| |
Records |
Links |
|
Author |
Kovalevsky, A.; Buysse, C.; Snijkers, F.; Buekenhoudt, A.; Luyten, J.; Kretzschmar, J.; Lenaerts, S. |
|
| |
Title |
Oxygen exchange-limited transport and surface activation of Ba0.5Sr0.5Co0.8Fe0.2O3-\delta capillary membranes |
Type |
A1 Journal article |
| |
Year |
2011 |
Publication |
Journal of membrane science |
Abbreviated Journal |
J Membrane Sci |
|
| |
Volume |
368 |
Issue |
1/2 |
Pages |
223-232 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
Analysis of oxygen permeation fluxes through Ba0.5Sr0.5Co0.8Fe0.2O3−δ (BSCF) capillary membranes, fabricated via a phase-inversion spinning technique using polysulfone as binder, showed a significant limiting role of the surface-oxygen exchange kinetics. Within the studied temperature and oxygen partial pressure ranges, the activation of core and shell sides of the BSCF capillary with praseodymium oxide (PrOx) resulted in an increase in permeation rate of about 300%. At 11231223 K the activated BSCF membranes demonstrate almost 3-times lower activation energies for the overall oxygen transport (not, vert, similar35 kJ/mol) than the non-activated capillaries, indicating that the mechanism of oxygen transport through the activated capillaries becomes significantly controlled by bulk diffusion limitations, allowing further improvement of the overall performance by decreasing the wall thickness. XRD, EDS and EPMA studies revealed the formation of (Pr,Ba,Sr)(Co,Fe)O3−δ perovskite-type oxides on the surface of the PrOx-modified membranes, which may be responsible for the drastic increase in oxygen exchange rate. At T > 1123 K both non-activated and activated Ba0.5Sr0.5Co0.8Fe0.2O3−δ membranes demonstrate stable performance with time, while at 1073 K only a small initial decrease in permeation was observed. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000286701800027 |
Publication Date |
2010-11-21 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0376-7388 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
6.035 |
Times cited |
21 |
Open Access |
|
|
| |
Notes |
; This work was supported by the German Helmholtz Alliance Project “MEM-BRAIN”, aiming at the development of gas separation membranes for zero-emission fossil fuel power plants. Experimental assistance of B. Molenberghs, W. Doyen, H. Chen, R. Kemps, M. Mertens, I. Thijs, and W. Bouwen (VITO) is gratefully acknowledged. ; |
Approved |
Most recent IF: 6.035; 2011 IF: 3.850 |
|
| |
Call Number |
UA @ admin @ c:irua:88072 |
Serial  |
5975 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Sóti, V.; Lenaerts, S.; Cornet, I. |
|
| |
Title |
Of enzyme use in cost-effective high solid simultaneous saccharification and fermentation processes |
Type |
A1 Journal article |
| |
Year |
2018 |
Publication |
Journal of biotechnology |
Abbreviated Journal |
J Biotechnol |
|
| |
Volume |
270 |
Issue |
270 |
Pages |
70-76 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL); Biochemical Wastewater Valorization & Engineering (BioWaVE) |
|
| |
Abstract |
Enzyme cost is considered to be one of the most significant factors defining the final product price in lignocellulose hydrolysis and fermentation. Enzyme immobilization and recycling can be a tool to decrease costs. However, high solid loading is a key factor towards high product titers, and recovery of immobilized enzymes from this thick liquid is often overlooked. This paper aims to evaluate the economic feasibility of immobilized enzymes in simultaneous saccharification and fermentation (SSF) of lignocellulose biomass in general, as well as the recuperation of magnetic immobilized enzymes (m-CLEAs) during high solid loading in simultaneous saccharification, detoxification and fermentation processes (SSDF) of lignocellulose biomass. Enzyme prices were obtained from general cost estimations by Klein-Marcuschamer et al. [Klein-Marcuschamer et al. (2012) Biotechnol. Bioeng. 109, 10831087]. During enzyme cost analysis, the influence of inoculum recirculation as well as a shortened fermentation time was explored. Both resulted in 15% decrease of final enzyme product price. Enzyme recuperation was investigated experimentally and 99.5 m/m% of m-CLEAs was recovered from liquid medium in one step, while 88 m/m% could still be recycled from a thick liquid with high solid concentrations (SSF fermentation broth). A mathematical model was constructed to calculate the cost of immobilized and free enzyme utilization and showed that, with current process efficiencies and commercial enzyme prices, the cost reduction obtained by enzyme immobilization can reach around 60% compared to free enzyme utilization, while lower enzyme prices will result in a lower percentage of immobilization related savings, but overall enzyme costs will decrease significantly. These results are applied in a case study, estimating the viability of shifting from sugar to lignocellulose substrate for a 100 t lactic acid fermentation batch. It was concluded that it will only be economically feasible if the enzymes are produced at the most optimistic variable cost and either the activity of the immobilized catalyst or the recovery efficiency is further increased. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000427556400009 |
Publication Date |
2018-02-08 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0168-1656 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
2.599 |
Times cited |
6 |
Open Access |
|
|
| |
Notes |
; This research is financed by the University of Antwerp [project number 15 FA100 002]. ; |
Approved |
Most recent IF: 2.599 |
|
| |
Call Number |
UA @ admin @ c:irua:149006 |
Serial |
5974 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Jammaer, J.; Aprile, C.; Verbruggen, S.W.; Lenaerts, S.; Pescarmona, P.P.; Martens, J.A. |
|
| |
Title |
A non-aqueous synthesis of TiO2SiO2 composites in supercritical CO2 for the photodegradation of pollutants |
Type |
A1 Journal article |
| |
Year |
2011 |
Publication |
Chemsuschem |
Abbreviated Journal |
Chemsuschem |
|
| |
Volume |
4 |
Issue |
10 |
Pages |
1457-1463 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
Titania/silica composites with different Ti/Si ratios are synthesized via a nonconventional synthesis route. The synthesis involves non-aqueous reaction of metal alkoxides and formic acid at 75 °C in supercritical carbon dioxide. The as-prepared composite materials contain nanometer-sized anatase crystallites and amorphous silica. Large specific surface areas are obtained. The composites are evaluated in the photocatalytic degradation of phenol in aqueous medium, and in the elimination of acetaldehyde from air. The highest photocatalytic activity in both processes is achieved with a composite containing 40 wt % TiO2. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000296497400010 |
Publication Date |
