| Home | << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 >> |
|
| Records | |||||
|---|---|---|---|---|---|
| Author | Molina-Luna, L.; Duerrschnabel, M.; Turner, S.; Erbe, M.; Martinez, G.T.; Van Aert, S.; Holzapfel, B.; Van Tendeloo, G. | ||||
| Title | Atomic and electronic structures of BaHfO3-doped TFA-MOD-derived YBa2Cu3O7−δthin films | Type | A1 Journal article | ||
Year  |
2015 | Publication | Superconductor science and technology | Abbreviated Journal | Supercond Sci Tech |
| Volume | 28 | Issue | 28 | Pages | 115009 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Tailoring the properties of oxide-based nanocomposites is of great importance for a wide range of materials relevant for energy technology. YBa2Cu3O7−δ (YBCO) superconducting thin films containing nanosized BaHfO3 (BHO) particles yield a significant improvement of the magnetic flux pinning properties and a reduced anisotropy of the critical current density. These films were prepared by chemical solution deposition (CSD) on (100) SrTiO3 (STO) substrates yielding critical current densities up to 3.6 MA cm−2 at 77 K and self-field. Transport in-field J c measurements demonstrated a high pinning force maximum of around 6 GN/m3 for a sample annealed at T = 760 °C that has a doping of 12 mol% of BHO. This sample was investigated by scanning transmission electron microscopy (STEM) in combination with electron energy-loss spectroscopy (EELS) yielding strain and spectral maps. Spherical BHO nanoparticles of 15 nm in size were found in the matrix, whereas the particles at the interface were flat. A 2 nm diffusion layer containing Ti was found at the YBCO (BHO)/STO interface. Local lattice deformation mapping at the atomic scale revealed crystal defects induced by the presence of both sorts of BHO nanoparticles, which can act as pinning centers for magnetic flux lines. Two types of local lattice defects were identified and imaged: (i) misfit edge dislocations and (ii) Ba-Cu-Cu-Ba stacking faults (Y-248 intergrowths). The local electronic structure and charge transfer were probed by high energy resolution monochromated electron energy-loss spectroscopy. This technique made it possible to distinguish superconducting from non-superconducting areas in nanocomposite samples with atomic resolution in real space, allowing the identification of local pinning sites on the order of the coherence length of YBCO (~1.5 nm) and the determination of 0.25 nm dislocation cores. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000366193000018 | Publication Date | 2015-09-25 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0953-2048;1361-6668; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 2.878 | Times cited | 4 | Open Access | |
| Notes | The authors thank financial support from the European Union under the Framework 6 program as a contract for an Integrated Infrastructure Initiative (References No. 026019 ESTEEM) and by the EUFP6 Research Project “NanoEngineered Superconductors for Power Applications” NESPA no. MRTN-CT-2006-035619. This work was supported by funding from the European Research Council under the Seventh Framework Programme (FP7). L.M.L, S.T. and G.V.T acknowledge ERC grant N°246791 – COUNTATOMS and funding under a contract for an Integrated Infrastructure Initiative, Reference No. 312483- ESTEEM2, as well as the EC project EUROTAPES. G.T.M. and S.V.A acknowledge financial support from the Fund for Scientific Research-Flanders (Reference G.0064.10N and G.0393.11N). M.D. acknowledges financial support from the LOEWE research cluster RESPONSE (Hessen, Germany). M.E. has received funding from the European Union Seventh Framework Programme (FP7/2007–2013) under grant agreement n° NMP-LA-2012-280432.; esteem2jra2; esteem2jra3 | Approved | Most recent IF: 2.878; 2015 IF: 2.325 | ||
| Call Number | c:irua:129199 c:irua:129199 | Serial | 3942 | ||
| Permanent link to this record | |||||
| Author | Erbe, M.; Hänisch, J.; Hühne, R.; Freudenberg, T.; Kirchner, A.; Molina-Luna, L.; Damm, C.; Van Tendeloo, G.; Kaskel, S.; Schultz, L.; Holzapfel, B. | ||||
| Title | BaHfO3artificial pinning centres in TFA-MOD-derived YBCO and GdBCO thin films | Type | A1 Journal article | ||
| Year |
2015 | Publication | Superconductor science and technology | Abbreviated Journal | Supercond Sci Tech |
| Volume | 28 | Issue | 28 | Pages | 114002 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Chemical solution deposition (CSD) is a promising way to realize REBa2Cu3O7−x (REBCO;RE = rare earth (here Y, Gd))-coated conductors with high performance in applied magnetic fields. However, the preparation process contains numerous parameters which need to be tuned to achieve high-quality films. Therefore, we investigated the growth of REBCO thin films containing nanometre-scale BaHfO3 (BHO) particles as pinning centres for magnetic flux lines, with emphasis on the influence of crystallization temperature and substrate on the microstructure and superconductivity. Conductivity, microscopy and x-ray investigations show an enhanced performance of BHO nano-composites in comparison to pristine REBCO. Further, those measurements reveal the superiority of GdBCO to YBCO—e.g. by inductive critical current densities, Jc, at self-field and 77 K. YBCO is outperformed by more than 1 MA cm−2 with Jc values of up to 5.0 MA cm−2 for 265 nm thick layers of GdBCO(BHO) on lanthanum aluminate. Transport in-field Jc measurements demonstrate high pinning force maxima of around 4 GN m−3 for YBCO(BHO) and GdBCO(BHO). However, the irreversibility fields are appreciably higher for GdBCO. The critical temperature was not significantly reduced upon BHO addition to both YBCO and GdBCO, indicating a low tendency for Hf diffusion into the REBCO matrix. Angular-dependent Jc measurements show a reduction of the anisotropy in the same order of magnitude for both REBCO compounds. Theoretical models suggest that more than one sort of pinning centre is active in all CSD films. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000366193000003 | Publication Date | 2015-09-25 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0953-2048;1361-6668; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 2.878 | Times cited | 36 | Open Access | |
| Notes | Experimental work was mainly done at IFW Dresden. We thank Juliane Scheiter and Dr Jens Ingolf Mönch of IFW Dresden for technical assistance. The research leading to these results received funding from EUROTAPES, a collaborative project funded by the European Union Seventh Framework Programme (FP7/2007–2013) under grant agreement no. NMP-LA-2012-280 432. L Molina-Luna and G Van Tendeloo acknowledge funding from the European Research Council (ERC grant nr. 24 691-COUNTATOMS). | Approved | Most recent IF: 2.878; 2015 IF: 2.325 | ||
| Call Number | c:irua:129200 | Serial | 3941 | ||
| Permanent link to this record | |||||
| Author | McCalla, E.; Abakumov, A.M.; Saubanere, M.; Foix, D.; Berg, E.J.; Rousse, G.; Doublet, M.-L.; Gonbeau, D.; Novak, P.; Van Tendeloo, G.; Dominko, R.; Tarascon, J.-M. | ||||
| Title | Visualization of O-O peroxo-like dimers in high-capacity layered oxides for Li-ion batteries | Type | A1 Journal article | ||
| Year |
2015 | Publication | Science | Abbreviated Journal | Science |
| Volume | 350 | Issue | 350 | Pages | 1516-1521 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Lithium-ion (Li-ion) batteries that rely on cationic redox reactions are the primary energy source for portable electronics. One pathway toward greater energy density is through the use of Li-rich layered oxides. The capacity of this class of materials (>270 milliampere hours per gram) has been shown to be nested in anionic redox reactions, which are thought to form peroxo-like species. However, the oxygen-oxygen (O-O) bonding pattern has not been observed in previous studies, nor has there been a satisfactory explanation for the irreversible changes that occur during first delithiation. By using Li2IrO3 as a model compound, we visualize the O-O dimers via transmission electron microscopy and neutron diffraction. Our findings establish the fundamental relation between the anionic redox process and the evolution of the O-O bonding in layered oxides. | ||||
| Address | College de France, Chimie du Solide et de l'Energie, FRE 3677, 11 Place Marcelin Berthelot, 75231 Paris Cedex 05, France. ALISTORE-European Research Institute, FR CNRS 3104, 80039 Amiens, France. Reseau sur le Stockage Electrochimique de l'Energie (RS2E), FR CNRS 3459, France. Sorbonne Universites-UPMC Univ Paris 06, 4 Place Jussieu, F-75005 Paris, France. jean-marie.tarascon@college-de-france.fr | ||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | English | Wos | 000366591100056 | Publication Date | 2015-12-17 |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0036-8075 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 37.205 | Times cited | 281 | Open Access | |
| Notes | E.M. thanks the Fonds de Recherche du Québec–Nature et Technologies and ALISTORE–European Research Institute for funding this work, as well as the European community I3 networks for funding the neutron scattering research trip. This work was also funded by the Slovenian Research Agency research program P2-0148. This work is partially based on experiments performed at the Institut Laue Langevin. We thank J. Rodriguez-Carvajal for help with neutron scattering experiments and for fruitful discussions. We also thank M. T. Sougrati for performing the Sn-Mössbauer measurements. Use of the Advanced Photon Source at Argonne National Laboratory was supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, under contract no. DE-AC02- 06CH11357. M.S. and M.-L.D. acknowledge high-performance computational resources from GENCI-CCRT/CINES (grant cmm6691). J.-M.T. acknowledges funding from the European Research Council (ERC) (FP/2014-2020)/ERC Grant-Project670116-ARPEMA. | Approved | Most recent IF: 37.205; 2015 IF: 33.611 | ||
