|
“Importance of design and operating parameters in a sonication system for viscous solutions : effects of input power, horn tip diameter and reactor capacity”. Bampouli A, Goris Q, Hussain MN, Louisnard O, Stefanidis GD, Van Gerven T, Chemical engineering and processing 198, 109715 (2024). http://doi.org/10.1016/J.CEP.2024.109715
Abstract: This study investigates the distribution of ultrasound (US) energy in a batch system for solutions with viscosity ranging from 1 to approximately 3000 mPas. Sonication was performed using horn type configurations operating at 20-30 kHz and rated power capacity of 50 or 200 W. Two different tip diameters (3 or 7 mm) and two insertion depths (35 or 25 mm) within vessels of different sizes ( approximate to 60 or 130 ml) were utilized. Additionally, a special conical tip design was employed. For each experimental setup, the calorimetric efficiency was estimated, the cavitationally active regions were visualized using the sonochemiluminescence (SCL) method and bubble cluster formation inside the vessel was macroscopically observed using a high speed camera (HSC). In the viscosity range tested, the calorimetry results showed that the efficiency and continuous operation of the device depend on both the rated power and the horn tip diameter. The ratio between electrical and calorimetric power input remained consistently around 40 to 50% across the different configurations for water, but for the 123.2 mPas solution exhibited significant variation ranging from 40 to 85%. Moreover, the power density in the smaller reactor was found to be nearly double compared to the larger one. The SCL analysis showed multiple cavitationally active zones in all setups, and the zones intensity decreased considerably with increase of the solutions viscosity. The results for the cone tip were not conclusive, but can be used as the basis for further investigation. The current research highlights the importance of thoroughly understanding the impact of each design parameter, and of establishing characterization methodologies to assist in the future development of scaled-up, commercial applications.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 4.3
DOI: 10.1016/J.CEP.2024.109715
|
|
|
“Two new members of the covalent organic frameworks family : crystalline 2D-oxocarbon and 3D-borocarbon structures”. Hassani N, Movafegh-Ghadirli A, Mahdavifar Z, Peeters FM, Neek-Amal M, Computational materials science 241, 1 (2024). http://doi.org/10.1016/J.COMMATSCI.2024.113022
Abstract: Oxocarbons, known for over two centuries, have recently revealed a long-awaited facet: two-dimensional crystalline structures. Employing an intelligent global optimization algorithm (IGOA) alongside densityfunctional calculations, we unearthed a quasi -flat oxocarbon (C 6 0 6 ), featuring an oxygen -decorated hole, and a novel 3D-borocarbon. Comparative analyses with recently synthesized isostructures, such as 2D -porous carbon nitride (C 6 N 6 ) and 2D -porous boroxine (B 6 0 6 ), highlight the unique attributes of these compounds. All structures share a common stoichiometry of X 6 Y 6 (which we call COF-66), where X = B, C, and Y = B, N, O (with X not equal Y), exhibiting a 2D -crystalline structure, except for borocarbon C 6 B 6 , which forms a 3D crystal. In our comprehensive study, we conducted a detailed exploration of the electronic structure of X 6 Y 6 compounds, scrutinizing their thermodynamic properties and systematically evaluating phonon stability criteria. With expansive surface areas, diverse pore sizes, biocompatibility, pi-conjugation, and distinctive photoelectric properties, these structures, belonging to the covalent organic framework (COF) family, present enticing prospects for fundamental research and hold potential for biosensing applications.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.3
DOI: 10.1016/J.COMMATSCI.2024.113022
|
|
|
“Refinement of the uranium dispersion corrections from anomalous diffraction”. Leinders G, Grendal OG, Arts I, Bes R, Prozheev I, Orlat S, Fitch A, Kvashnina K, Verwerft M, Journal of applied crystallography 57, 284 (2024). http://doi.org/10.1107/S1600576723010889
Abstract: The evolution of the uranium chemical state in uranium compounds, principally in the oxides, is of concern in the context of nuclear fuel degradation under storage and repository conditions, and in accident scenarios. The U–O system shows complicated phase relations between single-valence uranium dioxide (UO<sub>2</sub>) and different mixed-valence compounds (<italic>e.g.</italic>U<sub>4</sub>O<sub>9</sub>, U<sub>3</sub>O<sub>7</sub>and U<sub>3</sub>O<sub>8</sub>). To try resolving the electronic structure associated with unique atomic positions, a combined application of diffraction and spectroscopic techniques, such as diffraction anomalous fine structure (DAFS), can be considered. Reported here is the application of two newly developed routines for assessing a DAFS data set, with the aim of refining the uranium X-ray dispersion corrections. High-resolution anomalous diffraction data were acquired from polycrystalline powder samples of UO<sub>2</sub>(containing tetravalent uranium) and potassium uranate (KUO<sub>3</sub>, containing pentavalent uranium) using synchrotron radiation in the vicinity of the U<italic>L</italic><sub>3</sub>edge (17.17 keV). Both routines are based on an iterative refinement of the dispersion corrections, but they differ in either using the intensity of a selection of reflections or doing a full-pattern (Rietveld method) refinement. The uranium dispersion corrections obtained using either method are in excellent agreement with each other, and they show in great detail the chemical shifts and differences in fine structure expected for tetravalent and pentavalent uranium. This approach may open new possibilities for the assessment of other, more complicated, materials such as mixed-valence compounds. Additionally, the DAFS methodology can offer a significant resource optimization because each data set contains both structural (diffraction) and chemical (spectroscopy) information, which can avoid the requirement to use multiple experimental stations at synchrotron sources.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 6.1
DOI: 10.1107/S1600576723010889
|
|
|
“Shifts in mycorrhizal types of fungi and plants in response to fertilisation, warming and herbivory in a tundra grassland”. Le Noir de Carlan C, Kaarlejarvi E, De Tender C, Heinecke T, Eskelinen A, Verbruggen E, New phytologist (2024). http://doi.org/10.1111/NPH.19816
Abstract: Climate warming is severely affecting high-latitude regions. In the Arctic tundra, it may lead to enhanced soil nutrient availability and interact with simultaneous changes in grazing pressure. It is presently unknown how these concurrently occurring global change drivers affect the root-associated fungal communities, particularly mycorrhizal fungi, and whether changes coincide with shifts in plant mycorrhizal types. We investigated changes in root-associated fungal communities and mycorrhizal types of the plant community in a 10-yr factorial experiment with warming, fertilisation and grazing exclusion in a Finnish tundra grassland. The strongest determinant of the root-associated fungal community was fertilisation, which consistently increased potential plant pathogen abundance and had contrasting effects on the different mycorrhizal fungal types, contingent on other treatments. Plant mycorrhizal types went through pronounced shifts, with warming favouring ecto- and ericoid mycorrhiza but not under fertilisation and grazing exclusion. Combination of all treatments resulted in dominance by arbuscular mycorrhizal plants. However, shifts in plant mycorrhizal types vs fungi were mostly but not always aligned in their magnitude and direction. Our results show that our ability to predict shifts in symbiotic and antagonistic fungal communities depend on simultaneous consideration of multiple global change factors that jointly alter plant and fungal communities.
