Home | << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 >> |
![]() |
Records | |||||
---|---|---|---|---|---|
Author | Van Turnhout, J.; Aceto, D.; Travert, A.; Bazin, P.; Thibault-Starzyk, F.; Bogaerts, A.; Azzolina-Jury, F. | ||||
Title | Observation of surface species in plasma-catalytic dry reforming of methane in a novel atmospheric pressure dielectric barrier discharge in situ IR cell | Type | A1 Journal article | ||
Year | 2022 | Publication | Catalysis Science & Technology | Abbreviated Journal | Catal Sci Technol |
Volume | 12 | Issue ![]() |
22 | Pages | 6676-6686 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | We developed a novel in situ (i.e. inside plasma and during operation) IR dielectric barrier discharge cell allowing investigation of plasma catalysis in transmission mode, atmospheric pressure, flow conditions (WHSV similar to 0-50 000 mL g(-1) h(-1)), at relevant discharge voltages (similar to 0-50 kV) and frequencies (similar to 0-5 kHz). We applied it to study the IR-active surface species formed on a SiO2 support and on a 3 wt% Ru/SiO2 catalyst, which can help to reveal the important surface reaction mechanisms during the plasma-catalytic dry reforming of methane (DRM). Moreover, we present a technique for the challenging task of estimating the temperature of a catalyst sample in a plasma-catalytic system in situ and during plasma operation. We found that during the reaction, water is immediately formed at the SiO2 surface, and physisorbed formic acid is formed with a delay. As Ru/SiO2 is subject to greater plasma-induced heating than SiO2 (with a surface temperature increase in the range of 70-120 degrees C, with peaks up to 150 degrees C), we observe lower amounts of physisorbed water on Ru/SiO2, and less physisorbed formic acid formation. Importantly, the formation of surface species on the catalyst sample in our plasma-catalytic setup, as well as the observed conversions and selectivities in plasma conditions, can not be explained by plasma-induced heating of the catalyst surface, but must be attributed to other plasma effects, such as the adsorption of plasma-generated radicals and molecules, or the occurrence of Eley-Rideal reactions. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000865542600001 | Publication Date | 2022-10-05 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 2044-4753; 2044-4761 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 5 | Times cited | Open Access | OpenAccess | |
Notes | Approved | Most recent IF: 5 | |||
Call Number | UA @ admin @ c:irua:191389 | Serial | 7185 | ||
Permanent link to this record | |||||
Author | Neyts, E.; Bogaerts, A.; de Meyer, M.; van Gils, S. | ||||
Title | Macroscale computer simulations to investigate the chemical vapor deposition of thin metal-oxide films | Type | A1 Journal article | ||
Year | 2007 | Publication | Surface and coatings technology | Abbreviated Journal | Surf Coat Tech |
Volume | 201 | Issue ![]() |
22/23 | Pages | 8838-8841 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | |||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Lausanne | Editor | ||
Language | Wos | 000249340400008 | Publication Date | 2007-05-02 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0257-8972; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 2.589 | Times cited | 5 | Open Access | |
Notes | Approved | Most recent IF: 2.589; 2007 IF: 1.678 | |||
Call Number | UA @ lucian @ c:irua:64790 | Serial | 1859 | ||
Permanent link to this record | |||||
Author | Lenaerts, J.; Verlinden, G.; van Vaeck, L.; Gijbels, R.; Geuens, I.; Callant, P. | ||||
Title | Exchange of fluorinated cyanine dyes between different types of silver halide microcrystals studied by imaging time-of-flight secondary ion mass spectrometry | Type | A1 Journal article | ||
Year | 2001 | Publication | Langmuir | Abbreviated Journal | Langmuir |
Volume | 17 | Issue ![]() |
23 | Pages | 7332-7338 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | |||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000172123700027 | Publication Date | 2002-07-26 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0743-7463;1520-5827; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.833 | Times cited | 8 | Open Access | |
Notes | Approved | Most recent IF: 3.833; 2001 IF: 2.963 | |||
Call Number | UA @ lucian @ c:irua:37254 | Serial | 1108 | ||
Permanent link to this record | |||||
Author | Wen, D.-Q.; Zhang, Q.-Z.; Jiang, W.; Song, U.-H.; Bogaerts, A.; Wang, Y.-N. | ||||
Title | Phase modulation in pulsed dual-frequency capacitively coupled plasmas | Type | A1 Journal article | ||
Year | 2014 | Publication | Journal of applied physics | Abbreviated Journal | J Appl Phys |
Volume | 115 | Issue ![]() |
23 | Pages | 233303 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | Particle-in-cell/Monte Carlo collision simulations, coupled with an external circuit, are used to investigate the behavior of pulsed dual-frequency (DF) capacitively coupled plasmas (CCPs). It is found that the phase shift θ between the high (or low) frequency source and the pulse modulation has a great influence on the ion density and the ionization rate. By pulsing the high frequency source, the time-averaged ion density shows a maximum when θ = 90∘. The time-averaged ion energy distribution functions (IEDFs) at the driven electrode, however, keep almost unchanged, illustrating the potential of pulsed DF-CCP for independent control of ion density (and flux) and ion energy. A detailed investigation of the temporal evolution of the plasma characteristics indicates that several high frequency harmonics can be excited at the initial stage of a pulse period by tuning the phase shift θ, and this gives rise to strong sheath oscillations, and therefore high ionization rates. For comparison, the pulsing of the low frequency source is also studied. In this case, the ion density changes slightly as a function of time, and the time-averaged ion density shows the same trend as in the HF modulation for different phase shifts θ. Moreover, the time-averaged IEDFs at the driven electrode can be modulated, showing the potential to reduce the maximum ion bombardment energy. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | American Institute of Physics | Place of Publication | New York, N.Y. | Editor | |
Language | Wos | 000338106000008 | Publication Date | 2014-06-23 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0021-8979;1089-7550; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 2.068 | Times cited | 8 | Open Access | |
Notes | Approved | Most recent IF: 2.068; 2014 IF: 2.183 | |||
Call Number | UA @ lucian @ c:irua:117415 | Serial | 2585 | ||
Permanent link to this record | |||||
Author | Kosimov, D.P.; Dzhurakhalov, A.A.; Peeters, F.M. | ||||
Title | Theoretical study of the stable states of small carbon clusters Cn (n=210) | Type | A1 Journal article | ||
Year | 2008 | Publication | Physical review : B : solid state | Abbreviated Journal | Phys Rev B |
Volume | 78 | Issue ![]() |
23 | Pages | 235433,1-235433,8 |
Keywords | A1 Journal article; Condensed Matter Theory (CMT); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | Both even- and odd-numbered neutral carbon clusters Cn (n=210) are systematically studied using the energy minimization method and the modified Brenner potential for the carbon-carbon interactions. Many stable configurations were found, and several new isomers are predicted. For the lowest energy stable configurations we obtained their binding energies and bond lengths. We found that for n5 the linear isomer is the most stable one while for n>5 the monocyclic isomer becomes the most stable. The latter was found to be regular for all studied clusters. The dependence of the binding energy for linear and cyclic clusters versus the cluster size n (n=210) is found to be in good agreement with several previous calculations, in particular with ab initio calculations as well as with experimental data for n=25. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Lancaster, Pa | Editor | ||
