|
“Azimuthal and radial flow patterns of 1g-Geldart B-type particles in a gas-solid vortex reactor”. Gonzalez-Quiroga A, Kulkarni SR, Vandewalle L, Perreault P, Goel C, Heynderickx GJ, van Geem KM, Marin GB, Powder technology 354, 410 (2019). http://doi.org/10.1016/J.POWTEC.2019.06.015
Abstract: Processes requiring intensive interfacial momentum, mass and heat exchange between gases and particulate solids can be greatly enhanced by operating in a centrifugal field. This is realized in the Gas-Solid Vortex Reactor (GSVR) with centrifugal accelerations up to two orders of magnitude higher than the Earth's gravitational acceleration. Here, the flow patterns of two 1g-Geldart B-type particles are experimentally assessed, over the gas inlet velocity range 82–126 m s−1, in an 80 mm diameter and 15 mm height GSVR. The particles are monosized aluminum spheres of 0.5 mm diameter, and walnut shell in the sieve fraction 0.50–0.56 mm and aspect ratio 1.3 ± 0.2. Two dimensional Particle Image Velocimetry combined with Digital Image Analysis and pressure measurements revealed that periodic fluctuations in solids azimuthal and radial velocity between gas inlet slots are strongly related to the average solids azimuthal velocity and bed uniformity. Aluminum particles feature steeper changes in azimuthal velocity and more attenuated changes in radial velocity than walnut shell particles. Within the assessed gas inlet velocity range the solids bed of aluminum exhibits average azimuthal velocities and bed voidages 40–50% and ≈10% lower than those of walnut shell. The aerodynamic response time of the particles, i.e. ρsdp2/18μg, emerged as an important parameter to assess the influence of the carrier gas jet on the radial deflection of the particles and the interaction solids bed-outer wall. Too low aerodynamic response time relates to nonuniformity in bed voidage due to solids radial velocity fluctuations. Excessive aerodynamic response time indicates low solids azimuthal velocities due to solids bed-outer wall friction.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.POWTEC.2019.06.015
|
|
|
“Intensifying mass and heat transfer using a high-g stator-rotor vortex chamber”. Gonzalez-Quiroga A, Shtern V, Perreault P, Vandewalle L, Marin GB, Van Geem KM, Chemical Engineering And Processing 169, 108638 (2021). http://doi.org/10.1016/J.CEP.2021.108638
Abstract: Vortex reactors take advantage of the synergy between enhanced heat and mass transfer rates and multifunctional phenomena at different temporal and spatial scales. Proof-of-concept experiments with our novel and innovative STAtor-Rotor VOrtex Chamber (STARVOC) confirm its advantageous features for the sustainable production of chemicals and fuels. STARVOC is a high-g contactor that uses carrier flow (gas or liquid) tangential injection to drive a rotor attached to low-friction bearings. The vortex chamber inside the rotor contains a secondary phase or phases, such as a solids bed, a liquid layer, or a suspension. Carrier fluid passes through the perforated rotor wall and contacts a densely and uniformly distributed secondary phase with enhanced slip velocities. Experiments focused on pressure profiles, rotor angular velocity, and solids azimuthal velocity. With air as the carrier fluid and different solid particle beds as the secondary phase, STARVOC reached bed azimuthal velocities up to four-fold compared to those reached in Gas-Solid Vortex Units with fully static geometry. These results show its potential to improve interfacial heat and mass transfer rates and take advantage of flow energy and angular momentum. Due to its process intensification capabilities, STARVOC is a promising alternative for the state-of-the-art chemical industry.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 2.234
DOI: 10.1016/J.CEP.2021.108638
|
|
|
Goorden L, Van Tendeloo G, Lenaerts S, Deblonde M, et al. (2009) Nanotechnologie: gewikt en gewogen. NanoSoc
Keywords: Minutes and reports; Engineering sciences. Technology; Engineering Management (ENM); Sustainable Energy, Air and Water Technology (DuEL); Electron microscopy for materials research (EMAT)
|
|
|
Goorden L, Van Tendeloo G, Lenaerts S, Deblonde M, van Oudheusden M, et al. (2009) Nanotechnologie op de agenda. NanoSoc
Keywords: Minutes and reports; Engineering sciences. Technology; Engineering Management (ENM); Society and Environment; Sustainable Energy, Air and Water Technology (DuEL); Electron microscopy for materials research (EMAT)
|
|
|