Keywords: A1 Journal article; Plant and Ecosystems (PLECO) – Ecology in a time of change
Impact Factor: 9.4
DOI: 10.1111/NPH.19816
|
|
|
“Giant tunability of Rashba splitting at cation-exchanged polar oxide interfaces by selective orbital hybridization”. Xu H, Li H, Gauquelin N, Chen X, Wu W-F, Zhao Y, Si L, Tian D, Li L, Gan Y, Qi S, Li M, Hu F, Sun J, Jannis D, Yu P, Chen G, Zhong Z, Radovic M, Verbeeck J, Chen Y, Shen B, Advanced materials (2024). http://doi.org/10.1002/ADMA.202313297
Abstract: The 2D electron gas (2DEG) at oxide interfaces exhibits extraordinary properties, such as 2D superconductivity and ferromagnetism, coupled to strongly correlated electrons in narrow d-bands. In particular, 2DEGs in KTaO3 (KTO) with 5d t2g orbitals exhibit larger atomic spin-orbit coupling and crystal-facet-dependent superconductivity absent for 3d 2DEGs in SrTiO3 (STO). Herein, by tracing the interfacial chemistry, weak anti-localization magneto-transport behavior, and electronic structures of (001), (110), and (111) KTO 2DEGs, unambiguously cation exchange across KTO interfaces is discovered. Therefore, the origin of the 2DEGs at KTO-based interfaces is dramatically different from the electronic reconstruction observed at STO interfaces. More importantly, as the interface polarization grows with the higher order planes in the KTO case, the Rashba spin splitting becomes maximal for the superconducting (111) interfaces approximately twice that of the (001) interface. The larger Rashba spin splitting couples strongly to the asymmetric chiral texture of the orbital angular moment, and results mainly from the enhanced inter-orbital hopping of the t2g bands and more localized wave functions. This finding has profound implications for the search for topological superconductors, as well as the realization of efficient spin-charge interconversion for low-power spin-orbitronics based on (110) and (111) KTO interfaces. An unambiguous cation exchange is discovered across the interfaces of (001), (110), and (111) KTaO3 2D electron gases fabricated at room temperature. Remarkably, the (111) interfaces with the highest superconducting transition temperature also turn out to show the strongest electron-phonon interaction and the largest Rashba spin splitting. image
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 29.4
DOI: 10.1002/ADMA.202313297
|
|
|
“Interlink between Abnormal Water Imbibition in Hydrophilic and Rapid Flow in Hydrophobic Nanochannels”. Zhou R, Neek-Amal M, Peeters FM, Bai B, Sun C, Physical Review Letters 132, 184001 (2024). http://doi.org/10.1103/PhysRevLett.132.184001
Abstract: Nanoscale extension and refinement of the Lucas-Washburn model is presented with a detailed analysis of recent experimental data and extensive molecular dynamics simulations to investigate rapid water flow and water imbibition within nanocapillaries. Through a comparative analysis of capillary rise in hydrophilic nanochannels, an unexpected reversal of the anticipated trend, with an abnormal peak, of imbibition length below the size of 3 nm was discovered in hydrophilic nanochannels, surprisingly sharing the same physical origin as the well-known peak observed in flow rate within hydrophobic nanochannels. The extended imbibition model is applicable across diverse spatiotemporal scales and validated against simulation results and existing experimental data for both hydrophilic and hydrophobic
Keywords: A1 Journal Article; CMT
Impact Factor: 8.6
Times cited: 1
DOI: 10.1103/PhysRevLett.132.184001
|
|
|
“Scaling-Up Microwave-Assisted Synthesis of Highly Defective Pd@UiO-66-NH2Catalysts for Selective Olefin Hydrogenation under Ambient Conditions”. Guerrero RM, Lemir ID, Carrasco S, Fernández-Ruiz C, Kavak S, Pizarro P, Serrano DP, Bals S, Horcajada P, Pérez Y, ACS Applied Materials &, Interfaces (2024). http://doi.org/10.1021/acsami.4c03106
Abstract: The need to develop green and cost-effective industrial catalytic processes has led to growing interest in preparing more robust, efficient, and selective heterogeneous catalysts at a large scale. In this regard, microwave-assisted synthesis is a fast method for fabricating heterogeneous catalysts (including metal oxides, zeolites, metal–organic frameworks, and supported metal nanoparticles) with enhanced catalytic properties, enabling synthesis scale-up. Herein, the synthesis of nanosized UiO-66-NH2 was optimized via a microwave-assisted hydrothermal method to obtain defective matrices essential for the stabilization of metal nanoparticles, promoting catalytically active sites for hydrogenation reactions (760 kg·m–3·day–1 space time yield, STY). Then, this protocol was scaled up in a multimodal microwave reactor, reaching 86% yield (ca. 1 g, 1450 kg·m–3·day–1 STY) in only 30 min. Afterward, Pd nanoparticles were formed in situ decorating the nanoMOF by an effective and fast microwave-assisted hydrothermal method, resulting in the formation of Pd@UiO-66-NH2 composites. Both the localization and oxidation states of Pd nanoparticles (NPs) in the MOF were achieved using high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) and X-ray photoelectron spectroscopy (XPS), respectively. The optimal composite, loaded with 1.7 wt % Pd, exhibited an extraordinary catalytic activity (>95% yield, 100% selectivity) under mild conditions (1 bar H2, 25 °C, 1 h reaction time), not only in the selective hydrogenation of a variety of single alkenes (1-hexene, 1-octene, 1-tridecene, cyclohexene, and tetraphenyl ethylene) but also in the conversion of a complex mixture of alkenes (i.e., 1-hexene, 1-tridecene, and anethole). The results showed a powerful interaction and synergy between the active phase (Pd NPs) and the catalytic porous scaffold (UiO-66-NH2), which are essential for the selectivity and recyclability.
