| |
Records |
Links |
|
Author |
Bizindavyi, J.; Verhulst, A.S.; Smets, Q.; Verreck, D.; Sorée, B.; Groeseneken, G. |
|
| |
Title |
Band-Tails Tunneling Resolving the Theory-Experiment Discrepancy in Esaki Diodes |
Type |
A1 Journal article |
| |
Year |
2018 |
Publication |
IEEE journal of the Electron Devices Society |
Abbreviated Journal |
Ieee J Electron Devi |
|
| |
Volume |
6 |
Issue |
1 |
Pages |
633-641 |
|
| |
Keywords |
A1 Journal article; Condensed Matter Theory (CMT) |
|
| |
Abstract  |
Discrepancies exist between the theoretically predicted and experimentally measured performance of band-to-band tunneling devices, such as Esaki diodes and tunnel field-effect transistors (TFETs). We resolve this discrepancy for highly-doped, direct-bandgap Esaki diodes by successfully calibrating a semi-classical model for high-doping-induced ballistic band-tails tunneling currents at multiple temperatures with two In0.53Ga0.47As Esaki diodes using their SIMS doping profiles, C-V characteristics and their forward-bias current density in the negative differential resistance (NDR) regime. The current swing in the NDR regime is shown not to be linked to the band-tails Urbach energy. We further demonstrate theoretically that the calibrated band-tails contribution is also the dominant band-tails contribution to the subthreshold swing of the corresponding TFETs. Lastly, we verify that the presented procedure is applicable to all direct-bandgap semiconductors by successfully applying it to InAs Esaki diodes in literature. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
IEEE, Electron Devices Society |
Place of Publication |
New York, N.Y. |
Editor |
|
|
| |
Language |
|
Wos |
000435505000013 |
Publication Date |
2018-05-15 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
2168-6734 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
3.141 |
Times cited |
5 |
Open Access |
|
|
| |
Notes |
; J. Bizindavyi gratefully acknowledges FWO-Vlaanderen for a Strategic Basic Research PhD fellowship. ; |
Approved |
Most recent IF: 3.141 |
|
| |
Call Number |
UA @ lucian @ c:irua:152097UA @ admin @ c:irua:152097 |
Serial |
5014 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Bals, S.; Batenburg, K.J.; Liang, D.; Lebedev, O.; Van Tendeloo, G.; Aerts, A.; Martens, J.A.; Kirschhock, C.E. |
|
| |
Title |
Quantitative three-dimensional modeling of zeotile through discrete electron tomography |
Type |
A1 Journal article |
| |
Year |
2009 |
Publication |
Journal of the American Chemical Society |
Abbreviated Journal |
J Am Chem Soc |
|
| |
Volume |
131 |
Issue |
13 |
Pages |
4769-4773 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT); Vision lab |
|
| |
Abstract |
Discrete electron tomography is a new approach for three-dimensional reconstruction of nanoscale objects. The technique exploits prior knowledge of the object to be reconstructed, which results in an improvement of the quality of the reconstructions. Through the combination of conventional transmission electron microscopy and discrete electron tomography with a model-based approach, quantitative structure determination becomes possible. In the present work, this approach is used to unravel the building scheme of Zeotile-4, a silica material with two levels of structural order. The layer sequence of slab-shaped building units could be identified. Successive layers were found to be related by a rotation of 120°, resulting in a hexagonal space group. The Zeotile-4 material is a demonstration of the concept of successive structuring of silica at two levels. At the first level, the colloid chemical properties of Silicalite-1 precursors are exploited to create building units with a slablike geometry. At the second level, the slablike units are tiled using a triblock copolymer to serve as a mesoscale structuring agent. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
Washington, D.C. |
Editor |
|
|
| |
Language |
|
Wos |
000264806300050 |
Publication Date |
2009-03-16 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0002-7863;1520-5126; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
13.858 |
Times cited |
58 |
Open Access |
|
|
| |
Notes |
Fwo; Iap; Esteem 026019 |
Approved |
Most recent IF: 13.858; 2009 IF: 8.580 |
|
| |
Call Number |
UA @ lucian @ c:irua:76393 |
Serial |
2767 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Haug, C.; Ruebeling, F.; Kashiwar, A.; Gumbsch, P.; Kübel, C.; Greiner, C. |
|
| |
Title |
Early deformation mechanisms in the shear affected region underneath a copper sliding contact |
Type |
A1 Journal article |
| |
Year |
2020 |
Publication |
Nature Communications |
Abbreviated Journal |
Nat Commun |
|
| |
Volume |
11 |
Issue |
1 |
Pages |
839-8 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
Dislocation mediated plastic deformation decisively influences the friction coefficient and the microstructural changes at many metal sliding interfaces during tribological loading. This work explores the initiation of a tribologically induced microstructure in the vicinity of a copper twin boundary. Two distinct horizontal dislocation traces lines (DTL) are observed in their interaction with the twin boundary beneath the sliding interface. DTL formation seems unaffected by the presence of the twin boundary but the twin boundary acts as an indicator of the occurring deformation mechanisms. Three concurrent elementary processes can be identified: simple shear of the subsurface area in sliding direction, localized shear at the primary DTL and crystal rotation in the layers above and between the DTLs around axes parallel to the transverse direction. Crystal orientation analysis demonstrates a strong compatibility of these proposed processes. Quantitatively separating these different deformation mechanisms is crucial for future predictive modeling of tribological contacts. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
|
Publication Date |
2020-02-11 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
2041-1723 |
ISBN |
|
Additional Links |
UA library record |
|
| |
Impact Factor |
16.6 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 16.6; 2020 IF: 12.124 |
|
| |
Call Number |
UA @ admin @ c:irua:183619 |
Serial |
6863 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Idrissi, H.; Cordier, P.; Jacob, D.; Walte, N. |
|
| |
Title |
Dislocations and plasticity of experimentally deformed coesite |
Type |
A1 Journal article |
| |
Year |
2008 |
Publication |
European journal of mineralogy |
Abbreviated Journal |
Eur J Mineral |
|
| |
Volume |
20 |
Issue |
4 |
Pages |
665-671 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
Dislocation microstructures have been characterized by transmission electron microscopy in polycrystalline coesite deformed experimentally at 4 GPa, 1200 degrees C. Burgers vectors have been determined by large-angle convergent-beam electron diffraction. Sample orientation was assisted by precession electron diffraction to overcome difficulties arising from pseudo-hexagonal symmetry. The results are explained by using a pseudo-hexagonal setting. We found that most dislocations observed are of the 1/3 < 2 (1) over bar(1) over bar0 > type. No clear glide plane was identified, suggesting that climb is activated under these conditions. This conclusion is supported by the observation of numerous subgrain boundaries. We have also observed some [00011 dislocations. Finally, the C12/cl space group to which coesite belongs being centred, an additional slip system is observed: 1/6[(1) over bar2 (1) over bar3](01 (1) over bar1) (1/2[(1) over bar 10](110) in the monoclinic setting). |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
Stuttgart |
Editor |
|
|
| |
Language |
|
Wos |
000262891900021 |
Publication Date |
2008-08-29 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0935-1221; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
1.362 |
Times cited |
5 |
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 1.362; 2008 IF: 1.220 |
|
| |
Call Number |
UA @ lucian @ c:irua:94604 |
Serial |
733 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Wu, Y.; Chen, G.; Yu, J.; Wang, D.; Ma, C.; Li, C.; Pennycook, S.J.; Yan, Y.; Wei, S.-H. |
|
| |
Title |
Hole-induced spontaneous mutual annihilation of dislocation pairs |
Type |
A1 Journal article |
| |
Year |
2019 |
Publication |
The journal of physical chemistry letters |
Abbreviated Journal |
J Phys Chem Lett |
|
| |
