| Home | << 1 2 3 4 5 6 7 8 9 10 11 12 13 >> |
|
| Records | |||||
|---|---|---|---|---|---|
| Author | Ozkan, A.; Dufour, T.; Silva, T.; Britun, N.; Snyders, R.; Bogaerts, A.; Reniers, F. | ||||
| Title | The influence of power and frequency on the filamentary behavior of a flowing DBD—application to the splitting of CO2 | Type | A1 Journal article | ||
| Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 025013 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | In this experimental study, a flowing dielectric barrier discharge operating at atmospheric pressure is used for the splitting of CO2 into O2 and CO. The influence of the applied frequency and plasma power on the microdischarge properties is investigated to understand their role on the CO2 conversion. Electrical measurements are carried out to explain the conversion trends and to characterize the microdischarges through their number, their lifetime, their intensity and the induced electrical charge. Their influence on the gas and electrode temperatures is also evidenced through optical emission spectroscopy and infrared imaging. It is shown that, in our configuration, the conversion depends mostly on the charge delivered in the plasma and not on the effective plasma voltage when the applied power is modified. Similarly, at constant total current, a better conversion is observed at low frequencies, where a less filamentary discharge regime with a higher effective plasma voltage than that at a higher frequency is obtained. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000372337900015 | Publication Date | 2016-02-25 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 40 | Open Access | |
| Notes | The authors acknowledge financial support from the IAPVII/ 12, P7/34 (Inter-university Attraction Pole) program ‘PSI-Physical Chemistry of Plasma-Surface Interactions’, financially supported by the Belgian Federal Office for Science Policy (BELSPO). A Ozkan would like to thank the financial support given by ‘Fonds David et Alice Van Buuren’. N Britun is a postdoctoral researcher of the F.R.S.-FNRS, Belgium. | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:131904 | Serial  |
4021 | ||
| Permanent link to this record | |||||
| Author | Milovanovic, S.P.; Peeters, F.M. | ||||
| Title | Characterization of the size and position of electron-hole puddles at a graphene p-n junction | Type | A1 Journal article | ||
| Year | 2016 | Publication | Nanotechnology | Abbreviated Journal | Nanotechnology |
| Volume | 27 | Issue | 27 | Pages | 105203 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT) | ||||
| Abstract | The effect of an electron-hole puddle on the electrical transport when governed by snake states in a bipolar graphene structure is investigated. Using numerical simulations we show that information on the size and position of the electron-hole puddle can be obtained using the dependence of the conductance on magnetic field and electron density of the gated region. The presence of the scatterer disrupts snake state transport which alters the conduction pattern. We obtain a simple analytical formula that connects the position of the electron-hole puddle with features observed in the conductance. The size of the electron-hole puddle is estimated from the magnetic field and gate potential that maximizes the effect of the puddle on the electrical transport. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | English | Wos | 000369849200003 | Publication Date | 2016-02-11 |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0957-4484 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.44 | Times cited | 3 | Open Access | |
| Notes | This work was supported by the Flemish Science Foundation (FWO-Vl) and the European Science Foundation (ESF) under the EUROCORES Program EuroGRAPHENE within the project CONGRAN. We acknowledge interesting correspondence with Thiti Taychatanapat. | Approved | Most recent IF: 3.44 | ||
| Call Number | c:irua:131907 | Serial |
4025 | ||
| Permanent link to this record | |||||
| Author | Filez, M.; Redekop, E.A.; Poelman, H.; Galvita, V.V.; Meledina, M.; Turner, S.; Van Tendeloo, G.; Detavernier, C.; Marin, G.B. | ||||
| Title | One-pot synthesis of Pt catalysts based on layered double hydroxides: an application in propane dehydrogenation | Type | A1 Journal article | ||
| Year | 2016 | Publication | Catalysis science & technology | Abbreviated Journal | Catal Sci Technol |
| Volume | 6 | Issue | 6 | Pages | 1863-1869 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Simple methods for producing noble metal catalysts with well-defined active sites and improved performance are highly desired in the chemical industry. However, the development of such methods still presents a formidable synthetic challenge. Here, we demonstrate a one-pot synthesis route for the controlled production of bimetallic Pt–In catalysts based on the single-step formation of Mg,Al,Pt,In-containing layered double hydroxides (LDHs). Besides their simple synthesis, these Pt–In catalysts exhibit superior propane dehydrogenation activity compared to their multi-step synthesized analogs. The presented material serves as a showcase for the one-pot synthesis of a broader class of LDH-derived mono- and multimetallic Pt catalysts. The compositional flexibility provided by LDH materials can pave the way towards highperforming Pt-based catalysts with tunable physicochemical properties. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000372172800031 | Publication Date | 2015-10-23 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2044-4753 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 5.773 | Times cited | 12 | Open Access | |
| Notes | This work was supported by the Fund for Scientific Research Flanders (FWO: G.0209.11), the ‘Long Term Structural Methusalem Funding by the Flemish Government’, the IAP 7/05 Interuniversity Attraction Poles Programme – Belgian State – Belgian Science Policy, and the Fund for Scientific Research Flanders (FWO-Vlaanderen) by supplying financing of beam time at the DUBBLE beamline of the ESRF and travel costs and a post-doctoral fellowship for S. T. The authors acknowledge the assistance from the DUBBLE (XAS campaign 26-01-979) and SuperXAS staff (Proposal 20131191). E. A. Redekop acknowledges the Marie Curie International Incoming Fellowship granted by the European Commission (Grant Agreement No. 301703). The authors also express their gratitude to O. Janssens for performing ex situ XRD characterization. | Approved | Most recent IF: 5.773 | ||
| Call Number | c:irua:133167 | Serial |
4057 | ||
| Permanent link to this record | |||||
| Author | Trenchev, G.; Kolev, S.; Bogaerts, A. | ||||
| Title | A 3D model of a reverse vortex flow gliding arc reactor | Type | A1 Journal article | ||
| Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 035014 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | In this computational study, a gliding arc plasma reactor with a reverse-vortex flow stabilization is modelled for the first time by a fluid plasma description. The plasma reactor operates with argon gas at atmospheric pressure. The gas flow is simulated using the k-ε Reynolds-averaged Navier–Stokes turbulent model. A quasi-neutral fluid plasma model is used for computing the plasma properties. The plasma arc movement in the reactor is observed, and the results for the gas flow, electrical characteristics, plasma density, electron temperature, and gas temperature are analyzed. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000376557400022 | Publication Date | 2016-04-09 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 20 | Open Access | |
| Notes | This research was carried out in the framework of the network on Physical Chemistry of Plasma–Surface Interactions— Interuniversity Attraction Poles, phase VII (http://psi-iap7.ulb. ac.be/), and supported by the Belgian Science Policy Office (BELSPO), and it was also funded by the Fund for Scientific Research Flanders (FWO). Grant number: 11U5316N. | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:132888 c:irua:132888 | Serial |
4063 | ||
| Permanent link to this record | |||||
| Author | Ozkan, A.; Dufour, T.; Bogaerts, A.; Reniers, F. | ||||
| Title | How do the barrier thickness and dielectric material influence the filamentary mode and CO2conversion in a flowing DBD? | Type | A1 Journal article | ||
| Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 045016 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Dielectric barrier discharges (DBDs) are commonly used to generate cold plasmas at atmospheric pressure. Whatever their configuration (tubular or planar), the presence of a dielectric barrier is mandatory to prevent too much charge build up in the plasma and the formation of a thermal arc. In this article, the role of the barrier thickness (2.0, 2.4 and 2.8 mm) and of the kind of dielectric material (alumina, mullite, pyrex, quartz) is investigated on the filamentary behavior in the plasma and on the CO2 conversion in a tubular flowing DBD, by means of mass spectrometry measurements correlated with electrical characterization and IR imaging. Increasing the barrier thickness decreases the capacitance, while preserving the electrical charge. As a result, the voltage over the dielectric increases and a larger number of microdischarges is generated, which enhances the CO2 conversion. Furthermore, changing the dielectric material of the barrier, while keeping the same geometry and dimensions, also affects the CO2 conversion. The highest CO2 conversion and energy efficiency are obtained for quartz and alumina, thus not following the trend of the relative permittivity. From the electrical characterization, we clearly demonstrate that the most important parameters are the somewhat higher effective plasma voltage (yielding a somewhat higher electric field and electron energy in the plasma) for quartz, as well as the higher plasma current (and thus larger electron density) and the larger number of microdischarge filaments (mainly for alumina, but also for quartz). The latter could be correlated to the higher surface roughness for alumina and to the higher voltage over the dielectric for quartz. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000380380200030 | Publication Date | 2016-06-30 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 24 | Open Access | |
| Notes | The authors acknowledge financial support from the IAPVII/ 12, P7/34 (Inter-university Attraction Pole) program ‘PSI-Physical Chemistry of Plasma-Surface Interactions’, financially supported by the Belgian Federal Office for Science Policy (BELSPO). A. Ozkan would like to thank the financial support given by ‘Fonds David et Alice Van Buuren’. | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:134396 | Serial |
4100 | ||
| Permanent link to this record | |||||
| Author | Berthelot, A.; Bogaerts, A. | ||||
| Title | Modeling of plasma-based CO2conversion: lumping of the vibrational levels | Type | A1 Journal article | ||
| Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 045022 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Although CO2 conversion by plasma technology is gaining increasing interest, the underlying mechanisms for an energy-efficient process are still far from understood. In this work, a reduced non-equilibrium CO2 plasma chemistry set, based on level lumping of the vibrational levels, is proposed and the reliability of this level-lumping method is tested by a self-consistent zero-dimensional code. A severe reduction of the number of equations to be solved is achieved, which is crucial to be able to model non-equilibrium CO2 plasmas by 2-dimensional models. Typical conditions of pressure and power used in a microwave plasma for CO2 conversion are investigated. Several different sets, using different numbers of lumped groups, are considered. The lumped models with 1, 2 or 3 groups are able to reproduce the gas temperature, electron density and electron temperature profiles, as calculated by the full model treating all individual excited levels, in the entire pressure range investigated. Furthermore, a 3-groups model is also able to reproduce the shape of the vibrational distribution function (VDF) and gives the most reliable prediction of the CO2 conversion. A strong influence of the vibrational excitation on the plasma characteristics is observed. Finally, the limitations of the lumped-levels method are discussed. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000380380200036 | Publication Date | 2016-07-08 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0963-0252 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 33 | Open Access | |
| Notes | This project has received funding from the European Union’s Seventh Framework Programme for research, technological development and demonstration under grant agreement no 606889 and it was also carried out in the framework of the network on Physical Chemistry of Plasma-Surface Interactions—Interuniversity Attraction Poles, phase VII (PSI-IAP7) supported by the Belgian Science Policy Office (BELSPO). The computational work was carried out using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UA), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UA. | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:134397 | Serial |
4101 | ||
| Permanent link to this record | |||||
| Author | Ozkan, A.; Dufour, T.; Silva, T.; Britun, N.; Snyders, R.; Reniers, F.; Bogaerts, A. | ||||
| Title | DBD in burst mode: solution for more efficient CO2conversion? | Type | A1 Journal article | ||
| Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 055005 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | CO2 conversion into value-added products has gained significant interest over the few last years, as the greenhouse gas concentrations constantly increase due to anthropogenic activities. Here we report on experiments for CO2 conversion by means of a cold atmospheric plasma using a cylindrical flowing dielectric barrier discharge (DBD) reactor. A detailed comparison of this DBD ignited in a so-called burst mode (i.e. where an AC voltage is applied during a limited amount of time) and pure AC mode is carried out to evaluate their effect on the conversion of CO2 as well as on the energy efficiency. Decreasing the duty cycle in the burst mode from 100% (i.e. corresponding to pure AC mode) to 40% leads to a rise in the conversion from 16–26% and to a rise in the energy efficiency from 15 to 23%. Based on a detailed electrical analysis, we show that the conversion correlates with the features of the microfilaments. Moreover, the root-mean-square voltage in the burst mode remains constant as a function of the process time for the duty cycles <70%, while a higher duty cycle or the usual pure AC mode leads to a clear voltage decay by more than 500 V, over approximately 90 s, before reaching a steady state regime. The higher plasma voltage in the burst mode yields a higher electric field. This causes the increasing the electron energy, and therefore their involvement in the CO2 dissociation process, which is an additional explanation for the higher CO2 conversion and energy efficiency in the burst mode. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000403945500005 | Publication Date | 2016-08-02 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 17 | Open Access | |
| Notes | The authors acknowledge financial support from the IAPVII/ 12, P7/34 (Inter-university Attraction Pole) program ‘PSI-Physical Chemistry of Plasma-Surface Interactions’, financially supported by the Belgian Federal Office for Science Policy (BELSPO). A. Ozkan would also like to thank financial support given by ‘Fonds David et Alice Van Buuren’. | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:134841 | Serial |
4107 | ||
| Permanent link to this record | |||||
| Author | Bogaerts, A.; Wang, W.; Berthelot, A.; Guerra, V. | ||||
| Title | Modeling plasma-based CO2conversion: crucial role of the dissociation cross section | Type | A1 Journal article | ||
| Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 055016 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Plasma-based CO2 conversion is gaining increasing interest worldwide. A large research effort is devoted to improving the energy efficiency. For this purpose, it is very important to understand the underlying mechanisms of the CO2 conversion. The latter can be obtained by computer modeling, describing in detail the behavior of the various plasma species and all relevant chemical processes. However, the accuracy of the modeling results critically depends on the accuracy of the assumed input data, like cross sections. This is especially true for the cross section of electron impact dissociation, as the latter process is believed to proceed through electron impact excitation, but it is not clear from the literature which excitation channels effectively lead to dissociation. Therefore, the present paper discusses the effect of different electron impact dissociation cross sections reported in the literature on the calculated CO2 conversion, for a dielectric barrier discharge (DBD) and a microwave (MW) plasma. Comparison is made to experimental data for the DBD case, to elucidate which cross section might be the most realistic. This comparison reveals that the cross sections proposed by Itikawa and by Polak and Slovetsky both seem to underestimate the CO2 conversion. The cross sections recommended by Phelps with thresholds of 7 eV and 10.5 eV yield a CO2 conversion only slightly lower than the experimental data, but the sum of both cross sections overestimates the values, indicating that these cross sections represent dissociation, but most probably also include other (pure excitation) channels. Our calculations indicate that the choice of the electron impact dissociation cross section is crucial for the DBD, where this process is the dominant mechanism for CO2 conversion. In the MW plasma, it is only significant at pressures up to 100 mbar, while it is of minor importance for higher pressures, when dissociation proceeds mainly through collisions of CO2 with heavy particles. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000384030600001 | Publication Date | 2016-08-31 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 57 | Open Access | |
