NANOlab Center of Excellence literature database -- Query Results

	NANOlab Center of Excellence literature database Home \| Show All \| Simple Search \| Advanced Search	Login Quick Search: Field: contains: ...
	271–300 of 336 records found matching your query (RSS \| history):

Select All Deselect All

<< 1 2 3 4 5 6 7 8 9 10 11 12 >>

List View

Citations

Details

	Records
	Author	Pourbabak, S.; Orekhov, A.; Samaee, V.; Verlinden, B.; Van Humbeeck, J.; Schryvers, D.
	Title	In-Situ TEM Stress Induced Martensitic Transformation in Ni50.8Ti49.2 Microwires			Type	A1 Journal article
	Year	2019	Publication	Shape memory and superelasticity	Abbreviated Journal	Shap. Mem. Superelasticity
	Volume	5	Issue	2	Pages	154-162
	Keywords	A1 Journal article; Electron microscopy for materials research (EMAT)
	Abstract	In-situ transmission electron microscopy tensile straining is used to study the stress induced martensitic transformation in Ni50.8Ti49.2. Two microwire samples with different heat treatment are investigated from which one single crystal and three polycrystalline TEM specimens, the latter with micro- and nano-size grains, have been produced. The measured Young’s modulus for all TEM specimens is around 70 GPa, considerably higher than the averaged 55 GPa of the original microwire sample. The height of the superelastic stress plateau shows an inverse relationship with the specimen thickness for the polycrystalline specimens. Martensite starts nucleating within the elastic region of the stress–strain curve and on the edges of the specimens while also grain boundaries act as nucleation sites in the polycrystalline specimens. When a martensite plate reaches a grain boundary in the polycrystalline specimen, it initiates the transformation in the neighboring grain at the other side of the grain boundary. In later stages martensite plates coalesce at higher loads in the stress plateau. In highly strained specimens, residual martensite remains after release.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000472940200002	Publication Date	2019-05-20
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	2199-384X	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor		Times cited		Open Access	Not_Open_Access
	Notes	Saeid Pourbabak likes to thank the Flemish Science Foundation FWO for financial support under Project G.0366.15N. This work was also made possible through the AUHA13009 Grant “TopSPIN for TEM nanostatistics” of the Flemish HERCULES foundation.			Approved	Most recent IF: NA
	Call Number	EMAT @ emat @UA @ admin @ c:irua:159989			Serial	5177
Permanent link to this record



	Author	Cautaerts, N.; Delville, R.; Stergar, E.; Pakarinen, J.; Verwerft, M.; Yang, Y.; Hofer, C.; Schnitzer, R.; Lamm, S.; Felfer, P.; Schryvers, D.
	Title	The role of Ti and TiC nanoprecipitates in radiation resistant austenitic steel: A nanoscale study			Type	A1 Journal article
	Year	2020	Publication	Acta Materialia	Abbreviated Journal	Acta Mater
	Volume	197	Issue		Pages	184-197
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	This work encompasses an in-depth transmission electron microscopy and atom probe tomography study of Ti-stabilized austenitic steel irradiated with Fe-ions. The focus is on radiation induced segregation and precipitation, and in particular on how Ti and TiC affect these processes. A 15-15Ti steel (grade: DIN 1.4970) in two thermo-mechanical states (cold-worked and aged) was irradiated at different temperatures up to a dose of 40 dpa. At low irradiation temperatures, the cold-worked and aged materials evolved to a similar microstructure dominated by small Si and Ni clusters, corresponding to segregation to small point defect clusters. TiC precipitates, initially present in the aged material, were found to be unstable under these irradiation conditions. Elevated irradiation temperatures resulted in the nucleation of nanometer sized Cr enriched TiC precipitates surrounded by Si and Ni enriched shells. In addition, nanometer sized Ti- and Mn-enriched G-phase (M6Ni16Si7) precipitates formed, often attached to TiC precipitates. Post irradiation, larger number densities of TiC were observed in the cold-worked material compared to the aged material. This was correlated with a lower volume fraction of G-phase. The findings suggest that at elevated irradiation temperatures, the precipitate-matrix interface is an important point defect sink and contributes to the improved radiation resistance of this material. The study is a first of its kind on stabilized steel and demonstrates the significance of the small Ti addition to the evolution of the microstructure under irradiation. (C) 2020 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000564767000001	Publication Date	2020-07-10
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1359-6454	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	9.4	Times cited		Open Access	Not_Open_Access
	Notes	; This work was supported by ENGIE [contract number 2015-AC-007 e BSUEZ6900]; the U.S. Department of Energy, Office of Nuclear Energy under DOE Idaho Operations Office Contract DE-AC07051D14517 as part of a Nuclear Science User Facilities experiment; and by the MYRRHA program at SCK-CEN, Belgium. Funding of the Austrian BMK (846933) in the framework of the program “Production of the future” and the “BMK Professorship for Industry” is gratefully acknowledged. We want to thank the staffat MIBL for assisting with the ion irradiations as well as the staffat CAES for assisting with FIB work and conducting APT measurements. ;			Approved	Most recent IF: 9.4; 2020 IF: 5.301
	Call Number	UA @ admin @ c:irua:171956			Serial	6626
Permanent link to this record



	Author	Ding, L.; Raskin, J.-P.; Lumbeeck, G.; Schryvers, D.; Idrissi, H.
	Title	TEM investigation of the role of the polycrystalline-silicon film/substrate interface in high quality radio frequency silicon substrates			Type	A1 Journal article
	Year	2020	Publication	Materials Characterization	Abbreviated Journal	Mater Charact
	Volume	161	Issue		Pages	110174-10
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	The microstructural characteristics of two polycrystalline silicon (poly-Si) films with different electrical properties produced by low-pressure chemical vapour deposition on top of high resistivity silicon substrates were investigated by advanced transmission electron microscopy (TEM), including high resolution aberration corrected TEM and automated crystallographic orientation mapping in TEM. The results reveal that the nature of the poly-Si film/Si substrate interface is the main factor controlling the electrical resistivity of the poly-Si films. The high resistivity and high electrical linearity of poly-Si films are strongly promoted by the Sigma 3 twin type character of the poly-Si/Si substrate interface, leading to the generation of a huge amount of extended defects including stacking faults, Sigma 3 twin boundaries as well as Sigma 9 grain boundaries at this interface. Furthermore, a high density of interfacial dislocations has been observed at numerous common and more exotic grain boundaries deviating from their standard crystallographic planes. In contrast, poly-Si film/Si substrate interfaces with random character do not favour the formation of such complex patterns of defects, leading to poor electrical resistivity of the poly-Si film. This finding opens windows for the development of high resistivity silicon substrates for Radio Frequency (RF) integrated circuits (ICs) applications.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000521515800027	Publication Date	2020-01-30
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1044-5803	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	4.7	Times cited		Open Access	Not_Open_Access
	Notes	; H. Idrissi is mandated by the Belgian National Fund for Scientific Research (FSR-FNRS). ;			Approved	Most recent IF: 4.7; 2020 IF: 2.714
	Call Number	UA @ admin @ c:irua:168664			Serial	6621
Permanent link to this record



