Home | << 1 2 3 4 5 >> |
![]() |
Records | |||||
---|---|---|---|---|---|
Author | Snoeckx, R.; Heijkers, S.; Van Wesenbeeck, K.; Lenaerts, S.; Bogaerts, A. | ||||
Title | CO2conversion in a dielectric barrier discharge plasma: N2in the mix as a helping hand or problematic impurity? | Type | A1 Journal article | ||
Year | 2016 | Publication | Energy & environmental science | Abbreviated Journal | Energ Environ Sci |
Volume | 9 | Issue | 9 | Pages | 999-1011 |
Keywords | A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT); Sustainable Energy, Air and Water Technology (DuEL) | ||||
Abstract | Carbon dioxide conversion and utilization has gained significant interest over the years. A novel gas conversion technique with great potential in this area is plasma technology. A lot of research has already been performed, but mostly on pure gases. In reality, N2 will always be an important impurity in effluent gases. Therefore, we performed an extensive combined experimental and computational study on the effect of N2 in the range of 1–98% on CO2 splitting in dielectric barrier discharge (DBD) plasma. The presence of up to 50% N2 in the mixture barely influences the effective (or overall) CO2 conversion and energy efficiency, because the N2 metastable molecules enhance the absolute CO2 conversion, and this compensates for the lower CO2 fraction in the mixture. Higher N2 fractions, however, cause a drop in the CO2 conversion and energy efficiency. Moreover, in the entire CO2/N2 mixing ratio, several harmful compounds, i.e., N2O and NOx compounds, are produced in the range of several 100 ppm. The reaction pathways for the formation of these compounds are explained based on a kinetic analysis, which allows proposing solutions on how to prevent the formation of these harmful compounds. |
||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000372243600030 | Publication Date | 2015-12-15 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1754-5692 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 29.518 | Times cited | 68 | Open Access | |
Notes | The authors acknowledge financial support from the IAP/7 (Inter-university Attraction Pole) program ‘PSI-Physical Chemistry of Plasma-Surface Interactions’, financially supported by the Belgian Federal Office for Science Policy (BELSPO), as well as the Fund for Scientific Research Flanders (FWO). This work was carried out in part using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen, a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the University of Antwerp. | Approved ![]() |
Most recent IF: 29.518 | ||
Call Number | c:irua:133169 | Serial | 4020 | ||
Permanent link to this record | |||||
Author | Kertik, A.; Wee, L.H.; Pfannmöller, M.; Bals, S.; Martens, J.A.; Vankelecom, I.F.J. | ||||
Title | Highly selective gas separation membrane using in situ amorphised metal-organic frameworks | Type | A1 Journal article | ||
Year | 2017 | Publication | Energy & environmental science | Abbreviated Journal | Energ Environ Sci |
Volume | 10 | Issue | 10 | Pages | 2342-2351 |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | Conventional carbon dioxide (CO2) separation in the petrochemical industry via cryogenic distillation is energy intensive and environmentally unfriendly. Alternatively, polymer membrane-based separations are of significant interest owing to low production cost, low-energy consumption and ease of upscaling. However, the implementation of commercial polymeric membranes is limited by their permeability and selectivity trade-off and the insufficient thermal and chemical stability. Herein, a novel type of amorphous mixed matrix membrane (MMM) able to separate CO2/CH4 mixtures with the highest selectivities ever reported for MOF based MMMs is presented. The MMM consists of an amorphised metal-organic framework (MOF) dispersed in an oxidatively cross-linked matrix achieved by fine tuning of the thermal treatment temperature in air up to 350 degrees C which drastically boosts the separation properties of the MMM. Thanks to the protection of the surrounding polymer, full oxidation of this MOF (i.e. ZIF-8) is prevented, and amorphisation of the MOF is realized instead, thus in situ creating a molecular sieve network. In addition, the treatment also improves the filler-polymer adhesion and induces an oxidative cross-linking of the polyimide matrix, resulting in MMMs with increased stability or plasticization resistance at high pressure up to 40 bar, marking a new milestone as new molecular sieve MOF MMMs for challenging natural gas purification applications. A new field for the use of amorphised MOFs and a variety of separation opportunities for such MMMs are thus opened. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000414774500007 | Publication Date | 2017-08-09 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1754-5692; 1754-5706 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 29.518 | Times cited | 122 | Open Access | OpenAccess |
Notes | ; A.K. acknowledges financial support from the Erasmus-Mundus Doctorate in Membrane Engineering (EUDIME) Programme. L.H.W. thanks the FWO-Vlaanderen for a postdoctoral research fellowship (12M1415N). M. P. acknowledges financial support by the FP7 European project SUNFLOWER (FP7 #287594). S. B. acknowledges financial support from European Research Council (ERC Starting Grant # 335078-COLOURATOMS). J. A. M. gratefully acknowledges financial supports from the Flemish Government for long-term Methusalem funding. J. A. M. and I. F. J. V. acknowledge the Belgian Government for IAP-PAI networking. A. K. would also like to thank Frank Mathijs for the mechanical tests, Roy Bernstein for the XPS analysis and Lien Telen and Bart Goderis for the DSC measurements. We thank Verder Scientific Benelux for providing the service of ZIF-8 ball milling. ; ecas_sara | Approved ![]() |
Most recent IF: 29.518 | ||
Call Number | UA @ lucian @ c:irua:147399UA @ admin @ c:irua:147399 | Serial | 4879 | ||
Permanent link to this record | |||||
Author | Van Hoecke, L.; Laffineur, L.; Campe, R.; Perreault, P.; Verbruggen, S.W.; Lenaerts, S. | ||||
Title | Challenges in the use of hydrogen for maritime applications | Type | A1 Journal Article;Review article, Hydrogen Production, Hydrogen Storage, Maritime Applications | ||
Year | 2021 | Publication | Energy & Environmental Science | Abbreviated Journal | Energ Environ Sci |
Volume | Issue | Pages | |||
Keywords | A1 Journal Article;Review article, Hydrogen Production, Hydrogen Storage, Maritime Applications; Sustainable energy, air and water technology (DuEL) | ||||
Abstract | Maritime shipping is a key factor that enables the global economy, however the pressure it exerts on the environment is increasing rapidly. In order to reduce the emissions of harmful greenhouse gasses, the search is on for alternative fuels for the maritime shipping industry. In this work the usefulness of hydrogen and hydrogen carriers is being investigated as a fuel for sea going ships. Due to the low volumetric energy density of hydrogen under standard conditions, the need for efficient storage of this fuel is high. Key processes in the use of hydrogen are discussed, starting with the production of hydrogen from fossil and renewable sources. The focus of this review is different storage methods, and in this work we discuss the storage of hydrogen at high pressure, in liquefied form at cryogenic temperatures and bound to liquid or solid-state carriers. In this work a theoretical introduction to different hydrogen storage methods precedes an analysis of the energy-efficiency and practical storage density of the carriers. In the final section the major challenges and hurdles for the development of hydrogen storage for the maritime industry are discussed. The most likely challenges will be the development of a new bunkering infrastructure and suitable monitoring of the safety to ensure safe operation of these hydrogen carriers on board the ship. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000621101100009 | Publication Date | 2021-01-07 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1754-5692 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 29.518 | Times cited | Open Access | OpenAccess | |
Notes | For the completion of this work we would like to thank, Compagnie Maritime Belge for initial funding 9 of the research into maritime hydrogen storage and the University of Antwerp for funding of the 10 Doctoral Project that allowed for the completion of this work. | Approved ![]() |
Most recent IF: 29.518 | ||
Call Number | DuEL @ duel @c:irua:174754 | Serial | 6668 | ||
Permanent link to this record | |||||
Author | Rouwenhorst, K.H.R.; Jardali, F.; Bogaerts, A.; Lefferts, L. | ||||
Title | From the Birkeland–Eyde process towards energy-efficient plasma-based NOXsynthesis: a techno-economic analysis | Type | A1 Journal article | ||
Year | 2021 | Publication | Energy & Environmental Science | Abbreviated Journal | Energ Environ Sci |
