| |
Records |
Links |
|
Author |
Bampouli, A.; Goris, Q.; Hussain, M.N.; Louisnard, O.; Stefanidis, G.D.; Van Gerven, T. |
|
| |
Title |
Importance of design and operating parameters in a sonication system for viscous solutions : effects of input power, horn tip diameter and reactor capacity |
Type |
A1 Journal article |
| |
Year |
2024 |
Publication |
Chemical engineering and processing |
Abbreviated Journal |
|
|
| |
Volume |
198 |
Issue |
|
Pages |
109715-12 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
This study investigates the distribution of ultrasound (US) energy in a batch system for solutions with viscosity ranging from 1 to approximately 3000 mPas. Sonication was performed using horn type configurations operating at 20-30 kHz and rated power capacity of 50 or 200 W. Two different tip diameters (3 or 7 mm) and two insertion depths (35 or 25 mm) within vessels of different sizes ( approximate to 60 or 130 ml) were utilized. Additionally, a special conical tip design was employed. For each experimental setup, the calorimetric efficiency was estimated, the cavitationally active regions were visualized using the sonochemiluminescence (SCL) method and bubble cluster formation inside the vessel was macroscopically observed using a high speed camera (HSC). In the viscosity range tested, the calorimetry results showed that the efficiency and continuous operation of the device depend on both the rated power and the horn tip diameter. The ratio between electrical and calorimetric power input remained consistently around 40 to 50% across the different configurations for water, but for the 123.2 mPas solution exhibited significant variation ranging from 40 to 85%. Moreover, the power density in the smaller reactor was found to be nearly double compared to the larger one. The SCL analysis showed multiple cavitationally active zones in all setups, and the zones intensity decreased considerably with increase of the solutions viscosity. The results for the cone tip were not conclusive, but can be used as the basis for further investigation. The current research highlights the importance of thoroughly understanding the impact of each design parameter, and of establishing characterization methodologies to assist in the future development of scaled-up, commercial applications. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher  |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001218630800001 |
Publication Date |
2024-02-21 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0255-2701 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
4.3 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 4.3; 2024 IF: 2.234 |
|
| |
Call Number |
UA @ admin @ c:irua:206003 |
Serial |
9154 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Tsonev, I.; Ahmadi Eshtehardi, H.; Delplancke, M.-P.; Bogaerts, A. |
|
| |
Title |
Importance of geometric effects in scaling up energy-efficient plasma-based nitrogen fixation |
Type |
A1 Journal article |
| |
Year |
2024 |
Publication |
Sustainable energy & fuels |
Abbreviated Journal |
|
|
| |
Volume |
|
Issue |
|
Pages |
1-19 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
|
| |
Abstract |
Despite the recent promising potential of plasma-based nitrogen fixation, the technology faces significant challenges in efficient upscaling. To tackle this challenge, we investigate two reactors, i.e., a small one, operating in a flow rate range of 5-20 ln min-1 and current range of 200-500 mA, and a larger one, operating at higher flow rate (100-300 ln min-1) and current (400-1000 mA). Both reactors operate in a pin-to-pin configuration and are powered by direct current (DC) from the same power supply unit, to allow easy comparison and evaluate the effect of upscaling. In the small reactor, we achieve the lowest energy cost (EC) of 2.8 MJ mol-1, for a NOx concentration of 1.72%, at a flow rate of 20 ln min-1, yielding a production rate (PR) of 33 g h-1. These values are obtained in air; in oxygen-enriched air, the results are typically better, at the cost of producing oxygen-enriched air. In the large reactor, the higher flow rates reduce the NOx concentration due to lower SEI, while maintaining a similar EC. This stresses the important effect of the geometrical configuration of the arc, which is typically concentrated in the center of the reactor, resulting in limited coverage of the reacting gas flow, and this is identified as the limiting factor for upscaling. However, our experiments reveal that by changing the reactor configuration, and thus the plasma geometry and power deposition mechanisms, the amount of gas treated by the plasma can be enhanced, leading to successful upscaling. To obtain more insights in our experiments, we performed thermodynamic equilibrium calculations. First of all, they show that our measured lowest EC closely aligns with the calculated minimum thermodynamic equilibrium at atmospheric pressure. In addition, they reveal that the limited NOx production in the large reactor results from the contracted nature of the plasma. To solve this limitation, we let the large reactor operate in so-called torch configuration. Indeed, the latter enhances the NOx concentrations compared to the pin-to-pin configuration, yielding a PR of 80 g h-1 at an EC of 2.9 MJ mol-1 and NOx concentration of 0.31%. This illustrates the importance of reactor design in upscaling. With the focus on feasibility evaluation of scaling-up plasma-based nitrogen fixation by combined experiments and thermodynamic modelling, we aim to tackle the challenge of design and development of an energy-efficient and scaled-up plasma reactor. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001203657700001 |
Publication Date |
2024-04-11 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
|
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ admin @ c:irua:205435 |
Serial |
9155 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Leigh, S.; Doyle, S.J.; Smith, G.J.; Gibson, A.R.; Boswell, R.W.; Charles, C.; Dedrick, J.P. |
|
| |
Title |
Ionization and neutral gas heating efficiency in radio frequency electrothermal microthrusters : the role of driving frequency |
Type |
A1 Journal article |
| |
Year |
2024 |
Publication |
Physics of plasmas |
Abbreviated Journal |
|
|
| |
Volume |
31 |
Issue |
2 |
Pages |
023509-23513 |
|
| |
Keywords |
A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
|
| |
Abstract |
The development of compact, low power, charge-neutral propulsion sources is of significant recent interest due to the rising application of micro-scale satellite platforms. Among such sources, radio frequency (rf) electrothermal microthrusters present an attractive option due to their scalability, reliability, and tunable control of power coupling to the propellant. For micropropulsion applications, where available power is limited, it is of particular importance to understand how electrical power can be transferred to the propellant efficiently, a process that is underpinned by the plasma sheath dynamics. In this work, two-dimensional fluid/Monte Carlo simulations are employed to investigate the effects of applied voltage frequency on the electron, ion, and neutral heating in an rf capacitively coupled plasma microthruster operating in argon. Variations in the electron and argon ion densities and power deposition, and their consequent effect on neutral-gas heating, are investigated with relation to the phase-averaged and phase-resolved sheath dynamics for rf voltage frequencies of 6-108 MHz at 450 V. Driving voltage frequencies above 40.68 MHz exhibit enhanced volumetric ionization from bulk electrons at the expense of the ion heating efficiency. Lower driving voltage frequencies below 13.56 MHz exhibit more efficient ionization due to secondary electrons and an increasing fraction of rf power deposition into ions. Thermal efficiencies are improved by a factor of 2.5 at 6 MHz as compared to the more traditional 13.56 MHz, indicating a favorable operating regime for low power satellite applications. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001207449000001 |
Publication Date |
2024-02-23 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1070-664x |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
2.2 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 2.2; 2024 IF: 2.115 |
|
| |
Call Number |
UA @ admin @ c:irua:205506 |
Serial |
9156 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Vermeulen, B.B.; Monteiro, M.G.; Giuliano, D.; Sorée, B.; Couet, S.; Temst, K.; Nguyen, V.D. |
|
| |
Title |
Magnetization-switching dynamics driven by chiral coupling |
Type |
A1 Journal article |
| |
Year |
2024 |
Publication |
Physical review applied |
Abbreviated Journal |
|
|
| |
Volume |
21 |
Issue |
2 |
Pages |
024050-11 |
|
| |
Keywords |
A1 Journal article; Condensed Matter Theory (CMT) |
|
| |
Abstract |
The Dzyaloshinskii-Moriya interaction (DMI) is known to play a central role in stabilizing chiral spin textures such as skyrmions and domain walls (DWs). Electrical manipulation of DW and skyrmion motion offers possibilities for next-generation, scalable and energy-efficient spintronic devices. However, achieving the full potential of these nanoscale devices requires overcoming several challenges, including reliable electrical write and read techniques for these magnetic objects, and addressing pinning and Joule-heating concerns. Here, through micromagnetic simulations and analytical modeling, we show that DMI can directly induce magnetization switching of a nanomagnet with perpendicular magnetic anisotropy (PMA). We find that the switching is driven by the interplay between the DMI-induced magnetic frustration and the PMA. By introducing magnetic tunnel junctions to electrically access and control the magnetization direction of the PMA nanomagnet, we first show the potential of this concept to enable high-density fieldfree spin-orbit torque magnetic random-access memory. Ultimately, we demonstrate that it offers a way of transferring and processing spin information for logic operation without relying on current-driven DW or skyrmion motion. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001187487900001 |