	Author	Amin-Ahmadi, B.; Connétable, D.; Fivel, M.; Tanguy, D.; Delmelle, R.; Turner, S.; Malet, L.; Godet, S.; Pardoen, T.; Proost, J.; Schryvers, D.; Idrissi, H.
	Title	Dislocation/hydrogen interaction mechanisms in hydrided nanocrystalline palladium films			Type	A1 Journal article
	Year	2016	Publication	Acta materialia	Abbreviated Journal	Acta Mater
	Volume	111	Issue	111	Pages	253-261
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	The nanoscale plasticity mechanisms activated during hydriding cycles in sputtered nanocrystalline Pd films have been investigated ex-situ using advanced transmission electron microscopy techniques. The internal stress developing within the films during hydriding has been monitored in-situ. Results showed that in Pd films hydrided to β-phase, local plasticity was mainly controlled by dislocation activity in spite of the small grain size. Changes of the grain size distribution and the crystallographic texture have not been observed. In contrast, significant microstructural changes were not observed in Pd films hydrided to α-phase. Moreover, the effect of hydrogen loading on the nature and density of dislocations has been investigated using aberration-corrected TEM. Surprisingly, a high density of shear type stacking faults has been observed after dehydriding, indicating a significant effect of hydrogen on the nucleation energy barriers of Shockley partial dislocations. Ab-initio calculations of the effect of hydrogen on the intrinsic stable and unstable stacking fault energies of palladium confirm the experimental observations.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000375812100027	Publication Date	2016-04-06
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1359-6454	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	5.301	Times cited	14	Open Access
	Notes	This work was carried out in the framework of the IAP program of the Belgian State Federal Office for Scientific, Technical and Cultural Affairs, under Contract No. P7/21. The support of the FWO research project G012012N “Understanding nanocrystalline mechanical behaviour from structural investigations” for B. Amin-Ahmadi is also gratefully acknowledged. This work was granted access to the HPC resources of CALMIP (CICT Toulouse, France) under the allocations 2014-p0912 and 2014-p0749.			Approved	Most recent IF: 5.301
	Call Number	c:irua:132678			Serial	4054
Permanent link to this record



	Author	van der Rest, A.; Idrissi, H.; Henry, F.; Favache, A.; Schryvers, D.; Proost, J.; Raskin, J.-P.; Van Overmeere, Q.; Pardoen, T.
	Title	Mechanical behavior of ultrathin sputter deposited porous amorphous Al2O3 films			Type	A1 Journal article
	Year	2017	Publication	Acta materialia	Abbreviated Journal	Acta Mater
	Volume	125	Issue	125	Pages	27-37
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	The determination of the mechanical properties of porous amorphous Al2O3 thin films is essential to address reliability issues in wear-resistant, optical and electronic coating applications. Testing the mechanical properties of Al2O3 films thinner than 200 nm is challenging, and the link between the mechanical behavior and the microstructure of such films is largely unknown. Herein, we report on the elastic and viscoplastic mechanical properties of amorphous Al2O3 thin films synthesized by reactive magnetron sputtering using a combination of internal stress, nanoindentation, and on-chip uniaxial tensile testing, together with mechanical homogenization models to separate the effect of porosity from intrinsic variations of the response of the sound material. The porosity is made of voids with 2e30 nm diameter. The Young's modulus and hardness of the films decrease by a factor of two when the deposition pressure increases from 1.2 to 8 mTorr. The contribution of porosity was found to be small, and a change in the atomic structure of the amorphous Al2O3 matrix is hypothesized to be the main contributing factor. The activation volume associated to the viscoplastic deformation mechanism is around 100 Å3. Differences in the atomic structure of the films could not be revealed by electron diffraction, pointing to a minute effect of atomic arrangement on the elastic properties.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000394201500003	Publication Date	2016-12-02
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1359-6454	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	5.301	Times cited	5	Open Access	OpenAccess
	Notes	This work has been funded by the Belgian Science Policy through the IAP 7/21 project. The support of the ‘Fonds Belge pour la Recherche dans l’Industrie et l’Agriculture (FRIA)’ for A.v.d.R. is also gratefully acknowledged, as well as the support of FNRS through the grant PDR T.0122.13 “Mecano”.			Approved	Most recent IF: 5.301
	Call Number	EMAT @ emat @ c:irua:138990			Serial	4330
Permanent link to this record



	Author	Ghidelli, M.; Idrissi, H.; Gravier, S.; Blandin, J.-J.; Raskin, J.-P.; Schryvers, D.; Pardoen, T.
	Title	Homogeneous flow and size dependent mechanical behavior in highly ductile Zr 65 Ni 35 metallic glass films			Type	A1 Journal article
	Year	2017	Publication	Acta materialia	Abbreviated Journal	Acta Mater
	Volume	131	Issue	131	Pages	246-259
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	Motivated by recent studies demonstrating a high strength – high ductility potential of nano-scale metallic glass samples, the mechanical response of freestanding Zr65Ni35 film with sub-micron thickness has been investigated by combining advanced on-chip tensile testing and electron microscopy. Large deformation up to 15% is found for specimen thicknesses below 500 nm with variations depending on specimen size and frame compliance. The deformation is homogenous until fracture, with no evidence of shear banding. The yield stress is doubled when decreasing the specimen cross-section, reaching ~3 GPa for small cross-sections. The fracture strain variation is related to both the stability of the test device and to the specimen size. The study concludes on clear disconnect between the mechanisms controlling the onset of plasticity and the fracture process.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000402343400023	Publication Date	2017-03-31
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1359-6454	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	5.301	Times cited	42	Open Access	OpenAccess
	Notes	This work has been funded by the Belgian Science Policy through the IAP 7/21 project. We acknowledge IDS-FunMat for the PhD financial support.We thank the Renatech network and the PTA (Plateforme Technologique Amont) in Grenoble (France) for TFMG deposition facilities. The WINFAB infrastructure at the UCL and the help of R. Vayrette and M. Coulombier for the on-chip tests. H. Idrissi is currently mandated by the Belgian National Fund for Scientific Research (FSR-FNRS).			Approved	Most recent IF: 5.301
	Call Number	EMAT @ emat @ c:irua:142642			Serial	4562
Permanent link to this record



	Author	Cautaerts, N.; Delville, R.; Stergar, E.; Schryvers, D.; Verwerft, M.
	Title	Characterization of (Ti,Mo,Cr)C nanoprecipitates in an austenitic stainless steel on the atomic scale			Type	A1 Journal article
	Year	2019	Publication	Acta materialia	Abbreviated Journal	Acta Mater
	Volume	164	Issue		Pages	90-98
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	Nanometer sized (Ti,Mo,Cr)C (MX-type) precipitates that grew in a 24% cold worked Ti-stabilized austenitic stainless steel (grade DIN 1.4970, member of the 15-15Ti austenitic stainless steels) after heat treatment were fully characterized with transmission electron microscopy (TEM), probe corrected high angle annular dark field scanning transmission electron microscopy (HR-HAADF STEM), and atom probe tomography (APT). The precipitates shared the cube-on-cube orientation with the matrix and were facetted on {111} planes, yielding octahedral and elongated octahedral shapes. The misfit dislocations were believed to have Burgers vectors a/6<112> which was verified by geometrical phase analysis (GPA) strain mapping of a matrix-precipitate interface. The dislocations were spaced five to seven atomic planes apart, on average slightly wider than expected for the lattice parameters of steel and TiC. Quantitative atom probe tomography analysis of the precipitates showed that precipitates were significantly enriched in Mo, Cr and V, and that they were hypostoichiometric with respect to C. These findings were consistent with a reduced lattice parameter. The precipitates were found primarily on Shockley partial dislocations originating from the original perfect dislocation network. These novel findings could contribute to the understanding of how TiC nanoprecipitates interact with point defects and matrix dislocations. This is essential for the application of these Ti-stabilized steels in high temperature environments or fast spectrum nuclear fission reactors.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000456902800008	Publication Date	2018-10-11
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1359-6454	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	5.301	Times cited	2	Open Access	Not_Open_Access: Available from 12.10.2020
	Notes	This work was supported by ENGIE [contract number 2015-AC- 007 e BSUEZ6900]; the U.S. Department of Energy, Office of Nuclear Energy under DOE Idaho Operations Office Contract DE-AC07- 051D14517 as part of a Nuclear Science User Facilities experiment; and by the MYRRHA program in development at SCKCEN, Belgium. Special thanks to Dr. H. Mezerji and Dr. T. Altantzis for the work on the FEI Titan microscope.We also want to thank Ms. J. Burns for the help on the FIB and Dr. Y. Wu at CAES for conducting the APT measurements.			Approved	Most recent IF: 5.301
	Call Number	EMAT @ emat @c:irua:154873UA @ admin @ c:irua:154873			Serial	5060
Permanent link to this record



