| Home | << 1 2 3 4 5 6 7 8 9 10 11 12 13 >> |
|
| Records | |||||
|---|---|---|---|---|---|
| Author | Belov, I.; Paulussen, S.; Bogaerts, A. | ||||
| Title | Appearance of a conductive carbonaceous coating in a CO2dielectric barrier discharge and its influence on the electrical properties and the conversion efficiency | Type | A1 Journal article | ||
| Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 015023 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | This work examines the properties of a dielectric barrier discharge (DBD) reactor, built for CO2 decomposition, by means of electrical characterization, optical emission spectroscopy and gas chromatography. The discharge, formed in an electronegative gas (such as CO2, but also O2), exhibits clearly different electrical characteristics, depending on the surface conductivity of the reactor walls. An asymmetric current waveform is observed in the metaldielectric (MD) configuration, with sparse high-current pulses in the positive half-cycle (HC) and a more uniform regime in the negative HC. This indicates that the discharge is operating in two alternating regimes with rather different properties. At high CO2 conversion regimes, a conductive coating is deposited on the dielectric. This so-called coated MD configuration yields a symmetric current waveform, with current peaks in both the positive and negative HCs. In a double-dielectric (DD) configuration, the current waveform is also symmetric, but without current peaks in both the positive and negative HC. Finally, the DD configuration with conductive coating on the inner surface of the outer dielectric, i.e. so-called coated DD, yields again an asymmetric current waveform, with current peaks in the negative HC. These different electrical characteristics are related to the presence of the conductive coating on the dielectric wall of the reactor and can be explained by an increase of the local barrier capacitance available for charge transfer. The different discharge regimes affect the CO2 conversion, more specifically, the CO2 conversion is lowest in the clean DD configuration. It is somewhat higher in the coated DD configuration, and still higher in the MD configuration. The clean and coated MD configuration, however, gave similar CO2 conversion. These results indicate that the conductivity of the dielectric reactor walls can highly promote the development of the high-amplitude discharge current pulses and subsequently the CO2 conversion. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication  |
Editor | |||
| Language | Wos | 000370974800030 | Publication Date | 2016-01-21 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 25 | Open Access | |
| Notes | The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7-PEOPLE-2013-ITN) under Grant Agreement № 606889 (RAPID—Reactive Atmospheric Plasma processIng—eDucation network). | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:130790 | Serial | 4006 | ||
| Permanent link to this record | |||||
| Author | Ozkan, A.; Dufour, T.; Silva, T.; Britun, N.; Snyders, R.; Bogaerts, A.; Reniers, F. | ||||
| Title | The influence of power and frequency on the filamentary behavior of a flowing DBD—application to the splitting of CO2 | Type | A1 Journal article | ||
| Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 025013 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | In this experimental study, a flowing dielectric barrier discharge operating at atmospheric pressure is used for the splitting of CO2 into O2 and CO. The influence of the applied frequency and plasma power on the microdischarge properties is investigated to understand their role on the CO2 conversion. Electrical measurements are carried out to explain the conversion trends and to characterize the microdischarges through their number, their lifetime, their intensity and the induced electrical charge. Their influence on the gas and electrode temperatures is also evidenced through optical emission spectroscopy and infrared imaging. It is shown that, in our configuration, the conversion depends mostly on the charge delivered in the plasma and not on the effective plasma voltage when the applied power is modified. Similarly, at constant total current, a better conversion is observed at low frequencies, where a less filamentary discharge regime with a higher effective plasma voltage than that at a higher frequency is obtained. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000372337900015 | Publication Date | 2016-02-25 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 40 | Open Access | |
| Notes | The authors acknowledge financial support from the IAPVII/ 12, P7/34 (Inter-university Attraction Pole) program ‘PSI-Physical Chemistry of Plasma-Surface Interactions’, financially supported by the Belgian Federal Office for Science Policy (BELSPO). A Ozkan would like to thank the financial support given by ‘Fonds David et Alice Van Buuren’. N Britun is a postdoctoral researcher of the F.R.S.-FNRS, Belgium. | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:131904 | Serial | 4021 | ||
| Permanent link to this record | |||||
| Author | Milovanovic, S.P.; Peeters, F.M. | ||||
| Title | Characterization of the size and position of electron-hole puddles at a graphene p-n junction | Type | A1 Journal article | ||
| Year | 2016 | Publication | Nanotechnology | Abbreviated Journal | Nanotechnology |
| Volume | 27 | Issue | 27 | Pages | 105203 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT) | ||||
| Abstract | The effect of an electron-hole puddle on the electrical transport when governed by snake states in a bipolar graphene structure is investigated. Using numerical simulations we show that information on the size and position of the electron-hole puddle can be obtained using the dependence of the conductance on magnetic field and electron density of the gated region. The presence of the scatterer disrupts snake state transport which alters the conduction pattern. We obtain a simple analytical formula that connects the position of the electron-hole puddle with features observed in the conductance. The size of the electron-hole puddle is estimated from the magnetic field and gate potential that maximizes the effect of the puddle on the electrical transport. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | English | Wos | 000369849200003 | Publication Date | 2016-02-11 |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0957-4484 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.44 | Times cited | 3 | Open Access | |
| Notes | This work was supported by the Flemish Science Foundation (FWO-Vl) and the European Science Foundation (ESF) under the EUROCORES Program EuroGRAPHENE within the project CONGRAN. We acknowledge interesting correspondence with Thiti Taychatanapat. | Approved | Most recent IF: 3.44 | ||
| Call Number | c:irua:131907 | Serial | 4025 | ||
| Permanent link to this record | |||||
| Author | Filez, M.; Redekop, E.A.; Poelman, H.; Galvita, V.V.; Meledina, M.; Turner, S.; Van Tendeloo, G.; Detavernier, C.; Marin, G.B. | ||||
| Title | One-pot synthesis of Pt catalysts based on layered double hydroxides: an application in propane dehydrogenation | Type | A1 Journal article | ||
| Year | 2016 | Publication | Catalysis science & technology | Abbreviated Journal | Catal Sci Technol |
| Volume | 6 | Issue | 6 | Pages | 1863-1869 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Simple methods for producing noble metal catalysts with well-defined active sites and improved performance are highly desired in the chemical industry. However, the development of such methods still presents a formidable synthetic challenge. Here, we demonstrate a one-pot synthesis route for the controlled production of bimetallic Pt–In catalysts based on the single-step formation of Mg,Al,Pt,In-containing layered double hydroxides (LDHs). Besides their simple synthesis, these Pt–In catalysts exhibit superior propane dehydrogenation activity compared to their multi-step synthesized analogs. The presented material serves as a showcase for the one-pot synthesis of a broader class of LDH-derived mono- and multimetallic Pt catalysts. The compositional flexibility provided by LDH materials can pave the way towards highperforming Pt-based catalysts with tunable physicochemical properties. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000372172800031 | Publication Date | 2015-10-23 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2044-4753 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 5.773 | Times cited | 12 | Open Access | |
| Notes | This work was supported by the Fund for Scientific Research Flanders (FWO: G.0209.11), the ‘Long Term Structural Methusalem Funding by the Flemish Government’, the IAP 7/05 Interuniversity Attraction Poles Programme – Belgian State – Belgian Science Policy, and the Fund for Scientific Research Flanders (FWO-Vlaanderen) by supplying financing of beam time at the DUBBLE beamline of the ESRF and travel costs and a post-doctoral fellowship for S. T. The authors acknowledge the assistance from the DUBBLE (XAS campaign 26-01-979) and SuperXAS staff (Proposal 20131191). E. A. Redekop acknowledges the Marie Curie International Incoming Fellowship granted by the European Commission (Grant Agreement No. 301703). The authors also express their gratitude to O. Janssens for performing ex situ XRD characterization. | Approved | Most recent IF: 5.773 | ||
