| Home | << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 >> |
|
| Records | |||||
|---|---|---|---|---|---|
Author  |
Leenaerts, O.; Vercauteren, S.; Partoens, B. | ||||
| Title | Band alignment of lateral two-dimensional heterostructures with a transverse dipole | Type | A1 Journal article | ||
| Year | 2017 | Publication | Applied physics letters | Abbreviated Journal | Appl Phys Lett |
| Volume | 110 | Issue | 110 | Pages | 181602 |
| Keywords | A1 Journal article; Condensed Matter Theory (CMT) | ||||
| Abstract | It was recently shown that the electronic band alignment in lateral two-dimensional heterostructures is strongly dependent on the system geometry, such as heterostructure width and layer thickness. This is so even in the absence of polar edge terminations because of the appearance of an interface dipole between the two different materials. In this study, this work is expanded to include two-dimensional materials that possess an electronic dipole over their surface, i.e., in the direction transverse to the crystal plane. To this end, a heterostucture consisting of polar hydrofluorinated graphene and non-polar graphane layers is studied with first-principles calculations. As for nonpolar heterostructures, a significant geometry dependence is observed with two different limits for the band offset. For infinitely wide heterostructures, the potential step in the vacuum is equally divided over the two sides of the heterostructure, resulting in a finite potential step in the heterostructure. For infinitely thick heterostructure slabs, on the other hand, the band offset is reduced, similar to the three-dimensional case. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | American Institute of Physics | Place of Publication | New York, N.Y. | Editor | |
| Language | Wos | 000400931900014 | Publication Date | 2017-05-01 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0003-6951; 1077-3118 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.411 | Times cited | 4 | Open Access | |
| Notes | ; This work was supported by the Fonds Wetenschappelijk Onderzoek (FWO-VI). The computational resources and services used in this work were provided by the VSC (Flemish Supercomputer Center), funded by the Hercules Foundation and the Flemish Government-department EWI. ; | Approved | Most recent IF: 3.411 | ||
| Call Number | UA @ lucian @ c:irua:143755 | Serial | 4586 | ||
| Permanent link to this record | |||||
| Author |
Leenaerts, O.; Partoens, B.; Peeters, F.M.; Volodin, A.; van Haesendonck, C. | ||||
| Title | The work function of few-layer graphene | Type | A1 Journal article | ||
| Year | 2017 | Publication | Journal of physics : condensed matter | Abbreviated Journal | |
| Volume | 29 | Issue | 3 | Pages | 035003 |
| Keywords | A1 Journal article; Condensed Matter Theory (CMT) | ||||
| Abstract | A theoretical and experimental study of the work function of few-layer graphene is reported. The influence of the number of layers on the work function is investigated in the presence of a substrate, a molecular dipole layer, and combinations of the two. The work function of few-layer graphene is almost independent of the number of layers with only a difference between monolayer and multilayer graphene of about 60 meV. In the presence of a charge-donating substrate the charge distribution is found to decay exponentially away from the substrate and this is directly reflected in the work function of few-layer graphene. A dipole layer changes the work function only when placed in between the substrate and few-layer graphene through a change of the charge transfer between the two. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000425250600002 | Publication Date | 2016-11-16 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0953-8984 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | Times cited | 61 | Open Access | ||
| Notes | Approved | no | |||
| Call Number | UA @ admin @ c:irua:164938 | Serial | 8760 | ||
| Permanent link to this record | |||||
| Author |
Lander, L.; Rousse, G.; Batuk, D.; Colin, C.V.; Dalla Corte, D.A.; Tarascon, J.-M. | ||||
| Title | Synthesis, structure, and electrochemical properties of k-based sulfates K2M2(SO4)3) with M = Fe and Cu | Type | A1 Journal article | ||
| Year | 2017 | Publication | Inorganic chemistry | Abbreviated Journal | Inorg Chem |
| Volume | 56 | Issue | 4 | Pages | 2013-2021 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Stabilizing new host structures through potassium extraction from K-based polyanionic materials has been proven to be an interesting approach to develop new Li+/Na+ insertion materials. Pursuing the same trend, we here report the feasibility of preparing langbeinite “Fe-2(SO4)(3)” via electrochemical and chemical oxidation of K2Fe2(SO4)(3). Additionally, we succeeded in stabilizing a new K2Cu2(SO4)(3) phase via a solid-state synthesis approach. This novel compound crystallizes in a complex orthorhombic structure that differs from that of langbeinite as deduced from synchrotron X-ray and neutron powder diffraction. Electrochemically, the performance of this new phase is limited, which we explain in terms of sluggish diffusion kinetics. We further show that K2Cu2(SO4)(3) decomposes into K2Cu3O(SO4)(3) on heating, and we report for the first time the synthesis of fedotovite K2Cu3O(SO4)(3). Finally, the fundamental attractiveness of these S = 1/2 systems for physicists is examined by neutron magnetic diffraction, which reveals the absence of a long-range ordering of Cu2+ magnetic moments down to 1.5 K. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Easton, Pa | Editor | ||
| Language | Wos | 000394736600027 | Publication Date | 2017-01-27 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0020-1669 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 4.857 | Times cited | 13 | Open Access | Not_Open_Access |
| Notes | ; We thank Matthieu Courty for performing TGA/DSC measurements. Use of the 11-BM mail service of the APS at Argonne National Laboratory was supported by the U.S. Department of Energy under Contract DE-AC02-06CH11357 and is acknowledged. The French CRG D1B is acknowledged for allocating neutron beamtime. L.L. thanks the ANR “Hipolite” for the Ph.D. funding. ; | Approved | Most recent IF: 4.857 | ||
| Call Number | UA @ lucian @ c:irua:142531 | Serial | 4692 | ||
| Permanent link to this record | |||||
| Author |
Lambrinou, K.; Charalampopoulou, E.; Van der Donck, T.; Delville, R.; Schryvers, D. | ||||
| Title | Dissolution corrosion of 316L austenitic stainless steels in contact with static liquid lead-bismuth eutectic (LBE) at 500 °C | Type | A1 Journal article | ||
| Year | 2017 | Publication | Journal of nuclear materials | Abbreviated Journal | J Nucl Mater |
| Volume | 490 | Issue | 490 | Pages | 9-27 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
| Abstract | This work addresses the dissolution corrosion behaviour of 316L austenitic stainless steels. For this purpose, solution-annealed and cold-deformed 316L steels were simultaneously exposed to oxygen-poor (<10-8 mass%) static liquid lead-bismuth eutectic (LBE) for 253e3282 h at 500 °C. Corrosion was consistently more severe for the cold-drawn steels than the solution-annealed steel, indicating the importance of the steel thermomechanical state. The thickness of the dissolution-affected zone was nonuniform, and sites of locally-enhanced dissolution were occasionally observed. The progress of LBE dissolution attack was promoted by the interplay of certain steel microstructural features (grain boundaries, deformation twin laths, precipitates) with the dissolution corrosion process. The identified dissolution mechanisms were selective leaching leading to steel ferritization, and non-selective leaching; the latter was mainly observed in the solution-annealed steel. The maximum corrosion rate decreased with exposure time and was found to be inversely proportional to the depth of dissolution attack. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000403132300002 | Publication Date | 2017-04-10 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0022-3115 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 2.048 | Times cited | 24 | Open Access | OpenAccess |
| Notes | The authors would like to acknowledge the following 316L stainless steel suppliers: Industeel, ArcelorMittal Group, for the 316LSA plate procured and characterised in the FP6 EUROTRANSDEMETRA project (Contract no. FI6W-CT-2004-516520); OLARRA Aceros Inoxidables, Spain, for the 316LH1 rod; and SIDERO STAAL nv, Belgium, for the 316LH2 rod. K. Lambrinou would like to thank J. Joris for technical support during the launching and follow up of all corrosion tests, J. Lim for the manufacturing and calibration of the oxygen sensors used in these tests, T. Lapauw for the XRD measurements on the pristine steels, and S. Van den Broeck for the FIB sample preparation. Special thanks to S. Gavrilov for fruitful and intense discussions. The authors gratefully acknowledge the funding provided in the framework of the ongoing development of the MYRRHA irradiation facility. The research leading to these results falls within the framework of the European Energy Research Alliance Joint Programme on Nuclear Materials (EERA JPNM). | Approved | Most recent IF: 2.048 | ||
| Call Number | EMAT @ emat @ c:irua:142644 | Serial | 4563 | ||
| Permanent link to this record | |||||
| Author |
Kus, M.; Altantzis, T.; Vercauteren, S.; Caretti, I.; Leenaerts, O.; Batenburg, K.J.; Mertens, M.; Meynen, V.; Partoens, B.; Van Doorslaer, S.; Bals, S.; Cool, P. | ||||
| Title | Mechanistic Insight into the Photocatalytic Working of Fluorinated Anatase {001} Nanosheets | Type | A1 Journal article | ||