	Author	Ghidelli, M.; Orekhov, A.; Bassi, A.L.; Terraneo, G.; Djemia, P.; Abadias, G.; Nord, M.; Béché, A.; Gauquelin, N.; Verbeeck, J.; Raskin, J.-p.; Schryvers, D.; Pardoen, T.; Idrissi, H.
	Title	Novel class of nanostructured metallic glass films with superior and tunable mechanical properties			Type	A1 Journal article
	Year	2021	Publication	Acta Materialia	Abbreviated Journal	Acta Mater
	Volume		Issue		Pages	116955
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	A novel class of nanostructured Zr50Cu50 (%at.) metallic glass films with superior and tunable mechanical properties is produced by pulsed laser deposition. The process can be controlled to synthetize a wide range of film microstructures including dense fully amorphous, amorphous embedded with nanocrystals and amorphous nano-granular. A unique dense self-assembled nano-laminated atomic arrangement characterized by alternating Cu-rich and Zr/O-rich nanolayers with different local chemical enrichment and amorphous or amorphous-crystalline composite nanostructure has been discovered, while significant in-plane clustering is reported for films synthetized at high deposition pressures. This unique nanoarchitecture is at the basis of superior mechanical properties including large hardness and elastic modulus up to 10 and 140 GPa, respectively and outstanding total elongation to failure (>9%), leading to excellent strength/ductility balance, which can be tuned by playing with the film architecture. These results pave the way to the synthesis of novel class of engineered nanostructured metallic glass films with high structural performances attractive for a number of applications in microelectronics and coating industry.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000670077800004	Publication Date	2021-05-12
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1359-6454	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	5.301	Times cited	27	Open Access	OpenAccess
	Notes	H.I. is mandated by the Belgian National Fund for Scientific Research (FSR-FNRS). This work was supported by the Fonds de la Recherche Scientifique – FNRS under Grant T.0178.19 and Grant CDR– J011320F. We acknowledge funding for the direct electron detector used in the 4D stem studies from the Hercules fund 'Direct electron detector for soft matter TEM' from the Flemish Government J.V acknowledges funding from the European Union's Horizon 2020 research and innovation program under grant agreement No 823717 – ESTEEM3. A.O. has received partial funding from the GOA project “Solarpaint” of the University of Antwerp. A.B. and J.V. acknowledge funding through FWO project G093417N ('Compressed sensing enabling low dose imaging in transmission electron microscopy') from the Flanders Research Fund. M.G. and A.L.B acknowledge Chantelle Ekanem for support in PLD depositions.			Approved	Most recent IF: 5.301
	Call Number	EMAT @ emat @c:irua:178142			Serial	6761
Permanent link to this record



	Author	Yang, M.; Orekhov, A.; Hu, Z.-Y.; Feng, M.; Jin, S.; Sha, G.; Li, K.; Samaee, V.; Song, M.; Du, Y.; Van Tendeloo, G.; Schryvers, D.
	Title	Shearing and rotation of β'' and β' precipitates in an Al-Mg-Si alloy under tensile deformation : in-situ and ex-situ studies			Type	A1 Journal article
	Year	2021	Publication	Acta Materialia	Abbreviated Journal	Acta Mater
	Volume	220	Issue		Pages	117310
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	The interaction between dislocations and nano-precipitates during deformation directly influences hardening response of precipitation-strengthening metals such as Al-Mg-Si alloys. However, how coherent and semi-coherent nano-precipitates accommodate external deformation applied to an Al alloy remains to be elucidated. In-situ tensile experiments in a transmission electron microscope (TEM) were conducted to study the dynamic process of dislocations cutting through coherent needle-like beta '' precipitates with diameters of 3 similar to 8 nm. Comprehensive investigations using in-situ, ex-situ TEM and atom probe tomography uncovered that beta '' precipitates were firstly sheared into small fragments, and then the rotation of the fragments, via sliding along precipitate/matrix interfaces, destroyed their initially coherent interface with the Al matrix. In contrast, semi-coherent beta' precipitates with sizes similar to beta '' were more difficult to be fragmented and accumulation of dislocations at the interface increased interface misfit between beta' and the Al matrix. Consequently, beta' precipitates could basically maintain their needle-like shape after the tensile deformation. This research gains new insights into the interaction between nano-precipitates and dislocations. (C) 2021 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000705535300005	Publication Date	2021-09-12
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1359-6454	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	5.301	Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: 5.301
	Call Number	UA @ admin @ c:irua:182528			Serial	6884
Permanent link to this record



	Author	Idrissi, H.; Béché, A.; Gauquelin, N.; Ul-Haq, I.; Bollinger, C.; Demouchy, S.; Verbeeck, J.; Pardoen, T.; Schryvers, D.; Cordier, P.
	Title	On the formation mechanisms of intragranular shear bands in olivine by stress-induced amorphization			Type	A1 Journal article
	Year	2022	Publication	Acta materialia	Abbreviated Journal	Acta Mater
	Volume	239	Issue		Pages	118247-118249
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	Intragranular amorphization shear lamellae are found in deformed olivine aggregates. The detailed trans-mission electron microscopy analysis of intragranular lamella arrested in the core of a grain provides novel information on the amorphization mechanism. The deformation field is complex and heteroge-neous, corresponding to a shear crack type instability involving mode I, II and III loading components. The formation and propagation of the amorphous lamella is accompanied by the formation of crystal defects ahead of the tip. These defects are geometrically necessary [001] dislocations, characteristics of high-stress deformation in olivine, and rotational nanodomains which are tentatively interpreted as disclinations. We show that these defects play an important role in dictating the path followed by the amorphous lamella. Stress-induced amorphization in olivine would thus result from a direct crystal-to -amorphous transformation associated with a shear instability and not from a mechanical destabilization due to the accumulation of high number of defects from an intense preliminary deformation. The pref-erential alignment of some lamellae along (010) is a proof of the lower ultimate mechanical strength of these planes.(c) 2022 The Authors. Published by Elsevier Ltd on behalf of Acta Materialia Inc. This is an open access article under the CC BY license ( http://creativecommons.org/licenses/by/4.0/ )
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000861076600004	Publication Date	2022-08-05
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1359-6454	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	9.4	Times cited	5	Open Access	OpenAccess
	Notes	The QuanTEM microscope was partially funded by the Flemish government. The K2 camera was funded by FWO Hercules fund G0H4316N 'Direct electron detector for soft matter TEM'. A. Beche acknowledges funding from FWO project G093417N ('Compressed sensing enabling low dose imaging in transmission electron microscopy'). H. Idrissi is mandated by the Belgian National Fund for Scientific Research (FSR-FNRS). This work was supported by the FNRS under Grant PDR – T011322F and by the European Research Council (ERC) under the European Union's Horizon 2020 research and innovation programme under grant agreement No 787,198 Time Man. J-L Rouviere is acknowledged for his support with the GPA softawre.			Approved	Most recent IF: 9.4
	Call Number	UA @ admin @ c:irua:191432			Serial	7186
Permanent link to this record