| Call Number | c:irua:133167 | Serial | 4057 | ||
| Permanent link to this record | |||||
| Author | Trenchev, G.; Kolev, S.; Bogaerts, A. | ||||
| Title | A 3D model of a reverse vortex flow gliding arc reactor | Type | A1 Journal article | ||
| Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 035014 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | In this computational study, a gliding arc plasma reactor with a reverse-vortex flow stabilization is modelled for the first time by a fluid plasma description. The plasma reactor operates with argon gas at atmospheric pressure. The gas flow is simulated using the k-ε Reynolds-averaged Navier–Stokes turbulent model. A quasi-neutral fluid plasma model is used for computing the plasma properties. The plasma arc movement in the reactor is observed, and the results for the gas flow, electrical characteristics, plasma density, electron temperature, and gas temperature are analyzed. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000376557400022 | Publication Date | 2016-04-09 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 20 | Open Access | |
| Notes | This research was carried out in the framework of the network on Physical Chemistry of Plasma–Surface Interactions— Interuniversity Attraction Poles, phase VII (http://psi-iap7.ulb. ac.be/), and supported by the Belgian Science Policy Office (BELSPO), and it was also funded by the Fund for Scientific Research Flanders (FWO). Grant number: 11U5316N. | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:132888 c:irua:132888 | Serial | 4063 | ||
| Permanent link to this record | |||||
| Author | Ozkan, A.; Dufour, T.; Bogaerts, A.; Reniers, F. | ||||
| Title | How do the barrier thickness and dielectric material influence the filamentary mode and CO2conversion in a flowing DBD? | Type | A1 Journal article | ||
| Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 045016 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Dielectric barrier discharges (DBDs) are commonly used to generate cold plasmas at atmospheric pressure. Whatever their configuration (tubular or planar), the presence of a dielectric barrier is mandatory to prevent too much charge build up in the plasma and the formation of a thermal arc. In this article, the role of the barrier thickness (2.0, 2.4 and 2.8 mm) and of the kind of dielectric material (alumina, mullite, pyrex, quartz) is investigated on the filamentary behavior in the plasma and on the CO2 conversion in a tubular flowing DBD, by means of mass spectrometry measurements correlated with electrical characterization and IR imaging. Increasing the barrier thickness decreases the capacitance, while preserving the electrical charge. As a result, the voltage over the dielectric increases and a larger number of microdischarges is generated, which enhances the CO2 conversion. Furthermore, changing the dielectric material of the barrier, while keeping the same geometry and dimensions, also affects the CO2 conversion. The highest CO2 conversion and energy efficiency are obtained for quartz and alumina, thus not following the trend of the relative permittivity. From the electrical characterization, we clearly demonstrate that the most important parameters are the somewhat higher effective plasma voltage (yielding a somewhat higher electric field and electron energy in the plasma) for quartz, as well as the higher plasma current (and thus larger electron density) and the larger number of microdischarge filaments (mainly for alumina, but also for quartz). The latter could be correlated to the higher surface roughness for alumina and to the higher voltage over the dielectric for quartz. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000380380200030 | Publication Date | 2016-06-30 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 24 | Open Access | |
| Notes | The authors acknowledge financial support from the IAPVII/ 12, P7/34 (Inter-university Attraction Pole) program ‘PSI-Physical Chemistry of Plasma-Surface Interactions’, financially supported by the Belgian Federal Office for Science Policy (BELSPO). A. Ozkan would like to thank the financial support given by ‘Fonds David et Alice Van Buuren’. | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:134396 | Serial | 4100 | ||
| Permanent link to this record | |||||
| Author | Berthelot, A.; Bogaerts, A. | ||||
| Title | Modeling of plasma-based CO2conversion: lumping of the vibrational levels | Type | A1 Journal article | ||
| Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 045022 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Although CO2 conversion by plasma technology is gaining increasing interest, the underlying mechanisms for an energy-efficient process are still far from understood. In this work, a reduced non-equilibrium CO2 plasma chemistry set, based on level lumping of the vibrational levels, is proposed and the reliability of this level-lumping method is tested by a self-consistent zero-dimensional code. A severe reduction of the number of equations to be solved is achieved, which is crucial to be able to model non-equilibrium CO2 plasmas by 2-dimensional models. Typical conditions of pressure and power used in a microwave plasma for CO2 conversion are investigated. Several different sets, using different numbers of lumped groups, are considered. The lumped models with 1, 2 or 3 groups are able to reproduce the gas temperature, electron density and electron temperature profiles, as calculated by the full model treating all individual excited levels, in the entire pressure range investigated. Furthermore, a 3-groups model is also able to reproduce the shape of the vibrational distribution function (VDF) and gives the most reliable prediction of the CO2 conversion. A strong influence of the vibrational excitation on the plasma characteristics is observed. Finally, the limitations of the lumped-levels method are discussed. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000380380200036 | Publication Date | 2016-07-08 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 33 | Open Access | |
| Notes | This project has received funding from the European Union’s Seventh Framework Programme for research, technological development and demonstration under grant agreement no 606889 and it was also carried out in the framework of the network on Physical Chemistry of Plasma-Surface Interactions—Interuniversity Attraction Poles, phase VII (PSI-IAP7) supported by the Belgian Science Policy Office (BELSPO). The computational work was carried out using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UA), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UA. | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:134397 | Serial | 4101 | ||
| Permanent link to this record | |||||
| Author | Ozkan, A.; Dufour, T.; Silva, T.; Britun, N.; Snyders, R.; Reniers, F.; Bogaerts, A. | ||||
| Title | DBD in burst mode: solution for more efficient CO2conversion? | Type | A1 Journal article | ||
| Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 055005 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | CO2 conversion into value-added products has gained significant interest over the few last years, as the greenhouse gas concentrations constantly increase due to anthropogenic activities. Here we report on experiments for CO2 conversion by means of a cold atmospheric plasma using a cylindrical flowing dielectric barrier discharge (DBD) reactor. A detailed comparison of this DBD ignited in a so-called burst mode (i.e. where an AC voltage is applied during a limited amount of time) and pure AC mode is carried out to evaluate their effect on the conversion of CO2 as well as on the energy efficiency. Decreasing the duty cycle in the burst mode from 100% (i.e. corresponding to pure AC mode) to 40% leads to a rise in the conversion from 16–26% and to a rise in the energy efficiency from 15 to 23%. Based on a detailed electrical analysis, we show that the conversion correlates with the features of the microfilaments. Moreover, the root-mean-square voltage in the burst mode remains constant as a function of the process time for the duty cycles <70%, while a higher duty cycle or the usual pure AC mode leads to a clear voltage decay by more than 500 V, over approximately 90 s, before reaching a steady state regime. The higher plasma voltage in the burst mode yields a higher electric field. This causes the increasing the electron energy, and therefore their involvement in the CO2 dissociation process, which is an additional explanation for the higher CO2 conversion and energy efficiency in the burst mode. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000403945500005 | Publication Date | 2016-08-02 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 17 | Open Access | |