| Call Number | c:irua:130202 | Serial | 4005 | ||
| Permanent link to this record | |||||
| Author | Forsh, E.A.; Abakumov, A.M.; Zaytsev, V.B.; Konstantinova, E.A.; Forsh, P.A.; Rumyantseva, M.N.; Gaskov, A.M.; Kashkarov, P.K. | ||||
| Title | Optical and photoelectrical properties of nanocrystalline indium oxide with small grains | Type | A1 Journal article | ||
| Year |
2015 | Publication | Thin solid films : an international journal on the science and technology of thin and thick films | Abbreviated Journal | Thin Solid Films |
| Volume | 595 | Issue | 595 | Pages | 25-31 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Optical properties, spectral dependence of photoconductivity and photoconductivity decay in nanocrystalline indium oxide In2O3 are studied. A number of nanostructured In2O3 samples with various nanocrystals size are prepared by sol-gel method and characterized using various techniques. The mean nanocrystals size varies from 7 to 8 nm to 39-41 nm depending on the preparation conditions. Structural characterization of the In2O3 samples is performed by means of transmission electron microscopy and X-ray powder diffraction. The combined analysis of ultraviolet-visible absorption spectroscopy and diffuse reflectance spectroscopy shows that nanostructuring leads to the change in optical band gap: optical band gap of the In2O3 samples (with an average nanocrystal size from 7 to 41 nm) is equal to 2.8 eV. We find out the correlation between spectral dependence of photoconductivity and optical properties of nanocrystalline In2O3: sharp increase in photoconductivity was observed to begin at 2.8 eV that is equal to the optical bandgap in the In2O3 samples, and reached its maximum at 3.2-3.3 eV. The combined analysis of the slow photoconductivity decay in air, vacuum and argon, that was accurately fitted by a stretched-exponential function, and electron paramagnetic resonance (EPR) measurements shows that the kinetics of photoconductivity decay is strongly depended on the presence of oxygen molecules in the ambient of In2O3 nanocrystals. There is the quantitative correlation between EPR and photoconductivity data. Based on the obtained data we propose the model clearing up the phenomenon of permanent photoconductivity decay in nanocrystalline In2O3. (C) 2015 Elsevier B.V. All rights reserved. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Lausanne | Editor | ||
| Language | Wos | 000365812400005 | Publication Date | 2015-10-27 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0040-6090 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 1.879 | Times cited | 18 | Open Access | |
| Notes | Approved | Most recent IF: 1.879; 2015 IF: 1.759 | |||
| Call Number | UA @ lucian @ c:irua:130254 | Serial | 4219 | ||
| Permanent link to this record | |||||
| Author | Oueslati, S.; Brammertz, G.; Buffiere, M.; ElAnzeery, H.; Touayar, O.; Koeble, C.; Bekaert, J.; Meuris, M.; Poortmans, J. | ||||
| Title | Physical and electrical characterization of high-performance Cu2ZnSnSe4 based thin film solar cells | Type | A1 Journal article | ||
| Year |
2015 | Publication | Thin solid films : an international journal on the science and technology of thin and thick films | Abbreviated Journal | Thin Solid Films |
| Volume | 582 | Issue | 582 | Pages | 224-228 |
| Keywords | A1 Journal article; Condensed Matter Theory (CMT) | ||||
| Abstract | We report on the electrical, optical and physical properties of Cu2ZnSnSe4 solar cells using an absorber layer fabricated by selenization of sputtered Cu, Zn and Cu10Sn90 multilayers. A maximum active-area conversion efficiency of 10.4% under AM1.5G was measured with a maximum short circuit current density of 39.7 mA/cm(2), an open circuit voltage of 394 mV and a fill factor of 66.4%. We perform electrical and optical characterization using photoluminescence spectroscopy, external quantum efficiency, current-voltage and admittance versus temperature measurements in order to derive information about possible causes for the low open circuit voltage values observed. The main defects derived from these measurements are strong potential fluctuations in the absorber layer as well as a potential barrier of the order of 133 meV at the back side contact. (C) 2014 Elsevier B.V. All rights reserved. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Lausanne | Editor | ||
| Language | Wos | 000352225900048 | Publication Date | 2014-10-20 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0040-6090 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 1.879 | Times cited | 49 | Open Access | |
| Notes | ; We would like to acknowledge Tom De Geyter, Greetje Godiers, and Guido Huyberechts from Flamac in Gent for sputtering of the metal layers. AGC is acknowledged for providing substrates. This research is partially funded by the Flemish government, Department Economy, Science and Innovation. ; | Approved | Most recent IF: 1.879; 2015 IF: 1.759 | ||
| Call Number | UA @ lucian @ c:irua:132504 | Serial | 4225 | ||
| Permanent link to this record | |||||
| Author | Neyts, E.C. | ||||
| Title | The role of ions in plasma catalytic carbon nanotube growth : a review | Type | A1 Journal article | ||
| Year |
2015 | Publication | Frontiers of Chemical Science and Engineering | Abbreviated Journal | Front Chem Sci Eng |
| Volume | 9 | Issue | 9 | Pages | 154-162 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | While it is well-known that the plasma-enhanced catalytic chemical vapor deposition (PECVD) of carbon nanotubes (CNTs) offers a number of advantages over thermal CVD, the influence of the various individual contributing factors is not well understood. Especially the role of ions is unclear, since ions in plasmas are generally associated with sputtering rather than with growing a material. Even so, various studies have demonstrated the beneficial effects of ion bombardment during the growth of CNTs. This review looks at the role of the ions in plasma-enhanced CNT growth as deduced from both experimental and simulation studies. Specific attention is paid to the beneficial effects of ion bombardment. Based on the available literature, it can be concluded that ions can be either beneficial or detrimental for carbon nanotube growth, depending on the exact conditions and the control over the growth process. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000360319600003 | Publication Date | 2015-06-11 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2095-0179 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 1.712 | Times cited | 8 | Open Access | |
| Notes | Approved | Most recent IF: 1.712; 2015 IF: NA | |||
| Call Number | UA @ lucian @ c:irua:127815 | Serial | 4239 | ||
| Permanent link to this record | |||||
| Author | Vermeulen, M.; Sanyova, J.; Janssens, K. | ||||
| Title | Identification of artificial orpiment in the interior decorations of the Japanese tower in Laeken, Brussels, Belgium | Type | A1 Journal article | ||
| Year |
2015 | Publication | Heritage science | Abbreviated Journal | |
| Volume | 3 | Issue | Pages | Unsp 9 | |
| Keywords | A1 Journal article; Art; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation) | ||||
| Abstract | In this paper, we used a multi-technique approach in order to identify the arsenic sulfide pigment used in the decorative panels of the Japanese tower in Laeken, Belgium. Our attention was drawn to this particular pigment because of its relatively good conservation state, despite its known tendency to fade over time when exposed to light. The pigment was used with different painting techniques, bound with oil and urushi in the lacquers and with an aqueous binder in the mat relief panels. In the latter case it is always applied as an underlayer mixed with ultramarine blue. This quite unusual pigment mixture also shows a good state of preservation. In this study, the orpiment used for the Japanese tower has been identified as an amorphous arsenic sulfide glass (AsxSx) with the aid of light microscopy, PLM, SEM-EDX and Raman microscopy. The pigment features different degrees of As4S4 monomer units in its structure, also known as realgar-like nano-phases. This most likely indicates different synthesis processes as the formation of these As4S4 monomers is dependent of the quenching temperature (Tq) to which the artificial pigment is exposed during the preparation phase. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000356920400001 | Publication Date | 2015-02-25 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2050-7445 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | Times cited | 17 | Open Access | ||
| Notes | ; We cordially thank Gunter Grundmann for his precious advice regarding PLM and arsenic sulfide glass. This research is made possible with the support of the Belgian Science Policy Office (BELSPO) through the research program Science for a Sustainable Development – SDD, “Long-term role and fate of metal-sulfides in painted works of art – S2ART” (SD/RI/04A). ; | Approved | Most recent IF: NA | ||