Publication Date |
2024-02-26 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
2331-7019 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
4.6 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 4.6; 2024 IF: 4.808 |
|
| |
Call Number |
UA @ admin @ c:irua:205518 |
Serial |
9157 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Iungin, O.; Shydlovska, O.; Moshynets, O.; Vasylenko, V.; Sidorenko, M.; Mickevicius, S.; Potters, G. |
|
| |
Title |
Metal-based nanoparticles : an alternative treatment for biofilm infection in hard-to-heal wounds |
Type |
A1 Journal article |
| |
Year |
2024 |
Publication |
Journal of wound care |
Abbreviated Journal |
|
|
| |
Volume |
33 |
Issue |
s:[4A] |
Pages |
99-110 |
|
| |
Keywords |
A1 Journal article; Antwerp engineering, PhotoElectroChemistry & Sensing (A-PECS) |
|
| |
Abstract |
Metal-based nanoparticles (MNPs) are promoted as effective compounds in the treatment of bacterial infections and as possible alternatives to antibiotics. These MNPs are known to affect a broad spectrum of microorganisms using a multitude of strategies, including the induction of reactive oxygen species and interaction with the inner structures of the bacterial cells. The aim of this review was to summarise the latest studies about the effect of metal-based nanoparticles on pathogenic bacterial biofilm formed in wounds, using the examples of Gram-positive bacterium Staphylococcus aureus and Gram-negative bacterium Pseudomonas aeruginosa, as well as provide an overview of possible clinical applications. Declaration of interest: The authors have no conflicts of interest. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001208810700003 |
Publication Date |
2024-04-08 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0969-0700 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
1.9 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 1.9; 2024 IF: 1.446 |
|
| |
Call Number |
UA @ admin @ c:irua:205959 |
Serial |
9159 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Kummamuru, N.B. |
|
| |
Title |
Methane and hydrogen storage in clathrate hydrates |
Type |
Doctoral thesis |
| |
Year |
2024 |
Publication |
|
Abbreviated Journal |
|
|
| |
Volume |
|
Issue |
|
Pages |
XXV, 260 p. |
|
| |
Keywords |
Doctoral thesis; Engineering sciences. Technology; Antwerp engineering, PhotoElectroChemistry & Sensing (A-PECS) |
|
| |
Abstract |
In a world increasingly reliant on alternative energy sources, the quest for efficient and secure storage solutions is paramount. This doctoral thesis explores the exciting potential of a familiar material – water – to act as a vault for next-generation energy sources like hydrogen (H2) and methane (CH4). Nature offers a solution in the form of clathrate hydrates, fascinating cage-like structures formed from water molecules that can trap these gas molecules within their framework. This research investigates on improving the formation kinetics and gas storage capabilities of clathrate hydrates utilizing porous materials and the interstitial space between non-porous materials to augment the contact between gas and water thereby catalysing the growth of hydrates and unlocking their full potential as efficient and secure energy storage reservoirs. A key outcome of this research is the formulation of an empirical correlation, offering predictive insights into CH4 hydrate phase equilibrium conditions. Innovative approaches utilizing thermally conductive beads have yielded substantial enhancements in CH4 uptake. Furthermore, the identification of optimal water content within porous materials showcases a pathway to maximize CH4 storage capacity and hydrate growth kinetics. In the domain of hydrogen storage, attention is also directed towards unstirred systems, where the integration of functionalized porous materials has demonstrated a significant improvement in the rate of hydrate formation and the overall H2 storage capacity. A noteworthy achievement of this research lies in the successful storage of H2 within confined CH4 hydrates through a gas exchange process and the preliminary results show the potential for safer and more sustainable method for H2 storage at mild thermodynamic conditions, offering promising prospects for future energy systems. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
|
Publication Date |
|
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
|
ISBN |
|
Additional Links |
UA library record |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ admin @ c:irua:206258 |
Serial |
9160 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Wang, G.; Xie, C.; Wang, H.; Li, Q.; Xia, F.; Zeng, W.; Peng, H.; Van Tendeloo, G.; Tan, G.; Tian, J.; Wu, J. |
|
| |
Title |
Mitigated oxygen loss in lithium-rich manganese-based cathode enabled by strong Zr-O affinity |
Type |
A1 Journal article |
| |
Year |
2024 |
Publication |
Advanced functional materials |
Abbreviated Journal |
|
|
| |
Volume |
|
Issue |
|
Pages |
2313672 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
Oxygen loss is a serious problem of lithium-rich layered oxide (LLO) cathodes, as the high capacity of LLO relies on reversible oxygen redox. Oxygen release can occur at the surface leading to the formation of spinel or rock salt structures. Also, the lattice oxygen will usually become unstable after long cycling, which remains a major roadblock in the application of LLO. Here, it is shown that Zr doping is an effective strategy to retain lattice oxygen in LLO due to the high affinity between Zr and O. A simple sol-gel method is used to dope Zr4+ into the LLOs to adjust the local electronic structure and inhibit the diffusion of oxygen anions to the surface during cycling. Compared with untreated LLOs, LLO-Zr cathodes exhibit a higher cycling stability, with 94% capacity retention after 100 cycles at 0.4 C, up to 223 mAh g-1 at 1 C, and 88% capacity retention after 300 cycles. Theoretical calculations show that due to the strong Zr-O covalent bonding, the formation energy of oxygen vacancies has effectively increased and the loss of lattice oxygen under high voltage can be suppressed. This study provides a simple method for developing high-capacity and cyclability Li-rich cathode materials for lithium-ion batteries. Oxygen release can occur at the cathode surface leading to the formation of spinel or rock salt structures. Here, it is shown that Zr doping is an effective strategy to retain lattice oxygen in lithium-rich layered oxides (LLO) due to the high affinity between Zr and O. LLO-Zr exhibit higher cycling stability, with 88% capacity retention after 300 cycles at 1 C. image |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001159843800001 |
Publication Date |
2024-02-10 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1616-301x |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
19 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 19; 2024 IF: 12.124 |
|
| |
Call Number |
UA @ admin @ c:irua:203812 |
Serial |
9161 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Coulombier, M.; Baral, P.; Orekhov, A.; Dohmen, R.; Raskin, J.P.; Pardoen, T.; Cordier, P.; Idrissi, H. |
|
| |
Title |
On-chip very low strain rate rheology of amorphous olivine films |
Type |
A1 Journal article |
| |
Year |
2024 |
Publication |
Acta materialia |
Abbreviated Journal |
|
|
| |
Volume |
266 |
Issue |
|
Pages |
119693-12 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
Recent observations made by the authors revealed the activation of stress induced amorphization and sliding at grain boundary in olivine [1], a mechanism which is expected to play a pivotal role in the viscosity drop at the lithosphere-asthenosphere boundary and the brittle -ductile transition in the lithospheric mantle. However, there is a lack of information in the literature regarding the intrinsic mechanical properties and the elementary deformation mechanisms of this material, especially at time scales relevant for geodynamics. In the present work, amorphous olivine films were obtained by pulsed laser deposition (PLD). The mechanical response including the rate dependent behavior are investigated using a tension -on -chip (TOC) method developed at UCLouvain allowing to perform creep/relaxation tests on thin films at extremely low strain rates. In the present work, strain rate down to 10-12 s- 1 was reached which is unique. High strain rate sensitivity of 0.054 is observed together with the activation of relaxation at the very early stage of deformation. Furthermore, digital image correlation (DIC), used for the first time on films deformed by TOC, reveals local strain heterogeneities. The relationship between such heterogeneities, the high strain rate sensitivity and the effect of the electron beam in the scanning electron microscope is discussed and compared to the literature. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001170513400001 |
Publication Date |
2024-01-17 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1359-6454 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
9.4 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 9.4; 2024 IF: 5.301 |
|
| |
Call Number |
UA @ admin @ c:irua:204864 |
Serial |
9163 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Joy, R.M.; Pobedinskas, P.; Bourgeois, E.; Chakraborty, T.; Goerlitz, J.; Herrmann, D.; Noel, C.; Heupel, J.; Jannis, D.; Gauquelin, N.; D'Haen, J.; Verbeeck, J.; Popov, C.; Houssiau, L.; Becher, C.; Nesladek, M.; Haenen, K. |
|
| |
Title |
Photoluminescence of germanium-vacancy centers in nanocrystalline diamond films : implications for quantum sensing applications |