2011-05-20 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1864-5631 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
7.226 |
Times cited |
15 |
Open Access |
|
|
| |
Notes |
; The authors acknowledge sponsorship from CECAT and Methusalem (long-term financing of the Flemish government). We thank Dr. E. Gobechiya for assistance with XRD measurements and A. Lemaire for assistance with mercury porosimetry measurements. ; |
Approved |
Most recent IF: 7.226; 2011 IF: 6.827 |
|
| |
Call Number |
UA @ admin @ c:irua:93363 |
Serial |
5973 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Sóti, V.; Jacquet, N.; Apers, S.; Richel, A.; Lenaerts, S.; Cornet, I. |
|
| |
Title |
Monitoring the laccase reaction of vanillin and poplar hydrolysate |
Type |
A1 Journal article |
| |
Year |
2016 |
Publication |
Journal of chemical technology and biotechnology |
Abbreviated Journal |
J Chem Technol Biot |
|
| |
Volume |
91 |
Issue |
6 |
Pages |
1914-1922 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL); Biochemical Wastewater Valorization & Engineering (BioWaVE) |
|
| |
Abstract |
BACKGROUND Laccase is an intensively researched enzyme for industrial use. Except for decolorisation measurements, HPLC analysis is the conventional method for monitoring the phenolic removal during laccase enzyme reaction. This paper reports an investigation of the continuous UV absorbance follow-up of the laccase reaction with steam pretreated poplar hydrolysate. RESULTS Vanillin was used as a model substrate and lignocellulose xylose rich fraction (XRF) as a biologically complex substrate for laccase detoxification. The reaction was followed by HPLC-UV as well as by UV spectrometric measurements. Results suggest that the reaction can be successfully monitored by measuring the change of UV absorbance at 280 nm, without previous compound separation. In case of XRF experiments the spectrophotometric follow-up is especially useful, as HPLC analysis takes a long time and provides less information than in case of single substrates. The method seems to be suitable for optimization and process control. CONCLUSION The obtained results can help to construct a fast, easy and straightforward monitoring system for laccase-phenolic substrate reactions. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000375768300040 |
Publication Date |
2015-07-29 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0268-2575; 1097-4660 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
3.135 |
Times cited |
3 |
Open Access |
|
|
| |
Notes |
; This research is financed by the University of Antwerp (project number 15 FA100 002). ; |
Approved |
Most recent IF: 3.135 |
|
| |
Call Number |
UA @ admin @ c:irua:127694 |
Serial |
5972 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Buysse, C.; Michielsen, B.; Middelkoop, V.; Snijkers, F.; Buekenhondt, A.; Kretzschmar, J.; Lenaerts, S. |
|
| |
Title |
Modeling of the performance of BSCF capillary membranes in four-end and three-end integration mode |
Type |
A1 Journal article |
| |
Year |
2013 |
Publication |
Ceramics international |
Abbreviated Journal |
Ceram Int |
|
| |
Volume |
39 |
Issue |
4 |
Pages |
4113-4123 |
|
| |
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
Owing to their high surface-to-volume ratio, there has been an increasing research interest in mixed ionic electronic conducting (MIEC) capillary membranes for large-scale high temperature oxygen separation applications. They offer an energy-efficient solution for high temperature combustion processes in oxy-fuel and pre-combustion CO2 capture technologies used in fossil fuel power plants. In order to assess the effectiveness of these membranes in power plant applications, the impact of the geometry of Ba0.5Sr0.5Co0.8Fe0.2O3-delta (BSCF) capillaries on their performance in the three-end and four-end integration modes has been investigated and thoroughly discussed. The model's parameters were derived from four-end mode lab-scale experiments using gas-tight, macrovoid free and sulfur-free BSCF capillary membranes that were prepared by a phase-inversion spinning technique. The results of this modeling study revealed that in the four-end mode higher average oxygen fluxes and smaller total membrane areas can be obtained than in the three-end mode. This is due to the higher pO(2) gradient across the membrane wall. (C) 2012 Elsevier Ltd and Techna Group S.r.l. All rights reserved. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000318129100084 |
Publication Date |
2012-11-09 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0272-8842 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
2.986 |
Times cited |
4 |
Open Access |
|
|
| |
Notes |
; The authors wish to thank all the VITO staff involved in the project for their continued support, and in particular B. Molenberghs, W. Doyen, H. Beckers and S. Mullens. C. Buysse would like to acknowledge funding from VITO and the University of Antwerp for a Ph.D. studentship. This work has been performed in the framework of the German Helmholtz Alliance Project “MEM-BRAIN”, aiming at the development of gas separation membranes for zero-emission fossil fuel power plants. ; |
Approved |
Most recent IF: 2.986; 2013 IF: 2.086 |
|
| |
Call Number |
UA @ admin @ c:irua:109020 |
Serial |
5971 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Meire, M.; Verbruggen, S.W.; Lenaerts, S.; Lommens, P.; Van Der Voort, P.; Van Driessche, I. |
|
| |
Title |
Microwave-assisted synthesis of mesoporous titania with increased crystallinity, specific surface area, and photocatalytic activity |
Type |
A1 Journal article |
| |
Year |
2016 |
Publication |
Journal of materials science |
Abbreviated Journal |
J Mater Sci |
|
| |
Volume |
51 |
Issue |
21 |
Pages |
9822-9829 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
Mesoporous titanium dioxide is a material finding its use in a wide range of applications. For many of these, it is important to achieve a high degree of crystallinity in the material. It is generally accepted that the use of the soft templating approach to synthesize mesoporous titania, results in a compromise between crystallinity and specific surface area due to thermal instability of the used templates. In this paper, we explore how the use of microwave irradiation can influence the crystallinity, specific surface area, and the electronic properties of mesoporous titania. Therefore, we combined microwave radiation with an evaporation-induced self-assembly (EISA) synthesis. We show that additional microwave treatment at carefully chosen synthesis steps can enhance the crystallinity with 20 % without causing significant loss of surface area (>360 m2/g). Surface photovoltage measurements were used to investigate the electronic properties. The photocatalytic activity of the samples was evaluated in aqueous media by following the degradation of an industrial dye, methylene blue, and the herbicide isoproturon under UV irradiation and in gaseous media looking at the degradation of acetaldehyde, a common indoor pollutant under UVA irradiation. In all cases, the microwave treatment results in more active materials. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000381182200023 |