“Transition thinking and business model innovation-towards a transformative business model and new role for the reuse centers of Limburg, Belgium”. Gorissen L, Vrancken K, Manshoven S, Sustainability 8 (2016). http://doi.org/10.3390/SU8020112
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.3390/SU8020112
|
|
|
“Growing media constituents determine the microbial nitrogen conversions in organic growing media for horticulture”. Grunert O, Reheul D, Van Labeke M-C, Perneel M, Hernandez-Sanabria E, Vlaeminck SE, Boon N, Microbial Biotechnology 9, 389 (2016). http://doi.org/10.1111/1751-7915.12354
Abstract: Vegetables and fruits are an important part of a healthy food diet, however, the eco-sustainability of the production of these can still be significantly improved. European farmers and consumers spend an estimated Euro15.5 billion per year on inorganic fertilizers and the production of N-fertilizers results in a high carbon footprint. We investigated if fertilizer type and medium constituents determine microbial nitrogen conversions in organic growing media and can be used as a next step towards a more sustainable horticulture. We demonstrated that growing media constituents showed differences in urea hydrolysis, ammonia and nitrite oxidation and in carbon dioxide respiration rate. Interestingly, mixing of the growing media constituents resulted in a stimulation of the function of the microorganisms. The use of organic fertilizer resulted in an increase in amoA gene copy number by factor 100 compared to inorganic fertilizers. Our results support our hypothesis that the activity of the functional microbial community with respect to nitrogen turnover in an organic growing medium can be improved by selecting and mixing the appropriate growing media components with each other. These findings contribute to the understanding of the functional microbial community in growing media and its potential role towards a more responsible horticulture.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1111/1751-7915.12354
|
|
|
“Fertilizer type influences dynamics of the microbial community structure in the rhizosphere of tomato and impact the nutrient turnover and plant performance”. Grunert O, Robles Aguilar AA, Hernandez-Sanabria E, Reheul D, Vlaeminck SE, Boon N, Jablonowski ND, Communications in agricultural and applied biological sciences 81, 67 (2016)
Abstract: Ammonia-oxidizing microorganisms (AOB and AOA) and nitrite oxidizing bacteria (NOB) are the most important organisms responsible for ammonia and nitrite oxidation in agricultural ecosystems and growing media. Ammonia and nitrite oxidation are critical steps in the soil nitrogen cycle and can be affected by the application of mineral fertilizers or organic fertilizers. The functionality of the microbial community has a major impact on the nutrient turnover and will finally influence plant performance. The microbial community associated with the growing medium and its functionality will also be influenced by the rhizosphere and the bulk soil. In our study, we used a tomato plant with a high root exudation capacity in order to stimulate microbial activity. We studied plant performance in rhizotrons (a phentotyping system for imaging roots), including an optical method (planar optodes) for non-invasive, quantitative and high-resolution imaging of pH dynamics in the rhizosphere and adjacent medium. The horticultural growing medium was supplemented with organic-derived nitrogen or ammonium derived from struvite. The possible differences in the root structure between treatments is compared with the total root length. Destructive growing medium sampling and high throughput sequencing analysis of the bacterial abundance of the communities present in the rhizosphere and the bulk soil is used to study the growing medium-associated microbial community structure and functionality, and this will be related to pH changes in the rhizosphere and the bulk soil. Our hypothesis is that the growing medium-associated microbial community structure changes depending on the nitrogen form provided and we expect a higher abundance of bacteria in the treatment with organic fertilizer and a higher abundance of AOB and NOB in the rhizosphere in comparison to the bulk soil.
Keywords: A2 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
“Struvite and organic fertilizer impacting the rhizosphere microbial community, nutrient turnover and plant growth performance”. Grunert O, Robles Aguilar AA, Hernandez-Sanabria E, Vandekerckhove T, Reheul D, Van Labeke M-C, Vlaeminck S, Boon N, Jablonowski ND, , 12 p.