| Notes | The authors would like to thank R Snoeckx and S Heijkers for the interesting discussions. This research was supported by the European Union’s Seventh Framework Programme for research, technological development and demonstration under grant agreement no. 606889, the European Marie Skłodowska-Curie Individual Fellowship project ‘GlidArc’ within Horizon2020, the FWO project (grant G.0383.16N), and the Network on Physical Chemistry of Plasma-Surface Interactions—Interuniversity Attraction Poles, phase VII (PSI-IAP7), supported by the Belgian Science Policy Office (BELSPO). The computational work was carried out using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UA), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UA. VG was partially supported by the Portuguese FCT— Fundação para a Ci | Approved | Most recent IF: 3.302 | ||
| Call Number | c:irua:135070 | Serial |
4111 | ||
| Permanent link to this record | |||||
| Author | Spadaro, M.C.; Luches, P.; Bertoni, G.; Grillo, V.; Turner, S.; Van Tendeloo, G.; Valeri, S.; D'Addato, S. | ||||
| Title | Influence of defect distribution on the reducibility of CeO2-x nanoparticles | Type | A1 Journal article | ||
| Year | 2016 | Publication | Nanotechnology | Abbreviated Journal | Nanotechnology |
| Volume | 27 | Issue | 27 | Pages | 425705 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Ceria nanoparticles (NPs) are fundamental in heterogeneous catalysis because of their ability to store or release oxygen depending on the ambient conditions. Their oxygen storage capacity is strictly related to the exposed planes, crystallinity, density and distribution of defects. In this work a study of ceria NPs produced with a ligand-free, physical synthesis method is presented. The NP films were grown by a magnetron sputtering based gas aggregation source and studied by high resolution- and scanning-transmission electron microscopy and x-ray photoelectron spectroscopy. In particular, the influence of the oxidation procedure on the NP reducibility has been investigated. The different reducibility has been correlated to the exposed planes, crystallinity and density and distribution of structural defects. The results obtained in this work represent a basis to obtain cerium oxide NP with desired oxygen transport properties. | ||||
| Address | Dipartimento FIM, Universita di Modena e Reggio Emilia, via G. Campi 213/a, I-41125 Modena, Italy. CNR-NANO, via G. Campi 213/a, I-41125 Modena, Italy | ||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | English | Wos | 000385483900004 | Publication Date | 2016-09-15 |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0957-4484 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.44 | Times cited | 11 | Open Access | |
| Notes | The authors gratefully acknowledge financial support by the Italian MIUR under grant FIRB RBAP115AYN (Oxides at the nanoscale: multifunctionality and applications). The activity is performed within the COST Action CM1104 'Reducible oxide chemistry, structure and functions'. The research leading to these results has received funding also from the European Union Seventh Framework Programme under Grant Agreement 312483—ESTEEM2 (Integrated Infrastructure Initiative–I3).; esteem2_ta | Approved | Most recent IF: 3.44 | ||
| Call Number | EMAT @ emat @ c:irua:135424 | Serial |
4130 | ||
| Permanent link to this record | |||||
| Author | Cai, H.; Kang, J.; Sahin, H.; Chen, B.; Suslu, A.; Wu, K.; Peeters, F.; Meng, X.; Tongay, S. | ||||
| Title | Exciton pumping across type-I gallium chalcogenide heterojunctions | Type | A1 Journal article | ||
| Year | 2016 | Publication | Nanotechnology | Abbreviated Journal | Nanotechnology |
| Volume | 27 | Issue | 27 | Pages | 065203 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT) | ||||
| Abstract | Quasi-two-dimensional gallium chalcogenide heterostructures are created by transferring exfoliated few-layer GaSe onto bulk GaTe sheets. Luminescence spectroscopy measurements reveal that the light emission from underlying GaTe layers drastically increases on heterojunction regions where GaSe layers make contact with the GaTe. Density functional theory (DFT) and band offset calculations show that conduction band minimum (CBM) (valance band maximum (VBM)) values of GaSe are higher (lower) in energy compared to GaTe, forming type-I band alignment at the interface. Consequently, GaSe layers provide photo-excited electrons and holes to GaTe sheets through relatively large built-in potential at the interface, increasing overall exciton population and light emission from GaTe. Observed results are not specific to the GaSe/GaTe system but observed on GaS/GaSe heterolayers with type-I band alignment. Observed experimental findings and theoretical studies provide unique insights into interface effects across dissimilar gallium chalcogenides and offer new ways to boost optical performance by simple epitaxial coating. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Bristol | Editor | ||
| Language | Wos | 000368897100008 | Publication Date | 2016-01-13 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0957-4484 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.44 | Times cited | 15 | Open Access | |
| Notes | ; This work was supported by the Arizona State University seeding program, the Flemish Science Foundation (FWO-Vl) and the Methusalem foundation of the Flemish government. HS is supported by a FWO Pegasus Long Marie Curie Fellowship. JK is supported by a FWO Pegasus-short Marie Curie Fellowship. We acknowledge the use of the John M Cowley Center for High Resolution Electron Microscopy at Arizona State University. The authors thank Anupum Pant for useful discussions. We gratefully acknowledge the use of the facilities at the LeRoy Eyring Center for Solid State Science at Arizona State University. S Tongay acknowledges support from DMR-1552220. ; | Approved | Most recent IF: 3.44 | ||
| Call Number | UA @ lucian @ c:irua:131570 | Serial |
4179 | ||
| Permanent link to this record | |||||
| Author | Forsh, E.A.; Abakumov, A.M.; Zaytsev, V.B.; Konstantinova, E.A.; Forsh, P.A.; Rumyantseva, M.N.; Gaskov, A.M.; Kashkarov, P.K. | ||||
| Title | Optical and photoelectrical properties of nanocrystalline indium oxide with small grains | Type | A1 Journal article | ||
| Year | 2015 | Publication | Thin solid films : an international journal on the science and technology of thin and thick films | Abbreviated Journal | Thin Solid Films |
| Volume | 595 | Issue | 595 | Pages | 25-31 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Optical properties, spectral dependence of photoconductivity and photoconductivity decay in nanocrystalline indium oxide In2O3 are studied. A number of nanostructured In2O3 samples with various nanocrystals size are prepared by sol-gel method and characterized using various techniques. The mean nanocrystals size varies from 7 to 8 nm to 39-41 nm depending on the preparation conditions. Structural characterization of the In2O3 samples is performed by means of transmission electron microscopy and X-ray powder diffraction. The combined analysis of ultraviolet-visible absorption spectroscopy and diffuse reflectance spectroscopy shows that nanostructuring leads to the change in optical band gap: optical band gap of the In2O3 samples (with an average nanocrystal size from 7 to 41 nm) is equal to 2.8 eV. We find out the correlation between spectral dependence of photoconductivity and optical properties of nanocrystalline In2O3: sharp increase in photoconductivity was observed to begin at 2.8 eV that is equal to the optical bandgap in the In2O3 samples, and reached its maximum at 3.2-3.3 eV. The combined analysis of the slow photoconductivity decay in air, vacuum and argon, that was accurately fitted by a stretched-exponential function, and electron paramagnetic resonance (EPR) measurements shows that the kinetics of photoconductivity decay is strongly depended on the presence of oxygen molecules in the ambient of In2O3 nanocrystals. There is the quantitative correlation between EPR and photoconductivity data. Based on the obtained data we propose the model clearing up the phenomenon of permanent photoconductivity decay in nanocrystalline In2O3. (C) 2015 Elsevier B.V. All rights reserved. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Lausanne | Editor | ||
| Language | Wos | 000365812400005 | Publication Date | 2015-10-27 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0040-6090 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 1.879 | Times cited | 18 | Open Access | |