Volume | 14 | Issue | 5 | Pages | 2520-2534 |
Keywords | A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | Plasma-based NO<sub>X</sub>synthesis<italic>via</italic>the Birkeland–Eyde process was one of the first industrial nitrogen fixation methods. However, this technology never played a dominant role for nitrogen fixation, due to the invention of the Haber–Bosch process. Recently, nitrogen fixation by plasma technology has gained significant interest again, due to the emergence of low cost, renewable electricity. We first present a short historical background of plasma-based NO<sub>X</sub>synthesis. Thereafter, we discuss the reported performance for plasma-based NO<sub>X</sub>synthesis in various types of plasma reactors, along with the current understanding regarding the reaction mechanisms in the plasma phase, as well as on a catalytic surface. Finally, we benchmark the plasma-based NO<sub>X</sub>synthesis process with the electrolysis-based Haber–Bosch process combined with the Ostwald process, in terms of the investment cost and energy consumption. This analysis shows that the energy consumption for NO<sub>X</sub>synthesis with plasma technology is almost competitive with the commercial process with its current best value of 2.4 MJ mol N<sup>−1</sup>, which is required to decrease further to about 0.7 MJ mol N<sup>−1</sup>in order to become fully competitive. This may be accomplished through further plasma reactor optimization and effective plasma–catalyst coupling. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000639255800001 | Publication Date | 2021-03-31 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1754-5692 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 29.518 | Times cited | Open Access | OpenAccess | |
Notes | H2020 European Research Council; Horizon 2020, 810182 ; Ministerie van Economische Zaken en Klimaat; This research was supported by the TKI-Energie from Toeslag voor Topconsortia voor Kennis en Innovatie (TKI) from the Ministry of Economic Affairs and Climate Policy, the Excellence of Science FWO-FNRS project (FWO grant ID GoF9618n, EOS ID 30505023), and the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (grant agreement No 810182 – SCOPE ERC Synergy project). | Approved ![]() |
Most recent IF: 29.518 | ||
Call Number | PLASMANT @ plasmant @c:irua:178173 | Serial | 6763 | ||
Permanent link to this record | |||||
Author | Lizin, S.; Van Passel, S.; De Schepper, E.; Maes, W.; Lutsen, L.; Manca, J.; Vanderzande, D. | ||||
Title | Life cycle analyses of organic photovoltaics : a review | Type | A1 Journal article | ||
Year | 2013 | Publication | Energy & Environmental Science | Abbreviated Journal | Energ Environ Sci |
Volume | 6 | Issue | 11 | Pages | 3136-3149 |
Keywords | A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM) | ||||
Abstract | This paper reviews the available life cycle analysis (LCA) literature on organic photovoltaics (OPVs). This branch of OPV research has focused on the environmental impact of single-junction bulk heterojunction polymer solar cells using a P3HT/PC60BM active layer blend processed on semi-industrial pilot lines in ambient surroundings. The environmental impact was found to be strongly decreasing through continuous innovation of the manufacturing procedures. The current top performing cell regarding environmental performance has a cumulative energy demand of 37.58 MJp m(-2) and an energy payback time in the order of months for cells having 2% efficiency, thereby rendering OPV cells one of the best performing PV technologies from an environmental point of view. Nevertheless, we find that LCA literature is lagging behind on the main body of OPV literature due to the lack of readily available input data. Still, LCA research has led us to believe that in the quest for higher efficiencies, environmental sustainability is being disregarded on the materials' side. Hence, we advise the scientific community to take the progress made on environmental sustainability aspects of OPV preparations into account not only because standard procedures put a bigger strain on the environment, but also because these methods may not be transferrable to an industrial process. Consequently, we recommend policy makers to subsidize research that bridges the gaps between fundamental materials research, stability, and scalability given that these constraints have to be fulfilled simultaneously if OPVs are ever to be successful on the market. Additionally, environmental sustainability will have to keep on being monitored to steer future developments in the right direction. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000325946400002 | Publication Date | 2013-10-11 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1754-5692; 1754-5706 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 29.518 | Times cited | 124 | Open Access | |
Notes | ; The authors are much obliged to both the INTERREG ORGAN-EXT project and FP7 MOLESOL project for their financial support, without which it would have been impossible to conduct this research. ; | Approved ![]() |
Most recent IF: 29.518; 2013 IF: 15.490 | ||
Call Number | UA @ admin @ c:irua:127548 | Serial | 6223 | ||
Permanent link to this record | |||||
Author | Maes, D.; Van Passel, S. | ||||
Title | Effective bioeconomy policies for the uptake of innovative technologies under resource constraints | Type | A1 Journal article | ||
Year | 2019 | Publication | Biomass & Bioenergy | Abbreviated Journal | Biomass Bioenerg |
Volume | 120 | Issue | 120 | Pages | 91-106 |
Keywords | A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM) | ||||
Abstract | The bioeconomy is a shared vision for a future European industry entirely based on organic matter. Authorities support this technological development with subsidies and policies stimulating R&D. One major limitation for the bioeconomy is that R&D and industrial growth require the continuous availability of biomass as a primary resource. This resource dependence is already present during the formative years of new biobased innovations and influences the pilot and demonstration phase of the development. Traditionally, it is assumed that public support for pilot and demonstration initiatives may overcome this hurdle. In this paper, we investigate how this resource constraint limits the effectiveness of bioeconomy policies. The future development of the biobased sector is simulated including the inherent dependence of industrial activity on biomass. We simulate the future growth and technological diversity of an emerging biotechnological sector: the sector of manure transformation in Belgium. The paper reports the evolutions for three policy scenarios. The model explicitly accounts for endogenous innovation and knowledge transfer mechanisms. The results show that policies may have an important impact on the sector structure in the long run, but the sector growth remains ultimately constrained by the availability of inputs. So bioeconomy policies to promote innovation will be less effective, unless mechanisms are included to alleviate the resource constraint. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000454887700011 | Publication Date | 2018-11-22 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0961-9534 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.219 | Times cited | 3 | Open Access | |
Notes | ; ; | Approved ![]() |
Most recent IF: 3.219 | ||
Call Number | UA @ admin @ c:irua:156757 | Serial | 6191 | ||
Permanent link to this record | |||||
Author | Witters, N.; Mendelsohn, R.; Van Passel, S.; Van Slycken, S.; Weyens, N.; Schreurs, E.; Meers, E.; Tack, F.; Vanheusden, B.; Vangronsveld, J. | ||||
Title | Phytoremediation, a sustainable remediation technology? 2 : economic assessment of CO2 abatement through the use of phytoremediation crops for renewable energy production | Type | A1 Journal article | ||
Year | 2012 | Publication | Biomass & Bioenergy | Abbreviated Journal | Biomass Bioenerg |
Volume | 39 | Issue | Pages | 470-477 | |
Keywords | A1 Journal article; Economics; Engineering Management (ENM) | ||||