Keywords: A1 Journal Article; Electron Microscopy for Materials Science (EMAT) ;
Impact Factor: 9.5
DOI: 10.1021/acsami.4c03106
|
|
|
“Comment on “Misinterpretation of the Shuttleworth equation””. Faraji F, Neyts EC, Milošević, MV, Peeters FM, Scripta Materialia 250, 116186 (2024). http://doi.org/10.1016/j.scriptamat.2024.116186
Keywords: A1 Journal Article; CMT
Impact Factor: 6
DOI: 10.1016/j.scriptamat.2024.116186
|
|
|
“Single Crystal and Pentatwinned Gold Nanorods Result in Chiral Nanocrystals with Reverse Handedness”. Van Gordon K, Ni B, Girod R, Mychinko M, Bevilacqua F, Bals S, Liz‐Marzán LM, Angewandte Chemie International Edition (2024). http://doi.org/10.1002/anie.202403116
Abstract: Handedness is an essential attribute of chiral nanocrystals, having a major influence on their properties. During chemical growth, the handedness of nanocrystals is usually tuned by selecting the corresponding enantiomer of chiral molecules involved in asymmetric growth, often known as chiral inducers. We report that, even using the same chiral inducer enantiomer, the handedness of chiral gold nanocrystals can be reversed by using Au nanorod seeds with either single crystalline or pentatwinned structure. This effect holds for chiral growth induced both by amino acids and by chiral micelles. Although it was challenging to discern the morphological handedness for<italic>L</italic>‐cystine‐directed particles, even using electron tomography, both cases showed circular dichroism bands of opposite sign, with nearly mirrored chiroptical signatures for chiral micelle‐directed growth, along with quasi‐helical wrinkles of inverted handedness. These results expand the chiral growth toolbox with an effect that might be exploited to yield a host of interesting morphologies with tunable optical properties.
Keywords: A1 Journal Article; Electron Microscopy for Materials Science (EMAT) ;
Impact Factor: 16.6
DOI: 10.1002/anie.202403116
|
|
|
“High-Throughput Morphological Chirality Quantification of Twisted and Wrinkled Gold Nanorods”. Vlasov E, Heyvaert W, Ni B, Van Gordon K, Girod R, Verbeeck J, Liz-Marzán LM, Bals S, ACS Nano (2024). http://doi.org/10.1021/acsnano.4c02757
Abstract: Chirality in gold nanostructures offers an exciting opportunity to tune their differential optical response to left- and right-handed circularly polarized light, as well as their interactions with biomolecules and living matter. However, tuning and understanding such interactions demands quantification of the structural features that are responsible for the chiral behavior. Electron tomography (ET) enables structural characterization at the single-particle level and has been used to quantify the helicity of complex chiral nanorods. However, the technique is time-consuming and consequently lacks statistical value. To address this issue, we introduce herein a high-throughput methodology that combines images acquired by secondary electron-based electron beam-induced current (SEEBIC) with quantitative image analysis. As a result, the geometric chirality of hundreds of nanoparticles can be quantified in less than 1 h. When combining the drastic gain in data collection efficiency of SEEBIC with a limited number of ET data sets, a better understanding of how the chiral structure of individual chiral nanoparticles translates into the ensemble chiroptical response can be reached.
Keywords: A1 Journal Article; Electron Microscopy for Materials Science (EMAT) ;
Impact Factor: 17.1
DOI: 10.1021/acsnano.4c02757
|
|
|
“Capillary Condensation of Water in Graphene Nanocapillaries”. Faraji F, Neyts EC, Milošević, MV, Peeters FM, Nano Letters 24, 5625 (2024). http://doi.org/10.1021/acs.nanolett.4c01088
Abstract: Recent experiments have revealed that the macroscopic Kelvin equation remains surprisingly accurate even for nanoscale capillaries. This phenomenon was so far explained by the oscillatory behavior of the solid−liquid interfacial free energy. We here demonstrate thermodynamic and capillarity inconsistencies with this explanation. After revising the Kelvin equation, we ascribe its validity at nanoscale confinement to the effect of disjoining pressure.
To substantiate our hypothesis, we employed molecular dynamics simulations to evaluate interfacial heat transfer and wetting properties. Our assessments unveil a breakdown in a previously established proportionality between the work of adhesion and the Kapitza conductance at capillary heights below 1.3 nm, where the dominance of the work of adhesion shifts primarily from energy to entropy. Alternatively, the peak density of the initial water layer can effectively probe the work of adhesion. Unlike under bulk conditions, high confinement renders the work of adhesion entropically unfavorable.
Keywords: A1 Journal Article; CMT
Impact Factor: 10.8
DOI: 10.1021/acs.nanolett.4c01088
|
|
|
“Control of proton transport and hydrogenation in double-gated graphene”. Tong J, Fu Y, Domaretskiy D, Della Pia F, Dagar P, Powell L, Bahamon D, Huang S, Xin B, Costa Filho RN, Vega LF, Grigorieva IV, Peeters FM, Michaelides A, Lozada-Hidalgo M, Nature 630, 619 (2024). http://doi.org/10.1038/s41586-024-07435-8
Abstract: The basal plane of graphene can function as a selective barrier that is permeable to protons but impermeable to all ions and gases, stimulating its use in applications such as membranes, catalysis and isotope separation. Protons can chemically adsorb on graphene and hydrogenate it, inducing a conductor–insulator transition that has been explored intensively in graphene electronic devices. However, both processes face energy barriersand various strategies have been proposed to accelerate proton transport, for example by introducing vacancies, incorporating catalytic metalsor chemically functionalizing the lattice. But these techniques can compromise other properties, such as ion selectivity or mechanical stability. Here we show that independent control of the electric field,<italic>E</italic>, at around 1 V nm<sup>−1</sup>, and charge-carrier density,<italic>n</italic>, at around 1 × 10<sup>14</sup> cm<sup>−2</sup>, in double-gated graphene allows the decoupling of proton transport from lattice hydrogenation and can thereby accelerate proton transport such that it approaches the limiting electrolyte current for our devices. Proton transport and hydrogenation can be driven selectively with precision and robustness, enabling proton-based logic and memory graphene devices that have on–off ratios spanning orders of magnitude. Our results show that field effects can accelerate and decouple electrochemical processes in double-gated 2D crystals and demonstrate the possibility of mapping such processes as a function of<italic>E</italic>and<italic>n</italic>, which is a new technique for the study of 2D electrode–electrolyte interfaces.
