 6.844; 2008 IF: 5.167
Call Number UA @ lucian @ c:irua:103092 Serial 3409
Permanent link to this record