Language | Wos | 000262245400119 | Publication Date | 2008-12-24 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1098-0121;1550-235X; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.836 | Times cited | 35 | Open Access | |
Notes | Approved | Most recent IF: 3.836; 2008 IF: 3.322 | |||
Call Number | UA @ lucian @ c:irua:76006 | Serial | 3613 | ||
Permanent link to this record | |||||
Author | Kolev, S.; Bogaerts, A. | ||||
Title | A 2D model for a gliding arc discharge | Type | A1 Journal article | ||
Year | 2015 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 24 | Issue ![]() |
24 | Pages | 015025 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | In this study we report on a 2D fluid model of a gliding arc discharge in argon. Despite the 3D nature of the discharge, 2D models are found to be capable of providing very useful information about the operation of the discharge. We employ two modelsan axisymmetric and a Cartesian one. We show that for the considered experiment and the conditions of a low current arc (around 30 mA) in argon, there is no significant heating of the cathode surface and the discharge is sustained by field electron emission from the cathode accompanied by the formation of a cathode spot. The obtained discharge power and voltage are relatively sensitive to the surface properties and particularly to the surface roughness, causing effectively an amplification of the normal electric field. The arc body and anode region are not influenced by this and depend mainly on the current value. The gliding of the arc is modelled by means of a 2D Cartesian model. The arcelectrode contact points are analysed and the gliding mechanism along the electrode surface is discussed. Following experimental observations, the cathode spot is simulated as jumping from one point to another. A complete arc cycle is modelled from initial ignition to arc decay. The results show that there is no interaction between the successive gliding arcs. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Institute of Physics | Place of Publication | Bristol | Editor | |
Language | Wos | 000348298200026 | Publication Date | 2014-12-23 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252;1361-6595; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 34 | Open Access | |
Notes | Approved | Most recent IF: 3.302; 2015 IF: 3.591 | |||
Call Number | c:irua:122538 c:irua:122538 c:irua:122538 c:irua:122538 | Serial | 3 | ||
Permanent link to this record | |||||
Author | Cenian, A.; Chernukho, A.; Bogaerts, A.; Gijbels, R. | ||||
Title | Comment on 'Integral cross sections for electron impact excitation of electronic states of N2' | Type | Editorial | ||
Year | 2002 | Publication | Journal of physics: B : atomic and molecular physics | Abbreviated Journal | J Phys B-At Mol Opt |
Volume | 35 | Issue ![]() |
24 | Pages | 5163-5166 |
Keywords | Editorial; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | Based on the existing experimental data and their statistical errors, it is not possible to make a sound recommendation of the cross-section set of Campbell et al (J. Phys. B: At. Mol. Opt. Phys. 34 (2001) 1185). We comment on this paper. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Iop publishing ltd | Place of Publication | Bristol | Editor | |
Language | Wos | 000180629500021 | Publication Date | 2002-12-05 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0953-4075; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 1.792 | Times cited | 2 | Open Access | |
Notes | Approved | Most recent IF: 1.792; 2002 IF: 1.969 | |||
Call Number | UA @ lucian @ c:irua:40193 | Serial | 409 | ||
Permanent link to this record | |||||
Author | Peerenboom, K.; Parente, A.; Kozák, T.; Bogaerts, A.; Degrez, G. | ||||
Title | Dimension reduction of non-equilibrium plasma kinetic models using principal component analysis | Type | A1 Journal article | ||
Year | 2015 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 24 | Issue ![]() |
24 | Pages | 025004 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | The chemical complexity of non-equilibrium plasmas poses a challenge for plasma modeling because of the computational load. This paper presents a dimension reduction method for such chemically complex plasmas based on principal component analysis (PCA). PCA is used to identify a low-dimensional manifold in chemical state space that is described by a small number of parameters: the principal components. Reduction is obtained since continuity equations only need to be solved for these principal components and not for all the species. Application of the presented method to a CO2 plasma model including state-to-state vibrational kinetics of CO2 and CO demonstrates the potential of the PCA method for dimension reduction. A manifold described by only two principal components is able to predict the CO2 to CO conversion at varying ionization degrees very accurately. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Institute of Physics | Place of Publication | Bristol | Editor | |
Language | Wos | 000356816200008 | Publication Date | 2015-01-27 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252;1361-6595; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 11 | Open Access | |
Notes | Approved | Most recent IF: 3.302; 2015 IF: 3.591 | |||
Call Number | c:irua:123534 | Serial | 704 | ||
Permanent link to this record | |||||
Author | Kozák, T.; Bogaerts, A. | ||||
Title | Evaluation of the energy efficiency of CO2 conversion in microwave discharges using a reaction kinetics model | Type | A1 Journal article | ||
Year | 2015 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 24 | Issue ![]() |
24 | Pages | 015024 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | We use a zero-dimensional reaction kinetics model to simulate CO2 conversion in microwave discharges where the excitation of the vibrational levels plays a significant role in the dissociation kinetics. The model includes a description of the CO2 vibrational kinetics, taking into account state-specific VT and VV relaxation reactions and the effect of vibrational excitation on other chemical reactions. The model is used to simulate a general tubular microwave reactor, where a stream of CO2 flows through a plasma column generated by microwave radiation. We study the effects of the internal plasma parameters, namely the reduced electric field, electron density and the total specific energy input, on the CO2 conversion and its energy efficiency. We report the highest energy efficiency (up to 30%) for a specific energy input in the range 0.41.0 eV/molecule and a reduced electric field in the range 50100 Td and for high values of the electron density (an ionization degree greater than 10−5). The energy efficiency is mainly limited by the VT relaxation which contributes dominantly to the vibrational energy losses and also contributes significantly to the heating of the reacting gas. The model analysis provides useful insight into the potential and limitations of CO2 conversion in microwave discharges. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Institute of Physics | Place of Publication | Bristol | Editor | |
Language | Wos | 000348298200025 | Publication Date | 2014-12-23 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252;1361-6595; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 100 | Open Access | |
Notes | Approved | Most recent IF: 3.302; 2015 IF: 3.591 | |||
Call Number | c:irua:122243 | Serial | 1087 | ||
Permanent link to this record | |||||
Author | Lindner, H.; Murtazin, A.; Groh, S.; Niemax, K.; Bogaerts, A. | ||||
Title | Simulation and experimental studies on plasma temperature, flow velocity, and injector diameter effects for an inductively coupled plasma | Type | A1 Journal article | ||
Year | 2011 | Publication | Analytical chemistry | Abbreviated Journal | Anal Chem |
Volume | 83 | Issue ![]() |