Keywords: A1 Journal Article; Condensed Matter Theory (CMT) ;
Impact Factor: 64.8
DOI: 10.1038/s41586-024-07435-8
|
|
|
“Synergy or Antagonism? Exploring the Interplay of SnO2and an N-OMC Carbon Capture Medium for the Electrochemical CO2Reduction toward Formate”. Van Daele K, Balalta D, Hoekx S, Jacops R, Daems N, Altantzis T, Pant D, Breugelmans T, ACS Applied Energy Materials 7, 5517 (2024). http://doi.org/10.1021/acsaem.4c00994
Abstract: Closing the anthropogenic carbon cycle by means of the sustainable electrochemical CO2 reduction (eCO2R) toward formate (FA) is a promising strategy for CO2 abatement, clearing the path toward a carbon neutral future. Currently, three possible reaction pathways have been identified for the eCO2R toward FA, all of which are initiated by the adsorption of CO2 on the electrocatalyst’s surface. Therefore, a possible strategy to enhance the availability of CO2 near the active sites is to combine an active electrocatalyst material (here, SnO2) with a known carbon capture medium (here, nitrogen-doped ordered mesoporous carbon (N-OMC)). SnO2 was introduced in situ during the N-OMC synthesis, yielding SnO2-N-OMCs. We approached the state of the art for Sn-based N-doped carbon electrocatalysts in terms of performance under industrially relevant currents with an average FEFA of 59% for SnO2-N-OMC (6) and 61% for SnO2-N-OMC (2). Moreover, the SnO2-N-OMC electrocatalysts require a low overpotential, courtesy of the N-OMC support, compared to the state of the art, for the selective conversion of CO2 toward FA at the industrially relevant current density of 100 mA cm–2. Additionally, the 24 h stability of the best performing SnO2-N-OMC electrocatalysts is explored, and pulverization/agglomeration and in situ SnO2 reduction are identified as major degradation pathways, allowing future research to be steered more accurately toward more stable Sn-based electrocatalysts for the eCO2R toward FA. An optimal combination of both the SnO2 species and the N-OMC carbon capture medium could result in a synergistic effect, especially when utilization of the N-OMC support material is optimized to morphologically stabilize the SnO2 active species.
Keywords: A1 Journal Article; nitrogen-doped ordered mesoporous carbon, SnO2, degradation pathways, electrochemical CO2 reduction, formate; Electron Microscopy for Materials Science (EMAT) ;
Impact Factor: 6.4
DOI: 10.1021/acsaem.4c00994
|
|
|
“Grain boundary-mediated plasticity in aluminum films unraveled by a statistical approach combining nano-DIC and ACOM-TEM”. Baral P, Kashiwar A, Coulombier M, Delannay L, Hoummada K, Raskin JP, Idrissi H, Pardoen T, Acta materialia 276, 120081 (2024). http://doi.org/10.1016/J.ACTAMAT.2024.120081
Abstract: Nanomechanical on-chip testing is combined with nanoscale in situ digital image correlation and automated crystal orientation mapping in TEM to deliver novel statistically representative quantitative data about the deformation mechanisms in nanocrystalline aluminum films. The films are very ductile, with a rare stable multiple necking process with local strains reaching up to 0.45 and macroscopic elongation up to 0.17. The strain fields with resolution below 100 nm are related to the underlying microstructure and crystallographic orientation maps. This reveals nanoscopic shear bands forming preferentially along GB with high misorientations, tilted at +/− 45° with respect to loading direction. The analysis of these data prove that the strong strain delocalization process is promoted by GB migration and grain rotation, leading to large strain rate sensitivity. The distribution of misorientation angles between grains evolve during deformation. The GBs with misorientation between 20° and 40°, which are the GBs with highest energy, involve the largest strains.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 9.4
DOI: 10.1016/J.ACTAMAT.2024.120081
|
|
|
“Toward the rational design of Cu electrocatalysts for improved performance of the NO3RR”. Hoekx S, Daems N, Arenas Esteban D, Bals S, Breugelmans T, ACS applied energy materials 7, 3761 (2024). http://doi.org/10.1021/ACSAEM.3C03207
Abstract: Cu is one of the most promising materials as an electrocatalyst for the nitrate reduction reaction (NO3RR) to ammonia, a reaction that can simultaneously remove nitrates from wastewater and produce ammonia, a high-value commodity chemical. However, a rational approach to catalyst design is lacking, limiting efficient catalyst optimization. In this work, we propose a way to synthesize monodisperse, polycrystalline Cu NPs with small variances in size by changing the carbon chain length of the phosphonic acid-based ligand. Cu NPs with 8.3, 10.0, and 11.9 nm diameters are successfully synthesized, and high-resolution electron microscopy and tomography are used to characterize these NPs in depth. By isolating Cu NP size as a parameter, we can unequivocally establish its effect on electrochemical performance for the NO3RR to ammonia under optimal operating conditions for the catalyst (0.1 M KOH electrolyte at -1.25 V vs RHE, as established in the first phase). The smallest Cu NPs (8.3 nm with a TDPA ligand) perform best, achieving Faradaic efficiencies (FEs) of 85.4% and absolute current densities of similar to 250 mA cm(-2), with increasing current densities and constant FEs as the particle size decreases. To allow for a rational approach to Cu-based catalyst design from a stability perspective, this work completed a first study of the main degradation pathway that the Cu NPs undergo during NO3RR. High-resolution electron microscopy and tomography are used to characterize the particles at various stages of the reaction. The NPs undergo agglomeration, pulverization, and particle detachment due to the reaction, starting at a particle size of 8.3 nm and progressively getting smaller, but leveling off, until a NP size of 2.6 nm is reached after 2 h of electrolysis. This decrease in NP size goes paired with a decrease in FE from 83% after the first 15 min to 74% after 2 h at -0.75 V vs RHE, despite the increase in active surface area. These insights into the most prominent degradation mechanisms allow for rational adjustments to future catalysts to combat these changes; for example, by embedding NPs in a tailored support, morphological degradation could be impeded. Therefore, these insights allow for a rational approach to the improvement of the stability of Cu-based catalysts for the NO3RR, a very important but often an overlooked aspect of catalyst design.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Applied Electrochemistry & Catalysis (ELCAT)
Impact Factor: 6.4
DOI: 10.1021/ACSAEM.3C03207
|
|
|
“The synergistic influence of metal cations on the drying and viscosity of linseed oil assessed by means of model samples containing synthesised metal carboxylates”. Kirkpatrick S, Sanyova J, Janssens K, van der Snickt G, Heritage science 12, 209 (2024). http://doi.org/10.1186/S40494-024-01309-Y