T2 (2016)
Keywords: P3 Proceeding; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
“Tomato plants rather than fertilizers drive microbial community structure in horticultural growing media”. Grunert O, Robles-Aguilar AA, Hernandez-Sanabria E, Schrey SD, Reheul D, Van Labeke M-C, Vlaeminck SE, Vanderkerckhove TGL, Mysara M, Monsieurs P, Temperton VM, Boon N, Jablonowski ND, Scientific reports 9, 9561 (2019). http://doi.org/10.1038/S41598-019-45290-0
Abstract: Synthetic fertilizer production is associated with a high environmental footprint, as compounds typically dissolve rapidly leaching emissions to the atmosphere or surface waters. We tested two recovered nutrients with slower release patterns, as promising alternatives for synthetic fertilizers: struvite and a commercially available organic fertilizer. Using these fertilizers as nitrogen source, we conducted a rhizotron experiment to test their effect on plant performance and nutrient recovery in juvenile tomato plants. Plant performance was significantly improved when organic fertilizer was provided, promoting higher shoot biomass. Since the microbial community influences plant nitrogen availability, we characterized the root-associated microbial community structure and functionality. Analyses revealed distinct root microbial community structure when different fertilizers were supplied. However, plant presence significantly increased the similarity of the microbial community over time, regardless of fertilization. Additionally, the presence of the plant significantly reduced the potential ammonia oxidation rates, implying a possible role of the rhizosheath microbiome or nitrification inhibition by the plant. Our results indicate that nitrifying community members are impacted by the type of fertilizer used, while tomato plants influenced the potential ammonia-oxidizing activity of nitrogen-related rhizospheric microbial communities. These novel insights on interactions between recovered fertilizers, plant and associated microbes can contribute to develop sustainable crop production systems.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1038/S41598-019-45290-0
|
|
|
“Hydrogen clathrates : next generation hydrogen storage materials”. Gupta A, Baron GV, Perreault P, Lenaerts S, Ciocarlan R-G, Cool P, Mileo PGM, Rogge S, Van Speybroeck V, Watson G, Van Der Voort P, Houlleberghs M, Breynaert E, Martens J, Denayer JFM, Energy Storage Materials 41, 69 (2021). http://doi.org/10.1016/J.ENSM.2021.05.044
Abstract: Extensive research has been carried on the molecular adsorption in high surface area materials such as carbonaceous materials and MOFs as well as atomic bonded hydrogen in metals and alloys. Clathrates stand among the ones to be recently suggested for hydrogen storage. Although, the simulations predict lower capacity than the expected by the DOE norms, the additional benefits of clathrates such as low production and operational cost, fully reversible reaction, environmentally benign nature, low risk of flammability make them one of the most promising materials to be explored in the next decade. The inherent ability to tailor the properties of clathrates using techniques such as addition of promoter molecules, use of porous supports and formation of novel reverse micelles morphology provide immense scope customisation and growth. As rapidly evolving materials, clathrates promise to get as close as possible in the search of “holy grail” of hydrogen storage. This review aims to provide the audience with the background of the current developments in the solid-state hydrogen storage materials, with a special focus on the hydrogen clathrates. The in-depth analysis of the hydrogen clathrates will be provided beginning from their discovery, various additives utilised to enhance their thermodynamic and kinetic properties, challenges in the characterisation of hydrogen in clathrates, theoretical developments to justify the experimental findings and the upscaling opportunities presented by this system. The review will present state of the art in the field and also provide a global picture for the path forward.
Keywords: A1 Journal article; Engineering sciences. Technology; Laboratory of adsorption and catalysis (LADCA); Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.ENSM.2021.05.044
|
|
|
“Self-inhibition can limit biologically enhanced TCE dissolution from a TCE DNAPL”. Haest PJ, Springael D, Seuntjens P, Smolders E, Chemosphere 89, 1369 (2012). http://doi.org/10.1016/J.CHEMOSPHERE.2012.05.097
Abstract: Biodegradation of trichloroethene (TCE) near a Dense Non Aqueous Phase Liquid (DNAPL) can enhance the dissolution rate of the DNAPL by increasing the concentration gradient at the DNAPL-water interface. Two-dimensional flow-through sand boxes containing a ICE DNAPL and inoculated with a TCE dechlorinating consortium were set up to measure this bio-enhanced dissolution under anaerobic conditions. The total mass of TCE and daughter products in the effluent of the biotic boxes was 3-6 fold larger than in the effluent of the abiotic box. However, the mass of daughter products only accounted for 19-55% of the total mass of chlorinated compounds in the effluent, suggesting that bio-enhanced dissolution factors were maximally 1.3-2.2. The enhanced dissolution most likely primarily resulted from variable DNAPL distribution rather than biodegradation. Specific dechlorination rates previously determined in a stirred liquid medium were used in a reactive transport model to identify the rate limiting factors. The model adequately simulated the overall TCE degradation when predicted resident microbial numbers approached observed values and indicated an enhancement factor for TCE dissolution of 1.01. The model shows that dechlorination of TCE in the 20 box was limited due to the short residence time and the self-inhibition of the TCE degradation. A parameter sensitivity analysis predicts that the bio-enhanced dissolution factor for this TCE source zone can only exceed a value of 2 if the TCE self-inhibition is drastically reduced (when a TCE tolerant dehalogenating community is present) or if the DNAPL is located in a low-permeable layer with a small Darcy velocity. (C) 2012 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.CHEMOSPHERE.2012.05.097
|
|
|
“Free ammonia and/or temperature impact study on temperature-acclimated mainstream nitrification sludge”. Han M, De Clippeleir H, Al-Omari A, Vlaeminck SE, Wett B, Murthy S, , 3 p.