24 | Pages | 9260-9266 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | An inductively coupled plasma (ICP) is analyzed by means of experiments and numerical simulation. Important plasma properties are analyzed, namely, the effective temperature inside the central channel and the mean flow velocity inside the plasma. Furthermore, the effect of torches with different injector diameters is studied by the model. The temperature inside the central channel is determined from the end-on collected line-to-background ratio in dependence of the injector gas flow rates. Within the limits of 3% deviation, the results of the simulation and the experiments are in good agreement in the range of flow rates relevant for the analysis of relatively large droplets, i.e., 50 μm. The deviation increases for higher gas flow rates but stays below 6% for all flow rates studied. The velocity of the gas inside the coil region was determined by side-on analyte emission measurements with single monodisperse droplet introduction and by the analysis of the injector gas path lines in the simulation. In the downstream region significantly higher velocities were found than in the upstream region in both the simulation and the experiment. The quantitative values show good agreement in the downstream region. In the upstream region, deviations were found in the absolute values which can be attributed to the flow conditions in that region and because the methods used for velocity determination are not fully consistent. Eddy structures are found in the simulated flow lines. These affect strongly the way taken by the path lines of the injector gas and they can explain the very long analytical signals found in the experiments at low flow rates. Simulations were performed for different injector diameters in order to find conditions where good analyte transport and optimum signals can be expected. The results clearly show the existence of a transition flow rate which marks the lower limit for effective analyte transport conditions through the plasma. A rule-of-thumb equation was extracted from the results from which the transition flow rate can be estimated for different injector diameters and different injector gas compositions. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Washington, D.C. | Editor | ||
Language | Wos | 000297946900013 | Publication Date | 2011-07-29 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0003-2700;1520-6882; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 6.32 | Times cited | 34 | Open Access | |
Notes | Approved | Most recent IF: 6.32; 2011 IF: 5.856 | |||
Call Number | UA @ lucian @ c:irua:94001 | Serial | 3009 | ||
Permanent link to this record | |||||
Author | Kolev, S.; Bogaerts, A. | ||||
Title | Similarities and differences between gliding glow and gliding arc discharges | Type | A1 Journal article | ||
Year | 2015 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 24 | Issue ![]() |
24 | Pages | 065023 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | In this work we have analyzed the properties of a gliding dc discharge in argon at atmospheric pressure. Despite the usual designation of these discharges as ‘gliding arc discharges’, it was found previously that they operate in two different regimes—glow and arc. Here we analyze the differences in both regimes by means of two dimensional fluid modeling. In order to address different aspects of the discharge operation, we use two models—Cartesian and axisymmetric in a cylindrical coordinate system. The obtained results show that the two types of discharges produce a similar plasma column for a similar discharge current. However, the different mechanisms of plasma channel attachment to the cathode could produce certain differences in the plasma parameters (i.e. arc elongation), and this can affect gas treatments applications. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000368117100028 | Publication Date | 2015-11-26 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252;1361-6595; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 12 | Open Access | |
Notes | This work is financially supported by the Methusalem financing and by the IAP/7 (Inter-university Attraction Pole) program ‘Physical Chemistry of Plasma-Surface Interactions’ from the Belgian Federal Office for Science Policy (BELSPO). The work was carried out in part using the Turing HPC infrastructure of the CalcUA core facility of the Universiteit Antwerpen, a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the Universiteit Antwerpen | Approved | Most recent IF: 3.302; 2015 IF: 3.591 | ||
Call Number | c:irua:129214 | Serial | 3952 | ||
Permanent link to this record | |||||
Author | Heirman, P.; Van Boxem, W.; Bogaerts, A. | ||||
Title | Reactivity and stability of plasma-generated oxygen and nitrogen species in buffered water solution: a computational study | Type | A1 Journal article | ||
Year | 2019 | Publication | Physical chemistry, chemical physics | Abbreviated Journal | Phys Chem Chem Phys |
Volume | 21 | Issue ![]() |
24 | Pages | 12881-12894 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | Plasma-treated liquids have great potential for biomedical applications. However, insight into the underlying mechanisms and the exact chemistry is still scarce. In this study, we present the combination of a 0D chemical kinetics and a 2D fluid dynamics model to investigate the plasma treatment of a buffered water solution with the kINPen (R) plasma jet. Using this model, we calculated the gas and liquid flow profiles and the transport and chemistry of all species in the gas and the liquid phase. Moreover, we evaluated the stability of the reactive oxygen and nitrogen species after plasma treatment. We found that of all species, only H2O2, HNO2/NO2-, and HNO3/NO3- are stable in the buffered solution after plasma treatment. This is because both their production and loss processes in the liquid phase are dependent on short-lived radicals (e.g. OH, NO, and NO2). Apart from some discrepancy in the absolute values of the concentrations, which can be explained by the model, all general trends and observations in our model are in qualitative agreement with experimental data and literature. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000472214000012 | Publication Date | 2019-05-29 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1463-9076; 1463-9084 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.123 | Times cited | 7 | Open Access | |
Notes | Approved | Most recent IF: 4.123 | |||
Call Number | UA @ admin @ c:irua:161314 | Serial | 6320 | ||
Permanent link to this record | |||||
Author | Bogaerts, A. | ||||
Title | Modeling plasmas in analytical chemistry—an example of cross-fertilization | Type | A1 Journal article | ||
Year | 2020 | Publication | Analytical And Bioanalytical Chemistry | Abbreviated Journal | Anal Bioanal Chem |
Volume | 412 | Issue ![]() |
24 | Pages | 6059-6083 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | This paper gives an overview of the modeling work developed in our group in the last 25 years for various plasmas used in analytical spectrochemistry, i.e., glow discharges (GDs), inductively coupled plasmas (ICPs), and laser ablation (LA) for sample introduction in the ICP and for laser-induced breakdown spectroscopy (LIBS). The modeling approaches are briefly presented, which are different for each case, and some characteristic results are illustrated. These plasmas are used not only in analytical chemistry but also in other applications, and the insights obtained in these other fields were quite helpful for us to develop models for the analytical plasmas. Likewise, there is now a huge interest in plasma–liquid interaction, atmospheric pressure glow discharges (APGDs), and dielectric barrier discharges (DBDs) for environmental, medical, and materials applications of plasmas. The insights obtained in these fields are also very relevant for ambient desorption/ionization sources and for liquid sampling, which are nowadays very popular in analytical chemistry, and they could be very helpful in developing models for these sources as well. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000522701700005 | Publication Date | 2020-03-31 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1618-2642 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.3 | Times cited | Open Access | ||