| Notes | Approved | Most recent IF: 1.879; 2015 IF: 1.759 | |||
| Call Number | UA @ lucian @ c:irua:130254 | Serial |
4219 | ||
| Permanent link to this record | |||||
| Author | Oueslati, S.; Brammertz, G.; Buffiere, M.; ElAnzeery, H.; Touayar, O.; Koeble, C.; Bekaert, J.; Meuris, M.; Poortmans, J. | ||||
| Title | Physical and electrical characterization of high-performance Cu2ZnSnSe4 based thin film solar cells | Type | A1 Journal article | ||
| Year | 2015 | Publication | Thin solid films : an international journal on the science and technology of thin and thick films | Abbreviated Journal | Thin Solid Films |
| Volume | 582 | Issue | 582 | Pages | 224-228 |
| Keywords | A1 Journal article; Condensed Matter Theory (CMT) | ||||
| Abstract | We report on the electrical, optical and physical properties of Cu2ZnSnSe4 solar cells using an absorber layer fabricated by selenization of sputtered Cu, Zn and Cu10Sn90 multilayers. A maximum active-area conversion efficiency of 10.4% under AM1.5G was measured with a maximum short circuit current density of 39.7 mA/cm(2), an open circuit voltage of 394 mV and a fill factor of 66.4%. We perform electrical and optical characterization using photoluminescence spectroscopy, external quantum efficiency, current-voltage and admittance versus temperature measurements in order to derive information about possible causes for the low open circuit voltage values observed. The main defects derived from these measurements are strong potential fluctuations in the absorber layer as well as a potential barrier of the order of 133 meV at the back side contact. (C) 2014 Elsevier B.V. All rights reserved. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Lausanne | Editor | ||
| Language | Wos | 000352225900048 | Publication Date | 2014-10-20 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0040-6090 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 1.879 | Times cited | 49 | Open Access | |
| Notes | ; We would like to acknowledge Tom De Geyter, Greetje Godiers, and Guido Huyberechts from Flamac in Gent for sputtering of the metal layers. AGC is acknowledged for providing substrates. This research is partially funded by the Flemish government, Department Economy, Science and Innovation. ; | Approved | Most recent IF: 1.879; 2015 IF: 1.759 | ||
| Call Number | UA @ lucian @ c:irua:132504 | Serial |
4225 | ||
| Permanent link to this record | |||||
| Author | Wang, W.; Bogaerts, A. | ||||
| Title | Effective ionisation coefficients and critical breakdown electric field of CO2at elevated temperature: effect of excited states and ion kinetics | Type | A1 Journal article | ||
| Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 055025 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Electrical breakdown by the application of an electric field occurs more easily in hot gases than in cold gases because of the extra electron-species interactions that occur as a result of dissociation, ionization and excitation at higher temperature. This paper discusses some overlooked physics and clarifies inaccuracies in the evaluation of the effective ionization coefficients and the critical reduced breakdown electric field of CO2 at elevated temperature, considering the influence of excited states and ion kinetics. The critical reduced breakdown electric field is obtained by balancing electron generation and loss mechanisms using the electron energy distribution function (EEDF) derived from the Boltzmann transport equation under the two-term approximation. The equilibrium compositions of the hot gas mixtures are determined based on Gibbs free energy minimization considering the ground states as well as vibrationally and electronically excited states as independent species, which follow a Boltzmann distribution with a fixed excitation temperature. The interaction cross sections between electrons and the excited species, not reported previously, are properly taken into account. Furthermore, the ion kinetics, including electron–ion recombination, associative electron detachment, charge transfer and ion conversion into stable negative ion clusters, are also considered. Our results indicate that the excited species lead to a greater population of high-energy electrons at higher gas temperature and this affects the Townsend rate coefficients (i.e. of electron impact ionization and attachment), but the critical reduced breakdown electric field strength of CO2 is only affected when also properly accounting for the ion kinetics. Indeed, the latter greatly influences the effective ionization coefficients and hence the critical reduced breakdown electric field at temperatures above 1500 K. The rapid increase of the dissociative electron attachment cross-section of molecular oxygen with rising vibrational quantum number leads to a larger electron loss rate and this enhances the critical reduced breakdown electric field strength in the temperature range where the concentration of molecular oxygen is relatively high. The results obtained in this work show reasonable agreement with experimental results from literature, and are important for the evaluation of the dielectric strength of CO2 in a highly reactive environment at elevated temperature. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000385494000006 | Publication Date | 2016-09-22 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 3 | Open Access | |
| Notes | Skłodowska-Curie Individual Fellowship ‘GlidArc’ within Horizon2020 (Grant No.657304) and the FWO project (grant G.0383.16N). The computational work was carried out using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UA), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UA. | Approved | Most recent IF: 3.302 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:135515 | Serial |
4281 | ||
| Permanent link to this record | |||||
| Author | Wang, W.; Berthelot, A.; Kolev, S.; Tu, X.; Bogaerts, A. | ||||
| Title | CO2 conversion in a gliding arc plasma: 1D cylindrical discharge model | Type | A1 Journal article | ||
| Year | 2016 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 25 | Issue | 25 | Pages | 065012 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | CO 2 conversion by a gliding arc plasma is gaining increasing interest, but the underlying mechanisms for an energy-efficient process are still far from understood. Indeed, the chemical complexity of the non-equilibrium plasma poses a challenge for plasma modeling due to the huge computational load. In this paper, a one-dimensional (1D) gliding arc model is developed in a cylindrical frame, with a detailed non-equilibrium CO 2 plasma chemistry set, including the CO 2 vibrational kinetics up to the dissociation limit. The model solves a set of time- dependent continuity equations based on the chemical reactions, as well as the electron energy balance equation, and it assumes quasi-neutrality in the plasma. The loss of plasma species and heat due to convection by the transverse gas flow is accounted for by using a characteristic frequency of convective cooling, which depends on the gliding arc radius, the relative velocity of the gas flow with respect to the arc and on the arc elongation rate. The calculated values for plasma density and plasma temperature within this work are comparable with experimental data on gliding arc plasma reactors in the literature. Our calculation results indicate that excitation to the vibrational levels promotes efficient dissociation in the gliding arc, and this is consistent with experimental investigations of the gliding arc based CO 2 conversion in the literature. Additionally, the dissociation of CO 2 through collisions with O atoms has the largest contribution to CO 2 splitting under the conditions studied. In addition to the above results, we also demonstrate that lumping the CO 2 vibrational states can bring a significant reduction of the computational load. The latter opens up the way for 2D or 3D models with an accurate description of the CO 2 vibrational kinetics. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000386605100002 | Publication Date | 2016-10-18 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 3 | Open Access | |
| Notes | This research was supported by the European Marie Skłodowska-Curie Individual Fellowship ‘GlidArc’ within Horizon2020 (Grant No. 657304) and by the FWO project (grant G.0383.16N). The calculations were performed using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UAntwerpen), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UAntwerpen. | Approved | Most recent IF: 3.302 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:135990 | Serial |
4286 | ||
| Permanent link to this record | |||||
| Author | Meledin, A.; Turner, S.; Cayado, P.; Mundet, B.; Solano, E.; Ricart, S.; Ros, J.; Puig, T.; Obradors, X.; Van Tendeloo, G. | ||||