Publication Date |
2016-07-18 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0022-2461 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
2.599 |
Times cited |
8 |
Open Access |
|
|
| |
Notes |
; M. Meire and S. W. Verbruggen acknowledge the FWO-Flanders (Fund for Scientific Research-Flanders) for financial support. We want to thank T. Planckaert for the N<INF>2</INF> sorption measurements, J. Watte for the XRD measurements, and professor K. De Buysser for the quantitative Rietveld refinements. ; |
Approved |
Most recent IF: 2.599 |
|
| |
Call Number |
UA @ admin @ c:irua:140098 |
Serial |
5970 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Billet, J.; Vandewalle, S.; Meire, M.; Blommaerts, N.; Lommens, P.; Verbruggen, S.W.; De Buysser, K.; Du Prez, F.; Van Driesche, I. |
|
| |
Title |
Mesoporous TiO2 from poly(N,N-dimethylacrylamide)-b-polystyrene block copolymers for long-term acetaldehyde photodegradation |
Type |
A1 Journal article |
| |
Year |
2019 |
Publication |
Journal of materials science |
Abbreviated Journal |
J Mater Sci |
|
| |
Volume |
55 |
Issue |
55 |
Pages |
1933-1945 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
Although already some mesoporous (2–50 nm) sol–gel TiO2 synthesis strategies exist, no pore size control beyond the 12 nm range is possible without using specialized organic structure-directing agents synthetized via controlled anionic/radical polymerizations. Here, we present the use of reversible addition–fragmentation chain transfer (RAFT) polymerization as a straightforward and industrial applicable alternative to the existing controlled polymerization methods for structure-directing agent synthesis. Poly(N,N-dimethylacrylamide)-block-polystyrene (PDMA-b-PS) block copolymer, synthesized via RAFT, was chosen as structure-directing agent for the formation of the mesoporous TiO2. Crack-free thin layers TiO2 with tunable pores from 8 to 45 nm could be acquired. For the first time, in a detailed and systematic approach, the influence of the block size and dispersity of the block copolymer is experimentally screened for their influence on the final meso-TiO2 layers. As expected, the mesoporous TiO2 pore sizes showed a clear correlation to the polystyrene block size and the dispersity of the PDMA-b-PS block copolymer. Surprisingly, the dispersity of the polymer was shown not to be affecting the standard deviation of the pores. As a consequence, RAFT could be seen as a viable alternative to the aforementioned controlled polymerization reactions for the synthesis of structure-directing agents enabling the formation of mesoporous pore size-controlled TiO2. To examine the photocatalytic activity of the mesoporous TiO2 thin layers, the degradation of acetaldehyde, a known indoor pollutant, was studied. Even after 3 years of aging, the TiO2 thin layer retained most of its activity. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000494929300001 |
Publication Date |
2019-11-05 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0022-2461 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
2.599 |
Times cited |
2 |
Open Access |
|
|
| |
Notes |
; Ghent University is acknowledged for funding the research presented in this paper. M. Meire and S. W. Verbruggen acknowledge the FWO-Flanders (Fund for Scientific Research-Flanders) for financial support. The authors thank Bernhard De Meyer for the SEC analysis, Hannes Rijckaert for the cross-sectional analysis, Tom Planckaert for BET analysis of the meso-TiO<INF>2</INF> powders, Jeroen Kint for the porosiellipsometry tests and Frank Driessen for the MALDI-TOF analysis. ; |
Approved |
Most recent IF: 2.599 |
|
| |
Call Number |
UA @ admin @ c:irua:163842 |
Serial |
5969 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Caretti, I.; Keulemans, M.; Verbruggen, S.W.; Lenaerts, S.; Van Doorslaer, S. |
|
| |
Title |
Light-induced processes in plasmonic Gold/TiO2 photocatalysts studied by electron paramagnetic resonance |
Type |
A1 Journal article |
| |
Year |
2015 |
Publication |
Topics in catalysis |
Abbreviated Journal |
Top Catal |
|
| |
Volume |
58 |
Issue |
12 |
Pages |
776-782 |
|
| |
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
X-band and W-band continuous-wave (CW) electron paramagnetic resonance (EPR) was used to study in situ light-induced (LI) mechanisms in commercial P90 titania (90 % anatase/10 % rutile) compared to plasmon-enhanced Au-P90 photocatalyst. These materials were excited using UV and 532 nm visible light to generate different excitation states and distinguish pure charge separation from plasmon-assisted resonance processes. Up to nine different photoinduced species of trapped electrons and holes were identified. LI CW EPR of P90 is presented for the first time, showing a UV excitation response similar to the well-known mixed-phase P25 titania. It is shown that incorporation of Au nanoparticles in Au-P90 and formation of a Schottky junction affects the charge separation state of the catalyst under UV light. Moreover, Au impregnation activated P90 through plasmon hot electron injection under visible light excitation (plasmonic sensitization effect). In general, EPR proved to be crucial to determine the different photoexciation paths and reactions that regulate plasmonic photocatalysis. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000360011200008 |
Publication Date |
2015-08-03 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1022-5528 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
2.486 |
Times cited |
22 |
Open Access |
|
|
| |
Notes |
; IC and SVD acknowledge the Research Foundation-Flanders (FWO) for financial support (Grant G.0687.13). SV thanks FWO for financial support through a postdoctoral fellowship and MK acknowledges the agency for Innovation by Science and Technology in Flanders (IWT) for financial support (Ph.D. Grant). ; |
Approved |
Most recent IF: 2.486; 2015 IF: 2.365 |
|
| |
Call Number |
UA @ admin @ c:irua:127413 |
Serial |
5968 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
van Walsem, J.; Roegiers, J.; Modde, B.; Lenaerts, S.; Denys, S. |
|
| |
Title |
Integration of a photocatalytic multi-tube reactor for indoor air purification in HVAC systems : a feasibility study |
Type |
A1 Journal article |
| |
Year |
2018 |
Publication |
Environmental Science and Pollution Research |
Abbreviated Journal |
Environ Sci Pollut R |
|
| |
Volume |
25 |
Issue |
18 |
Pages |
18015-18026 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