T2 (2016)
Keywords: P3 Proceeding; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
“Impact of carbon to nitrogen ratio and aeration regime on mainstream deammonification”. Han M, De Clippeleir H, Al-Omari A, Wett B, Vlaeminck SE, Bott C, Murthy S, Water science and technology 74, 375 (2016). http://doi.org/10.2166/WST.2016.202
Abstract: While deammonification of high-strength wastewater in the sludge line of sewage treatment plants has become well established, the potential cost savings spur the development of this technology for mainstream applications. This study aimed at identifying the effect of aeration and organic carbon on the deammonification process. Two 10 L sequencing bath reactors with different aeration frequencies were operated at 25 degrees C. Real wastewater effluents from chemically enhanced primary treatment and high-rate activated sludge process were fed into the reactors with biodegradable chemical oxygen demand/nitrogen (bCOD/N) of 2.0 and 0.6, respectively. It was found that shorter aerobic solids retention time (SRT) and higher aeration frequency gave more advantages for aerobic ammonium-oxidizing bacteria (AerAOB) than nitrite oxidizing bacteria (NOB) in the system. From the kinetics study, it is shown that the affinity for oxygen is higher for NOB than for AerAOB, and higher dissolved oxygen set-point could decrease the affinity of both AerAOB and NOB communities. After 514 days of operation, it was concluded that lower organic carbon levels enhanced the activity of anoxic ammonium-oxidizing bacteria (AnAOB) over denitrifiers. As a result, the contribution of AnAOB to nitrogen removal increased from 40 to 70%. Overall, a reasonably good total removal efficiency of 66% was reached under a low bCOD/N ratio of 2.0 after adaptation.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.2166/WST.2016.202
|
|
|
“Water and process parameters as controllers for the ammonia to nitrite oxidation rate ratio in activated sludge”. Han M, Seuntjens D, Al-Omari A, Takacs I, Meerburg F, Murthy S, Vlaeminck SE, De Clippeleir H, , 3 p.
T2 (2017)
Keywords: P3 Proceeding; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
“Uncoupling the solids retention times of flocs and granules in mainstream deammonification : a screen as effective out-selection tool for nitrite oxidizing bacteria”. Han M, Vlaeminck SE, Al-Omari A, Wett B, Bott C, Murthy S, De Clippeleir H, Bioresource technology 221, 195 (2016). http://doi.org/10.1016/J.BIORTECH.2016.08.115
Abstract: This study focused on a physical separator in the form of a screen to out-select nitrite oxidizing bacteria (NOB) for mainstream sewage treatment. This separation relied on the principle that the NOB prefer to grow in flocs, while anammox bacteria (AnAOB) reside in granules. Two types of screens (vacuum and vibrating) were tested for separating these fractions. The vibrating screen was preferred due to more moderate normal forces and additional tangential forces, better balancing retention efficiency of AnAOB granules (41% of the AnAOB activity) and washout of NOB (92% activity washout). This operation resulted in increased NOB out-selection (AerAOB/NOB ratio of 2.3) and a total nitrogen removal efficiency of 70% at influent COD/N ratio of 1.4. An effluent total nitrogen concentration <10 mg N/L was achieved using this novel approach combining biological selection with physical separation, opening up the path towards energy positive sewage treatment. (C) 2016 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.BIORTECH.2016.08.115
|
|
|
Hauchecorne B (2011) Development of an FTIR in situ reactor for real time study of surface reactions in photocatalysis. 155 p
Keywords: Doctoral thesis; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
“Unravelling the mysteries of gas phase photocatalytic reaction pathways by studying the catalyst surface : a literature review of different Fourier transform infrared spectroscopic reaction cells used in the field”. Hauchecorne B, Lenaerts S, Journal of photochemistry and photobiology: C: photochemistry reviews 14, 72 (2013). http://doi.org/10.1016/J.JPHOTOCHEMREV.2012.09.003
Abstract: Unlike the profound knowledge of the reaction mechanisms occurring in water phase photocatalysis, still fairly little is known on the reaction mechanisms occurring on the catalyst surface when dealing with gaseous pollutants. Unfortunately, there are some differences between both reactions. For one, there are no abundant hydroxyl radicals present in the gas phase, so that possibly other species prove to be important in abating the pollutant. In order to unravel the mysteries of gas phase photocatalytic reaction pathways, in situ techniques must be used to allow the detection and identification of reaction intermediates on a working catalyst. Several techniques were already used in the past, of which Fourier transform infrared spectroscopy seems to be the most versatile. This review will therefore give a selective overview of different spectroscopic reaction cells constructed for the in situ study of photocatalytic gas phase reactions.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 12.317