Type |
A1 Journal article |
| |
Year |
2024 |
Publication |
ACS applied nano materials |
Abbreviated Journal |
|
|
| |
Volume |
7 |
Issue |
4 |
Pages |
3873-3884 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
Point defects in diamond, promising candidates for nanoscale pressure- and temperature-sensing applications, are potentially scalable in polycrystalline diamond fabricated using the microwave plasma-enhanced chemical vapor deposition (MW PE CVD) technique. However, this approach introduces residual stress in the diamond films, leading to variations in the characteristic zero phonon line (ZPL) of the point defect in diamond. Here, we report the effect of residual stress on germanium-vacancy (GeV) centers in MW PE CVD nanocrystalline diamond (NCD) films fabricated using single crystal Ge as the substrate and solid dopant source. GeV ensemble formation indicated by the zero phonon line (ZPL) at similar to 602 nm is confirmed by room temperature (RT) photoluminescence (PL) measurements. PL mapping results show spatial nonuniformity in GeV formation along with other defects, including silicon-vacancy centers in the diamond films. The residual stress in NCD results in shifts in the PL peak positions. By estimating a stress shift coefficient of (2.9 +/- 0.9) nm/GPa, the GeV PL peak position in the NCD film is determined to be between 598.7 and 603.2 nm. A larger ground state splitting due to the strain on a GeV-incorporated NCD pillar at a low temperature (10 K) is also reported. We also report the observation of intense ZPLs at RT that in some cases could be related to low Ge concentration and the surrounding crystalline environment. In addition, we also observe thicker microcrystalline diamond (MCD) films delaminate from the Ge substrate due to film residual stress and graphitic phase at the diamond/Ge substrate interface (confirmed by electron energy loss spectroscopy). Using this approach, a free-standing color center incorporated MCD film with dimensions up to 1 x 1 cm(2) is fabricated. Qualitative analysis using time-of-flight secondary ion mass spectroscopy reveals the presence of impurities, including Ge and silicon, in the MCD film. Our experimental results will provide insights into the scalability of GeV fabrication using the MW PE CVD technique and effectively implement NCD-based nanoscale-sensing applications. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001164609600001 |
Publication Date |
2024-02-15 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
2574-0970 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
5.9 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 5.9; 2024 IF: NA |
|
| |
Call Number |
UA @ admin @ c:irua:204826 |
Serial |
9164 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Fang, W.; Wang, X.; Li, S.; Hao, Y.; Yang, Y.; Zhao, W.; Liu, R.; Li, D.; Li, C.; Gao, X.; Wang, L.; Guo, H.; Yi, Y. |
|
| |
Title |
Plasma-catalytic one-step steam reforming of CH₄ to CH₃OH and H₂ promoted by oligomerized [Cu-O-Cu] species on zeolites |
Type |
A1 Journal article |
| |
Year |
2024 |
Publication |
Green chemistry : cutting-edge research for a greener sustainable future |
Abbreviated Journal |
|
|
| |
Volume |
26 |
Issue |
9 |
Pages |
5150-5154 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
|
| |
Abstract |
Oligomerized [Cu-O-Cu] species are reported to be efficient in promoting plasma catalytic one-step steam reforming of methane to methanol and hydrogen, achieving 6.8% CH4 conversion and 73.1% CH3OH selectivity without CO2. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001195192800001 |
Publication Date |
2024-04-02 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1463-9262; 1463-9270 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
9.8 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 9.8; 2024 IF: 9.125 |
|
| |
Call Number |
UA @ admin @ c:irua:205514 |
Serial |
9165 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Long, Y.; Wang, X.; Zhang, H.; Wang, K.; Ong, W.-L.; Bogaerts, A.; Li, K.; Lu, C.; Li, X.; Yan, J.; Tu, X.; Zhang, H. |
|
| |
Title |
Plasma chemical looping : unlocking high-efficiency CO₂ conversion to clean CO at mild temperatures |
Type |
A1 Journal article |
| |
Year |
2024 |
Publication |
JACS Au |
Abbreviated Journal |
|
|
| |
Volume |
|
Issue |
|
Pages |
|
|
| |
Keywords |
A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
|
| |
Abstract |
We propose a plasma chemical looping CO2 splitting (PCLCS) approach that enables highly efficient CO2 conversion into O-2-free CO at mild temperatures. PCLCS achieves an impressive 84% CO2 conversion and a 1.3 mmol g(-1) CO yield, with no O-2 detected. Crucially, this strategy significantly lowers the temperature required for conventional chemical looping processes from 650 to 1000 degrees C to only 320 degrees C, demonstrating a robust synergy between plasma and the Ce0.7Zr0.3O2 oxygen carrier (OC). Systematic experiments and density functional theory (DFT) calculations unveil the pivotal role of plasma in activating and partially decomposing CO2, yielding a mixture of CO, O-2/O, and electronically/vibrationally excited CO2*. Notably, these excited CO2* species then efficiently decompose over the oxygen vacancies of the OCs, with a substantially reduced activation barrier (0.86 eV) compared to ground-state CO2 (1.63 eV), contributing to the synergy. This work offers a promising and energy-efficient pathway for producing O-2-free CO from inert CO2 through the tailored interplay of plasma and OCs. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001225139200001 |
Publication Date |
2024-05-08 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
|
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ admin @ c:irua:205970 |
Serial |
9166 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Lu, Q. |
|
| |
Title |
Precipitation behavior and heat resistance properties of Al-Cu-Mg-Ag-(Si) alloy |
Type |
Doctoral thesis |
| |
Year |
2024 |
Publication |
|
Abbreviated Journal |
|
|
| |
Volume |
|
Issue |
|
Pages |
VIII, 212 p. |
|
| |
Keywords |
Doctoral thesis; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
With the rapid increase in the speed of new-generation aerospace vehicles, conventional heat-resistant aluminum alloys cannot meet the long-term service of the equipment. Therefore, the development of new high-strength heat-resistant aluminum alloys is of great strategic for the sustainable and high-quality development of industries. Al-Cu-Mg-Ag alloy is an age-hardenable heat-resistant aluminum alloy and has high strength and heat resistance. The addition of alloying elements such as Si and Sc to Al-Cu-Mg-Ag alloy introduces a competitive relationship among the σ-Al5Cu6Mg2, θ′-Al2Cu, and Ω phases. Therefore, a systematic investigation of precipitation behavior and heat resistance of Al-Cu-Mg-Ag-(Si) is essential for guiding the design of high-strength heat-resistant aluminum alloys. Combined characterization testing methods such as scanning electron microscopy, transmission electron microscopy, atom probe tomography, microhardness testing, and tensile testing with simulation calculation methods such as calculation of phase diagram, first-principles calculations, and Ab initio molecular dynamics, the effects of heat treatment processes and element content on the precipitation behavior, mechanical properties, and heat resistance of Al-Cu-Mg-Ag-(Si) alloys were systematically investigated. Furthermore, a multiple interface segregation structure was constructed at the θ′/Al interface, and a new Al-Cu-Mg-Ag-Si-Sc alloy with synergistically improved strength and heat resistance was developed. The main conclusions are as follows: (1) Based on the Kampmann-Wagner-Numerical theory, the relationship between the coarsening rate of the Ω phase and the aging process was analyzed, revealing for the first time that the critical size of Ω phase ( ) under thermal exposure temperature was the key factor determining the coarsening rate of Ω phase during long time thermal exposure heat treatment. After artificial ageing, when the size of Ω phase was smaller than the critical size , the dissolution of smaller Ω phase leaded to a rapid decrease in the number density of Ω phases, thereby reducing the heat resistance of the alloy. When the size of Ω phase was greater than or equal to the critical size , the coarsening rate of Ω phase was consistent, but a larger initial size would result in a larger final size after long-term thermal exposure. Therefore, the closer the size of Ω phase in the alloy is to the critical size under heat exposure temperature, the better the heat resistance of the alloy. (2) A concept of constructing a multiple interface segregation structure at the precipitate/matrix interface was proposed, and based on this concept, a multiple interface segregation structure containing the C/L-AlMgSiCu interfacial phase, newly discovered χ-AgMg interfacial phase, and Sc segregation layer was successfully constructed at the θ′/Al interface. The existence of the multiple interface segregation structure ensured that the designed Al-Cu-Mg-Ag-Si-Sc alloy maintains a yield strength of 400 MPa after thermal exposure at 200 C for 100 h, with a strength retention rate of 97%, creating a new record for the synergistic improvement of strength and heat resistance in aluminum alloys. In addition, combining transmission electron microscopy ex-situ/in-situ characterization with first-principles calculations, it is shown that the χ-AgMg interface phase will be destroyed due to the diffusion of the outer Ag layer during thermal exposure, and gradually dissolve into the matrix, but it can still delay the coarsening behavior of θ′-Al2Cu phase. (3) The criteria for determining whether Ω phase can precipitate are updated in Al-Cu-Mg-Ag-Si alloys with low Mg/Si