| Call Number | UA @ admin @ c:irua:124904 | Serial | 5649 | ||
| Permanent link to this record | |||||
| Author | Anaf, W.; Bencs, L.; Van Grieken, R.; Janssens, K.; De Wael, K. | ||||
| Title | Indoor particulate matter in four Belgian heritage sites : case studies on the deposition of dark-colored and hygroscopic particles | Type | A1 Journal article | ||
| Year |
2015 | Publication | The science of the total environment | Abbreviated Journal | Sci Total Environ |
| Volume | 506 | Issue | Pages | 361-368 | |
| Keywords | A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation) | ||||
| Abstract | Atmospheric total suspended particulate (TSP) was passively sampled by means of deployed horizontal and vertical filters in various rooms of four Belgian cultural heritage buildings, installed with various heating/ventilation systems. Soiling/blackening and deposition of inorganic, water-soluble aerosol components were considered. The extent of soiling was determined by means of two independent methods: (1) in terms of the covering rate of the samplers by optical reflection microscopy and (2) the reduction in lightness of the samplers using the CIE L*a*b* color space by spectrophotometry. A fairly good correlation was found between both methods. The inorganic composition of the deposited water-soluble TSP was quantified by means of ion chromatography. Compared to controlled environments, uncontrolled environments showed increased water-soluble aerosol content of the total deposited mass. Higher chloride deposition was observed on horizontal surfaces, compared to vertical surfaces. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000347576800039 | Publication Date | 2014-11-24 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0048-9697 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 4.9 | Times cited | 12 | Open Access | |
| Notes | ; ; | Approved | Most recent IF: 4.9; 2015 IF: 4.099 | ||
| Call Number | UA @ admin @ c:irua:120640 | Serial | 5662 | ||
| Permanent link to this record | |||||
| Author | Alfeld, M.; Laurenze-Landsberg, C.; Denker, A.; Janssens, K.; Noble, P. | ||||
| Title | Neutron activation autoradiography and scanning macro-XRF of Rembrandt van Rijn's Susanna and the Elders (Gemaldegalerie Berlin) : a comparison of two methods for imaging of historical paintings with elemental contrast | Type | A1 Journal article | ||
| Year |
2015 | Publication | Applied physics A : materials science & processing | Abbreviated Journal | Appl Phys A-Mater |
| Volume | 119 | Issue | 3 | Pages | 795-805 |
| Keywords | A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation) | ||||
| Abstract | Imaging methods with elemental contrast are of great value for the investigation of historical paintings, as they allow for study of sub-surface layers that provide insight into a painting's creation process. Two of the most important methods are neutron activation autoradiography (NAAR) and scanning macro-XRF (MA-XRF). Given the differences between these methods in the fundamental physical phenomena exploited, a theoretical comparison of their capabilities is difficult and until now a critical comparison of their use on the same painting is missing. In this paper, we present a study of Rembrandt van Rijn's painting Susanna and the Elders from the Gemaldegalerie in Berlin employing both techniques. The painting features a considerable number of overpainted features and a wide range of pigments with different elemental tracers, including earth pigments (Mn/Fe), Azurite (Cu), lead white (Pb), vermilion (Hg) and smalt (Co, As). MA-XRF can detect all elements above Si (Z = 14), suffers from few spectral overlaps and can be performed in a few tens of hours in situ, i.e. in a museum. NAAR requires the stay of the painting at a research facility for several weeks, and inter-element interferences can be difficult to resolve. Also, only a limited number of elements contribute to the acquired autoradiographs, most notably Mn, Cu, As, Co, Hg and P. However, NAAR provides a higher lateral resolution and is less hindered by absorption in covering layers, which makes it the only method capable of visualizing P in lower paint layers. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000354189200001 | Publication Date | 2015-04-13 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0947-8396 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 1.455 | Times cited | 11 | Open Access | |
| Notes | ; This research was supported by the Interuniversity Attraction Poles Programme-Belgian Science Policy (IUAP VI/16). The text also presents the results of GOA “XANES meets ELNES” (Research Fund University of Antwerp, Belgium) and from FWO (Brussels, Belgium) Project Nos. G.0704.08 and G.01769.09. M. Alfeld received from 2009 to 2013 a PhD fellowship of the Research Foundation-Flanders (FWO). ; | Approved | Most recent IF: 1.455; 2015 IF: 1.704 | ||
| Call Number | UA @ admin @ c:irua:126034 | Serial | 5745 | ||
| Permanent link to this record | |||||
| Author | Rather, J.A.; Pilehvar, S.; De Wael, K. | ||||
| Title | Polycyclodextrin and carbon nanotubes as composite for tyrosinase immobilization and its superior electrocatalytic activity towards butylparaben an endocrine disruptor | Type | A1 Journal article | ||
| Year |
2015 | Publication | Journal of nanoscience and nanotechnology | Abbreviated Journal | |
| Volume | 15 | Issue | 5 | Pages | 3365-3372 |
| Keywords | A1 Journal article; Engineering sciences. Technology; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation) | ||||
| Abstract | We developed a protocol for the immobilization of tyrosinase (Tyr) on the composite of polycyclodextrin polymer (CDP) and carbon nanotubes for the detection of an endocrine disruptor, i.e., butylparaben (BP). The formation of the CDP polymer was characterized by UV-Vis spectrophotometry. The conducting film of cross-linked CDP and carbon nanotubes, displays excellent matrix capabilities for Tyr immobilization. The host-guest chemical reaction ability of CD and the ππ stacking interaction assure the bioactivity of Tyr towards butylparaben. The developed biosensor was characterized electrochemically by electrochemical impedance spectroscopy. The enzyme-substrate kinetic parameters such as the apparent Michaelis-Menten constant (K M app) was measured under saturated substrate concentration. The determination of butylparaben was carried out by using square wave voltammetry over the concentration range of 2.1 to 35.4 μM with a detection limit of 0.1 μM. The fabricated biosensor was successfully applied in real-life cosmetic samples with good recovery ranging from 98.5 to 102.8%. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000347435200007 | Publication Date | 2014-10-01 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1533-4899 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | Times cited | 3 | Open Access | ||
| Notes | ; The authors are highly thankful for the mobility grant (Non-Europe Postdoc Fellowship) for one of the author (Jahangir Ahmad Rather) supported by the Belgian Federal Science Policy (Belspo) co-funded by the Marie Curie Actions from the European Commission. Sanaz Pilehvar is funded by BOF-DOCPRO UA. ; | Approved | Most recent IF: NA | ||
| Call Number | UA @ admin @ c:irua:119550 | Serial | 5776 | ||
| Permanent link to this record | |||||
| Author | Trentelman, K.; Janssens, K.; van der Snickt, G.; Szafran, Y.; Woollett, A.T.; Dik, J. | ||||
| Title | Rembrandt's An Old Man in Military Costume: the underlying image re-examined | Type | A1 Journal article | ||
| Year |
2015 | Publication | Applied physics A : materials science & processing | Abbreviated Journal | Appl Phys A-Mater |
| Volume | 121 | Issue | 3 | Pages | 801-811 |
| Keywords | A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation) | ||||
| Abstract | The painting An Old Man in Military Costume in the J. Paul Getty Museum, by Rembrandt Harmensz van Rijn, was studied using two complementary, element-specific imaging techniques-neutron activation autoradiography (NAAR) and macro-X-ray fluorescence (MA-XRF) mapping-to reveal the second, hidden painting. NAAR provided a strong image of the face and cloak of the underlying figure, along with an indication of the chemical composition. The single-element distribution maps produced by MA-XRF mapping provided additional details into the shape of the underlying image and the composition of the pigments used. The underlying figure's face is richer in mercury, indicative of the pigment vermilion, than the face of the figure on the surface. Likewise, the cloak of the underlying figure is richer in copper than the surface figure though the identity of the copper-containing pigment cannot be determined from these data. The use of iron earth pigments, specifically Si-rich umbers, is indicated through the complementary information provided by the NAAR and MA-XRF maps. These data are used to create a false color digital reconstruction, yielding the most detailed representation of the underlying painting to date. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000364914100003 | Publication Date | 2015-08-31 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0947-8396 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 1.455 | Times cited | 22 | Open Access | |