Notes | M. Aghaei, Z. Chen, D. Autrique, T. Martens, and P. Heirman are gratefully acknowledged for their valuable efforts in the model developments illustrated in this paper. | Approved | Most recent IF: 4.3; 2020 IF: 3.431 | ||
Call Number | PLASMANT @ plasmant @c:irua:168600 | Serial | 6412 | ||
Permanent link to this record | |||||
Author | Biondo, O.; van Deursen, C.F.A.M.; Hughes, A.; van de Steeg, A.; Bongers, W.; van de Sanden, M.C.M.; van Rooij, G.; Bogaerts, A. | ||||
Title | Avoiding solid carbon deposition in plasma-based dry reforming of methane | Type | A1 Journal Article | ||
Year | 2023 | Publication | Green Chemistry | Abbreviated Journal | Green Chem. |
Volume | 25 | Issue ![]() |
24 | Pages | 10485-10497 |
Keywords | A1 Journal Article; Plasma, laser ablation and surface modeling Antwerp (PLASMANT) ; | ||||
Abstract | Solid carbon deposition is a persistent challenge in dry reforming of methane (DRM), affecting both classical and plasma-based processes. In this work, we use a microwave plasma in reverse vortex flow configuration to overcome this issue in CO<sub>2</sub>/CH<sub>4</sub>plasmas. Indeed, this configuration efficiently mitigates carbon deposition, enabling operation even with pure CH<sub>4</sub>feed gas, in contrast to other configurations. At the same time, high reactor performance is achieved, with CO<sub>2</sub>and CH<sub>4</sub>conversions reaching 33% and 44% respectively, at an energy cost of 14 kJ L<sup>−1</sup>for a CO<sub>2</sub> : CH<sub>4</sub>ratio of 1 : 1. Laser scattering and optical emission imaging demonstrate that the shorter residence time in reverse vortex flow lowers the gas temperature in the discharge, facilitating a shift from full to partial CH<sub>4</sub>pyrolysis. This underscores the pivotal role of flow configuration in directing process selectivity, a crucial factor in complex chemistries like CO<sub>2</sub>/CH<sub>4</sub>mixtures and very important for industrial applications. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 001110100100001 | Publication Date | 2023-11-24 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1463-9262 | ISBN | Additional Links | UA library record; WoS full record | |
Impact Factor | 9.8 | Times cited | Open Access | ||
Notes | Universiteit Antwerpen; Nederlandse Organisatie voor Wetenschappelijk Onderzoek; HORIZON EUROPE Marie Sklodowska-Curie Actions, 813393 ; | Approved | Most recent IF: 9.8; 2023 IF: 9.125 | ||
Call Number | PLASMANT @ plasmant @c:irua:202138 | Serial | 8978 | ||
Permanent link to this record | |||||
Author | Van Laer, K.; Bogaerts, A. | ||||
Title | Fluid modelling of a packed bed dielectric barrier discharge plasma reactor | Type | A1 Journal article | ||
Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 25 | Issue ![]() |
25 | Pages | 015002 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | A packed bed dielectric barrier discharge plasma reactor is computationally studied with a fluid model. Two different complementary axisymmetric 2D geometries are used to mimic the intrinsic 3D problem. It is found that a packing enhances the electric field strength and electron temperature at the contact points of the dielectric material due to polarization of the beads by the applied potential. As a result, these contact points prove to be of direct importance to initiate the plasma. At low applied potential, the discharge stays at the contact points, and shows the properties of a Townsend discharge. When a high enough potential is applied, the plasma will be able to travel through the gaps in between the beads from wall to wall, forming a kind of glow discharge. Therefore, the inclusion of a so-called ‘channel of voids’ is indispensable in any type of packed bed modelling. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000370974800009 | Publication Date | 2015-12-01 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 50 | Open Access | |
Notes | The authors gratefully thank St Kolev for the many interesting discussions and the useful advise in setting up the models. This research was carried out in the framework of the network on Physical Chemistry of Plasma-Surface Interactions— Interuniversity Attraction Poles, phase VII (http://psi-iap7.ulb. ac.be/), and supported by the Belgian Science Policy Office (BELSPO). K Van Laer is indebted to the Institute for the Promotion of Innovation by Science and Technology in Flanders (IWT Flanders) for financial support. | Approved | Most recent IF: 3.302 | ||
Call Number | c:irua:129802 | Serial | 3982 | ||
Permanent link to this record | |||||
Author | Belov, I.; Paulussen, S.; Bogaerts, A. | ||||
Title | Appearance of a conductive carbonaceous coating in a CO2dielectric barrier discharge and its influence on the electrical properties and the conversion efficiency | Type | A1 Journal article | ||
Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 25 | Issue ![]() |
25 | Pages | 015023 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | This work examines the properties of a dielectric barrier discharge (DBD) reactor, built for CO2 decomposition, by means of electrical characterization, optical emission spectroscopy and gas chromatography. The discharge, formed in an electronegative gas (such as CO2, but also O2), exhibits clearly different electrical characteristics, depending on the surface conductivity of the reactor walls. An asymmetric current waveform is observed in the metaldielectric (MD) configuration, with sparse high-current pulses in the positive half-cycle (HC) and a more uniform regime in the negative HC. This indicates that the discharge is operating in two alternating regimes with rather different properties. At high CO2 conversion regimes, a conductive coating is deposited on the dielectric. This so-called coated MD configuration yields a symmetric current waveform, with current peaks in both the positive and negative HCs. In a double-dielectric (DD) configuration, the current waveform is also symmetric, but without current peaks in both the positive and negative HC. Finally, the DD configuration with conductive coating on the inner surface of the outer dielectric, i.e. so-called coated DD, yields again an asymmetric current waveform, with current peaks in the negative HC. These different electrical characteristics are related to the presence of the conductive coating on the dielectric wall of the reactor and can be explained by an increase of the local barrier capacitance available for charge transfer. The different discharge regimes affect the CO2 conversion, more specifically, the CO2 conversion is lowest in the clean DD configuration. It is somewhat higher in the coated DD configuration, and still higher in the MD configuration. The clean and coated MD configuration, however, gave similar CO2 conversion. These results indicate that the conductivity of the dielectric reactor walls can highly promote the development of the high-amplitude discharge current pulses and subsequently the CO2 conversion. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000370974800030 | Publication Date | 2016-01-21 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 25 | Open Access | |
Notes | The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7-PEOPLE-2013-ITN) under Grant Agreement № 606889 (RAPID—Reactive Atmospheric Plasma processIng—eDucation network). | Approved | Most recent IF: 3.302 | ||
Call Number | c:irua:130790 | Serial | 4006 | ||
Permanent link to this record | |||||
Author | Ozkan, A.; Dufour, T.; Silva, T.; Britun, N.; Snyders, R.; Bogaerts, A.; Reniers, F. | ||||
Title | The influence of power and frequency on the filamentary behavior of a flowing DBD—application to the splitting of CO2 | Type | A1 Journal article | ||
Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 25 | Issue ![]() |