Abstract | Phytoremediation could be a sustainable remediation alternative for conventional remediation technologies. However, its implementation on a commercial scale remains disappointing. To emphasize its sustainability, this paper examines whether and how the potential economic benefit of CO2 abatement for different crops used for phytoremediation or sustainable land management purposes could promote phytotechnologies. Our analysis is based on a case study in the Campine region, where agricultural soils are contaminated with mainly cadmium. We use Life Cycle Analysis to show for the most relevant crops (willow (Salix spp), energy maize (Zea mays), and rapeseed (Brassica napus)), that phytoremediation, used for renewable energy production, could abate CO2. Converting this in economic numbers through the Marginal Abatement Cost of CO2 ( 20 ton−1) we can integrate this in the economic analysis to compare phytoremediation crops among each other, and phytoremediation with conventional technologies. The external benefit of CO2 abatement when using phytoremediation crops for land management ranges between 55 and 501 per hectare. The purpose of these calculations is not to calculate a subsidy for phytoremediation. There is no reason why one would prefer phytoremediation crops for renewable energy production over normal biomass. Moreover, subsidies for renewable energy already exist. Therefore, we should not integrate these numbers in the economic analysis again. However, these numbers could contribute to making explicit the competitive advantage of phytoremediation compared to conventional remediation technologies, but also add to a more sustainably funded decision on which crop should be grown on contaminated land. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000302829900054 | Publication Date | 2011-12-20 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0961-9534 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.219 | Times cited | 38 | Open Access | |
Notes | ; ; | Approved ![]() |
Most recent IF: 3.219; 2012 IF: 2.975 | ||
Call Number | UA @ admin @ c:irua:129863 | Serial | 6236 | ||
Permanent link to this record | |||||
Author | Van Dael, M.; Van Passel, S.; Pelkmans, L.; Guisson, R.; Swinnen, G.; Schreurs, E. | ||||
Title | Determining potential locations for biomass valorization using a macro screening approach | Type | A1 Journal article | ||
Year | 2012 | Publication | Biomass & Bioenergy | Abbreviated Journal | Biomass Bioenerg |
Volume | 45 | Issue | Pages | 175-186 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM) | ||||
Abstract | European policy states that by 2020 at least 20% of final energy consumption should come from renewable energy sources. Biomass as a renewable energy source cannot be disregarded in order to attain this target. In this study a macro screening approach is developed to determine potential locations for biomass valorization in a specified region. The approach consists of five steps: (1) criteria determination, (2) data gathering, (3) weight assignment, (4) final score, (5) spatial representation. The resulting outcome provides a first well balanced scan of the possibilities for energy production using regional biomass. This way policy makers and investors can be supported and motivated to study the possibilities of building energy production plants at specific locations in more detail, which can be described as a 'micro-screening'. In our case study the approach is applied to determine the potentially interesting locations to establish a biomass project. The region has been limited to the forty-four communities in the province of Limburg (Belgium). The macro screening approach has shown to be very effective since the amount of interesting locations has been reduced drastically. (c) 2012 Elsevier Ltd. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000308384500019 | Publication Date | 2012-06-30 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0961-9534 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.219 | Times cited | 23 | Open Access | |
Notes | ; The authors gratefully acknowledge the financial support from INTERREG and the province of Limburg. Special thanks to our colleague Thomas Voets for his effort in making the GIS maps. Moreover, the authors would like to thank the two anonymous reviewers for their valuable comments. ; | Approved ![]() |
Most recent IF: 3.219; 2012 IF: 2.975 | ||
Call Number | UA @ admin @ c:irua:127554 | Serial | 6178 | ||
Permanent link to this record | |||||
Author | Bogaerts, A.; Centi, G. | ||||
Title | Plasma Technology for CO2 Conversion: A Personal Perspective on Prospects and Gaps | Type | A1 Journal article | ||
Year | 2020 | Publication | Frontiers in energy research | Abbreviated Journal | Front. Energy Res. |
Volume | 8 | Issue | Pages | ||
Keywords | A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | There is increasing interest in plasma technology for CO2 conversion because it can operate at mild conditions and it can store fluctuating renewable electricity into value-added compounds and renewable fuels. This perspective paper aims to provide a view on the future for non-specialists who want to understand the role of plasma technology in the new scenario for sustainable and low-carbon energy and chemistry. Thus, it is prepared to give a personal view on future opportunities and challenges. First, we introduce the current state-of-the-art and the potential of plasma-based CO2 conversion. Subsequently, we discuss the challenges to overcome the current limitations and to apply plasma technology on a large scale. The final section discusses the general context and the potential benefits of plasma-based CO2 conversion for our life and the impact on climate change. It also includes a brief analysis on the future scenario for energy and chemical production, and how plasma technology may realize new paths for CO2 utilization. |
||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000553392300001 | Publication Date | 2020-07-07 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 2296-598X | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.4 | Times cited | Open Access | OpenAccess | |
Notes | We acknowledge financial support from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation program (grant agreement no. 810182 – SCOPE ERC Synergy project). We thank A. Berthelot, M. Ramakers, R. Snoeckx, G. Trenchev, and V. Vermeiren for providing the figures used in this article. | Approved ![]() |
Most recent IF: 3.4; 2020 IF: NA | ||
Call Number | PLASMANT @ plasmant @c:irua:170136 | Serial | 6390 | ||
Permanent link to this record | |||||
Author | Callini, E.; Aguey-Zinsou, K.F.; Ahuja, R.; Ares, J.R.; Bals, S.; Biliškov, N.; Chakraborty, S.; Charalambopoulou, G.; Chaudhary, A.L.; Cuevas, F.; Dam, B.; de Jongh, P.; Dornheim, M.; Filinchuk, Y.; Grbović Novaković, J.; Hirscher, M.; Jensen, T.R.; Jensen, P.B.; Novaković, N.; Lai, Q.; Leardini, F.; Gattia, D.M.; Pasquini, L.; Steriotis, T.; Turner, S.; Vegge, T.; Züttel, A.; Montone, A. | ||||
Title | Nanostructured materials for solid-state hydrogen storage : a review of the achievement of COST Action MP1103 | Type | A1 Journal article | ||
Year | 2016 | Publication | International journal of hydrogen energy T2 – E-MRS Fall Meeting / Symposium C on Hydrogen Storage in Solids -, Materials, Systems and Aplication Trends, SEP 15-18, 2015, Warsaw, POLAND | Abbreviated Journal | Int J Hydrogen Energ |
Volume | 41 | Issue | 41 | Pages | 14404-14428 |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | In the framework of the European Cooperation in Science and Technology (COST) Action MP1103 Nanostructured Materials for Solid-State Hydrogen Storage were synthesized, characterized and modeled. This Action dealt with the state of the art of energy storage and set up a competitive and coordinated network capable to define new and unexplored ways for Solid State Hydrogen Storage by innovative and interdisciplinary research within the European Research Area. An important number of new compounds have been synthesized: metal hydrides, complex hydrides, metal halide ammines and amidoboranes. Tuning the structure from bulk to thin film, nanoparticles and nanoconfined composites improved the hydrogen sorption properties and opened the perspective to new technological applications. Direct imaging of the hydrogenation reactions and in situ measurements under operando conditions have been carried out in these studies. Computational screening methods allowed the prediction of suitable compounds for hydrogen storage and the modeling of the hydrogen sorption reactions on mono-, bi-, and three-dimensional systems. This manuscript presents a review of the main achievements of this Action. (C) 2016 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Pergamon-elsevier science ltd | Place of Publication | Oxford | Editor | |
Language | Wos | 000381950800051 | Publication Date | 2016-05-08 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0360-3199 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.582 | Times cited | 89 | Open Access | Not_Open_Access |
Notes | All the authors greatly thank the COST Action MP1103 for financial support. | Approved ![]() |
Most recent IF: 3.582 | ||
Call Number | UA @ lucian @ c:irua:135723 | Serial | 4307 | ||
Permanent link to this record | |||||
Author | Simon, Q.; Barreca, D.; Bekermann, D.; Gasparotto, A.; Maccato, C.; Comini, E.; Gombac, V.; Fornasiero, P.; Lebedev, O.I.; Turner, S.; Devi, A.; Fischer, R.A.; Van Tendeloo, G. | ||||
Title | Plasma-assisted synthesis of Ag/ZnO nanocomposites : first example of photo-induced H2 production and sensing | Type | A1 Journal article | ||