Volume |
10 |
Issue |
23 |
Pages |
7421-7425 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
Dislocations are always observed during crystal growth, and it is usually desirable to reduce the dislocation density in high-quality crystals. Here, the annihilation process of the 30 degrees Shockley partial dislocation pairs in CdTe is studied by first-principles calculations. We found that the dislocations can glide relatively easily due to the weak local bonding. Our systematic study of the slipping mechanism of the dislocations suggests that the energy barrier for the annihilation process is low. Band structure calculations reveal that the band bending caused by the charge transfer between the two dislocation cores depends on the core-core distance. A simple linear model is proposed to describe the mechanism of formation of the dislocation pair. More importantly, we demonstrate that hole injection can affect the core structure, increase the mobility, and eventually trigger a spontaneous mutual annihilation, which could be employed as a possible facile way to reduce the dislocation density. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000501622700017 |
Publication Date |
2019-11-17 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1948-7185 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
9.353 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 9.353 |
|
| |
Call Number |
UA @ admin @ c:irua:165068 |
Serial |
6302 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Vanschoenwinkel, J.; Lizin, S.; Swinnen, G.; Azadi, H.; Van Passel, S. |
|
| |
Title |
Solar cooking in Senegalese villages : an application of best-worst scaling |
Type |
A1 Journal article |
| |
Year |
2014 |
Publication |
Energy Policy |
Abbreviated Journal |
Energ Policy |
|
| |
Volume |
67 |
Issue |
|
Pages |
447-458 |
|
| |
Keywords |
A1 Journal article; Sociology; Engineering sciences. Technology; Engineering Management (ENM) |
|
| |
Abstract |
Dissemination programs of nontraditional cookstoves often fail. Nontraditional cookstoves aim to solve problems associated with biomass fuel usage in developing countries. Recent studies do not explain what drives user's cookstove choice. This study therefore builds a holistic framework that centralizes product-specific preferences or needs. The case study identifies product-specific factors that influence rural Senegalese inhabitants to switch to solar cooking, using best worst scaling. Looking at the preferences, the case study classified 126 respondents, in three distinct market segments with different solar cooking expectations. The paper identifies socio-demographic characteristics that explain these differences in the respondents' preferences. Finally, the respondent sample is divided in two groups: solar cooker owners and non-owners. When studied with regard to the same issue, solar cooker owners appear to value benefits of the solar cooker lower than non-owners. This is due to program factors (such as formations, after-sales network) and miscommunication (such as a wrong image of the solar cooker) that highly influenced the respondents' cookstove choice. As a conclusion, solar cookers and solar cooking programs are not always adapted to the needs and requirements of the end-users. Needs-oriented and end-user adopted strategies are necessary in order to successfully implement nontraditional cookstoves programs. (C) 2013 Elsevier Ltd. All rights reserved. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000332815300043 |
Publication Date |
2014-01-08 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0301-4215; 1873-6777 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
4.14 |
Times cited |
10 |
Open Access |
|
|
| |
Notes |
; The authors thank the VLIR-UOS for their financial support and the Sol Suffit Program for their co-operation during the research. ; |
Approved |
Most recent IF: 4.14; 2014 IF: 2.575 |
|
| |
Call Number |
UA @ admin @ c:irua:127544 |
Serial |
6251 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Peeters, B.; Daems, D.; Van der Donck, T.; Delport, F.; Lammertyn, J. |
|
| |
Title |
Real-time FO-SPR monitoring of solid-phase DNAzyme cleavage activity for cutting-edge biosensing |
Type |
A1 Journal article |
| |
Year |
2019 |
Publication |
ACS applied materials and interfaces |
Abbreviated Journal |
|
|
| |
Volume |
11 |
Issue |
7 |
Pages |
6759-6768 |
|
| |
Keywords |
A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation) |
|
| |
Abstract |
DNA nanotechnology has a great potential in biosensor design including nanostructuring of the biosensor surface through DNA origami, target recognition by means of aptamers, and DNA-based signal amplification strategies. In this paper, we use DNA nanotechnology to describe for the first time the concept of real-time solid-phase monitoring of DNAzyme cleavage activity for the detection of specific single-stranded DNA (ssDNA) with a fiber optic surface plasmon resonance (FO-SPR) biosensor. Hereto, we first developed a robust ligation strategy for the functionalization of the FO-SPR biosensing surface with ssDNA-tethered gold nanoparticles, serving as the substrate for the DNAzyme. Next, we established a relation between the SPR signal change, due to the cleavage activity of the 10–23 DNAzyme, and the concentration of the DNAzyme, showing faster cleavage kinetics for higher DNAzyme concentrations. Finally, we implemented this generic concept for biosensing of ssDNA target in solution. Hereto, we designed a DNAzyme–inhibitor complex, consisting of an internal loop structure complementary to the ssDNA target, that releases active DNAzyme molecules in a controlled way as a function of the target concentration. We demonstrated reproducible target detection with a theoretical limit of detection of 1.4 nM, proving that the presented ligation strategy is key to a universal DNAzyme-based FO-SPR biosensing concept with promising applications in the medical and agrofood sector. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000459642200008 |
Publication Date |
2019-01-25 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1944-8244 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
no |
|
| |
Call Number |
UA @ admin @ c:irua:160132 |
Serial |
8457 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Dabaghmanesh, S.; Saniz, R.; Neyts, E.; Partoens, B. |
|
| |
Title |
Sulfur-alloyed Cr2O3: a new p-type transparent conducting oxide host |
Type |
A1 Journal article |
| |
Year |
2017 |
Publication |
RSC advances |
Abbreviated Journal |
Rsc Adv |
|
| |
Volume |
7 |
Issue |
7 |
Pages |
4453-4459 |
|
| |
Keywords |
A1 Journal article; Condensed Matter Theory (CMT); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
|
| |
Abstract |
Doped Cr2O3 has been shown to be a p-type transparent conducting oxide (TCO). Its conductivity, however, is low. As for most p-type TCOs, the main problem is the high effective hole mass due to flat valence bands. We use first-principles methods to investigate whether one can increase the valence band dispersion (i.e. reduce the hole mass) by anion alloying with sulfur, while keeping the band gap large enough for transparency. The alloying concentrations considered are given by Cr(4)SxO(6-x), with x = 1-5. To be able to describe the electronic properties of these materials accurately, we first study Cr2O3, examining critically the accuracy of different density functionals and methods, including PBE, PBE+U, HSE06, as well as perturbative approaches within the GW approximation. Our results demonstrate that Cr4S2O4 has an optical band gap of 3.08 eV and an effective hole mass of 1.8 m(e). This suggests Cr4S2O4 as a new p-type TCO host candidate. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000393751300030 |
Publication Date |
2017-01-16 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
2046-2069 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
3.108 |
Times cited |
9 |
Open Access |
OpenAccess |
|
| |
Notes |
; This work was supported by SIM vzw, Technologiepark 935, BE-9052 Zwijnaarde, Belgium, within the InterPoCo project of the H-INT-S horizontal program. The computational resources and services used in this work were provided by the Vlaams Supercomputer Centrum (VSC) and the HPC infrastructure of the University of Antwerp. ; |
Approved |
Most recent IF: 3.108 |
|
| |
Call Number |
UA @ lucian @ c:irua:141543 |
Serial |