| Notes | The authors acknowledge financial support from the IAPVII/ 12, P7/34 (Inter-university Attraction Pole) program ‘PSI-Physical Chemistry of Plasma-Surface Interactions’, financially supported by the Belgian Federal Office for Science Policy (BELSPO). A. Ozkan would also like to thank financial support given by ‘Fonds David et Alice Van Buuren’. | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:134841 | Serial | 4107 | ||
| Permanent link to this record | |||||
| Author | Bogaerts, A.; Wang, W.; Berthelot, A.; Guerra, V. | ||||
| Title | Modeling plasma-based CO2conversion: crucial role of the dissociation cross section | Type | A1 Journal article | ||
| Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 055016 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Plasma-based CO2 conversion is gaining increasing interest worldwide. A large research effort is devoted to improving the energy efficiency. For this purpose, it is very important to understand the underlying mechanisms of the CO2 conversion. The latter can be obtained by computer modeling, describing in detail the behavior of the various plasma species and all relevant chemical processes. However, the accuracy of the modeling results critically depends on the accuracy of the assumed input data, like cross sections. This is especially true for the cross section of electron impact dissociation, as the latter process is believed to proceed through electron impact excitation, but it is not clear from the literature which excitation channels effectively lead to dissociation. Therefore, the present paper discusses the effect of different electron impact dissociation cross sections reported in the literature on the calculated CO2 conversion, for a dielectric barrier discharge (DBD) and a microwave (MW) plasma. Comparison is made to experimental data for the DBD case, to elucidate which cross section might be the most realistic. This comparison reveals that the cross sections proposed by Itikawa and by Polak and Slovetsky both seem to underestimate the CO2 conversion. The cross sections recommended by Phelps with thresholds of 7 eV and 10.5 eV yield a CO2 conversion only slightly lower than the experimental data, but the sum of both cross sections overestimates the values, indicating that these cross sections represent dissociation, but most probably also include other (pure excitation) channels. Our calculations indicate that the choice of the electron impact dissociation cross section is crucial for the DBD, where this process is the dominant mechanism for CO2 conversion. In the MW plasma, it is only significant at pressures up to 100 mbar, while it is of minor importance for higher pressures, when dissociation proceeds mainly through collisions of CO2 with heavy particles. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000384030600001 | Publication Date | 2016-08-31 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 57 | Open Access | |
| Notes | The authors would like to thank R Snoeckx and S Heijkers for the interesting discussions. This research was supported by the European Union’s Seventh Framework Programme for research, technological development and demonstration under grant agreement no. 606889, the European Marie Skłodowska-Curie Individual Fellowship project ‘GlidArc’ within Horizon2020, the FWO project (grant G.0383.16N), and the Network on Physical Chemistry of Plasma-Surface Interactions—Interuniversity Attraction Poles, phase VII (PSI-IAP7), supported by the Belgian Science Policy Office (BELSPO). The computational work was carried out using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UA), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UA. VG was partially supported by the Portuguese FCT— Fundação para a Ci | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:135070 | Serial | 4111 | ||
| Permanent link to this record | |||||
| Author | Spadaro, M.C.; Luches, P.; Bertoni, G.; Grillo, V.; Turner, S.; Van Tendeloo, G.; Valeri, S.; D'Addato, S. | ||||
| Title | Influence of defect distribution on the reducibility of CeO2-x nanoparticles | Type | A1 Journal article | ||
| Year | 2016 | Publication | Nanotechnology | Abbreviated Journal | Nanotechnology |
| Volume | 27 | Issue | 27 | Pages | 425705 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Ceria nanoparticles (NPs) are fundamental in heterogeneous catalysis because of their ability to store or release oxygen depending on the ambient conditions. Their oxygen storage capacity is strictly related to the exposed planes, crystallinity, density and distribution of defects. In this work a study of ceria NPs produced with a ligand-free, physical synthesis method is presented. The NP films were grown by a magnetron sputtering based gas aggregation source and studied by high resolution- and scanning-transmission electron microscopy and x-ray photoelectron spectroscopy. In particular, the influence of the oxidation procedure on the NP reducibility has been investigated. The different reducibility has been correlated to the exposed planes, crystallinity and density and distribution of structural defects. The results obtained in this work represent a basis to obtain cerium oxide NP with desired oxygen transport properties. | ||||
| Address | Dipartimento FIM, Universita di Modena e Reggio Emilia, via G. Campi 213/a, I-41125 Modena, Italy. CNR-NANO, via G. Campi 213/a, I-41125 Modena, Italy | ||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | English | Wos | 000385483900004 | Publication Date | 2016-09-15 |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0957-4484 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.44 | Times cited | 11 | Open Access | |
| Notes | The authors gratefully acknowledge financial support by the Italian MIUR under grant FIRB RBAP115AYN (Oxides at the nanoscale: multifunctionality and applications). The activity is performed within the COST Action CM1104 'Reducible oxide chemistry, structure and functions'. The research leading to these results has received funding also from the European Union Seventh Framework Programme under Grant Agreement 312483—ESTEEM2 (Integrated Infrastructure Initiative–I3).; esteem2_ta | Approved | Most recent IF: 3.44 | ||
| Call Number | EMAT @ emat @ c:irua:135424 | Serial | 4130 | ||
| Permanent link to this record | |||||
| Author | Wang, W.; Bogaerts, A. | ||||
| Title | Effective ionisation coefficients and critical breakdown electric field of CO2at elevated temperature: effect of excited states and ion kinetics | Type | A1 Journal article | ||
| Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 055025 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Electrical breakdown by the application of an electric field occurs more easily in hot gases than in cold gases because of the extra electron-species interactions that occur as a result of dissociation, ionization and excitation at higher temperature. This paper discusses some overlooked physics and clarifies inaccuracies in the evaluation of the effective ionization coefficients and the critical reduced breakdown electric field of CO2 at elevated temperature, considering the influence of excited states and ion kinetics. The critical reduced breakdown electric field is obtained by balancing electron generation and loss mechanisms using the electron energy distribution function (EEDF) derived from the Boltzmann transport equation under the two-term approximation. The equilibrium compositions of the hot gas mixtures are determined based on Gibbs free energy minimization considering the ground states as well as vibrationally and electronically excited states as independent species, which follow a Boltzmann distribution with a fixed excitation temperature. The interaction cross sections between electrons and the excited species, not reported previously, are properly taken into account. Furthermore, the ion kinetics, including electron–ion recombination, associative electron detachment, charge transfer and ion conversion into stable negative ion clusters, are also considered. Our results indicate that the excited species lead to a greater population of high-energy electrons at higher gas temperature and this affects the Townsend rate coefficients (i.e. of electron impact ionization and attachment), but the critical reduced breakdown electric field strength of CO2 is only affected when also properly accounting for the ion kinetics. Indeed, the latter greatly influences the effective ionization coefficients and hence the critical reduced breakdown electric field at temperatures above 1500 K. The rapid increase of the dissociative electron attachment cross-section of molecular oxygen with rising vibrational quantum number leads to a larger electron loss rate and this enhances the critical reduced breakdown electric field strength in the temperature range where the concentration of molecular oxygen is relatively high. The results obtained in this work show reasonable agreement with experimental results from literature, and are important for the evaluation of the dielectric strength of CO2 in a highly reactive environment at elevated temperature. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000385494000006 | Publication Date | 2016-09-22 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 3 | Open Access | |
