Home | << 1 2 >> |
![]() |
Records | |||||
---|---|---|---|---|---|
Author | Kolev, S.; Bogaerts, A. | ||||
Title ![]() |
A 2D model for a gliding arc discharge | Type | A1 Journal article | ||
Year | 2015 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 24 | Issue | 24 | Pages | 015025 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | In this study we report on a 2D fluid model of a gliding arc discharge in argon. Despite the 3D nature of the discharge, 2D models are found to be capable of providing very useful information about the operation of the discharge. We employ two modelsan axisymmetric and a Cartesian one. We show that for the considered experiment and the conditions of a low current arc (around 30 mA) in argon, there is no significant heating of the cathode surface and the discharge is sustained by field electron emission from the cathode accompanied by the formation of a cathode spot. The obtained discharge power and voltage are relatively sensitive to the surface properties and particularly to the surface roughness, causing effectively an amplification of the normal electric field. The arc body and anode region are not influenced by this and depend mainly on the current value. The gliding of the arc is modelled by means of a 2D Cartesian model. The arcelectrode contact points are analysed and the gliding mechanism along the electrode surface is discussed. Following experimental observations, the cathode spot is simulated as jumping from one point to another. A complete arc cycle is modelled from initial ignition to arc decay. The results show that there is no interaction between the successive gliding arcs. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Institute of Physics | Place of Publication | Bristol | Editor | |
Language | Wos | 000348298200026 | Publication Date | 2014-12-23 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252;1361-6595; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 34 | Open Access | |
Notes | Approved | Most recent IF: 3.302; 2015 IF: 3.591 | |||
Call Number | c:irua:122538 c:irua:122538 c:irua:122538 c:irua:122538 | Serial | 3 | ||
Permanent link to this record | |||||
Author | Trenchev, G.; Kolev, S.; Bogaerts, A. | ||||
Title ![]() |
A 3D model of a reverse vortex flow gliding arc reactor | Type | A1 Journal article | ||
Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 25 | Issue | 25 | Pages | 035014 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | In this computational study, a gliding arc plasma reactor with a reverse-vortex flow stabilization is modelled for the first time by a fluid plasma description. The plasma reactor operates with argon gas at atmospheric pressure. The gas flow is simulated using the k-ε Reynolds-averaged Navier–Stokes turbulent model. A quasi-neutral fluid plasma model is used for computing the plasma properties. The plasma arc movement in the reactor is observed, and the results for the gas flow, electrical characteristics, plasma density, electron temperature, and gas temperature are analyzed. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000376557400022 | Publication Date | 2016-04-09 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 20 | Open Access | |
Notes | This research was carried out in the framework of the network on Physical Chemistry of Plasma–Surface Interactions— Interuniversity Attraction Poles, phase VII (http://psi-iap7.ulb. ac.be/), and supported by the Belgian Science Policy Office (BELSPO), and it was also funded by the Fund for Scientific Research Flanders (FWO). Grant number: 11U5316N. | Approved | Most recent IF: 3.302 | ||
Call Number | c:irua:132888 c:irua:132888 | Serial | 4063 | ||
Permanent link to this record | |||||
Author | Belov, I.; Paulussen, S.; Bogaerts, A. | ||||
Title ![]() |
Appearance of a conductive carbonaceous coating in a CO2dielectric barrier discharge and its influence on the electrical properties and the conversion efficiency | Type | A1 Journal article | ||
Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 25 | Issue | 25 | Pages | 015023 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | This work examines the properties of a dielectric barrier discharge (DBD) reactor, built for CO2 decomposition, by means of electrical characterization, optical emission spectroscopy and gas chromatography. The discharge, formed in an electronegative gas (such as CO2, but also O2), exhibits clearly different electrical characteristics, depending on the surface conductivity of the reactor walls. An asymmetric current waveform is observed in the metaldielectric (MD) configuration, with sparse high-current pulses in the positive half-cycle (HC) and a more uniform regime in the negative HC. This indicates that the discharge is operating in two alternating regimes with rather different properties. At high CO2 conversion regimes, a conductive coating is deposited on the dielectric. This so-called coated MD configuration yields a symmetric current waveform, with current peaks in both the positive and negative HCs. In a double-dielectric (DD) configuration, the current waveform is also symmetric, but without current peaks in both the positive and negative HC. Finally, the DD configuration with conductive coating on the inner surface of the outer dielectric, i.e. so-called coated DD, yields again an asymmetric current waveform, with current peaks in the negative HC. These different electrical characteristics are related to the presence of the conductive coating on the dielectric wall of the reactor and can be explained by an increase of the local barrier capacitance available for charge transfer. The different discharge regimes affect the CO2 conversion, more specifically, the CO2 conversion is lowest in the clean DD configuration. It is somewhat higher in the coated DD configuration, and still higher in the MD configuration. The clean and coated MD configuration, however, gave similar CO2 conversion. These results indicate that the conductivity of the dielectric reactor walls can highly promote the development of the high-amplitude discharge current pulses and subsequently the CO2 conversion. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000370974800030 | Publication Date | 2016-01-21 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 25 | Open Access | |
Notes | The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7-PEOPLE-2013-ITN) under Grant Agreement № 606889 (RAPID—Reactive Atmospheric Plasma processIng—eDucation network). | Approved | Most recent IF: 3.302 | ||
Call Number | c:irua:130790 | Serial | 4006 | ||
Permanent link to this record | |||||
Author | Zhang, Q.-Z.; Bogaerts, A. | ||||
Title ![]() |
Capacitive electrical asymmetry effect in an inductively coupled plasma reactor | Type | A1 Journal Article | ||
Year | 2018 | Publication | Plasma Sources Science & Technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 27 | Issue | 10 | Pages | 105019 |
Keywords | A1 Journal Article; electrical asymmetry effect, inductively coupled plasma, self-bias, independent control of the ion fluxes and ion energy; Plasma, laser ablation and surface modeling Antwerp (PLASMANT) ; | ||||
Abstract | The electrical asymmetry effect is realized by applying multiple frequency power sources (13.56 MHz and 27.12 MHz) to a capacitively biased substrate electrode in a specific inductively coupled plasma reactor. On the one hand, by adjusting the phase angle θ between the multiple frequency power sources, an almost linear self-bias develops on the substrate electrode, and consequently the ion energy can be well modulated, while the ion flux stays constant within a large range of θ. On the other hand, the plasma density and ion flux can be significantly modulated by tuning the inductive power supply, while only inducing a small change in the self- bias. Independent control of self-bias/ion energy and ion flux can thus be realized in this specific inductively coupled plasma reactor. |
||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000448434100001 | Publication Date | 2018-10-26 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 1 | Open Access | Not_Open_Access |
Notes | We acknowledge financial support from the European Marie Skłodowska-Curie Individual Fellowship within H2020 (Grant Agreement 702604). This work was carried out in part using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen, a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the University of Antwerp. | Approved | Most recent IF: 3.302 | ||