ratio based on phase diagram thermodynamic calculations and multi-scale structural characterization. When W(Mg)/W(Si) > 1.4 and X(Ag)/X(Mgexcess) > 1, Ω phase can precipitate in Al-Cu-Mg-Ag-Si alloys, where X(Mgexcess) represents the atomic percentage of residual Mg elements after the formation of the AlMgSiCu quaternary precipitate phase C/L phase in the supersaturated solid solution, and the W(Mg) is the mass fraction of Mg in the supersaturated solid solution before artificial ageing. (4) The effects of alloy element content on precipitation behavior and heat resistance of Al-Cu-Mg-Ag-Si alloys were systematically analyzed. Critical conditions for the precipitation of σ-Al5Cu6Mg2 and Ω phase in Al-Cu-Mg-Ag-Si alloys are revealed. Based on calculation of phase diagram results, the conditions for precipitating σ-Al5Cu6Mg2 phase in the alloy are: ① W(Mg)/W(Si) > 1.8; ② W(Cu) > 2.7W(Mg) – 5W(Si). When W(Mg)/W(Si) < 1.8, the alloy is mainly precipitated with C/L/Q′-AlMgSiCu. When W(Cu) < 2.7W(Mg) – 5W(Si), the alloy will generate GPB zone. In addition, W(Ag)/W(Si) > 4 is the critical condition which the Ω phase can the main precipitates in Al-Cu-Mg-Ag-Si alloys. Furthermore, the correlation between precipitate types and heat resistance was summarized, showing that Al-Cu-Mg-Ag-(Si) alloys with Ω phase as the main strengthening phase are more suitable for the preparation of structures with short service time but high temperature, while Al-Cu-Mg-Ag-(Si) alloys with low Mg content and multiple segregation structures are more suitable for structures requiring long-term service at medium to high temperatures. This study, for the first time, combines calculation of phase diagram with multi-scale microstructure characterization, systematically unraveling the effects of element content on precipitation behavior, strength, and heat resistance of Al-Cu-Mg-Ag-(Si) alloys. In addition, a concept of constructing a multiple interface segregation structure at the precipitate/matrix interface was proposed to synergistically improve alloy strength and heat resistance. This work provides theoretical guidance for optimizing the composition and processing of Al-Cu-Mg-Ag-(Si) alloy and regulating the microstructure. Furthermore, it also offers new ideas and theoretical guidance for the development of novel high-strength heat-resistant alloys in other systems. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
|
Publication Date |
|
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
|
ISBN |
|
Additional Links |
UA library record |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ admin @ c:irua:206180 |
Serial |
9167 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Tiwari, S.; Van de Put, M.; Sorée, B.; Hinkle, C.; Vandenberghe, W.G. |
|
| |
Title |
Reduction of magnetic interaction due to clustering in doped transition-metal dichalcogenides : a case study of Mn-, V-, and Fe-doped WSe₂ |
Type |
A1 Journal article |
| |
Year |
2024 |
Publication |
ACS applied materials and interfaces |
Abbreviated Journal |
|
|
| |
Volume |
16 |
Issue |
4 |
Pages |
4991-4998 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT) |
|
| |
Abstract |
Using Hubbard-U-corrected density functional theory calculations, lattice Monte Carlo simulations, and spin Monte Carlo simulations, we investigate the impact of dopant clustering on the magnetic properties of WSe2 doped with period four transition metals. We use manganese (Mn) and iron (Fe) as candidate n-type dopants and vanadium (V) as the candidate p-type dopant, substituting the tungsten (W) atom in WSe2. Specifically, we determine the strength of the exchange interaction in Fe-, Mn-, and V-doped WSe2 in the presence of clustering. We show that the clusters of dopants are energetically more stable than discretely doped systems. Further, we show that in the presence of dopant clustering, the magnetic exchange interaction significantly reduces because the magnetic order in clustered WSe2 becomes more itinerant. Finally, we show that the clustering of the dopant atoms has a detrimental effect on the magnetic interaction, and to obtain an optimal Curie temperature, it is important to control the distribution of the dopant atoms. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001155511900001 |
Publication Date |
2024-01-18 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1944-8244 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
9.5 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 9.5; 2024 IF: 7.504 |
|
| |
Call Number |
UA @ admin @ c:irua:203830 |
Serial |
9169 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Poppe, R.; Roth, N.; Neder, R.B.; Palatinus, L.; Iversen, B.B.; Hadermann, J. |
|
| |
Title |
Refining short-range order parameters from the three-dimensional diffuse scattering in single-crystal electron diffraction data |
Type |
A1 Journal article |
| |
Year |
2024 |
Publication |
IUCrJ |
Abbreviated Journal |
|
|
| |
Volume |
11 |
Issue |
1 |
Pages |
82-91 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
Our study compares short-range order parameters refined from the diffuse scattering in single-crystal X-ray and single-crystal electron diffraction data. Nb0.84CoSb was chosen as a reference material. The correlations between neighbouring vacancies and the displacements of Sb and Co atoms were refined from the diffuse scattering using a Monte Carlo refinement in DISCUS. The difference between the Sb and Co displacements refined from the diffuse scattering and the Sb and Co displacements refined from the Bragg reflections in single-crystal X-ray diffraction data is 0.012 (7) angstrom for the refinement on diffuse scattering in single-crystal X-ray diffraction data and 0.03 (2) angstrom for the refinement on the diffuse scattering in single-crystal electron diffraction data. As electron diffraction requires much smaller crystals than X-ray diffraction, this opens up the possibility of refining short-range order parameters in many technologically relevant materials for which no crystals large enough for single-crystal X-ray diffraction are available. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001168018300012 |
Publication Date |
2023-12-14 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
2052-2525 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
3.9 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 3.9; 2024 IF: 5.793 |
|
| |
Call Number |
UA @ admin @ c:irua:205513 |
Serial |
9170 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Sethu, K.K.V.; Yasin, F.; Swerts, J.; Sorée, B.; De Boeck, J.; Kar, G.S.; Garello, K.; Couet, S. |
|
| |
Title |
Spin-orbit torque vector quantification in nanoscale magnetic tunnel junctions |
Type |
A1 Journal article |
| |
Year |
2024 |
Publication |
ACS nano |
Abbreviated Journal |
|
|
| |
Volume |
18 |
Issue |
21 |
Pages |
13506-13516 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT) |
|
| |
Abstract |
Spin-orbit torques (SOT) allow ultrafast, energy-efficient toggling of magnetization state by an in-plane charge current for applications such as magnetic random-access memory (SOT-MRAM). Tailoring the SOT vector comprising of antidamping (T-AD) and fieldlike (T-FL) torques could lead to faster, more reliable, and low-power SOT-MRAM. Here, we establish a method to quantify the longitudinal (T-AD) and transverse (T-FL) components of the SOT vector and its efficiency chi(AD) and chi(FL), respectively, in nanoscale three-terminal SOT magnetic tunnel junctions (SOT-MTJ). Modulation of nucleation or switching field (B-SF) for magnetization reversal by SOT effective fields (B-SOT) leads to the modification of SOT-MTJ hysteresis loop behavior from which chi(AD) and chi(FL) are quantified. Surprisingly, in nanoscale W/CoFeB SOT-MTJ, we find chi(FL) to be (i) twice as large as chi(AD) and (ii) 6 times as large as chi(FL) in micrometer-sized W/CoFeB Hall-bar devices. Our quantification is supported by micromagnetic and macrospin simulations which reproduce experimental SOT-MTJ Stoner-Wohlfarth astroid behavior only for chi(FL) > chi(AD). Additionally, from the threshold current for current-induced magnetization switching with a transverse magnetic field, we show that in SOT-MTJ, T-FL plays a more prominent role in magnetization dynamics than T-AD. Due to SOT-MRAM geometry and nanodimensionality, the potential role of nonlocal spin Hall spin current accumulated adjacent to the SOT-MTJ in the mediation of T-FL and chi(FL) amplification merits to be explored. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001226121700001 |
Publication Date |
2024-05-15 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1936-0851 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
17.1 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 17.1; 2024 IF: 13.942 |
|
| |
Call Number |
UA @ admin @ c:irua:205980 |
Serial |
9173 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Manaigo, F. |
|
| |
Title |
Study of a gliding arc discharge for sustainable nitrogen fixation into NOx |
Type |
Doctoral thesis |
| |
Year |
2024 |
Publication |
|
Abbreviated Journal |
|
|
| |
Volume |
|
Issue |
|
Pages |
xxiv, 114 p. |
|
| |
Keywords |
Doctoral thesis; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
|
| |
Abstract |