| Title | Unique nanostructural features in Fe, Mn-doped YBCO thin films | Type | A1 Journal article | ||
| Year | 2016 | Publication | Superconductor science and technology | Abbreviated Journal | Supercond Sci Tech |
| Volume | 29 | Issue | 29 | Pages | 125009 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | An attempt to grow a thin epitaxial composite film of YBa2Cu3O7−δ (YBCO) with spinel MnFe2O4 (MFO) nanoparticles on a LAO substrate using the CSD approach resulted in a decomposition of the spinel and various doping modes of YBCO with the Fe and Mn cations. These nanostructural effects lead to a lowering of T c and a slight J c increase in field. Using a combination of advanced transmission electron microscopy (TEM) techniques such as atomic resolution high-angle annular dark field scanning TEM, energy dispersive x-ray spectroscopy and electron energy-loss spectroscopy we have been able to decipher and characterize the effects of the Fe and Mn doping on the film architecture. The YBaCuFeO5 anion-deficient double perovskite phase was detected in the form of 3D inclusions as well as epitaxially grown lamellas within the YBCO matrix. These nano-inclusions play a positive role as pinning centers responsible for the J c/J sf (H) dependency smoothening at high magnetic fields in the YBCO-MFO films with respect to the pristine YBCO films. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000387680100001 | Publication Date | 2016-10-31 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0953-2048 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 2.878 | Times cited | 6 | Open Access | |
| Notes | The authors gratefully acknowledge Prof. Dr. A. Abakumov and Dr. J. Gazquez for discussions and corrections. Part of this work was performed within the framework of the EUROTAPES project (FP7-NMP.2011.2.2-1 Grant no. 280432), funded by the European Union. ICMAB research was financed by the Ministry of Economy and Competitiveness, and FEDER funds under the projects MAT2011-28874-C02-01, MAT2014-51778-C2-1-R, ENE2014-56109-C3-3-R and Consolider Nanoselect CSD2007-00041, and by Generalitat de Catalunya (2009 SGR 770, 2015 SGR 753 and Xarmae). ICMAB acknowledges support from Severo Ochoa Program (MINECO, Grant SEV-2015-0496). | Approved | Most recent IF: 2.878 | ||
| Call Number | EMAT @ emat @ c:irua:136444 | Serial |
4295 | ||
| Permanent link to this record | |||||
| Author | Chizhov, A.S.; Rumyantseva, M.N.; Vasiliev, R.B.; Filatova, D.G.; Drozdov, K.A.; Krylov, I.V.; Marchevsky, A.V.; Karakulina, O.M.; Abakumov, A.M.; Gaskov, A.M. | ||||
| Title | Visible light activation of room temperature NO2 gas sensors based on ZnO, SnO2 and In2O3 sensitized with CdSe quantum dots | Type | A1 Journal article | ||
| Year | 2016 | Publication | Thin solid films : an international journal on the science and technology of thin and thick films | Abbreviated Journal | Thin Solid Films |
| Volume | 618 | Issue | 618 | Pages | 253-262 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | This work reports the analysis of visible light activation of room temperature NO2 gas sensitivity of metal oxide semiconductors (MOS): blank and CdSe quantum dots (QDs) sensitized nanocrystallinematrixes ZnO, SnO2 and In2O3. Nanocrystalline metal oxides (MOx) ZnO, SnO2, In2O3 were synthesized by the precipitation method. Colloidal CdSe QDs were obtained by high temperature colloidal synthesis. Sensitization was effectuated by direct adsorption of CdSe QDs stabilized with oleic acid on MOx surface. The role of illumination consists in generation of electrons, which can be transferred into MOx conduction band, and holes that can recombine with the electrons previously trapped by the chemisorbed acceptor species and thus activate desorption of analyte molecules. Under green light illumination for blank SnO2 and In2O3 matrixes the indirect consequential mechanism for the generation of holes is proposed. Anothermechanismis realized in the presence of CdSe QDs. In this case the electron-hole pair is generated in the CdSe quantum dot. Sensor measurements demonstrated that synthesizedmaterials can be used for NO2 detection under visible (green) light illumination at room temperature without any thermal heating. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000389164400005 | Publication Date | 2016-09-18 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0040-6090 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 1.879 | Times cited | 19 | Open Access | |
| Notes | The work was financially supported by Russian Foundation for Basic Research grant no. 15-03-03026. | Approved | Most recent IF: 1.879 | ||
| Call Number | EMAT @ emat @ c:irua:138598 | Serial |
4321 | ||
| Permanent link to this record | |||||
| Author | Jacobs, W.; Reynaerts, C.; Andries, S.; van den Akker, S.; Moonen, N.; Lamoen, D. | ||||
| Title | Analyzing the dispersion of cargo vapors around a ship’s superstructure by means of wind tunnel experiments | Type | A1 Journal article | ||
| Year | 2016 | Publication | Journal of marine science and technology | Abbreviated Journal | J Mar Sci Tech-Japan |
| Volume | 21 | Issue | 21 | Pages | 758-766 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | In a previous study, it was found that cargo tank operations like cleaning and venting, lead to higher cargo vapor concentrations around the ship’s superstructure. Can wind tunnel experiments confirm these findings? Is there an improvement when using higher outlets at high velocities compared to lower outlets with a low outlet velocity? Is there a relation between relative wind speed and measured concentration? These questions were investigated in the Peutz wind tunnel. By using a tracer gas for the wind tunnel experiments, concentration coefficients have been calculated for various settings. The study shows that using high-velocity outlets is an efficient way to keep concentrations as low as possible. The only exception is for relative wind directions from the bow. In this last case using a manhole as ventilation outlet leads to lower concentrations. With increasing wind speeds the building downwash effect resulted in higher concentration coefficients near the main deck. This study confirms our on-board measurements and suggests the lowering of the ventilation inlet of the accommodation, so that the high-velocity outlet can be used safely at all times. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000388260200015 | Publication Date | 2016-05-21 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0948-4280 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 0.838 | Times cited | 2 | Open Access | |
| Notes | The authors would like to thank Peutz bv. at Molenhoek, the Netherlands, for providing the wind tunnel facilities and their assistance during the various stages of this research. | Approved | Most recent IF: 0.838 | ||
| Call Number | EMAT @ emat @ c:irua:138728 | Serial |
4326 | ||
| Permanent link to this record | |||||
| Author | Van Aelst, J.; Philippaerts, A.; Bartholomeeusen, E.; Fayad, E.; Thibault-Starzyk, F.; Lu, J.; Schryvers, D.; Ooms, R.; Verboekend, D.; Jacobs, P.; Sels, B. | ||||
| Title | Towards biolubricant compatible vegetable oils by pore mouth hydrogenation with shape-selective Pt/ZSM-5 catalysts | Type | A1 Journal article | ||
| Year | 2016 | Publication | Catalysis science & technology | Abbreviated Journal | Catal Sci Technol |
| Volume | 6 | Issue | 6 | Pages | 2820-2828 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Pt/ZSM-5 catalysts with various crystal sizes were prepared via competitive ion-exchange, followed by a slow activation procedure. Even when using very large ZSM-5 crystals, highly dispersed Pt nano-clusters were contained within the zeolite crystal's voids, as ascertained by 2D pressure-jump IR spectroscopy of adsorbed CO and focussed ion-beam transmission electron microscopy. The shape-selective properties of the Pt/ZSM-5 catalysts were evaluated in the partial hydrogenation of soybean oil. Unique hydrogenation selectivities were observed, as the fatty acids located at the central position of the triacylglycerol (TAG) molecules were preferentially hydrogenated. The resulting oil has therefore high levels of intermediately melting TAGs, which are compatible with biolubricants due to their improved oxidative stability and still appropriate low-temperature fluidity. The TAG distribution in the partially hydrogenated soybean oil samples was independent from the zeolite crystal size, while the hydrogenation activity linearly increases with the crystal's external surface area. This trend was confirmed with a Pt loaded mesoporous ZSM-5 zeolite, obtained via a mild alkaline treatment. These observations imply and confirm a genuine pore mouth catalysis mechanism, in which only one fatty acid chain of the TAG is able to enter the micropores of ZSM-5, where the double bonds are hydrogenated by the crystal encapsulated Pt-clusters. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000374790200031 | Publication Date | 2016-03-31 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2044-4753 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 5.773 | Times cited | 5 | Open Access | |