Abstract: The recent multi-analytical study carried out on the Van Eyck's Ghent Altarpiece showed the simultaneous presence of several kinds of metal carboxylates in oil-rich glaze layers. This outcome raised the question whether these carboxylates had already formed during the preparation of the oil binder by the artists. In the case of early-stage formation, they may have had an impact on the drying rate of the resulting oil, as well as on its handling properties. This hypothesis was investigated using a model system of in-house-prepared linseed oil containing incremental concentrations (2-5-10 wt.%) of relevant metal carboxylates (i.e. Ca-, Zn-, Cu-, and Pb oleates and stearates). This paper describes the influence of these type of molecules on the drying rate of linseed oil and, to an extent, on its viscosity. The drying time of the linseed oil, to which one or more metal carboxylates were added, was measured with a drying recorder while the viscosity was assessed with a rheometer. When introduced together, some of these metal carboxylates act in synergy to shorten the drying time with respect to the situation when the same metal carboxylates were added separately to linseed oil. Mixtures of Ca- and Zn-oleates proved to have a larger effect than other binary combinations. Addition of two metal oleates (combination of Ca/Zn/Cu/Pb) reduced the drying time even more. On the other hand, specific combinations of three metal stearates and/or oleates also demonstrated a significant synergistic effect towards increasing the viscosity of the binder. Especially combinations of Ca/Zn/Cu and Ca/Zn/Pb stearates and oleates gave rise to the highest level of linseed oil viscosity increase, when compared to the situation in which the same metal carboxylates were added separately.
Keywords: A1 Journal article; Art; Antwerp Cultural Heritage Sciences (ARCHES); Antwerp X-ray Imaging and Spectroscopy (AXIS)
Impact Factor: 2.5
DOI: 10.1186/S40494-024-01309-Y
|
|
|
“The potential of electrochemical sensors to unveil counterfeits : Xanax as a case study”. Mazurkow JM, Montiel FN, Van Echelpoel R, Kusior A, De Wael K, Electrochimica acta 494, 144458 (2024). http://doi.org/10.1016/J.ELECTACTA.2024.144458
Abstract: The illicit drug market has been constantly evolving in the last decades, with a significant rise in counterfeit medicines posing serious public health risks. Benzodiazepines (BZDs) such as alprazolam (generally sold under the brand name Xanax), have particularly become the target of counterfeiting efforts due to their addictive nature and upsurge of unregulated designer BZDs. These counterfeit versions frequently resemble legitimate products but contain harmful adulterants or other potent illicit substances. Few methods have been developed to tackle counterfeit pills, usually limited to accurate and sophisticated laboratory equipment. This study explores the feasibility of combining electrochemical fingerprinting with data analysis to overcome the limitations of traditional methods. First, the electrochemical behavior of selected BZDs is studied, and analytical parameters such as pH are optimized. Then, the electroanalysis of common adulterants and illicit drugs is addressed and integrated into a user-friendly app, including a flowchart system. The proposed electrochemical strategy enables the detection of counterfeit Xanax by identifying the presence or absence of alprazolam. It also allows determination of the alprazolam content within a pill while meeting the fundamental requirements of the end users. This study represents an on-site methodology to address the growing challenges posed by BZDs, easily transferable to counterfeit medicines from other drug groups.
Keywords: A1 Journal article; Antwerp Electrochemical and Analytical Sciences Lab (A-Sense Lab); Antwerp engineering, PhotoElectroChemistry & Sensing (A-PECS)
Impact Factor: 6.6
DOI: 10.1016/J.ELECTACTA.2024.144458
|
|
|
“Imaging the suppression of ferromagnetism in LaMnO₃, by metallic overlayers”. Folkers B, Jansen T, Roskamp TJ, Reith P, Timmermans A, Jannis D, Gauquelin N, Verbeeck J, Hilgenkamp H, Rosario CMM, Physical review materials 8, 054408 (2024). http://doi.org/10.1103/PHYSREVMATERIALS.8.054408
Abstract: LaMnO 3 (LMO) thin films epitaxially grown on SrTiO 3 (STO) usually exhibit ferromagnetism above a critical layer thickness. We report the use of scanning SQUID microscopy (SSM) to study the suppression of the ferromagnetism in STO / LMO / metal structures. By partially covering the LMO surface with a metallic layer, both covered and uncovered LMO regions can be studied simultaneously. While Au does not significantly influence the ferromagnetic order of the underlying LMO film, a thin Ti layer induces a strong suppression of the ferromagnetism, over tens of nanometers, which increases with time on a timescale of days. Detailed electron energy loss spectroscopy analysis of the Ti-LaMnO 3 interface reveals the presence of Mn 2 + and an evolution of the Ti valence state from Ti 0 to Ti 4 + over approximately 5 nm. Furthermore, we demonstrate that by patterning Ti / Au overlayers, we can locally suppress the ferromagnetism and define ferromagnetic structures down to sub -micrometer scales.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.4
DOI: 10.1103/PHYSREVMATERIALS.8.054408
|
|
|
“Interlayer affected diamond electrochemistry”. Chen X, Dong X, Zhang C, Zhu M, Ahmed E, Krishnamurthy G, Rouzbahani R, Pobedinskas P, Gauquelin N, Jannis D, Kaur K, Hafez AME, Thiel F, Bornemann R, Engelhard C, Schoenherr H, Verbeeck J, Haenen K, Jiang X, Yang N, Small methods , 2301774 (2024). http://doi.org/10.1002/SMTD.202301774
Abstract: Diamond electrochemistry is primarily influenced by quantities of sp3-carbon, surface terminations, and crystalline structure. In this work, a new dimension is introduced by investigating the effect of using substrate-interlayers for diamond growth. Boron and nitrogen co-doped nanocrystalline diamond (BNDD) films are grown on Si substrate without and with Ti and Ta as interlayers, named BNDD/Si, BNDD/Ti/Si, and BNDD/Ta/Ti/Si, respectively. After detailed characterization using microscopies, spectroscopies, electrochemical techniques, and density functional theory simulations, the relationship of composition, interfacial structure, charge transport, and electrochemical properties of the interface between diamond and metal is investigated. The BNDD/Ta/Ti/Si electrodes exhibit faster electron transfer processes than the other two diamond electrodes. The interlayer thus determines the intrinsic activity and reaction kinetics. The reduction in their barrier widths can be attributed to the formation of TaC, which facilitates carrier tunneling, and simultaneously increases the concentration of electrically active defects. As a case study, the BNDD/Ta/Ti/Si electrode is further employed to assemble a redox-electrolyte-based supercapacitor device with enhanced performance. In summary, the study not only sheds light on the intricate relationship between interlayer composition, charge transfer, and electrochemical performance but also demonstrates the potential of tailored interlayer design to unlock new capabilities in diamond-based electrochemical devices. Diamond electrochemistry is revealed to be affected by the interlayers between boron/nitrogen co-doped nanocrystalline diamond (BNDD) film and a Si substrate. A BNDD/Ta/Ti/Si electrode exhibits faster electron transfer processes and smaller electron transfer resistance of redox probes for [Fe(CN)6]3-/4- and [Ru(NH3)6]3+/2+ than the other electrodes, because the interlayer thus determines the intrinsic activity and reaction kinetics of diamond films. image