	Author	Gong, X.; Marmy, P.; Volodin, A.; Amin-Ahmadi, B.; Qin, L.; Schryvers, D.; Gavrilov, S.; Stergar, E.; Verlinden, B.; Wevers, M.; Seefeldt, M.
	Title	Multiscale investigation of quasi-brittle fracture characteristics in a 9Cr–1Mo ferritic–martensitic steel embrittled by liquid lead–bismuth under low cycle fatigue			Type	A1 Journal article
	Year	2016	Publication	Corrosion science	Abbreviated Journal
	Volume	102	Issue	102	Pages	137-152
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	Liquid metal embrittlement (LME) induced quasi-brittle fracture characteristics of a 9Cr–1Mo ferritic–martensitic steel (T91) after fatigue cracking in lead–bismuth eutectic (LBE) have been investigated at various length scales. The results show that the LME fracture morphology is primarily characterized by quasi-brittle translath flat regions partially covered by nanodimples, shallow secondary cracks propagating along the martensitic lath boundaries as well as tear ridges covered by micro dimples. These diverse LME fracture features likely indicate a LME mechanism involving multiple physical processes, such as weakening induced interatomic decohesion at the crack tip and plastic shearing induced nano/micro voiding in the plastic zone.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000367275700014	Publication Date	2015-10-22
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	0010938X	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor		Times cited	16	Open Access
	Notes	The work is financially supported by the MYRRHA project,SCK•CEN, Belgium and partly funded by the European AtomicEnergy Community’s (Euratom) Seventh Framework ProgrammeFP7/2007-2013 under grant agreement No. 604862 (MatISSEproject) and in the framework of the EERA (European EnergyResearch Alliance) Joint Programme on Nuclear Materials. Dr. TomVan der Donck (KU Leuven) is acknowledged for the EBSD mea-surements. The authors are grateful to Dr. Van Renterghem Wouter(SCK•CEN) for fruitful discussion of the TEM results. Xing Gongsincerely acknowledges valuable suggestions from Dr. S.P. Lynch(Defence Science and Technology Organisation and Monash Uni-versity, Melbourne, Australia).			Approved	Most recent IF: NA
	Call Number	c:irua:129997			Serial	4013
Permanent link to this record



	Author	Charalampopoulou, E.; Delville, R.; Verwerft, M.; Lambrinou, K.; Schryvers, D.
	Title	Transmission electron microscopy study of complex oxide scales on DIN 1.4970 steel exposed to liquid Pb-Bi eutectic			Type	A1 Journal article
	Year	2019	Publication	Corrosion science	Abbreviated Journal	Corrosion Science
	Volume	147	Issue		Pages	22-31
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	The deployment of Gen-IV lead-cooled fast reactors requires a good compatibility between the selected structural/cladding steels and the inherently corrosive heavy liquid metal coolant. An effective liquid metal corrosion mitigation strategy involves the in-situ steel passivation in contact with the oxygen-containing Pb-alloy coolant. Transmission electron microscopy was used in this work to study the multi-layered oxide scales forming on an austenitic stainless steel fuel cladding exposed to oxygen-containing (CO ≈ 10−6 mass%) static liquid leadbismuth eutectic (LBE) for 1000 h between 400 and 500 °C. The oxide scale constituents were analyzed, including the intertwined phases comprising the innermost biphasic layer.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000456902100003	Publication Date	2018-10-31
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	0010938X	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor		Times cited	5	Open Access	OpenAccess
	Notes	The authors would like to thank J. Joris for the technical support during corrosion testing and J. Lim for the manufacturing and calibration of the oxygen sensors and oxygen pumps used in this work. E. Charalampopoulou personally thanks H. Heidari, S. Pourbabak, A. Orekhov (EMAT) and N. Cautaerts (EMAT, SCK•CEN), for their valuable help with the training of the FEI Tecnai Osiris S/TEM and Jeol 3000 S/ TEM, respectively, as well as S. Van den Broeck (EMAT), J. Pakarinen (SCK•CEN) and W. Van Renterghem (SCK•CEN) for FIB sample preparation. Moreover, the authors gratefully acknowledge the funding provided in the framework of the ongoing development of the MYRRHA irradiation facility. The research leading to these results falls within the framework of the European Energy Research Alliance Joint Programme on Nuclear Materials (EERA JPNM).			Approved	Most recent IF: NA
	Call Number	EMAT @ emat @UA @ admin @ c:irua:157541			Serial	5164
Permanent link to this record



	Author	Pardoen, T.; Colla, M.-S.; Idrissi, H.; Amin-Ahmadi, B.; Wang, B.; Schryvers, D.; Bhaskar, U.K.; Raskin, J.-P.
	Title	A versatile lab-on-chip test platform to characterize elementary deformation mechanisms and electromechanical couplings in nanoscopic objects			Type	A1 Journal article
	Year	2016	Publication	Comptes rendus : physique	Abbreviated Journal	Cr Phys
	Volume	17	Issue	17	Pages	485-495
	Keywords	A1 Journal article; Electron microscopy for materials research (EMAT)
	Abstract	A nanomechanical on-chip test platform has recently been developed to deform under a variety of loading conditions freestanding thin films, ribbons and nanowires involving submicron dimensions. The lab-on-chip involves thousands of elementary test structures from which the elastic modulus, strength, strain hardening, fracture, creep properties can be extracted. The technique is amenable to in situ transmission electron microscopy (TEM) investigations to unravel the fundamental underlying deformation and fracture mechanisms that often lead to size-dependent effects in small-scale samples. The method allows addressing electrical and magnetic couplings as well in order to evaluate the impact of large mechanical stress levels on different solid-state physics phenomena. We had the chance to present this technique in details to Jacques Friedel in 2012 who, unsurprisingly, made a series of critical and very relevant suggestions. In the spirit of his legacy, the paper will address both mechanics of materials related phenomena and couplings with solids state physics issues.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000373524300020	Publication Date	2015-12-01
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1631-0705	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	2.048	Times cited	7	Open Access
	Notes	This research has been performed with the financial support of the “Politique scientifique fédérale” under the framework of the interuniversity attraction poles program, IAP7/21, as well as with the support of the “Communauté française de Belgique” under the program “Actions de recherche concertées” ARC 05/10-330 and ARC Convention No. 11/16-037. The support of the “Fonds belge pour la recherche dans l'industrie et l'agriculture (FRIA)” for M.-S. Colla is also gratefully acknowledged as are the FWO research projects G012012N “Understanding nanocrystalline mechanical behavior from structural investigations” for B. Amin-Ahmadi.			Approved	Most recent IF: 2.048
	Call Number	c:irua:129995			Serial	4014
Permanent link to this record



	Author	Sandfeld, S.; Samaee, V.; Idrissi, H.; Groten, J.; Pardoen, T.; Schwaiger, R.; Schryvers, D.
	Title	Datasets for the analysis of dislocations at grain boundaries and during vein formation in cyclically deformed Ni micropillars			Type	A1 Journal article
	Year	2019	Publication	Data in Brief	Abbreviated Journal
	Volume	27	Issue	27	Pages	104724
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	The dataset together with the corresponding Python scripts and Jupyter notebooks presented in this article are supplementary data for the work presented in Samaee et al., 2019 [1]. The data itself consists of two parts: the simulation data that was used in [1] to analyze the effect of a particular grain boundary on curved dislocations and the precession electron diffraction (PED) strain maps together with post-processed data for analyzing details of the observed dislocation vein structures. Additionally, the complete stress tensor components, which are not shown in [1], have also been included. The data sets are accompanied by Python code explaining the file formats and showing how to post-process the data. (c) 2019 The Author(s). Published by Elsevier Inc. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000501988200181	Publication Date	2019-11-03
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	2352-3409	ISBN		Additional Links	UA library record; WoS full record
	Impact Factor		Times cited		Open Access
	Notes				Approved	Most recent IF: NA
	Call Number	UA @ admin @ c:irua:165092			Serial	6292
Permanent link to this record