| Year | 2017 | Publication | The journal of physical chemistry: C : nanomaterials and interfaces | Abbreviated Journal | J Phys Chem C |
| Volume | 121 | Issue | 121 | Pages | 26275-26286 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Condensed Matter Theory (CMT); Laboratory of adsorption and catalysis (LADCA) | ||||
| Abstract | Anatase nanosheets with exposed {001} facets have gained increasing interest for photocatalytic applications. To fully understand the structure-to-activity relation, combined experimental and computational methods have been exploited. Anatase nanosheets were prepared under hydrothermal conditions in the presence of fluorine ions. High resolution scanning transmission electron microscopy was used to fully characterize the synthesized material, confirming the TiO2 nanosheet morphology. Moreover, the surface structure and composition of a single nanosheet could be determined by annular bright-field scanning transmission electron microscopy (ABF-STEM) and STEM electron energy loss spectroscopy (STEM-EELS). The photocatalytic activity was tested for the decomposition of organic dyes rhodamine 6G and methyl orange and compared to a reference TiO2 anatase sample. The anatase nanosheets with exposed {001} facets revealed a significantly lower photocatalytic activity compared to the reference. In order to understand the mechanism for the catalytic performance, and to investigate the role of the presence of F−, light-induced electron paramagnetic resonance (EPR) experiments were performed. The EPR results are in agreement with TEM, proving the presence of Ti3+ species close to the surface of the sample and allowing the analysis of the photoinduced formation of paramagnetic species. Further, ab initio calculations of the anisotropic effective mass of electrons and electron holes in anatase show a very high effective mass of electrons in the [001] direction, having a negative impact on the mobility of electrons toward the {001} surface and thus the photocatalysis. Finally, motivated by the experimental results that indicate the presence of fluorine atoms at the surface, we performed ab initio calculations to determine the position of the band edges in anatase slabs with different terminations of the {001} surface. The presence of fluorine atoms near the surface is shown to strongly shift down the band edges, which indicates another reason why it can be expected that the prepared samples with a large amount of {001} surface, but with fluorine atoms near the surface, show only a low photocatalytic activity. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000417228500017 | Publication Date | 2017-11-30 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1932-7447 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 4.536 | Times cited | 20 | Open Access | OpenAccess |
| Notes | The authors acknowledge the University of Antwerp for financial support in the frame of a GOA project. S.B. acknowledges funding from the European Research Council under the Seventh Framework Program (FP7), ERC Grant No. 335078 COLOURATOM. S.V.D. and V.M. acknowledge funding from the Fund for Scientific Research-Flanders (G.0687.13). T.A. acknowledges financial support from the Research Foundation Flanders (FWO, Belgium) through a postdoctoral grant. (ROMEO:white; preprint:; postprint:restricted 12 months embargo; pdfversion:cannot); saraecas; ECAS_Sara; | Approved | Most recent IF: 4.536 | ||
| Call Number | EMAT @ emat @c:irua:147240UA @ admin @ c:irua:147240 | Serial | 4771 | ||
| Permanent link to this record | |||||
| Author |
Kurttepeli, M.; Deng, S.; Mattelaer, F.; Cott, D.J.; Vereecken, P.; Dendooven, J.; Detavernier, C.; Bals, S. | ||||
| Title | Heterogeneous TiO2/V2O5/Carbon Nanotube Electrodes for Lithium-Ion Batteries | Type | A1 Journal article | ||
| Year | 2017 | Publication | ACS applied materials and interfaces | Abbreviated Journal | Acs Appl Mater Inter |
| Volume | 9 | Issue | 9 | Pages | 8055-8064 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Vanadium pentoxide (V2O5) is proposed and investigated as a cathode material for lithium-ion (Li-ion) batteries. However, the dissolution of V2O5 during the charge/discharge remains as an issue at the V2O5–electrolyte interface. In this work, we present a heterogeneous nanostructure with carbon nanotubes supported V2O5/titanium dioxide (TiO2) multilayers as electrodes for thin-film Li-ion batteries. Atomic layer deposition of V2O5 on carbon nanotubes provides enhanced Li storage capacity and high rate performance. An additional TiO2 layer leads to increased morphological stability and in return higher electrochemical cycling performance of V2O5/carbon nanotubes. The physical and chemical properties of TiO2/V2O5/carbon nanotubes are characterized by cyclic voltammetry and charge/discharge measurements as well as electron microscopy. The detailed mechanism of the protective TiO2 layer to improve the electrochemical cycling stability of the V2O5 is unveiled. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000396186000021 | Publication Date | 2017-03-08 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1944-8244 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 7.504 | Times cited | 28 | Open Access | OpenAccess |
| Notes | European Research Council, 239865 335078 ; Fonds Wetenschappelijk Onderzoek; Agentschap voor Innovatie door Wetenschap en Technologie, 18142 ; Bijzonder Onderzoeksfonds, GOA – 01G01513 ; This research was funded by the Flemish research foundation FWO-Vlaanderen, by the European Research Council (Starting Grant No. 239865 and No. 335078), by IWT-Flanders (SBO project IWT 18142 “SoS-Lion”) and by the Special Research Fund BOF of Ghent University (GOA – 01G01513); colouratoms (ROMEO:white; preprint:; postprint:restricted 12 months embargo; pdfversion:cannot); ECAS_Sara | Approved | Most recent IF: 7.504 | ||
| Call Number | EMAT @ emat @ c:irua:142446UA @ admin @ c:irua:142446 | Serial | 4572 | ||
| Permanent link to this record | |||||
| Author |
Kumar, A.; Kundu, S.; Samantaray, D.; Kundu, P.; Zanaga, D.; Bals, S.; Ravishankar, N. | ||||
| Title | Designing diameter-modulated heterostructure nanowires of PbTe/Te by controlled dewetting | Type | A1 Journal article | ||
| Year | 2017 | Publication | Nano letters | Abbreviated Journal | Nano Lett |
| Volume | 17 | Issue | 17 | Pages | 7226-7233 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
| Abstract | <script type='text/javascript'>document.write(unpmarked('Heterostructures consisting of semiconductors with controlled morphology and interfaces find applications in many fields. A range of axial, radial, and diameter-modulated nanostructures have been synthesized primarily using vapor phase methods. Here, we present a simple wet chemical routine to synthesize heterostructures of PbTe/Te using Te nanowires as templates. A morphology evolution study for the formation of these heterostructures has been performed. On the basis of these control experiments, a pathway for the formation of these nanostructures is proposed. Reduction of a Pb precursor to Pb on Te nanowire templates followed by interdiffusion of Pb/Te leads to the formation of a thin shell of PbTe on the Te wires. Controlled dewetting of the thin shell leads to the formation of cube-shaped PbTe that is periodically arranged on the Te wires. Using control experiments, we show that different reactions parameters like rate of addition of the reducing agent, concentration of Pb precursor and thickness of initial Te nanowire play a critical role in controlling the spacing between the PbTe cubes on the Te wires. Using simple surface energy arguments, we propose a mechanism for the formation of the hybrid. The principles presented are general and can be exploited for the synthesis of other nanoscale heterostructures.')); | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Washington | Editor | ||
| Language | Wos | 000418393300009 | Publication Date | 2017-11-29 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1530-6984 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 12.712 | Times cited | 11 | Open Access | OpenAccess |
| Notes | ; N.R acknowledges financial support from SERB, DST, Government of India. The authors acknowledge the electron microscopy facilities at the Advanced Facility for Microscopy and Microanalysis, IISc. S.B., P.K., and D.Z. acknowledge ERC Starting Grant 335078 COLOURATOMS for financial support. ; ecas_Sara | Approved | Most recent IF: 12.712 | ||
| Call Number | UA @ lucian @ c:irua:148557UA @ admin @ c:irua:148557 | Serial | 4870 | ||
| Permanent link to this record | |||||
| Author |
Kong, X.; Li, L.; Leenaerts, O.; Liu, X.-J.; Peeters, F.M. | ||||
| Title | New group-V elemental bilayers : a tunable structure model with four-, six-, and eight-atom rings | Type | A1 Journal article | ||
| Year | 2017 | Publication | Physical review B | Abbreviated Journal | Phys Rev B |
| Volume | 96 | Issue | 3 | Pages | 035123 |
| Keywords | A1 Journal article; Condensed Matter Theory (CMT) | ||||