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 12.4
DOI: 10.1002/SMTD.202301774
|
|
|
“Evaluation of corrosion impeding concretion layers formed on shipwreck steel in the Belgian North Sea”. Laureys A, Richardson P, Verhasselt K, Chaves IA, Melchers RE, Van Den Bergh K, Depover T, Verbeken K, Potters G, De Baere K, Corrosion 80, 539 (2024). http://doi.org/10.5006/4341
Abstract: Steel shipwrecks buried along the Belgian and French North Sea coast have proven to show very low corrosion rates due to concretion. This work aims to provide an in-depth analysis of the formed concretion layers and gain a more complete understanding of the gradual deposition processes in the North Sea. Detailed microstructural characterization by scanning electron microscopy, energy dispersive x-ray spectroscopy, and x-ray diffraction of two different specimens demonstrates that the concretion includes a complex structure of multiple layers. Closest to the metal surface, a layer of 100% akaganeite is found. It forms from corrosion products exhibiting high Cl- ions concentrations at the metal surface. Next, other iron oxides, such as goethite, lepidocrocite, and magnetite, are observed. Then, layers that both contain corrosion products and compounds from the environment are present. These layers contain calcium carbonates (calcite and aragonite), calcium sulfate (gypsum), and quartz (sand). Moreover, due to a displacement of calcium by iron, an additional phase is formed consisting out of hard, dense siderite mixed into calcite. Finally, the surface of the concretion is covered by a biofilm.
Keywords: A1 Journal article; Engineering sciences. Technology; Antwerp engineering, PhotoElectroChemistry & Sensing (A-PECS)
Impact Factor: 1.6
DOI: 10.5006/4341
|
|
|
“Magneto-optical conductivity of monolayer transition metal dichalcogenides in the presence of proximity-induced exchange interaction and external electrical field”. Li Y, Xiao YM, Xu W, Ding L, Milošević, MV, Peeters FM, Physical review B 109, 165441 (2024). http://doi.org/10.1103/PHYSREVB.109.165441
Abstract: We theoretically investigate the magneto-optical (MO) properties of monolayer (ML) transition metal dichalcogenides (TMDs) in the presence of external electrical and quantizing magnetic fields and of the proximity-induced exchange interaction. The corresponding Landau Level (LL) structure is studied by solving the Schr & ouml;dinger equation and the spin polarization in ML-TMDs under the action of the magnetic field is evaluated. The impact of trigonal warping on LLs and MO absorption is examined. Furthermore, the longitudinal MO conductivity is calculated through the dynamical dielectric function under the standard random-phase approximation (RPA) with the Kubo formula. We take ML-MoS 2 as an example to examine the effects of proximity-induced exchange interaction, external electrical and magnetic fields on the MO conductivity induced via intra- and interband electronic transitions among the LLs. For intraband electronic transitions within the conduction or valence bands, we can observe two absorption peaks in terahertz (THz) frequency range. While the interband electronic transitions between conduction and valence LLs show a series of absorption peaks in the visible range. We find that the proximity-induced exchange interaction, the carrier density, the strengths of the external electrical and magnetic fields can effectively modulate the positions of the absorption peaks and the shapes of the MO absorption spectra. The results obtained from this study can benefit to an in-depth understanding of the MO properties of ML-TMDs which can be potentially applied for magneto-optic, spintronic, and valleytronic devices working in visible to THz frequency bandwidths.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.7
DOI: 10.1103/PHYSREVB.109.165441
|
|
|
“Electron-phonon coupling and thermal conductivity of MAB compounds”. Kocabas T, Samanta B, Barboza E da S, Sevik C, Milošević, MV, Çakir D, Physical review materials 8, 055002 (2024). http://doi.org/10.1103/PHYSREVMATERIALS.8.055002
Abstract: We investigated the electron-phonon ( e -ph ) coupling and vibrational thermal conductivity in the representative MAB compounds, namely MoAlB, WAlB, Tc 2 AlB 2 , and Cr 2 AlB 2 . The spectral distribution functions of e -ph interaction, obtained through ab initio linear-response calculations, reveal that the electron-phonon coupling values range from low (0.15) to moderate (0.58). With such e -ph coupling, out of the considered compounds, only Tc 2 AlB 2 exhibits a superconducting transition, at 4 K. We further evaluated the thermal conductivity and associated properties like scattering rates, obtained using ab initio and other methodologies. The latter included the iterative solution of the Peierls-Boltzmann transport equation, using HIPHIVE package for advanced optimization and machine learning techniques, and employing maximum likelihood estimation to approximate scattering rates from a limited set of scattering processes. We found that these methods yield nearly identical predictions for thermal conductivity values, with a significant decrease in the computational cost compared to the first-principles methods. We examined interactions arising from both three-phonon (3 ph ) and four -phonon (4 ph ) scattering processes. The 4 ph interactions demonstrated a smaller yet significant impact on the overall vibrational thermal conductivity, most notably in Tc 2 AlB 2 . Our findings indicate that Cr 2 AlB 2 has the highest thermal conductivity across all considered crystal directions, with the thermal conductivity being spatially anisotropic, most pronouncedly in Tc 2 AlB 2 . Finally, we show that empirical expressions based on Slack models are well suited for screening the thermal conductivity properties of MAB phases, and can be employed to establish upper and lower limits of their thermal conductivity.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.4
DOI: 10.1103/PHYSREVMATERIALS.8.055002
|
|
|
“Enhanced piezoelectricity by polarization rotation through thermal strain manipulation in PbZr0.6Ti0.4O3 thin films”. Huang S, Houwman E, Gauquelin N, Orekhov A, Chezganov D, Verbeeck J, Hu S, Zhong G, Koster G, Rijnders G, Advanced Materials Interfaces 11, 2400048 (2024). http://doi.org/10.1002/ADMI.202400048