	Author	Delmelle, R.; Amin-Ahmadi, B.; Sinnaeve, M.; Idrissi, H.; Pardoen, T.; Schryvers, D.; Proost, J.
	Title	Effect of structural defects on the hydriding kinetics of nanocrystalline Pd thin films			Type	A1 Journal article
	Year	2015	Publication	International journal of hydrogen energy	Abbreviated Journal	Int J Hydrogen Energ
	Volume	40	Issue	40	Pages	7335-7347
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	While the microstructure of a metal is well-known to affect its equilibrium hydrogen uptake and therefore the hydriding thermodynamics, microstructural effects on the hydriding kinetics are much less documented. Moreover, for thin film systems, such microstructural effects are difficult to separate from the internal stress effect, since most defects generate internal stresses. Such a decoupling has been achieved in this paper for nanocrystalline Pd thin film model systems through the use of a high-resolution, in-situ curvature measurement set-up during Pd deposition, annealing and hydriding. This set-up allowed producing Pd thin films with similar internal stress levels but significantly different microstructures. This was evidenced from detailed defect statistics obtained by transmission electron microscopy, which showed that the densities of grain boundaries, dislocations and twin boundaries have all been lowered by annealing. The same set-up was then used to study the hydriding equilibrium and kinetic behaviour of the resulting films at room temperature. A full quantitative analysis of their hydriding cycles showed that the rate constants of both the adsorption- and absorption-limited kinetic regimes were strongly affected by microstructure. Defect engineering was thereby shown to increase the rate constants for hydrogen adsorption and absorption in Pd by a factor 40 and 30, respectively. Copyright (C) 2015, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication	Oxford	Editor
	Language		Wos	000355884300012	Publication Date	2015-05-02
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	0360-3199;	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	3.582	Times cited	13	Open Access
	Notes	Iap 7/21			Approved	Most recent IF: 3.582; 2015 IF: 3.313
	Call Number	c:irua:126429			Serial	838
Permanent link to this record



	Author	Akamine, H.; Van den Bos, K.H.W.; Gauquelin, N.; Farjami, S.; Van Aert, S.; Schryvers, D.; Nishida, M.
	Title	Determination of the atomic width of an APB in ordered CoPt using quantified HAADF-STEM			Type	A1 Journal article
	Year	2015	Publication	Journal of alloys and compounds	Abbreviated Journal	J Alloy Compd
	Volume	644	Issue	644	Pages	570-574
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	Anti-phase boundaries (APBs) in an ordered CoPt alloy are planar defects which disturb the ordered structure in their vicinity and decrease the magnetic properties. However, it has not yet been clarified to what extend the APBs disturb the ordering. In this study, high-resolution HAADF-STEM images are statistically analysed based on the image intensities estimated by the statistical parameter estimation theory. In the procedure, averaging intensities, fitting the intensity profiles to specific functions, and assessment based on a statistical test are performed. As a result, the APBs in the stable CoPt are found to be characterised by two atomic planes, and a contrast transition range as well as the centre of an inclined APB is determined. These results show that the APBs are quite sharp and therefore may have no notable effect on the net magnetic properties due to their small volume fraction. (C) 2015 Elsevier B.V. All rights reserved.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication	Amsterdam	Editor
	Language		Wos	000357143900083	Publication Date	2015-05-07
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	0925-8388;	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	3.133	Times cited	12	Open Access
	Notes	FWO G036815N; G036915N; G037413N; 278510 VORTEX; Hercules; ECASJO_;			Approved	Most recent IF: 3.133; 2015 IF: 2.999
	Call Number	c:irua:127008 c:irua:127008			Serial	675
Permanent link to this record



	Author	Ding, L.; Zhao, L.; Weng, Y.; Schryvers, D.; Liu, Q.; Idrissi, H.
	Title	Atomic-scale investigation of the heterogeneous precipitation in the E (Al₁₈Mg₃Cr₂) dispersoid of 7075 aluminum alloy			Type	A1 Journal article
	Year	2021	Publication	Journal Of Alloys And Compounds	Abbreviated Journal	J Alloy Compd
	Volume	851	Issue		Pages	156890
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	The heterogeneous precipitation of the eta (MgZn2) phase on the E (Al18Mg3Cr2) dispersoids of the 7075 aluminum alloy was systematically investigated by atomic resolution high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) and energy dispersive X-ray spectrometry (EDX). It is found that coarse B particles are heterogeneously precipitated at the E particle interface after water quenching and isothermal aging at 120 degrees C. The incoherent E/Al interface is responsible for the high tendency of heterogeneous precipitation of the B phase. Two different orientation relationships (ORs) between the eta, E and Al matrix are identified: OR1 [2 (11) over bar0](eta)[011](E)//[(1) over bar 12](Al), (01 (1) over bar0)(eta)//(13 (3) over bar)(E)//(201)(Al), OR2 [(1) over bar 12](E)//[0001](eta)//[011](Al), (01 (1) over bar0 )(eta)//(220)(E)//(34 (4) over bar)(Al). The eta phase is preferential to nucleate along the {111}(E) or the {220}(E) planes, depending on its OR. The heterogeneous nucleation of B phase on the E particle could stabilize the E/Al interface by introducing a coherent E/eta interface, which increases the drive force of heterogeneous precipitation. The reorientation of eta phase and mutual diffusion of solute atoms could assist the coherency of the E/eta interface. The present results suggest that increasing the coherency of the E/Al interface is a promising method to suppress the heterogeneous precipitation of the eta phase. (C) 2020 Elsevier B.V. All rights reserved.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000579868900103	Publication Date	2020-08-25
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	0925-8388	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	3.133	Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: 3.133
	Call Number	UA @ admin @ c:irua:173503			Serial	6717
Permanent link to this record



	Author	Safdel, A.; Zarei-Hanzaki, A.; Abedi, H.R.; Pourbabak, S.; Schryvers, D.; Basu, R.
	Title	Asymmetrical superelastic behavior of thermomechanically processed semi-equiatomic NiTi alloy in tensile and compressive modes of deformation			Type	A1 Journal article
	Year	2021	Publication	Journal Of Alloys And Compounds	Abbreviated Journal	J Alloy Compd
	Volume	878	Issue		Pages	160443
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	In the present work two different cold working and annealing schemes were utilized, and the asymmetric superelastic response of thermomechanically processed materials were then assessed through cyclic tensile and compressive modes of deformation. The values of transformation stress, transformation strain, and pseudoelastic strain were measured for each treated and solutionized specimens and the asymmetric response was compared. In the solution annealed state, the difference of these parameters at different deformation modes was negligible due to the weak texture of the material, while for thermomechanically treated ones, development of specific deformation and recrystallization texture components was identified to be one of the underlying reasons of intensified asymmetry. The evolved substructure during the thermomechanical processing also played a substantial role in determining the asymmetric response. The presence of fine grains and dense dislocation substructure could hinder the movement of the transformation front, thus limiting the range of transformation. In tensile mode, the transformation stress was lower, but higher transformation strain was achieved, which was discussed relying on the slip activity in specified oriented grains. The lower transformation strain in compression mode led to lower pseudoelastic strain due to the narrow transformation range which finally degraded superelastic response of the material. (C) 2021 Elsevier B.V. All rights reserved.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000660477400005	Publication Date	2021-05-18
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	0925-8388	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	3.133	Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: 3.133
	Call Number	UA @ admin @ c:irua:179564			Serial	6855
Permanent link to this record