Year | 2011 | Publication | International journal of hydrogen energy | Abbreviated Journal | Int J Hydrogen Energ |
Volume | 36 | Issue | 24 | Pages | 15527-15537 |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | Ag/ZnO nanocomposites were developed by a plasma-assisted approach. The adopted strategy exploits the advantages of Plasma Enhanced-Chemical Vapor Deposition (PE-CVD) for the growth of columnar ZnO arrays on Si(100) and Al2O3 substrates, in synergy with the infiltration power of the Radio Frequency (RF)-sputtering technique for the subsequent dispersion of different amounts of Ag nanoparticles (NPs). The resulting composites, both as-prepared and after annealing in air, were thoroughly characterized with particular attention on their morphological organization, structure and composition. For the first time, the above systems have been used as catalysts in the production of hydrogen by photo-reforming of alcoholic solutions, yielding a stable H2 evolution even by the sole use of simulated solar radiation. In addition, Ag/ZnO nanocomposites presented an excellent response in the gas-phase detection of H2, opening attractive perspectives for advanced technological applications. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Oxford | Editor | ||
Language | Wos | 000297089700006 | Publication Date | 2011-10-14 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0360-3199; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.582 | Times cited | 62 | Open Access | |
Notes | Esteem 026019; Fwo | Approved ![]() |
Most recent IF: 3.582; 2011 IF: 4.054 | ||
Call Number | UA @ lucian @ c:irua:91901 | Serial | 2627 | ||
Permanent link to this record | |||||
Author | Snoeckx, R.; Setareh, M.; Aerts, R.; Simon, P.; Maghari, A.; Bogaerts, A. | ||||
Title | Influence of N2 concentration in a CH4/N2 dielectric barrier discharge used for CH4 conversion into H2 | Type | A1 Journal article | ||
Year | 2013 | Publication | International journal of hydrogen energy | Abbreviated Journal | Int J Hydrogen Energ |
Volume | 38 | Issue | 36 | Pages | 16098-16120 |
Keywords | A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | We present a combined study of experimental and computational work for a dielectric barrier discharge (DBD) used for CH4 conversion into H2. More specifically, we investigated the influence of N2 as an impurity (150,000 ppm) and as additive gas (199%) on the CH4 conversion and H2 yield. For this purpose, a zero-dimensional chemical kinetics model is applied to study the plasma chemistry. The calculated conversions and yields for various gas mixing ratios are compared to the obtained experimental values, and good agreement is achieved. The study reveals the significance of the View the MathML source and View the MathML source metastable states for the CH4 conversion into H2, based on a kinetic analysis of the reaction chemistry. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Oxford | Editor | ||
Language | Wos | 000327904500027 | Publication Date | 2013-10-23 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0360-3199; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.582 | Times cited | 40 | Open Access | |
Notes | Approved ![]() |
Most recent IF: 3.582; 2013 IF: 2.930 | |||
Call Number | UA @ lucian @ c:irua:111372 | Serial | 1642 | ||
Permanent link to this record | |||||
Author | Pasquini, L.; Sacchi, M.; Brighi, M.; Boelsma, C.; Bals, S.; Perkisas, T.; Dam, B. | ||||
Title | Hydride destabilization in core-shell nanoparticles | Type | A1 Journal article | ||
Year | 2014 | Publication | International journal of hydrogen energy | Abbreviated Journal | Int J Hydrogen Energ |
Volume | 39 | Issue | 5 | Pages | 2115-2123 |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | We present a model that describes the effect of elastic constraint on the thermodynamics of hydrogen absorption and desorption in biphasic core-shell nanoparticles, where the core is a hydride forming metal. In particular, the change of the hydride formation enthalpy and of the equilibrium pressure for the metal/hydride transformation are described as a function of nanoparticles radius, shell thickness, and elastic properties of both core and shell. To test the model, the hydrogen sorption isotherms of Mg-MgO core-shell nanoparticles, synthesized by inert gas condensation, were measured by means of optical hydrogenography. The model's predictions are in good agreement with the experimentally determined plateau pressure of hydrogen absorption. The features that a core-shell systems should exhibit in view of practical hydrogen storage applications are discussed with reference to the model and the experimental results. Copyright (C) 2013, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Oxford | Editor | ||
Language | Wos | 000331344800022 | Publication Date | 2014-01-04 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0360-3199; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.582 | Times cited | 32 | Open Access | Not_Open_Access |
Notes | COST Action MP1103 | Approved ![]() |
Most recent IF: 3.582; 2014 IF: 3.313 | ||
Call Number | UA @ lucian @ c:irua:115785 | Serial | 1528 | ||
Permanent link to this record | |||||
Author | Mooij, L.; Perkisas, T.; Palsson, G.; Schreuders, H.; Wolff, M.; Hjorvarsson, B.; Bals, S.; Dam, B. | ||||
Title | The effect of microstructure on the hydrogenation of Mg/Fe thin film multilayers | Type | A1 Journal article | ||
Year | 2014 | Publication | International journal of hydrogen energy | Abbreviated Journal | Int J Hydrogen Energ |
Volume | 39 | Issue | 30 | Pages | 17092-17103 |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | Nanoconfined magnesium hydride can be simultaneously protected and thermodynamically destabilized when interfaced with materials such as Ti and Fe. We study the hydrogenation of thin layers of Mg (<14 nm) nanoconfined in one dimension within thin film Fe/Mg/Fe/Pd multilayers by the optical technique Hydrogenography. The hydrogenation of nanosized magnesium layers in Fe/Mg/Fe multilayers surprisingly shows the presence of multiple plateau pressures, whose nature is thickness dependent. In contrast, hydrogen desorption occurs via a single plateau which does not depend on the Mg layer thickness. From structural and morphological analyses with X-ray diffraction/reflectometry and cross-section TEM, we find that the Mg layer roughness is large when deposited on Fe and furthermore contains high-angle grain boundaries (GB's). When grown on Ti, the Mg layer roughness is low and no high-angle GB's are detected. From a Ti/Mg/Fe multilayer, in which the Mg layer is flat and has little or no GB's, we conclude that MgH2 is indeed destabilized by the interface with Fe. In this case, both the ab- and desorption plateau pressures are increased by a factor two compared to the hydrogenation of Mg within Ti/Mg/Ti multilayers. We hypothesize that the GB's in the Fe/Mg/Fe multilayer act as diffusion pathways for Pd, which is known to greatly alter the hydrogenation behavior of Mg when the two materials share an interface. Copyright (C) 2014, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Oxford | Editor | ||
Language | Wos | 000343839000031 | Publication Date | 2014-09-10 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0360-3199; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.582 | Times cited | 15 | Open Access | Not_Open_Access |
Notes | COST Action MP1103 | Approved ![]() |
Most recent IF: 3.582; 2014 IF: 3.313 | ||
Call Number | UA @ lucian @ c:irua:121175 | Serial | 3575 | ||
Permanent link to this record | |||||
Author | Delmelle, R.; Amin-Ahmadi, B.; Sinnaeve, M.; Idrissi, H.; Pardoen, T.; Schryvers, D.; Proost, J. | ||||
Title | Effect of structural defects on the hydriding kinetics of nanocrystalline Pd thin films | Type | A1 Journal article | ||
Year | 2015 | Publication | International journal of hydrogen energy | Abbreviated Journal | Int J Hydrogen Energ |
Volume | 40 | Issue | 40 | Pages | 7335-7347 |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | While the microstructure of a metal is well-known to affect its equilibrium hydrogen uptake and therefore the hydriding thermodynamics, microstructural effects on the hydriding kinetics are much less documented. Moreover, for thin film systems, such microstructural effects are difficult to separate from the internal stress effect, since most defects generate internal stresses. Such a decoupling has been achieved in this paper for nanocrystalline Pd thin film model systems through the use of a high-resolution, in-situ curvature measurement set-up during Pd deposition, annealing and hydriding. This set-up allowed producing Pd thin films with similar internal stress levels but significantly different microstructures. This was evidenced from detailed defect statistics obtained by transmission electron microscopy, which showed that the densities of grain boundaries, dislocations and twin boundaries have all been lowered by annealing. The same set-up was then used to study the hydriding equilibrium and kinetic behaviour of the resulting films at room temperature. A full quantitative analysis of their hydriding cycles showed that the rate constants of both the adsorption- and absorption-limited kinetic regimes were strongly affected by microstructure. Defect engineering was thereby shown to increase the rate constants for hydrogen adsorption and absorption in Pd by a factor 40 and 30, respectively. Copyright (C) 2015, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Oxford | Editor | ||