| Abstract | Two-dimensional group-V elemental materials have attracted widespread attention due to their nonzero band gap while displaying high electron mobility. Using first-principles calculations, we propose a series of new elemental bilayers with group-V elements (Bi, Sb, As). Our study reveals the dynamical stability of four-, six-, and eight-atom ring structures, demonstrating their possible coexistence in such bilayer systems. The proposed structures for Sb and As are large-gap semiconductors that are potentially interesting for applications in future nanodevices. The Bi structures have nontrivial topological properties with a direct nontrivial band gap. The nontrivial gap is shown to arise from a band inversion at the Brillouin zone center due to the strong intrinsic spin-orbit coupling in Bi atoms. Moreover, we demonstrate the possibility of tuning the properties of these materials by enhancing the ratio of six-atom rings to four-and eight-atom rings, which results in wider nontrivial band gaps and lower formation energies. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | American Physical Society | Place of Publication | New York, N.Y | Editor | |
| Language | Wos | 000405363900005 | Publication Date | 2017-07-14 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2469-9969; 2469-9950 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.836 | Times cited | 14 | Open Access | |
| Notes | ; This work is supported by Ministry of Science and Technology of China (MOST) (Grant No. 2016YFA0301604), National Natural Science Foundation of China (NSFC) ( No. 11574008), the Thousand-Young-Talent Program of China, and the Fonds voor Wetenschappelijk Onderzoek (FWO-Vl). The computational resources and services used in this work were provided by the VSC (Flemish Supercomputer Center), funded by the Research Foundation – Flanders (FWO) and the Flemish Government – department EWI, and the National Supercomputing Center in Tianjin, funded by the Collaborative Innovation Center of Quantum Matter. ; | Approved | Most recent IF: 3.836 | ||
| Call Number | UA @ lucian @ c:irua:144834 | Serial | 4721 | ||
| Permanent link to this record | |||||
| Author |
Kong, L.; Wang, W.; Murphy, A.B.; Xia, G. | ||||
| Title | Numerical analysis of direct-current microdischarge for space propulsion applications using the particle-in-cell/Monte Carlo collision (PIC/MCC) method | Type | A1 Journal article | ||
| Year | 2017 | Publication | Journal of physics: D: applied physics | Abbreviated Journal | J Phys D Appl Phys |
| Volume | 50 | Issue | 16 | Pages | 165203 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Microdischarges are an important type of plasma discharge that possess several unique characteristics, such as the presence of a stable glow discharge, high plasma density and intense excimer radiation, leading to several potential applications. The intense and controllable gas heating within the extremely small dimensions of microdischarges has been exploited in microthruster technologies by incorporating a micro-nozzle to generate the thrust. This kind of microthruster has a significantly improved specific impulse performance compared to conventional cold gas thrusters, and can meet the requirements arising from the emerging development and application of micro-spacecraft. In this paper, we performed a self-consistent 2D particle-in-cell simulation, with a Monte Carlo collision model, of a microdischarge operating in a prototype micro-plasma thruster with a hollow cylinder geometry and a divergent micro-nozzle. The model takes into account the thermionic electron emission including the Schottky effect, the secondary electron emission due to cathode bombardment by the plasma ions, several different collision processes, and a non-uniform argon background gas density in the cathode-anode gap. Results in the high-pressure (several hundreds of Torr), high-current (mA) operating regime showing the behavior of the plasma density, potential distribution, and energy flux towards the hollow cathode and anode are presented and discussed. In addition, the results of simulations showing the effect of different argon gas pressures, cathode material work function and discharge voltage on the operation of the microdischarge thruster are presented. Our calculated properties are compared with experimental data under similar conditions and qualitative and quantitative agreements are reached. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | London | Editor | ||
| Language | Wos | 000398856300001 | Publication Date | 2017-02-22 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0022-3727 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 2.588 | Times cited | 8 | Open Access | OpenAccess |
| Notes | Approved | Most recent IF: 2.588 | |||
| Call Number | UA @ lucian @ c:irua:143642 | Serial | 4674 | ||
| Permanent link to this record | |||||
| Author |
Kolev, S.; Sun, S.; Trenchev, G.; Wang, W.; Wang, H.; Bogaerts, A. | ||||
| Title | Quasi-Neutral Modeling of Gliding Arc Plasmas: Quasi-Neutral Modeling of Gliding Arc Plasmas | Type | A1 Journal article | ||
| Year | 2017 | Publication | Plasma processes and polymers | Abbreviated Journal | Plasma Process Polym |
| Volume | 14 | Issue | 14 | Pages | 1600110 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | The modelling of a gliding arc discharge (GAD) is studied by means of the quasineutral (QN) plasma modelling approach. The model is first evaluated for reliability and proper description of a gliding arc discharge at atmospheric pressure, by comparing with a more elaborate non-quasineutral (NQN) plasma model in two different geometries – a 2D axisymmetric and a Cartesian geometry. The NQN model is considered as a reference, since it provides a continuous self-consistent plasma description, including the near electrode regions. In general, the results of the QN model agree very well with those obtained from the NQN model. The small differences between both models are attributed to the approximations in the derivation of the QN model. The use of the QN model provides a substantial reduction of the computation time compared to the NQN model, which is crucial for the development of more complex models in three dimensions or with complicated chemistries. The latter is illustrated for (i) a reverse vortex flow(RVF) GAD in argon, and (ii) a GAD in CO2. The RVF discharge is modelled in three dimensions and the effect of the turbulent heat transport on the plasma and gas characteristics is discussed. The GAD model in CO2 is in a 1D geometry with axial symmetry and provides results for the time evolution of the electron, gas and vibrational temperature of CO2, as well as for the molar fractions of the different species. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000403074000011 | Publication Date | 2016-10-04 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1612-8850 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 2.846 | Times cited | 9 | Open Access | Not_Open_Access |
| Notes | Methusalem financing of the University of Antwerp; | Approved | Most recent IF: 2.846 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:142982 | Serial | 4570 | ||
| Permanent link to this record | |||||
| Author |
Koelman, P.; Heijkers, S.; Tadayon Mousavi, S.; Graef, W.; Mihailova, D.; Kozak, T.; Bogaerts, A.; van Dijk, J. | ||||
| Title | A Comprehensive Chemical Model for the Splitting of CO2in Non-Equilibrium Plasmas: A Comprehensive Chemical Model for CO2Splitting | Type | A1 Journal article | ||
| Year | 2017 | Publication | Plasma processes and polymers | Abbreviated Journal | Plasma Process Polym |
| Volume | 14 | Issue | 14 | Pages | 1600155 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | An extensive CO2 plasmamodel is presented that is relevant for the production of ‘‘solar fuels.’’ It is based on reaction rate coefficients fromrigorously reviewed literature, and is augmented with reactionrate coefficients that are obtained fromscaling laws.The input data set,which is suitable for usage with the plasma simulation software Plasimo (https://plasimo.phys.tue.nl/), is available via the Plasimo and publisher’s websites.1 The correctness of this model implementation has been established by independent ZDPlasKin implementation (http://www.zdplaskin. laplace.univ-tlse.fr/), to verify that the results agree. Results of these ‘‘global models’’ are presented for a DBD plasma reactor. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000403074000009 | Publication Date | 2016-10-17 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1612-8850 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 2.846 | Times cited | 21 | Open Access | Not_Open_Access |
| Notes | Dutch Technology Foundation STW; Ministerie van Economische Zaken; Hercules Foundation; Acknowledgements: This research is supported by the Dutch Technology Foundation STW, which is part of the Netherlands Organization for Scientific Research (NWO), and which is partly funded by the Ministry of Economic Affairs. Furthermore, we acknowledge financial support from the IAP/7 (Inter-university Attraction Pole) program PSI-Physical Chemistry of Plasma- Surface Interactions by the Belgian Federal Office for Science Policy (BELSPO). Part of the calculations were carried out using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UAntwerpen), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UAntwerpen. | Approved | Most recent IF: 2.846 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:142643 | Serial | 4565 | ||
| Permanent link to this record | |||||
| Author |
Klinkhammer, C.; Verlackt, C.; Smilowicz, D.; Kogelheide, F.; Bogaerts, A.; Metzler-Nolte, N.; Stapelmann, K.; Havenith, M.; Lackmann, J.-W. | ||||
| Title | Elucidation of plasma-induced chemical modifications on glutathione and glutathione disulphide | Type | A1 Journal article | ||
| Year | 2017 | Publication | Scientific reports | Abbreviated Journal | Sci Rep-Uk |
| Volume | 7 | Issue | Pages | 13828 | |