| Notes | The research was funded through a PhD grant to J. V. A. of the Agency for Innovation by Science and Technology in Flanders (IWT). A. P. and D. V. acknowledge the F. W. O.-Vlaanderen (Research Foundation Flanders) for a post-doctoral fellowship. E. B. was kindly funded by an F. W. O.-Vlaanderen project. This work was performed in the framework of an Associated International Laboratory between FWO and CNRS. | Approved | Most recent IF: 5.773 | ||
| Call Number | EMAT @ emat @ c:irua:138981 | Serial |
4335 | ||
| Permanent link to this record | |||||
| Author | Sun, S.R.; Kolev, S.; Wang, H.X.; Bogaerts, A. | ||||
| Title | Coupled gas flow-plasma model for a gliding arc: investigations of the back-breakdown phenomenon and its effect on the gliding arc characteristics | Type | A1 Journal article | ||
| Year | 2017 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 26 | Issue | 26 | Pages | 015003 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | We present a 3D and 2D Cartesian quasi-neutral plasma model for a low current argon gliding arc discharge, including strong interactions between the gas flow and arc plasma column. The 3D model is applied only for a short time of 0.2 ms due to its huge computational cost. It mainly serves to verify the reliability of the 2D model. As the results in 2D compare well with those in 3D, they can be used for a better understanding of the gliding arc basic characteristics. More specifically, we investigate the back-breakdown phenomenon induced by an artificially controlled plasma channel, and we discuss its effect on the gliding arc characteristics. The back-breakdown phenomenon, or backward-jump motion of the arc, as observed in the experiments, results in a drop of the gas temperature, as well as in a delay of the arc velocity with respect to the gas flow velocity, allowing more gas to pass through the arc, and thus increasing the efficiency of the gliding arc for gas treatment applications. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000419253000001 | Publication Date | 2016-11-22 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 9 | Open Access | OpenAccess |
| Notes | This work is financially supported by the Methusalem financing, by the Fund for Scientific Research Flanders (FWO) and by the IAP/7 (Inter-university Attraction Pole) program ‘Physical Chemistry of Plasma-Surface Interactions’ from the Belgian Federal Office for Science Policy (BELSPO). The work was carried out in part using the Turing HPC infrastructure of the CalcUA core facility of the Universiteit Antwerpen, a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the Universiteit Antwerpen. This work was also supported by the National Natural Science Foundation of China (Grant Nos. 11275021, 11575019). S R Sun thanks the financial support from the China Scholarship Council. | Approved | Most recent IF: 3.302 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:138993 | Serial |
4337 | ||
| Permanent link to this record | |||||
| Author | Kiymaz, D.; Yagmurcukardes, M.; Tomak, A.; Sahin, H.; Senger, R.T.; Peeters, F.M.; Zareie, H.M.; Zafer, C. | ||||
| Title | Controlled growth mechanism of poly (3-hexylthiophene) nanowires | Type | A1 Journal article | ||
| Year | 2016 | Publication | Nanotechnology | Abbreviated Journal | Nanotechnology |
| Volume | 27 | Issue | 27 | Pages | 455604 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT) | ||||
| Abstract | Synthesis of 1D-polymer nanowires by a self-assembly method using marginal solvents is an attractive technique. While the formation mechanism is poorly understood, this method is essential in order to control the growth of nanowires. Here we visualized the time-dependent assembly of poly (3-hexyl-thiophene-2,5-diyl) (P3HT) nanowires by atomic force microscopy and scanning tunneling microscopy. The assembly of P3HT nanowires was carried out at room temperature by mixing cyclohexanone (CHN), as a poor solvent, with polymer solution in 1,2-dichlorobenzene (DCB). Both pi-pi stacking and planarization, obtained at the mix volume ratio of P3HT (in DCB):CHN (10:7), were considered during the investigation. We find that the length of nanowires was determined by the ordering of polymers in the polymer repetition direction. Additionally, our density functional theory calculations revealed that the presence of DCB and CHN molecules that stabilize the structural distortions due to tail group of polymers was essential for the core-wire formation. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Bristol | Editor | ||
| Language | Wos | 000386132600003 | Publication Date | 2016-10-11 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0957-4484 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.44 | Times cited | 24 | Open Access | |
| Notes | ; This work was supported by the Flemish Science Foundation (FWO-Vl) and the Methusalem foundation of the Flemish government. Computational resources were provided by TUBITAK ULAKBIM, the High Performance and Grid Computing Center (TR-Grid e-Infrastructure), and the HPC infrastructure of the University of Antwerp (CalcUA), a division of the Flemish Supercomputer Center (VSC), which is funded by the Hercules Foundation. HS is supported by a FWO Pegasus-Long Marie Curie Fellowship. HS and RTS acknowledge support from TUBITAK through Project No. 114F397. Also, DA is supported by the Scientific Research Project Fund of Ege University (Project Nr: 12GEE011). ; | Approved | Most recent IF: 3.44 | ||
| Call Number | UA @ lucian @ c:irua:138159 | Serial |
4350 | ||
| Permanent link to this record | |||||
| Author | Tomak, A.; Bacaksiz, C.; Mendirek, G.; Sahin, H.; Hur, D.; Gorgun, K.; Senger, R.T.; Birer, O.; Peeters, F.M.; Zareie, H.M. | ||||
| Title | Structural changes in a Schiff base molecular assembly initiated by scanning tunneling microscopy tip | Type | A1 Journal article | ||
| Year | 2016 | Publication | Nanotechnology | Abbreviated Journal | Nanotechnology |
| Volume | 27 | Issue | 27 | Pages | 335601 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT) | ||||
| Abstract | We report the controlled self-organization and switching of newly designed Schiff base (E)-4-((4-(phenylethynyl) benzylidene) amino) benzenethiol (EPBB) molecules on a Au (111) surface at room temperature. Scanning tunneling microscopy and spectroscopy (STM/STS) were used to image and analyze the conformational changes of the EPBB molecules. The conformational change of the molecules was induced by using the STM tip while increasing the tunneling current. The switching of a domain or island of molecules was shown to be induced by the STM tip during scanning. Unambiguous fingerprints of the switching mechanism were observed via STM/STS measurements. Surface-enhanced Raman scattering was employed, to control and identify quantitatively the switching mechanism of molecules in a monolayer. Density functional theory calculations were also performed in order to understand the microscopic details of the switching mechanism. These calculations revealed that the molecular switching behavior stemmed from the strong interaction of the EPBB molecules with the STM tip. Our approach to controlling intermolecular mechanics provides a path towards the bottom-up assembly of more sophisticated molecular machines. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Bristol | Editor | ||
| Language | Wos | 000383780500012 | Publication Date | 2016-07-05 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0957-4484 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.44 | Times cited | 2 | Open Access | |
| Notes | ; The authors acknowledge financial support from TUBITAK (PROJECT NO: 112T507). This work was also supported by the Flemish Science Foundation (FWO-Vl). Computational resources were provided by TUBITAK ULAKBIM, High Performance and Grid Computing Center (TR-Grid-Infrastructure). HS is supported by an FWO Pegasus Long Marie Curie Fellowship. ; | Approved | Most recent IF: 3.44 | ||
| Call Number | UA @ lucian @ c:irua:137155 | Serial |
4363 | ||
| Permanent link to this record | |||||
| Author | Van Havenbergh, K.; Turner, S.; Marx, N.; Van Tendeloo, G. | ||||
| Title | The mechanical behavior during (de)lithiation of coated silicon nanoparticles as anode material for lithium-ion batteries studied by InSitu transmission electron microscopy | Type | A1 Journal article | ||
| Year | 2016 | Publication | Energy technology | Abbreviated Journal | Energy Technol-Ger |
| Volume | 4 | Issue | 4 | Pages | 1005-1012 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