Call Number | PLASMANT @ plasmant @c:irua:155506 | Serial | 5069 | ||
Permanent link to this record | |||||
Author | Bultinck, E.; Bogaerts, A. | ||||
Title ![]() |
Characterization of an Ar/O2 magnetron plasma by a multi-species Monte Carlo model | Type | A1 Journal article | ||
Year | 2011 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 20 | Issue | 4 | Pages | 045013-045013,12 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | A combined Monte Carlo (MC)/analytical surface model is developed to study the plasma processes occurring during the reactive sputter deposition of TiOx thin films. This model describes the important plasma species with a MC approach (i.e. electrons, Ar+ ions, {\rm O}_2 | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Institute of Physics | Place of Publication | Bristol | Editor | |
Language | Wos | 000295829800015 | Publication Date | 2011-06-14 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252;1361-6595; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 7 | Open Access | |
Notes | Approved | Most recent IF: 3.302; 2011 IF: 2.521 | |||
Call Number | UA @ lucian @ c:irua:89732 | Serial | 316 | ||
Permanent link to this record | |||||
Author | Sun, S.R.; Wang, H.X.; Bogaerts, A. | ||||
Title ![]() |
Chemistry reduction of complex CO2chemical kinetics: application to a gliding arc plasma | Type | A1 Journal article | ||
Year | 2020 | Publication | Plasma Sources Science & Technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 29 | Issue | 2 | Pages | 025012 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | A gliding arc (GA) plasma has great potential for CO2 conversion into value-added chemicals, because of its high energy efficiency. To improve the application, a 2D/3D fluid model is needed to investigate the CO2 conversion mechanisms in the actual discharge geometry. Therefore, the complex CO2 chemical kinetics description must be reduced due to the huge computational cost associated with 2D/3D models. This paper presents a chemistry reduction method for CO2 plasmas, based on the so-called directed relation graph method. Depending on the defined threshold values, some marginal species are identified. By means of a sensitivity analysis, we can further reduce the chemistry set by removing one by one the marginal species. Based on the socalled flux-sensitivity coupling, we obtain a reduced CO2 kinetics model, consisting of 36 or 15 species (depending on whether the 21 asymmetric mode vibrational states of CO2 are explicitly included or lumped into one group), which is applied to a GA discharge. The results are compared with those predicted with the full chemistry set, and very good agreement is reached. Moreover, the range of validity of the reduced CO2 chemistry set is checked, telling us that this reduced set is suitable for low power GA discharges. Finally, the time and spatial evolution of the CO2 plasma characteristics are presented, based on a 2D model with the reduced kinetics. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000525600600001 | Publication Date | 2020-02-11 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.8 | Times cited | Open Access | ||
Notes | We acknowledge financial support from the Fund for Scientific Research Flanders (FWO; Grant No. G.0383.16 N). The calculations were performed using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UAntwerpen), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UAntwerpen. This work was also supported by the National Natural Science Foundation of China. (Grant Nos. 11735004, 11575019). SR Sun thanks the financial support from the National Postdoctoral Program for Innovative Talents (BX20180029). | Approved | Most recent IF: 3.8; 2020 IF: 3.302 | ||
Call Number | PLASMANT @ plasmant @c:irua:167135 | Serial | 6338 | ||
Permanent link to this record | |||||
Author | Bogaerts, A. | ||||
Title ![]() |
Comprehensive modelling network for dc glow discharges in argon | Type | A1 Journal article | ||
Year | 1999 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 8 | Issue | Pages | 210-229 | |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | |||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Institute of Physics | Place of Publication | Bristol | Editor | |
Language | Wos | 000080660600004 | Publication Date | 2002-08-25 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252;1361-6595; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 27 | Open Access | |
Notes | Approved | Most recent IF: 3.302; 1999 IF: 2.038 | |||
Call Number | UA @ lucian @ c:irua:24129 | Serial | 451 | ||
Permanent link to this record | |||||
Author | Tinck, S.; Bogaerts, A. | ||||
Title ![]() |
Computer simulations of an oxygen inductively coupled plasma used for plasma-assisted atomic layer deposition | Type | A1 Journal article | ||
Year | 2011 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 20 | Issue | 1 | Pages | 015008-015008,10 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | In this paper, an O2 inductively coupled plasma used for plasma enhanced atomic layer deposition of Al2O3 thin films is investigated by means of modeling. This work intends to provide more information about basic plasma properties such as species densities and species fluxes to the substrate as a function of power and pressure, which might be hard to measure experimentally. For this purpose, a hybrid model developed by Kushner et al is applied to calculate the plasma characteristics in the reactor volume for different chamber pressures ranging from 1 to 10 mTorr and different coil powers ranging from 50 to 500 W. Density profiles of the various oxygen containing plasma species are reported as well as fluxes to the substrate under various operating conditions. Furthermore, different orientations of the substrate, which can be placed vertically or horizontally in the reactor, are taken into account. In addition, special attention is paid to the recombination process of atomic oxygen on the different reactor walls under the stated operating conditions. From this work it can be concluded that the plasma properties change significantly in different locations of the reactor. The plasma density near the cylindrical coil is high, while it is almost negligible in the neighborhood of the substrate. Ion and excited species fluxes to the substrate are found to be very low and negligible. Finally, the orientation of the substrate has a minor effect on the flux of O2, while it has a significant effect on the flux of O. In the horizontal configuration, the flux of atomic oxygen can be up to one order of magnitude lower than in the vertical configuration. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Institute of Physics | Place of Publication | Bristol | Editor | |
Language | Wos | 000286592200009 | Publication Date | 2011-01-08 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252;1361-6595; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 11 | Open Access | |
Notes | Approved | Most recent IF: 3.302; 2011 IF: 2.521 | |||
Call Number | UA @ lucian @ c:irua:85285 | Serial | 467 | ||
Permanent link to this record | |||||
Author | Paulussen, S.; Verheyde, B.; Tu, X.; De Bie, C.; Martens, T.; Petrovic, D.; Bogaerts, A.; Sels, B. | ||||
Title ![]() |
Conversion of carbon dioxide to value-added chemicals in atmospheric pressure dielectric barrier discharges | Type | A1 Journal article | ||
Year | 2010 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 19 | Issue | 3 | Pages | 034015,1-034015,6 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | The aim of this work consists of the evaluation of atmospheric pressure dielectric barrier discharges for the conversion of greenhouse gases into useful compounds. Therefore, pure CO2 feed flows are administered to the discharge zone at varying discharge frequency, power input, gas temperature and feed flow rates, aiming at the formation of CO and O2. The discharge obtained in CO2 is characterized as a filamentary mode with a microdischarge zone in each half cycle of the applied voltage. It is shown that the most important parameter affecting the CO2-conversion levels is the gas flow rate. At low flow rates, both the conversion and the CO-yield are significantly higher. In addition, also an increase in the gas temperature and the power input give rise to higher conversion levels, although the effect on the CO-yield is limited. The optimum discharge frequency depends on the power input level and it cannot be unambiguously stated that higher frequencies give rise to increased conversion levels. A maximum CO2 conversion of 30% is achieved at a flow rate of 0.05 L min−1, a power density of 14.75 W cm−3 and a frequency of 60 kHz. The most energy efficient conversions are achieved at a flow rate of 0.2 L min−1, a power density of 11 W cm−3 and a discharge frequency of 30 kHz. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Institute of Physics | Place of Publication | Bristol | Editor | |