| Keywords | A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Cold atmospheric pressure plasmas are gaining increased interest in the medical sector and clinical trials to treat skin diseases are underway. Plasmas are capable of producing several reactive oxygen and nitrogen species (RONS). However, there are open questions how plasma-generated RONS interact on a molecular level in a biological environment, e.g. cells or cell components. The redox pair glutathione (GSH) and glutathione disulphide (GSSG) forms the most important redox buffer in organisms responsible for detoxification of intracellular reactive species. We apply Raman spectroscopy, mass spectrometry, and molecular dynamics simulations to identify the time-dependent chemical modifications on GSH and GSSG that are caused by dielectric barrier discharge under ambient conditions. We find GSSG, S-oxidised glutathione species, and S-nitrosoglutathione as oxidation products with the latter two being the final products, while glutathione sulphenic acid, glutathione sulphinic acid, and GSSG are rather reaction intermediates. Experiments using stabilized pH conditions revealed the same main oxidation products as were found in unbuffered solution, indicating that the dominant oxidative or nitrosative reactions are not influenced by acidic pH. For more complex systems these results indicate that too long treatment times can cause difficult-to-handle modifications to the cellular redox buffer which can impair proper cellular function. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Nature Publishing Group | Place of Publication | London | Editor | |
| Language | Wos | 000413401300003 | Publication Date | 2017-10-17 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2045-2322 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 4.259 | Times cited | 17 | Open Access | OpenAccess |
| Notes | Approved | Most recent IF: 4.259 | |||
| Call Number | UA @ lucian @ c:irua:146666 | Serial | 4783 | ||
| Permanent link to this record | |||||
| Author |
Kleibert, A.; Balan, A.; Yanes, R.; Derlet, P.M.; Vaz, C.A.F.; Timm, M.; Fraile Rodríguez, A.; Béché, A.; Verbeeck, J.; Dhaka, R.S.; Radovic, M.; Nowak, U.; Nolting, F. | ||||
| Title | Direct observation of enhanced magnetism in individual size- and shape-selected 3d transition metal nanoparticles | Type | A1 Journal article | ||
| Year | 2017 | Publication | Physical review B | Abbreviated Journal | Phys Rev B |
| Volume | 95 | Issue | 95 | Pages | 195404 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Magnetic nanoparticles are critical building blocks for future technologies ranging from nanomedicine to spintronics. Many related applications require nanoparticles with tailored magnetic properties. However, despite significant efforts undertaken towards this goal, a broad and poorly understood dispersion of magnetic properties is reported, even within monodisperse samples of the canonical ferromagnetic 3d transition metals. We address this issue by investigating the magnetism of a large number of size- and shape-selected, individual nanoparticles of Fe, Co, and Ni using a unique set of complementary characterization techniques. At room temperature, only superparamagnetic behavior is observed in our experiments for all Ni nanoparticles within the investigated sizes, which range from 8 to 20 nm. However, Fe and Co nanoparticles can exist in two distinct magnetic states at any size in this range: (i) a superparamagnetic state, as expected from the bulk and surface anisotropies known for the respective materials and as observed for Ni, and (ii) a state with unexpected stable magnetization at room temperature. This striking state is assigned to significant modifications of the magnetic properties arising from metastable lattice defects in the core of the nanoparticles, as concluded by calculations and atomic structural characterization. Also related with the structural defects, we find that the magnetic state of Fe and Co nanoparticles can be tuned by thermal treatment enabling one to tailor their magnetic properties for applications. This paper demonstrates the importance of complementary single particle investigations for a better understanding of nanoparticle magnetism and for full exploration of their potential for applications. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000400665300002 | Publication Date | 2017-05-05 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2469-9950 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.836 | Times cited | 21 | Open Access | OpenAccess |
| Notes | We thank A. Weber, R. Schelldorfer, and J. Krbanjevic (Paul Scherrer Institut) for technical assistance. This paper was supported by the Swiss Nanoscience Institute, University of Basel. A.F.R. acknowledges support from the MICIIN “Ramón y Cajal” Programme. A.B. and J.V. acknowledge funding from the European Union under the European Research Council (ERC) Starting Grant No. 278510 VORTEX and under a contract for Integrated Infrastructure Initiative ESTEEM2 No. 312483. R.Y. and U.N. thank the Deutsche Forschungsgemeinschaft for financial support via Sonderforschungsbereich 1214. Part of this work was performed at the Surface/Interface: Microscopy (SIM) beamline of the Swiss Light Source, Paul Scherrer Institut, Villigen, Switzerland. | Approved | Most recent IF: 3.836 | ||
| Call Number | EMAT @ emat @ c:irua:143634UA @ admin @ c:irua:143634 | Serial | 4575 | ||
| Permanent link to this record | |||||
| Author |
Kim, E.; Roosen, J.; Horckmans, L.; Spooren, J.; Broos, K.; Binnemans, K.; Vrancken, K.C.M.; Quaghebeur, M. | ||||
| Title | Process development for hydrometallurgical recovery of valuable metals from sulfide-rich residue generated in a secondary lead smelter | Type | A1 Journal article | ||
| Year | 2017 | Publication | Hydrometallurgy | Abbreviated Journal | |
| Volume | 169 | Issue | Pages | 589-598 | |
| Keywords | A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) | ||||
| Abstract | Two routes were investigated to selectively recover lead and minor metals (Cu, Ni, Zn) from a sulfide-rich lead smelter residue, matte. The first route comprises a two-step leaching process that combines Fe(III)-HNO3 leaching with roasting, followed by water leaching. In the first step, the efficiency of Pb leaching was 90% at the optimum condition (L/S ratio 8, 0.5 mol.L-1 HNO3, 0.15 mol.L-1 Fe(III), 25 degrees C). In the second step, roasting at 600 degrees C followed by water leaching at 50 degrees C selectively leached Ni, Cu, and Zn while fully converting iron sulfides to oxides. One-step oxidative pressure leaching in HNO3 was investigated as an alternative to simultaneously leach Pb, Cu, Ni and Zn. At the optimal conditions (130 degrees C, 60 min, 0.3 mol.L-1 HNO3, 0.07 mol.L-1 Fe(III), L/S ratio 20), Pb, Cu, Zn and Ni leaching were 92, 60, 70 and 66%, respectively, while Fe leaching remained low (2%). The leachates obtained from both leaching routes were treated by ion-exchange adsorption with diethylenetriaminepentaacetic acid (DTPA) functionalized chitosan-silica hybrid materials to investigate the selective recovery of Cu, Zn and Ni. The adsorption order appeared to be in the same order as the corresponding stability constants for complexes between the respective metal ions and free DTPA: Ca(II) < Zn(II) < Pb (II) approximate to Ni(II) < Cu(II). This allows not only to selectively recover Cu, Zn and Ni from the leachates, but also to mutually separate them by using the functionalized resin as a stationary phase in column chromatography. To avoid adsorbent contamination, Fe(III) and Pb(II) may be removed from the leachates in a pre-treatment step. Based on these results, the investigated methods can be combined as process steps of two possible routes for the selective recovery of valuable metals from the studied secondary lead smelting residue. The two-step leaching process seems to be superior since a more concentrated solution of Cu, Ni, and Zn is produced in the 2nd leaching step with low capital cost. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000401878200070 | Publication Date | 2017-04-03 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0304-386x | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | Times cited | Open Access | |||
| Notes | Approved | no | |||
| Call Number | UA @ admin @ c:irua:144300 | Serial | 8414 | ||
| Permanent link to this record | |||||
| Author |
Kim, E.; Horckmans, L.; Spooren, J.; Vrancken, K.C.; Quaghebeur, M.; Broos, K. | ||||
| Title | Selective leaching of Pb, Cu, Ni and Zn from secondary lead smelting residues | Type | A1 Journal article | ||
| Year | 2017 | Publication | Hydrometallurgy | Abbreviated Journal | |
| Volume | 169 | Issue | Pages | 372-381 | |
| Keywords | A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) | ||||