| Notes | ; The authors gratefully acknowledge the assistance of all those who aided in the examination of this painting over the decades, that has culminated in the work presented here. Particular thanks go to Mark Leonard (former head of Paintings Conservation at the J. Paul Getty Museum) and Henry Prask (NIST) for carrying out the NAAR analysis; John Twilley (former GCI Scientist) for early investigations; Andrea Sartorius (former JPGM Paintings intern) for creating a mock-up painting used in earlier phases of this work; Peter Reishig (former GCI intern) for compiling the NAAR data; Catherine Patterson, Lynn Lee, and David Carson (GCI Science) and Gene Karraker (JPGM Paintings Conservation) for helping with the setup and operation of the M6 Jetstream; and Giacomo Chiari (former head of GCI Science) for performing the XRD analysis. Koen Janssens and Geert van der Snickt acknowledge the Fund Inbev-Baillet Latour for financial support. Joris Dik acknowledges the help of the Netherlands Organization for Scientific Research (NWO) in the form of a VIDI grant in the Innovational Research Incentive Scheme. ; | Approved | Most recent IF: 1.455; 2015 IF: 1.704 | ||
| Call Number | UA @ admin @ c:irua:130289 | Serial | 5812 | ||
| Permanent link to this record | |||||
| Author | Pouyet, E.; Cotte, M.; Fayard, B.; Salome, M.; Meirer, F.; Mehta, A.; Uffelman, E.S.; Hull, A.; Vanmeert, F.; Kieffer, J.; Burghammer, M.; Janssens, K.; Sette, F.; Mass, J. | ||||
| Title | 2D X-ray and FTIR micro-analysis of the degradation of cadmium yellow pigment in paintings of Henri Matisse | Type | A1 Journal article | ||
| Year |
2015 | Publication | Applied physics A : materials science & processing | Abbreviated Journal | |
| Volume | 121 | Issue | 3 | Pages | 967-980 |
| Keywords | A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation) | ||||
| Abstract | The chemical and physical alterations of cadmium yellow (CdS) paints in Henri Matisse's The Joy of Life (1905-1906, The Barnes Foundation) have been recognized since 2006, when a survey by portable X-ray fluorescence identified this pigment in all altered regions of the monumental painting. This alteration is visible as fading, discoloration, chalking, flaking, and spalling of several regions of light to medium yellow paint. Since that time, synchrotron radiation-based techniques including elemental and spectroscopic imaging, as well as X-ray scattering have been employed to locate and identify the alteration products observed in this and related works by Henri Matisse. This information is necessary to formulate one or multiple mechanisms for degradation of Matisse's paints from this period, and thus ensure proper environmental conditions for the storage and the display of his works. This paper focuses on 2D full-field X-ray Near Edge Structure imaging, 2D micro-X-ray Diffraction, X-ray Fluorescence, and Fourier Transform Infra-red imaging of the altered paint layers to address one of the long-standing questions about cadmium yellow alteration-the roles of cadmium carbonates and cadmium sulphates found in the altered paint layers. These compounds have often been assumed to be photo-oxidation products, but could also be residual starting reagents from an indirect wet process synthesis of CdS. The data presented here allow identifying and mapping the location of cadmium carbonates, cadmium chlorides, cadmium oxalates, cadmium sulphates, and cadmium sulphides in thin sections of altered cadmium yellow paints from The Joy of Life and Matisse's Flower Piece (1906, The Barnes Foundation). Distribution of various cadmium compounds confirms that cadmium carbonates and sulphates are photo-degradation products in The Joy of Life, whereas in Flower Piece, cadmium carbonates appear to have been a [(partially) unreacted] starting reagent for the yellow paint, a role previously suggested in other altered yellow paints. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000364914100017 | Publication Date | 2015-06-03 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0947-8396; 1432-0630 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | Times cited | Open Access | |||
| Notes | Approved | no | |||
| Call Number | UA @ admin @ c:irua:130290 | Serial | 7382 | ||
| Permanent link to this record | |||||
| Author | Van De Vijver, E.; Van Meirvenne, M.; Saey, T.; Delefortrie, S.; De Smedt, P.; De Pue, J.; Seuntjens, P. | ||||
| Title | Combining multi-receiver electromagnetic induction and stepped frequency ground penetrating radar for industrial site investigation | Type | A1 Journal article | ||
| Year |
2015 | Publication | European journal of soil science | Abbreviated Journal | |
| Volume | 66 | Issue | 4 | Pages | 688-698 |
| Keywords | A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) | ||||
| Abstract | The soil at industrial sites is frequently characterized by very heterogeneous properties, which are often related to physical disturbance and contamination. A conventional approach to characterize the soil, with only a limited number of invasive observations, fails to capture the full extent of soil heterogeneity. Proximal soil sensing provides efficient tools to record spatially dense soil information. Nevertheless, because the output of most sensors is affected by more than one soil property, the simultaneous characterization of different soil properties requires the use of multiple sensors. Here, we apply multi-receiver electromagnetic induction (EMI) and stepped frequency ground penetrating radar (GPR) to survey a former gasworks site in a seaport area of Belgium. We used the EMI and GPR sensors in a motorized system to obtain densely sampled measurements of apparent electrical conductivity, apparent magnetic susceptibility and contrasts in relative dielectric permittivity. Our study shows that the sensors give detailed information on the variation in these electromagnetic soil properties. Interpretation of the variation in terms of the stratification of the soil was hampered by localized anthropogenic disturbances. However, the sensors provided complementary information that enabled the identification, discrimination and accurate location of several of these localized disturbances, including underground utility services such as electric cables, buried structures such as the remains of foundations and contamination by salts. Because these represent typical targets in industrial site investigation, we conclude that multi-receiver EMI and stepped frequency GPR provide a useful set of tools to expedite the investigation of industrial sites. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000357341900008 | Publication Date | 2015-02-27 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1351-0754 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | Times cited | Open Access | |||
| Notes | Approved | no | |||
| Call Number | UA @ admin @ c:irua:127112 | Serial | 7684 | ||
| Permanent link to this record | |||||
| Author | Tirez, K.; Vanhoof, C.; Bronders, J.; Seuntjens, P.; Bleux, N.; Berghmans, P.; De Brucker, N.; Vanhaecke, F. | ||||
| Title | Do ICP-MS based methods fulfill the EU monitoring requirements for the determination of elements in our environment? | Type | A1 Journal article | ||
| Year |
2015 | Publication | Environmental science : processes & impacts | Abbreviated Journal | |
| Volume | 17 | Issue | 12 | Pages | 2034-2050 |
| Keywords | A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) | ||||
| Abstract | Undoubtedly, the most important advance in the environmental regulatory monitoring of elements of the last decade is the widespread introduction of ICP-mass spectrometry (ICP-MS) due to standards developed by the European Committee for Standardization. The versatility of ICP-MS units as a tool for the determination of major, minor and trace elements (Al, As, Ba, Ca, Cd, Co, Cr, Cu, Fe, Hg, K, Mg, Mn, Mo, Na, Ni, P, Pb, Sb, Se, Sn, Ti, V and Zn) in surface water, groundwater, river sediment, topsoil, subsoil, fine particulates and atmospheric deposition is illustrated in this paper. Ranges of background concentrations for major, minor and trace elements obtained from a regional case study (Flanders, Belgium) are summarized for all of these environmental compartments and discussed in the context of a harmonized implementation of European regulatory monitoring requirements. The results were derived from monitoring programs in support of EU environmental quality directives and were based on a selection of (non-polluted) background locations. Because of the availability of ICP-MS instruments nowadays, it can be argued that the main hindrance for meeting the European environmental monitoring requirements is no longer the technical feasibility of analysis at these concentration levels, but rather (i) potential contamination during sampling and analysis, (ii) too limited implementation of quality control programs, validating the routinely applied methods (including sampling and low level verification) and (iii) lack of harmonization in reporting of the chemical environmental status between the individual member states. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000365915600005 | Publication Date | 2015-10-06 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2050-7887; 2050-7895 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | Times cited | Open Access | |||
| Notes | Approved | no | |||
| Call Number | UA @ admin @ c:irua:130316 | Serial | 7821 | ||
| Permanent link to this record | |||||
| Author | Saha, S.; Badhe, N.; Seuntjens, D.; Vlaeminck, S.E.; Biswas, R.; Nandy, T. | ||||