| Notes | Skłodowska-Curie Individual Fellowship ‘GlidArc’ within Horizon2020 (Grant No.657304) and the FWO project (grant G.0383.16N). The computational work was carried out using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UA), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UA. | Approved | Most recent IF: 3.302 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:135515 | Serial | 4281 | ||
| Permanent link to this record | |||||
| Author | Wang, W.; Berthelot, A.; Kolev, S.; Tu, X.; Bogaerts, A. | ||||
| Title | CO2 conversion in a gliding arc plasma: 1D cylindrical discharge model | Type | A1 Journal article | ||
| Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 065012 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | CO 2 conversion by a gliding arc plasma is gaining increasing interest, but the underlying mechanisms for an energy-efficient process are still far from understood. Indeed, the chemical complexity of the non-equilibrium plasma poses a challenge for plasma modeling due to the huge computational load. In this paper, a one-dimensional (1D) gliding arc model is developed in a cylindrical frame, with a detailed non-equilibrium CO 2 plasma chemistry set, including the CO 2 vibrational kinetics up to the dissociation limit. The model solves a set of time- dependent continuity equations based on the chemical reactions, as well as the electron energy balance equation, and it assumes quasi-neutrality in the plasma. The loss of plasma species and heat due to convection by the transverse gas flow is accounted for by using a characteristic frequency of convective cooling, which depends on the gliding arc radius, the relative velocity of the gas flow with respect to the arc and on the arc elongation rate. The calculated values for plasma density and plasma temperature within this work are comparable with experimental data on gliding arc plasma reactors in the literature. Our calculation results indicate that excitation to the vibrational levels promotes efficient dissociation in the gliding arc, and this is consistent with experimental investigations of the gliding arc based CO 2 conversion in the literature. Additionally, the dissociation of CO 2 through collisions with O atoms has the largest contribution to CO 2 splitting under the conditions studied. In addition to the above results, we also demonstrate that lumping the CO 2 vibrational states can bring a significant reduction of the computational load. The latter opens up the way for 2D or 3D models with an accurate description of the CO 2 vibrational kinetics. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000386605100002 | Publication Date | 2016-10-18 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 3 | Open Access | |
| Notes | This research was supported by the European Marie Skłodowska-Curie Individual Fellowship ‘GlidArc’ within Horizon2020 (Grant No. 657304) and by the FWO project (grant G.0383.16N). The calculations were performed using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UAntwerpen), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UAntwerpen. | Approved | Most recent IF: 3.302 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:135990 | Serial | 4286 | ||
| Permanent link to this record | |||||
| Author | Meledin, A.; Turner, S.; Cayado, P.; Mundet, B.; Solano, E.; Ricart, S.; Ros, J.; Puig, T.; Obradors, X.; Van Tendeloo, G. | ||||
| Title | Unique nanostructural features in Fe, Mn-doped YBCO thin films | Type | A1 Journal article | ||
| Year | 2016 | Publication | Superconductor science and technology | Abbreviated Journal | Supercond Sci Tech |
| Volume | 29 | Issue | 29 | Pages | 125009 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | An attempt to grow a thin epitaxial composite film of YBa2Cu3O7−δ (YBCO) with spinel MnFe2O4 (MFO) nanoparticles on a LAO substrate using the CSD approach resulted in a decomposition of the spinel and various doping modes of YBCO with the Fe and Mn cations. These nanostructural effects lead to a lowering of T c and a slight J c increase in field. Using a combination of advanced transmission electron microscopy (TEM) techniques such as atomic resolution high-angle annular dark field scanning TEM, energy dispersive x-ray spectroscopy and electron energy-loss spectroscopy we have been able to decipher and characterize the effects of the Fe and Mn doping on the film architecture. The YBaCuFeO5 anion-deficient double perovskite phase was detected in the form of 3D inclusions as well as epitaxially grown lamellas within the YBCO matrix. These nano-inclusions play a positive role as pinning centers responsible for the J c/J sf (H) dependency smoothening at high magnetic fields in the YBCO-MFO films with respect to the pristine YBCO films. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000387680100001 | Publication Date | 2016-10-31 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0953-2048 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 2.878 | Times cited | 6 | Open Access | |
| Notes | The authors gratefully acknowledge Prof. Dr. A. Abakumov and Dr. J. Gazquez for discussions and corrections. Part of this work was performed within the framework of the EUROTAPES project (FP7-NMP.2011.2.2-1 Grant no. 280432), funded by the European Union. ICMAB research was financed by the Ministry of Economy and Competitiveness, and FEDER funds under the projects MAT2011-28874-C02-01, MAT2014-51778-C2-1-R, ENE2014-56109-C3-3-R and Consolider Nanoselect CSD2007-00041, and by Generalitat de Catalunya (2009 SGR 770, 2015 SGR 753 and Xarmae). ICMAB acknowledges support from Severo Ochoa Program (MINECO, Grant SEV-2015-0496). | Approved | Most recent IF: 2.878 | ||
| Call Number | EMAT @ emat @ c:irua:136444 | Serial | 4295 | ||
| Permanent link to this record | |||||
| Author | Chizhov, A.S.; Rumyantseva, M.N.; Vasiliev, R.B.; Filatova, D.G.; Drozdov, K.A.; Krylov, I.V.; Marchevsky, A.V.; Karakulina, O.M.; Abakumov, A.M.; Gaskov, A.M. | ||||
| Title | Visible light activation of room temperature NO2 gas sensors based on ZnO, SnO2 and In2O3 sensitized with CdSe quantum dots | Type | A1 Journal article | ||
| Year | 2016 | Publication | Thin solid films : an international journal on the science and technology of thin and thick films | Abbreviated Journal | Thin Solid Films |
| Volume | 618 | Issue | 618 | Pages | 253-262 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | This work reports the analysis of visible light activation of room temperature NO2 gas sensitivity of metal oxide semiconductors (MOS): blank and CdSe quantum dots (QDs) sensitized nanocrystallinematrixes ZnO, SnO2 and In2O3. Nanocrystalline metal oxides (MOx) ZnO, SnO2, In2O3 were synthesized by the precipitation method. Colloidal CdSe QDs were obtained by high temperature colloidal synthesis. Sensitization was effectuated by direct adsorption of CdSe QDs stabilized with oleic acid on MOx surface. The role of illumination consists in generation of electrons, which can be transferred into MOx conduction band, and holes that can recombine with the electrons previously trapped by the chemisorbed acceptor species and thus activate desorption of analyte molecules. Under green light illumination for blank SnO2 and In2O3 matrixes the indirect consequential mechanism for the generation of holes is proposed. Anothermechanismis realized in the presence of CdSe QDs. In this case the electron-hole pair is generated in the CdSe quantum dot. Sensor measurements demonstrated that synthesizedmaterials can be used for NO2 detection under visible (green) light illumination at room temperature without any thermal heating. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000389164400005 | Publication Date | 2016-09-18 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0040-6090 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 1.879 | Times cited | 19 | Open Access | |
| Notes | The work was financially supported by Russian Foundation for Basic Research grant no. 15-03-03026. | Approved | Most recent IF: 1.879 | ||
| Call Number | EMAT @ emat @ c:irua:138598 | Serial | 4321 | ||
| Permanent link to this record | |||||
| Author | Jacobs, W.; Reynaerts, C.; Andries, S.; van den Akker, S.; Moonen, N.; Lamoen, D. | ||||
| Title | Analyzing the dispersion of cargo vapors around a ship’s superstructure by means of wind tunnel experiments | Type | A1 Journal article | ||
| Year | 2016 | Publication | Journal of marine science and technology | Abbreviated Journal | J Mar Sci Tech-Japan |