| Abstract | One approach to cope with the continuous irreversible capacity loss in Si-based electrodes, attributed to lithiation-induced volume changes and the formation of a solid-electrolyte interface (SEI), is by coating silicon nanoparticles. A coating can improve the conductivity of the electrode, form a chemical shield against the electrolyte, or provide mechanical confinement to reduce the volume increase. The influence of such a coating on the mechanical behavior of silicon nanoparticles during Li insertion and Li extraction was investigated by insitu transmission electron microscopy. The type of coating was shown to influence the size of the unreacted core that remains after reaction of silicon with lithium. Furthermore, two mechanisms to relieve the stress generated during volume expansion are reported: the initiation of cracks and the formation of nanovoids. Both result in a full reaction of the silicon nanoparticles, whereas with the formation of cracks, additional surface area is created, on which an SEI can be formed. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000382549500012 | Publication Date | 2016-06-29 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2194-4296; 2194-4288 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 2.789 | Times cited | 6 | Open Access | |
| Notes | Approved | Most recent IF: NA | |||
| Call Number | UA @ lucian @ c:irua:137167 | Serial |
4406 | ||
| Permanent link to this record | |||||
| Author | Heyne, M.H.; de Marneffe, J.-F.; Delabie, A.; Caymax, M.; Neyts, E.C.; Radu, I.; Huyghebaert, C.; De Gendt, S. | ||||
| Title | Two-dimensional WS2 nanoribbon deposition by conversion of pre-patterned amorphous silicon | Type | A1 Journal article | ||
| Year | 2017 | Publication | Nanotechnology | Abbreviated Journal | Nanotechnology |
| Volume | 28 | Issue | 28 | Pages | 04LT01 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | We present a method for area selective deposition of 2D WS2 nanoribbons with tunable thickness on a dielectric substrate. The process is based on a complete conversion of a prepatterned, H-terminated Si layer to metallic W by WF6, followed by in situ sulfidation by H2S. The reaction process, performed at 450 degrees C, yields nanoribbons with lateral dimension down to 20 nm and with random basal plane orientation. The thickness of the nanoribbons is accurately controlled by the thickness of the pre-deposited Si layer. Upon rapid thermal annealing at 900 degrees C under inert gas, the WS2 basal planes align parallel to the substrate. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Bristol | Editor | ||
| Language | Wos | 000391445100001 | Publication Date | 2016-12-15 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0957-4484 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.44 | Times cited | 13 | Open Access | OpenAccess |
| Notes | Approved | Most recent IF: 3.44 | |||
| Call Number | UA @ lucian @ c:irua:140382 | Serial |
4471 | ||
| Permanent link to this record | |||||
| Author | Van Aert, S.; den Dekker, A.J.; van den Bos, A.; Van Dyck, D. | ||||
| Title | High resolution electron microscopy from imaging towards measuring | Type | H2 Book chapter | ||
| Year | 2001 | Publication | ... IEEE International Instrumentation and Measurement Technology Conference T2 – Rediscovering measurement in the age of informatics : proceedings of the 18th IEEE Instrumentation and Measurement Technology Conference (IMTC), 2001: vol 3 | Abbreviated Journal | |
| Volume | Issue | Pages | 2081-2086 | ||
| Keywords | H2 Book chapter; Electron microscopy for materials research (EMAT); Vision lab | ||||
| Abstract | |||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Ieee | Place of Publication | Editor | ||
| Language | Wos | Publication Date | 2002-11-13 | ||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | ISBN | 0-7803-6646-8 | Additional Links | UA library record | |
| Impact Factor | Times cited | Open Access | |||
| Notes | Approved | Most recent IF: NA | |||
| Call Number | UA @ lucian @ c:irua:136870 | Serial |
4501 | ||
| Permanent link to this record | |||||
| Author | Woo, S.Y.; Gauquelin, N.; Nguyen, H.P.T.; Mi, Z.; Botton, G.A. | ||||
| Title | Interplay of strain and indium incorporation in InGaN/GaN dot-in-a-wire nanostructures by scanning transmission electron microscopy | Type | A1 Journal article | ||
| Year | 2015 | Publication | Nanotechnology | Abbreviated Journal | Nanotechnology |
| Volume | 26 | Issue | 26 | Pages | 344002 |
| Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
| Abstract | The interplay between strain and composition is at the basis of heterostructure design to engineer new properties. The influence of the strain distribution on the incorporation of indium during the formation of multiple InGaN/GaN quantum dots (QDs) in nanowire (NW) heterostructures has been investigated, using the combined techniques of geometric phase analysis of atomic-resolution images and quantitative elemental mapping from core-loss electron energy-loss spectroscopy within scanning transmission electron microscopy. The variation in In-content between successive QDs within individual NWs shows a dependence on the magnitude of compressive strain along the growth direction within the underlying GaN barrier layer, which affects the incorporation of In-atoms to minimize the local effective strain energy. Observations suggest that the interfacial misfit between InGaN/GaN within the embedded QDs is mitigated by strain partitioning into both materials, and results in normal stresses inflicted by the presence of the surrounding GaN shell. These experimental measurements are linked to the local piezoelectric polarization fields for individual QDs, and are discussed in terms of the photoluminescence from an ensemble of NWs. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Bristol | Editor | ||
| Language | Wos | 000359079500003 | Publication Date | 2015-08-03 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0957-4484 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.44 | Times cited | 19 | Open Access | |
| Notes | Approved | Most recent IF: 3.44; 2015 IF: 3.821 | |||
| Call Number | UA @ lucian @ c:irua:136278 | Serial |
4504 | ||
| Permanent link to this record | |||||
| Author | Denneulin, T.; Rouvière, J.L.; Béché, A.; Py, M.; Barnes, J.P.; Rochat, N.; Hartmann, J.M.; Cooper, D. | ||||
| Title | The reduction of the substitutional C content in annealed Si/SiGeC superlattices studied by dark-field electron holography | Type | A1 Journal article | ||
| Year | 2011 | Publication | Semiconductor science and technology | Abbreviated Journal | Semicond Sci Tech |
| Volume | 26 | Issue | 12 | Pages | 1-10 |
| Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
| Abstract | Si/Si(1 − x − y)GexCy superlattices are used in the construction of new microelectronic architectures such as multichannel transistors. The introduction of carbon in SiGe allows for compensation of the strain and to avoid plastic relaxation. However, the formation of incoherent β-SiC clusters during annealing limits the processability of SiGeC. This precipitation leads to a modification of the strain in the alloy due to the reduction of the substitutional carbon content. Here, we investigated the strain in annealed Si/Si0.744Ge0.244C0.012 superlattices grown by reduced pressure chemical vapour deposition using dark-field electron holography. The variation of the substitutional C content was calculated by correlating the results with finite-element simulations. The obtained values were then compared with Fourier-transformed infrared spectrometry measurements. It was shown that after annealing for 2 min at 1050 °C carbon no longer has any influence on strain in the superlattice, which behaves like pure SiGe. However, a significant proportion of substitutional C atoms remain in a third-nearest neighbour (3nn) configuration. It was deduced that the influence of 3nn C on strain is negligible and that only isolated atoms have a significant contribution. It was also proposed that the 3nn configuration is an intermediary step during the formation of SiC clusters. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | London | Editor | ||
| Language | Wos | 000300151300010 | Publication Date | 2011-11-07 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 0268-1242 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 2.305 | Times cited | Open Access | ||
| Notes | Approved | Most recent IF: 2.305; 2011 IF: 1.723 | |||
| Call Number | UA @ lucian @ c:irua:136427 | Serial |
4508 | ||
| Permanent link to this record | |||||
| Author | Bergwerf, I.; de Vocht, N.; Tambuyzer, B.; Verschueren, J.; Reekmans, K.; Daans, J.; Ibrahimi, A.; Van Tendeloo, V.; Chatterjee, S.; Goossens, H.; Jorens, P.G.; Baekelandt, V.; Ysebaert, D.; Van Marck, E.; Berneman, Z.N.; Van Der Linden, A.; Ponsaerts, P. | ||||
| Title | Reporter gene-expressing bone marrow-derived stromal cells are immune-tolerated following implantation in the central nervous system of syngeneic immunocompetent mice | Type | A1 Journal article | ||
| Year | 2009 | Publication | BMC biotechnology | Abbreviated Journal | Bmc Biotechnol |