Language | Wos | 000277982800016 | Publication Date | 2010-05-22 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252;1361-6595; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 116 | Open Access | |
Notes | Approved | Most recent IF: 3.302; 2010 IF: 2.218 | |||
Call Number | UA @ lucian @ c:irua:82408 | Serial | 512 | ||
Permanent link to this record | |||||
Author | Sun, S.R.; Kolev, S.; Wang, H.X.; Bogaerts, A. | ||||
Title ![]() |
Coupled gas flow-plasma model for a gliding arc: investigations of the back-breakdown phenomenon and its effect on the gliding arc characteristics | Type | A1 Journal article | ||
Year | 2017 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 26 | Issue | 26 | Pages | 015003 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | We present a 3D and 2D Cartesian quasi-neutral plasma model for a low current argon gliding arc discharge, including strong interactions between the gas flow and arc plasma column. The 3D model is applied only for a short time of 0.2 ms due to its huge computational cost. It mainly serves to verify the reliability of the 2D model. As the results in 2D compare well with those in 3D, they can be used for a better understanding of the gliding arc basic characteristics. More specifically, we investigate the back-breakdown phenomenon induced by an artificially controlled plasma channel, and we discuss its effect on the gliding arc characteristics. The back-breakdown phenomenon, or backward-jump motion of the arc, as observed in the experiments, results in a drop of the gas temperature, as well as in a delay of the arc velocity with respect to the gas flow velocity, allowing more gas to pass through the arc, and thus increasing the efficiency of the gliding arc for gas treatment applications. |
||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000419253000001 | Publication Date | 2016-11-22 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 9 | Open Access | OpenAccess |
Notes | This work is financially supported by the Methusalem financing, by the Fund for Scientific Research Flanders (FWO) and by the IAP/7 (Inter-university Attraction Pole) program ‘Physical Chemistry of Plasma-Surface Interactions’ from the Belgian Federal Office for Science Policy (BELSPO). The work was carried out in part using the Turing HPC infrastructure of the CalcUA core facility of the Universiteit Antwerpen, a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the Universiteit Antwerpen. This work was also supported by the National Natural Science Foundation of China (Grant Nos. 11275021, 11575019). S R Sun thanks the financial support from the China Scholarship Council. | Approved | Most recent IF: 3.302 | ||
Call Number | PLASMANT @ plasmant @ c:irua:138993 | Serial | 4337 | ||
Permanent link to this record | |||||
Author | Wang, W.; Berthelot, A.; Kolev, S.; Tu, X.; Bogaerts, A. | ||||
Title ![]() |
CO2 conversion in a gliding arc plasma: 1D cylindrical discharge model | Type | A1 Journal article | ||
Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 25 | Issue | 25 | Pages | 065012 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | CO 2 conversion by a gliding arc plasma is gaining increasing interest, but the underlying mechanisms for an energy-efficient process are still far from understood. Indeed, the chemical complexity of the non-equilibrium plasma poses a challenge for plasma modeling due to the huge computational load. In this paper, a one-dimensional (1D) gliding arc model is developed in a cylindrical frame, with a detailed non-equilibrium CO 2 plasma chemistry set, including the CO 2 vibrational kinetics up to the dissociation limit. The model solves a set of time- dependent continuity equations based on the chemical reactions, as well as the electron energy balance equation, and it assumes quasi-neutrality in the plasma. The loss of plasma species and heat due to convection by the transverse gas flow is accounted for by using a characteristic frequency of convective cooling, which depends on the gliding arc radius, the relative velocity of the gas flow with respect to the arc and on the arc elongation rate. The calculated values for plasma density and plasma temperature within this work are comparable with experimental data on gliding arc plasma reactors in the literature. Our calculation results indicate that excitation to the vibrational levels promotes efficient dissociation in the gliding arc, and this is consistent with experimental investigations of the gliding arc based CO 2 conversion in the literature. Additionally, the dissociation of CO 2 through collisions with O atoms has the largest contribution to CO 2 splitting under the conditions studied. In addition to the above results, we also demonstrate that lumping the CO 2 vibrational states can bring a significant reduction of the computational load. The latter opens up the way for 2D or 3D models with an accurate description of the CO 2 vibrational kinetics. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000386605100002 | Publication Date | 2016-10-18 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 3 | Open Access | |
Notes | This research was supported by the European Marie Skłodowska-Curie Individual Fellowship ‘GlidArc’ within Horizon2020 (Grant No. 657304) and by the FWO project (grant G.0383.16N). The calculations were performed using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UAntwerpen), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UAntwerpen. | Approved | Most recent IF: 3.302 | ||
Call Number | PLASMANT @ plasmant @ c:irua:135990 | Serial | 4286 | ||
Permanent link to this record | |||||
Author | Bogaerts, A.; Berthelot, A.; Heijkers, S.; Kolev, S.; Snoeckx, R.; Sun, S.; Trenchev, G.; Van Laer, K.; Wang, W. | ||||
Title ![]() |
CO2conversion by plasma technology: insights from modeling the plasma chemistry and plasma reactor design | Type | A1 Journal article | ||
Year | 2017 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 26 | Issue | 26 | Pages | 063001 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | In recent years there has been growing interest in the use of plasma technology for CO2 conversion. To improve this application, a good insight into the underlying mechanisms is of great importance. This can be obtained from modeling the detailed plasma chemistry in order to understand the chemical reaction pathways leading to CO2 conversion (either in pure form or mixed with another gas). Moreover, in practice, several plasma reactor types are being investigated for CO2 conversion, so in addition it is essential to be able to model these reactor geometries so that their design can be improved, and the most energy efficient CO2 conversion can be achieved. Modeling the detailed plasma chemistry of CO2 conversion in complex reactors is, however, very time-consuming. This problem can be overcome by using a combination of two different types of model: 0D chemical reaction kinetics models are very suitable for describing the detailed plasma chemistry, while the characteristic features of different reactor geometries can be studied by 2D or 3D fluid models. In the first instance the latter can be developed in argon or helium with a simple chemistry to limit the calculation time; however, the ultimate aim is to implement the more complex CO2 chemistry in these models. In the present paper, examples will be given of both the 0D plasma chemistry models and the 2D and 3D fluid models for the most common plasma reactors used for CO2 conversion in order to emphasize the complementarity of both approaches. Furthermore, based on the modeling insights, the paper discusses the possibilities and limitations of plasma-based CO2 conversion in different types of plasma reactors, as well as what is needed to make further progress in this field. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000412173700001 | Publication Date | 2017-05-15 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 26 | Open Access | OpenAccess |