Language | Wos | 000355884300012 | Publication Date | 2015-05-02 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0360-3199; | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.582 | Times cited | 13 | Open Access | |
Notes | Iap 7/21 | Approved ![]() |
Most recent IF: 3.582; 2015 IF: 3.313 | ||
Call Number | c:irua:126429 | Serial | 838 | ||
Permanent link to this record | |||||
Author | Rouwenhorst, K.H.R.; Jardali, F.; Bogaerts, A.; Lefferts, L. | ||||
Title | Correction: From the Birkeland–Eyde process towards energy-efficient plasma-based NOXsynthesis: a techno-economic analysis | Type | A1 Journal Article | ||
Year | 2023 | Publication | Energy & Environmental Science | Abbreviated Journal | Energy Environ. Sci. |
Volume | 16 | Issue | 12 | Pages | 6170-6173 |
Keywords | A1 Journal Article; Plasma, laser ablation and surface modeling Antwerp (PLASMANT) ; | ||||
Abstract | Correction for ‘From the Birkeland–Eyde process towards energy-efficient plasma-based NO<sub><italic>X</italic></sub>synthesis: a techno-economic analysis’ by Kevin H. R. Rouwenhorst<italic>et al.</italic>,<italic>Energy Environ. Sci.</italic>, 2021,<bold>14</bold>, 2520–2534, https://doi.org/10.1039/D0EE03763J. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | Publication Date | 2023-11-27 | ||
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1754-5692 | ISBN | Additional Links | ||
Impact Factor | 32.5 | Times cited | Open Access | ||
Notes | H2020 European Research Council; Horizon 2020, 810182 ; Ministerie van Economische Zaken en Klimaat; | Approved ![]() |
Most recent IF: 32.5; 2023 IF: 29.518 | ||
Call Number | PLASMANT @ plasmant @ | Serial | 8980 | ||
Permanent link to this record | |||||
Author | Osorio-Tejada, J.; Escriba-Gelonch, M.; Vertongen, R.; Bogaerts, A.; Hessel, V. | ||||
Title | CO₂ conversion to CO via plasma and electrolysis : a techno-economic and energy cost analysis | Type | A1 Journal article | ||
Year | 2024 | Publication | Energy & environmental science | Abbreviated Journal | |
Volume | Issue | Pages | |||
Keywords | A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) | ||||
Abstract | Electrification and carbon capture technologies are essential for achieving net-zero emissions in the chemical sector. A crucial strategy involves converting captured CO2 into CO, a valuable chemical feedstock. This study evaluates the feasibility of two innovative methods: plasma activation and electrolysis, using clean electricity and captured CO2. Specifically, it compares a gliding arc plasma reactor with an embedded novel carbon bed system to a modern zero-gap type low-temperature electrolyser. The plasma method stood out with an energy cost of 19.5 GJ per tonne CO, marking a 43% reduction compared to electrolysis and conventional methods. CO production costs for plasma- and electrolysis-based plants were $671 and $962 per tonne, respectively. However, due to high uncertainty regarding electrolyser costs, the CO production costs in electrolysis-based plants may actually range from $570 to $1392 per tonne. The carbon bed system in the plasma method was a key factor in facilitating additional CO generation from O-2 and enhancing CO2 conversion, contributing to its cost-effectiveness. Challenges for electrolysis included high costs of equipment and low current densities. Addressing these limitations could significantly decrease production costs, but challenges arise from the mutual relationship between intrinsic parameters, such as CO2 conversion, CO2 input flow, or energy cost. In a future scenario with affordable feedstocks and equipment, costs could drop below $500 per tonne for both methods. While this may be more challenging for electrolysis due to complexity and expensive catalysts, plasma-based CO production appears more viable and competitive. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 001218045900001 | Publication Date | 2024-05-06 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1754-5692; 1754-5706 | ISBN | Additional Links | UA library record; WoS full record | |
Impact Factor | 32.5 | Times cited | Open Access | ||
Notes | Approved ![]() |
Most recent IF: 32.5; 2024 IF: 29.518 | |||
Call Number | UA @ admin @ c:irua:205986 | Serial | 9138 | ||
Permanent link to this record | |||||
Author | Maes, D.; Van Passel, S. | ||||
Title | Interference of regional support policies on the economic and environmental performance of a hybrid cogeneration-solar panel energy system | Type | A1 Journal article | ||
Year | 2012 | Publication | Energy Policy | Abbreviated Journal | Energ Policy |
Volume | 42 | Issue | Pages | 670-680 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM) | ||||
Abstract | This paper assesses unintentional interference between different public policies promoting energy efficiency and renewable energy. The paper develops a methodology to study the interference by analysing the economic and technical behaviour of a hybrid energy system. The hybrid energy system in this case consists of an existing cogeneration unit extended with a new installation of thermal solar panels. This puts two complementary heating technologies in juxtaposition. The two technologies are supported with distinct regional support instruments in each region. The design and operation of the energy system is optimised from the point of view of the investor according to the different support instruments. The optimal configuration is analysed as well as its effect on reduced CO2-emissions during the lifetime of the project. The methodology is applied to a case-study for two neighbouring regions, the Netherlands and Flanders. The policies in the Netherlands show a beneficial synergy. In Flanders, the hybrid energy system is not interesting, indicating unbalanced high support for cogeneration in this case. From the point of view of the authorities, a more balanced regional policy as in the Netherlands provides a larger CO2-emission reduction for a smaller cost. (C) 2012 Elsevier Ltd. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000301616000066 | Publication Date | 2012-01-14 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0301-4215; 1873-6777 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.14 | Times cited | 4 | Open Access | |
Notes | ; The authors would especially like to thank Davy Duelen for the excellent case-study and data collection that enabled the present paper. The help and information provided by Pierre Gijsen also made the detailed assessment possible. We are also indebted to two anonymous reviewers, whose remarks strongly improved the paper. This project has been financed by the Impulse-project of the tUL (transnational University Limburg). ; | Approved ![]() |
Most recent IF: 4.14; 2012 IF: 2.743 | ||
Call Number | UA @ admin @ c:irua:127558 | Serial | 6220 | ||
Permanent link to this record | |||||
Author | Vanschoenwinkel, J.; Lizin, S.; Swinnen, G.; Azadi, H.; Van Passel, S. | ||||
Title | Solar cooking in Senegalese villages : an application of best-worst scaling | Type | A1 Journal article | ||
Year | 2014 | Publication | Energy Policy | Abbreviated Journal | Energ Policy |
Volume | 67 | Issue | Pages | 447-458 | |
Keywords | A1 Journal article; Sociology; Engineering sciences. Technology; Engineering Management (ENM) | ||||
Abstract | Dissemination programs of nontraditional cookstoves often fail. Nontraditional cookstoves aim to solve problems associated with biomass fuel usage in developing countries. Recent studies do not explain what drives user's cookstove choice. This study therefore builds a holistic framework that centralizes product-specific preferences or needs. The case study identifies product-specific factors that influence rural Senegalese inhabitants to switch to solar cooking, using best worst scaling. Looking at the preferences, the case study classified 126 respondents, in three distinct market segments with different solar cooking expectations. The paper identifies socio-demographic characteristics that explain these differences in the respondents' preferences. Finally, the respondent sample is divided in two groups: solar cooker owners and non-owners. When studied with regard to the same issue, solar cooker owners appear to value benefits of the solar cooker lower than non-owners. This is due to program factors (such as formations, after-sales network) and miscommunication (such as a wrong image of the solar cooker) that highly influenced the respondents' cookstove choice. As a conclusion, solar cookers and solar cooking programs are not always adapted to the needs and requirements of the end-users. Needs-oriented and end-user adopted strategies are necessary in order to successfully implement nontraditional cookstoves programs. (C) 2013 Elsevier Ltd. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000332815300043 | Publication Date | 2014-01-08 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0301-4215; 1873-6777 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.14 | Times cited | 10 | Open Access | |