This work is focused on an in-depth experimental characterization of multi-tube reactors for indoor air purification integrated in ventilation systems. Glass tubes were selected as an excellent photocatalyst substrate to meet the challenging requirements of the operating conditions in a ventilation system in which high flow rates are typical. Glass tubes show a low-pressure drop which reduces the energy demand of the ventilator, and additionally, they provide a large exposed surface area to allow interaction between indoor air contaminants and the photocatalyst. Furthermore, the performance of a range of P25-loaded sol-gel coatings was investigated, based on their adhesion properties and photocatalytic activities. Moreover, the UV light transmission and photocatalytic reactor performance under various operating conditions were studied. These results provide vital insights for the further development and scaling up of multi-tube reactors in ventilation systems which can provide a better comfort, improved air quality in indoor environments, and reduced human exposure to harmful pollutants. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000436879200071 |
Publication Date |
2018-04-24 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0944-1344; 1614-7499 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
2.741 |
Times cited |
3 |
Open Access |
|
|
| |
Notes |
; J.V.W. acknowledges the Agentschap Innoveren and Ondernemen for a PhD fellowship. ; |
Approved |
Most recent IF: 2.741 |
|
| |
Call Number |
UA @ admin @ c:irua:150946 |
Serial |
5967 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Van Wesenbeeck, K.; Hauchecorne, B.; Lenaerts, S. |
|
| |
Title |
Integration of a photocatalytic coating in a corona discharge unit for plasma assisted catalysis |
Type |
A1 Journal article |
| |
Year |
2013 |
Publication |
Journal of environmental solutions |
Abbreviated Journal |
|
|
| |
Volume |
2 |
Issue |
1 |
Pages |
16-24 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
The combination of a non-thermal plasma with catalysis is considered as a sustainable indoor air purification technology to achieve complete oxidation at reduced energy cost with a longer electrode lifetime. An optimal window of operation for plasma assisted catalysis is found by varying the polarity, the applied voltage, the relative humidity of the gas phase and the configuration of the plasma reactor. The results show that, in general, negative corona discharge can obtain higher nitric oxide (NO) conversion efficiencies compared to positive corona. It is also clear that at higher applied voltages, higher conversion efficiency can be reached. The effect of relative humidity, however, is not found to be significant in the range (0 20.3 %) tested in this work. Additionally, the configuration of the plasma reactor is changed by varying the amount of pins that are attached at the collector electrode. The results show that there is an optimum at 10 pairs of pins to obtain a high conversion efficiency of NO. By applying a coating on the collector electrode of the plasma reactor, it is possible to see the influence of the coating on the performance of the plasma system, which was operating in the previously found optimal window. It stands clear that the use of a plasma assisted catalysis system has high potential as an integrated and sustainable indoor air purification technology. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
|
Publication Date |
|
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
|
ISBN |
|
Additional Links |
UA library record |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ admin @ c:irua:108646 |
Serial |
5966 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
de Baere, K.; Verstraelen, H.; Lemmens, L.; Lenaerts, S.; Potters, G. |
|
| |
Title |
In situ study of the parameters quantifying the corrosion in ballast tanks and an evaluation of improving alternative |
Type |
P3 Proceeding |
| |
Year |
2011 |
Publication |
|
Abbreviated Journal |
|
|
| |
Volume |
|
Issue |
|
Pages |
|
|
| |
Keywords |
P3 Proceeding; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
An in situ study of more than 100 ballast tanks of merchant marine vessels looks to the corrosion process in these tanks from another perspective. The developed corrosion model shows major similarities with earlier studies based on laboratory experiments. The field work exposes the influence of ship construction parameters such as land of construction, coating type and the presence of sacrificial anodes on the corrosion process in the ballast tanks. Possible alternatives for vessels constructed with ordinary grade A steel and coated according to IMO PSPC standards are presented, even though further research is required to come to final conclusions. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
|
Publication Date |
|
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
|
ISBN |
|
Additional Links |
UA library record |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ admin @ c:irua:88937 |
Serial |
5965 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Verstraelen, H.; de Baere, K.; Schillemans, W.; Lemmens, L.; Dewil, R.; Lenaerts, S.; Potters, G. |
|
| |
Title |
In situ study of ballast tank corrosion on ships: part 2 |
Type |
A1 Journal article |
| |
Year |
2009 |
Publication |
Materials performance |
Abbreviated Journal |
Mater Performance |
|
| |
Volume |
48 |
Issue |
11 |
Pages |
54-57 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Theory of quantum systems and complex systems; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
A study was undertaken to determine causes and effects of corrosion processes in ballast tanks. Part 1 of this article (October 2009 MP) described the data collection. Part 2 describes the development of a corrosion index (CI) derived from the general International Association of Classification Societies corrosion assessment methods. The CI can be used in situ to assess ballast tank corrosion. An average timeline for-corrosion of tanks is presented. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
|
Publication Date |
|
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0094-1492 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
0.149 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 0.149; 2009 IF: 0.124 |
|
| |
Call Number |
UA @ admin @ c:irua:79761 |
Serial |
5964 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Verstraelen, H.; de Baere, K.; Schillemans, W.; Lemmens, L.; Dewil, R.; Lenaerts, S.; Potters, G. |
|
| |
Title |
In situ study of ballast tank corrosion on ships: part 1 |
Type |
A1 Journal article |
| |
Year |
2009 |
Publication |
Materials performance |
Abbreviated Journal |
Mater Performance |
|
| |
Volume |
48 |
Issue |
10 |
Pages |
48-51 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Theory of quantum systems and complex systems; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