| Title | Effective carbon and nutrient treatment solutions for mixed domestic-industrial wastewater in India | Type | A1 Journal article | ||
| Year |
2015 | Publication | Water science and technology | Abbreviated Journal | |
| Volume | 72 | Issue | 4 | Pages | 651-657 |
| Keywords | A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) | ||||
| Abstract | The present study evaluates effectiveness of up-flow anaerobic sludge blanket (UASB) reactor followed by two post-anaerobic treatment options, namely free-surface, up-flow constructed wetland (FUP-CW) and oxygen-limited anaerobic nitrification/denitrification (OLAND) processes in treating sewage from the peri-urban areas in India receiving illegal industrial infiltrations. The UASB studies yielded robust results towards fluctuating strength of sewage and consistently removed 87-98% chemical oxygen demand (COD) at a hydraulic retention time of 1.5-2 d. The FUP-CW removed 68.5 +/- 13% COD, 68 +/- 3% NH4+-N, 38 +/- 5% PO43--P, 97.6 +/- 5% suspended particles and 97 +/- 13% fecal coliforms. Nutrient removal was found to be limiting in FUP-CW, especially in winter. Nitrogen removal in the OLAND process were 100 times higher than the FUP-CW process. Results show that UASB followed by FUP-CW can be an excellent, decentralized sewage treatment option, except during winter when nutrient removal is limited in FUP-CW. Hence, the study proposes bio-augmentation of FUP-CW with OLAND biomass for overall improvement in the performance of UASB followed by FUP-CW process. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000359387200019 | Publication Date | 2015-08-06 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0273-1223; 1996-9732 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | Times cited | Open Access | |||
| Notes | Approved | no | |||
| Call Number | UA @ admin @ c:irua:127775 | Serial | 7840 | ||
| Permanent link to this record | |||||
| Author | Baken, S.; Salaets, P.; Desmet, N.; Seuntjens, P.; Vanlierde, E.; Smolders, E. | ||||
| Title | Oxidation of iron causes removal of phosphorus and arsenic from streamwater in groundwater-fed lowland catchments | Type | A1 Journal article | ||
| Year |
2015 | Publication | Environmental science and technology | Abbreviated Journal | |
| Volume | 49 | Issue | 5 | Pages | 2886-2894 |
| Keywords | A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) | ||||
| Abstract | The fate of iron (Fe) may affect that of phosphorus (P) and arsenic (As) in natural waters. This study addresses the removal of Fe, P, and As from streams in lowland catchments fed by reduced, Fe-rich groundwater (average: 20 mg Fe L-1). The concentrations of dissolved Fe (<0.45 mu m) in streams gradually decrease with increasing hydraulic residence time (travel time) of the water in the catchment. The removal of Fe from streamwater is governed by chemical reactions and hydrological processes: the oxidation of ferrous iron (Fe(II)) and the subsequent formation of particulate Fe oxyhydroxides proceeds as the water flows through the catchment into increasingly larger streams. The Fe removal exhibits first-order kinetics with a mean half-life of 12 h, a value in line with predictions by a kinetic model for Fe(II) oxidation. The Fe concentrations in streams vary seasonally: they are higher in winter than in summer, due to shorter hydraulic residence time and lower temperature in winter. The removal of P and As is much faster than that of Fe. The average concentrations of P and As in streams (42 mu g P L-1) and 1.4 mu g As L-1) are 1 order of magnitude below those in groundwater (393 mu g P L-1 and 17 mu g As L-1). This removal is attributed to fast sequestration by oxidizing Fe when the water enters oxic environments, possibly by adsorption on Fe oxyhydroxides or by formation of ferric phosphates. The average P and As concentrations in groundwater largely exceed local environmental limits for freshwater (140 mu g P L-1 and 3 mu g As L((-1)), but in streams, they are below these limits. Naturally occurring Fe in groundwater may alleviate the environmental risk associated with P and As in the receiving streams. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000350611100040 | Publication Date | 2015-02-06 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0013-936x; 1520-5851 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | Times cited | Open Access | |||
| Notes | Approved | no | |||
| Call Number | UA @ admin @ c:irua:125409 | Serial | 8354 | ||
| Permanent link to this record | |||||
| Author | Tang, T.; Boenne, W.; Desmet, N.; Seuntjens, P.; Bronders, J.; van Griensven, A. | ||||
| Title | Quantification and characterization of glyphosate use and loss in a residential area | Type | A1 Journal article | ||
| Year |
2015 | Publication | The science of the total environment | Abbreviated Journal | |
| Volume | 517 | Issue | Pages | 207-214 | |
| Keywords | A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) | ||||
| Abstract | Urban runoff can be a significant source of pesticides in urban streams. However, quantification of this source has been difficult because pesticide use by urban residents (e.g., on pavements or in gardens) is often unknown, particularly at the scale of a residential catchment. Proper quantification and characterization of pesticide loss via urban runoff require sound information on the use and occurrence of pesticides at hydrologically-relevant spatial scales, involving various hydrological conditions. We conducted a monitoring study in a residential area (9.5 ha, Flanders, Belgium) to investigate the use and loss of a widely-used herbicide (glyphosate) and its major degradation product (aminomethylphosphonic acid, AMPA). The study covered 13 rainfall events over 67 days. Overall, less than 0.5% of glyphosate applied was recovered from the storm drain outflow in the catchment. Maximum detected concentrations were 6.1 mu g/L and 5.8 mu g/L for glyphosate and AMPA, respectively, both of which are below the predicted no-effect concentration for surface water proposed by the Flemish environmental agency (10 mu g/L), but are above the EU drinking water standard (0.1 mu g/L). The measured concentrations and percentage loss rates can be attributed partially to the strong sorption capacity of glyphosate and low runoff potential in the study area. However, glyphosate loss varied considerably among rainfall events and event load of glyphosate mass was mainly controlled by rainfall amount, according to further statistical analyses. To obtain urban pesticide management insights, robust tools are required to investigate the loss and occurrence of pesticides influenced by various factors, particularly the hydrological and spatial factors. (C) 2015 Elsevier B.V. All rights reserved. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000352663800020 | Publication Date | 2015-02-27 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0048-9697; 1879-1026 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | Times cited | Open Access | |||
| Notes | Approved | no | |||
| Call Number | UA @ admin @ c:irua:125992 | Serial | 8431 | ||
| Permanent link to this record | |||||
| Author | Van de Vijver, E.; Van Meirvenne, M.; Vandenhaute, L.; Delefortrie, S.; De Smedt, P.; Saey, T.; Seuntjens, P. | ||||
| Title | Urban soil exploration through multi-receiver electromagnetic induction and stepped-frequency ground penetrating radar | Type | A1 Journal article | ||
| Year |
2015 | Publication | Environmental science : processes & impacts | Abbreviated Journal | |
| Volume | 17 | Issue | 7 | Pages | 1271-1281 |
| Keywords | A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) | ||||
| Abstract | In environmental assessments, the characterization of urban soils relies heavily on invasive investigation, which is often insufficient to capture their full spatial heterogeneity. Non-invasive geophysical techniques enable rapid collection of high-resolution data and provide a cost-effective alternative to investigate soil in a spatially comprehensive way. This paper presents the results of combining multi-receiver electromagnetic induction and stepped-frequency ground penetrating radar to characterize a former garage site contaminated with petroleum hydrocarbons. The sensor combination showed the ability to identify and accurately locate building remains and a high-density soil layer, thus demonstrating the high potential to investigate anthropogenic disturbances of physical nature. In addition, a correspondence was found between an area of lower electrical conductivity and elevated concentrations of petroleum hydrocarbons, suggesting the potential to detect specific chemical disturbances. We conclude that the sensor combination provides valuable information for preliminary assessment of urban soils. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000357793300008 | Publication Date | 2015-06-04 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2050-7887; 2050-7895 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | Times cited | Open Access | |||
| Notes | Approved | no | |||
| Call Number | UA @ admin @ c:irua:127130 | Serial | 8715 | ||
| Permanent link to this record | |||||
| Author | Gong, X.; Marmy, P.; Volodin, A.; Amin-Ahmadi, B.; Qin, L.; Schryvers, D.; Gavrilov, S.; Stergar, E.; Verlinden, B.; Wevers, M.; Seefeldt, M. | ||||
| Title | Multiscale investigation of quasi-brittle fracture characteristics in a 9Cr–1Mo ferritic–martensitic steel embrittled by liquid lead–bismuth under low cycle fatigue | Type | A1 Journal article | ||