| Abstract | Several HNO3-based leaching approaches were tested and optimized to selectively recover Pb and other minor metals (Cu, Ni, Zn) from secondary lead smelter residues (i.e., slag and matte). Firstly, the leaching behaviors of Pb and the matrix element Fe were studied at atmospheric pressure in the temperature range 25-70 degrees C. These elements were present in both materials studied as sulfide and oxide phases. For the sulfur-rich matte residue, the Pb leaching increased from 63% to 69% upon increasing the HNO3 concentration from 0.2 M to 0.5 M. However, by adding Fe(III) as an oxidation agent, Pb leaching from the matte amounted to 90% at 25 degrees C. At a higher temperature, Pb leaching was reduced due to PbSO4 precipitation. In this process, Cu, Zn and Ni leaching was insignificant. For the slag residue, HNO3 could not leach Pb (0.03% Pb leached), while Fe leaching was 19.8% due to a galvanic effect. However, Pb leaching of the slag was 82% in the presence of additional Fe(III). Secondly, to enhance leaching of the other base metals (Cu, Zn and Ni) from the matte, roasting followed by water leaching and (microwave assisted or autoclave) pressurized leaching in 0.5 M HNO3 were applied. During roasting, the FeS phase converted to Fe2O3 above 500 degrees C, and PbS and Pb phases were transformed into insoluble PbSO4 above 400 degrees C. Cu, Ni and Zn leaching was drastically enhanced by a roasting step at 600 degrees C followed by leaching with 0.5 M HNO3 at 50 degrees C, or by pressurized HNO3 leaching above 130 degrees C, whereby Pb leaching almost ceased due to PbSO4 precipitation. During the roasting above 600 degrees C, or microwave assisted extraction (MAE) at 160 degrees C for 15 min, FeS was completely converted to iron oxides that can be used as raw material for pig iron production. Based on the results, the methods investigated can be combined as process steps of two possible routes for the selective recovery of valuable metals and the production of a clean source of Fe oxides from the secondary lead smelting residues studied. (C) 2017 Elsevier B.V. All rights reserved. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000401878200045 | Publication Date | 2017-03-02 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0304-386x | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | Times cited | Open Access | |||
| Notes | Approved | no | |||
| Call Number | UA @ admin @ c:irua:144299 | Serial | 8503 | ||
| Permanent link to this record | |||||
| Author |
Kim, E.; Horckmans, L.; Spooren, J.; Broos, K.; Vrancken, K.C.M.; Quaghebeur, M. | ||||
| Title | Recycling of a secondary lead smelting matte by selective citrate leaching of valuable metals and simultaneous recovery of hematite as a secondary resource | Type | A1 Journal article | ||
| Year | 2017 | Publication | Hydrometallurgy | Abbreviated Journal | |
| Volume | 169 | Issue | Pages | 290-296 | |
| Keywords | A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) | ||||
| Abstract | Anew recycling process, according to the zero-waste concept, was investigated for an iron rich waste stream, more specifically a secondary lead smelting matte. The process consists of a selective citrate leaching of Pb, Cu, Ni and Zn in combination with a roasting step, leading to a simultaneous recovery of hematite as a secondary iron resource. The parameters, such as leaching time, leaching temperature, H2O2 concentration and roasting temperature, were experimentally optimized. The maximum Pb leaching efficiency was 93% and the leachability of Cu (33%) and Zn (11%) increased slightly in the presence of 0.5 M H2O2 in 1 M citrate at 25 degrees C and pH 5.5. Importantly, almost no Fe was leached (< 0.6%) from the iron rich matrix material at this condition allowing for a maximal recovery of hematite as a secondary resource after further treatment (i.e. roasting or sulfur removal). The leachability of Pb, Cu, Ni and Zn was strongly affected by the roasting temperature. Maximum leaching efficiency in 1 M citrate (25 degrees C, L/S ratio 10, pH 6.5) was 93% for Pb, 80% for Cu and 60% for Zn at a roasting temperature of 600 degrees C, while for Ni the maximum leaching efficiency of 53% was reached after roasting at 650 degrees C. Furthermore, when oxidative roasting was applied, the leaching residue consists dominantly of hematite (Fe2O3) with minor quantities of PbSO4, which can be used as pig iron ore (Fe > 60 wt%). (C) 2017 Elsevier B.V. All rights reserved. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000401878200035 | Publication Date | 2017-02-14 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0304-386x | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | Times cited | Open Access | |||
| Notes | Approved | no | |||
| Call Number | UA @ admin @ c:irua:144298 | Serial | 8463 | ||
| Permanent link to this record | |||||
| Author |
Khalilov, U.; Bogaerts, A.; Xu, B.; Kato, T.; Kaneko, T.; Neyts, E.C. | ||||
| Title | How the alignment of adsorbed ortho H pairs determines the onset of selective carbon nanotube etching | Type | A1 Journal article | ||
| Year | 2017 | Publication | Nanoscale | Abbreviated Journal | Nanoscale |
| Volume | 9 | Issue | 9 | Pages | 1653-1661 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Unlocking the enormous technological potential of carbon nanotubes strongly depends on our ability to specifically produce metallic or semiconducting tubes. While selective etching of both has already been demonstrated, the underlying reasons, however, remain elusive as yet. We here present computational and experimental evidence on the operative mechanisms at the atomic scale. We demonstrate that during the adsorption of H atoms and their coalescence, the adsorbed ortho hydrogen pairs on single-walled carbon nanotubes induce higher shear stresses than axial stresses, leading to the elongation of HC–CH bonds as a function of their alignment with the tube chirality vector, which we denote as the γ-angle. As a result, the C–C cleavage occurs more rapidly in nanotubes containing ortho H-pairs with a small γ-angle. This phenomenon can explain the selective etching of small-diameter semiconductor nanotubes with a similar curvature. Both theoretical and experimental results strongly indicate the important role of the γ-angle in the selective etching mechanisms of carbon nanotubes, in addition to the nanotube curvature and metallicity effects and lead us to clearly understand the onset of selective synthesis/removal of CNT-based materials. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000395422800036 | Publication Date | 2016-12-19 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2040-3364 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 7.367 | Times cited | 6 | Open Access | OpenAccess |
| Notes | U. K. gratefully acknowledges financial support from the Fund of Scientific Research Flanders (FWO), Belgium (Grant No. 12M1315N). This work was also supported in part by Grant-in- Aid for Young Scientists A (Grant No. 25706028), Grant-in-Aid for Scientific Research on Innovative Areas (Grant No. 26107502) from JSPS KAKENHI. This work was carried out in part using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UA), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UA. The authors also thank Prof. A. C. T. van Duin for sharing the ReaxFF code and J. Razzokov for his assistance to perform the DFT calculations. | Approved | Most recent IF: 7.367 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:140091 | Serial | 4417 | ||
| Permanent link to this record | |||||
| Author |
Khalilov, U.; Bogaerts, A.; Neyts, E.C. | ||||
| Title | Atomic-scale mechanisms of plasma-assisted elimination of nascent base-grown carbon nanotubes | Type | A1 Journal article | ||
| Year | 2017 | Publication | Carbon | Abbreviated Journal | Carbon |
| Volume | 118 | Issue | 118 | Pages | 452-457 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Selective etching allows for obtaining carbon nanotubes with a specific chirality. While plasma-assisted etching has already been used to separate metallic tubes from their semiconducting counterparts, little is known about the nanoscale mechanisms of the etching process. We combine (reactive) molecular dynamics (MD) and force-bias Monte Carlo (tfMC) simulations to study H-etching of CNTs. In particular, during the hydrogenation and subsequent etching of both the carbon cap and the tube, they sequentially transform to different carbon nanostructures, including carbon nanosheet, nanowall, and polyyne chains, before they are completely removed from the surface of a substrate-bound Ni-nanocluster.We also found that onset of the etching process is different in the cases of the cap and the tube, although the overall etching scenario is similar in both cases. The entire hydrogenation/etching process for both cases is analysed in detail, comparing with available theoretical and experimental evidences. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000401120800053 | Publication Date | 2017-03-26 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0008-6223 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 6.337 | Times cited | 2 | Open Access | OpenAccess |
| Notes | U. K. gratefully acknowledges financial support from the Research Foundation – Flanders (FWO), Belgium (Grant No. 12M1315N). The work was carried out in part using the Turing HPC infrastructure of the CalcUA core facility of the Universiteit Antwerpen, a division of the Flemish Supercomputer Centre VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the Universiteit Antwerpen. The authors also thank Prof. A. C. T. van Duin for sharing the ReaxFF code. | Approved | Most recent IF: 6.337 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:141915 | Serial | 4531 | ||
| Permanent link to this record | |||||
| Author |
Khalilov, U.; Bogaerts, A.; Neyts, E.C. | ||||
| Title | Toward the Understanding of Selective Si Nano-Oxidation by Atomic Scale Simulations | Type | A1 Journal article | ||
| Year | 2017 | Publication | Accounts of chemical research | Abbreviated Journal | Accounts Chem Res |