| Volume | 21 | Issue | 21 | Pages | 758-766 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | In a previous study, it was found that cargo tank operations like cleaning and venting, lead to higher cargo vapor concentrations around the ship’s superstructure. Can wind tunnel experiments confirm these findings? Is there an improvement when using higher outlets at high velocities compared to lower outlets with a low outlet velocity? Is there a relation between relative wind speed and measured concentration? These questions were investigated in the Peutz wind tunnel. By using a tracer gas for the wind tunnel experiments, concentration coefficients have been calculated for various settings. The study shows that using high-velocity outlets is an efficient way to keep concentrations as low as possible. The only exception is for relative wind directions from the bow. In this last case using a manhole as ventilation outlet leads to lower concentrations. With increasing wind speeds the building downwash effect resulted in higher concentration coefficients near the main deck. This study confirms our on-board measurements and suggests the lowering of the ventilation inlet of the accommodation, so that the high-velocity outlet can be used safely at all times. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000388260200015 | Publication Date | 2016-05-21 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0948-4280 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 0.838 | Times cited | 2 | Open Access | |
| Notes | The authors would like to thank Peutz bv. at Molenhoek, the Netherlands, for providing the wind tunnel facilities and their assistance during the various stages of this research. | Approved | Most recent IF: 0.838 | ||
| Call Number | EMAT @ emat @ c:irua:138728 | Serial | 4326 | ||
| Permanent link to this record | |||||
| Author | Van Aelst, J.; Philippaerts, A.; Bartholomeeusen, E.; Fayad, E.; Thibault-Starzyk, F.; Lu, J.; Schryvers, D.; Ooms, R.; Verboekend, D.; Jacobs, P.; Sels, B. | ||||
| Title | Towards biolubricant compatible vegetable oils by pore mouth hydrogenation with shape-selective Pt/ZSM-5 catalysts | Type | A1 Journal article | ||
| Year | 2016 | Publication | Catalysis science & technology | Abbreviated Journal | Catal Sci Technol |
| Volume | 6 | Issue | 6 | Pages | 2820-2828 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Pt/ZSM-5 catalysts with various crystal sizes were prepared via competitive ion-exchange, followed by a slow activation procedure. Even when using very large ZSM-5 crystals, highly dispersed Pt nano-clusters were contained within the zeolite crystal's voids, as ascertained by 2D pressure-jump IR spectroscopy of adsorbed CO and focussed ion-beam transmission electron microscopy. The shape-selective properties of the Pt/ZSM-5 catalysts were evaluated in the partial hydrogenation of soybean oil. Unique hydrogenation selectivities were observed, as the fatty acids located at the central position of the triacylglycerol (TAG) molecules were preferentially hydrogenated. The resulting oil has therefore high levels of intermediately melting TAGs, which are compatible with biolubricants due to their improved oxidative stability and still appropriate low-temperature fluidity. The TAG distribution in the partially hydrogenated soybean oil samples was independent from the zeolite crystal size, while the hydrogenation activity linearly increases with the crystal's external surface area. This trend was confirmed with a Pt loaded mesoporous ZSM-5 zeolite, obtained via a mild alkaline treatment. These observations imply and confirm a genuine pore mouth catalysis mechanism, in which only one fatty acid chain of the TAG is able to enter the micropores of ZSM-5, where the double bonds are hydrogenated by the crystal encapsulated Pt-clusters. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000374790200031 | Publication Date | 2016-03-31 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2044-4753 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 5.773 | Times cited | 5 | Open Access | |
| Notes | The research was funded through a PhD grant to J. V. A. of the Agency for Innovation by Science and Technology in Flanders (IWT). A. P. and D. V. acknowledge the F. W. O.-Vlaanderen (Research Foundation Flanders) for a post-doctoral fellowship. E. B. was kindly funded by an F. W. O.-Vlaanderen project. This work was performed in the framework of an Associated International Laboratory between FWO and CNRS. | Approved | Most recent IF: 5.773 | ||
| Call Number | EMAT @ emat @ c:irua:138981 | Serial | 4335 | ||
| Permanent link to this record | |||||
| Author | Sun, S.R.; Kolev, S.; Wang, H.X.; Bogaerts, A. | ||||
| Title | Coupled gas flow-plasma model for a gliding arc: investigations of the back-breakdown phenomenon and its effect on the gliding arc characteristics | Type | A1 Journal article | ||
| Year | 2017 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 26 | Issue | 26 | Pages | 015003 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | We present a 3D and 2D Cartesian quasi-neutral plasma model for a low current argon gliding arc discharge, including strong interactions between the gas flow and arc plasma column. The 3D model is applied only for a short time of 0.2 ms due to its huge computational cost. It mainly serves to verify the reliability of the 2D model. As the results in 2D compare well with those in 3D, they can be used for a better understanding of the gliding arc basic characteristics. More specifically, we investigate the back-breakdown phenomenon induced by an artificially controlled plasma channel, and we discuss its effect on the gliding arc characteristics. The back-breakdown phenomenon, or backward-jump motion of the arc, as observed in the experiments, results in a drop of the gas temperature, as well as in a delay of the arc velocity with respect to the gas flow velocity, allowing more gas to pass through the arc, and thus increasing the efficiency of the gliding arc for gas treatment applications. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000419253000001 | Publication Date | 2016-11-22 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 9 | Open Access | OpenAccess |
| Notes | This work is financially supported by the Methusalem financing, by the Fund for Scientific Research Flanders (FWO) and by the IAP/7 (Inter-university Attraction Pole) program ‘Physical Chemistry of Plasma-Surface Interactions’ from the Belgian Federal Office for Science Policy (BELSPO). The work was carried out in part using the Turing HPC infrastructure of the CalcUA core facility of the Universiteit Antwerpen, a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the Universiteit Antwerpen. This work was also supported by the National Natural Science Foundation of China (Grant Nos. 11275021, 11575019). S R Sun thanks the financial support from the China Scholarship Council. | Approved | Most recent IF: 3.302 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:138993 | Serial | 4337 | ||
| Permanent link to this record | |||||
| Author | Trenchev, G.; Kolev, S.; Kiss’ovski, Z. | ||||
| Title | Modeling a Langmuir probe in atmospheric pressure plasma at different EEDFs | Type | A1 Journal article | ||
| Year | 2017 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 26 | Issue | 26 | Pages | 055013 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | In this study, we present a computational model of a cylindrical electric probe in atmospheric pressure argon plasma. The plasma properties are varied in terms of density and electron temperature. Furthermore, results for plasmas with Maxwellian and non-Maxwellian electron energy distribution functions are also obtained and compared. The model is based on the fluid description of plasma within the COMSOL software package. The results for the ion saturation current are compared and show good agreement with existing analytical Langmuir probe theories. A strong dependence between the ion saturation current and electron transport properties was observed, and attributed to the effects of ambipolar diffusion. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000398327900002 | Publication Date | 2017-04-03 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 4 | Open Access | OpenAccess |
| Notes | Approved | Most recent IF: 3.302 | |||
| Call Number | PLASMANT @ plasmant @ c:irua:141914 | Serial | 4535 | ||
| Permanent link to this record | |||||
| Author | Tennyson, J.; Rahimi, S.; Hill, C.; Tse, L.; Vibhakar, A.; Akello-Egwel, D.; Brown, D.B.; Dzarasova, A.; Hamilton, J.R.; Jaksch, D.; Mohr, S.; Wren-Little, K.; Bruckmeier, J.; Agarwal, A.; Bartschat, K.; Bogaerts, A.; Booth, J.-P.; Goeckner, M.J.; Hassouni, K.; Itikawa, Y.; Braams, B.J.; Krishnakumar, E.; Laricchiuta, A.; Mason, N.J.; Pandey, S.; Petrovic, Z.L.; Pu, Y.-K.; Ranjan, A.; Rauf, S.; Schulze, J.; Turner, M.M.; Ventzek, P.; Whitehead, J.C.; Yoon, J.-S. | ||||
| Title | QDB: a new database of plasma chemistries and reactions | Type | A1 Journal article | ||
| Year | 2017 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 26 | Issue | 26 | Pages | 055014 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | One of the most challenging and recurring problems when modeling plasmas is the lack of data on the key atomic and molecular reactions that drive plasma processes. Even when there are data for some reactions, complete and validated datasets of chemistries are rarely available. This hinders research on plasma processes and curbs development of industrial applications. The QDB project aims to address this problem by providing a platform for provision, exchange, and validation of chemistry datasets. A new data model developed for QDB is presented. QDB collates published data on both electron scattering and heavy-particle reactions. These data are formed into reaction sets, which are then validated against experimental data where possible. This process produces both complete chemistry sets and identifies key reactions that are currently unreported in the literature. Gaps in the datasets can be filled using established theoretical methods. Initial validated chemistry sets for SF6/CF4/O2 and SF6/CF4/N2/H2 are presented as examples. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000398394500001 | Publication Date | 2017-04-04 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 18 | Open Access | OpenAccess |