With the growth of the world population, the agricultural sector is required to meet an increasing demand for nutrients and currently relies on industrially produced fertilizers. Among them, nitrogen-based fertilizers are the most common choice and require N2 to be converted into more reactive molecules in a process called “nitrogen fixation”. This is mainly performed through the Haber-Bosch process, which, is not ideal since it requires large-scale facilities to be economical and is associated with a high energy cost and high CO2 emissions, resulting in an environmental impact that is pushing for the study of greener alternatives. Among these, plasma-based nitrogen fixation into NOx is promising, and gliding arc plasma, specifically, proved to be suitable for nitrogen fixation. This thesis aims to study plasma-based nitrogen fixation focusing on an atmospheric pressure gliding arc plasma on three different levels. On a fundamental level, an approach dealing with laser-based excitation of separate rotational lines was successfully developed. This method can be implemented on atmospheric discharges that produce rather high NOx densities and, thus, can impose essential restrictions for the use of “classical” laser-induced fluorescence methods. The approach is then implemented, providing a discussion on the two-dimensional distributions of both the gas temperature and the NO ground state density. A clear correlation between these quantities is found and the effects of both the gas temperature and the plasma power on NO and NO2 concentrations are discussed, revealing how the NO oxidation is already significant in the plasma afterglow region and how the gas flow rate is a crucial parameter affecting the temperature gradients. >From a technological level, the conventional approach of introducing external resistors to stabilize the arc is challenged by studying both its performance and its stability replacing the external resistor with an inductor. We conclude that similar stabilization results can be obtained while significantly lowering the overall energy cost, which decreased from up to a maximum of 7.9 MJ/mol N to 3 MJ/mol N. Finally, we study whether a small-scale fertilizer production facility based on a gliding arc plasma can be a local competitive alternative. This is done by proposing a comparative model to understand how capital, operative expenditures and transport costs affect the production costs. The model highlights how, with the current best available technology, plasma-based nitrogen fixation, while being an interesting alternative for NOx synthesis, still requires a more efficient use of H2 for direct NH3 production. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
|
Publication Date |
|
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
|
ISBN |
|
Additional Links |
UA library record |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ admin @ c:irua:205259 |
Serial |
9175 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Brognara, A.; Kashiwar, A.; Jung, C.; Zhang, X.; Ahmadian, A.; Gauquelin, N.; Verbeeck, J.; Djemia, P.; Faurie, D.; Dehm, G.; Idrissi, H.; Best, J.P.; Ghidelli, M. |
|
| |
Title |
Tailoring mechanical properties and shear band propagation in ZrCu metallic glass nanolaminates through chemical heterogeneities and interface density |
Type |
A1 Journal article |
| |
Year |
2024 |
Publication |
Small Structures |
Abbreviated Journal |
|
|
| |
Volume |
|
Issue |
|
Pages |
2400011-11 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
The design of high‐performance structural thin films consistently seeks to achieve a delicate equilibrium by balancing outstanding mechanical properties like yield strength, ductility, and substrate adhesion, which are often mutually exclusive. Metallic glasses (MGs) with their amorphous structure have superior strength, but usually poor ductility with catastrophic failure induced by shear bands (SBs) formation. Herein, we introduce an innovative approach by synthesizing MGs characterized by large and tunable mechanical properties, pioneering a nanoengineering design based on the control of nanoscale chemical/structural heterogeneities. This is realized through a simplified model Zr 24 Cu 76 /Zr 61 Cu 39 , fully amorphous nanocomposite with controlled nanoscale periodicity ( Λ , from 400 down to 5 nm), local chemistry, and glass–glass interfaces, while focusing in‐depth on the SB nucleation/propagation processes. The nanolaminates enable a fine control of the mechanical properties, and an onset of crack formation/percolation (>1.9 and 3.3%, respectively) far above the monolithic counterparts. Moreover, we show that SB propagation induces large chemical intermixing, enabling a brittle‐to‐ductile transition when Λ ≤ 50 nm, reaching remarkably large plastic deformation of 16% in compression and yield strength ≈2 GPa. Overall, the nanoengineered control of local heterogeneities leads to ultimate and tunable mechanical properties opening up a new approach for strong and ductile materials. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
|
Publication Date |
2024-05-20 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
2688-4062 |
ISBN |
|
Additional Links |
UA library record |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ admin @ c:irua:205798 |
Serial |
9176 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Chai, Z.-N.; Wang, X.-C.; Yusupov, M.; Zhang, Y.-T. |
|
| |
Title |
Unveiling the interaction mechanisms of cold atmospheric plasma and amino acids by machine learning |
Type |
A1 Journal article |
| |
Year |
2024 |
Publication |
Plasma processes and polymers |
Abbreviated Journal |
|
|
| |
Volume |
|
Issue |
|
Pages |
1-26 |
|
| |
Keywords |
A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
|
| |
Abstract |
Plasma medicine has attracted tremendous interest in a variety of medical conditions, ranging from wound healing to antimicrobial applications, even in cancer treatment, through the interactions of cold atmospheric plasma (CAP) and various biological tissues directly or indirectly. The underlying mechanisms of CAP treatment are still poorly understood although the oxidative effects of CAP with amino acids, peptides, and proteins have been explored experimentally. In this study, machine learning (ML) technology is introduced to efficiently unveil the interaction mechanisms of amino acids and reactive oxygen species (ROS) in seconds based on the data obtained from the reactive molecular dynamics (MD) simulations, which are performed to probe the interaction of five types of amino acids with various ROS on the timescale of hundreds of picoseconds but with the huge computational load of several days. The oxidative reactions typically start with H-abstraction, and the details of the breaking and formation of chemical bonds are revealed; the modification types, such as nitrosylation, hydroxylation, and carbonylation, can be observed. The dose effects of ROS are also investigated by varying the number of ROS in the simulation box, indicating agreement with the experimental observation. To overcome the limits of timescales and the size of molecular systems in reactive MD simulations, a deep neural network (DNN) with five hidden layers is constructed according to the reaction data and employed to predict the type of oxidative modification and the probability of occurrence only in seconds as the dose of ROS varies. The well-trained DNN can effectively and accurately predict the oxidative processes and productions, which greatly improves the computational efficiency by almost ten orders of magnitude compared with the reactive MD simulation. This study shows the great potential of ML technology to efficiently unveil the underpinning mechanisms in plasma medicine based on the data from reactive MD simulations or experimental measurements. In this study, since reactive molecular dynamics simulation can currently only describe interactions between a few hundred atoms in a few hundred picoseconds, deep neural networks (DNN) are introduced to enhance the simulation results by predicting more data efficiently. image |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001202061200001 |
Publication Date |
2024-04-15 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1612-8850 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
3.5 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 3.5; 2024 IF: 2.846 |
|
| |
Call Number |
UA @ admin @ c:irua:205512 |
Serial |
9181 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
O'Modhrain, C.; Trenchev, G.; Gorbanev, Y.; Bogaerts, A. |
|
| |
Title |
Upscaling plasma-based CO₂ conversion : case study of a multi-reactor gliding arc plasmatron |
Type |
A1 Journal article |
| |
Year |
2024 |
Publication |
ACS Engineering Au |
Abbreviated Journal |
|
|
| |
Volume |
|
Issue |
|
Pages |
|
|
| |
Keywords |
A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
|
| |
Abstract |
Atmospheric pressure plasmas have shifted in recent years from being a burgeoning research field in the academic setting to an actively investigated technology in the chemical, oil, and environmental industries. This is largely driven by the climate change mitigation efforts, as well as the evident pathways of value creation by converting greenhouse gases (such as CO2) into useful chemical feedstock. Currently, most high technology readiness level (TRL) plasma-based technologies are based on volumetric and power-based scaling of thermal plasma systems, which results in large capital investment and regular maintenance costs. This work investigates bringing a quasi-thermal (so-called “warm”) plasma setup, namely, a gliding arc plasmatron, from a lab-scale to a pilot-scale capacity with an increase in throughput capacity by a factor of 10. The method of scaling is the parallelization of plasmatron reactors within a single housing, with the aim of maintaining a warm plasma regime while simultaneously improving build cost and efficiency (compared to separate reactors operating in parallel). Special attention is also given to the safety and control features implemented in the setup, a key component required for integration into industrial systems. The performance of the multi-reactor gliding arc plasmatron (MRGAP) reactor is investigated, focusing on the influence of flow rate and the number of active reactors. The location of active reactors was deemed to have a negligible effect on the monitored metrics of conversion, energy efficiency, and energy cost. The optimum operating conditions were found to be with the most active reactors (five) at the highest investigated flow rate (80 L/min). Analysis of results suggests that an optimum conversion (9%) and plug power-based energy efficiency (19%) can be maintained at a specific energy input (SEI) around 5.3 kJ/L (or 1 eV/molecule). The concept of parallelization of plasmatron reactors within a singular housing was demonstrated to be a viable method for scaling up from a lab-scale to a prototype-scale device, with performance analysis suggesting that increasing the power (through adding more reactor channels) and total flow rate, while maintaining an SEI around 5.3 or 4.2 kJ/L, i.e., 1.3 or 1 eV/molecule (based on plug power and plasma-deposited power, respectively), can result in increased conversion rate without sacrificing absolute conversion or energy efficiency. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001166625200001 |