| Year |
2016 | Publication | Corrosion science | Abbreviated Journal | |
| Volume | 102 | Issue | 102 | Pages | 137-152 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Liquid metal embrittlement (LME) induced quasi-brittle fracture characteristics of a 9Cr–1Mo ferritic–martensitic steel (T91) after fatigue cracking in lead–bismuth eutectic (LBE) have been investigated at various length scales. The results show that the LME fracture morphology is primarily characterized by quasi-brittle translath flat regions partially covered by nanodimples, shallow secondary cracks propagating along the martensitic lath boundaries as well as tear ridges covered by micro dimples. These diverse LME fracture features likely indicate a LME mechanism involving multiple physical processes, such as weakening induced interatomic decohesion at the crack tip and plastic shearing induced nano/micro voiding in the plastic zone. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000367275700014 | Publication Date | 2015-10-22 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0010938X | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | Times cited | 16 | Open Access | ||
| Notes | The work is financially supported by the MYRRHA project,SCK•CEN, Belgium and partly funded by the European AtomicEnergy Community’s (Euratom) Seventh Framework ProgrammeFP7/2007-2013 under grant agreement No. 604862 (MatISSEproject) and in the framework of the EERA (European EnergyResearch Alliance) Joint Programme on Nuclear Materials. Dr. TomVan der Donck (KU Leuven) is acknowledged for the EBSD mea-surements. The authors are grateful to Dr. Van Renterghem Wouter(SCK•CEN) for fruitful discussion of the TEM results. Xing Gongsincerely acknowledges valuable suggestions from Dr. S.P. Lynch(Defence Science and Technology Organisation and Monash Uni-versity, Melbourne, Australia). | Approved | Most recent IF: NA | ||
| Call Number | c:irua:129997 | Serial | 4013 | ||
| Permanent link to this record | |||||
| Author | Van Laer, K.; Bogaerts, A. | ||||
| Title | Fluid modelling of a packed bed dielectric barrier discharge plasma reactor | Type | A1 Journal article | ||
| Year |
2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 015002 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | A packed bed dielectric barrier discharge plasma reactor is computationally studied with a fluid model. Two different complementary axisymmetric 2D geometries are used to mimic the intrinsic 3D problem. It is found that a packing enhances the electric field strength and electron temperature at the contact points of the dielectric material due to polarization of the beads by the applied potential. As a result, these contact points prove to be of direct importance to initiate the plasma. At low applied potential, the discharge stays at the contact points, and shows the properties of a Townsend discharge. When a high enough potential is applied, the plasma will be able to travel through the gaps in between the beads from wall to wall, forming a kind of glow discharge. Therefore, the inclusion of a so-called ‘channel of voids’ is indispensable in any type of packed bed modelling. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000370974800009 | Publication Date | 2015-12-01 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 50 | Open Access | |
| Notes | The authors gratefully thank St Kolev for the many interesting discussions and the useful advise in setting up the models. This research was carried out in the framework of the network on Physical Chemistry of Plasma-Surface Interactions— Interuniversity Attraction Poles, phase VII (http://psi-iap7.ulb. ac.be/), and supported by the Belgian Science Policy Office (BELSPO). K Van Laer is indebted to the Institute for the Promotion of Innovation by Science and Technology in Flanders (IWT Flanders) for financial support. | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:129802 | Serial | 3982 | ||
| Permanent link to this record | |||||
| Author | Van der Paal, J.; Neyts, E.C.; Verlackt, C.C.W.; Bogaerts, A. | ||||
| Title | Effect of lipid peroxidation on membrane permeability of cancer and normal cells subjected to oxidative stress | Type | A1 Journal article | ||
| Year |
2016 | Publication | Chemical science | Abbreviated Journal | Chem Sci |
| Volume | 7 | Issue | 7 | Pages | 489-498 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | We performed molecular dynamics simulations to investigate the effect of lipid peroxidation products on the structural and dynamic properties of the cell membrane. Our simulations predict that the lipid order in a phospholipid bilayer, as a model system for the cell membrane, decreases upon addition of lipid peroxidation products. Eventually, when all phospholipids are oxidized, pore formation can occur. This will allow reactive species, such as reactive oxygen and nitrogen species (RONS), to enter the cell and cause oxidative damage to intracellular macromolecules, such as DNA or proteins. On the other hand, upon increasing the cholesterol fraction of lipid bilayers, the cell membrane order increases, eventually reaching a certain threshold, from which cholesterol is able to protect the membrane against pore formation. This finding is crucial for cancer treatment by plasma technology, producing a large number of RONS, as well as for other cancer treatment methods that cause an increase in the concentration of extracellular RONS. Indeed, cancer cells contain less cholesterol than their healthy counterparts. Thus, they will be more vulnerable to the consequences of lipid peroxidation, eventually enabling the penetration of RONS into the interior of the cell, giving rise to oxidative stress, inducing pro-apoptotic factors. This provides, for the first time, molecular level insight why plasma can selectively treat cancer cells, while leaving their healthy counterparts undamaged, as is indeed experimentally demonstrated. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000366826900058 | Publication Date | 2015-10-16 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2041-6520 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 8.668 | Times cited | 106 | Open Access | |
| Notes | The authors acknowledge nancial support from the Fund for Scientic Research (FWO) Flanders, grant number G012413N. The calculations were performed in part using the Turing HPC infrastructure of the CalcUA core facility of the Universiteit Antwerpen, a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the Universiteit Antwerpen. | Approved | Most recent IF: 8.668 | ||
| Call Number | c:irua:131058 | Serial | 3986 | ||
| Permanent link to this record | |||||
| Author | Belov, I.; Paulussen, S.; Bogaerts, A. | ||||
| Title | Appearance of a conductive carbonaceous coating in a CO2dielectric barrier discharge and its influence on the electrical properties and the conversion efficiency | Type | A1 Journal article | ||
| Year |
2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 015023 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | This work examines the properties of a dielectric barrier discharge (DBD) reactor, built for CO2 decomposition, by means of electrical characterization, optical emission spectroscopy and gas chromatography. The discharge, formed in an electronegative gas (such as CO2, but also O2), exhibits clearly different electrical characteristics, depending on the surface conductivity of the reactor walls. An asymmetric current waveform is observed in the metaldielectric (MD) configuration, with sparse high-current pulses in the positive half-cycle (HC) and a more uniform regime in the negative HC. This indicates that the discharge is operating in two alternating regimes with rather different properties. At high CO2 conversion regimes, a conductive coating is deposited on the dielectric. This so-called coated MD configuration yields a symmetric current waveform, with current peaks in both the positive and negative HCs. In a double-dielectric (DD) configuration, the current waveform is also symmetric, but without current peaks in both the positive and negative HC. Finally, the DD configuration with conductive coating on the inner surface of the outer dielectric, i.e. so-called coated DD, yields again an asymmetric current waveform, with current peaks in the negative HC. These different electrical characteristics are related to the presence of the conductive coating on the dielectric wall of the reactor and can be explained by an increase of the local barrier capacitance available for charge transfer. The different discharge regimes affect the CO2 conversion, more specifically, the CO2 conversion is lowest in the clean DD configuration. It is somewhat higher in the coated DD configuration, and still higher in the MD configuration. The clean and coated MD configuration, however, gave similar CO2 conversion. These results indicate that the conductivity of the dielectric reactor walls can highly promote the development of the high-amplitude discharge current pulses and subsequently the CO2 conversion. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000370974800030 | Publication Date | 2016-01-21 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 25 | Open Access | |
| Notes | The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7-PEOPLE-2013-ITN) under Grant Agreement № 606889 (RAPID—Reactive Atmospheric Plasma processIng—eDucation network). | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:130790 | Serial | 4006 | ||