Times cited: 8
DOI: 10.1016/J.JPHOTOCHEMREV.2012.09.003
|
|
|
“Elucidating the photocatalytic degradation pathway of acetaldehyde : an FTIR in situ study under atmospheric conditions”. Hauchecorne B, Terrens D, Verbruggen S, Martens JA, van Langenhove H, Demeestere K, Lenaerts S, Applied catalysis : B : environmental 106, 630 (2011). http://doi.org/10.1016/J.APCATB.2011.06.026
Abstract: In this paper, new insights of the photocatalytic oxidation pathway of acetaldehyde are obtained by means of an in-house constructed FTIR in situ reactor. It is shown that there are generally three different intermediates present: acetic acid, formic acid and formaldehyde. By means of FTIR in situ spectroscopy, this study revealed that these intermediates are bound on the TiO2 surface in different ways, resulting in the presence of more intermediate species, such as molecularly adsorbed acetic acid, bidentate acetate, molecularly adsorbed formic acid, monodentate formate, bidentate formate, formaldehyde and dioxymethylene. Furthermore, spectroscopic evidence is obtained concerning the formation of 3-hydroxybutanal and crotonaldehyde upon adsorption of acetaldehyde on TiO2 prior to UV illumination. The presented results thus give new insights in the photocatalytic oxidation pathway of acetaldehyde.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 9.446
Times cited: 46
DOI: 10.1016/J.APCATB.2011.06.026
|
|
|
Hauchecorne B, Tytgat T, Terrens D, Vanpachtenbeke F, Lenaerts S (2011) Reaction chamber for studying a solid-gas interaction : PCT/EP2011/051075
Keywords: Patent; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
“Validation of a newly developed FTIR in situ reactor: real time study of photocatalytic degradation of nitric oxide”. Hauchecorne B, Tytgat T, Terrens D, Vanpachtenbeke F, Lenaerts S, Infrared physics and technology 53, 469 (2010). http://doi.org/10.1016/J.INFRARED.2010.09.008
Abstract: For many years, photocatalysis has been proposed as one of the promising techniques to abate environmental pollutants. To improve these reactions it is vital to know the reaction mechanisms of the photocatalytic degradation. This new reactor will make it possible to study the catalytic surface at the moment the reactions occur. By the means of UV LED illumination there is no need of an external UV lamp and thus lowers the cost. The validation of this newly developed reactor is done by investigating the photocatalytic reaction mechanism of nitric oxide (NO) and comparing these findings with those already discussed in literature. From these results, it became clear that the newly developed FTIR in situ reactor allows real time study of photocatalytic degradations.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 1.713
Times cited: 12
DOI: 10.1016/J.INFRARED.2010.09.008
|
|
|
“Photocatalytic degradation of ethylene : an FTIR in situ study under atmospheric conditions”. Hauchecorne B, Tytgat T, Verbruggen SW, Hauchecorne D, Terrens D, Smits M, Vinken K, Lenaerts S, Applied catalysis : B : environmental 105, 111 (2011). http://doi.org/10.1016/J.APCATB.2011.03.041
Abstract: In this paper, the reaction mechanism of the photocatalytic oxidation of ethylene is elucidated by means of an in-house developed FTIR in situ reactor. This reactor allowed us to look at the catalytic surface at the moment the reactions actually occur. This new approach gave some exciting new insights in how ethylene is photocatalytically oxidised. It was found that there is a change in dipole moment of the ethylene molecule when it is brought in the neighbourhood of the catalyst. From this finding, a hypothesis was formulated on how the CC-bond from ethylene will break. It was found that the aforementioned interaction between the catalyst and the molecule, allows the excited electrons from the UV irradiated catalyst to occupy the lowest unoccupied molecular orbital (LUMO) of the ethylene molecule through a process known as backdonation. Following this hypothesis, it was found that the degradation occurs through the formation of two intermediates: formaldehyde and formic acid, for which formaldehyde is bound in two different ways (coordinatively and as bidentate). Finally CO2 and H2O are found as end products, resulting in the complete mineralisation of the pollutant.