Publication Date |
2024-02-14 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
|
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ admin @ c:irua:204749 |
Serial |
9182 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Verbruggen, L.; Verheggen, L.; Vanhoutte, G.; Loly, C.; Lybaert, W.; Borbath, I.; Vergauwe, P.; Hendrickx, K.; Debeuckelaere, C.; de Haar-Holleman, A.; Van Laethem, J.-L.; Peeters, M. |
|
| |
Title |
A real-world analysis on the efficacy and tolerability of liposomal irinotecan plus 5-fluorouracil and folinic acid in metastatic pancreatic ductal adenocarcinoma in Belgium |
Type |
A1 Journal article |
| |
Year |
2023 |
Publication |
Therapeutic advances in medical oncology |
Abbreviated Journal |
|
|
| |
Volume |
15 |
Issue |
|
Pages |
1-13 |
|
| |
Keywords |
A1 Journal article; Center for Oncological Research (CORE) |
|
| |
Abstract |
Background: Currently, nanoliposomal irinotecan (nal-IRI) + 5-fluorouracil/folinic acid (5-FU/ LV) is the only approved second-line treatment for patients suffering from metastatic pancreatic ductal adenocarcinoma (mPDAC). However, also other chemotherapeutic regimens are used in this setting and due to the lack of clear real-world data on the efficacy of the different regimens, there is no consensus on the optimal treatment sequence for mPDAC patients. Objectives: To provide information on the safe and efficacious use of nal-IRI + 5-FU/LV in clinical practice in Belgium, which is needed for healthcare professionals to estimate the risk-benefit ratio of the intervention. Methods: Medical data of adult patients with mPDAC who were treated with nal-IRI + 5-FU/ LV in one of the participating Belgian hospitals were retrospectively collected. Kaplan-Meier analysis was performed to obtain survival curves to estimate the median overall survival (OS) and progression-free survival (PFS). All other results were presented descriptively. Results: A total of 56 patients [median age at diagnosis: 69 years (range 43 years), 57.1% male] were included. Patients received a median of 5 (range 49 cycles) nal-IRI + 5-FU/LV cycles, extended over 10 weeks (range 130.8 weeks). The median start dose for nal-IRI was 70 mg/ m(2) (range 49.24 mg/m(2)) and chemotherapy dose reduction and delay occurred in, respectively, 42.8% and 37.5% of the patients. The median OS was 6.8 months (95% CI: 5.6-8.4 months) with a 6-month survival rate of 57.4% and a 1-year survival rate of 27.8% in the overall study population. The median OS for patients treated with nal-IRI as second-line therapy or as laterline treatment was, respectively, 6.8 months (95% CI: 5.9-7.0 months) and 5.6 months (95% CI: 4.2-no upper limit). In the overall study population, a median PFS of 3.1 months (95% CI: 2.4-4.6 months) and a disease control rate of 48.3%, comprising 30.4% stable disease, 16.1% partial and 1.8% complete response, was observed. The median PFS for patients treated with nal-IRI as second-line therapy was 3.9 months (95% CI: 2.8-4.8 months) while this was 2.4 months (95% CI: 1.9-9.1 months) for those that received nal-IRI in a later-line treatment. In terms of safety, gastrointestinal problems occurred most (64.3% of the patients) and from all reported treatment emergent adverse events, 39.2% were grade 3 or 4. Conclusion: Nal-IRI + 5-FU/LV is a valuable, effective, and safe sequential treatment option following gemcitabine-based therapy in patients with mPDAC. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001051446400001 |
Publication Date |
2023-08-18 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1758-8340; 1758-8359 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
4.9 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 4.9; 2023 IF: 6.294 |
|
| |
Call Number |
UA @ admin @ c:irua:199296 |
Serial |
9183 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Fabri, C.; Tsagris, M.; Moretti, M.; Van Passel, S. |
|
| |
Title |
Adaptation to climate change : the irrigation technology mix of Italian farmers |
Type |
A1 Journal article |
| |
Year |
2023 |
Publication |
Applied economic perspectives and policy |
Abbreviated Journal |
|
|
| |
Volume |
|
Issue |
|
Pages |
1-22 |
|
| |
Keywords |
A1 Journal article; Economics; Engineering Management (ENM) |
|
| |
Abstract |
Farmers should increasingly adopt more water‐efficient irrigation technologies—such as drip irrigation—as a result of climate warming and aggravating water scarcity. We analyze how Italian farmers adapt to climate change by changing their irrigation technology mix. We apply a two‐stage econometric model to data from 5876 Italian farms. We find that farmers' initial reaction to increasing temperatures is reducing their surface‐irrigated fractions. When temperatures increase further, farmers switch toward more sprinkler irrigation. Our results show that farmers are not autonomously moving to drip irrigation in response to climate change, suggesting that government incentives are needed to encourage this transition. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001125360800001 |
Publication Date |
2023-12-16 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
2040-5790 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
5.8 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 5.8; 2023 IF: 1.361 |
|
| |
Call Number |
UA @ admin @ c:irua:201688 |
Serial |
9184 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Teleshkan, E.; Van Schoubroeck, S.; Spiller, M.; Van Passel, S. |
|
| |
Title |
Assessing policy impacts on nutrient circularity : a comprehensive review |
Type |
A1 Journal article |
| |
Year |
2024 |
Publication |
Nutrient cycling in agroecosystems |
Abbreviated Journal |
|
|
| |
Volume |
|
Issue |
|
Pages |
1-15 |
|
| |
Keywords |
A1 Journal article; Economics; Engineering sciences. Technology; Engineering Management (ENM) |
|
| |
Abstract |
Nutrient circularity is an emerging concept that seeks to address the environmental problems and nutrient losses caused by agriculture and food consumption. The implementation of circular nutrient technologies and practices (CNTPs), that recover, reuse, and recycle nutrients from agricultural and urban waste is an important policy objective. Yet, which policies govern the adoption of CNTPs is not well defined. This study presents the first systematic review of impact evaluations of policy measures that aim to improve nutrient circularity regulating components of the biological cycle of the circular economy, particularly focusing on bioaccessible nutrients. The key CNTPs that were subject to existing impact evaluations were identified. CNTPs were categorized into nutrient circularity themes, with manure management emerging as a prominent focus. The reviewed studies implemented several methods to assess the impacts of policies on various dependent variables, associated with nutrient circularity. Economic simulation models and linear programming were the most prevalent methods for impact evaluation. Policy measures were labeled as either enabling or not-enabling nutrient circularity based on whether they sufficiently promoted nutrient circularity through facilitating the adoption of CNTPs, and controlling for soil, water and air health, preventing its contamination. It is concluded that incentive policies, harmonizing market support, tax incentives, and technological advancements, as well as coherence of local, national and cross-country legislation prove indispensable in steering the economic feasibility and sustainability of CNTPs, offering a promising avenue for progress and a transformative shift towards nutrient circularity. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001175764500001 |
Publication Date |
2024-02-29 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1385-1314; 1573-0867 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
3.1 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 3.1; 2024 IF: 1.843 |
|
| |
Call Number |
UA @ admin @ c:irua:204250 |
Serial |
9185 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Vasilakou, K.; Nimmegeers, P.; Thomassen, G.; Billen, P.; Van Passel, S. |
|
| |
Title |
Assessing the future of second-generation bioethanol by 2030 : a techno-economic assessment integrating technology learning curves |
Type |
A1 Journal article |
| |
Year |
2023 |
Publication |
Applied energy |
Abbreviated Journal |
|
|
| |
Volume |
344 |
Issue |
|
Pages |
121263-15 |
|
| |
Keywords |
A1 Journal article; Economics; Engineering sciences. Technology; Engineering Management (ENM); Intelligence in PRocesses, Advanced Catalysts and Solvents (iPRACS) |
|
| |
Abstract |