|
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
|
Publication Date |
|
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0094-1492 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles; WoS full record; WoS citing articles |
|
| |
Impact Factor |
0.149 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 0.149; 2009 IF: 0.124 |
|
| |
Call Number |
UA @ admin @ c:irua:78547 |
Serial |
5963 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Lenaerts, S.; Honoré, M.; Huyberechts, G.; Roggen, J.; Maes, G. |
|
| |
Title |
In situ infrared and electrical characterization of tin dioxide gas sensors in nitrogen/oxygen mixtures at temperatures up to 720 K |
Type |
A1 Journal article |
| |
Year |
1994 |
Publication |
Sensors and actuators : B : chemical |
Abbreviated Journal |
|
|
| |
Volume |
19 |
Issue |
|
Pages |
478-482 |
|
| |
Keywords |
A1 Journal article |
|
| |
Abstract |
FT-IR spectroscopy and impedance measurements of tin dioxide sensor materials at working temperatures up to 450 °C in atmospheres with varying O2/N2 ratio are used as an in situ probe to study the interactions at the surface of the semiconducting oxide. Every diminution in the oxygen content above the sample induces a broad IR absorption band (X-band) between 2300700 cm−1 with a few small peaks in the 1400850 cm−1 region of the spectrum superimposed on it. The X-band results from the enchanced electron concentration in the bulk of the tin dioxide domain. The fine structure is due to the absorption of several kinds of surface oxygen species associated vibration modes. The porous tin dioxide consists of domains were the outward shell is depleted of electrons by the formation of adsorbed O− species on oxygen surface sites, SO(O− species. In our proposed model for the impedance data this gives rise to a parallel RpCp circuit for the domain boundary characteristics and to an Rs parameter for the intradomain resistance. The evolution of these IR and impedance spectroscopic effects with temperature and oxygen content is used to set up, to confirm and refine a physicochemical operation model of tin dioxide gas sensor. This model consists of a sensitizing reaction sequence in the presence of oxygen and a gas-detection reaction sequence when a reducing gas is present. Based on this model, the principal disadvantages of this type of gas sensor become clear. Every factor that influences the concentration of SO(O−) species, causes a conductance modification. If we can control and direct the nature, the number and the arrangement of the tin dioxide domains, a directed development and improvement of the sensor characteristics is possible. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
A1994NN90000040 |
Publication Date |
2002-07-25 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0925-4005 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
no |
|
| |
Call Number |
UA @ admin @ c:irua:82014 |
Serial |
5962 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
de Baere, K.; Verstraelen, H.; Dewil, R.; Lemmens, L.; Lenaerts, S.; Nkunzimana, T.; Potters, G. |
|
| |
Title |
Impact of tank construction on corrosion of ship ballast tanks |
Type |
A1 Journal article |
| |
Year |
2010 |
Publication |
Materials performance |
Abbreviated Journal |
Mater Performance |
|
| |
Volume |
49 |
Issue |
5 |
Pages |
48-54 |
|
| |
Keywords |
A1 Journal article; Theory of quantum systems and complex systems; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
|
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
|
Publication Date |
|
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0094-1492 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
0.149 |
Times cited |
|
Open Access |
|
|
| |
Notes |
; ; |
Approved |
Most recent IF: 0.149; 2010 IF: 0.055 |
|
| |
Call Number |
UA @ admin @ c:irua:82385 |
Serial |
5961 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Tytgat, T.; Smits, M.; Lenaerts, S.; Verbruggen, S.W. |
|
| |
Title |
Immobilization of TiO2 into self-supporting photocatalytic foam : influence of calcination temperature |
Type |
A1 Journal article |
| |
Year |
2014 |
Publication |
International journal of applied ceramic technology |
Abbreviated Journal |
Int J Appl Ceram Tec |
|
| |
Volume |
11 |
Issue |
4 |
Pages |
714-722 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
Immobilization of photocatalytic powder is crucial to obtain industrially relevant purification processes. To achieve this goal, self-supporting TiO2 foams were manufactured by a polyacrylamide gel process. These gels were calcined at different temperatures to study the effect of the calcination temperature on foam characteristics (rigidity, crystallinity, and porosity) and its influence on photocatalytic activity. The results show that an optimal degradation is achieved for those foams calcined between 700 and 800°C. Calcination at higher temperatures results in a steep decrease in activity, explained by stability issues of the material due to formation of Na2SO4 phases and a larger rutile fraction. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000339051500012 |
Publication Date |
2013-04-24 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1546-542x |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
1.048 |
Times cited |
2 |
Open Access |
|
|
| |
Notes |
; This work was supported by a PhD grant from the Institute of Innovation by Science and Technology in Flanders (IWT). ; |
Approved |
Most recent IF: 1.048; 2014 IF: 1.320 |
|
| |
Call Number |
UA @ admin @ c:irua:117295 |
Serial |
5960 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Tytgat, T.; Lenaerts, S. |
|
| |
Title |
Immobilisation of TiO2 into self-supporting photocatalytic foam : influence of acidity on porosity and light penetration |
Type |
P3 Proceeding |
| |
Year |
2012 |
Publication |
|
Abbreviated Journal |
|
|
| |
Volume |
|
Issue |
|
Pages |
|
|
| |
Keywords |
P3 Proceeding; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
|
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
|
Publication Date |
|
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
|
ISBN |
978-989-97667-4-7 |
Additional Links |
UA library record |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ admin @ c:irua:99066 |
Serial |
5959 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Van Hal, M.; Verbruggen, S.W.; Yang, X.-Y.; Lenaerts, S.; Tytgat, T. |
|
| |
Title |
Image analysis and in situ FTIR as complementary detection tools for photocatalytic soot oxidation |
Type |
A1 Journal article |
| |
Year |
2019 |
Publication |
Chemical engineering journal |
Abbreviated Journal |
Chem Eng J |
|
| |
Volume |
367 |
Issue |
367 |
Pages |
269-277 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