25 | Pages | 025013 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | In this experimental study, a flowing dielectric barrier discharge operating at atmospheric pressure is used for the splitting of CO2 into O2 and CO. The influence of the applied frequency and plasma power on the microdischarge properties is investigated to understand their role on the CO2 conversion. Electrical measurements are carried out to explain the conversion trends and to characterize the microdischarges through their number, their lifetime, their intensity and the induced electrical charge. Their influence on the gas and electrode temperatures is also evidenced through optical emission spectroscopy and infrared imaging. It is shown that, in our configuration, the conversion depends mostly on the charge delivered in the plasma and not on the effective plasma voltage when the applied power is modified. Similarly, at constant total current, a better conversion is observed at low frequencies, where a less filamentary discharge regime with a higher effective plasma voltage than that at a higher frequency is obtained. |
||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000372337900015 | Publication Date | 2016-02-25 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 40 | Open Access | |
Notes | The authors acknowledge financial support from the IAPVII/ 12, P7/34 (Inter-university Attraction Pole) program ‘PSI-Physical Chemistry of Plasma-Surface Interactions’, financially supported by the Belgian Federal Office for Science Policy (BELSPO). A Ozkan would like to thank the financial support given by ‘Fonds David et Alice Van Buuren’. N Britun is a postdoctoral researcher of the F.R.S.-FNRS, Belgium. | Approved | Most recent IF: 3.302 | ||
Call Number | c:irua:131904 | Serial | 4021 | ||
Permanent link to this record | |||||
Author | Trenchev, G.; Kolev, S.; Bogaerts, A. | ||||
Title | A 3D model of a reverse vortex flow gliding arc reactor | Type | A1 Journal article | ||
Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 25 | Issue ![]() |
25 | Pages | 035014 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | In this computational study, a gliding arc plasma reactor with a reverse-vortex flow stabilization is modelled for the first time by a fluid plasma description. The plasma reactor operates with argon gas at atmospheric pressure. The gas flow is simulated using the k-ε Reynolds-averaged Navier–Stokes turbulent model. A quasi-neutral fluid plasma model is used for computing the plasma properties. The plasma arc movement in the reactor is observed, and the results for the gas flow, electrical characteristics, plasma density, electron temperature, and gas temperature are analyzed. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000376557400022 | Publication Date | 2016-04-09 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 20 | Open Access | |
Notes | This research was carried out in the framework of the network on Physical Chemistry of Plasma–Surface Interactions— Interuniversity Attraction Poles, phase VII (http://psi-iap7.ulb. ac.be/), and supported by the Belgian Science Policy Office (BELSPO), and it was also funded by the Fund for Scientific Research Flanders (FWO). Grant number: 11U5316N. | Approved | Most recent IF: 3.302 | ||
Call Number | c:irua:132888 c:irua:132888 | Serial | 4063 | ||
Permanent link to this record | |||||
Author | Ozkan, A.; Dufour, T.; Bogaerts, A.; Reniers, F. | ||||
Title | How do the barrier thickness and dielectric material influence the filamentary mode and CO2conversion in a flowing DBD? | Type | A1 Journal article | ||
Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 25 | Issue ![]() |
25 | Pages | 045016 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | Dielectric barrier discharges (DBDs) are commonly used to generate cold plasmas at atmospheric pressure. Whatever their configuration (tubular or planar), the presence of a dielectric barrier is mandatory to prevent too much charge build up in the plasma and the formation of a thermal arc. In this article, the role of the barrier thickness (2.0, 2.4 and 2.8 mm) and of the kind of dielectric material (alumina, mullite, pyrex, quartz) is investigated on the filamentary behavior in the plasma and on the CO2 conversion in a tubular flowing DBD, by means of mass spectrometry measurements correlated with electrical characterization and IR imaging. Increasing the barrier thickness decreases the capacitance, while preserving the electrical charge. As a result, the voltage over the dielectric increases and a larger number of microdischarges is generated, which enhances the CO2 conversion. Furthermore, changing the dielectric material of the barrier, while keeping the same geometry and dimensions, also affects the CO2 conversion. The highest CO2 conversion and energy efficiency are obtained for quartz and alumina, thus not following the trend of the relative permittivity. From the electrical characterization, we clearly demonstrate that the most important parameters are the somewhat higher effective plasma voltage (yielding a somewhat higher electric field and electron energy in the plasma) for quartz, as well as the higher plasma current (and thus larger electron density) and the larger number of microdischarge filaments (mainly for alumina, but also for quartz). The latter could be correlated to the higher surface roughness for alumina and to the higher voltage over the dielectric for quartz. |
||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000380380200030 | Publication Date | 2016-06-30 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 24 | Open Access | |
Notes | The authors acknowledge financial support from the IAPVII/ 12, P7/34 (Inter-university Attraction Pole) program ‘PSI-Physical Chemistry of Plasma-Surface Interactions’, financially supported by the Belgian Federal Office for Science Policy (BELSPO). A. Ozkan would like to thank the financial support given by ‘Fonds David et Alice Van Buuren’. | Approved | Most recent IF: 3.302 | ||
Call Number | c:irua:134396 | Serial | 4100 | ||
Permanent link to this record | |||||
Author | Berthelot, A.; Bogaerts, A. | ||||
Title | Modeling of plasma-based CO2conversion: lumping of the vibrational levels | Type | A1 Journal article | ||
Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 25 | Issue ![]() |
25 | Pages | 045022 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | Although CO2 conversion by plasma technology is gaining increasing interest, the underlying mechanisms for an energy-efficient process are still far from understood. In this work, a reduced non-equilibrium CO2 plasma chemistry set, based on level lumping of the vibrational levels, is proposed and the reliability of this level-lumping method is tested by a self-consistent zero-dimensional code. A severe reduction of the number of equations to be solved is achieved, which is crucial to be able to model non-equilibrium CO2 plasmas by 2-dimensional models. Typical conditions of pressure and power used in a microwave plasma for CO2 conversion are investigated. Several different sets, using different numbers of lumped groups, are considered. The lumped models with 1, 2 or 3 groups are able to reproduce the gas temperature, electron density and electron temperature profiles, as calculated by the full model treating all individual excited levels, in the entire pressure range investigated. Furthermore, a 3-groups model is also able to reproduce the shape of the vibrational distribution function (VDF) and gives the most reliable prediction of the CO2 conversion. A strong influence of the vibrational excitation on the plasma characteristics is observed. Finally, the limitations of the lumped-levels method are discussed. |
||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000380380200036 | Publication Date | 2016-07-08 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 33 | Open Access | |