4528 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Nematollahi, P.; Neyts, E.C. |
|
| |
Title |
Distribution pattern of metal atoms in bimetal-doped pyridinic-N₄ pores determines their potential for electrocatalytic N₂ reduction |
Type |
A1 Journal article |
| |
Year |
2022 |
Publication |
Journal Of Physical Chemistry A |
Abbreviated Journal |
J Phys Chem A |
|
| |
Volume |
126 |
Issue |
20 |
Pages |
3080-3089 |
|
| |
Keywords |
A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
|
| |
Abstract |
Doping two single transition-metal (TM) atoms on a substrate host opens numerous possibilities for catalyst design. However, what if the substrate contains more than one vacancy site? Then, the combination of two TMs along with their distribution patterns becomes a design parameter potentially complementary to the substrate itself and the bimetal composition. In this study, we investigate ammonia synthesis under mild electrocatalytic conditions on a transition-metal-doped porous C24N24 catalyst using density functional theory (DFT). The TMs studied include Ti, Mn, and Cu in a 2:4 dopant ratio (Ti2Mn4@C24N24 and Ti2Cu4@N-24(24)). Our computations show that a single Ti atom in both catalysts exhibits the highest selectivity for N-2 fixation at ambient conditions. This work is a good theoretical model to establish the structure-activity relationship, and the knowledge earned from the metal-N-4 moieties may help studies of related nanomaterials, especially those with curved structures. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000804119800003 |
Publication Date |
2022-05-12 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1089-5639; 1520-5215 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
2.9 |
Times cited |
|
Open Access |
OpenAccess |
|
| |
Notes |
|
Approved |
Most recent IF: 2.9 |
|
| |
Call Number |
UA @ admin @ c:irua:189023 |
Serial |
7146 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Sharafi, L.; Zarafshani, K.; Keshavarz, M.; Azadi, H.; Van Passel, S. |
|
| |
Title |
Farmers' decision to use drought early warning system in developing countries |
Type |
A1 Journal article |
| |
Year |
2021 |
Publication |
Science Of The Total Environment |
Abbreviated Journal |
Sci Total Environ |
|
| |
Volume |
758 |
Issue |
|
Pages |
142761 |
|
| |
Keywords |
A1 Journal article; Engineering Management (ENM) |
|
| |
Abstract |
Drought is a persistent, sluggish natural disaster in developing countries that has generated a financial burden and an unstable climate. Farmers should adopt early warning systems (EWS) in their strategies for monitoring drought to reduce its serious consequences. However, farmers in developing countries are reluctant to use EWS as their management strategies. Hence, the aim of this study was to investigate the decision of farmers to use climate knowledge through the model of farming activity in Kermanshah Township, Iran. A surveyor questionnaire was used to gather data from 370 wheat farmers using random sampling methods inmulti-stage clusters. Results revealed that the decision to use climate information is affected by personal factors, attitude towards climate information, objectives of using climate information, and external/physical farming factors. The result of this study has implications for drought management practitioners. To be specific, the results can aid policymakers to design early alert programs to minimize the risk of drought and thus move from conventional to climate smart agriculture. (C) 2020 Elsevier B.V. All rights reserved. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000605623800001 |
Publication Date |
2020-10-05 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0048-9697 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
4.9 |
Times cited |
|
Open Access |
OpenAccess |
|
| |
Notes |
|
Approved |
Most recent IF: 4.9 |
|
| |
Call Number |
UA @ admin @ c:irua:176030 |
Serial |
6924 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Zarafshani, K.; Sharafi, L.; Azadi, H.; Van Passel, S. |
|
| |
Title |
Vulnerability assessment models to drought : toward a conceptual framework |
Type |
A1 Journal article |
| |
Year |
2016 |
Publication |
Sustainability |
Abbreviated Journal |
Sustainability-Basel |
|
| |
Volume |
8 |
Issue |
6 |
Pages |
1-21 |
|
| |
Keywords |
A1 Journal article; Engineering Management (ENM) |
|
| |
Abstract |
Drought is regarded as a slow-onset natural disaster that causes inevitable damage to water resources and to farm life. Currently, crisis management is the basis of drought mitigation plans, however, thus far studies indicate that effective drought management strategies are based on risk management. As a primary tool in mitigating the impact of drought, vulnerability assessment can be used as a benchmark in drought mitigation plans and to enhance farmers ability to cope with drought. Moreover, literature pertaining to drought has focused extensively on its impact, only awarding limited attention to vulnerability assessment as a tool. Therefore, the main purpose of this paper is to develop a conceptual framework for designing a vulnerability model in order to assess farmers level of vulnerability before, during and after the onset of drought. Use of this developed drought vulnerability model would aid disaster relief workers by enhancing the adaptive capacity of farmers when facing the impacts of drought. The paper starts with the definition of vulnerability and outlines different frameworks on vulnerability developed thus far. It then identifies various approaches of vulnerability assessment and finally offers the most appropriate model. The paper concludes that the introduced model can guide drought mitigation programs in countries that are impacted the most by drought. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000378776800084 |
Publication Date |
2016-06-23 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
2071-1050 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
1.789 |
Times cited |
15 |
Open Access |
|
|
| |
Notes |
; ; |
Approved |
Most recent IF: 1.789 |
|
| |
Call Number |
UA @ admin @ c:irua:134331 |
Serial |
6278 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Ysebaert, T.; Samson, R.; Denys, S. |
|
| |
Title |
Revisiting dry deposition modelling of particulate matter on vegetation at the microscale |
Type |
A1 Journal article |
| |
Year |
2023 |
Publication |
Air quality, atmosphere & health |
Abbreviated Journal |
|
|
| |
Volume |
|
Issue |
|
Pages |
|
|
| |
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
Dry deposition is an important process determining pollutant concentrations, especially when studying the influence of urban green infrastructure on particulate matter (PM) levels in cities. Computational fluid dynamics (CFD) models of PM capture by vegetation are useful tools to increase their applicability. The meso-scale models of Zhang et al. (Atmos Environ 35:549-560, 2001) and Petroff and Zhang (Geosci Model Dev 3(2):753-769, 2010) have often been adopted in CFD models, however a comparison of these models with measurements including all PM particle sizes detrimental to health has been rarely reported and certainly not for green wall species. This study presents dry deposition experiments on real grown Hedera helix in a wind tunnel setup with wind speeds from 1 to 4 m s(-1) and PM consisting of a mixture of soot (0.02 – 0.2 mu mu m) and dust particles (0.3 – 10 mu mu m). Significant factors determining the collection efficiency (%) were particle diameter and wind speed, but relative air humidity and the type of PM (soot or dust) did not have a significant influence. Zhang's model outperformed Petroff's model for particles < 0.3 mu mu m, however the inclusion of turbulent impaction in Petroff's model resulted in better agreement with the measurements for particles > 2 – 3 mu mu m. The optimised model had an overall root-mean-square-error of similar to 4% for collection efficiency (CE) and 0.4 cm s-1 for deposition velocity (nu d), which was shown to be highly competitive against previously described models. It can thus be used to model PM deposition on other plant species, provided the correct parameterisation of the drag by this species. A detailed description of the spatial distribution of the vegetation could solve the underestimation for particle sizes of 0.3 – 2 mu mu m. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001125841300001 |