Abstract: Lead based bulk piezoelectric materials, e.g., PbZrxTi1-xO3 (PZT), are widely used in electromechanical applications, sensors, and transducers, for which optimally performing thin films are needed. The results of a multi-domain Landau-Ginzberg-Devonshire model applicable to clamped ferroelectric thin films are used to predict the lattice symmetry and properties of clamped PZT thin films on different substrates. Guided by the thermal strain phase diagrams that are produced by this model, experimentally structural transitions are observed. These can be related to changes of the piezoelectric properties in PZT(x = 0.6) thin films that are grown on CaF2, SrTiO3 (STO) and 70% PbMg1/3Nb2/3O3-30% PbTiO3 (PMN-PT) substrates by pulsed laser deposition. Through temperature en field dependent in situ X-ray reciprocal space mapping (RSMs) and piezoelectric force microscopy (PFM), the low symmetry monoclinic phase and polarization rotation are observed in the film on STO and can be linked to the measured enhanced properties. The study identifies a monoclinic -rhombohedral M-C-M-A-R crystal symmetry path as the polarization rotation mechanism. The films on CaF2 and PMN-PT remain in the same symmetry phase up to the ferroelectric-paraelectric phase transition, as predicted. These results support the validity of the multi-domain model which provides the possibility to predict the behavior of clamped, piezoelectric PZT thin films, and design films with enhanced properties.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 5.4
DOI: 10.1002/ADMI.202400048
|
|
|
“Longitudinal and transverse mobilities of n-type monolayer transition metal dichalcogenides in the presence of proximity-induced interactions at low temperature”. Liu J, Xu W, Xiao YM, Ding L, Li HW, Van Duppen B, Milošević, MV, Peeters FM, Physical review B 109, 195418 (2024). http://doi.org/10.1103/PHYSREVB.109.195418
Abstract: We present a detailed theoretical investigation on the electronic transport properties of n-type monolayer (ML) transition metal dichalcogenides (TMDs) at low temperature in the presence of proximity-induced interactions such as Rashba spin-orbit coupling (RSOC) and the exchange interaction. The electronic band structure is calculated by solving the Schr & ouml;dinger equation with a k <middle dot> p Hamiltonian, and the electric screening induced by electron-electron interaction is evaluated under a standard random phase approximation approach. In particular, the longitudinal and transverse or Hall mobilities are calculated by using a momentum-balance equation derived from a semiclassical Boltzmann equation, where the electron-impurity interaction is considered as the principal scattering center at low temperature. The obtained results show that the RSOC can induce the in-plane spin components for spin-split subbands in different valleys, while the exchange interaction can lift the energy degeneracy for electrons in different valleys. The opposite signs of Berry curvatures in the two valleys would introduce opposite directions of Lorentz force on valley electrons. As a result, the transverse currents from nondegenerate valleys can no longer be canceled out so that the transverse current or Hall mobility can be observed. Interestingly, we find that at a fixed effective Zeeman field, the lowest spin-split conduction subband in ML-TMDs can be tuned from one in the K'-valley to one in the K-valley by varying the Rashba parameter. The occupation of electrons in different valleys also varies with changing carrier density. Therefore, we can change the magnitude and direction of the Hall current by varying the Rashba parameter, effective Zeeman field, and carrier density by, e.g., the presence of a ferromagnetic substrate and/or applying a gate voltage. By taking the ML-MoS2 as an example, these effects are demonstrated and examined. The important and interesting theoretical findings can be beneficial to experimental observation of the valleytronic effect and to gaining an in-depth understanding of the ML-TMD systems in the presence of proximity-induced interactions.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.7
DOI: 10.1103/PHYSREVB.109.195418
|
|
|
“8-pmmn borophene : edge states in competition with Landau levels and local vacancy states”. Nazar ND, Peeters FM, Costa Filho RN, Vazifehshenas T, Physical chemistry, chemical physics 26, 16153 (2024). http://doi.org/10.1039/D3CP05638D
Abstract: The tight-binding method is used to investigate the electronic and magnetic properties of borophene nano-ribbons (BNRs) in the presence of a perpendicular magnetic field. Most BNRs exhibit metallic characteristics due to edge bands. Additionally, the appearance of Landau levels (LLs) is strongly influenced by the edge states, contrasting with the sheet platform which produces distinct LLs. We also investigated single atomic vacancy disorders in BNRs and observed localized vacancy states (LVSs) resulting from atomic disorder. Both LVSs and LLs are influenced by the edge states, underscoring that the electronic and magnetic properties of BNRs are strongly edge-dependent. This aspect is crucial for consideration in experimental, theoretical, and computational studies.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.3
DOI: 10.1039/D3CP05638D
|
|
|
“Hydrogenation-controlled band engineering of dumbbell graphene”. Song Y, Chen M, Xie X, Liu X, Li J, Peeters FM, Li L, Nano energy 127, 109763 (2024). http://doi.org/10.1016/J.NANOEN.2024.109763
Abstract: The stability of the dumbbell structure has been confirmed by previous theory and experiment. Based on firstprinciples calculations, we proposed hexagonal dumbbell graphene (HDB C10) and rectangular dumbbell graphene (RDB C10) monolayers containing periodically raised C (CR) atoms. They turn out to have high mobility semiconductor properties. By adsorbing H atoms on these CR atoms, their band structures can be widely tuned from semiconductor to semimetal. When considering adsorption of two/four H atoms on the unit cell of the dumbbell structure, the bandgap can be increased, and isolated flat band structures can be obtained by further adding or removing H atoms. Remarkably, two different Dirac band structures can be found in the HDB/RDB C10H2-I monolayers. The HDB C10H2-I shows a Dirac cone with isotropic Fermi velocities, while the RDB C10H2-I monolayer exhibits a quasi-one-dimensional Dirac nodal line with varying Fermi velocities along the XS path. Tight-binding (TB) models are constructed including nearest neighbor (NN) and next NN hopping in order to understand our DFT results. These TB models are related to the Su-Schrieffer-Heeger model, and are able to explain the tunable topological properties of the RDB C10H2-I monolayer. They not only are able to explain the different kinds of Fermi velocity, but also can predict the emergence of topological edge states, providing a good platform for research on Dirac fermions. The HDB/RDB C10 monolayer exhibits more freedom of tunable band structures and more stable hydrogen storage capacity, making it superior to graphene. Finally, possible experimental synthesis paths of these DB monolayers are provided.