Notes | ; The authors thank the VLIR-UOS for their financial support and the Sol Suffit Program for their co-operation during the research. ; | Approved ![]() |
Most recent IF: 4.14; 2014 IF: 2.575 | ||
Call Number | UA @ admin @ c:irua:127544 | Serial | 6251 | ||
Permanent link to this record | |||||
Author | Van Dael, M.; Lizin, S.; Swinnen, G.; Van Passel, S. | ||||
Title | Young people's acceptance of bioenergy and the influence of attitude strength on information provision | Type | A1 Journal article | ||
Year | 2017 | Publication | Renewable Energy | Abbreviated Journal | Renew Energ |
Volume | 107 | Issue | Pages | 417-430 | |
Keywords | A1 Journal article; Economics; Engineering sciences. Technology; Engineering Management (ENM) | ||||
Abstract | This study investigated the effects of using a standardized PowerPoint lecture to provide young people with nuanced information about bioenergy. The studys aim was to understand the relationship between knowledge and participants perception of bioenergy, and the relationship of the latter to participants attitude strength and intention to use and learn about bioenergy. Data were collected from 715 participants using a survey instrument that contained mainly Likert-scale questions. Data were then processed using partial least squares structural equation modelling. Results show that providing such information increases knowledge about bioenergy, but does relatively little to create a more positive perception of bioenergy. In turn, having a more positive view about bioenergy would lead to a higher intention to use bioenergy. Attitude strength was found to mediate the previous relationship and decreases the strength of the relationship between perception and intention to use. Results also show that the lecture weakly contributed to building attitude strength, rendering opinion change less likely in the future. We conclude that listening to a lecture on bioenergy slightly improves peoples perception of bioenergy, makes it more likely that people maintain such a disposition, and translates into a slightly higher intention to use bioenergy. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000396946900036 | Publication Date | 2017-02-08 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0960-1481 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles; WoS full record; WoS citing articles | |
Impact Factor | 4.357 | Times cited | 10 | Open Access | |
Notes | ; This work was supported by the Research Foundation Flanders (FWO; grant number 12G5415N). The authors gratefully acknowledge Sara Leroi-Werelds (Hasselt University) for her valuable comments. ; | Approved ![]() |
Most recent IF: 4.357 | ||
Call Number | UA @ admin @ c:irua:140683 | Serial | 6280 | ||
Permanent link to this record | |||||
Author | De Schepper, E.; Van Passel, S.; Manca, J.; Thewys, T. | ||||
Title | Combining photovoltaics and sound barriers : a feasibility study | Type | A1 Journal article | ||
Year | 2012 | Publication | Renewable Energy | Abbreviated Journal | Renew Energ |
Volume | 46 | Issue | Pages | 297-303 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM) | ||||
Abstract | In the light of global warming, renewables such as solar photovoltaics (PV) are important to decrease greenhouse gas emissions. An important issue regarding implementation of solar panels on large scale, is the limited available area. Therefore, it can be interesting to combine PV with alternative applications, as a ways of not requiring “additional” space. One example is a photovoltaic noise barrier (PVNB), where a noise barrier located along a highway or railway is used as substructure for PV modules. Even though a PVNB is not a novel concept, the absence of economic assessments in literature can be a barrier to their wider implementation. In this paper, a feasibility study of a PVNB in Belgium is conducted, using a cost benefit analysis including a Monte Carlo sensitivity analysis. Besides purely economic aspects, also ecological benefits are monetized. The sensitivity analysis indicates that the ecological benefit of noise reduction, which is valuated using a noise sensitivity depreciation index applied to real estate prices, is of major importance in determining the net present value of the case study. On the contrary, the impact of reducing CO2 emissions seems to be negligible when expressed in monetary terms. The results suggest that the PVNB as a whole and also its separate components -.e. the PV array and the noise barrier can be profitable projects, when ecological benefits are included. (C) 2012 Elsevier Ltd. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000305169400036 | Publication Date | 2012-04-06 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0960-1481 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.357 | Times cited | 12 | Open Access | |
Notes | ; ; | Approved ![]() |
Most recent IF: 4.357; 2012 IF: 2.989 | ||
Call Number | UA @ admin @ c:irua:127555 | Serial | 6170 | ||
Permanent link to this record | |||||
Author | Lizin, S.; Leroy, J.; Delvenne, C.; Dijk, M.; De Schepper, E.; Van Passel, S. | ||||
Title | A patent landscape analysis for organic photovoltaic solar cells : identifying the technology's development phase | Type | A1 Journal article | ||
Year | 2013 | Publication | Renewable Energy | Abbreviated Journal | Renew Energ |
Volume | 57 | Issue | Pages | 5-11 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM) | ||||
Abstract | Organic photovoltaics (OPV) have developed into a vast research area. Progress in various directions has made it difficult to monitor the technology's precise development state. We offer a patent landscape analysis over all OPV devices, their substrates and encapsulation materials to provide an overview of patenting activity from a historical, organizational, geographical and technological point of view. Such an exercise is instrumental for private companies and research institutes aiming at both internal or external technology creation. We discuss our findings in the context of the Industrial Life Cycle model and find OPV still residing in the fluid technology development phase. Technology development is still following an exponential growth path, with the majority of patents coming from the Asian continent and in general private companies. For devices, the main technological focus can be traced back to the “H01L-031” international patent classification (IPC) main group. For the queried substrates, the most attention has gone to glass, but paper and textile have drawn significant interest too. Finally, encapsulation is found to be a less mature research field given the smaller number of patent families. The latter shows that the technology has not matured to the level where processing is carried out on a commercial scale. (C) 2013 Elsevier Ltd. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000319025000002 | Publication Date | 2013-02-13 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0960-1481 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.357 | Times cited | 18 | Open Access | |
Notes | ; The authors are much obliged to INTERREG for their financial support of the ORGANEXT project (www.organext.org), without which it would have been impossible to conduct this research. ; | Approved ![]() |
Most recent IF: 4.357; 2013 IF: 3.361 | ||
Call Number | UA @ admin @ c:irua:127551 | Serial | 6143 | ||
Permanent link to this record | |||||
Author | Nabavi-Pelesaraei, A.; Azadi, H.; Van Passel, S.; Saber, Z.; Hosseini-Fashami, F.; Mostashari-Rad, F.; Ghasemi-Mobtaker, H. | ||||
Title | Prospects of solar systems in production chain of sunflower oil using cold press method with concentrating energy and life cycle assessment | Type | A1 Journal article | ||
Year | 2021 | Publication | Energy | Abbreviated Journal | Energy |
Volume | 223 | Issue | Pages | 120117 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM) | ||||