Publication Date |
2023-12-14 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1873-9318; 1873-9326 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
5.1 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 5.1; 2023 IF: 3.184 |
|
| |
Call Number |
UA @ admin @ c:irua:201986 |
Serial |
9086 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Rojas, C.M.; Van Grieken, R.E.; Laane, R.W. |
|
| |
Title |
Comparison of 3 dry deposition models applied to field-measurements in the Southern Bight of the North-Sea |
Type |
A1 Journal article |
| |
Year |
1993 |
Publication |
Atmospheric environment |
Abbreviated Journal |
|
|
| |
Volume |
27 |
Issue |
3 |
Pages |
363-370 |
|
| |
Keywords |
A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation) |
|
| |
Abstract |
Dry deposition velocities have been calculated using three different approaches. Turbulent wind profile theory has been used to predict the drag coefficient, wind speed and friction velocity at 10 m height when the wind speed is measured at a higher altitude. The resulting parameters were introduced in a two-layer deposition model. The second approach was the well-known model of Slinn and Slinn (1980, Atmospheric Environment 14, 1013-1016), whereas the third corresponded to the model published by Williams (1982, Atmospheric Environment 16, 1933 1938). Results point to clear differences. However, in a field experiment carried out at the Southern Bight of the North Sea, all three approaches show relatively comparable results. The role played by the size distribution of atmospheric particulate matter is essential. In our case any of the three models could have given satisfactory outcomes taking into account the wide spread of the experimental results cited in the literature for the same airshed. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
A1993KQ75200008 |
Publication Date |
2003-08-06 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0004-6981 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
no |
|
| |
Call Number |
UA @ admin @ c:irua:100018 |
Serial |
7690 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Herzog, M.J.; Gauquelin, N.; Esken, D.; Verbeeck, J.; Janek, J. |
|
| |
Title |
Increased Performance Improvement of Lithium-Ion Batteries by Dry Powder Coating of High-Nickel NMC with Nanostructured Fumed Ternary Lithium Metal Oxides |
Type |
A1 Journal article |
| |
Year |
2021 |
Publication |
ACS applied energy materials |
Abbreviated Journal |
ACS Appl. Energy Mater. |
|
| |
Volume |
4 |
Issue |
9 |
Pages |
8832-8848 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
Dry powder coating is an effective approach to protect the surfaces of layered cathode active materials (CAMs) in lithium-ion batteries. Previous investigations indicate an incorporation of lithium ions in fumed Al2O3, ZrO2, and TiO2 coatings on LiNi0.7Mn0.15Co0.15O2 during cycling, improving the cycling performance. Here, this coating approach is transferred for the first time to fumed ternary LiAlO2, Li4Zr3O8, and Li4Ti5O12 and directly compared with their lithium-free equivalents. All materials could be processed equally and their nanostructured small aggregates accumulate on the CAM surfaces to quite homogeneous coating layers with a certain porosity. The LiNixMnyCozO2 (NMC) coated with lithium-containing materials shows an enhanced improvement in overall capacity, capacity retention, rate performance, and polarization behavior during cycling, compared to their lithium-free analogues. The highest rate performance was achieved with the fumed ZrO2 coating, while the best long-term cycling stability with the highest absolute capacity was obtained for the fumed LiAlO2-coated NMC. The optimal coating agent for NMC to achieve a balanced system is fumed Li4Ti5O12, providing a good compromise between high rate capability and good capacity retention. The coating agents prevent CAM particle cracking and degradation in the order LiAlO2 ≈ Al2O3 > Li4Ti5O12 > Li4Zr3O8 > ZrO2 > TiO2. A schematic model for the protection and electrochemical performance enhancement of high-nickel NMC with fumed metal oxide coatings is sketched. It becomes apparent that physical and chemical characteristics of the coating significantly influence the performance of NMC. A high degree of coating-layer porosity is favorable for the rate capability, while a high coverage of the surface, especially in vulnerable grain boundaries, enhances the long-term cycling stability and improves the cracking behavior of NMCs. While zirconium-containing coatings possess the best chemical properties for high rate performances, aluminum-containing coatings feature a superior chemical nature to protect high-nickel NMCs. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000703338600018 |
Publication Date |
2021-09-27 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
2574-0962 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
|
Times cited |
15 |
Open Access |
OpenAccess |
|
| |
Notes |
For his support in scanning electron microscopy analysis, the authors thank Erik Peldszus. N. G. and J. V. acknowledge funding from GOA project “Solarpaint” of the University of Antwerp and from the Flemish Research Fund (FWO) project G0F1320N. The Qu-Ant-EM microscope and the direct electron detector were partly funded by the Hercules fund from the Flemish Government |
Approved |
Most recent IF: NA |
|
| |
Call Number |
EMAT @ emat @c:irua:183949 |
Serial |
6823 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Cleiren, E.; Heijkers, S.; Ramakers, M.; Bogaerts, A. |
|
| |
Title |
Dry Reforming of Methane in a Gliding Arc Plasmatron: Towards a Better Understanding of the Plasma Chemistry |
Type |
A1 Journal article |
| |
Year |
2017 |
Publication |
Chemsuschem |
Abbreviated Journal |
Chemsuschem |
|
| |
Volume |
10 |
Issue |
20 |
Pages |
4025-4036 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
|
| |
Abstract |
Dry reforming of methane (DRM) in a gliding arc plasmatron is studied for different CH4 fractions in the mixture. The CO2 and CH4 conversions reach their highest values of approximately 18 and 10%, respectively, at 25% CH4 in the gas mixture, corresponding to an overall energy cost of 10 kJ L@1 (or 2.5 eV per molecule) and an energy efficiency of 66%. CO and H2 are the major products, with the formation of smaller fractions of C2Hx (x=2, 4, or 6) compounds and H2O. A chemical kinetics model is used to investigate the underlying chemical processes. The calculated CO2 and CH4 conversion and the energy efficiency are in good agreement with the experimental data. The model calculations reveal that the reaction of CO2 (mainly at vibrationally excited levels) with H radicals is mainly responsible for
the CO2 conversion, especially at higher CH4 fractions in the mixture, which explains why the CO2 conversion increases with increasing CH4 fraction. The main process responsible for CH4 conversion is the reaction with OH radicals. The excellent energy efficiency can be explained by the non-equilibrium character of the plasma, in which the electrons mainly activate the gas molecules, and by the important role of the vibrational kinetics of CO2. The results demonstrate that a gliding arc plasmatron is very promising for DRM. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000413565100012 |
Publication Date |
2017-10-02 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1864-5631 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
7.226 |
Times cited |
23 |
Open Access |
OpenAccess |
|
| |
Notes |
Fonds Wetenschappelijk Onderzoek, G.0383.16N ; Federaal Wetenschapsbeleid; |
Approved |
Most recent IF: 7.226 |
|
| |
Call Number |
PLASMANT @ plasmant @c:irua:146665 |
Serial |
4759 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Snoeckx, R.; Zeng, Y.X.; Tu, X.; Bogaerts, A. |
|
| |
Title |
Plasma-based dry reforming : improving the conversion and energy efficiency in a dielectric barrier discharge |
Type |
A1 Journal article |
| |
Year |
2015 |
Publication |
RSC advances |
Abbreviated Journal |
Rsc Adv |
|
| |
Volume |
5 |
Issue |
5 |
Pages |
29799-29808 |
|
| |
Keywords |
A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
|
| |
Abstract |