Keywords: A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT)
Impact Factor: 17.6
DOI: 10.1016/J.NANOEN.2024.109763
|
|
|
“Strain and stacking registry effects on the hyperbolicity of exciton polaritons in few-layer black phosphorus”. Thomen DMN, Sevik C, Milošević, MV, Teles LK, Chaves A, Physical review B 109, 245413 (2024). http://doi.org/10.1103/PHYSREVB.109.245413
Abstract: We analyze, from first -principles calculations, the excitonic properties of monolayer black phosphorus (BP) under strain, as well as of bilayer BP with different stacking registries, as a base platform for the observation and use of hyperbolic polaritons. In the unstrained case, our results confirm the in -plane hyperbolic behavior of polaritons coupled to the ground -state excitons in both mono- and bilayer systems, as observed in recent experiments. With strain, we reveal that the exciton-polariton hyperbolicity in monolayer BP is enhanced (reduced) by compressive (tensile) strain in the zig-zag direction of the crystal. In the bilayer case, different stacking registries are shown to exhibit hyperbolic exciton polaritons with different dispersion, while also peaking at different frequencies. This renders both mechanical stress and stacking registry control as practical tools for tuning physical properties of hyperbolic exciton polaritons in black phosphorus, which facilitates detection and further optoelectronic use of these quasiparticles.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.7
DOI: 10.1103/PHYSREVB.109.245413
|
|
|
“Strong spin-lattice coupling and high-temperature magnetic ordering in monolayer chromium dichalcogenides”. Gonzalez-Garcia A, Bacaksiz C, Frauenheim T, Milošević, MV, Physical review materials 8, 064001 (2024). http://doi.org/10.1103/PHYSREVMATERIALS.8.064001
Abstract: We detail the magnetic properties of monolayer CrX2 and its Janus counterparts CrXY (X, Y = S, Se, Te, with X not equal Y) using ab initio methods and Landau-Lifshitz-Gilbert magnetization dynamics, and uncover the pronouncedly strong interplay between their structure symmetry and the magnetic order. The relaxation of nonmagnetic chalcogen atoms, that carry large spin-orbit coupling, changes the energetically preferential magnetic order between in-plane antiferromagnetic and tilted ferromagnetic one. The considered Janus monolayers exhibit sizable Dzyaloshinskii-Moriya interaction, in some cases above 20% of the isotropic exchange, and critical temperature of the long-range magnetic order in the vicinity or even significantly above the room temperature.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.4
DOI: 10.1103/PHYSREVMATERIALS.8.064001
|
|
|
“Collective excitations in three-dimensional Dirac systems”. Li QN, Vasilopoulos P, Peeters FM, Xu W, Xiao YM, Milošević, MV, Physical review B 109, 115123 (2024). http://doi.org/10.1103/PHYSREVB.109.115123
Abstract: We provide the plasmon spectrum and related properties of the three-dimensional (3D) Dirac semimetals Na 3 Bi and Cd 3 As 2 based on the random -phase approximation. The necessary one -electron eigenvalues and eigenfunctions are obtained from an effective k <middle dot> p Hamiltonian. Below the energy at which the velocity v z along the k z axis vanishes, the density of states differs drastically from that of a 3D electron gas (3DEG) or graphene. The dispersion relation is anisotropic for wave vectors parallel ( q ) and perpendicular ( q z ) to the ( x , y ) plane and is markedly different than that of graphene or a 3DEG. The same holds for the energy -loss function. Both depend sensitively on the position of the Fermi energy E F relative to the region of the Berry curvature of the bands. For E F below the energy at which v z vanishes, the range of the relevant wave vectors q and q z shrinks, for q z by about one order of magnitude.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.7
DOI: 10.1103/PHYSREVB.109.115123
|
|
|
“Cs3Bi2Br9 nanoparticles decorated C3N4 nanotubes composite photocatalyst for highly selective oxidation of benzylic alcohol”. Ding Y, Wang C, Bandaru S, Pei L, Zheng R, Hau Ng Y, Arenas Esteban D, Bals S, Zhong J, Hofkens J, Van Tendeloo G, Roeffaers MBJ, Chen L-H, Su B-L, Journal of Colloid and Interface Science 672, 600 (2024). http://doi.org/10.1016/j.jcis.2024.06.017
Abstract: Solar-light driven oxidation of benzylic alcohols over photocatalysts endows significant prospects in value-added organics evolution owing to its facile, inexpensive and sustainable process. However, the unsatisfactory performance of actual photocatalysts due to the inefficient charge separation, low photoredox potential and sluggish surface reaction impedes the practical application of this process. Herein, we developed an innovative Z-Scheme Cs3BiBr9 nanoparticles@porous C3N4 tubes (CBB-NP@P-tube-CN) heterojunction photocatalyst for highly selective benzyl alcohol oxidation. Such composite combining increased photo-oxidation potential, Z-Scheme charge migration route as well as the structural advantages of porous tubular C3N4 ensures the accelerated mass and ions diffusion kinetics, the fast photoinduced carriers dissociation and sufficient photoredox potentials. The CBB-NP@P-tube-CN photocatalyst demonstrates an exceptional performance for selective photo-oxidation of benzylic alcohol into benzaldehyde with 19, 14 and 3 times higher benzylic alcohols conversion rate than those of C3N4 nanotubes, Cs3Bi2Br9 and Cs3Bi2Br9@bulk C3N4 photocatalysts, respectively. This work offers a sustainable photocatalytic system based on lead-free halide perovskite toward large scale solar-light driven value-added chemicals production.
Keywords: A1 Journal Article; Electron Microscopy for Materials Science (EMAT) ;
Impact Factor: 9.9
DOI: 10.1016/j.jcis.2024.06.017
|
|