| Volume | Issue | Pages | |||
| Keywords | A1 Journal article; Antwerp Surgical Training, Anatomy and Research Centre (ASTARC); Laboratory Experimental Medicine and Pediatrics (LEMP); Bio-Imaging lab; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | Background Cell transplantation is likely to become an important therapeutic tool for the treatment of various traumatic and ischemic injuries to the central nervous system (CNS). However, in many pre-clinical cell therapy studies, reporter gene-assisted imaging of cellular implants in the CNS and potential reporter gene and/or cell-based immunogenicity, still remain challenging research topics. Results In this study, we performed cell implantation experiments in the CNS of immunocompetent mice using autologous (syngeneic) luciferase-expressing bone marrow-derived stromal cells (BMSC-Luc) cultured from ROSA26-L-S-L-Luciferase transgenic mice, and BMSC-Luc genetically modified using a lentivirus encoding the enhanced green fluorescence protein (eGFP) and the puromycin resistance gene (Pac) (BMSC-Luc/eGFP/Pac). Both reporter gene-modified BMSC populations displayed high engraftment capacity in the CNS of immunocompetent mice, despite potential immunogenicity of introduced reporter proteins, as demonstrated by real-time bioluminescence imaging (BLI) and histological analysis at different time-points post-implantation. In contrast, both BMSC-Luc and BMSC-Luc/eGFP/Pac did not survive upon intramuscular cell implantation, as demonstrated by real-time BLI at different time-points post-implantation. In addition, ELISPOT analysis demonstrated the induction of IFN-ã-producing CD8+ T-cells upon intramuscular cell implantation, but not upon intracerebral cell implantation, indicating that BMSC-Luc and BMSC-Luc/eGFP/Pac are immune-tolerated in the CNS. However, in our experimental transplantation model, results also indicated that reporter gene-specific immune-reactive T-cell responses were not the main contributors to the immunological rejection of BMSC-Luc or BMSC-Luc/eGFP/Pac upon intramuscular cell implantation. Conclusion We here demonstrate that reporter gene-modified BMSC derived from ROSA26-L-S-L-Luciferase transgenic mice are immune-tolerated upon implantation in the CNS of syngeneic immunocompetent mice, providing a research model for studying survival and localisation of autologous BMSC implants in the CNS by real-time BLI and/or histological analysis in the absence of immunosuppressive therapy. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | London | Editor | ||
| Language | Wos | 000262698500001 | Publication Date | 2009-01-07 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1472-6750 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 2.415 | Times cited | 33 | Open Access | |
| Notes | Approved | Most recent IF: 2.415; 2009 IF: 2.723 | |||
| Call Number | UA @ lucian @ c:irua:72911 | Serial |
4527 | ||
| Permanent link to this record | |||||
| Author | Trenchev, G.; Kolev, S.; Kiss’ovski, Z. | ||||
| Title | Modeling a Langmuir probe in atmospheric pressure plasma at different EEDFs | Type | A1 Journal article | ||
| Year | 2017 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 26 | Issue | 26 | Pages | 055013 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | In this study, we present a computational model of a cylindrical electric probe in atmospheric pressure argon plasma. The plasma properties are varied in terms of density and electron temperature. Furthermore, results for plasmas with Maxwellian and non-Maxwellian electron energy distribution functions are also obtained and compared. The model is based on the fluid description of plasma within the COMSOL software package. The results for the ion saturation current are compared and show good agreement with existing analytical Langmuir probe theories. A strong dependence between the ion saturation current and electron transport properties was observed, and attributed to the effects of ambipolar diffusion. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000398327900002 | Publication Date | 2017-04-03 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 4 | Open Access | OpenAccess |
| Notes | Approved | Most recent IF: 3.302 | |||
| Call Number | PLASMANT @ plasmant @ c:irua:141914 | Serial |
4535 | ||
| Permanent link to this record | |||||
| Author | Tennyson, J.; Rahimi, S.; Hill, C.; Tse, L.; Vibhakar, A.; Akello-Egwel, D.; Brown, D.B.; Dzarasova, A.; Hamilton, J.R.; Jaksch, D.; Mohr, S.; Wren-Little, K.; Bruckmeier, J.; Agarwal, A.; Bartschat, K.; Bogaerts, A.; Booth, J.-P.; Goeckner, M.J.; Hassouni, K.; Itikawa, Y.; Braams, B.J.; Krishnakumar, E.; Laricchiuta, A.; Mason, N.J.; Pandey, S.; Petrovic, Z.L.; Pu, Y.-K.; Ranjan, A.; Rauf, S.; Schulze, J.; Turner, M.M.; Ventzek, P.; Whitehead, J.C.; Yoon, J.-S. | ||||
| Title | QDB: a new database of plasma chemistries and reactions | Type | A1 Journal article | ||
| Year | 2017 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 26 | Issue | 26 | Pages | 055014 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | One of the most challenging and recurring problems when modeling plasmas is the lack of data on the key atomic and molecular reactions that drive plasma processes. Even when there are data for some reactions, complete and validated datasets of chemistries are rarely available. This hinders research on plasma processes and curbs development of industrial applications. The QDB project aims to address this problem by providing a platform for provision, exchange, and validation of chemistry datasets. A new data model developed for QDB is presented. QDB collates published data on both electron scattering and heavy-particle reactions. These data are formed into reaction sets, which are then validated against experimental data where possible. This process produces both complete chemistry sets and identifies key reactions that are currently unreported in the literature. Gaps in the datasets can be filled using established theoretical methods. Initial validated chemistry sets for SF6/CF4/O2 and SF6/CF4/N2/H2 are presented as examples. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000398394500001 | Publication Date | 2017-04-04 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 18 | Open Access | OpenAccess |
| Notes | Approved | Most recent IF: 3.302 | |||
| Call Number | PLASMANT @ plasmant @ c:irua:142206 | Serial |
4549 | ||
| Permanent link to this record | |||||
| Author | Sun, S.R.; Kolev, S.; Wang, H.X.; Bogaerts, A. | ||||
| Title | Investigations of discharge and post-discharge in a gliding arc: a 3D computational study | Type | A1 Journal article | ||
| Year | 2017 | Publication | Plasma sources science and technology | Abbreviated Journal | Plasma Sources Sci T |
| Volume | 26 | Issue | 26 | Pages | 055017 |
| Keywords | A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
| Abstract | In this study we quantitatively investigate for the first time the plasma characteristics of an argon gliding arc with a 3D model. The model is validated by comparison with available experimental data from literature and a reasonable agreement is obtained for the calculated gas temperature and electron density. A complete arc cycle is modeled from initial ignition to arc decay. We investigate how the plasma characteristics, i.e., the electron temperature, gas temperature, reduced electric field, and the densities of electrons, Ar+ and Ar2+ ions and Ar(4s) excited states, vary over one complete arc cycle, including their behavior in the discharge and post-discharge. These plasma characteristics exhibit a different evolution over one arc cycle, indicating that either the active discharge stage or the post-discharge stage can be beneficial for certain applications. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Wos | 000399278100002 | Publication Date | 2017-04-05 | |
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 1361-6595 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
| Impact Factor | 3.302 | Times cited | 11 | Open Access | OpenAccess |
| Notes | This work is financially supported by the Methusalem financing, by the Fund for Scientific Research Flanders (FWO) and by the IAP/7 (Inter-university Attraction Pole) program ‘Physical Chemistry of Plasma-Surface Interactions’ from the Belgian Federal Office for Science Policy (BELSPO). The work was carried out in part using the Turing HPC infrastructure of the CalcUA core facility of the Universiteit Antwerpen, a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the Universiteit Antwerpen. This work was also supported by the National Natural Science Foundation of China (Grant Nos. 11275021, 11575019). SR Sun thanks the financial support from the China Scholarship Council (CSC). | Approved | Most recent IF: 3.302 | ||
| Call Number | PLASMANT @ plasmant @ c:irua:142204 | Serial |
4550 | ||
| Permanent link to this record | |||||