Abstract | The aim of this study is determination of exergoenvironmental efficiency for using solar technologies in sunflower oil production in Iran. Accordingly, the applications of photovoltaic and photovoltaic/thermal systems were evaluated for both agricultural and industrial phases of sunflower oil production. Energy results reveal that 1 ton of sunflower oil consumes and produces about 180,354 and 39,400 MJ energy, respectively. About 86% of total energy consumption belongs to agricultural phase and electricity with 32%, has the highest share of total energy consumption. IMPACT 2002+ method and cumulative energy demand of life cycle assessment are applied to 3 defined scenarios including Present, photovoltaic and photovoltaic/thermal. Results indicate that total amounts of climate change in Present scenarios is 24537.53 kg CO2 eq.. The highest share of human health (90%), ecosystem quality (90%) and climate change (50%) in all scenarios belongs to direct emissions. Results also illustrates that total cumulative energy demand of Present, photovoltaic and photovoltaic/thermal scenarios are about 177,538, 99,054 and 132,158 MJ 1TSO(-1), respectively. Furthermore, the most contribution of non-renewable resources and fossil fuels belongs to electricity (37%), nitrogen (52%) and photovoltaic/thermal panels (39%) in Present, photovoltaic and photovoltaic/thermal scenarios, respectively. Finally the photovoltaic scenario is the best environmental-friendly scenario. (c) 2021 Elsevier Ltd. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000637964000003 | Publication Date | 2021-02-17 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0360-5442 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.52 | Times cited | Open Access | OpenAccess | |
Notes | Approved ![]() |
Most recent IF: 4.52 | |||
Call Number | UA @ admin @ c:irua:178193 | Serial | 6940 | ||
Permanent link to this record | |||||
Author | Quintero-Coronel, D.A.; Lenis-Rodas, Y.A.; Corredor, L.A.; Perreault, P.; Gonzalez-Quiroga, A. | ||||
Title | Thermochemical conversion of coal and biomass blends in a top-lit updraft fixed bed reactor : experimental assessment of the ignition front propagation velocity | Type | A1 Journal article | ||
Year | 2021 | Publication | Energy | Abbreviated Journal | Energy |
Volume | 220 | Issue | Pages | 119702-119710 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) | ||||
Abstract | Co-thermochemical conversion of coal and biomass can potentially decrease the use of fossil carbon and pollutant emissions. This work presents experimental results for the so-called top-lit updraft fixed bed reactor, in which the ignition front starts at the top and propagates downward while the gas product flows upwards. The study focuses on the ignition front propagation velocity for the co-thermochemical conversion of palm kernel shell and high-volatile bituminous coal. Within the range of assessed air superficial velocities, the process occurred under gasification and near stoichiometric conditions. Under gasification conditions increasing coal particle size from 7.1 to 22 mm decreased ignition front velocity by around 26% regardless of the coal volume percentage. Furthermore, increasing coal volume percentage and decreasing coal particle size result in product gas with higher energy content. For the operation near stoichiometric conditions, increasing coal volume percentage from 10 to 30% negatively affected the ignition front velocity directly proportional to its particle size. Additional experiments confirmed a linear dependence of ignition front velocity on air superficial velocity. Further steps in the development of the top-lit updraft technology are implementing continuous solids feeding and variable cross-sectional area and optimizing coal particle size distribution. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000623087300003 | Publication Date | 2020-12-24 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0360-5442 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.52 | Times cited | Open Access | OpenAccess | |
Notes | Approved ![]() |
Most recent IF: 4.52 | |||
Call Number | UA @ admin @ c:irua:175861 | Serial | 8664 | ||
Permanent link to this record | |||||
Author | Compernolle, T.; Witters, N.; Van Passel, S.; Thewys, T. | ||||
Title | Analyzing a self-managed CHP system for greenhouse cultivation as a profitable way to reduce CO2-emissions | Type | A1 Journal article | ||
Year | 2011 | Publication | Energy | Abbreviated Journal | Energy |
Volume | 36 | Issue | 4 | Pages | 1940-1947 |
Keywords | A1 Journal article; Engineering sciences. Technology | ||||
Abstract | To counter global warming, a transition to a low-carbon economy is needed. The greenhouse sector can contribute by installing Combined Heat and Power (CHP) systems, known for their excellent energy efficiency. Due to the recent European liberalization of the energy market, glass horticulturists have the opportunity to sell excess electricity to the market and by tailored policy and support measures, regional governments can fill the lack of technical and economic knowledge, causing initial resistance. This research investigates the economic and environmental opportunities using two detailed cases applying a self managed cogeneration system. The Net Present Value is calculated to investigate the economic feasibility. The Primary Energy Saving, the CO2 Emission Reduction indicator and an Emission Balance are applied to quantify the environmental impact. The results demonstrate that a self-managed CHP system is economic viable and that CO2 emissions are reduced. (C) 2010 Elsevier Ltd. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000289605900014 | Publication Date | 2010-04-03 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0360-5442 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.52 | Times cited | 19 | Open Access | |
Notes | ; ; | Approved ![]() |
Most recent IF: 4.52; 2011 IF: 3.487 | ||
Call Number | UA @ admin @ c:irua:127561 | Serial | 6152 | ||
Permanent link to this record | |||||
Author | Berdiyorov, G.R.; Madjet, M.E.; El-Mellouhi, F.; Peeters, F.M. | ||||
Title | Effect of crystal structure on the electronic transport properties of the organometallic perovskite CH3NH3PbI3 | Type | A1 Journal article | ||
Year | 2016 | Publication | Solar energy materials and solar cells T2 – 2nd International Renewable and Sustainable Energy Conference (IRSEC), OCT 17-19, 2014, Ouarzazate, MOROCCO | Abbreviated Journal | Sol Energ Mat Sol C |
Volume | 148 | Issue | 148 | Pages | 60-66 |
Keywords | A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT) | ||||
Abstract | Using density-functional theory in combination with the nonequilibrium Green's function formalism, we study the effect of the crystal lattice structure of organometallic perovskite CH3NH3PbI3 on its electronic transport properties. Both dispersive interactions and spin-orbit coupling are taken into account in describing structural and electronic properties of the system. We consider two different phases of the material, namely the orthorhombic and cubic lattice structures, which are energetically stable at low (< 160 K) and high (> 330 K) temperatures, respectively. The sizable geometrical differences between the two structures in term of lattice parameters, PbI6 octahedral tilts, rotation and deformations, have considerable impact on the transport properties of the material. For example, at zero bias and for all considered electron energies, the cubic phase has a larger transmission than the orthorhombic one, although both show similar electronic densities of states. Depending on the applied voltage, the current in the cubic system can be several orders of magnitude larger as compared to the one obtained for the orthorhombic sample. We attribute this enhancement in the transmission to the presence of extended states in the cubic phase due to the symmetrically shaped and ordered PbI6 octaherdra. (C) 2015 Elsevier B.V. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Elsevier science bv | Place of Publication | Amsterdam | Editor | |
Language | Wos | 000371944500011 | Publication Date | 2015-11-06 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0927-0248 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.784 | Times cited | 16 | Open Access | |
Notes | ; ; | Approved ![]() |
Most recent IF: 4.784 | ||
Call Number | UA @ lucian @ c:irua:133151 | Serial | 4163 | ||
Permanent link to this record | |||||
Author | Berdiyorov, G.R.; El-Mellouhi, F.; Madjet, M.E.; Alharbi, F.H.; Peeters, F.M.; Kais, S. | ||||
Title | Effect of halide-mixing on the electronic transport properties of organometallic perovskites | Type | A1 Journal article | ||
Year | 2016 | Publication | Solar energy materials and solar cells T2 – 2nd International Renewable and Sustainable Energy Conference (IRSEC), OCT 17-19, 2014, Ouarzazate, MOROCCO | Abbreviated Journal | Sol Energ Mat Sol C |
Volume | 148 | Issue | 148 | Pages | 2-10 |
Keywords | A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT) | ||||