Notes | This project has received funding from the European Union’s Seventh Framework Programme for research, technological development and demonstration under grant agreement no 606889 and it was also carried out in the framework of the network on Physical Chemistry of Plasma-Surface Interactions—Interuniversity Attraction Poles, phase VII (PSI-IAP7) supported by the Belgian Science Policy Office (BELSPO). The computational work was carried out using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UA), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UA. | Approved | Most recent IF: 3.302 | ||
Call Number | c:irua:134397 | Serial | 4101 | ||
Permanent link to this record | |||||
Author | Ozkan, A.; Dufour, T.; Silva, T.; Britun, N.; Snyders, R.; Reniers, F.; Bogaerts, A. | ||||
Title | DBD in burst mode: solution for more efficient CO2conversion? | Type | A1 Journal article | ||
Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 25 | Issue ![]() |
25 | Pages | 055005 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | CO2 conversion into value-added products has gained significant interest over the few last years, as the greenhouse gas concentrations constantly increase due to anthropogenic activities. Here we report on experiments for CO2 conversion by means of a cold atmospheric plasma using a cylindrical flowing dielectric barrier discharge (DBD) reactor. A detailed comparison of this DBD ignited in a so-called burst mode (i.e. where an AC voltage is applied during a limited amount of time) and pure AC mode is carried out to evaluate their effect on the conversion of CO2 as well as on the energy efficiency. Decreasing the duty cycle in the burst mode from 100% (i.e. corresponding to pure AC mode) to 40% leads to a rise in the conversion from 16–26% and to a rise in the energy efficiency from 15 to 23%. Based on a detailed electrical analysis, we show that the conversion correlates with the features of the microfilaments. Moreover, the root-mean-square voltage in the burst mode remains constant as a function of the process time for the duty cycles <70%, while a higher duty cycle or the usual pure AC mode leads to a clear voltage decay by more than 500 V, over approximately 90 s, before reaching a steady state regime. The higher plasma voltage in the burst mode yields a higher electric field. This causes the increasing the electron energy, and therefore their involvement in the CO2 dissociation process, which is an additional explanation for the higher CO2 conversion and energy efficiency in the burst mode. |
||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000403945500005 | Publication Date | 2016-08-02 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 17 | Open Access | |
Notes | The authors acknowledge financial support from the IAPVII/ 12, P7/34 (Inter-university Attraction Pole) program ‘PSI-Physical Chemistry of Plasma-Surface Interactions’, financially supported by the Belgian Federal Office for Science Policy (BELSPO). A. Ozkan would also like to thank financial support given by ‘Fonds David et Alice Van Buuren’. | Approved | Most recent IF: 3.302 | ||
Call Number | c:irua:134841 | Serial | 4107 | ||
Permanent link to this record | |||||
Author | Bogaerts, A.; Wang, W.; Berthelot, A.; Guerra, V. | ||||
Title | Modeling plasma-based CO2conversion: crucial role of the dissociation cross section | Type | A1 Journal article | ||
Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 25 | Issue ![]() |
25 | Pages | 055016 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | Plasma-based CO2 conversion is gaining increasing interest worldwide. A large research effort is devoted to improving the energy efficiency. For this purpose, it is very important to understand the underlying mechanisms of the CO2 conversion. The latter can be obtained by computer modeling, describing in detail the behavior of the various plasma species and all relevant chemical processes. However, the accuracy of the modeling results critically depends on the accuracy of the assumed input data, like cross sections. This is especially true for the cross section of electron impact dissociation, as the latter process is believed to proceed through electron impact excitation, but it is not clear from the literature which excitation channels effectively lead to dissociation. Therefore, the present paper discusses the effect of different electron impact dissociation cross sections reported in the literature on the calculated CO2 conversion, for a dielectric barrier discharge (DBD) and a microwave (MW) plasma. Comparison is made to experimental data for the DBD case, to elucidate which cross section might be the most realistic. This comparison reveals that the cross sections proposed by Itikawa and by Polak and Slovetsky both seem to underestimate the CO2 conversion. The cross sections recommended by Phelps with thresholds of 7 eV and 10.5 eV yield a CO2 conversion only slightly lower than the experimental data, but the sum of both cross sections overestimates the values, indicating that these cross sections represent dissociation, but most probably also include other (pure excitation) channels. Our calculations indicate that the choice of the electron impact dissociation cross section is crucial for the DBD, where this process is the dominant mechanism for CO2 conversion. In the MW plasma, it is only significant at pressures up to 100 mbar, while it is of minor importance for higher pressures, when dissociation proceeds mainly through collisions of CO2 with heavy particles. |
||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000384030600001 | Publication Date | 2016-08-31 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 57 | Open Access | |
Notes | The authors would like to thank R Snoeckx and S Heijkers for the interesting discussions. This research was supported by the European Union’s Seventh Framework Programme for research, technological development and demonstration under grant agreement no. 606889, the European Marie Skłodowska-Curie Individual Fellowship project ‘GlidArc’ within Horizon2020, the FWO project (grant G.0383.16N), and the Network on Physical Chemistry of Plasma-Surface Interactions—Interuniversity Attraction Poles, phase VII (PSI-IAP7), supported by the Belgian Science Policy Office (BELSPO). The computational work was carried out using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UA), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UA. VG was partially supported by the Portuguese FCT— Fundação para a Ci | Approved | Most recent IF: 3.302 | ||
Call Number | c:irua:135070 | Serial | 4111 | ||
Permanent link to this record | |||||
Author | Wang, W.; Bogaerts, A. | ||||
Title | Effective ionisation coefficients and critical breakdown electric field of CO2at elevated temperature: effect of excited states and ion kinetics | Type | A1 Journal article | ||
Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 25 | Issue ![]() |
25 | Pages | 055025 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | Electrical breakdown by the application of an electric field occurs more easily in hot gases than in cold gases because of the extra electron-species interactions that occur as a result of dissociation, ionization and excitation at higher temperature. This paper discusses some overlooked physics and clarifies inaccuracies in the evaluation of the effective ionization coefficients and the critical reduced breakdown electric field of CO2 at elevated temperature, considering the influence of excited states and ion kinetics. The critical reduced breakdown electric field is obtained by balancing electron generation and loss mechanisms using the electron energy distribution function (EEDF) derived from the Boltzmann transport equation under the two-term approximation. The equilibrium compositions of the hot gas mixtures are determined based on Gibbs free energy minimization considering the ground states as well as vibrationally and electronically excited states as independent species, which follow a Boltzmann distribution with a fixed excitation temperature. The interaction cross sections between electrons and the excited species, not reported previously, are