Keywords: A1 Journal article; Engineering sciences. Technology; Molecular Spectroscopy (MolSpec); Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 9.446
Times cited: 29
DOI: 10.1016/J.APCATB.2011.03.041
|
|
|
“Impact of urban street canyon architecture on local atmospheric pollutant levels and magneto-chemical PM10 composition : an experimental study in Antwerp, Belgium”. Hofman J, Castanheiro A, Nuyts G, Joosen S, Spassov S, Blust R, De Wael K, Lenaerts S, Samson R, The science of the total environment 712, 135534 (2019). http://doi.org/10.1016/J.SCITOTENV.2019.135534
Abstract: As real-life experimental data on natural ventilation of atmospheric pollution levels in urban street canyons is still scarce and has proven to be complex, this study, experimentally evaluated the impact of an urban street canyon opening on local atmospheric pollution levels, during a 2-week field campaign in a typical urban street canyon in Antwerp, Belgium. Besides following up on atmospheric particulate matter (PM), ultrafine particles (UFPs) and black carbon (BC) levels, the magneto-chemical PM10 composition was quantified to identify contributions of specific elements in enclosed versus open street canyon sections. Results indicated no higher overall PM, UFP and BC concentrations at the enclosed site compared to the open site, but significant day-to-day variability between both monitoring locations, depending on the experienced wind conditions. On days with oblique wind regimes (4 out of 14), natural ventilation was observed at the open location while higher element contributions of Ca, Fe, Co, Ni, Cu, Zn and Sr were exhibited at the enclosed location. Magnetic properties correlated with the PM10 filter loading, and elemental content of Fe, Cr, Mn and Ti. Magnetic bivariate ratios identified finel-grained magnetite carriers with grain sizes below 0.1 μm, indicating similar magnetic source contributions at both monitoring locations. Our holistic approach, combining atmospheric monitoring with magneto-chemical PM characterization has shown the complex impact of real-life wind flow regimes, different source contributions and local traffic dynamics on the resulting pollutant concentrations and contribute to a better understanding on the urban ventilation processes of atmospheric pollution.
Keywords: A1 Journal article; Engineering sciences. Technology; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 4.9
DOI: 10.1016/J.SCITOTENV.2019.135534
|
|
|
“Cyclist exposure to black carbon, ultrafine particles and heavy metals : an experimental study along two commuting routes near Antwerp, Belgium”. Hofman J, Samson R, Joosen S, Blust R, Lenaerts S, Environmental research 164, 530 (2018). http://doi.org/10.1016/J.ENVRES.2018.03.004
Abstract: Urban environments typically exhibit large atmospheric pollution variation, in both space and time. In contrast to traditional monitoring networks suffering from a limited spatial coverage, mobile platforms enable personalized high-resolution monitoring, providing valuable insights into personal atmospheric pollution exposure, and the identification of potential pollution hotspots. This study evaluated personal cyclist exposure to UFPs, BC and heavy metals whilst commuting near Antwerp, Belgium, by performing mobile measurements with wearable black carbon (BC) and ultrafine particle (UFP) instruments. Loaded micro-aethalometer filterstrips were chemically analysed and the inhaled pollutant dose determined from the exhibited heart rate. Considerable spatial pollutant variation was observed along the travelled routes, with distinct contributions from spatial factors (e.g. traffic intersections, urban park and market) and temporary events. On average 300% higher BC, 20% higher UFP and changing elemental concentrations are observed along the road traffic route (RT), when compared to the bicycle highway route (BH). Although the overall background pollution determines a large portion of the experienced personal exposure (in this case 53% for BC and 40% for UFP), cyclists can influence their personal atmospheric pollution exposure, by selecting less exposed commuting routes. Our results, hereby, strengthen the body of evidence in favour of further policy investments in isolated bicycle infrastructure.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Times cited: 9
DOI: 10.1016/J.ENVRES.2018.03.004
|
|
|
“Effect of diclofenac on the production of volatile fatty acids from anaerobic fermentation of waste activated sludge”. Hu J, Zhao J, Wang D, Li X, Zhang D, Xu Q, Peng L, Yang Q, Zeng G, Bioresource technology 254, 7 (2018). http://doi.org/10.1016/J.BIORTECH.2018.01.059