Abstract | Using density-functional theory in combination with the nonequilibrium Green's function formalism, we study the effect of iodide/chloride and iodide/bromide mixing on the electronic transport in lead based organometallic perovskite CH3NH3PbI3, which is known to be an effective tool to tune the electronic and optical properties of such materials. We found that depending on the level and position of the halide mixing, the electronic transport can be increased by more than a factor of 4 for a given voltage biasing. The largest current is observed for small concentration of bromide substitutions located at the equatorial sites. However, full halide substitution has a negative effect on the transport properties of this material: the current drops by an order of magnitude for both CH3NH3PbCl3 and CH3NH3PbBr3 samples. (C) 2015 Elsevier B.V. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Elsevier science bv | Place of Publication | Amsterdam | Editor | |
Language | Wos | 000371944500002 | Publication Date | 2015-12-18 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0927-0248 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.784 | Times cited | 23 | Open Access | |
Notes | ; ; | Approved ![]() |
Most recent IF: 4.784 | ||
Call Number | UA @ lucian @ c:irua:133150 | Serial | 4165 | ||
Permanent link to this record | |||||
Author | Carraro, G.; Maccato, C.; Gasparotto, A.; Warwick, M.E.A.; Sada, C.; Turner, S.; Bazzo, A.; Andreu, T.; Pliekhova, O.; Korte, D.; Lavrenčič Štangar, U.; Van Tendeloo, G.; Morante, J.R.; Barreca, D. | ||||
Title | Hematite-based nanocomposites for light-activated applications: Synergistic role of TiO2 and Au introduction | Type | A1 Journal article | ||
Year | 2017 | Publication | Solar energy materials and solar cells | Abbreviated Journal | Sol Energ Mat Sol C |
Volume | 159 | Issue | 159 | Pages | 456-466 |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | Photo-activated processes have been widely recognized as cost-effective and environmentally friendly routes for both renewable energy generation and purification/cleaning technologies. We report herein on a plasma- assisted approach for the synthesis of Fe 2 O 3 -TiO 2 nanosystems functionalized with Au nanoparticles. Fe 2 O 3 nanostructures were grown by plasma enhanced-chemical vapor deposition, followed by the sequential sputtering of titanium and gold under controlled conditions, and final annealing in air. The target nanosystems were subjected to a thorough multi-technique characterization, in order to elucidate the interrelations between their chemico-physical properties and the processing conditions. Finally, the functional performances were preliminarily investigated in both sunlight-assisted H 2 O splitting and photocatalytic activity tests in view of self- cleaning applications. The obtained results highlight the possibility of tailoring the system behaviour and candidate the present Fe 2 O 3 -TiO 2 -Au nanosystems as possible multi-functional low-cost platforms for light-activated processes. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000388053600053 | Publication Date | 2016-10-07 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0927-0248 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.784 | Times cited | 15 | Open Access | Not_Open_Access |
Notes | The research leading to these results has received funding from the FP7 project “SOLAROGENIX” (NMP4-SL-2012-310333), as well as from Padova University ex-60% 2013-2016 projects, grant no. CPDR132937/13 (SOLLEONE) and the post-doc fellowship ACTION. INFINITY project in the framework of the EU Erasmus Mundus Action 2 is also acknowledged to provide a Ph.D. financial support as well as Slovenian Research Agency (program P2-0377). The authors are grateful to Dr. E. Toniato (Department of Chemistry, Padova University, Italy) for synthetic assistance and to Prof. E. Bontempi and Dr. M. Brisotto (Chemistry for Technologies Laboratory, Brescia University, Italy) for XRD analyses. | Approved ![]() |
Most recent IF: 4.784 | ||
Call Number | EMAT @ emat @ c:irua:135833 | Serial | 4284 | ||
Permanent link to this record | |||||
Author | D'Olieslaeger, L.; Pfannmöller, M.; Fron, E.; Cardinaletti, I.; Van der Auweraer, M.; Van Tendeloo, G.; Bals, S.; Maes, W.; Vanderzande, D.; Manca, J.; Ethirajan, A. | ||||
Title | Tuning of PCDTBT : PC71BM blend nanoparticles for eco-friendly processing of polymer solar cells | Type | A1 Journal article | ||
Year | 2017 | Publication | Solar energy materials and solar cells | Abbreviated Journal | Sol Energ Mat Sol C |
Volume | 159 | Issue | 159 | Pages | 179-188 |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | We report the controlled preparation of water processable nanoparticles (NPs) employing the push-pull polymer PCDTBT and the fullerene acceptor PC71BM in order to enable solar cell processing using eco-friendly solvent (i.e. water). The presented method provides the possibility to separate the formation of the active layer blend and the deposition of the active layer into two different processes. For the first time, the benefits of aqueous processability for the high-potential class of push-pull polymers, generally requiring high boiling solvents, are made accessible. With our method we demonstrate excellent control over the blend stoichiometry and efficient mixing. Furthermore, we provide visualization of the nano morphology of the different NPs to obtain structural information down to similar to 2 nm resolution using advanced analytical electron microscopy. The imaging directly reveals very small compositional demixing in the PCDTBT:PC71BM blend NPs, in the size range of about <5 nm, indicating fine mixing at the molecular level. The suitability of the proposed methodology and materials towards the aspects of eco-friendly processing of organic solar cells is demonstrated through a processing of lab scale NPs solar cell prototypes reaching a power conversion efficiency of 1.9%. (C) 2016 Elsevier B.V. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Amsterdam | Editor | ||
Language | Wos | 000388053600021 | Publication Date | 2016-09-19 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0927-0248 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.784 | Times cited | 32 | Open Access | OpenAccess |
Notes | ; This work was supported by BOF funding of Hasselt University, the Interreg project Organext, and the IAP 7/05 project FS2 (Functional Supramolecular Systems), granted by the Science Policy Office of the Belgian Federal Government (BELSPO). A.E. is a post-doctoral fellow of the Flanders Research Foundation (FWO). M.P. gratefully acknowledges the SIM NanoForce program for financial support. S.B. further acknowledges financial support from the European Research Council (ERC Starting Grant #335078-COLOURATOMS). The authors are thankful for technical support by J. Smits, T. Vangerven, and J. Baccus. ; ecas_sara | Approved ![]() |
Most recent IF: 4.784 | ||
Call Number | UA @ lucian @ c:irua:139157UA @ admin @ c:irua:139157 | Serial | 4450 | ||
Permanent link to this record | |||||
Author | Lizin, S.; Van Passel, S.; Vranken, L. | ||||
Title | Heterogeneity in the solar-powered consumer electronics market : a discrete choice experiments study | Type | A1 Journal article | ||
Year | 2016 | Publication | Solar Energy Materials And Solar Cells | Abbreviated Journal | Sol Energ Mat Sol C |
Volume | 156 | Issue | Pages | 140-146 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM) | ||||
Abstract | Solar-powered consumer electronics are a likely starting point for organic photovoltaic (OPV) market development. Therefore, a generic discrete choice experiments study can determine how Flemish consumers value solar-cell characteristics for solar-poweied consumer electronics. Such characteristics include efficiency, lifetime, aesthetics, integratability, and price. We contribute to the literature by investigating preference heterogeneity in a solar-power niche market with an experimental design with a fixed reference alternative. The error components random parameter logit (ECRPL) with interactions provides a better fit than the latent class (LC) model for our choice data. The main effects had the expected signs. Consequently, aesthetics and integratability are OPV's assets. Nevertheless, heterogeneity puts the results that are valid for the average consumer into perspective. Based on our findings, OPV commercialization efforts should target the experienced, impatient user who highly values design and functionality. (C) 2016 Elsevier B.V. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000383304100015 | Publication Date | 2016-06-27 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0927-0248 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.784 | Times cited | 2 | Open Access | |
Notes | ; Sebastien Lizin thanks the Research Foundation Flanders (FWO) for funding his postdoctoral mandate with Grant number 12G5415N, without which it would have been impossible to revise this work. ; | Approved ![]() |
Most recent IF: 4.784 | ||
Call Number | UA @ admin @ c:irua:137107 | Serial | 6207 | ||
Permanent link to this record |