| Volume | 50 | Issue | 50 | Pages | 796-804 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | The continuous miniaturization of nanodevices, such as transistors, solar cells, and optical fibers, requires the controlled synthesis of (ultra)thin gate oxides (<10 nm), including Si gate-oxide (SiO2) with high quality at the atomic scale. Traditional thermal growth of SiO2 on planar Si surfaces, however, does not allow one to obtain such ultrathin oxide due to either the high oxygen diffusivity at high temperature or the very low sticking ability of incident oxygen at low temperature. Two recent techniques, both operative at low (room) temperature, have been put forward to overcome these obstacles: (i) hyperthermal oxidation of planar Si surfaces and (ii) thermal or plasma-assisted oxidation of nonplanar Si surfaces, including Si nanowires (SiNWs). These nanooxidation processes are, however, often difficult to study experimentally, due to the key intermediate processes taking place on the nanosecond time scale. In this Account, these Si nano-oxidation techniques are discussed from a computational point of view and compared to both hyperthermal and thermal oxidation experiments, as well as to well-known models of thermal oxidation, including the Deal−Grove, Cabrera−Mott, and Kao models and several alternative mechanisms. In our studies, we use reactive molecular dynamics (MD) and hybrid MD/Monte Carlo simulation techniques, applying the Reax force field. The incident energy of oxygen species is chosen in the range of 1−5 eV in hyperthermal oxidation of planar Si surfaces in order to prevent energy-induced damage. It turns out that hyperthermal growth allows for two growth modes, where the ultrathin oxide thickness depends on either (1) only the kinetic energy of the incident oxygen species at a growth temperature below Ttrans = 600 K, or (2) both the incident energy and the growth temperature at a growth temperature above Ttrans. These modes are specific to such ultrathin oxides, and are not observed in traditional thermal oxidation, nor theoretically considered by already existing models. In the case of thermal or plasma-assisted oxidation of small Si nanowires, on the other hand, the thickness of the ultrathin oxide is a function of the growth temperature and the nanowire diameter. Below Ttrans, which varies with the nanowire diameter, partially oxidized SiNW are formed, whereas complete oxidation to a SiO2 nanowire occurs only above Ttrans. In both nano-oxidation processes at lower temperature (T < Ttrans), final sandwich c-Si|SiOx|a-SiO2 structures are obtained due to a competition between overcoming the energy barrier to penetrate into Si subsurface layers and the compressive stress (∼2−3 GPa) at the Si crystal/oxide interface. The overall atomic-simulation results strongly indicate that the thickness of the intermediate SiOx (x < 2) region is very limited (∼0.5 nm) and constant irrespective of oxidation parameters. Thus, control over the ultrathin SiO2 thickness with good quality is indeed possible by accurately tuning the oxidant energy, oxidation temperature and surface curvature. In general, we discuss and put in perspective these two oxidation mechanisms for obtaining controllable ultrathin gate-oxide films, offering a new route toward the fabrication of nanodevices via selective nano-oxidation. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000399859800016 | Publication Date | 2017-04-18 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0001-4842 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 20.268 | Times cited | 5 | Open Access | OpenAccess |
| Notes | Fonds Wetenschappelijk Onderzoek, 12M1315N ; | Approved | Most recent IF: 20.268 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:142638 | Serial | 4561 | ||
| Permanent link to this record | |||||
| Author |
Khalilov, U.; Bogaerts, A.; Hussain, S.; Kovacevic, E.; Brault, P.; Boulmer-Leborgne, C.; Neyts, E.C. | ||||
| Title | Nanoscale mechanisms of CNT growth and etching in plasma environment | Type | A1 Journal article | ||
| Year | 2017 | Publication | Journal of physics: D: applied physics | Abbreviated Journal | J Phys D Appl Phys |
| Volume | 50 | Issue | 50 | Pages | 184001 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Plasma-enhanced chemical deposition (PECVD) of carbon nanotubes has already been shown to allow chirality control to some extent. In PECVD, however, etching may occur simultaneously with the growth, and the occurrence of intermediate processes further significantly complicates the growth process. We here employ a computational approach with experimental support to study the plasma-based formation of Ni nanoclusters, Ni-catalyzed CNT growth and subsequent etching processes, in order to understand the underpinning nanoscale mechanisms. We find that hydrogen is the dominant factor in both the re-structuring of a Ni film and the subsequent appearance of Ni nanoclusters, as well as in the CNT nucleation and etching processes. The obtained results are compared with available theoretical and experimental studies and provide a deeper understanding of the occurring nanoscale mechanisms in plasma-assisted CNT nucleation and growth. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000398300900001 | Publication Date | 2017-04-03 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0022-3727 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 2.588 | Times cited | 6 | Open Access | OpenAccess |
| Notes | UK gratefully acknowledges financial support from the Research Foundation – Flanders (FWO), Belgium (Grant No. 12M1315N). The work was carried out in part using the Turing HPC infrastructure of the CalcUA core facility of the Universiteit Antwerpen, a division of the Flemish Supercomputer Centre VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the Universiteit Antwerpen. The authors also thank Prof A C T van Duin for sharing the ReaxFF code. | Approved | Most recent IF: 2.588 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:141918 | Serial | 4533 | ||
| Permanent link to this record | |||||
| Author |
Keulemans, M. | ||||
| Title | Study of electron transfer processes in plasmonic photocatalysis | Type | Doctoral thesis | ||
| Year | 2017 | Publication | Abbreviated Journal | ||
| Volume | Issue | Pages | 170 p. | ||
| Keywords | Doctoral thesis; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) | ||||
| Abstract | |||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | Publication Date | |||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | ISBN | Additional Links | UA library record | ||
| Impact Factor | Times cited | Open Access | |||
| Notes | Approved | no | |||
| Call Number | UA @ admin @ c:irua:147504 | Serial | 8596 | ||
| Permanent link to this record | |||||
| Author |
Kertik, A.; Wee, L.H.; Pfannmöller, M.; Bals, S.; Martens, J.A.; Vankelecom, I.F.J. | ||||
| Title | Highly selective gas separation membrane using in situ amorphised metal-organic frameworks | Type | A1 Journal article | ||
| Year | 2017 | Publication | Energy & environmental science | Abbreviated Journal | Energ Environ Sci |
| Volume | 10 | Issue | 10 | Pages | 2342-2351 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Conventional carbon dioxide (CO2) separation in the petrochemical industry via cryogenic distillation is energy intensive and environmentally unfriendly. Alternatively, polymer membrane-based separations are of significant interest owing to low production cost, low-energy consumption and ease of upscaling. However, the implementation of commercial polymeric membranes is limited by their permeability and selectivity trade-off and the insufficient thermal and chemical stability. Herein, a novel type of amorphous mixed matrix membrane (MMM) able to separate CO2/CH4 mixtures with the highest selectivities ever reported for MOF based MMMs is presented. The MMM consists of an amorphised metal-organic framework (MOF) dispersed in an oxidatively cross-linked matrix achieved by fine tuning of the thermal treatment temperature in air up to 350 degrees C which drastically boosts the separation properties of the MMM. Thanks to the protection of the surrounding polymer, full oxidation of this MOF (i.e. ZIF-8) is prevented, and amorphisation of the MOF is realized instead, thus in situ creating a molecular sieve network. In addition, the treatment also improves the filler-polymer adhesion and induces an oxidative cross-linking of the polyimide matrix, resulting in MMMs with increased stability or plasticization resistance at high pressure up to 40 bar, marking a new milestone as new molecular sieve MOF MMMs for challenging natural gas purification applications. A new field for the use of amorphised MOFs and a variety of separation opportunities for such MMMs are thus opened. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000414774500007 | Publication Date | 2017-08-09 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1754-5692; 1754-5706 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 29.518 | Times cited | 122 | Open Access | OpenAccess |
| Notes | ; A.K. acknowledges financial support from the Erasmus-Mundus Doctorate in Membrane Engineering (EUDIME) Programme. L.H.W. thanks the FWO-Vlaanderen for a postdoctoral research fellowship (12M1415N). M. P. acknowledges financial support by the FP7 European project SUNFLOWER (FP7 #287594). S. B. acknowledges financial support from European Research Council (ERC Starting Grant # 335078-COLOURATOMS). J. A. M. gratefully acknowledges financial supports from the Flemish Government for long-term Methusalem funding. J. A. M. and I. F. J. V. acknowledge the Belgian Government for IAP-PAI networking. A. K. would also like to thank Frank Mathijs for the mechanical tests, Roy Bernstein for the XPS analysis and Lien Telen and Bart Goderis for the DSC measurements. We thank Verder Scientific Benelux for providing the service of ZIF-8 ball milling. ; ecas_sara | Approved | Most recent IF: 29.518 | ||
| Call Number | UA @ lucian @ c:irua:147399UA @ admin @ c:irua:147399 | Serial | 4879 | ||
| Permanent link to this record | |||||
| Author |
Kandemir, A.; Ozden, A.; Cagin, T.; Sevik, C. | ||||
| Title | Thermal conductivity engineering of bulk and one-dimensional Si-Ge nanoarchitectures | Type | A1 Journal article | ||