Abstract: In this study, the impact of diclofenac (DCF), an antiinflammatory drug being extensively used in human health care and veterinary treatment, on the production of volatile fatty acids (VFAs) from anaerobic fermentation of waste activated sludge (WAS) was investigated for the first time. Experimental results showed that when DCF concentration increased from 2.5 to 25 mg/kg total suspended solid (TSS), the maximum production of VFAs increased from 599 to 1113 mg COD/L, but further increase of DCF to 47.5 mg/kg TSS decreased VFAs yield to 896 mg COD/L. The mechanism investigation revealed that DCF had no effect on the hydrolysis process, promoted the process of acidogenesis, acetogenesis, and homoacetogenesis, but severely inhibited methanogenesis, leading to the accumulation of VFAs. Microbial community analysis showed that the addition of DCF could promote the relative abundance of VFAs (especially acetic acid) producers, which was well consistent with the results obtained above.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.BIORTECH.2018.01.059
|
|
|
“Inequality measure of leaf area distribution for a drought-tolerant landscape plant”. Huang L, Ratkowsky DA, Hui C, Gielis J, Lian M, Shi P, Plants 12, 3143 (2023). http://doi.org/10.3390/PLANTS12173143
Abstract: Measuring the inequality of leaf area distribution per plant (ILAD) can provide a useful tool for quantifying the influences of intra- and interspecific competition, foraging behavior of herbivores, and environmental stress on plants’ above-ground architectural structures and survival strategies. Despite its importance, there has been limited research on this issue. This paper aims to fill this gap by comparing four inequality indices to measure ILAD, using indices for quantifying household income that are commonly used in economics, including the Gini index (which is based on the Lorenz curve), the coefficient of variation, the Theil index, and the mean log deviation index. We measured the area of all leaves for 240 individual plants of the species Shibataea chinensis Nakai, a drought-tolerant landscape plant found in southern China. A three-parameter performance equation was fitted to observations of the cumulative proportion of leaf area vs. the cumulative proportion of leaves per plant to calculate the Gini index for each individual specimen of S. chinensis. The performance equation was demonstrated to be valid in describing the rotated and right shifted Lorenz curve, given that >96% of root-mean-square error values were smaller than 0.004 for 240 individual plants. By examining the correlation between any of the six possible pairs of indices among the Gini index, the coefficient of variation, the Theil index, and the mean log deviation index, the data show that these indices are closely related and can be used interchangeably to quantify ILAD.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.3390/PLANTS12173143
|
|
|
“A superellipse with deformation and its application in describing the cross-sectional shapes of a square bamboo”. Huang W, Li Y, Niklas KJ, Gielis J, Ding Y, Cao L, Shi P, Symmetry-Basel 12, 2073 (2020). http://doi.org/10.3390/SYM12122073
Abstract: Many cross-sectional shapes of plants have been found to approximate a superellipse rather than an ellipse. Square bamboos, belonging to the genus Chimonobambusa (Poaceae), are a group of plants with round-edged square-like culm cross sections. The initial application of superellipses to model these culm cross sections has focused on Chimonobambusa quadrangularis (Franceschi) Makino. However, there is a need for large scale empirical data to confirm this hypothesis. In this study, approximately 750 cross sections from 30 culms of C. utilis were scanned to obtain cross-sectional boundary coordinates. A superellipse exhibits a centrosymmetry, but in nature the cross sections of culms usually deviate from a standard circle, ellipse, or superellipse because of the influences of the environment and terrain, resulting in different bending and torsion forces during growth. Thus, more natural cross-sectional shapes appear to have the form of a deformed superellipse. The superellipse equation with a deformation parameter (SEDP) was used to fit boundary data. We find that the cross-sectional shapes (including outer and inner rings) of C. utilis can be well described by SEDP. The adjusted root-mean-square error of SEDP is smaller than that of the superellipse equation without a deformation parameter. A major finding is that the cross-sectional shapes can be divided into two types of superellipse curves: hyperellipses and hypoellipses, even for cross sections from the same culm. There are two proportional relationships between ring area and the product of ring length and width for both the outer and inner rings. The proportionality coefficients are significantly different, as a consequence of the two different superellipse types (i.e., hyperellipses and hypoellipses). The difference in the proportionality coefficients between hyperellipses and hypoellipses for outer rings is greater than that for inner rings. This work informs our understanding and quantifying of the longitudinal deformation of plant stems for future studies to assess the influences of the environment on stem development. This work is also informative for understanding the deviation of natural shapes from a strict rotational symmetry.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 2.7
DOI: 10.3390/SYM12122073
|
|
|
“The scaling relationships of leaf biomass vs. leaf surface area of 12 bamboo species”. Huang W, Su X, Ratkowsky DA, Niklas KJ, Gielis J, Shi P, Global ecology and conservation 20, e00793 (2019). http://doi.org/10.1016/J.GECCO.2019.E00793