Dry reforming of methane has gained significant interest over the years. A novel reforming technique with great potential is plasma technology. One of its drawbacks, however, is energy consumption. Therefore, we performed an extensive computational study, supported by experiments, aiming to identify the influence of the operating parameters (gas mixture, power, residence time and frequency) of a dielectric barrier discharge plasma on the conversion and energy efficiency, and to investigate which of these parameters lead to the most promising results and whether these are eventually sufficient for industrial implementation. The best results, in terms of both energy efficiency and conversion, are obtained at a specific energy input (SEI) of 100 J cm−3, a 1090 CH4CO2 ratio, 10 Hz, a residence time of 1 ms, resulting in a total conversion of 84% and an energy efficiency of 8.5%. In general, increasing the CO2 content in the gas mixture leads to a higher conversion and energy efficiency. The SEI couples the effect of the power and residence time, and increasing the SEI always results in a higher conversion, but somewhat lower energy efficiencies. The effect of the frequency is more complicated: we observed that the product of frequency (f) and residence time (τ), being a measure for the total number of micro-discharge filaments which the gas molecules experience when passing through the reactor, was critical. For most cases, a higher number of filaments yields higher values for conversion and energy efficiency. To benchmark our model predictions, we also give an overview of measured conversions and energy efficiencies reported in the literature, to indicate the potential for improvement compared to the state-of-the art. Finally, we identify the limitations as well as the benefits and future possibilities of plasma technology. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000352789500026 |
Publication Date |
2015-03-19 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
2046-2069; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
3.108 |
Times cited |
67 |
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 3.108; 2015 IF: 3.840 |
|
| |
Call Number |
c:irua:132577 |
Serial |
2629 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Wang, Y.-T.; Wu, S.-M.; Luo, G.-Q.; Tian, G.; Wang, L.-Y.; Xiao, S.-T.; Wu, J.-X.; Wu, A.; Wu, K.-J.; Lenaerts, S.; Yang, X.-Y. |
|
| |
Title |
A core-shell confined Pd@TS-1 @meso-SiO2 catalyst and its synergy effect on styrene oxidation |
Type |
A1 Journal article |
| |
Year |
2023 |
Publication |
Applied catalysis : A : general |
Abbreviated Journal |
|
|
| |
Volume |
650 |
Issue |
|
Pages |
119016-6 |
|
| |
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
Dual active sites from acidic zeolite and Pd are not only capable of catalyzing multiple type of reactions, but could also generate unique functions owing to the synergy between metals and acidic sites. However, there are only a few reports on the investigation of the synergy of acid/Pd dual sites in TS-1. Herein, TS-1 confined Pd catalyst with mesoporous silica shell (Pd@TS-1 @meso-SiO2) has been successfully synthesized and its synergy effect contributes to the enhanced conversion rate (19.2%) and selectivity (74.7%) on styrene oxidation. The interaction between Pd and TS-1 has been investigated by EPR and 1H NMR techniques, the experimental measurements show an obvious change in the signal distribution of weakly acidic terminal hydroxyls and hydrogen-bonding silanols. The schematic illustration of selective styrene oxidation in the model of Pd@TS-1 @meso-SiO2 is proposed to clarify the synergistic effect on styrene oxidation between TS-1 and Pd nanoparticles at an atomic-/nanoscale. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001015700000001 |
Publication Date |
2022-12-28 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0926-860x |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
5.5 |
Times cited |
|
Open Access |
Not_Open_Access |
|
| |
Notes |
|
Approved |
Most recent IF: 5.5; 2023 IF: 4.339 |
|
| |
Call Number |
UA @ admin @ c:irua:197805 |
Serial |
8826 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Abdullah, H.M.; Van der Donck, M.; Bahlouli, H.; Peeters, F.M.; Van Duppen, B. |
|
| |
Title |
Graphene quantum blisters : a tunable system to confine charge carriers |
Type |
A1 Journal article |
| |
Year |
2018 |
Publication |
Applied physics letters |
Abbreviated Journal |
Appl Phys Lett |
|
| |
Volume |
112 |
Issue |
21 |
Pages |
213101 |
|
| |
Keywords |
A1 Journal article; Condensed Matter Theory (CMT) |
|
| |
Abstract |
Due to Klein tunneling, electrostatic confinement of electrons in graphene is not possible. This hinders the use of graphene for quantum dot applications. Only through quasi-bound states with finite lifetime has one achieved to confine charge carriers. Here, we propose that bilayer graphene with a local region of decoupled graphene layers is able to generate bound states under the application of an electrostatic gate. The discrete energy levels in such a quantum blister correspond to localized electron and hole states in the top and bottom layers. We find that this layer localization and the energy spectrum itself are tunable by a global electrostatic gate and that the latter also coincides with the electronic modes in a graphene disk. Curiously, states with energy close to the continuum exist primarily in the classically forbidden region outside the domain defining the blister. The results are robust against variations in size and shape of the blister which shows that it is a versatile system to achieve tunable electrostatic confinement in graphene. Published by AIP Publishing. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
American Institute of Physics |
Place of Publication |
New York, N.Y. |
Editor |
|
|
| |
Language |
|
Wos |
000433140900025 |
Publication Date |
2018-05-22 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0003-6951; 1077-3118 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
3.411 |
Times cited |
9 |
Open Access |
|
|
| |
Notes |
; H.M.A. and H.B. acknowledge the Saudi Center for Theoretical Physics (SCTP) for their generous support and the support of KFUPM under physics research group Project Nos. RG1502-1 and RG1502-2. This work was supported by the Flemish Science Foundation (FWO-Vl) by a post-doctoral fellowship (B.V.D.) and a doctoral fellowship (M.V.d.D.). ; |
Approved |
Most recent IF: 3.411 |
|
| |
Call Number |
UA @ lucian @ c:irua:151505UA @ admin @ c:irua:151505 |
Serial |
5027 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Xie, Y.; Spiller, M.; Vlaeminck, S.E. |
|
| |
Title |
A bioreactor and nutrient balancing approach for the conversion of solid organic fertilizers to liquid nitrate-rich fertilizers : mineralization and nitrification performance complemented with economic aspects |
Type |
A1 Journal article |
| |
Year |
2022 |
Publication |
The science of the total environment |
Abbreviated Journal |
Sci Total Environ |
|
| |
Volume |
806 |
Issue |
|
Pages |
150415 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
Due to the high water- and nutrient-use efficiency, hydroponic cultivation is increasingly vital in progressing to environment-friendly food production. To further alleviate the environmental impacts of synthetic fertilizer production, the use of recovered nutrients should be encouraged in horticulture and agriculture at large. Solid organic fertilizers can largely contribute to this, yet their physical and chemical nature impedes application in hydroponics. This study proposes a bioreactor for mineralization and nitrification followed by a supplementation step for limiting macronutrients to produce nitrate-based solutions from solid fertilizers, here based on a novel microbial fertilizer. Batch tests showed that aerobic conversions at 35 °C could realize a nitrate (NO₃−-N) production efficiency above 90% and a maximum rate of 59 mg N L−1 d−1. In the subsequent bioreactor test, nitrate production efficiencies were lower (44–51%), yet rates were higher (175–212 mg N L−1 d−1). Calcium and magnesium hydroxide were compared to control the bioreactor pH at 6.0 ± 0.2, while also providing macronutrients for plant production. A mass balance estimation to mimic the Hoagland nutrient solution showed that 92.7% of the NO₃−-N in the Ca(OH)₂ scenario could be organically sourced, while this was only 37.4% in the Mg(OH)₂ scenario. Besides, carbon dioxide (CO₂) generated in the bioreactor can be used for greenhouse carbon fertilization to save operational expenditure (OPEX). An estimation of the total OPEX showed that the production of a nutrient solution from solid organic fertilizers can be cost competitive compared to using commercially available liquid inorganic fertilizer solutions. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000707640400021 |