Air pollution, especially particulate matter (PM), is an increasingly urgent problem in urban environments, causing both short and long-term health problems, climate interference and aesthetical problems due to building fouling. Photocatalysis has been shown to be a possible solution to that end. In this work two complementary detection methods for photocatalytic soot oxidation are studied and their advantages and disadvantages are discussed. First, a colour-based digital image analysis method is drastically improved towards an accurate, detailed and straightforward detection tool, that enables simultaneous measurement of the degradation of different grades of soot fouling (for instance a shallow soot haze versus condensed soot deposits). In the next part, a second soot oxidation detection method is presented based on in situ FTIR spectroscopy. This method has the additional advantage of providing more insight into the photocatalytic soot degradation process by monitoring both gaseous and adsorbed intermediates as well as reaction products while the reactions are ongoing. As an illustration, the proposed detection strategies were applied on four different commercially available and synthesized photocatalytic materials. The digital image analysis showed that P25 (Evonik) is the fastest photocatalytic soot degrader of all studied materials for both a uniform soot haze as well as concentrated soot spots. Application of the in situ method showed that for all studied materials adsorbed formate-related surface species were formed and that commercially available ZnO nanopowder has the highest specificity towards complete mineralization into CO2. With this we aim to provide a set of complementary experimental tools for the convenient, reliable, realistic and standardised detection of photocatalytic soot degradation. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000461380400028 |
Publication Date |
2019-02-23 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1385-8947; 1873-3212 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
6.216 |
Times cited |
1 |
Open Access |
|
|
| |
Notes |
; M.V.H. acknowledges the Research Foundation-Flanders (FWO) for a doctoral fellowship. M.V.H., S.W.V., S.L. and X-Y.Y. thank the FWO and the National Natural Science Foundation of China (NSFC) for funding an international collaboration project. Mr. M. Minjauw is greatly thanked for his help in the AFM measurements. ; |
Approved |
Most recent IF: 6.216 |
|
| |
Call Number |
UA @ admin @ c:irua:157789 |
Serial |
5958 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Xiao, S.; Lu, Y.; Xiao, B.-Y.; Wu, L.; Song, J.-P.; Xiao, Y.-X.; Wu, S.-M.; Hu, J.; Wang, Y.; Chang, G.-G.; Tian, G.; Lenaerts, S.; Janiak, C.; Yang, X.-Y.; Su, B.-L. |
|
| |
Title |
Hierarchically dual-mesoporous TiO2 microspheres for enhanced photocatalytic properties and lithium storage |
Type |
A1 Journal article |
| |
Year |
2018 |
Publication |
Chemistry: a European journal |
Abbreviated Journal |
Chem-Eur J |
|
| |
Volume |
24 |
Issue |
50 |
Pages |
13246-13252 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
Hierarchically dual‐mesoporous TiO2 microspheres have been synthesized via a solvothermal process in the presence of 1‐butyl‐3‐methylmidazolium tetrafluoroborate ([BMIm][BF4]) and diethylenetriamine (DETA) as co‐templates. Secondary mesostructured defects in the hierarchical TiO2 microspheres produce the oxygen vacancies, which not only significantly enhance the photocatalytic activity on degrading methyl blue (over 1.7 times to P25) and acetone (over 2.9 times of P25), but which also are beneficial for lithium storage. Moreover, we propose a mechanism to obtain a better understanding of the role of dual mesoporosity of TiO2 microspheres for enhancing the molecular diffusion, ion transportation and electron transformation. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000443804100025 |
Publication Date |
2018-06-21 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0947-6539 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
5.317 |
Times cited |
6 |
Open Access |
|
|
| |
Notes |
; This work is supported by the National Key R&D Program of China (2017YFC1103800), the Program for Changjiang Scholars and Innovative Research Team in University (IRT 15R52), the National Natural Science Foundation of China (U1662134, U1663225, 51472190, 51611530672, 51503166, 21706199, 21711530705), the International Science & Technology Cooperation Program of China (2015DFE52870), the Natural Science Foundation of Hubei Province (2016CFA033, 2017CFB487), the Open Project Program of State Key Laboratory of Petroleum Pollution Control (PPC2016007), and the CNPC Research Institute of Safety and Environmental Technology. ; |
Approved |
Most recent IF: 5.317 |
|
| |
Call Number |
UA @ admin @ c:irua:151812 |
Serial |
5957 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Dong, Y.; Chen, S.-Y.; Lu, Y.; Xiao, Y.-X.; Hu, J.; Wu, S.-M.; Deng, Z.; Tian, G.; Chang, G.-G.; Li, J.; Lenaerts, S.; Janiak, C.; Yang, X.-Y.; Su, B.-L. |
|
| |
Title |
Hierarchical MoS2@TiO2 heterojunctions for enhanced photocatalytic performance and electrocatalytic hydrogen evolution |
Type |
A1 Journal article |
| |
Year |
2018 |
Publication |
Chemistry: an Asian journal |
Abbreviated Journal |
Chem-Asian J |
|
| |
Volume |
13 |
Issue |
12 |
Pages |
1609-1615 |
|
| |
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
Hierarchical MoS2@TiO2 heterojunctions were synthesized through a one-step hydrothermal method by using protonic titanate nanosheets as the precursor. The TiO2 nanosheets prevent the aggregation of MoS2 and promote the carrier transfer efficiency, and thus enhance the photocatalytic and electrocatalytic activity of the nanostructured MoS2. The obtained MoS2@TiO2 has significantly enhanced photocatalytic activity in the degradation of rhodamineB (over 5.2times compared with pure MoS2) and acetone (over 2.8times compared with pure MoS2). MoS2@TiO2 is also beneficial for electrocatalytic hydrogen evolution (26times compared with pure MoS2, based on the cathodic current density). This work offers a promising way to prevent the self-aggregation of MoS2 and provides a new insight for the design of heterojunctions for materials with lattice mismatches. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000435773300011 |
Publication Date |
2018-04-10 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1861-4728; 1861-471x |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
4.083 |
Times cited |
22 |
Open Access |
|
|
| |
Notes |
; This work was supported by the National Key R&D Program of China (2017YFC1103800), PCSIRT (IRT15R52), NSFC (U1662134, U1663225, 51472190, 51611530672, 51503166, 21706199, 21711530705), ISTCP (2015DFE52870), HPNSF (2016CFA033, 2017CFB487), and SKLPPC (PPC2016007). ; |
Approved |
Most recent IF: 4.083 |
|
| |
Call Number |
UA @ admin @ c:irua:151971 |
Serial |