Abstract: There is convincing evidence for a scaling relationship between leaf dry weight (DW) and leaf surface area (A) for broad-leaved plants, and most estimates of the scaling exponent of DW vs. A are greater than unity. However, the scaling relationship of leaf fresh weight (FW) vs. A has been largely neglected. In the present study, we examined whether there is a statistically strong scaling relationship between FW and A and compared the goodness of fit to that of DW vs. A. Between 250 and 520 leaves from each of 12 bamboo species within 2 genera (Phyllostachys and Pleioblastus) were investigated. The reduced major axis regression protocols were used to determine scaling relationships. The fit for the linearized scaling relationship of FW vs. A was compared with that of DW vs. A using the coefficient of determination (i.e., r2). A stronger scaling relationship between FW and A than that between DW and A was observed for each of the 12 bamboo species investigated. Among the 12 species examined, five had significantly smaller scaling exponents of FW vs. A compared to those of DW vs. A; only one species had a scaling exponent of FW vs. A greater than that of DW vs. A. No significant difference between the two scaling exponents was observed for the remaining 6 species. Researchers conducting future studies might be well advised to consider the influence of leaf fresh weight when exploring the scaling relationships of foliar biomass allocation patterns.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.GECCO.2019.E00793
|
|
|
Huyskens C (2012) Fouling in submerged membrane bioreactors. 198 p
Keywords: Doctoral thesis; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
“A new method for the evaluation of the reversible and irreversible fouling propensity of MBR mixed liquor”. Huyskens C, Brauns E, van Hoof E, de Wever H, Journal of membrane science 323, 185 (2008). http://doi.org/10.1016/J.MEMSCI.2008.06.021
Abstract: In this paper, a new fouling measurement method is presented as a pragmatic approach to determine a mixed liquor's fouling propensity. The MBR-VFM (VITO Fouling Measurement) uses a specific measurement protocol consisting of alternating filtration and physical cleaning steps, which enables the calculation of both the reversible and the irreversible fouling resistances. The MBR-VFM principle, set-up and measurement protocol are described as well as the evaluation of the fouling measurement method. Finally, the MBR-VFM was validated by comparing the fouling propensity measured on-line by the MBR-VFM in a lab-scale MBR with the fouling of the MBR membranes themselves. Our experiments indicated that the MBR-VFM can accurately measure fouling and that it can even be detected earlier than can be seen from the on-line filtration data of the lab-scale system itself. Furthermore, the differences measured in reversible and irreversible fouling seemed to be related to the observed impact of physical and chemical cleaning respectively. Therefore, the application of the MBR-VFM as an on-line sensor in an advanced control system, enabling the deployment of the measured fouling data for the control of membrane cleaning, seems feasible and will be tested in the near future.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.MEMSCI.2008.06.021
|
|
|
“Validation of a supervisory control system for energy savings in membrane bioreactors”. Huyskens C, Brauns E, van Hoof E, Diels L, de Wever H, Water research 45, 1443 (2011). http://doi.org/10.1016/J.WATRES.2010.11.001
Abstract: The application of fixed operational protocols and settings for membrane bioreactors (MBR) often leads to suboptimal filtration conditions due to the dynamic nature of mixed liquor characteristics. With regard to process optimization and energy savings, the potential benefits of a dynamic control system, enabling to adapt fouling control actions (ACS outputs) in an automated way to the actual mixed liquor fouling propensity, are thus obvious. In this paper, the pilot-scale validation of such an advanced control system (ACS) is elaborated. A specific on-line fouling measurement method, the MBR-VFM (VITO Fouling Measurement), was used for the evaluation of the mixed liquors reversible fouling propensity, which was used as a primary ACS input parameter. A first series of tests with a gradual increase in complexity of the selected input and output parameters indicated the functionality of the ACS and demonstrated a substantial reduction of aeration, however sometimes at the expense of a higher fouling rate. The ACS was further fine-tuned and subsequently tested for a longer period under more dynamic operating conditions. A significant correlation was found between the reversible fouling potential measured by the MBR-VFM and the on-line permeability, indicating that the MBR-VFM is a suitable ACS input. Furthermore, an average 22% reduction in aeration flow to the membranes could be achieved without any obvious negative effect on filtration performance. This indicates that this approach is promising to optimize energy consumption in MBRs.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.WATRES.2010.11.001
|
|