	Author	Ding, L.; Zhao, M.; Ehlers, F.J.H.; Jia, Z.; Zhang, Z.; Weng, Y.; Schryvers, D.; Liu, Q.; Idrissi, H.
	Title	“Branched” structural transformation of the L12-Al3Zr phase manipulated by Cu substitution/segregation in the Al-Cu-Zr alloy system			Type	A1 Journal article
	Year	2024	Publication	Journal of materials science & technology	Abbreviated Journal	Journal of Materials Science & Technology
	Volume	185	Issue		Pages	186-206
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	The effect of Cu on the evolution of the Al3Zr phase in an Al-Cu-Zr cast alloy during solution treatment at 500 °C has been thoroughly studied by combining atomic resolution high-angle annular dark-field scanning transmission electron microscopy, energy-dispersive X-ray spectroscopy and first-principles cal- culations. The heat treatment initially produces a pure L12-Al3Zr microstructure, allowing for about 13 % Cu to be incorporated in the dispersoid. Cu incorporation increases the energy barrier for anti-phase boundary (APB) activation, thus stabilizing the L12 structure. Additional heating leads to a Cu-induced “branched”path for the L12 structural transformation, with the latter process accelerated once the first APB has been created. Cu atoms may either (i) be repelled by the APBs, promoting the transformation to a Cu-poor D023 phase, or (ii) they may segregate at one Al-Zr layer adjacent to the APB, promoting a transformation to a new thermodynamically favored phase, Al4CuZr, formed when these segregation layers are periodically arranged. Theoretical studies suggest that the branching of the L12 transformation path is linked to the speed at which an APB is created, with Cu attraction triggered by a comparatively slow process. This unexpected transformation behavior of the L12-Al3Zr phase opens a new path to understanding, and potentially regulating the Al3Zr dispersoid evolution for high temperature applications.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	001154261100001	Publication Date	2023-12-24
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1005-0302	ISBN		Additional Links	UA library record; WoS full record
	Impact Factor	10.9	Times cited		Open Access	Not_Open_Access
	Notes	This work was supported by the National Key Research and Development Program (No. 2020YFA0405900), the National Natural Science Foundation of China (Grant No. 52371111 and U2141215 ), the Natural Science Foundation of Jiangsu Province (No. BE2022159 ). We are grateful to the High Performance Computing Center of Nanjing Tech University for supporting the computational resources. H. Idrissi is mandated by the Belgian National Fund for Scientific Research (FSR- FNRS).			Approved	Most recent IF: 10.9; 2024 IF: 2.764
	Call Number	EMAT @ emat @c:irua:202392			Serial	8981
Permanent link to this record



	Author	Lambrinou, K.; Charalampopoulou, E.; Van der Donck, T.; Delville, R.; Schryvers, D.
	Title	Dissolution corrosion of 316L austenitic stainless steels in contact with static liquid lead-bismuth eutectic (LBE) at 500 °C			Type	A1 Journal article
	Year	2017	Publication	Journal of nuclear materials	Abbreviated Journal	J Nucl Mater
	Volume	490	Issue	490	Pages	9-27
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	This work addresses the dissolution corrosion behaviour of 316L austenitic stainless steels. For this purpose, solution-annealed and cold-deformed 316L steels were simultaneously exposed to oxygen-poor (<10-8 mass%) static liquid lead-bismuth eutectic (LBE) for 253e3282 h at 500 °C. Corrosion was consistently more severe for the cold-drawn steels than the solution-annealed steel, indicating the importance of the steel thermomechanical state. The thickness of the dissolution-affected zone was nonuniform, and sites of locally-enhanced dissolution were occasionally observed. The progress of LBE dissolution attack was promoted by the interplay of certain steel microstructural features (grain boundaries, deformation twin laths, precipitates) with the dissolution corrosion process. The identified dissolution mechanisms were selective leaching leading to steel ferritization, and non-selective leaching; the latter was mainly observed in the solution-annealed steel. The maximum corrosion rate decreased with exposure time and was found to be inversely proportional to the depth of dissolution attack.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000403132300002	Publication Date	2017-04-10
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	0022-3115	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	2.048	Times cited	24	Open Access	OpenAccess
	Notes	The authors would like to acknowledge the following 316L stainless steel suppliers: Industeel, ArcelorMittal Group, for the 316LSA plate procured and characterised in the FP6 EUROTRANSDEMETRA project (Contract no. FI6W-CT-2004-516520); OLARRA Aceros Inoxidables, Spain, for the 316LH1 rod; and SIDERO STAAL nv, Belgium, for the 316LH2 rod. K. Lambrinou would like to thank J. Joris for technical support during the launching and follow up of all corrosion tests, J. Lim for the manufacturing and calibration of the oxygen sensors used in these tests, T. Lapauw for the XRD measurements on the pristine steels, and S. Van den Broeck for the FIB sample preparation. Special thanks to S. Gavrilov for fruitful and intense discussions. The authors gratefully acknowledge the funding provided in the framework of the ongoing development of the MYRRHA irradiation facility. The research leading to these results falls within the framework of the European Energy Research Alliance Joint Programme on Nuclear Materials (EERA JPNM).			Approved	Most recent IF: 2.048
	Call Number	EMAT @ emat @ c:irua:142644			Serial	4563
Permanent link to this record



	Author	Penders, A.G.; Konstantinovic, M.J.; Yang, T.; Bosch, R.-w.; Schryvers, D.; Somville, F.
	Title	Microstructural investigation of IASCC crack tips extracted from thimble tube O-ring specimens			Type	A1 Journal article
	Year	2022	Publication	Journal of nuclear materials	Abbreviated Journal	J Nucl Mater
	Volume	565	Issue		Pages	153727-16
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	The microstructural features of intergranular irradiation-assisted stress corrosion crack tips from a redeemed neutron-irradiated flux thimble tube (60 dpa) have been investigated using focused-ion beam analysis and (scanning) transmission electron microscopy. The current work presents a close examination of the deformation field and oxide assembly associated with intergranular cracking, in addition to the analysis of radiation-induced segregation at leading grain boundaries. Evidence of stress induced martensitic transformation extending from the crack tips is presented. Intergranular crack arrest is demonstrated on the account of the external tensile stress orientation, and as a consequence of MnS inclusion particles segregating close to the fractured grain boundary. Exclusive observations of grain boundary oxidation prior to the cracking are presented, which is in full-agreement with the internal oxidation model.(c) 2022 Elsevier B.V. All rights reserved.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000799256300004	Publication Date	2022-04-11
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	0022-3115	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	3.1	Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: 3.1
	Call Number	UA @ admin @ c:irua:188609			Serial	7086
Permanent link to this record



	Author	Penders, A.G.; Konstantinović, M.J.; Van Renterghem, W.; Bosch, R.-W.; Schryvers, D.; Somville, F.
	Title	Characterization of IASCC crack tips extracted from neutron-irradiated flux thimble tube specimens in view of a probabilistic fracture model			Type	A1 Journal article
	Year	2022	Publication	Journal of nuclear materials	Abbreviated Journal	J Nucl Mater
	Volume	571	Issue		Pages	154015-154016
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	This study reports the properties of irradiation assisted stress corrosion crack tips extracted by means of focused-ion beam from 60 to 80 dpa neutron-irradiated O-ring specimens tested under straining conditions under a pressurized-water reactor environment. Various crack tip morphologies and surrounding deformation features were analyzed as a function of applied stress, surface oxidation state and loading form – constant versus cyclic. All investigated cracks exhibit grain boundary oxidation in front of the crack tip, with the extent of oxidation being proportional to applied stress. These findings clearly demonstrate that, under the subcritical crack propagation regime, the grain boundary oxide grows faster than the crack. On the other hand, crack tips appertaining to specimens with removed oxide layer at the outer surface show comparatively less oxidation at the crack tip, which could indicate towards crack initiation from regions that exemplify lower stress, such as the O-ring inner surface. Cyclic loading is found to have a more pronounced effect on the crack tip microstructure, demonstrating increased deformation twinning and -martensitic transformation, which signifies towards an increased susceptibility to intergranular failure. Still, the extent of crack tip grain boundary oxidation in this case agrees well with expected values for maximum stress applied during cyclic loading. All results are interpreted based on the probabilistic subcritical crack propagation mechanism and provide strong support to a stress-driven internal oxidation model.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000872389200009	Publication Date	2022-09-06
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	0022-3115	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	3.1	Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: 3.1
	Call Number	UA @ admin @ c:irua:190375			Serial	7135
Permanent link to this record