5956 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Verbruggen, S.W.; Van Hal, M.; Bosserez, T.; Rongé, J.; Hauchecorne, B.; Martens, J.A.; Lenaerts, S. |
|
| |
Title |
Harvesting hydrogen gas from air pollutants with an un-biased gas phase photo-electrochemical cell |
Type |
A1 Journal article |
| |
Year |
2017 |
Publication |
Chemsuschem |
Abbreviated Journal |
Chemsuschem |
|
| |
Volume |
10 |
Issue |
7 |
Pages |
1413-1418 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
The concept of an all-gas-phase photo-electrochemical cell (PEC) producing hydrogen gas from volatile organic contaminated gas and light is presented. Without applying any external bias, organic contaminants are degraded and hydrogen gas is produced in separate electrode compartments. The system works most efficiently with organic pollutants in inert carrier gas. In the presence of oxygen gas, the cell performs less efficiently but still significant photocurrents are generated, showing the cell can be run on organic contaminated air. The purpose of this study is to demonstrate new application opportunities of PEC technology and to encourage further advancement toward photo-electrochemical remediation of air pollution with the attractive feature of simultaneous energy recovery and pollution abatement. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000398838600017 |
Publication Date |
2017-02-08 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1864-5631 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
7.226 |
Times cited |
6 |
Open Access |
|
|
| |
Notes |
; S.W.V. and J.R. acknowledge the Research Foundation-Flanders (FWO) for a postdoctoral fellowship. T.B. and J.A.M. acknowledge the Flemish government for long-term structural funding (Methusalem). Nicolaas Schewyck is greatly thanked for his experimental work during his master thesis. ; |
Approved |
Most recent IF: 7.226 |
|
| |
Call Number |
UA @ admin @ c:irua:140922 |
Serial |
5955 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Lenaerts, S.; Roggen, J.; Maes, G. |
|
| |
Title |
FT-IR characterization of tin dioxide gas sensor materials under working conditions |
Type |
A1 Journal article |
| |
Year |
1995 |
Publication |
Spectrochimica acta: part A: molecular and biomolecular spectroscopy |
Abbreviated Journal |
|
|
| |
Volume |
51 |
Issue |
5 |
Pages |
883-894 |
|
| |
Keywords |
A1 Journal article |
|
| |
Abstract |
In this work self-supporting tin dioxide disks are characterized using FT-IR spectroscopy in the presence of a reducing gas in air, and in different O2/N2 mixtures at temperatures varying from room temperature up to 450°C. Every factor inducing a change in the oxygen content of the gas atmosphere above the tin dioxide, as for instance a temperature change, a surface reaction or adsorption of another species, induces a broad, intense IR absorption band with discrete weak bands superimposed on it. This broad absorption is assigned to the electronic transition from a native donor level, the oxygen vacancy in the bulk of the domain, to the conduction band of the tin dioxide material. For the interpretation of the narrow, superimposed absorptions, two hypotheses remain. The results demonstrate that FT-IR spectroscopy is an extremely suitable technique for the characterization of semiconducting metal oxide sensors, since it allows to follow in situ the processes in the bulk, at the surface and in the surrounding gas atmosphere of the sensor material at working temperature as well as in the presence of reducing gases in air. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
A1995RJ99900014 |
Publication Date |
2003-04-05 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1386-1425 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles; WoS full record; WoS citing articles |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
no |
|
| |
Call Number |
UA @ admin @ c:irua:82015 |
Serial |
5954 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
De Baere, K.; Verstraelen, H.; Lemmens, L.; Lenaerts, S.; Dewil, R.; Van Ingelgem, Y.; Potters, G. |
|
| |
Title |
A field study of the effectiveness of sacrificial anodes in ballast tanks of merchant ships |
Type |
A1 Journal article |
| |
Year |
2014 |
Publication |
Journal of marine science and technology |
Abbreviated Journal |
J Mar Sci Tech-Japan |
|
| |
Volume |
19 |
Issue |
1 |
Pages |
116-123 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
Sacrificial anodes have become a standard practice for the protection of ballast tanks of merchant vessels against corrosive damage. A well protected tank should extend the life span of a ship and consequently enhances its economic value. An in situ survey comprising more than 100 merchant vessels provided the opportunity to measure the impact of these anodes on the life expectancy of these vessels. Contrary to the general belief of these anodes beneficial effect, no significant difference was found in our observations in terms of corrosion occurrence between ship populations with and without sacrificial anodes, across all ship ages. This may be explained by the highly variable conditions and the complex geometry in a ballast tank severely impede optimal and straightforward installation of these anodes in these tanks. Also, poorly placed anodes in it may harm the integrity of the coating of the tank. We therefore plead for uniform and clear rules on anode installation and inspection. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000332693300008 |
Publication Date |
2013-07-29 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0948-4280 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
0.838 |
Times cited |
3 |
Open Access |
|
|
| |
Notes |
; This work was financed by a BOF Academisation grant of the University of Antwerp and the Antwerp Maritime Academy. ; |
Approved |
Most recent IF: 0.838; 2014 IF: 0.805 |
|
| |
Call Number |
UA @ admin @ c:irua:109348 |
Serial |
5953 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Verbruggen, S.W.; Masschaele, K.; Moortgat, E.; Korany, T.E.; Hauchecorne, B.; Martens, J.A.; Lenaerts, S. |
|
| |
Title |
Factors driving the activity of commercial titanium dioxide powders towards gas phase photocatalytic oxidation of acetaldehyde |
Type |
A1 Journal article |
| |
Year |
2012 |
Publication |
Catalysis science & technology |
Abbreviated Journal |
Catal Sci Technol |
|
| |
Volume |
2 |
Issue |
11 |
Pages |
2311-2318 |
|
| |
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
The photocatalytic activity of two commercial titanium dioxide powders (Cristal Global, Millennium PC500 and Evonik, P25) is compared towards acetaldehyde degradation in the gas phase. In contrast to the extensive literature available, we found a higher activity for the PC500 than for the P25 coating. Here, we present a comprehensive characterization of the bulk and surface properties of both powders. Our comparison shows that the material properties that dominate the overall photocatalytic activity in gas phase differ from those required for the photodegradation of water-borne pollutants. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000310863900020 |