| Notes | Approved | Most recent IF: 3.302 | |||
| Call Number | PLASMANT @ plasmant @ c:irua:142206 | Serial | 4549 | ||
| Permanent link to this record | |||||
| Author | Sun, S.R.; Kolev, S.; Wang, H.X.; Bogaerts, A. | ||||
| Title | Investigations of discharge and post-discharge in a gliding arc: a 3D computational study | Type | A1 Journal article | ||
| Year | 2017 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 26 | Issue | 26 | Pages | 055017 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | In this study we quantitatively investigate for the first time the plasma characteristics of an argon gliding arc with a 3D model. The model is validated by comparison with available experimental data from literature and a reasonable agreement is obtained for the calculated gas temperature and electron density. A complete arc cycle is modeled from initial ignition to arc decay. We investigate how the plasma characteristics, i.e., the electron temperature, gas temperature, reduced electric field, and the densities of electrons, Ar+ and Ar2+ ions and Ar(4s) excited states, vary over one complete arc cycle, including their behavior in the discharge and post-discharge. These plasma characteristics exhibit a different evolution over one arc cycle, indicating that either the active discharge stage or the post-discharge stage can be beneficial for certain applications. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000399278100002 | Publication Date | 2017-04-05 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 11 | Open Access | OpenAccess |
| Notes | This work is financially supported by the Methusalem financing, by the Fund for Scientific Research Flanders (FWO) and by the IAP/7 (Inter-university Attraction Pole) program ‘Physical Chemistry of Plasma-Surface Interactions’ from the Belgian Federal Office for Science Policy (BELSPO). The work was carried out in part using the Turing HPC infrastructure of the CalcUA core facility of the Universiteit Antwerpen, a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the Universiteit Antwerpen. This work was also supported by the National Natural Science Foundation of China (Grant Nos. 11275021, 11575019). SR Sun thanks the financial support from the China Scholarship Council (CSC). | Approved | Most recent IF: 3.302 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:142204 | Serial | 4550 | ||
| Permanent link to this record | |||||
| Author | Zhang, Y.; Wang, H.-yu; Zhang, Y.-ru; Bogaerts, A. | ||||
| Title | Formation of microdischarges inside a mesoporous catalyst in dielectric barrier discharge plasmas | Type | A1 Journal article | ||
| Year | 2017 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 26 | Issue | 26 | Pages | 054002 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | The formation process of a microdischarge (MD) in both μm- and nm-sized catalyst pores is simulated by a two-dimensional particle-in-cell/Monte Carlo collision model. A parallel-plate dielectric barrier discharge configuration in filamentary mode is considered in ambient air. The discharge is powered by a high voltage pulse. Our calculations reveal that a streamer can penetrate into the surface features of a porous catalyst and MDs can be formed inside both μm- and nm-sized pores, yielding ionization inside the pore. For the μm-sized pores, the ionization mainly occurs inside the pore, while for the nm-sized pores the ionization is strongest near and inside the pore. Thus, enhanced discharges near and inside the mesoporous catalyst are observed. Indeed, the maximum values of the electric field, ionization rate and electron density occur near and inside the pore. The maximum electric field and electron density inside the pore first increase when the pore size rises from 4 nm to 10 nm, and then they decrease for the 100 nm pore, due to a more pronounced surface discharge for the smaller pores. However, the ionization rate is highest for the 100 nm pore due to the largest effective ionization region. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000399277700001 | Publication Date | 2017-04-05 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 15 | Open Access | OpenAccess |
| Notes | This work was supported by the NSFC (11405067, 11275007, 11375163). Y Zhang gratefully acknowledges the Belgian Federal Science Policy Office for financial support. The authors are very grateful to Wei Jiang for the useful discussions on the photo-ionization model and the particle-incell/ Monte-Carlo model. | Approved | Most recent IF: 3.302 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:142806 | Serial | 4566 | ||
| Permanent link to this record | |||||
| Author | Bogaerts, A.; Berthelot, A.; Heijkers, S.; Kolev, S.; Snoeckx, R.; Sun, S.; Trenchev, G.; Van Laer, K.; Wang, W. | ||||
| Title | CO2conversion by plasma technology: insights from modeling the plasma chemistry and plasma reactor design | Type | A1 Journal article | ||
| Year | 2017 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 26 | Issue | 26 | Pages | 063001 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | In recent years there has been growing interest in the use of plasma technology for CO2 conversion. To improve this application, a good insight into the underlying mechanisms is of great importance. This can be obtained from modeling the detailed plasma chemistry in order to understand the chemical reaction pathways leading to CO2 conversion (either in pure form or mixed with another gas). Moreover, in practice, several plasma reactor types are being investigated for CO2 conversion, so in addition it is essential to be able to model these reactor geometries so that their design can be improved, and the most energy efficient CO2 conversion can be achieved. Modeling the detailed plasma chemistry of CO2 conversion in complex reactors is, however, very time-consuming. This problem can be overcome by using a combination of two different types of model: 0D chemical reaction kinetics models are very suitable for describing the detailed plasma chemistry, while the characteristic features of different reactor geometries can be studied by 2D or 3D fluid models. In the first instance the latter can be developed in argon or helium with a simple chemistry to limit the calculation time; however, the ultimate aim is to implement the more complex CO2 chemistry in these models. In the present paper, examples will be given of both the 0D plasma chemistry models and the 2D and 3D fluid models for the most common plasma reactors used for CO2 conversion in order to emphasize the complementarity of both approaches. Furthermore, based on the modeling insights, the paper discusses the possibilities and limitations of plasma-based CO2 conversion in different types of plasma reactors, as well as what is needed to make further progress in this field. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000412173700001 | Publication Date | 2017-05-15 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 26 | Open Access | OpenAccess |
| Notes | We would like to thank T Silva, N Britoun, Th Godfroid and R Snyders (Université de Mons and Materia Nova Research Center), A Ozkan, Th Dufour and F Reniers (Université Libre de Bruxelles) andK Van Wesenbeeck and S Lenaerts (University of Antwerp) for providingexperimental data to validate our models. Furthermore, we acknowledge the financial support from the IAP/7 (Inter-university Attraction Pole) program ‘PSI-Physical Chemistry of Plasma-Surface Interactions’ by the Belgian Federal Office for Science Policy (BELSPO), the Francqui Research Foundation, the European Union’s Seventh Framework Programme for research, technological development and demonstration under grant agreement no. 606889, the European Marie Skłodowska- Curie Individual Fellowship project ‘GlidArc’ within Horizon2020, the Methusalem financing of the University of Antwerp, the Fund for Scientific Research, Flanders (FWO; grant nos. G.0383.16N and 11U5316N) and the Institute for the Promotion of Innovation by Science and Technology in Flanders (IWT Flanders). The calculations were carried out using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UAntwerpen), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UAntwerpen. | Approved | Most recent IF: 3.302 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:144429 | Serial | 4614 | ||
| Permanent link to this record | |||||
| Author | Navarrete, A.; Centi, G.; Bogaerts, A.; Mart?n,?ngel; York, A.; Stefanidis, G.D. | ||||
| Title | Harvesting Renewable Energy for Carbon Dioxide Catalysis | Type | A1 Journal article | ||
| Year | 2017 | Publication | Energy technology | Abbreviated Journal | Energy Technol-Ger |