	Author	Espinoza Torres, C.; Condó, A.M.; Haberkorn, N.; Zelaya, E.; Schryvers, D.; Guimpel, J.; Lovey, F.C.
	Title	Structures in textured Cu-Al-Ni shape memory thin films grown by sputtering			Type	A1 Journal article
	Year	2014	Publication	Materials characterization	Abbreviated Journal	Mater Charact
	Volume	96	Issue		Pages	256-262
	Keywords	A1 Journal article; Electron microscopy for materials research (EMAT)
	Abstract	The structure and texture formation in CuAlNi thin films of different thicknesses (1 μm to 5 μm) grown by DC magnetron sputtering without any intentional heating of the substrate are reported. The as-grown films present grains with an average size of 20 nm. The films with thickness of 1 μm have a single metastable phase with a hexagonal structure and are textured with planes (0002) parallel to the plane of the films. It was observed that thicker films present phase coexistence between metastable hexagonal and body centered cubic structures with a gradual increment of the body centered cubic phase fraction. The films with thickness of 5 μm are textured with planes (0002) and View the MathML source101¯0 in the hexagonal structure, whereas in the body centered cubic structure the films are textured with {110} planes parallel to the plane of the films. This fact can be associated with self-heating of the substrate during the growth of the films and with the relative stability of the metastable phases. Free standing films annealed in a second step (1123 K for 1 h) present austenitic phase with L21 structure and sub-micrometric grains textured with {220}L21 planes parallel to the plane of the films. The martensitic transformation temperature was determined from the analysis of resistance against temperature measurements.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication	New York	Editor
	Language		Wos	000343346400032	Publication Date	2014-08-10
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1044-5803;	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	2.714	Times cited	9	Open Access
	Notes	(CONICET PIP 11220090100457) and MINCYT-FWO International Exchange Project FW/09/03 is also acknowledged			Approved	Most recent IF: 2.714; 2014 IF: 1.845
	Call Number	UA @ lucian @ c:irua:118931			Serial	3321
Permanent link to this record



	Author	Tang, Y.; Chen, Z.; Borbely, A.; Ji, G.; Zhong, S.Y.; Schryvers, D.; Ji, V.; Wang, H.W.
	Title	Quantitative study of particle size distribution in an in-situ grown Al-TiB2 composite by synchrotron X-ray diffraction and electron microscopy			Type	A1 Journal article
	Year	2015	Publication	Materials characterization	Abbreviated Journal	Mater Charact
	Volume	102	Issue	102	Pages	131-136
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	Synchrotron X-ray diffraction and transmission electron microscopy (TEM) were applied to quantitatively characterize the average particle size and size distribution of free-standing TiB2 particles and TiB2 particles in an insitu grown Al–TiB2 composite. The detailed evaluations were carried out by X-ray line profile analysis using the restrictedmoment method and multiplewhole profile fitting procedure (MWP). Both numericalmethods indicate that the formed TiB2 particles are well crystallized and free of crystal defects. The average particle size determined from different Bragg reflections by the restricted moment method ranges between 25 and 55 nm, where the smallest particle size is determined using the 110 reflection suggesting the highest lateral-growth velocity of (110) facets. TheMWP method has shown that the in-situ grown TiB2 particles have a very low dislocation density (~1011 m−2) and their size distribution can be described by a log-normal distribution. Good agreement was found between the results obtained from the restricted moment and MWP methods, which was further confirmed by TEM.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication	New York	Editor
	Language		Wos	000355335200017	Publication Date	2015-03-04
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1044-5803;	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	2.714	Times cited	41	Open Access
	Notes	This work is financially supported by the National Natural Science Foundation of China (Grant No. 51201099 and No. 51301108) and the China Postdoctoral Science Foundation (Grant No. 2013T60443 and No. 2012M520891). The authors are grateful for the project 2013BB03 supported by NPL, CAEP. Many thanks are also due to the faculty of BL14B beamline at the Shanghai Synchrotron Radiation Facility for their help on synchrotron experiments.			Approved	Most recent IF: 2.714; 2015 IF: 1.845
	Call Number	c:irua:126443			Serial	2764
Permanent link to this record



	Author	Ji, G.; Tan, Z.; Lu, Y.; Schryvers, D.; Li, Z.; Zhang, D.
	Title	Heterogeneous interfacial chemical nature and bonds in a W-coated diamond/Al composite			Type	A1 Journal article
	Year	2016	Publication	Materials characterization	Abbreviated Journal	Mater Charact
	Volume	112	Issue	112	Pages	129-133
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	Heterogeneous Al/Al4C3/Al2O3/diamond{111}, Al/nanolayered Al4C3/diamond{111} and Al12W particle/Al4C3/Al2O3/diamond{111} multi-interfaces have been developed at the nanoscale in a W-coated diamond/Al composite produced by vacuum hot pressing. The formation of nanoscale Al4C3 crystals is strongly associated with local O enrichment and can be further promoted by Al12W interfacial particles. The latter effectively contributes to enhance interfacial chemical bonding reducing interfacial thermal resistance and, in turn, enhancing thermal conductivity.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000370109200015	Publication Date	2015-12-18
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1044-5803	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	2.714	Times cited	7	Open Access
	Notes	This work is financially supported by the FWO project of Belgium (No. U2 FA 070100/3506), the travel funding BQR (No. R8DIV AUE) provided by Université Lille 1, the National Natural Science Foundation of China (Grant No. 51401123) and the China Postdoctoral Science Foundation (Grant No. 2014 M561469) for Dr. Z.Q. Tan. Dr. W.G. Grünewald (LeicaMicrosystems, Germany) is also thanked for the assistance of surface preparation.			Approved	Most recent IF: 2.714
	Call Number	c:irua:129976			Serial	3987
Permanent link to this record



	Author	Yan, L.; Tan, Z.; Ji, G.; Li, Z.; Fan, G.; Schryvers, D.; Shan, A.; Zhang, D.
	Title	A quantitative method to characterize the Al4C3-formed interfacial reaction: the case study of MWCNT/Al composites			Type	A1 Journal article
	Year	2015	Publication	Materials characterization	Abbreviated Journal	Mater Charact
	Volume	112	Issue	112	Pages	213-218
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	The Al4C3-formed interfacial reaction plays an important role in tuning the mechanical and thermal properties of carbon/aluminum (C/Al) composites reinforced with carbonaceous materials such as multi-wall carbon nanotube (MWCNT) and graphene nanosheet. In terms of the hydrolysis nature of Al4C3, an electrochemical dissolution method was developed to quantitatively characterize the extent of C/Al interfacial reaction, which involves dissolving the composite samples in alkaline solution first, then collecting and measuring the CH4 gas released by Al4C3 hydrolysis with a gas chromatograph. Through a case study with powder metallurgy fabricated 2.0 wt.% MWCNT/Al composites, the detectability limit of the proposed method is 0.4 wt.% Al4C3, corresponding to 5 % extent of interfacial reaction with a measurement error of ±3 %. And then, with the already known MWCNT/Al reaction extent vs different sintering temperature and time, the reaction kinetics with an activation energy of 281 kJ mol-1 was successfully derived. Therefore, this rapid, sensitive, accurate method supplies an useful tool to optimize the processing and properties of all kinds of C/Al composites via interface design/control.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000370109200026	Publication Date	2015-12-29
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1044-5803	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	2.714	Times cited	24	Open Access
	Notes	The authors would like to acknowledge the financial support of the National Basic Research Program of China (973 Program, No. 2012CB619600), the National High-Tech R&D Program (863 Program, No. 2012AA030611), the National Natural Science Foundation (Nos. 51071100, 51131004, 51401123, 51511130038) and the research grant (Nos. 14DZ2261200, 15JC1402100, 14520710100) from Shanghai government. Dr. Z.Q. Tan would also like to thank the project funded by the China Postdoctoral Science Foundation (No. 2014M561469). The research leading to these results has partially received funding from the European Union Seventh Framework Program under Grant Agreement 312483 – ESTEEM2 (Integrated Infrastructure Initiative – I3).; esteem2_jra2			Approved	Most recent IF: 2.714; 2015 IF: 1.845
	Call Number	c:irua:130066 c:irua:130066			Serial	3997
Permanent link to this record