Notes | We would like to thank T Silva, N Britoun, Th Godfroid and R Snyders (Université de Mons and Materia Nova Research Center), A Ozkan, Th Dufour and F Reniers (Université Libre de Bruxelles) andK Van Wesenbeeck and S Lenaerts (University of Antwerp) for providingexperimental data to validate our models. Furthermore, we acknowledge the financial support from the IAP/7 (Inter-university Attraction Pole) program ‘PSI-Physical Chemistry of Plasma-Surface Interactions’ by the Belgian Federal Office for Science Policy (BELSPO), the Francqui Research Foundation, the European Union’s Seventh Framework Programme for research, technological development and demonstration under grant agreement no. 606889, the European Marie Skłodowska- Curie Individual Fellowship project ‘GlidArc’ within Horizon2020, the Methusalem financing of the University of Antwerp, the Fund for Scientific Research, Flanders (FWO; grant nos. G.0383.16N and 11U5316N) and the Institute for the Promotion of Innovation by Science and Technology in Flanders (IWT Flanders). The calculations were carried out using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UAntwerpen), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UAntwerpen. | Approved | Most recent IF: 3.302 | ||
Call Number | PLASMANT @ plasmant @ c:irua:144429 | Serial | 4614 | ||
Permanent link to this record | |||||
Author | Ozkan, A.; Dufour, T.; Silva, T.; Britun, N.; Snyders, R.; Reniers, F.; Bogaerts, A. | ||||
Title ![]() |
DBD in burst mode: solution for more efficient CO2conversion? | Type | A1 Journal article | ||
Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 25 | Issue | 25 | Pages | 055005 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | CO2 conversion into value-added products has gained significant interest over the few last years, as the greenhouse gas concentrations constantly increase due to anthropogenic activities. Here we report on experiments for CO2 conversion by means of a cold atmospheric plasma using a cylindrical flowing dielectric barrier discharge (DBD) reactor. A detailed comparison of this DBD ignited in a so-called burst mode (i.e. where an AC voltage is applied during a limited amount of time) and pure AC mode is carried out to evaluate their effect on the conversion of CO2 as well as on the energy efficiency. Decreasing the duty cycle in the burst mode from 100% (i.e. corresponding to pure AC mode) to 40% leads to a rise in the conversion from 16–26% and to a rise in the energy efficiency from 15 to 23%. Based on a detailed electrical analysis, we show that the conversion correlates with the features of the microfilaments. Moreover, the root-mean-square voltage in the burst mode remains constant as a function of the process time for the duty cycles <70%, while a higher duty cycle or the usual pure AC mode leads to a clear voltage decay by more than 500 V, over approximately 90 s, before reaching a steady state regime. The higher plasma voltage in the burst mode yields a higher electric field. This causes the increasing the electron energy, and therefore their involvement in the CO2 dissociation process, which is an additional explanation for the higher CO2 conversion and energy efficiency in the burst mode. |
||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000403945500005 | Publication Date | 2016-08-02 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 17 | Open Access | |
Notes | The authors acknowledge financial support from the IAPVII/ 12, P7/34 (Inter-university Attraction Pole) program ‘PSI-Physical Chemistry of Plasma-Surface Interactions’, financially supported by the Belgian Federal Office for Science Policy (BELSPO). A. Ozkan would also like to thank financial support given by ‘Fonds David et Alice Van Buuren’. | Approved | Most recent IF: 3.302 | ||
Call Number | c:irua:134841 | Serial | 4107 | ||
Permanent link to this record | |||||
Author | De Bie, C.; Martens, T.; van Dijk, J.; Paulussen, S.; Verheyde, B.; Corthals, S.; Bogaerts, A. | ||||
Title ![]() |
Dielectric barrier discharges used for the conversion of greenhouse gases: modeling the plasma chemistry by fluid simulations | Type | A1 Journal article | ||
Year | 2011 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 20 | Issue | 2 | Pages | 024008,1-024008,11 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | The conversion of methane to value-added chemicals and fuels is considered to be one of the challenges of the 21st century. In this paper we study, by means of fluid modeling, the conversion of methane to higher hydrocarbons or oxygenates by partial oxidation with CO2 or O2 in a dielectric barrier discharge. Sixty-nine different plasma species (electrons, ions, molecules, radicals) are included in the model, as well as a comprehensive set of chemical reactions. The calculation results presented in this paper include the conversion of the reactants and the yields of the reaction products as a function of residence time in the reactor, for different gas mixing ratios. Syngas (i.e. H2 + CO) and higher hydrocarbons (C2Hx) are typically found to be important reaction products. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Institute of Physics | Place of Publication | Bristol | Editor | |
Language | Wos | 000290719900009 | Publication Date | 2011-04-02 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252;1361-6595; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 38 | Open Access | |
Notes | Approved | Most recent IF: 3.302; 2011 IF: 2.521 | |||
Call Number | UA @ lucian @ c:irua:87868 | Serial | 689 | ||
Permanent link to this record | |||||
Author | Peerenboom, K.; Parente, A.; Kozák, T.; Bogaerts, A.; Degrez, G. | ||||
Title ![]() |
Dimension reduction of non-equilibrium plasma kinetic models using principal component analysis | Type | A1 Journal article | ||
Year | 2015 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 24 | Issue | 24 | Pages | 025004 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | The chemical complexity of non-equilibrium plasmas poses a challenge for plasma modeling because of the computational load. This paper presents a dimension reduction method for such chemically complex plasmas based on principal component analysis (PCA). PCA is used to identify a low-dimensional manifold in chemical state space that is described by a small number of parameters: the principal components. Reduction is obtained since continuity equations only need to be solved for these principal components and not for all the species. Application of the presented method to a CO2 plasma model including state-to-state vibrational kinetics of CO2 and CO demonstrates the potential of the PCA method for dimension reduction. A manifold described by only two principal components is able to predict the CO2 to CO conversion at varying ionization degrees very accurately. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Institute of Physics | Place of Publication | Bristol | Editor | |
Language | Wos | 000356816200008 | Publication Date | 2015-01-27 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252;1361-6595; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 11 | Open Access | |
Notes | Approved | Most recent IF: 3.302; 2015 IF: 3.591 | |||
Call Number | c:irua:123534 | Serial | 704 | ||
Permanent link to this record | |||||
Author | Wang, L.; Wen, D.-Q.; Zhang, Q.-Z.; Song, Y.-H.; Zhang, Y.-R.; Wang, Y.-N. | ||||
Title ![]() |
Disruption of self-organized striated structure induced by secondary electron emission in capacitive oxygen discharges | Type | A1 Journal article | ||