Publication Date |
2021-09-20 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0048-9697 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
9.8 |
Times cited |
|
Open Access |
OpenAccess |
|
| |
Notes |
|
Approved |
Most recent IF: 9.8 |
|
| |
Call Number |
UA @ admin @ c:irua:181787 |
Serial |
7132 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Ao, Z.M.; Peeters, F.M. |
|
| |
Title |
Electric field: A catalyst for hydrogenation of graphene |
Type |
A1 Journal article |
| |
Year |
2010 |
Publication |
Applied physics letters |
Abbreviated Journal |
Appl Phys Lett |
|
| |
Volume |
96 |
Issue |
25 |
Pages |
3 |
|
| |
Keywords |
A1 Journal article; Condensed Matter Theory (CMT) |
|
| |
Abstract |
Due to the importance of hydrogenation of graphene for several applications, we present an alternative approach to hydrogenate graphene based on density functional theory calculations. We find that a negative perpendicular electric field F can act as a catalyst to reduce the energy barrier for molecular H<sub>2</sub> dissociative adsorption on graphene. Increasing -F above 0.02 a.u. (1 a.u.=5.14×10<sup>11</sup> V/m), this hydrogenation process occurs smoothly without any potential barrier. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
American Institute of Physics |
Place of Publication |
New York, N.Y. |
Editor |
|
|
| |
Language |
|
Wos |
000279168100052 |
Publication Date |
2010-06-23 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0003-6951; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
3.411 |
Times cited |
88 |
Open Access |
|
|
| |
Notes |
; This work was supported by the Flemish Science Foundation (FWO-Vl) and the Belgian Science Policy (IAP). ; |
Approved |
Most recent IF: 3.411; 2010 IF: 3.841 |
|
| |
Call Number |
UA @ lucian @ c:irua:83924 |
Serial |
881 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Joolaie, R.; Sarvestani, A.A.; Taheri, F.; Van Passel, S.; Azadi, H. |
|
| |
Title |
Sustainable cropping pattern in North Iran : application of fuzzy goal programming |
Type |
A1 Journal article |
| |
Year |
2017 |
Publication |
Environment, development and sustainability |
Abbreviated Journal |
|
|
| |
Volume |
19 |
Issue |
6 |
Pages |
2199-2216 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM) |
|
| |
Abstract |
Due to the important role that the application of mathematical programming models have in determining optimal cropping patterns, this research presents a sustainable cropping pattern that considers selected economic, environmental, and social goals together. Using a random sampling method, a sample size of 168 farmers was selected in the Sari County, Iran. Our results showed that economic, self-sufficiency, environmental, and social goals have a distinctly different impact on cropping pattern performance. Compared to the current cropping pattern, the gross margins for economic and social goals increased by nearly 11 and 2 %, respectively, and the gross margins for self-sufficiency and environmental goals decreased by nearly 2 and 36 %. Interestingly, it has been found that the performance of the current cropping pattern has an average positive impact of 6 % if economic, self-sufficiency, environmental, and social (employment) goals are realized simultaneously. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000414459300004 |
Publication Date |
2016-09-02 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1387-585x |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles; WoS full record; WoS citing articles |
|
| |
Impact Factor |
|
Times cited |
2 |
Open Access |
|
|
| |
Notes |
; ; |
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ admin @ c:irua:147370 |
Serial |
6257 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Liu, M.; Yi, Y.; Wang, L.; Guo, H.; Bogaerts, A |
|
| |
Title |
Hydrogenation of Carbon Dioxide to Value-Added Chemicals by Heterogeneous Catalysis and Plasma Catalysis |
Type |
A1 Journal article |
| |
Year |
2019 |
Publication |
Catalysts |
Abbreviated Journal |
Catalysts |
|
| |
Volume |
9 |
Issue |
3 |
Pages |
275 |
|
| |
Keywords |
A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
|
| |
Abstract |
Due to the increasing emission of carbon dioxide (CO2), greenhouse effects are becoming more and more severe, causing global climate change. The conversion and utilization of CO2 is one of the possible solutions to reduce CO2 concentrations. This can be accomplished, among other methods, by direct hydrogenation of CO2, producing value-added products. In this review, the progress of mainly the last five years in direct hydrogenation of CO2 to value-added chemicals (e.g., CO, CH4, CH3OH, DME, olefins, and higher hydrocarbons) by heterogeneous catalysis and plasma catalysis is summarized, and research priorities for CO2 hydrogenation are proposed. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000465012800055 |
Publication Date |
2019-03-18 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
2073-4344 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
3.082 |
Times cited |
|
Open Access |
OpenAccess |
|
| |
Notes |
Fundamental Research Funds for the Central Universities of China , DUT18JC42 32249 ; National Natural Science Foundation of China , 21503032 ; PetroChina Innovation Foundation , 2018D-5007-0501 ; |
Approved |
Most recent IF: 3.082 |
|
| |
Call Number |
PLASMANT @ plasmant @UA @ admin @ c:irua:158094 |
Serial |
5162 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Wang, Q.; Lin, S.; Liu, X.; Xu, W.; Xiao, Y.; Liang, C.; Ding, L.; Peeters, F.M. |
|
| |
Title |
Photoluminescence and electronic transition behaviors of single-stranded DNA |
Type |
A1 Journal article |
| |
Year |
2021 |
Publication |
Physical Review E |
Abbreviated Journal |
Phys Rev E |
|
| |
Volume |
104 |
Issue |
3 |
Pages |
034412 |
|
| |
Keywords |
A1 Journal article; Condensed Matter Theory (CMT) |
|
| |
Abstract |
Due to the potential application of DNA for biophysics and optoelectronics, the electronic energy states and transitions of this genetic material have attracted a great deal of attention recently. However, the fluorescence and corresponding physical process of DNA under optical excitation with photon energies below ultraviolet are still not fully clear. In this work, we experimentally investigate the photoluminescence (PL) properties of single-stranded DNA (ssDNA) samples under near-ultraviolet (NUV) and visible excitations (270 similar to 440 nm). Based on the dependence of the PL peak wavelength (lem) upon the excitation wavelength (lex), the PL behaviors of ssDNA can be approximately classified into two categories. In the relatively short excitation wavelength regime, lem is nearly constant due to exciton-like transitions associated with delocalized excitonic states and excimer states. In the relatively long excitation wavelength range, a linear relation of lem = Alex + B with A 0 or A < 0 can be observed, which comes from electronic transitions related to coupled vibrational-electronic levels. Moreover, the transition channels in different excitation wavelength regimes and the effects of strand length and base type can be analyzed on the basis of these results. These important findings not only can give a general description of the electronic energy states and transitional behaviors of ssDNA samples under NUV and visible excitations, but also can be the basis for the application of DNA in nanoelectronics and optoelectronics. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000703562300002 |
Publication Date |
2021-09-20 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
2470-0053 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
2.366 |
Times cited |
|
Open Access |
OpenAccess |
|
| |
Notes |
|
Approved |
Most recent IF: 2.366 |
|
| |
Call Number |
UA @ admin @ c:irua:182517 |
Serial |
7009 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Khalil-Allafi, J.; Amin-Ahmadi, B.; Zare, M. |
|
| |
Title |
Biocompatibility and corrosion behavior of the shape memory NiTi alloy in the physiological environments simulated with body fluids for medical applications |
Type |
A1 Journal article |
| |
Year |
2010 |
Publication |