Lignocellulosic biomass is the most abundant source of renewable biomass and is seen as a high-potential replacement for petroleum-based resources. The conversion technologies to advanced biofuels are still at a low maturity level, thus allowing for future cost reductions through technological learning. This fact is barely considered in state-of-the-art techno-economic assessments and a structured approach to account for technological learning in techno-economic assessments is needed. In this study, a framework for techno-economic assessments of advanced biofuels, integrating learning curves, is proposed. As a validation of this framework, the economic feasibility of the valorization of corn stover for the production of second-generation bioethanol in Belgium is studied. Process flowsheet simulations in Aspen Plus are developed, with an emphasis on the comparison of four different pretreatment technologies and two plant capacities at 156 dry kt biomass/y and 667 dry kt/y. The dilute acid pretreatment model of the large-scale biorefinery required the lowest minimum learning rate to reach an economically feasible biorefinery by 2030, being 3.9%, almost half as the one calculated for the smaller scale plant. This learning rate seems to be achievable based on learning rates commonly estimated in literature. We conclude that there is a potential for advanced ethanol production in Belgium under the current state of technology for large-scale biorefineries, which require additional biomass imports, when accounting for future cost reductions through learning |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001007488700001 |
Publication Date |
2023-05-22 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0306-2619 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
11.2 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 11.2; 2023 IF: 7.182 |
|
| |
Call Number |
UA @ admin @ c:irua:196509 |
Serial |
9186 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Verbruggen, S.; Van Acker, M.; Furlan, C.; Mercelis, S.; Durt, A. |
|
| |
Title |
ATLANTES : the mATeriaL spAtial dimeNsion of wasTE flowS: visualising waste streams in the Province of Antwerp |
Type |
Minutes and reports |
| |
Year |
2023 |
Publication |
|
Abbreviated Journal |
|
|
| |
Volume |
|
Issue |
|
Pages |
|
|
| |
Keywords |
Minutes and reports; Economics; Engineering sciences. Technology; Internet Data Lab (IDLab); Research Group for Urban Development; Henry van de Velde |
|
| |
Abstract |
|
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
|
Publication Date |
|
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
|
ISBN |
|
Additional Links |
UA library record |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ admin @ c:irua:199837 |
Serial |
9187 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Reynaert, S.; Vienne, A.; de Boeck, H.J.; D'Hose, T.; Janssens, I.; Nijs, I.; Portillo-Estrada, M.; Verbruggen, E.; Vicca, S. |
|
| |
Title |
Basalt addition improves the performance of young grassland monocultures under more persistent weather featuring longer dry and wet spells |
Type |
A1 Journal article |
| |
Year |
2023 |
Publication |
Agricultural and forest meteorology |
Abbreviated Journal |
|
|
| |
Volume |
340 |
Issue |
1 |
Pages |
109610 |
|
| |
Keywords |
A1 Journal article; Plant and Ecosystems (PLECO) – Ecology in a time of change |
|
| |
Abstract |
Global warming is altering the intra-annual variability of precipitation patterns in the mid-latitudes, including a shift towards longer dry and wet spells compared to historic averages. Such fluctuations will likely alter soil water and nutrient dynamics of managed ecosystems which could negatively influence their functioning (e.g., productivity and fodder quality). Here, we investigated whether basalt addition could attenuate effects of increasingly persistent precipitation regimes (PR) on two agricultural grassland monocultures differing in drought resistance (low: Lolium perenne (LP) vs high: Festulolium (FL)) and digestibility (high: LP, low: FL), while improving soil C sequestration. In total, 32 experimental mesocosms were subjected to either a low (1-day wet/ dry alternation) or a highly (30-day wet/dry alternation) persistent PR over 120 days, keeping total precipitation equal. In half of these mesocosms, we mixed basalt with the top 20 cm soil layer at a rate of 50 t ha-1. Overall, 30-day PR increased average water availability resulting in improved aboveground biomass and shoot digestibility for both species, in spite of elevated physiological stress. These PR also increased shoot Si, K, N and C but reduced Ca accumulation. Basalt addition generally increased soil Al, Ni, Mg, Ca, P, K and Si availability without altering root biomass or total soil carbon. Moreover, differences in root N content and C:N ratio between species were reduced. Interestingly, basalt modified the PR effects on productivity. Within 30-day PR, basalt stimulated aboveground biomass (& PLUSMN;14%) and root Si and K contents without altering plant digestibility, palatability, crude protein content or Ni/Al content. These results indicate that basalt can stimulate grassland productivity and soil nutrient availability under more persistent PR without negatively affecting fodder quality. Hence, basalt application may improve the performance of young temperate grassland monocultures under climate change, though dry soil conditions may limit effects on soil C sequestration during summer. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001051084500001 |
Publication Date |
2023-07-21 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0168-1923 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
6.2 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 6.2; 2023 IF: 3.887 |
|
| |
Call Number |
UA @ admin @ c:irua:199204 |
Serial |
9189 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Zi, L.; Reynaert, S.; Nijs, I.; De Boeck, H.; Verbruggen, E.; Beemster, G.T.S.; Asard, H.; Abdelgawad, H. |
|
| |
Title |
Biochemical composition changes can be linked to the tolerance of four grassland species under more persistent precipitation regimes |
Type |
A1 Journal article |
| |
Year |
2023 |
Publication |
Physiologia plantarum |
Abbreviated Journal |
|
|
| |
Volume |
175 |
Issue |
6 |
Pages |
e14083-13 |
|
| |
Keywords |
A1 Journal article; Integrated Molecular Plant Physiology Research (IMPRES); Plant and Ecosystems (PLECO) – Ecology in a time of change |
|
| |
Abstract |
Climate models suggest that the persistence of summer precipitation regimes (PRs) is on the rise, characterized by both longer dry and longer wet durations. These PR changes may alter plant biochemical composition and thereby their economic and ecological characteristics. However, impacts of PR persistence have primarily been studied at the community level, largely ignoring the biochemistry of individual species. Here, we analyzed biochemical components of four grassland species with varying sensitivity to PR persistence (Holcus lanatus, Phleum pratense, Lychnis flos-cuculi, Plantago lanceolata) along a range of increasingly persistent PRs (longer consecutive dry and wet periods) in a mesocosm experiment. The more persistent PRs decreased nonstructural sugars, whereas they increased lignin in all species, possibly reducing plant quality. The most sensitive species Lychnis seemed less capable of altering its biochemical composition in response to altered PRs, which may partly explain its higher sensitivity. The more tolerant species may have a more robust and dynamic biochemical network, which buffers the effects of changes in individual biochemical components on biomass. We conclude that the biochemical composition changes are important determinants for plant performance under increasingly persistent precipitation regimes. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001108556200001 |
Publication Date |
2023-11-25 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0031-9317 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
6.4 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 6.4; 2023 IF: 3.33 |
|
| |
Call Number |
UA @ admin @ c:irua:202003 |
Serial |
9190 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Reynaert, S.; D’Hose, T.; de Boeck, H.J.; Laorden, D.; Dult, L.; Verbruggen, E.; Nijs, I. |
|
| |
Title |
Can permanent grassland soils with elevated organic carbon buffer negative effects of more persistent precipitation regimes on forage grass performance? |
Type |
A1 Journal article |
| |
Year |
2024 |
Publication |
The science of the total environment |
Abbreviated Journal |
|
|
| |
Volume |
918 |
Issue |
|
Pages |
170623-15 |
|
| |
Keywords |
A1 Journal article; Plant and Ecosystems (PLECO) – Ecology in a time of change |
|
| |
Abstract |
Agricultural practices enhancing soil organic carbon (SOC) show potential to buffer negative effects of climate change on forage grass performance. We tested this by subjecting five forage grass varieties differing in fodder quality and drought/flooding resistance to increased persistence in summer precipitation regimes (PR) across sandy and sandy-loam soils from either permanent (high SOC) or temporary grasslands (low SOC) in adjacent parcels. Over the course of two consecutive summers, monoculture mesocosms were subjected to rainy/dry weather alternation either every 3 days or every 30 days, whilst keeping total precipitation equal. Increased PR persistence induced species-specific drought damage and productivity declines. Soils from permanent grasslands with elevated SOC buffered plant quality, but buffering effects of SOC on drought damage, nutrient availability and yield differed between texture classes. In the more persistent PR, Festuca arundinacea FERMINA was the most productive species but had the lowest quality under both ample water supply and mild soil drought, whilst under the most intense soil droughts, Festulolium FESTILO maintained the highest yields. The hybrid Lolium × boucheanum kunth MELCOMBI had intermediate productivity and both Lolium perenne varieties showed the lowest yields under soil drought, but the highest forage quality (especially the tetraploid variety MELFORCE). Performance varied with plant maturity stage and across seasons/years and was driven by altered water and nutrient availability and related nitrogen nutrition among species during drought and upon rewetting. Moreover, whilst permanent grassland soils showed the most consistent positive effects on plant performance, their available water capacity also declined under increased PR persistence. We conclude that permanent grassland soils with historically elevated SOC likely buffer negative effects of increasing summer weather persistence on forage grass performance, but may also be more sensitive to degradation under climate change. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001183615800001 |