Year | 2019 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 28 | Issue | 5 | Pages | 055007 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | Self-organized striated structure has been observed experimentally and numerically in CF4 plasmas in radio-frequency capacitively coupled plasmas recently (Liu et al 2016 Phys. Rev. Lett. 116 255002). In this work, the striated structure is investigated in a capacitively coupled oxygen discharge with the introduction of the effect from the secondary electron emission, based on a particle-in-cell/Monte Carlo collision model. As we know, the transport of positive and negative ions plays a key role in the formation of striations in electronegative gases, for which, the electronegativity needs to be large enough. As the secondary electron emission increases, electrons in the sheaths gradually contribute more ionization to the discharge. Meanwhile, the increase of the electron density, especially in the plasma bulk, leads to an increased electrical conductivity and a reduced bulk electric field, which would shield the ions' mobility. These changes result in enlarged striation gaps. And then, with more emitted electrons, obvious disruption of the striations is observed accompanied with a transition of electron heating mode. Due to the weakened field, the impact ionization in the plasma bulk is attenuated, compared with the enhanced ionization caused by secondary electrons. This would lead to the electron heating mode transition from striated (STR) mode to gamma-mode. Besides, our investigation further reveals that gamma-mode is more likely to dominate the discharge under high gas pressures or driving voltages. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000467827800001 | Publication Date | 2019-04-09 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 2 | Open Access | Not_Open_Access: Available from 13.05.2020 |
Notes | Approved | Most recent IF: 3.302 | |||
Call Number | UA @ admin @ c:irua:160365 | Serial | 5270 | ||
Permanent link to this record | |||||
Author | Zhang, L.; Heijkers, S.; Wang, W.; Martini, L.M.; Tosi, P.; Yang, D.; Fang, Z.; Bogaerts, A. | ||||
Title ![]() |
Dry reforming of methane in a nanosecond repetitively pulsed discharge: chemical kinetics modeling | Type | A1 Journal article | ||
Year | 2022 | Publication | Plasma Sources Science & Technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 31 | Issue | 5 | Pages | 055014 |
Keywords | A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | Nanosecond pulsed discharge plasma shows a high degree of non-equilibrium, and exhibits relatively high conversions in the dry reforming of methane. To further improve the application, a good insight of the underlying mechanisms is desired. We developed a chemical kinetics model to explore the underlying plasma chemistry in nanosecond pulsed discharge. We compared the calculated conversions and product selectivities with experimental results, and found reasonable agreement in a wide range of specific energy input. Hence, the chemical kinetics model is able to provide insight in the underlying plasma chemistry. The modeling results predict that the most important dissociation reaction of CO<sub>2</sub>and CH<sub>4</sub>is electron impact dissociation. C<sub>2</sub>H<sub>2</sub>is the most abundant hydrocarbon product, and it is mainly formed upon reaction of two CH<sub>2</sub>radicals. Furthermore, the vibrational excitation levels of CO<sub>2</sub>contribute for 85% to the total dissociation of CO<sub>2</sub>. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000797660000001 | Publication Date | 2022-05-01 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record | |
Impact Factor | 3.8 | Times cited | Open Access | OpenAccess | |
Notes | China Scholarship Council; National Natural Science Foundation of China, 11965018 ; This work is supported by the National Natural Science Foundation of China (Grant Nos. 52077026, 11965018), L Zhang was also supported by the China Scholarship Council (CSC). Data availability statement The data that support the findings of this study are available upon reasonable request from the authors. | Approved | Most recent IF: 3.8 | ||
Call Number | PLASMANT @ plasmant @c:irua:188537 | Serial | 7069 | ||
Permanent link to this record | |||||
Author | Bal, K.M.; Huygh, S.; Bogaerts, A.; Neyts, E.C. | ||||
Title ![]() |
Effect of plasma-induced surface charging on catalytic processes: application to CO2activation | Type | A1 Journal article | ||
Year | 2018 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 27 | Issue | 2 | Pages | 024001 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | Understanding the nature and effect of the multitude of plasma–surface interactions in plasma catalysis is a crucial requirement for further process development and improvement. A particularly intriguing and rather unique property of a plasma-catalytic setup is the ability of the plasma to modify the electronic structure, and hence chemical properties, of the catalyst through charging, i.e. the absorption of excess electrons. In this work, we develop a quantum chemical model based on density functional theory to study excess negative surface charges in a heterogeneous catalyst exposed to a plasma. This method is specifically applied to investigate plasma-catalytic CO2 activation on supported M/Al2O3 (M=Ti, Ni, Cu) single atom catalysts. We find that (1) the presence of a negative surface charge dramatically improves the reductive power of the catalyst, strongly promoting the splitting of CO2 to CO and oxygen, and (2) the relative activity of the investigated transition metals is also changed upon charging, suggesting that controlled surface charging is a powerful additional parameter to tune catalyst activity and selectivity. These results strongly point to plasma-induced surface charging of the catalyst as an important factor contributing to the plasma-catalyst synergistic effects frequently reported for plasma catalysis. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000424520100001 | Publication Date | 2018-02-07 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 19 | Open Access | OpenAccess |
Notes | KMB is funded as PhD fellow (aspirant) of the FWO-Flanders (Research Foundation—Flanders), Grant 11V8915N. The computational resources and services used in this work were provided by the VSC (Flemish Supercomputer Center), funded by the FWO and the Flemish Government— department EWI. | Approved | Most recent IF: 3.302 | ||
Call Number | PLASMANT @ plasmant @c:irua:149285 | Serial | 4813 | ||
Permanent link to this record | |||||
Author | Wang, W.; Bogaerts, A. | ||||
Title ![]() |
Effective ionisation coefficients and critical breakdown electric field of CO2at elevated temperature: effect of excited states and ion kinetics | Type | A1 Journal article | ||
Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 25 | Issue | 25 | Pages | 055025 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | Electrical breakdown by the application of an electric field occurs more easily in hot gases than in cold gases because of the extra electron-species interactions that occur as a result of dissociation, ionization and excitation at higher temperature. This paper discusses some overlooked physics and clarifies inaccuracies in the evaluation of the effective ionization coefficients and the critical reduced breakdown electric field of CO2 at elevated temperature, considering the influence of excited states and ion kinetics. The critical reduced breakdown electric field is obtained by balancing electron generation and loss mechanisms using the electron energy distribution function (EEDF) derived from the Boltzmann transport equation under the two-term approximation. The equilibrium compositions of the hot gas mixtures are determined based on Gibbs free energy minimization considering the ground states as well as vibrationally and electronically excited states as independent species, which follow a Boltzmann distribution with a fixed excitation temperature. The interaction cross sections between electrons and the excited species, not reported previously, are properly taken into account. Furthermore, the ion kinetics, including electron–ion recombination, associative electron detachment, charge transfer and ion conversion into stable negative ion clusters, are also considered. Our results indicate that the excited species lead to a greater population of high-energy electrons at higher gas temperature and this affects the Townsend rate coefficients (i.e. of electron impact ionization and attachment), but the critical reduced breakdown electric field strength of CO2 is only affected when also properly accounting for the ion kinetics. Indeed, the latter greatly influences the effective ionization coefficients and hence the critical reduced breakdown electric field at temperatures above 1500 K. The rapid increase of the dissociative electron attachment cross-section of molecular oxygen with rising vibrational quantum number leads to a larger electron loss rate and this enhances the critical reduced breakdown electric field strength in the temperature range where the concentration of molecular oxygen is relatively high. The results obtained in this work show reasonable agreement with experimental results from literature, and are important for the evaluation of the dielectric strength of CO2 in a highly reactive environment at elevated temperature. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000385494000006 | Publication Date | 2016-09-22 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 3 | Open Access | |