	Author	Lu, J.B.; Schryvers, D.
	Title	Microstructure and phase composition characterization in a Co38Ni33Al29 ferromagnetic shape memory alloy			Type	A1 Journal article
	Year	2016	Publication	Materials characterization	Abbreviated Journal	Mater Charact
	Volume	118	Issue	118	Pages	9-13
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	Transmission electron microscopy was performed to investigate the microstructures of a secondary phase and its surrounding matrix in a Co38Ni33Al29 ferromagnetic shape memory alloy. The secondary phase shows a γ′ L12 structure exhibiting a dendritic morphology with enclosed B2 austenite regions while the matrix shows the L10 martensitic structure. A secondary phase-austenite-martensite sandwich structure with residual austenite ranging from several hundred nanometers to several micrometers wide is observed at the secondary phase-martensite interface due to the depletion of Co and enrichment of Al in the chemical gradient zone and the effect of the strong martensitic start temperature dependency of the element concentrations. The crystallographic orientation relationship of the secondary phase and the B2 austenite fits the Kurdjumov-Sachs relationship.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000383292000002	Publication Date	2016-05-04
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1044-5803	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	2.714	Times cited	3	Open Access
	Notes	J.B. Lu thanks the Belgian Science Ministry (Belspo) for support of his post-doctoral research stay at EMAT. We thank S. Sedlakova-Ignacova from the Institute of Physics in Prague, Czech Republic, for providing samples.			Approved	Most recent IF: 2.714
	Call Number	c:irua:133100			Serial	4071
Permanent link to this record



	Author	Li, K.; Idrissi, H.; Sha, G.; Song, M.; Lu, J.; Shi, H.; Wang, W.; Ringer, S.P.; Du, Y.; Schryvers, D.
	Title	Quantitative measurement for the microstructural parameters of nano-precipitates in Al-Mg-Si-Cu alloys			Type	A1 Journal article
	Year	2016	Publication	Materials characterization	Abbreviated Journal	Mater Charact
	Volume	118	Issue	118	Pages	352-362
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	Size, number density and volume fraction of nano-precipitates are important microstructural parameters controlling the strengthening of materials. In this work a widely accessible, convenient, moderately time efficient method with acceptable accuracy and precision has been provided for measurement of volume fraction of nano-precipitates in crystalline materials. The method is based on the traditional but highly accurate technique of measuring foil thickness via convergent beam electron diffraction. A new equation is proposed and verified with the aid of 3-dimensional atom probe (3DAP) analysis, to compensate for the additional error resulted from the hardly distinguishable contrast of too short incomplete precipitates cut by the foil surface. The method can be performed on a regular foil specimen with a modem LaB6 or field-emission-gun transmission electron microscope. Precisions around +/- 16% have been obtained for precipitate volume fractions of needle-like beta ''/C and Q precipitates in an aged Al-Mg-Si-Cu alloy. The measured number density is dose to that directly obtained using 3DAP analysis by a misfit of 45%, and the estimated precision for number density measurement is about +/- 11%. The limitations of the method are also discussed.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000383292000042	Publication Date	2016-06-07
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1044-5803	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	2.714	Times cited	9	Open Access
	Notes	This work is financially supported by National Natural Science Foundation of China (51501230 and 51531009) and Postdoctoral Science Foundation of Central South University (502042057). H.I. acknowledges the IAP program of the Belgian State Federal Office for Scientific, Technical and Cultural Affairs under Contract No. P7/21 and FWO project G.0576.09N.			Approved	Most recent IF: 2.714
	Call Number	EMAT @ emat @ c:irua:137171			Serial	4334
Permanent link to this record



	Author	Pourbabak, S.; Montero-Sistiaga, M.L.; Schryvers, D.; Van Humbeeck, J.; Vanmeensel, K.
	Title	Microscopic investigation of as built and hot isostatic pressed Hastelloy X processed by Selective Laser Melting			Type	A1 Journal article
	Year	2019	Publication	Materials characterization	Abbreviated Journal	Mater Charact
	Volume	153	Issue		Pages	366-371
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	Microstructural characteristics of Hastelloy X produced by Selective Laser Melting have been investigated by various microscopic techniques in the as built (AB) condition and after hot isostatic pressing (HIP). At sub-grain level the AB material consists of columnar high density dislocation cells while the HIP sample consists of columnar sub-grains with lower dislocation density that originate from the original dislocation cells, contradicting existing models. The sub-grains contain nanoscale precipitates enriched in Al, Ti, Cr and O, located at sub-grain boundaries in the AB condition and within the grains after HIP. At some grain boundaries, micrometer sized chromium carbides are detected after HIP. Micro hardness within the grains was found to decrease after HIP, which was attributed to the decrease in dislocation density due to recovery annealing.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000472696900040	Publication Date	2019-05-21
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1044-5803	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	2.714	Times cited	2	Open Access	Not_Open_Access
	Notes	S.P. likes to thank the Flemish Science Foundation FWO for financial support under Project G.0366.15N. The authors acknowledge ENGIE Research and Technology Division for the use of the SLM280HL machine and financial support. This work was also made possible through the AUHA13009 grant “TopSPIN for TEM nanostatistics” of the Flemish HERCULES foundation.			Approved	Most recent IF: 2.714
	Call Number	EMAT @ emat @UA @ admin @ c:irua:159974			Serial	5178
Permanent link to this record



	Author	Cao, S.; Zeng, C.Y.; Li, Y.Y.; Yao, X.; Ma, X.; Samaee, V.; Schryvers, D.; Zhang, X.P.
	Title	Quantitative FIB/SEM three-dimensional characterization of a unique Ni₄Ti₃ network in a porous Ni50.8Ti49.2 alloy undergoing a two-step martensitic transformation			Type	A1 Journal article
	Year	2020	Publication	Materials Characterization	Abbreviated Journal	Mater Charact
	Volume	169	Issue		Pages	110595
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	The three-dimensional (3D) nanostructure of Ni4Ti3 precipitates in a porous Ni50.8Ti49.2 alloy has been re-constructed by “Slice-and-View” in a Focused Ion Beam/Scanning Electron Microscope (FIB/SEM). The 3D configuration of these precipitates forming a network structure in the B2 austenite matrix has been characterized via 3D visualization and quantitative analysis including volume fraction, skeleton, degree of anisotropy and local thickness. It is found that dense Ni4Ti3 precipitates occupy 54% of the volume in the B2 austenite matrix. Parallel Ni4Ti3 precipitates grow alongside the surface of a micro-pore, yielding an asymmetric structure, while nano voids do not seem to affect the growth of Ni4Ti3 precipitates. The small average local thickness of the precipitates around 60 nm allows their coherency with the matrix, and further induces the R-phase transformation in the matrix. On the other hand, the B2 matrix exhibits a winding and narrow structure with a skeleton of 18.20 mm and a thickness similar to the precipitates. This discontinuous matrix segmented by the Ni4Ti3 network and pores is responsible for the gradual transformation by stalling the martensite propagation.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000584353100001	Publication Date	2020-08-27
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1044-5803	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	4.7	Times cited		Open Access	OpenAccess
	Notes	; This work was supported by the National Natural Science Foundation of China under Grant Nos. 51401081 and 51571092, the Natural Science Foundation of Guangdong Province through Key Project under Grant No. 2018B0303110012 and General Project under Grant No. 2017A030313323, and China Scholarship Council (CSC). ;			Approved	Most recent IF: 4.7; 2020 IF: 2.714
	Call Number	UA @ admin @ c:irua:173547			Serial	6590
Permanent link to this record