| Permanent link to this record | |||||
| Author | Snoeckx, R.; Heijkers, S.; Van Wesenbeeck, K.; Lenaerts, S.; Bogaerts, A. | ||||
| Title | CO2conversion in a dielectric barrier discharge plasma: N2in the mix as a helping hand or problematic impurity? | Type | A1 Journal article | ||
| Year |
2016 | Publication | Energy & environmental science | Abbreviated Journal | Energ Environ Sci |
| Volume | 9 | Issue | 9 | Pages | 999-1011 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT); Sustainable Energy, Air and Water Technology (DuEL) | ||||
| Abstract | Carbon dioxide conversion and utilization has gained significant interest over the years. A novel gas conversion technique with great potential in this area is plasma technology. A lot of research has already been performed, but mostly on pure gases. In reality, N2 will always be an important impurity in effluent gases. Therefore, we performed an extensive combined experimental and computational study on the effect of N2 in the range of 1–98% on CO2 splitting in dielectric barrier discharge (DBD) plasma. The presence of up to 50% N2 in the mixture barely influences the effective (or overall) CO2 conversion and energy efficiency, because the N2 metastable molecules enhance the absolute CO2 conversion, and this compensates for the lower CO2 fraction in the mixture. Higher N2 fractions, however, cause a drop in the CO2 conversion and energy efficiency. Moreover, in the entire CO2/N2 mixing ratio, several harmful compounds, i.e., N2O and NOx compounds, are produced in the range of several 100 ppm. The reaction pathways for the formation of these compounds are explained based on a kinetic analysis, which allows proposing solutions on how to prevent the formation of these harmful compounds. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000372243600030 | Publication Date | 2015-12-15 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1754-5692 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 29.518 | Times cited | 68 | Open Access | |
| Notes | The authors acknowledge financial support from the IAP/7 (Inter-university Attraction Pole) program ‘PSI-Physical Chemistry of Plasma-Surface Interactions’, financially supported by the Belgian Federal Office for Science Policy (BELSPO), as well as the Fund for Scientific Research Flanders (FWO). This work was carried out in part using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen, a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the University of Antwerp. | Approved | Most recent IF: 29.518 | ||
| Call Number | c:irua:133169 | Serial | 4020 | ||
| Permanent link to this record | |||||
| Author | Ozkan, A.; Dufour, T.; Silva, T.; Britun, N.; Snyders, R.; Bogaerts, A.; Reniers, F. | ||||
| Title | The influence of power and frequency on the filamentary behavior of a flowing DBD—application to the splitting of CO2 | Type | A1 Journal article | ||
| Year |
2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 025013 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | In this experimental study, a flowing dielectric barrier discharge operating at atmospheric pressure is used for the splitting of CO2 into O2 and CO. The influence of the applied frequency and plasma power on the microdischarge properties is investigated to understand their role on the CO2 conversion. Electrical measurements are carried out to explain the conversion trends and to characterize the microdischarges through their number, their lifetime, their intensity and the induced electrical charge. Their influence on the gas and electrode temperatures is also evidenced through optical emission spectroscopy and infrared imaging. It is shown that, in our configuration, the conversion depends mostly on the charge delivered in the plasma and not on the effective plasma voltage when the applied power is modified. Similarly, at constant total current, a better conversion is observed at low frequencies, where a less filamentary discharge regime with a higher effective plasma voltage than that at a higher frequency is obtained. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000372337900015 | Publication Date | 2016-02-25 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 40 | Open Access | |
| Notes | The authors acknowledge financial support from the IAPVII/ 12, P7/34 (Inter-university Attraction Pole) program ‘PSI-Physical Chemistry of Plasma-Surface Interactions’, financially supported by the Belgian Federal Office for Science Policy (BELSPO). A Ozkan would like to thank the financial support given by ‘Fonds David et Alice Van Buuren’. N Britun is a postdoctoral researcher of the F.R.S.-FNRS, Belgium. | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:131904 | Serial | 4021 | ||
| Permanent link to this record | |||||
| Author | Filez, M.; Redekop, E.A.; Poelman, H.; Galvita, V.V.; Meledina, M.; Turner, S.; Van Tendeloo, G.; Detavernier, C.; Marin, G.B. | ||||
| Title | One-pot synthesis of Pt catalysts based on layered double hydroxides: an application in propane dehydrogenation | Type | A1 Journal article | ||
| Year |
2016 | Publication | Catalysis science & technology | Abbreviated Journal | Catal Sci Technol |
| Volume | 6 | Issue | 6 | Pages | 1863-1869 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Simple methods for producing noble metal catalysts with well-defined active sites and improved performance are highly desired in the chemical industry. However, the development of such methods still presents a formidable synthetic challenge. Here, we demonstrate a one-pot synthesis route for the controlled production of bimetallic Pt–In catalysts based on the single-step formation of Mg,Al,Pt,In-containing layered double hydroxides (LDHs). Besides their simple synthesis, these Pt–In catalysts exhibit superior propane dehydrogenation activity compared to their multi-step synthesized analogs. The presented material serves as a showcase for the one-pot synthesis of a broader class of LDH-derived mono- and multimetallic Pt catalysts. The compositional flexibility provided by LDH materials can pave the way towards highperforming Pt-based catalysts with tunable physicochemical properties. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000372172800031 | Publication Date | 2015-10-23 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2044-4753 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 5.773 | Times cited | 12 | Open Access | |
| Notes | This work was supported by the Fund for Scientific Research Flanders (FWO: G.0209.11), the ‘Long Term Structural Methusalem Funding by the Flemish Government’, the IAP 7/05 Interuniversity Attraction Poles Programme – Belgian State – Belgian Science Policy, and the Fund for Scientific Research Flanders (FWO-Vlaanderen) by supplying financing of beam time at the DUBBLE beamline of the ESRF and travel costs and a post-doctoral fellowship for S. T. The authors acknowledge the assistance from the DUBBLE (XAS campaign 26-01-979) and SuperXAS staff (Proposal 20131191). E. A. Redekop acknowledges the Marie Curie International Incoming Fellowship granted by the European Commission (Grant Agreement No. 301703). The authors also express their gratitude to O. Janssens for performing ex situ XRD characterization. | Approved | Most recent IF: 5.773 | ||
| Call Number | c:irua:133167 | Serial | 4057 | ||
| Permanent link to this record | |||||
| Author | Trenchev, G.; Kolev, S.; Bogaerts, A. | ||||
| Title | A 3D model of a reverse vortex flow gliding arc reactor | Type | A1 Journal article | ||
| Year |
2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 035014 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | In this computational study, a gliding arc plasma reactor with a reverse-vortex flow stabilization is modelled for the first time by a fluid plasma description. The plasma reactor operates with argon gas at atmospheric pressure. The gas flow is simulated using the k-ε Reynolds-averaged Navier–Stokes turbulent model. A quasi-neutral fluid plasma model is used for computing the plasma properties. The plasma arc movement in the reactor is observed, and the results for the gas flow, electrical characteristics, plasma density, electron temperature, and gas temperature are analyzed. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000376557400022 | Publication Date | 2016-04-09 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 20 | Open Access | |
| Notes | This research was carried out in the framework of the network on Physical Chemistry of Plasma–Surface Interactions— Interuniversity Attraction Poles, phase VII (http://psi-iap7.ulb. ac.be/), and supported by the Belgian Science Policy Office (BELSPO), and it was also funded by the Fund for Scientific Research Flanders (FWO). Grant number: 11U5316N. | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:132888 c:irua:132888 | Serial | 4063 | ||
| Permanent link to this record | |||||
| Author | Ozkan, A.; Dufour, T.; Bogaerts, A.; Reniers, F. | ||||
| Title | How do the barrier thickness and dielectric material influence the filamentary mode and CO2conversion in a flowing DBD? | Type | A1 Journal article | ||
| Year |