| Year | 2017 | Publication | Science and technology of advanced materials | Abbreviated Journal | |
| Volume | 18 | Issue | 1 | Pages | 187-196 |
| Keywords | A1 Journal article; Condensed Matter Theory (CMT) | ||||
| Abstract | Various theoretical and experimental methods are utilized to investigate the thermal conductivity of nanostructured materials; this is a critical parameter to increase performance of thermoelectric devices. Among these methods, equilibrium molecular dynamics (EMD) is an accurate technique to predict lattice thermal conductivity. In this study, by means of systematic EMD simulations, thermal conductivity of bulk Si-Ge structures (pristine, alloy and superlattice) and their nanostructured one dimensional forms with square and circular cross-section geometries (asymmetric and symmetric) are calculated for different crystallographic directions. A comprehensive temperature analysis is evaluated for selected structures as well. The results show that one-dimensional structures are superior candidates in terms of their low lattice thermal conductivity and thermal conductivity tunability by nanostructuring, such as by diameter modulation, interface roughness, periodicity and number of interfaces. We find that thermal conductivity decreases with smaller diameters or cross section areas. Furthermore, interface roughness decreases thermal conductivity with a profound impact. Moreover, we predicted that there is a specific periodicity that gives minimum thermal conductivity in symmetric superlattice structures. The decreasing thermal conductivity is due to the reducing phonon movement in the system due to the effect of the number of interfaces that determine regimes of ballistic and wave transport phenomena. In some nanostructures, such as nanowire superlattices, thermal conductivity of the Si/Ge system can be reduced to nearly twice that of an amorphous silicon thermal conductivity. Additionally, it is found that one crystal orientation, <100>, is better than the <111> crystal orientation in one-dimensional and bulk SiGe systems. Our results clearly point out the importance of lattice thermal conductivity engineering in bulk and nanostructures to produce high-performance thermoelectric materials. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000405949800001 | Publication Date | 2017-03-13 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1468-6996; 1878-5514 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | Times cited | Open Access | |||
| Notes | Approved | no | |||
| Call Number | UA @ admin @ c:irua:193772 | Serial | 8662 | ||
| Permanent link to this record | |||||
| Author |
Jouzi, Z.; Azadi, H.; Taheri, F.; Zarafshani, K.; Gebrehiwot, K.; Van Passel, S.; Lebailly, P. | ||||
| Title | Organic farming and small-scale farmers : main opportunities and challenges | Type | A1 Journal article | ||
| Year | 2017 | Publication | Ecological Economics | Abbreviated Journal | Ecol Econ |
| Volume | 132 | Issue | Pages | 144-154 | |
| Keywords | A1 Journal article; Economics; Engineering Management (ENM) | ||||
| Abstract | Producing enough food to meet the needs of a growing population has always been the greatest concern of food policy-makers around the world. Given the increasing attention to organic farming (OF), we conducted this study to investigate the main opportunities and challenges of the food production system of small-scale farmers in developing countries with an emphasis on their livelihoods. The study showed that the most significant advantages of OF are environmental protection and a higher resilience to environmental changes, increasing farmers' income and reducing external input cost, enhancing social capacity and increasing employment opportunities. A s well as enhancing food security primarily by increasing the food purchasing power of local people. However, the main challenges of this food production system include lower yields in comparison to conventional systems, difficulties with soil nutrient management, certification and market barriers, and the educational and research needs of small-holders. The paper concludes that even though OF might present some significant challenges to small-scale farmers, it could/should still be considered as a part of the solution and means of improving their livelihoods. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000390825200014 | Publication Date | 2016-11-06 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0921-8009; 1873-6106 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles; WoS full record; WoS citing articles | |
| Impact Factor | 2.965 | Times cited | 39 | Open Access | |
| Notes | ; ; | Approved | Most recent IF: 2.965 | ||
| Call Number | UA @ admin @ c:irua:139034 | Serial | 6233 | ||
| Permanent link to this record | |||||
| Author |
Jorli, M.; Van Passel, S.; Sadeghi, H.; Nasseri, A.; Agheli, L. | ||||
| Title | Estimating human health impacts and costs due to Iranian fossil fuel power plant emissions through the impact pathway approach | Type | A1 Journal article | ||
| Year | 2017 | Publication | Energies | Abbreviated Journal | Energies |
| Volume | 10 | Issue | 12 | Pages | 2136-29 |
| Keywords | A1 Journal article; Economics; Engineering sciences. Technology; Engineering Management (ENM) | ||||
| Abstract | Air pollutants from fossil fuel fired power plants harm the environment and human health. More than 91% of Irans electricity production is from thermal power plants that use natural gas, diesel, and fuel oil. We apply the impact pathway approach to estimate the health impacts arising from Iranian fossil-based electricity generation emission, and in a next step, we calculate monetary costs of the estimated damages, for a one-year period starting from 20 March 2016 through 2017. We use the new version of SIMPACTS (International Atomic Energy Agency, Vienna, Austria) to investigate the health effects from 61 major Iran fossil-based power plants separately. The selected plants represent 95.6% of total Iran fossil-based power generation. Using the individual and different power plant estimates, we avoid extrapolation and our results can be considered more reliable, taking into account spatial differences. The total damage cost is 723.42 million USD (2000). The damage cost per generated electricity varies from 0.06 to 22.41 USD/MWh and average plant damage cost is 2.85 USD/MWh. Accounting for these external costs indicates the actual costs of fossil energy. The results are useful for policy makers to compare the health costs from these plants and to decide on cleaner energy sources and to take measures to increase benefits for society. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000423156900207 | Publication Date | 2017-12-15 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1996-1073 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 2.262 | Times cited | 4 | Open Access | |
| Notes | ; ; | Approved | Most recent IF: 2.262 | ||
| Call Number | UA @ admin @ c:irua:149041 | Serial | 6200 | ||
| Permanent link to this record | |||||
| Author |
Joolaie, R.; Sarvestani, A.A.; Taheri, F.; Van Passel, S.; Azadi, H. | ||||
| Title | Sustainable cropping pattern in North Iran : application of fuzzy goal programming | Type | A1 Journal article | ||
| Year | 2017 | Publication | Environment, development and sustainability | Abbreviated Journal | |
| Volume | 19 | Issue | 6 | Pages | 2199-2216 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM) | ||||
| Abstract | Due to the important role that the application of mathematical programming models have in determining optimal cropping patterns, this research presents a sustainable cropping pattern that considers selected economic, environmental, and social goals together. Using a random sampling method, a sample size of 168 farmers was selected in the Sari County, Iran. Our results showed that economic, self-sufficiency, environmental, and social goals have a distinctly different impact on cropping pattern performance. Compared to the current cropping pattern, the gross margins for economic and social goals increased by nearly 11 and 2 %, respectively, and the gross margins for self-sufficiency and environmental goals decreased by nearly 2 and 36 %. Interestingly, it has been found that the performance of the current cropping pattern has an average positive impact of 6 % if economic, self-sufficiency, environmental, and social (employment) goals are realized simultaneously. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000414459300004 | Publication Date | 2016-09-02 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1387-585x | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles; WoS full record; WoS citing articles | |
| Impact Factor | Times cited | 2 | Open Access | ||
| Notes | ; ; | Approved | Most recent IF: NA | ||
| Call Number | UA @ admin @ c:irua:147370 | Serial | 6257 | ||
| Permanent link to this record | |||||
| Author |
Jiang, Y.; Mao, J.; Moldovan, D.; Masir, M.R.; Li, G.; Watanabe, K.; Taniguchi, T.; Peeters, F.M.; Andrei, E.Y. | ||||
| Title | Tuning a circular p-n junction in graphene from quantum confinement to optical guiding | Type | A1 Journal article | ||
| Year | 2017 | Publication | Nature nanotechnology | Abbreviated Journal | Nat Nanotechnol |
| Volume | 12 | Issue | 11 | Pages | 1045-+ |
| Keywords | A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT) | ||||