| Volume | 5 | Issue | 5 | Pages | 796-811 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | The use of renewable energy (RE) to transform carbon dioxide into commodities (i.e., CO2 valorization) will pave the way towards a more sustainable economy in the coming years. But how can we efficiently use this energy (mostly available as electricity or solar light) to drive the necessary (catalytic) transformations? This paper presents a review of the technological advances in the transformation of carbon dioxide by means of RE. The socioeconomic implications and chemical basis of the transformation of carbon dioxide with RE are discussed. Then a general view of the use of RE to activate the (catalytic) transformations of carbon dioxide with microwaves, plasmas, and light is presented. The fundamental phenomena involved are introduced from a catalytic and reaction device perspective to present the advantages of this energy form as well as the inherent limitations of the present state-of-the-art. It is shown that efficient use of RE requires the redesign of current catalytic concepts. In this context, a new kind of reaction system, an energy-harvesting device, is proposed as a new conceptual approach for this endeavor. Finally, the challenges that lie ahead for the efficient and economical use of RE for carbon dioxide conversion are exposed. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000451619500001 | Publication Date | 2017-02-08 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2194-4288 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 2.789 | Times cited | 15 | Open Access | Not_Open_Access |
| Notes | Fund for Scientific Research Flanders, G.0254.14 N, G.0217.14 N and G.0383.16 N ; Spanish Ministry of Economy and Competitiveness, ENE2014-53459-R ; | Approved | Most recent IF: 2.789 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:144217 | Serial | 4615 | ||
| Permanent link to this record | |||||
| Author | Bruggeman, P.J.; Kushner, M.J.; Locke, B.R.; Gardeniers, J.G.E.; Graham, W.G.; Graves, D.B.; Hofman-Caris, R.C.H.M.; Maric, D.; Reid, J.P.; Ceriani, E.; Fernandez Rivas, D.; Foster, J.E.; Garrick, S.C.; Gorbanev, Y.; Hamaguchi, S.; Iza, F.; Jablonowski, H.; Klimova, E.; Kolb, J.; Krcma, F.; Lukes, P.; Machala, Z.; Marinov, I.; Mariotti, D.; Mededovic Thagard, S.; Minakata, D.; Neyts, E.C.; Pawlat, J.; Petrovic, Z.L.; Pflieger, R.; Reuter, S.; Schram, D.C.; Schröter, S.; Shiraiwa, M.; Tarabová, B.; Tsai, P.A.; Verlet, J.R.R.; von Woedtke, T.; Wilson, K.R.; Yasui, K.; Zvereva, G. | ||||
| Title | Plasma–liquid interactions: a review and roadmap | Type | A1 Journal article | ||
| Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 5 | Pages | 053002 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Plasma–liquid interactions represent a growing interdisciplinary area of research involving plasma science, fluid dynamics, heat and mass transfer, photolysis, multiphase chemistry and aerosol science. This review provides an assessment of the state-of-the-art of this multidisciplinary area and identifies the key research challenges. The developments in diagnostics, modeling and further extensions of cross section and reaction rate databases that are necessary to address these challenges are discussed. The review focusses on nonequilibrium plasmas. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000384715400001 | Publication Date | 2016-09-30 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 460 | Open Access | |
| Notes | This manuscript originated from discussions at the Lorentz Center Workshop ‘Gas/Plasma–Liquid Interface: Transport, Chemistry and Fundamental Data’ that took place at the Lorentz Center, Leiden University in the Netherlands from August 4, through August 8, 2014, and follow-up discussions since the workshop. All authors acknowledge the support of the Lorentz Center, the COST action TD1208 (Electrical Discharges with Liquids for Future Applications) and the Royal Dutch Academy of Sciences for their financial support. PJB, MJK, DBG and JEF acknowledge the support of the ‘Center on Control of Plasma Kinetics’ of the United States Department of Energy Office of Fusion Energy Science (DE-SC0001319). In addition, PJB and BRL acknowledge the support of the National Science Foundation (PHY 1500135 and CBET 1236225, respectively). In addition the enormous help of Mrs. Victoria Piorek (University of Minnesota) in the formatting of the final document including the references is gratefully acknowledged. | Approved | Most recent IF: 3.302 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:144654 | Serial | 4628 | ||
| Permanent link to this record | |||||
| Author | Van Laer, K.; Bogaerts, A. | ||||
| Title | How bead size and dielectric constant affect the plasma behaviour in a packed bed plasma reactor: a modelling study | Type | A1 Journal article | ||
| Year | 2017 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 26 | Issue | 26 | Pages | 085007 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Packed bed plasma reactors (PBPRs) are gaining increasing interest for use in environmental applications, such as greenhouse gas conversion into value-added chemicals or renewable fuels and volatile pollutant removal (e.g. NOx, VOC, K), as they enhance the conversion and energy efficiency of the process compared to a non-packed reactor. However, the plasma behaviour in a PBPR is not well understood. In this paper we demonstrate, by means of a fluid model, that the discharge behaviour changes considerably when changing the size of the packing beads and their dielectric constant, while keeping the interelectrode spacing constant. At low dielectric constant, the plasma is spread out over the full discharge gap, showing significant density in the voids as well as in the connecting void channels. The electric current profile shows a strong peak during each half cycle. When the dielectric constant increases, the plasma becomes localised in the voids, with a current profile consisting of many smaller peaks during each half cycle. For large bead sizes, the shift from full gap discharge to localised discharges takes place at a higher dielectric constant than for smaller beads. Furthermore, smaller beads or beads with a lower dielectric constant require a higher breakdown voltage to cause plasma formation. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000406503600003 | Publication Date | 2017-07-27 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 22 | Open Access | OpenAccess |
| Notes | K Van Laer is indebted to the Institute for the Promotion of Innovation by Science and Technology in Flanders (IWT Flanders) for financial support. This research was carried out in the framework of the network on Physical Chemistry of Plasma-Surface Interactions – Interuniversity Attraction Poles, phase VII (http://psi-iap7.ulb.ac.be/), and supported by the Belgian Science Policy Office (BELSPO). The calculations were carried out using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UAntwerpen), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UAntwerpen. | Approved | Most recent IF: 3.302 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:144796 | Serial | 4635 | ||
| Permanent link to this record | |||||
| Author | Singh, V.; Mehta, B.R.; Sengar, S.K.; Karakulina, O.M.; Hadermann, J.; Kaushal, A. | ||||
| Title | Achieving independent control of core diameter and carbon shell thickness in Pd-C core–shell nanoparticles by gas phase synthesis | Type | A1 Journal article | ||
| Year | 2017 | Publication | Nanotechnology | Abbreviated Journal | Nanotechnology |
| Volume | 28 | Issue | 29 | Pages | 295603 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Pd-C core–shell nanoparticles with independently controllable core size and shell thickness are grown by gas phase synthesis. First, the core size is selected by electrical mobility values of charged particles, and second, the shell thickness is controlled by the concentration of carbon precursor gas. The carbon shell grows by adsorption of carbon precursor gas molecules on the surface of nanoparticles, followed by sintering. The presence of a carbon shell on Pd nanoparticles is potentially important in hydrogen-related applications operating at high temperatures or in catalytic reactions in acidic/aqueous environments. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000404633200002 | Publication Date | 2017-06-28 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0957-4484 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.44 | Times cited | 1 | Open Access | Not_Open_Access |
| Notes | VS is thankful to the All India Council for Technical Education, India, for providing assistantship under its Quality Improvement Programme. BRM gratefully acknowledges the support of the Nanomission Programme of the Department of Science and Technology (DST), India and Schlumberger Chair Professorship. BRM would also like to acknowledge the support from the project funded by BRNS, DAE, India. | Approved | Most recent IF: 3.44 | ||
| Call Number | EMAT @ emat @c:irua:144831 | Serial | 4712 | ||
| Permanent link to this record | |||||