properly taken into account. Furthermore, the ion kinetics, including electron–ion recombination, associative electron detachment, charge transfer and ion conversion into stable negative ion clusters, are also considered. Our results indicate that the excited species lead to a greater population of high-energy electrons at higher gas temperature and this affects the Townsend rate coefficients (i.e. of electron impact ionization and attachment), but the critical reduced breakdown electric field strength of CO2 is only affected when also properly accounting for the ion kinetics. Indeed, the latter greatly influences the effective ionization coefficients and hence the critical reduced breakdown electric field at temperatures above 1500 K. The rapid increase of the dissociative electron attachment cross-section of molecular oxygen with rising vibrational quantum number leads to a larger electron loss rate and this enhances the critical reduced breakdown electric field strength in the temperature range where the concentration of molecular oxygen is relatively high. The results obtained in this work show reasonable agreement with experimental results from literature, and are important for the evaluation of the dielectric strength of CO2 in a highly reactive environment at elevated temperature. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000385494000006 | Publication Date | 2016-09-22 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 3 | Open Access | |
Notes | Skłodowska-Curie Individual Fellowship ‘GlidArc’ within Horizon2020 (Grant No.657304) and the FWO project (grant G.0383.16N). The computational work was carried out using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UA), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UA. | Approved | Most recent IF: 3.302 | ||
Call Number | PLASMANT @ plasmant @ c:irua:135515 | Serial | 4281 | ||
Permanent link to this record | |||||
Author | Wang, W.; Berthelot, A.; Kolev, S.; Tu, X.; Bogaerts, A. | ||||
Title | CO2 conversion in a gliding arc plasma: 1D cylindrical discharge model | Type | A1 Journal article | ||
Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 25 | Issue ![]() |
25 | Pages | 065012 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | CO 2 conversion by a gliding arc plasma is gaining increasing interest, but the underlying mechanisms for an energy-efficient process are still far from understood. Indeed, the chemical complexity of the non-equilibrium plasma poses a challenge for plasma modeling due to the huge computational load. In this paper, a one-dimensional (1D) gliding arc model is developed in a cylindrical frame, with a detailed non-equilibrium CO 2 plasma chemistry set, including the CO 2 vibrational kinetics up to the dissociation limit. The model solves a set of time- dependent continuity equations based on the chemical reactions, as well as the electron energy balance equation, and it assumes quasi-neutrality in the plasma. The loss of plasma species and heat due to convection by the transverse gas flow is accounted for by using a characteristic frequency of convective cooling, which depends on the gliding arc radius, the relative velocity of the gas flow with respect to the arc and on the arc elongation rate. The calculated values for plasma density and plasma temperature within this work are comparable with experimental data on gliding arc plasma reactors in the literature. Our calculation results indicate that excitation to the vibrational levels promotes efficient dissociation in the gliding arc, and this is consistent with experimental investigations of the gliding arc based CO 2 conversion in the literature. Additionally, the dissociation of CO 2 through collisions with O atoms has the largest contribution to CO 2 splitting under the conditions studied. In addition to the above results, we also demonstrate that lumping the CO 2 vibrational states can bring a significant reduction of the computational load. The latter opens up the way for 2D or 3D models with an accurate description of the CO 2 vibrational kinetics. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000386605100002 | Publication Date | 2016-10-18 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 3 | Open Access | |
Notes | This research was supported by the European Marie Skłodowska-Curie Individual Fellowship ‘GlidArc’ within Horizon2020 (Grant No. 657304) and by the FWO project (grant G.0383.16N). The calculations were performed using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UAntwerpen), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UAntwerpen. | Approved | Most recent IF: 3.302 | ||
Call Number | PLASMANT @ plasmant @ c:irua:135990 | Serial | 4286 | ||
Permanent link to this record | |||||
Author | de de Meux, A.J.; Pourtois, G.; Genoe, J.; Heremans, P. | ||||
Title | Origin of the apparent delocalization of the conduction band in a high-mobility amorphous semiconductor | Type | A1 Journal article | ||
Year | 2017 | Publication | Journal of physics : condensed matter | Abbreviated Journal | J Phys-Condens Mat |
Volume | 29 | Issue ![]() |
25 | Pages | 255702 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | In this paper, we show that the apparent delocalization of the conduction band reported from first-principles simulations for the high-mobility amorphous oxide semiconductor InGaZnO4 (a-IGZO) is an artifact induced by the periodic conditions imposed to the model. Given a sufficiently large unit-cell dimension (over 40 angstrom), the conduction band becomes localized. Such a model size is up to four times the size of commonly used models for the study of a-IGZO. This finding challenges the analyses done so far on the nature of the defects and on the interpretation of numerous electrical measurements. In particular, we re-interpret the meaning of the computed effective mass reported so far in literature. Our finding also applies to materials such as SiZnSnO, ZnSnO, InZnSnO, In2O3 or InAlZnO4 whose models have been reported to display a fully delocalized conduction band in the amorphous phase. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | London | Editor | ||
Language | Wos | 000402434900002 | Publication Date | 2017-02-15 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0953-8984 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 2.649 | Times cited | 5 | Open Access | Not_Open_Access |
Notes | Approved | Most recent IF: 2.649 | |||
Call Number | UA @ lucian @ c:irua:144183 | Serial | 4676 | ||
Permanent link to this record | |||||
Author | Kumar, N.; Attri, P.; Dewilde, S.; Bogaerts, A. | ||||
Title | Inactivation of human pancreatic ductal adenocarcinoma with atmospheric plasma treated media and water: a comparative study | Type | A1 Journal article | ||
Year | 2018 | Publication | Journal of physics: D: applied physics | Abbreviated Journal | J Phys D Appl Phys |
Volume | 51 | Issue ![]() |
25 | Pages | 255401 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | In recent years, the interest in treating cancer cells with plasma treated media (PTM) and plasma treated water (PTW) has increased tremendously. However, the actions of PTM and PTW are still not entirely understood. For instance, it is not clear whether the action of PTM is due to a modification in proteins/amino acids after plasma treatment of the media, or due to reactive oxygen and nitrogen species (RONS) generated from the plasma, or a combination of both effects. To differentiate between the actions of RONS and modified proteins/amino acids on the treatment of cancer cells, we compared the effects of PTM and PTW on two different pancreatic ductal adenocarcinomas (MiaPaca-2, BxPc3) and pancreatic stellate cells (PSCs) (hPSC128-SV). PSCs closely interact with cancer cells to create a tumor-promoting environment that stimulates local tumor progression and metastasis. We treated culture media and deionized water with a cold atmospheric plasma (CAP) jet, and subsequently applied this PTM/PTW at various ratios to the pancreatic cancer and PSC cell lines. We evaluated cell death, intracellular ROS concentrations and the mRNA expression profiles of four oxidative stress-related genes, i.e. Mitogen-activated protein kinase 7 (MAPK7), B-cell lymphoma 2 (BCL2), Checkpoint kinase 1 (CHEK1) and DNA damage-inducible transcript 3, also known as C/EBP homologous protein (CHOP). Our findings demonstrate that PTM and PTW have a similar efficacy to kill pancreatic cancer cells, while PTW is slightly more effective in killing PSCs, as compared to PTM. Furthermore, we observed an enhancement of the intracellular ROS concentrations in both pancreatic cancer cells and PSCs. Thus, it is likely that under our experimental conditions, the anti-cancer activity of PTM can be attributed more to the RONS present in the treated liquid, than to the modification of proteins/amino acids in the media. Furthermore, the fact that the chemo-resistant PSCs were killed by PTM/PTW may offer possibilities for new anti-cancer therapies for pancreatic cancer cells, including PSCs. |