Notes | Skłodowska-Curie Individual Fellowship ‘GlidArc’ within Horizon2020 (Grant No.657304) and the FWO project (grant G.0383.16N). The computational work was carried out using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UA), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UA. | Approved | Most recent IF: 3.302 | ||
Call Number | PLASMANT @ plasmant @ c:irua:135515 | Serial | 4281 | ||
Permanent link to this record | |||||
Author | Liu, Y.-X.; Zhang, Q.-Z.; Liu, L.; Song, Y.-H.; Bogaerts, A.; Wang, Y.-N. | ||||
Title ![]() |
Electron bounce resonance heating in dual-frequency capacitively coupled oxygen discharges | Type | A1 Journal article | ||
Year | 2013 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 22 | Issue | 2 | Pages | 025012-11 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | The electron bounce resonance heating (BRH) in dual-frequency capacitively coupled plasmas operated in oxygen is studied by different experimental methods and a particle-in-cell/Monte Carlo collision (PIC/MCC) simulation, and compared with the electropositive argon discharge. In comparison with argon, the experimental results show that in an oxygen discharge the resonance peaks in positive-ion density and light intensity tend to occur at larger electrode gaps. Moreover, at electrode gaps L > 2.5 cm, the positive-ion (and electron) density and the light emission drop monotonically in the oxygen discharge upon increasing L, whereas they rise (after an initial drop) in the argon case. At resonance gap the electronegativity reaches its maximum due to the BRH. All these experimental observations are explained by PIC/MCC simulations, which show that in the oxygen discharge the bulk electric field becomes quite strong and is out of phase with the sheath field. Therefore, it retards the resonance electrons when traversing the bulk, resulting in a suppressed BRH. Both experiment and simulation results show that this effect becomes more pronounced at lower high-frequency power, when the discharge mode changes from electropositive to electronegative. In a pure oxygen discharge, the BRH is suppressed with increasing pressure and almost diminishes at 12 Pa. Finally, the driving frequency significantly affects the BRH, because it determines the phase relation between bulk electric field and sheath electric field. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Institute of Physics | Place of Publication | Bristol | Editor | |
Language | Wos | 000317275400014 | Publication Date | 2013-03-18 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252;1361-6595; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 20 | Open Access | |
Notes | Approved | Most recent IF: 3.302; 2013 IF: 3.056 | |||
Call Number | UA @ lucian @ c:irua:106534 | Serial | 911 | ||
Permanent link to this record | |||||
Author | Yan, M.; Bogaerts, A.; Goedheer, W.J.; Gijbels, R. | ||||
Title ![]() |
Electron energy distribution function in capacitively coupled RF discharges: differences between electropositive Ar and electronegative SiH4 discharges | Type | A1 Journal article | ||
Year | 2000 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 9 | Issue | Pages | 583-591 | |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | |||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Institute of Physics | Place of Publication | Bristol | Editor | |
Language | Wos | 000165341000015 | Publication Date | 2002-08-25 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252;1361-6595; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 21 | Open Access | |
Notes | Approved | Most recent IF: 3.302; 2000 IF: 1.963 | |||
Call Number | UA @ lucian @ c:irua:34071 | Serial | 929 | ||
Permanent link to this record | |||||
Author | Zhang, Y.-R.; Neyts, E.C.; Bogaerts, A. | ||||
Title ![]() |
Enhancement of plasma generation in catalyst pores with different shapes | Type | A1 Journal article | ||
Year | 2018 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 27 | Issue | 5 | Pages | 055008 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | Plasma generation inside catalyst pores is of utmost importance for plasma catalysis, as the existence of plasma species inside the pores affects the active surface area of the catalyst available to the plasma species for catalytic reactions. In this paper, the electric field enhancement, and thus the plasma production inside catalyst pores with different pore shapes is studied with a two-dimensional fluid model. The results indicate that the electric field will be significantly enhanced near tip-like structures. In a conical pore with small opening, the strongest electric field appears at the opening and bottom corners of the pore, giving rise to a prominent ionization rate throughout the pore. For a cylindrical pore, the electric field is only enhanced at the bottom corners of the pore, with lower absolute value, and thus the ionization rate inside the pore is only slightly enhanced. Finally, in a conical pore with large opening, the electric field is characterized by a maximum at the bottom of the pore, yielding a similar behavior for the ionization rate. These results demonstrate that the shape of the pore has a significantly influence on the electric field enhancement, and thus modifies the plasma properties. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000432351700002 | Publication Date | 2018-05-15 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 11 | Open Access | OpenAccess |
Notes | This work was supported by the Fund for Scientific Research Flanders (FWO) (Grant No. G.0217.14N) and the Fundamental Research Funds for the Central Universities (Grant No. DUT17LK52). | Approved | Most recent IF: 3.302 | ||
Call Number | PLASMANT @ plasmant @c:irua:151546 | Serial | 4998 | ||
Permanent link to this record | |||||
Author | Van Laer, K.; Tinck, S.; Samara, V.; de Marneffe, J.F.; Bogaerts, A. | ||||
Title ![]() |
Etching of low-k materials for microelectronics applications by means of a N2/H2 plasma : modeling and experimental investigation | Type | A1 Journal article | ||
Year | 2013 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 22 | Issue | 2 | Pages | 025011-25019 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | In this paper, we investigate the etch process of so-called low-k organic material by means of a N2/H2 capacitively coupled plasma, as applied in the micro-electronics industry for the manufacturing of computer chips. In recent years, such an organic material has emerged as a possible alternative for replacing bulk SiO2 as a dielectric material in the back-end-of-line, because of the smaller parasitic capacity between adjacent conducting lines, and thus a faster propagation of the electrical signals throughout the chip. Numerical simulations with a hybrid plasma model, using an extensive plasma and surface chemistry set, as well as experiments are performed, focusing on the plasma properties as well as the actual etching process, to obtain a better insight into the underlying mechanisms. Furthermore, the effects of gas pressure, applied power and gas composition are investigated to try to optimize the etch process. In general, the plasma density reaches a maximum near the wafer edge due to the so-called 'edge effect'. As a result, the etch rate is not uniform but will also reach its maximum near the wafer edge. The pressure seems not to have a big effect. A higher power increases the etch rate, but the uniformity becomes (slightly) worse. The gas mixing ratio has no significant effect on the etch process, except when a pure H2 or N2 plasma is used, illustrating the synergistic effects of a N2/H2 plasma. In fact, our calculations reveal that the N2/H2 plasma entails an ion-enhanced etch process. The simulation results are in reasonable agreement with the experimental values. The microscopic etch profile shows the desired anisotropic shape under all conditions under study. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Institute of Physics | Place of Publication | Bristol | Editor | |