| Author | Ramakers, M.; Medrano, J.A.; Trenchev, G.; Gallucci, F.; Bogaerts, A. | ||||
| Title | Revealing the arc dynamics in a gliding arc plasmatron: a better insight to improve CO2conversion | Type | A1 Journal article | ||
| Year | 2017 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 26 | Issue | 12 | Pages | 125002 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | A gliding arc plasmatron (GAP) is very promising for CO2 conversion into value-added chemicals, but to further improve this important application, a better understanding of the arc behavior is indispensable. Therefore, we study here for the first time the dynamic arc behavior of the GAP by means of a high-speed camera, for different reactor configurations and in a wide range of operating conditions. This allows us to provide a complete image of the behavior of the gliding arc. More specifically, the arc body shape, diameter, movement and rotation speed are analyzed and discussed. Clearly, the arc movement and shape relies on a number of factors, such as gas turbulence, outlet diameter, electrode surface, gas contraction and buoyance force. Furthermore, we also compare the experimentally measured arc movement to a state-of-the-art 3D-plasma model, which predicts the plasma movement and rotation speed with very good accuracy, to gain further insight in the underlying mechanisms. Finally, we correlate the arc dynamics with the CO2 conversion and energy efficiency, at exactly the same conditions, to explain the effect of these parameters on the CO2 conversion process. This work is important for understanding and optimizing the GAP for CO2 conversion. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000414675000001 | Publication Date | 2017-11-07 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 7 | Open Access | OpenAccess |
| Notes | This work was supported by the Belgian Federal Office for Science Policy (BELSPO) and the Fund for Scientific Research Flanders (FWO; grant numbers G.0383.16N and 11U5316N). | Approved | Most recent IF: 3.302 | ||
| Call Number | PLASMANT @ plasmant @c:irua:147023 | Serial | 4761 | ||
| Permanent link to this record | |||||
| Author | Berthelot, A.; Bogaerts, A. | ||||
| Title | Modeling of CO2plasma: effect of uncertainties in the plasma chemistry | Type | A1 Journal article | ||
| Year | 2017 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 26 | Issue | 11 | Pages | 115002 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Low-temperature plasma chemical kinetic models are particularly important to the plasma community. These models typically require dozens of inputs, especially rate coefficients. The latter are not always precisely known and it is not surprising that the error on the rate coefficient data can propagate to the model output. In this paper, we present a model that uses N = 400 different combinations of rate coefficients based on the uncertainty attributed to each rate coefficient, giving a good estimation of the uncertainty on the model output due to the rate coefficients. We demonstrate that the uncertainty varies a lot with the conditions and the type of output. Relatively low uncertainties (about 15%) are found for electron density and temperature, while the uncertainty can reach more than an order of magnitude for the population of the vibrational levels in some cases and it can rise up to 100% for the CO2 conversion. The reactions that are mostly responsible for the largest uncertainties are identified. We show that the conditions of pressure, gas temperature and power density have a great effect on the uncertainty and on which reactions lead to this uncertainty. In all the cases tested here, while the absolute values may suffer from large uncertainties, the trends observed in previous modeling work are still valid. Finally, in accordance with the work of Turner, a number of ‘good practices’ is recommended. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000413216500002 | Publication Date | 2017-10-18 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 16 | Open Access | OpenAccess |
| Notes | We acknowledge financial support from the European Unions Seventh Framework Program for research, technological development and demonstration under grant agreement n◦ 606889. The calculations were carried out using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UA), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UA. | Approved | Most recent IF: 3.302 | ||
| Call Number | PLASMANT @ plasmant @c:irua:146879c:irua:146642 | Serial | 4758 | ||
| Permanent link to this record | |||||
| Author | Vishwakarma, M.; Karakulina, O.M.; Abakumov, A.M.; Hadermann, J.; Mehta, B.R. | ||||
| Title | Nanoscale Characterization of Growth of Secondary Phases in Off-Stoichiometric CZTS Thin Films | Type | A1 Journal article | ||
| Year | 2018 | Publication | Journal of nanoscience and nanotechnology | Abbreviated Journal | J Nanosci Nanotechno |
| Volume | 18 | Issue | 3 | Pages | 1688-1695 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
| Abstract | The presence of secondary phases is one of the main issues that hinder the growth of pure kesterite Cu2ZnSnS4 (CZTS) based thin films with suitable electronic and junction properties for efficient solar cell devices. In this work, CZTS thin films with varied Zn and Sn content have been prepared by RF-power controlled co-sputtering deposition using Cu, ZnS and SnS targets and a subsequent sulphurization step. Detailed TEM investigations show that the film shows a layered structure with the majority of the top layer being the kesterite phase. Depending on the initial thin film composition, either about ~1 μm Cu-rich and Zn-poor kesterite or stoichiometric CZTS is formed as top layer. X-ray diffraction, Raman spectroscopy and transmission electron microscopy reveal the presence of Cu2−x S, ZnS and SnO2 minor secondary phases in the form of nanoinclusions or nanoparticles or intermediate layers. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000426033400022 | Publication Date | 2018-03-01 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1533-4880 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 1.483 | Times cited | Open Access | Not_Open_Access | |
| Notes | Manoj Vishwakarma acknowl- edges IIT Delhi for MHRD fellowship. Professor B. R. Mehta acknowledges the support of the Schlumberger chair professorship. Manoj Vishwakarma, Joke Hadermann and Olesia M. karakulina acknowledge support provided by InsoL-DST. Manoj Vishwakarma acknowledges sup- port provided by CSIR funded projects and the support of DST-FIST Raman facility. References | Approved | Most recent IF: 1.483 | ||
| Call Number | EMAT @ emat @c:irua:147505 | Serial | 4775 | ||
| Permanent link to this record | |||||
| Author | Alves, L.L.; Bogaerts, A.; Guerra, V.; Turner, M.M. | ||||
| Title | Foundations of modelling of nonequilibrium low-temperature plasmas | Type | A1 Journal article | ||
| Year | 2018 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 27 | Issue | 2 | Pages | 023002 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | This work explains the need for plasma models, introduces arguments for choosing the type of model that better fits the purpose of each study, and presents the basics of the most common nonequilibrium low-temperature plasma models and the information available from each one, along with an extensive list of references for complementary in-depth reading. The paper presents the following models, organised according to the level of multi-dimensional description of the plasma: kinetic models, based on either a statistical particle-in-cell/Monte-Carlo approach or the solution to the Boltzmann equation (in the latter case, special focus is given to the description of the electron kinetics); multi-fluid models, based on the solution to the hydrodynamic equations; global (spatially-average) models, based on the solution to the particle and energy rate-balance equations for the main plasma species, usually including a very complete reaction chemistry; mesoscopic models for plasma–surface interaction, adopting either a deterministic approach or a stochastic dynamical Monte-Carlo approach. For each plasma model, the paper puts forward the physics context, introduces the fundamental equations, presents advantages and limitations, also from a numerical perspective, and illustrates its application with some examples. Whenever pertinent, the interconnection between models is also discussed, in view of multi-scale hybrid approaches. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Wos | 000425688600001 | Publication Date | 2018-02-20 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 17 | Open Access | OpenAccess |
| Notes | The authors would like to thank A Tejero-Del-Caz and A Berthelot for their technical contributions in writing the manuscript. This work was partially funded by Portuguese FCT —Fundação para a Ciência e a Tecnologia, under projects UID/ FIS/50010/2013, PTDC/FISPLA/1243/2014 (KIT-PLAS- MEBA) and PTDC/FIS-PLA/1420/2014 (PREMiERE). | Approved | Most recent IF: 3.302 | ||
| Call Number | PLASMANT @ plasmant @c:irua:149391 | Serial | 4810 | ||
| Permanent link to this record | |||||