2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 045016 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Dielectric barrier discharges (DBDs) are commonly used to generate cold plasmas at atmospheric pressure. Whatever their configuration (tubular or planar), the presence of a dielectric barrier is mandatory to prevent too much charge build up in the plasma and the formation of a thermal arc. In this article, the role of the barrier thickness (2.0, 2.4 and 2.8 mm) and of the kind of dielectric material (alumina, mullite, pyrex, quartz) is investigated on the filamentary behavior in the plasma and on the CO2 conversion in a tubular flowing DBD, by means of mass spectrometry measurements correlated with electrical characterization and IR imaging. Increasing the barrier thickness decreases the capacitance, while preserving the electrical charge. As a result, the voltage over the dielectric increases and a larger number of microdischarges is generated, which enhances the CO2 conversion. Furthermore, changing the dielectric material of the barrier, while keeping the same geometry and dimensions, also affects the CO2 conversion. The highest CO2 conversion and energy efficiency are obtained for quartz and alumina, thus not following the trend of the relative permittivity. From the electrical characterization, we clearly demonstrate that the most important parameters are the somewhat higher effective plasma voltage (yielding a somewhat higher electric field and electron energy in the plasma) for quartz, as well as the higher plasma current (and thus larger electron density) and the larger number of microdischarge filaments (mainly for alumina, but also for quartz). The latter could be correlated to the higher surface roughness for alumina and to the higher voltage over the dielectric for quartz. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000380380200030 | Publication Date | 2016-06-30 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 24 | Open Access | |
| Notes | The authors acknowledge financial support from the IAPVII/ 12, P7/34 (Inter-university Attraction Pole) program ‘PSI-Physical Chemistry of Plasma-Surface Interactions’, financially supported by the Belgian Federal Office for Science Policy (BELSPO). A. Ozkan would like to thank the financial support given by ‘Fonds David et Alice Van Buuren’. | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:134396 | Serial | 4100 | ||
| Permanent link to this record | |||||
| Author | Berthelot, A.; Bogaerts, A. | ||||
| Title | Modeling of plasma-based CO2conversion: lumping of the vibrational levels | Type | A1 Journal article | ||
| Year |
2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 045022 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Although CO2 conversion by plasma technology is gaining increasing interest, the underlying mechanisms for an energy-efficient process are still far from understood. In this work, a reduced non-equilibrium CO2 plasma chemistry set, based on level lumping of the vibrational levels, is proposed and the reliability of this level-lumping method is tested by a self-consistent zero-dimensional code. A severe reduction of the number of equations to be solved is achieved, which is crucial to be able to model non-equilibrium CO2 plasmas by 2-dimensional models. Typical conditions of pressure and power used in a microwave plasma for CO2 conversion are investigated. Several different sets, using different numbers of lumped groups, are considered. The lumped models with 1, 2 or 3 groups are able to reproduce the gas temperature, electron density and electron temperature profiles, as calculated by the full model treating all individual excited levels, in the entire pressure range investigated. Furthermore, a 3-groups model is also able to reproduce the shape of the vibrational distribution function (VDF) and gives the most reliable prediction of the CO2 conversion. A strong influence of the vibrational excitation on the plasma characteristics is observed. Finally, the limitations of the lumped-levels method are discussed. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000380380200036 | Publication Date | 2016-07-08 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 33 | Open Access | |
| Notes | This project has received funding from the European Union’s Seventh Framework Programme for research, technological development and demonstration under grant agreement no 606889 and it was also carried out in the framework of the network on Physical Chemistry of Plasma-Surface Interactions—Interuniversity Attraction Poles, phase VII (PSI-IAP7) supported by the Belgian Science Policy Office (BELSPO). The computational work was carried out using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UA), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UA. | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:134397 | Serial | 4101 | ||
| Permanent link to this record | |||||
| Author | Bal, K.M.; Neyts, E.C. | ||||
| Title | Direct observation of realistic-temperature fuel combustion mechanisms in atomistic simulations | Type | A1 Journal article | ||
| Year |
2016 | Publication | Chemical science | Abbreviated Journal | Chem Sci |
| Volume | 7 | Issue | 7 | Pages | 5280-5286 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Atomistic simulations can in principle provide an unbiased description of all mechanisms, intermediates, and products of complex chemical processes. However, due to the severe time scale limitation of conventional simulation techniques, unrealistically high simulation temperatures are usually applied, which are a poor approximation of most practically relevant low-temperature applications. In this work, we demonstrate the direct observation at the atomic scale of the pyrolysis and oxidation of n-dodecane at temperatures as low as 700 K through the use of a novel simulation technique, collective variable-driven hyperdynamics (CVHD). A simulated timescale of up to 39 seconds is reached. Product compositions and dominant mechanisms are found to be strongly temperature-dependent, and are consistent with experiments and kinetic models. These simulations provide a first atomic-level look at the full dynamics of the complicated fuel combustion process at industrially relevant temperatures and time scales, unattainable by conventional molecular dynamics simulations. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000380893900059 | Publication Date | 2016-05-05 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2041-6520 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 8.668 | Times cited | 22 | Open Access | |
| Notes | K. M. B. is funded as PhD fellow (aspirant) of the FWO-Flanders (Fund for Scientic Research-Flanders), Grant 11V8915N. The computational resources and services used in this work were provided by the VSC (Flemish Supercomputer Center) and the HPC infrastructure of the University of Antwerp (CalcUA), funded by the Hercules Foundation and the Flemish Government – department EWI. The authors would also like to thank S. Banerjee for assisting with the interpretation of the experimental results. | Approved | Most recent IF: 8.668 | ||
| Call Number | c:irua:134577 c:irua:135670 | Serial | 4105 | ||
| Permanent link to this record | |||||
| Author | Ozkan, A.; Dufour, T.; Silva, T.; Britun, N.; Snyders, R.; Reniers, F.; Bogaerts, A. | ||||
| Title | DBD in burst mode: solution for more efficient CO2conversion? | Type | A1 Journal article | ||
| Year |
2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 055005 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | CO2 conversion into value-added products has gained significant interest over the few last years, as the greenhouse gas concentrations constantly increase due to anthropogenic activities. Here we report on experiments for CO2 conversion by means of a cold atmospheric plasma using a cylindrical flowing dielectric barrier discharge (DBD) reactor. A detailed comparison of this DBD ignited in a so-called burst mode (i.e. where an AC voltage is applied during a limited amount of time) and pure AC mode is carried out to evaluate their effect on the conversion of CO2 as well as on the energy efficiency. Decreasing the duty cycle in the burst mode from 100% (i.e. corresponding to pure AC mode) to 40% leads to a rise in the conversion from 16–26% and to a rise in the energy efficiency from 15 to 23%. Based on a detailed electrical analysis, we show that the conversion correlates with the features of the microfilaments. Moreover, the root-mean-square voltage in the burst mode remains constant as a function of the process time for the duty cycles <70%, while a higher duty cycle or the usual pure AC mode leads to a clear voltage decay by more than 500 V, over approximately 90 s, before reaching a steady state regime. The higher plasma voltage in the burst mode yields a higher electric field. This causes the increasing the electron energy, and therefore their involvement in the CO2 dissociation process, which is an additional explanation for the higher CO2 conversion and energy efficiency in the burst mode. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000403945500005 | Publication Date | 2016-08-02 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 17 | Open Access | |
| Notes | The authors acknowledge financial support from the IAPVII/ 12, P7/34 (Inter-university Attraction Pole) program ‘PSI-Physical Chemistry of Plasma-Surface Interactions’, financially supported by the Belgian Federal Office for Science Policy (BELSPO). A. Ozkan would also like to thank financial support given by ‘Fonds David et Alice Van Buuren’. | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:134841 | Serial | 4107 | ||
| Permanent link to this record | |||||