||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000434266900001 | Publication Date | 2018-06-04 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0022-3727 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 2.588 | Times cited | 6 | Open Access | OpenAccess |
Notes | We gratefully acknowledge financial support from the Research Foundation—Flanders (FWO) (grant number 12J5617N) and from the European Marie Skłodowska–Curie Individual Fellowship ‘Anticancer-PAM’ within Horizon2020 (grant number 743546). We also thank Atsushi Masamune (Division of Gastroenterology, Tohoku University Graduate School of Medicine, Sendai, Miyagi Prefecture, Japan) for providing us with human PSCs (hPSC128-SV) for this study. | Approved | Most recent IF: 2.588 | ||
Call Number | PLASMANT @ plasmant @c:irua:151962 | Serial | 4997 | ||
Permanent link to this record | |||||
Author | Brault, P.; Neyts, E.C. | ||||
Title | Molecular dynamics simulations of supported metal nanocatalyst formation by plasma sputtering | Type | A1 Journal article | ||
Year | 2015 | Publication | Catalysis today | Abbreviated Journal | Catal Today |
Volume | 256 | Issue ![]() |
256 | Pages | 3-12 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | Magnetron sputtering is a widely used physical vapor deposition technique for deposition and formation of nanocatalyst thin films and clusters. Nevertheless, so far only few studies investigated this formation process at the fundamental level. We here review atomic scale molecular dynamics simulations aimed at elucidating the nanocatalyst growth process through magnetron sputtering. We first introduce the basic magnetron sputtering background and machinery of molecular dynamics simulations, and then describe the studies conducted in this field so far. We also present a perspective view on how the field may be developed further. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Amsterdam | Editor | ||
Language | Wos | 000360085300002 | Publication Date | 2015-02-28 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0920-5861; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.636 | Times cited | 18 | Open Access | |
Notes | Approved | Most recent IF: 4.636; 2015 IF: 3.893 | |||
Call Number | c:irua:127408 | Serial | 2174 | ||
Permanent link to this record | |||||
Author | Neyts, E.C.; Ostrikov, K.(K.) | ||||
Title | Nanoscale thermodynamic aspects of plasma catalysis | Type | A1 Journal article | ||
Year | 2015 | Publication | Catalysis today | Abbreviated Journal | Catal Today |
Volume | 256 | Issue ![]() |
256 | Pages | 23-28 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | Plasma catalysis continues to gain increasing scientific interest, both in established fields like toxic waste abatement and emerging fields like greenhouse gas conversion into value-added chemicals. Attention is typically focused on the obtained conversion process selectivity, rates and energy efficiency. Much less attention is usually paid to the underlying mechanistic aspects of the processes that occur. In this contribution, we critically examine a number of fundamentally important nanoscale thermodynamic aspects of plasma catalysis, which are very relevant to these processes but so far have been overlooked or insufficiently covered in the plasma catalysis literature. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Amsterdam | Editor | ||
Language | Wos | 000360085300004 | Publication Date | 2015-03-25 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0920-5861; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.636 | Times cited | 14 | Open Access | |
Notes | Approved | Most recent IF: 4.636; 2015 IF: 3.893 | |||
Call Number | c:irua:127409 | Serial | 2274 | ||
Permanent link to this record | |||||
Author | Nozaki, T.; Neyts, E.C.; Sankaran, M.; Ostrikov, K.(K.); Liu, C.-J. | ||||
Title | Plasmas for enhanced catalytic processes (ISPCEM 2014) | Type | Editorial | ||
Year | 2015 | Publication | Catalysis today | Abbreviated Journal | Catal Today |
Volume | 256 | Issue ![]() |
256 | Pages | 1-2 |
Keywords | Editorial; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | |||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Amsterdam | Editor | ||
Language | Wos | 000360085300001 | Publication Date | 2015-08-21 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0920-5861; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.636 | Times cited | 2 | Open Access | |
Notes | Approved | Most recent IF: 4.636; 2015 IF: 3.893 | |||
Call Number | c:irua:127407 | Serial | 2641 | ||
Permanent link to this record | |||||
Author | Sun, S.R.; Kolev, S.; Wang, H.X.; Bogaerts, A. | ||||
Title | Coupled gas flow-plasma model for a gliding arc: investigations of the back-breakdown phenomenon and its effect on the gliding arc characteristics | Type | A1 Journal article | ||
Year | 2017 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
Volume | 26 | Issue ![]() |
26 | Pages | 015003 |
Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | We present a 3D and 2D Cartesian quasi-neutral plasma model for a low current argon gliding arc discharge, including strong interactions between the gas flow and arc plasma column. The 3D model is applied only for a short time of 0.2 ms due to its huge computational cost. It mainly serves to verify the reliability of the 2D model. As the results in 2D compare well with those in 3D, they can be used for a better understanding of the gliding arc basic characteristics. More specifically, we investigate the back-breakdown phenomenon induced by an artificially controlled plasma channel, and we discuss its effect on the gliding arc characteristics. The back-breakdown phenomenon, or backward-jump motion of the arc, as observed in the experiments, results in a drop of the gas temperature, as well as in a delay of the arc velocity with respect to the gas flow velocity, allowing more gas to pass through the arc, and thus increasing the efficiency of the gliding arc for gas treatment applications. |
||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000419253000001 | Publication Date | 2016-11-22 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.302 | Times cited | 9 | Open Access | OpenAccess |
Notes | This work is financially supported by the Methusalem financing, by the Fund for Scientific Research Flanders (FWO) and by the IAP/7 (Inter-university Attraction Pole) program ‘Physical Chemistry of Plasma-Surface Interactions’ from the Belgian Federal Office for Science Policy (BELSPO). The work was carried out in part using the Turing HPC infrastructure of the CalcUA core facility of the Universiteit Antwerpen, a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the Universiteit Antwerpen. This work was also supported by the National Natural Science Foundation of China (Grant Nos. 11275021, 11575019). S R Sun thanks the financial support from the China Scholarship Council. | Approved | Most recent IF: 3.302 | ||
Call Number | PLASMANT @ plasmant @ c:irua:138993 | Serial | 4337 | ||
Permanent link to this record |