Publication Date |
2024-02-04 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0048-9697; 1879-1026 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
9.8 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 9.8; 2024 IF: 4.9 |
|
| |
Call Number |
UA @ admin @ c:irua:204498 |
Serial |
9191 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Van Hoecke, L. |
|
| |
Title |
CFD-Assisted design of fluidized reactors for H2 release from LOHC |
Type |
Doctoral thesis |
| |
Year |
2024 |
Publication |
|
Abbreviated Journal |
|
|
| |
Volume |
|
Issue |
|
Pages |
XXXIII, 181 p. |
|
| |
Keywords |
Doctoral thesis; Engineering sciences. Technology |
|
| |
Abstract |
Hydrogen (H2) is expected to become a key molecule in the transition towards a society running on renewable energy. It can be used to store excess renewable energy at peak production moments and release this energy at a later stage when renewable energy production is less. However, storing H2 is challenging due to the low density of this gas. As a solution, Liquid Organic Hydrogen Carriers or LOHC molecules have been proposed in the passed to increase volumetric energy density of H2. LOHC are a class of molecules that have storage sites available, to which the H2 gas can be chemically bounded. The LOHC molecule under investigation was dibenzyltoluene (DBT), which is an oil like liquid, that is easy to transport and poses little fire or explosion risks. To release the H2 from the DBT carrier, via a so-called dehydrogenation reaction, efficient mass and heat transfer is required during the process, since a large volume increase is expected from H2 release and the reaction is endothermic, i.e., a self – cooling process that takes place at temperatures around 300 C. The heat has to be supplied specifically to the active sites of catalyst particles that are present inside the reactor and which enable the dehydrogenation to proceed. For heat transfer limited processes fluidized bed reactors are often used, which is a type of reactor where the particle phase is being agitated by the fluid flow. The research proposed in this work, was to explore via computational fluid dynamics (CFD) simulations the possibilities and challenges of using fluidized bed reactors for the dehydrogenation of LOHC. The model selection required for CFD simulations of a three-phase system was investigated in this work, with a main emphasis on the drag model selection. The CFD modelling study was focused on the use of swirling fluidized bed reactors, since it was hypothesised that the swirling effect could also aid in increased removal of the gas phase from the reaction medium to increase the efficiency of the process. Ultimately, it was shown that the main challenges in the design of fluidized bed reactors will be to create uniform particle distribution inside the reactor. A new design for a dehydrogenation reactor is proposed based on the insights gained in this thesis. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
|
Publication Date |
2024-06-14 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
|
ISBN |
|
Additional Links |
UA library record |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ admin @ c:irua:205645 |
Serial |
9192 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Deleu, N.; Hillen, M.; Steenackers, G.; Borms, G.; Janssens, K.; Van der Stighelen, K.; Van der Snickt, G. |
|
| |
Title |
Combined macro X-ray fluorescence (MA-XRF) and pulse phase thermography (PPT) imaging for the technical study of panel paintings |
Type |
A1 Journal article |
| |
Year |
2024 |
Publication |
Talanta : the international journal of pure and applied analytical chemistry |
Abbreviated Journal |
|
|
| |
Volume |
270 |
Issue |
|
Pages |
125533-11 |
|
| |
Keywords |
A1 Journal article; Art; Antwerp Cultural Heritage Sciences (ARCHES); Antwerp X-ray Imaging and Spectroscopy (AXIS) |
|
| |
Abstract |
Museum staff usually relies on a proven combination of X-ray radiography (XRR) and infrared reflectography (IRR) to study paintings in a non-destructive manner. In the last decades, however, the research toolbox of heritage scientists has expanded considerably, with a prime example being macro X-ray fluorescence (MA-XRF), producing element-specific images. The goal of this article is to illustrate the added value of augmenting MA-XRF with pulse phase thermography (PPT), a variant of active infrared thermographic imaging (IRT), which is an innovative diagnostic method that is able to reveal variations between or in materials, based on a different response to minor fluctuations in temperature when irradiated with optical radiation. By examining three 16thand 17th-century panel paintings we assess the extent in which combined MA-XRF and PPT contributes to a better understanding of two commonly encountered interventions to panel paintings: (a) Anstuckungen (enlargement of the panel) or (b) substitutions (replacement of part of the panel). Yielding information from different depths of the painting, these two techniques proved highly complementary with IRR and XRR, expanding the understanding of the build-up, genesis, and material history of the paintings. While MA-XRF documented the interventions to the wooden substrate indirectly by revealing variations in painting materials, paint handling and/ or layer sequence between the original part and the extended or replaced planks, PPT proved beneficial for the study of the wooden support itself, by providing a clear image of the wood structure quasi-free of distortion by the superimposed paint or cradling. XRR, on the other hand, revealed other features from the wood structure, not visible with PPT, and allowed looking through the wooden panels, revealing e.g. the dowels used for joining the planks. Additionally, IRR visualised dissimilarities in the underdrawings. In this way, the results indicate that PPT has the potential to become an acknowledged add-on to the expanding set of imaging methods for paintings, especially when used in combination with MA-XRF, IRR and XRR. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001144098200001 |
Publication Date |
2023-12-09 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0039-9140; 1873-3573 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
6.1 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 6.1; 2024 IF: 4.162 |
|
| |
Call Number |
UA @ admin @ c:irua:203764 |
Serial |
9193 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Radujković, D.; Vicca, S.; van Rooyen, M.; Wilfahrt, P.; Brown, L.; Jentsch, A.; Reinhart, K.O.; Brown, C.; De Gruyter, J.; Jurasinski, G.; Askarizadeh, D.; Bartha, S.; Beck, R.; Blenkinsopp, T.; Cahill, J.; Campetella, G.; Canullo, R.; Chelli, S.; Enrico, L.; Fraser, L.; Hao, X.; Henry, H.A.L.; Hohn, M.; Jouri, M.H.; Koch, M.; Lawrence Lodge, R.; Li, F.Y.; Lord, J.M.; Milligan, P.; Minggagud, H.; Palmer, T.; Schröder, B.; Szabó, G.; Zhang, T.; Zimmermann, Z.; Verbruggen, E. |
|
| |
Title |
Consistent predictors of microbial community composition across spatial scales in grasslands reveal low context‐dependency |
Type |
A1 Journal article |
| |
Year |
2023 |
Publication |
Molecular ecology |
Abbreviated Journal |
|
|
| |
Volume |
32 |
Issue |
24 |
Pages |
6924-6938 |
|
| |
Keywords |
A1 Journal article; Plant and Ecosystems (PLECO) – Ecology in a time of change |
|
| |
Abstract |
Environmental circumstances shaping soil microbial communities have been studied extensively. However, due to disparate study designs, it has been difficult to resolve whether a globally consistent set of predictors exists, or context‐dependency prevails. Here, we used a network of 18 grassland sites (11 of those containing regional plant productivity gradients) to examine (i) if similar abiotic or biotic factors predict both large‐scale (across sites) and regional‐scale (within sites) patterns in bacterial and fungal community composition, and (ii) if microbial community composition differs consistently at two levels of regional plant productivity (low vs. high). Our results revealed that bacteria were associated with particular soil properties (such as base saturation) and both bacteria and fungi were associated with plant community composition across sites and within the majority of sites. Moreover, a discernible microbial community signal emerged, clearly distinguishing high and low‐productivity soils across different grasslands independent of their location in the world. Hence, regional productivity differences may be typified by characteristic soil microbial communities across the grassland biome. These results could encourage future research aiming to predict the general effects of global changes on soil microbial community composition in grasslands and to discriminate fertile from infertile systems using generally applicable microbial indicators. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001090315100001 |
Publication Date |
2023-10-24 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0962-1083 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
4.9 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 4.9; 2023 IF: 6.086 |
|
| |
Call Number |
UA @ admin @ c:irua:200464 |
Serial |
9194 |
|
| Permanent link to this record |