Materials science and engineering: part C: biomimetic materials |
Abbreviated Journal |
Mat Sci Eng C-Mater |
|
| |
Volume |
30 |
Issue |
8 |
Pages |
1112-1117 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
Due to unique properties of NiTi shape memory alloys such as high corrosion resistance, biocompatibility, super elasticity and shape memory behavior, NiTi shape memory alloys are suitable materials for medical applications. Although TiO2 passive layer in these alloys can prevent releasing of nickel to the environment, high nickel content and stability of passive layer in these alloys are very debatable subjects. In this study a NiTi shape memory alloy with nominal composition of 50.7 atom% Ni was investigated by corrosion tests. Electrochemical tests were performed in two physiological environments of Ringer solution and NaCl 0.9% solution. Results indicate that the breakdown potential of the NiTi alloy in NaCl 0.9% solution is higher than that in Ringer solution. The results of Scanning Electron Microscope (SEM) reveal that low pitting corrosion occurred in Ringer solution compared with NaCl solution at potentiostatic tests. The pH value of the solutions increases after the electrochemical tests. The existence of hydride products in the X-ray diffraction analysis confirms the decrease of the concentration of hydrogen ion in solutions. Topographical evaluations show that corrosion products are nearly same in all samples. The biocompatibility tests were performed by reaction of mouse fibroblast cells (L929). The growth and development of cells for different times were measured by numbering the cells or statistics investigations. The figures of cells for different times showed natural growth of cells. The different of the cell numbers between the test specimen and control specimen was negligible; therefore it may be concluded that the NiTi shape memory alloy is not toxic in the physiological environments simulated with body fluids. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
|
| |
Language |
|
Wos |
000282905600006 |
Publication Date |
2010-06-23 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0928-4931; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
4.164 |
Times cited |
34 |
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 4.164; 2010 IF: 2.180 |
|
| |
Call Number |
UA @ lucian @ c:irua:122039 |
Serial |
242 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Chen, X.; Li, L.; Peeters, F.M.; Sanyal, B. |
|
| |
Title |
Two-dimensional oxygen functionalized honeycomb and zigzag dumbbell silicene with robust Dirac cones |
Type |
A1 Journal article |
| |
Year |
2021 |
Publication |
New Journal Of Physics |
Abbreviated Journal |
New J Phys |
|
| |
Volume |
23 |
Issue |
2 |
Pages |
023007 |
|
| |
Keywords |
A1 Journal article; Condensed Matter Theory (CMT) |
|
| |
Abstract |
Dumbbell-like structures are recently found to be energetically favored in group IV two-dimensional (2D) materials, exhibiting rich physics and many interesting properties. In this paper, using first-principles calculations, we have investigated the oxidized form of the hexagonal honeycomb (ODB-h) and zigzag dumbbell silicene (ODB-z). We confirm that both oxidization processes are energetically favorable, and their phonon spectra further demonstrate the dynamic stability. Contrary to the pristine dumbbell silicene structures (PDB-h and PDB-z silicene), these oxidized products ODB-h and ODB-z silicene are both semimetals with Dirac cones at the Fermi level. The Dirac cones of ODB-h and ODB-z silicene are at the K point and between Y and Gamma points respectively, possessing high Fermi velocities of 3.1 x 10(5) m s(-1) (ODB-h) and 2.9-3.4 x 10(5) m s(-1) (ODB-z). The origin of the Dirac cones is further explained by tight-binding models. The semimetallic properties of ODB-h and ODB-z are sensitive to compression due to the self-absorption effect, but quite robust against the tensile strain. These outstanding properties make oxidized dumbbell silicene a promising material for quantum computing and high-speed electronic devices. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000616114900001 |
Publication Date |
2021-01-14 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1367-2630 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
3.786 |
Times cited |
2 |
Open Access |
OpenAccess |
|
| |
Notes |
|
Approved |
Most recent IF: 3.786 |
|
| |
Call Number |
UA @ admin @ c:irua:176575 |
Serial |
6741 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Dillen, A.; Vandezande, W.; Daems, D.; Lammertyn, J. |
|
| |
Title |
Unraveling the effect of the aptamer complementary element on the performance of duplexed aptamers : a thermodynamic study |
Type |
A1 Journal article |
| |
Year |
2021 |
Publication |
Analytical And Bioanalytical Chemistry |
Abbreviated Journal |
Anal Bioanal Chem |
|
| |
Volume |
413 |
Issue |
19 |
Pages |
4739-4750 |
|
| |
Keywords |
A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation) |
|
| |
Abstract |
Duplexed aptamers (DAs) are widespread aptasensor formats that simultaneously recognize and signal the concentration of target molecules. They are composed of an aptamer and aptamer complementary element (ACE) which consists of a short oligonucleotide that partially inhibits the aptamer sequence. Although the design principles to engineer DAs are straightforward, the tailored development of DAs for a particular target is currently based on trial and error due to limited knowledge of how the ACE sequence affects the final performance of DA biosensors. Therefore, we have established a thermodynamic model describing the influence of the ACE on the performance of DAs applied in equilibrium assays and demonstrated that this relationship can be described by the binding strength between the aptamer and ACE. To validate our theoretical findings, the model was applied to the 29-mer anti-thrombin aptamer as a case study, and an experimental relation between the aptamer-ACE binding strength and performance of DAs was established. The obtained results indicated that our proposed model could accurately describe the effect of the ACE sequence on the performance of the established DAs for thrombin detection, applied for equilibrium assays. Furthermore, to characterize the binding strength between the aptamer and ACEs evaluated in this work, a set of fitting equations was derived which enables thermodynamic characterization of DNA-based interactions through thermal denaturation experiments, thereby overcoming the limitations of current predictive software and chemical denaturation experiments. Altogether, this work encourages the development, characterization, and use of DAs in the field of biosensing. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000659366300001 |
Publication Date |
2021-06-10 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1618-2642; 1618-2650 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
3.431 |
Times cited |
|
Open Access |
Not_Open_Access |
|
| |
Notes |
|
Approved |
Most recent IF: 3.431 |
|
| |
Call Number |
UA @ admin @ c:irua:179163 |
Serial |
8713 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Christiaens, M.E.R.; De Paepe, J.; Ilgrande, C.; De Vrieze, J.; Barys, J.; Teirlinck, P.; Meerbergen, K.; Lievens, B.; Boon, N.; Clauwaert, P.; Vlaeminck, S.E. |
|
| |
Title |
Urine nitrification with a synthetic microbial community |
Type |
A1 Journal article |
| |
Year |
2019 |
Publication |
Systematic and applied microbiology |
Abbreviated Journal |
|
|
| |
Volume |
42 |
Issue |
6 |
Pages |
Unsp 126021 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