Language | Wos | 000317275400013 | Publication Date | 2013-03-18 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252;1361-6595; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 13 | Open Access | |
Notes | Approved | Most recent IF: 3.302; 2013 IF: 3.056 | |||
Call Number | UA @ lucian @ c:irua:106654 | Serial | 1084 | ||
Permanent link to this record | |||||
Author | Kozák, T.; Bogaerts, A. | ||||
Title ![]() |
Evaluation of the energy efficiency of CO2 conversion in microwave discharges using a reaction kinetics model | Type | A1 Journal article | ||
Year | 2015 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 24 | Issue | 24 | Pages | 015024 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | We use a zero-dimensional reaction kinetics model to simulate CO2 conversion in microwave discharges where the excitation of the vibrational levels plays a significant role in the dissociation kinetics. The model includes a description of the CO2 vibrational kinetics, taking into account state-specific VT and VV relaxation reactions and the effect of vibrational excitation on other chemical reactions. The model is used to simulate a general tubular microwave reactor, where a stream of CO2 flows through a plasma column generated by microwave radiation. We study the effects of the internal plasma parameters, namely the reduced electric field, electron density and the total specific energy input, on the CO2 conversion and its energy efficiency. We report the highest energy efficiency (up to 30%) for a specific energy input in the range 0.41.0 eV/molecule and a reduced electric field in the range 50100 Td and for high values of the electron density (an ionization degree greater than 10−5). The energy efficiency is mainly limited by the VT relaxation which contributes dominantly to the vibrational energy losses and also contributes significantly to the heating of the reacting gas. The model analysis provides useful insight into the potential and limitations of CO2 conversion in microwave discharges. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Institute of Physics | Place of Publication | Bristol | Editor | |
Language | Wos | 000348298200025 | Publication Date | 2014-12-23 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252;1361-6595; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 100 | Open Access | |
Notes | Approved | Most recent IF: 3.302; 2015 IF: 3.591 | |||
Call Number | c:irua:122243 | Serial | 1087 | ||
Permanent link to this record | |||||
Author | Van Laer, K.; Bogaerts, A. | ||||
Title ![]() |
Fluid modelling of a packed bed dielectric barrier discharge plasma reactor | Type | A1 Journal article | ||
Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 25 | Issue | 25 | Pages | 015002 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | A packed bed dielectric barrier discharge plasma reactor is computationally studied with a fluid model. Two different complementary axisymmetric 2D geometries are used to mimic the intrinsic 3D problem. It is found that a packing enhances the electric field strength and electron temperature at the contact points of the dielectric material due to polarization of the beads by the applied potential. As a result, these contact points prove to be of direct importance to initiate the plasma. At low applied potential, the discharge stays at the contact points, and shows the properties of a Townsend discharge. When a high enough potential is applied, the plasma will be able to travel through the gaps in between the beads from wall to wall, forming a kind of glow discharge. Therefore, the inclusion of a so-called ‘channel of voids’ is indispensable in any type of packed bed modelling. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000370974800009 | Publication Date | 2015-12-01 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 50 | Open Access | |
Notes | The authors gratefully thank St Kolev for the many interesting discussions and the useful advise in setting up the models. This research was carried out in the framework of the network on Physical Chemistry of Plasma-Surface Interactions— Interuniversity Attraction Poles, phase VII (http://psi-iap7.ulb. ac.be/), and supported by the Belgian Science Policy Office (BELSPO). K Van Laer is indebted to the Institute for the Promotion of Innovation by Science and Technology in Flanders (IWT Flanders) for financial support. | Approved | Most recent IF: 3.302 | ||
Call Number | c:irua:129802 | Serial | 3982 | ||
Permanent link to this record | |||||
Author | Zhang, Y.; Wang, H.-yu; Zhang, Y.-ru; Bogaerts, A. | ||||
Title ![]() |
Formation of microdischarges inside a mesoporous catalyst in dielectric barrier discharge plasmas | Type | A1 Journal article | ||
Year | 2017 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 26 | Issue | 26 | Pages | 054002 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | The formation process of a microdischarge (MD) in both μm- and nm-sized catalyst pores is simulated by a two-dimensional particle-in-cell/Monte Carlo collision model. A parallel-plate dielectric barrier discharge configuration in filamentary mode is considered in ambient air. The discharge is powered by a high voltage pulse. Our calculations reveal that a streamer can penetrate into the surface features of a porous catalyst and MDs can be formed inside both μm- and nm-sized pores, yielding ionization inside the pore. For the μm-sized pores, the ionization mainly occurs inside the pore, while for the nm-sized pores the ionization is strongest near and inside the pore. Thus, enhanced discharges near and inside the mesoporous catalyst are observed. Indeed, the maximum values of the electric field, ionization rate and electron density occur near and inside the pore. The maximum electric field and electron density inside the pore first increase when the pore size rises from 4 nm to 10 nm, and then they decrease for the 100 nm pore, due to a more pronounced surface discharge for the smaller pores. However, the ionization rate is highest for the 100 nm pore due to the largest effective ionization region. |
||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000399277700001 | Publication Date | 2017-04-05 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 15 | Open Access | OpenAccess |
Notes | This work was supported by the NSFC (11405067, 11275007, 11375163). Y Zhang gratefully acknowledges the Belgian Federal Science Policy Office for financial support. The authors are very grateful to Wei Jiang for the useful discussions on the photo-ionization model and the particle-incell/ Monte-Carlo model. | Approved | Most recent IF: 3.302 | ||
Call Number | PLASMANT @ plasmant @ c:irua:142806 | Serial | 4566 | ||
Permanent link to this record | |||||
Author | Alves, L.L.; Bogaerts, A.; Guerra, V.; Turner, M.M. | ||||
Title ![]() |
Foundations of modelling of nonequilibrium low-temperature plasmas | Type | A1 Journal article | ||
Year | 2018 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 27 | Issue | 2 | Pages | 023002 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | This work explains the need for plasma models, introduces arguments for choosing the type of model that better fits the purpose of each study, and presents the basics of the most common nonequilibrium low-temperature plasma models and the information available from each one, along with an extensive list of references for complementary in-depth reading. The paper presents the following models, organised according to the level of multi-dimensional description of the plasma: kinetic models, based on either a statistical particle-in-cell/Monte-Carlo approach or the solution to the Boltzmann equation (in the latter case, special focus is given to the description of the electron kinetics); multi-fluid models, based on the solution to the hydrodynamic equations; global (spatially-average) models, based on the solution to the particle and energy rate-balance equations for the main plasma species, usually including a very complete reaction chemistry; mesoscopic models for plasma–surface interaction, adopting either a deterministic approach or a stochastic dynamical Monte-Carlo approach. For each plasma model, the paper puts forward the physics context, introduces the fundamental equations, presents advantages and limitations, also from a numerical perspective, and illustrates its application with some examples. Whenever pertinent, the interconnection between models is also discussed, in view of multi-scale hybrid approaches. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000425688600001 | Publication Date | 2018-02-20 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 17 | Open Access | OpenAccess |