| Abstract | <script type='text/javascript'>document.write(unpmarked('The photon-like propagation of the Dirac electrons in graphene, together with its record-high electronic mobility(1-3), can lead to applications based on ultrafast electronic response and low dissipation(4-6). However, the chiral nature of the charge carriers that is responsible for the high mobility also makes it difficult to control their motion and prevents electronic switching. Here, we show how to manipulate the charge carriers by using a circular p-n junction whose size can be continuously tuned from the nanometre to the micrometre scale(7,8). The junction size is controlled with a dual-gate device consisting of a planar back gate and a point-like top gate made by decorating a scanning tunnelling microscope tip with a gold nanowire. The nanometre-scale junction is defined by a deep potential well created by the tip-induced charge. It traps the Dirac electrons in quantum-confined states, which are the graphene equivalent of the atomic collapse states (ACSs) predicted to occur at supercritically charged nuclei(9-13). As the junction size increases, the transition to the optical regime is signalled by the emergence of whispering-gallery modes(14-16), similar to those observed at the perimeter of acoustic or optical resonators, and by the appearance of a Fabry-Perot interference pattern(17-20) for junctions close to a boundary.')); | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000414531800011 | Publication Date | 2017-09-15 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1748-3387; 1748-3395 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 38.986 | Times cited | 65 | Open Access | |
| Notes | ; The authors acknowledge funding provided by DOE-FG02-99ER45742 (STM/STS) and NSF DMR 1708158 (fabrication). Theoretical work was supported by ESF-EUROCORES-EuroGRAPHENE, FWO VI and the Methusalem program of the Flemish government. ; | Approved | Most recent IF: 38.986 | ||
| Call Number | UA @ lucian @ c:irua:147406 | Serial | 4902 | ||
| Permanent link to this record | |||||
| Author |
Jany, B.R.; Gauquelin, N.; Willhammar, T.; Nikiel, M.; van den Bos, K.H.W.; Janas, A.; Szajna, K.; Verbeeck, J.; Van Aert, S.; Van Tendeloo, G.; Krok, F. | ||||
| Title | Controlled growth of hexagonal gold nanostructures during thermally induced self-assembling on Ge(001) surface | Type | A1 Journal article | ||
| Year | 2017 | Publication | Scientific reports | Abbreviated Journal | Sci Rep-Uk |
| Volume | 7 | Issue | 7 | Pages | 42420 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Nano-sized gold has become an important material in various fields of science and technology, where control over the size and crystallography is desired to tailor the functionality. Gold crystallizes in the face-centered cubic (fcc) phase, and its hexagonal closed packed (hcp) structure is a very unusual and rare phase. Stable Au hcp phase has been reported to form in nanoparticles at the tips of some Ge nanowires. It has also recently been synthesized in the form of thin graphene-supported sheets which are unstable under electron beam irradiation. Here, we show that stable hcp Au 3D nanostructures with well-defined crystallographic orientation and size can be systematically created in a process of thermally induced self-assembly of thin Au layer on Ge(001) monocrystal. The Au hcp crystallite is present in each Au nanostructure and has been characterized by different electron microscopy techniques. We report that a careful heat treatment above the eutectic melting temperature and a controlled cooling is required to form the hcp phase of Au on a Ge single crystal. This new method gives scientific prospects to obtain stable Au hcp phase for future applications in a rather simple manner as well as redefine the phase diagram of Gold with Germanium. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000393940700001 | Publication Date | 2017-02-14 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2045-2322 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 4.259 | Times cited | 25 | Open Access | OpenAccess |
| Notes | The authors gratefully acknowledge the financial support from the Polish National Science Center, grant no. DEC-2012/07/B/ST5/00906. N.G., G.V.T. and J.V. acknowledge the European Union (EU) Council under the 7th Framework Program (FP7) ERC Starting Grant 278510 VORTEX for support. The Research Foundation Flanders is acknowledged through project fundings (G.0374.13N, G.0368.15N, G.0369.15N) and for a Ph.D. research grant to K.H.W.v.d.B. The microscope was partly funded by the Hercules Fund from the Flemish Government. T.W. acknowledges the Swedish Research Council for an international postdoc grant. The research leading to these results has received funding from the European Union Seventh Framework Programme under Grant Agreement 312483–ESTEEM2 (Integrated Infrastructure Initiative–I3). Part of the research was carried out with equipment purchased with financial support from the European Regional Development Fund in the framework of the Polish Innovation Economy Operational Program (Contract No. POIG.02.01.00-12-023/08). | Approved | Most recent IF: 4.259 | ||
| Call Number | EMAT @ emat @ c:irua:140846UA @ admin @ c:irua:140846 | Serial | 4423 | ||
| Permanent link to this record | |||||
| Author |
Jacquet, Q.; Perez, A.; Batuk, D.; Van Tendeloo, G.; Rousse, G.; Tarascon, J.-M. | ||||
| Title | The Li3RuyNb1-yO4 (0 ≤y≤ 1) System: Structural Diversity and Li Insertion and Extraction Capabilities | Type | A1 Journal article | ||
| Year | 2017 | Publication | Chemistry of materials | Abbreviated Journal | Chem Mater |
| Volume | 29 | Issue | 12 | Pages | 5331-5343 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Searching for novel high-capacity electrode materials combining cationic and anionic redox processes is an ever-growing activity within the field of Li-ion batteries. In this respect, we report on the exploration of the Li3RuyNb1-yO4 (O <= y <= 1) system with an O/M ratio of 4 to maximize the number of oxygen lone pairs, responsible for the anionic redox. We show that this system presents a very rich crystal chemistry with the existence of four structural types, which derive from the rocksalt structure but differ in their cationic arrangement, creating either zigzag, helical, jagged chains or clusters. From an electrochemical standpoint, these compounds are active on reduction via a classical cationic insertion process. The oxidation process is more complex, because of the instability of the delithiated phase. Our results promote the use of the rich Li3MO4 family as a viable platform for a better understanding of the relationships between structure and anionic redox activity. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000404493100036 | Publication Date | 2017-06-27 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0897-4756 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 9.466 | Times cited | 17 | Open Access | Not_Open_Access |
| Notes | The authors thank Paul Pearce, Alexis Grimaud, Matthieu Saubanere, and Marie-Liesse Doublet for fruitful discussions, Vivian Nassif for her help in neutron diffraction experiment at the D1B diffractometer at ILL, and Dominique Foix for XPS analysis. Use of the Advanced Photon Source at Argonne National Laboratory was supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357. Q.J. thanks the ANR “Deli-Redox” for Ph.D. funding. J.-M.T. and D.B. acknowledge funding from the European Research Council (ERC) (FP/2014)/ERC Grant -Project 670116-ARPEMA. | Approved | Most recent IF: 9.466 | ||
| Call Number | EMAT @ emat @c:irua:147506 | Serial | 4776 | ||
| Permanent link to this record | |||||
| Author |
Ishikawa, K.; Karahashi, K.; Ichiki, T.; Chang, J.P.; George, S.M.; Kessels, W.M.M.; Lee, H.J.; Tinck, S.; Um, J.H.; Kinoshita, K. | ||||
| Title | Progress and prospects in nanoscale dry processes: How can we control atomic layer reactions? | Type | A1 Journal article | ||
| Year | 2017 | Publication | Japanese journal of applied physics | Abbreviated Journal | Jpn J Appl Phys |
| Volume | 56 | Issue | 56 | Pages | 06HA02 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | In this review, we discuss the progress of emerging dry processes for nanoscale fabrication. Experts in the fields of plasma processing have contributed to addressing the increasingly challenging demands in achieving atomic-level control of material selectivity and physicochemical reactions involving ion bombardment. The discussion encompasses major challenges shared across the plasma science and technology community. Focus is placed on advances in the development of fabrication technologies for emerging materials, especially metallic and intermetallic compounds and multiferroic, and two-dimensional (2D) materials, as well as state-of-the-art techniques used in nanoscale semiconductor manufacturing with a brief summary of future challenges. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000425887900001 | Publication Date | 2017-06-01 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0021-4922 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 1.384 | Times cited | 18 | Open Access | OpenAccess |
| Notes | The authors would like to thank Drs. Masanobu Honda, Miyako Matsui, Tomohiro Okumura, Tetsuya Tatsumi, Satoshi Hamaguchi, Hiroto Ohtake, Yoshinobu Ohya, Kazunori Shinoda, Masaru Izawa, Hisataka Hayashi, Toshio Hayashi, Makoto Sekine, and Masaru Hori, and all members of the Program and Publication Committee of the 38th International Symposium on Dry Process 2016 held in Sapporo, Japan, as well as Nicholas Altieri and Jeffrey Chang at UCLA for proofreading and providing feedback on the manuscript. | Approved | Most recent IF: 1.384 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:143872 | Serial | 4576 | ||
| Permanent link to this record | |||||