During long-term extra-terrestrial missions, food is limited and waste is generated. By recycling valuable nutrients from this waste via regenerative life support systems, food can be produced in space. Astronauts' urine can, for instance, be nitrified by micro-organisms into a liquid nitrate fertilizer for plant growth in space. Due to stringent conditions in space, microbial communities need to be be defined (gnotobiotic); therefore, synthetic rather than mixed microbial communities are preferred. For urine nitrification, synthetic communities face challenges, such as from salinity, ureolysis, and organics. In this study, a synthetic microbial community containing an AOB (Nitrosomonas europaea), NOB (Nitrobacter winogradskyi), and three ureolytic heterotrophs (Pseudomonas fluorescens, Acidovorax delafieldii, and Delftia acidovorans) was compiled and evaluated for these challenges. In reactor 1, salt adaptation of the ammonium-fed AOB and NOB co-culture was possible up to 45 mS cm(-1), which resembled undiluted nitrified urine, while maintaining a 44 +/- 10 mg NH4+-N L-1 d(-1) removal rate. In reactor 2, the nitrifiers and ureolytic heterotrophs were fed with urine and achieved a 15 +/- 6 mg NO3--N L-1 d(-1) production rate for 1% and 10% synthetic and fresh real urine, respectively. Batch activity tests with this community using fresh real urine even reached 29 +/- 3 mg N L-1 d(-1). Organics removal in the reactor (69 +/- 15%) should be optimized to generate a nitrate fertilizer for future space applications. (C) 2019 Elsevier GmbH. All rights reserved. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000494650600006 |
Publication Date |
2019-09-23 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0723-2020; 1618-0984 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
no |
|
| |
Call Number |
UA @ admin @ c:irua:164650 |
Serial |
8717 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Broos, W.; Wittner, N.; Geerts, J.; Dries, J.; Vlaeminck, S.E.; Gunde-Cimerman, N.; Richel, A.; Cornet, I. |
|
| |
Title |
Evaluation of lignocellulosic wastewater valorization with the oleaginous yeasts R. kratochvilovae EXF7516 and C. oleaginosum ATCC 20509 |
Type |
A1 Journal article |
| |
Year |
2022 |
Publication |
Fermentation |
Abbreviated Journal |
|
|
| |
Volume |
8 |
Issue |
5 |
Pages |
204-221 |
|
| |
Keywords |
A1 Journal article; Pharmacology. Therapy; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL); Biochemical Wastewater Valorization & Engineering (BioWaVE) |
|
| |
Abstract |
During the conversion of lignocellulose, phenolic wastewaters are generated. Therefore, researchers have investigated wastewater valorization processes in which these pollutants are converted to chemicals, i.e., lipids. However, wastewaters are lean feedstocks, so these valorization processes in research typically require the addition of large quantities of sugars and sterilization, which increase costs. This paper investigates a repeated batch fermentation strategy with Rhodotorula kratochvilovae EXF7516 and Cutaneotrichosporon oleaginosum ATCC 20509, without these requirements. The pollutant removal and its conversion to microbial oil were evaluated. Because of the presence of non-monomeric substrates, the ligninolytic enzyme activity was also investigated. The repeated batch fermentation strategy was successful, as more lipids accumulated every cycle, up to a total of 5.4 g/L (23% cell dry weight). In addition, the yeasts consumed up to 87% of monomeric substrates, i.e., sugars, aromatics, and organics acids, and up to 23% of non-monomeric substrates, i.e., partially degraded xylan, lignin, cellulose. Interestingly, lipid production was only observed during the harvest phase of each cycle, as the cells experienced stress, possibly due to oxygen limitation. This work presents the first results on the feasibility of valorizing non-sterilized lignocellulosic wastewater with R. kratochvilovae and C. oleaginosum using a cost-effective repeated batch strategy. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000801796000001 |
Publication Date |
2022-05-01 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
2311-5637 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
OpenAccess |
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ admin @ c:irua:187883 |
Serial |
7157 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Mescia, L.; Chiapperino, M.A.; Bia, P.; Gielis, J.; Caratelli, D. |
|
| |
Title |
Modeling of electroporation induced by pulsed electric fields in irregularly shaped cells |
Type |
A1 Journal article |
| |
Year |
2018 |
Publication |
IEEE transactions on biomedical engineering |
Abbreviated Journal |
|
|
| |
Volume |
65 |
Issue |
2 |
Pages |
414-423 |
|
| |
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
During the past decades, the poration of cell membrane induced by pulsed electric fields has been widely investigated. Since the basic mechanisms of this process have not yet been fully clarified, many research activities are focused on the development of suitable theoretical and numerical models. To this end, a nonlinear, nonlocal, dispersive, and space-time numerical algorithm has been developed and adopted to evaluate the transmembrane voltage and pore density along the perimeter of realistic irregularly shaped cells. The presented model is based on the Maxwell's equations and the asymptotic Smoluchowski's equation describing the pore dynamics. The dielectric dispersion of the media forming the cell has been modeled by using a general multirelaxation Debye-based formulation. The irregular shape of the cell is described by using the Gielis' superformula. Different test cases pertaining to red blood cells, muscular cells, cell in mitosis phase, and cancer-like cell have been investigated. For each type of cell, the influence of the relevant shape, the dielectric properties, and the external electric pulse characteristics on the electroporation process has been analyzed. The numerical results demonstrate that the proposed model is an efficient numerical tool to study the electroporation problem in arbitrary-shaped cells. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000422914700018 |
Publication Date |
2017-11-13 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0018-9294 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
no |
|
| |
Call Number |
UA @ admin @ c:irua:148417 |
Serial |
8264 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Mihucz, V.G.; Varga, Z.; Tatár, E.; Virág, I.; Van Grieken, R.; Koleszár, Z.; Záray, G. |
|
| |
Title |
Redistribution of uranium and thorium by soil/plant interaction in a recultivated mining area |
Type |
A1 Journal article |
| |
Year |
2008 |
Publication |
Microchemical journal |
Abbreviated Journal |
|
|
| |
Volume |
90 |
Issue |
1 |
Pages |
44-49 |
|
| |
Keywords |
A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation) |
|
| |
Abstract |
During the recultivation of the uranium mining area of Kõvágószõlõs (Hungary), the tailings were covered with clay and loess soil layers having a thickness of 30 cm and 100 cm, respectively. In the loess covering layer, acacia (Robinia pseudoacacia), poplars (Populus × albus, Populus × canescens), oak (Quercus pubescens), silver tree (Eleagnus angustifolia) were planted between 1996 and 2004. In order to establish the extent of the uranium and thorium transport from the sludge to the leaves by uptake and translocation processes through roots with a length higher than 1.3 m results in a remarkable redistribution of these pollutants, a gray poplar tree, growing spontaneously in the last uncovered tailing, being selected as reference tree. The U and Th concentrations in the leaves of the above-mentioned trees, in the covering layers as well as in the original sludge were determined by inductively coupled plasma sector field mass spectrometry (ICP-SF-MS). Generally, the Th concentration of the soils was about 4 times higher than that of uranium, while uranium concentration was about 10130 times higher than that of thorium in the leaf samples and its concentration ranged from 28 to 1045 ng g− 1, the last value belonging to the poplar tree growing on the last uncovered tailing. In order to assume the mobility and bioavailability of uranium if the dry leaves fall down, the uranium species in the leaves of the poplar tree growing in the uncovered reservoir were determined applying ultrasound-assisted extraction with distilled water and ammonium acetate as well as high performance liquid chromatographic (HPLC)-ICP-SF-MS technique. About 20% of total uranium could be extracted in form of uranyl cations and a presumably negatively charged uranium compound. Estimations revealed that the annual increment of U in the soil surface layer due to the dead fallen leaves in case of the investigated gray poplar (Populus × canescens) is about 1.2%. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000258744000008 |
Publication Date |
2008-03-21 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0026-265x; 0026-265x |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
no |
|
| |
Call Number |
UA @ admin @ c:irua:70717 |
Serial |
8464 |
|
| Permanent link to this record |