Notes | The authors would like to thank A Tejero-Del-Caz and A Berthelot for their technical contributions in writing the manuscript. This work was partially funded by Portuguese FCT —Fundação para a Ciência e a Tecnologia, under projects UID/ FIS/50010/2013, PTDC/FISPLA/1243/2014 (KIT-PLAS- MEBA) and PTDC/FIS-PLA/1420/2014 (PREMiERE). | Approved | Most recent IF: 3.302 | ||
Call Number | PLASMANT @ plasmant @c:irua:149391 | Serial | 4810 | ||
Permanent link to this record | |||||
Author | Bogaerts, A.; Neyts, E.C.; Guaitella, O.; Murphy, A.B. | ||||
Title ![]() |
Foundations of plasma catalysis for environmental applications | Type | A1 Journal article | ||
Year | 2022 | Publication | Plasma Sources Science & Technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | Issue | Pages | |||
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | Plasma catalysis is gaining increasing interest for various applications, but the underlying mechanisms are still far from understood. Hence, more fundamental research is needed to understand these mechanisms. This can be obtained by both modelling and experiments. This foundations paper describes the fundamental insights in plasma catalysis, as well as efforts to gain more insights by modelling and experiments. Furthermore, it discusses the state-of-the-art of the major plasma catalysis applications, as well as successes and challenges of technology transfer of these applications. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000804396200001 | Publication Date | 2022-03-21 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.8 | Times cited | Open Access | OpenAccess | |
Notes | H2020 Marie Skłodowska-Curie Actions, 823745 ; H2020 European Research Council, 810182 ; We acknowldege financial support from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation programme (Grant Agreement No. 810182 – SCOPE ERC Synergy project) and the European Union’s Horizon 2020 Research and Innovation programme under the Marie Sklodowska-Curie Grant Agreement No. 813393 (PIONEER). | Approved | Most recent IF: 3.8 | ||
Call Number | PLASMANT @ plasmant @c:irua:188539 | Serial | 7070 | ||
Permanent link to this record | |||||
Author | Zhao, S.-X.; Gao, F.; Wang, Y.-N.; Bogaerts, A. | ||||
Title ![]() |
Gas ratio effects on the Si etch rate and profile uniformity in an inductively coupled Ar/CF4 plasma | Type | A1 Journal article | ||
Year | 2013 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 22 | Issue | 1 | Pages | 015017-15018 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | In this work, a hybrid model is used to investigate the effect of different gas ratios on the Si etching and polymer film deposition characteristics in an Ar/CF4 inductively coupled plasma. The influence of the surface processes on the bulk plasma properties is studied, and also the spatial characteristics of important gas phase and etched species. The densities of F and CF2 decrease when the surface module is included in the simulations, due to the species consumption caused by etching and polymer deposition. The influence of the surface processes on the bulk plasma depends on the Ar/CF4 gas ratio. The deposited polymer becomes thicker at high CF4 content because of more abundant CFx radicals. As a result of the competition between the polymer thickness and the F flux, the etch rate first increases and then decreases upon increasing the CF4 content. The electron properties, more specifically the electron density profile, affect the Si etch characteristics substantially by determining the radical density and flux profiles. In fact, the radial profile of the etch rate is more uniform at low CF4 content since the electron density has a smooth distribution. At high CF4 content, the etch rate is less uniform with a minimum halfway along the wafer radius, because the electron density distribution is more localized. Therefore, our calculations predict that it is better to work at relatively high Ar/CF4 gas ratios, in order to obtain high etch rate and good profile uniformity for etch applications. This, in fact, corresponds to the typical experimental etch conditions in Ar/CF4 gas mixtures as found in the literature, where Ar is typically present at a much higher concentration than CF4. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Institute of Physics | Place of Publication | Bristol | Editor | |
Language | Wos | 000314966300022 | Publication Date | 2012-12-20 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252;1361-6595; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 11 | Open Access | |
Notes | Approved | Most recent IF: 3.302; 2013 IF: 3.056 | |||
Call Number | UA @ lucian @ c:irua:102583 | Serial | 1320 | ||
Permanent link to this record | |||||
Author | Zhang, Q.-Z.; Liu, Y.-X.; Jiang, W.; Bogaerts, A.; Wang, Y.-N. | ||||
Title ![]() |
Heating mechanism in direct current superposed single-frequency and dual-frequency capacitively coupled plasmas | Type | A1 Journal article | ||
Year | 2013 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 22 | Issue | 2 | Pages | 025014-25018 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | In this work particle-in-cell/Monte Carlo collision simulations are performed to study the heating mechanism and plasma characteristics in direct current (dc) superposed radio-frequency (RF) capacitively coupled plasmas, operated both in single-frequency (SF) and dual-frequency (DF) regimes. An RF (60/2 MHz) source is applied on the bottom electrode to sustain the discharge, and a dc source is fixed on the top electrode. The heating mechanism appears to be very different in dc superposed SF and DF discharges. When only a single source of 60 MHz is applied, the plasma bulk region is reduced by the dc source, thus the ionization rate and hence the electron density decrease with rising dc voltage. However, when a DF source of 60 and 2 MHz is applied, the electron density can increase upon addition of a dc voltage, depending on the gap length and applied dc voltage. This is explained from the spatiotemporal ionization rates in the DF discharge. In fact, a completely different behavior is observed for the ionization rate in the two half-periods of the LF source. In the first LF half-period, the situation resembles the dc superposed SF discharge, and the reduced plasma bulk region due to the negative dc bias results in a very small effective discharge area and a low ionization rate. On the other hand, in the second half-period, the negative dc bias is to some extent counteracted by the LF voltage, and the sheath close to the dc electrode becomes particularly thin. Consequently, the amplitude of the high-frequency sheath oscillations at the top electrode is largely enhanced, while the LF sheath at the bottom electrode is in its expanding phase and can thus well confine the high-energy electrons. Therefore, the ionization rate increases considerably in this second LF half-period. Furthermore, in addition to the comparison between SF and DF discharges and the effect of gap length and dc voltage, the effect of secondary electrons is examined. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Institute of Physics | Place of Publication | Bristol | Editor | |
Language | Wos | 000317275400016 | Publication Date | 2013-03-28 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252;1361-6595; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 9 | Open Access | |
Notes | Approved | Most recent IF: 3.302; 2013 IF: 3.056 | |||
Call Number | UA @ lucian @ c:irua:106877 | Serial | 1413 | ||
Permanent link to this record |