Publication Date |
2012-06-13 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
2044-4753; 2044-4761 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
5.773 |
Times cited |
33 |
Open Access |
|
|
| |
Notes |
; S.W.V. acknowledges the Research Foundation of Flanders (FWO) for the financial support. J.A.M acknowledges long term funding (Methusalem). ; |
Approved |
Most recent IF: 5.773; 2012 IF: 3.753 |
|
| |
Call Number |
UA @ admin @ c:irua:105162 |
Serial |
5952 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Van Noyen, J.; Middelkoop, V.; Buysse, C.; Kovalevsky, A.; Snijkers, F.; Buekenhoudt, A.; Mullens, S.; Luyten, J.; Kretzschmar, J.; Lenaerts, S. |
|
| |
Title |
Fabrication of perovskite capillary membranes for high temperature gas separation |
Type |
A1 Journal article |
| |
Year |
2012 |
Publication |
Catalysis today |
Abbreviated Journal |
Catal Today |
|
| |
Volume |
193 |
Issue |
1 |
Pages |
172-178 |
|
| |
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
Oxygen-permeable perovskites with mixed ionic-electronic conducting properties can play an important role in carbon capture and storage techniques. Their ability to separate oxygen from air is needed, more specifically, in oxy-fuel and pre-combustion technologies. In this work, the first detailed comparative analysis and new results are reported on four types of Ba0.5Sr0.5Co0.8Fe0.2O3-delta (BSCF) capillary membranes: non-coated sulphur-containing; catalyst-coated sulphur-containing; non-coated sulphur-free and catalyst-coated sulphur-free. The fabrication of BSCF capillaries by a spinning technique based on phase inversion is further discussed and their oxygen separation performances are interpreted. The comparison of the performance of these different generations of BSCF capillaries of similar dimensions demonstrates a significant impact of the sulphur contamination on both the oxygen flux through the membrane and the activation energy of the overall oxygen transport mechanism. Careful attention is paid to the effect of activation layers on both sulphur-free and sulphur-containing types of capillaries. Additional long-term testing of the sulphur-free BSCF capillaries is presented, where partial decomposition of the membrane surface was observed due to kinetic demixing. (c) 2012 Elsevier B.V. All rights reserved. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000308675900025 |
Publication Date |
2012-04-15 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0920-5861 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
4.636 |
Times cited |
9 |
Open Access |
|
|
| |
Notes |
; The authors want to express their thanks to the VITO personnel for their continuous support, especially B. Molenberghs, W. Doyen (Separation and Conversion Technology, VITO), R. Kemps, M. Mertens, I. Thijs, M. Schoeters, W. Bouwen and J. Cooymans (Materials Department, VITO). C. Buysse thankfully acknowledges a Ph.D. scholarship provided by VITO and the University of Antwerp. This work is performed in the framework of the German Helmholtz Alliance Project “MEM-BRAIN”, aiming at the development of gas separation membranes for zero-emission fossil fuel power plants. ; |
Approved |
Most recent IF: 4.636; 2012 IF: 2.980 |
|
| |
Call Number |
UA @ admin @ c:irua:101797 |
Serial |
5951 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Buysse, C.; Kovalevsky, A.; Snijkers, F.; Buekenhoudt, A.; Mullens, S.; Luyten, J.; Kretzschmar, J.; Lenaerts, S. |
|
| |
Title |
Fabrication and oxygen permeability of gastight, macrovoid-free Ba0.5Sr0.5Co0.8Fe0.2O3-\delta capillaries for high temperature gas separation |
Type |
A1 Journal article |
| |
Year |
2010 |
Publication |
Journal of membrane science |
Abbreviated Journal |
J Membrane Sci |
|
| |
Volume |
359 |
Issue |
1-2 |
Pages |
86-92 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
Oxygen-permeable perovskites with mixed ionic-electronic conducting properties can play an important role in the separation of oxygen from air which is needed in the oxy-fuel and pre-combustion technologies for the removal and capture of CO2. In this work, gastight, macrovoid-free Ba0.5Sr0.5Co0.8Fe0.2O3−δ (BSCF) capillaries were successfully shaped by a phase-inversion spinning technique, followed by calcination and sintering. It was found that both the rheology of the ceramic suspension and the composition of bore liquid and coagulation bath are key factors for making macrovoid-free green capillaries. Gastight BSCF capillaries were obtained by sintering for 5 h at 1100 °C. The sintered BSCF capillaries contained a significant amount of BaSO4 due to a reaction with the polysulfone binder during calcination. The oxygen permeation flux through the BSCF capillaries was measured and compared to literature data on BSCF disk and hollow fiber membranes measured in similar conditions. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000279953300010 |
Publication Date |
2009-10-30 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0376-7388 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
6.035 |
Times cited |
38 |
Open Access |
|
|
| |
Notes |
; The authors want to express their thanks to the VITO personnel for their continuous support, especially B. Molenberghs, W. Doyen, H. Beckers (Separation and Conversion Technology, VITO), R. Kemps, M. Mertens, I. Thijs, M. Schoeters, W. Bouwen and J. Cooymans (Materials Department, VITO). C. Buysse thankfully acknowledges a PhD scholarship provided by VITO and the University of Antwerp. This work is performed in the framework of the German Helmholtz Alliance Project “MEM-BRAIN”, aiming at the development of gas separation membranes for zero-emission fossil fuel power plants. ; |
Approved |
Most recent IF: 6.035; 2010 IF: 3.673 |
|
| |
Call Number |
UA @ admin @ c:irua:82008 |
Serial |
5950 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Smits, M.; Vanpachtenbeke, F.; Hauchecorne, B.; van Langenhove, H.; Demeestere, K.; Lenaerts, S. |
|
| |
Title |
Exhaust composition of a small diesel engine |
Type |
A2 Journal article |
| |
Year |
2012 |
Publication |
Communications in agricultural and applied biological sciences |
Abbreviated Journal |
|
|
| |
Volume |
77 |
Issue |
1 |
Pages |
85-88 |
|
| |
Keywords |
A2 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
|
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
|
Publication Date |
|
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1379-1176 |
ISBN |
|
Additional Links |
UA library record |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ admin @ c:irua:94166 |
Serial |
5949 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Hauchecorne, B.; Terrens, D.; Verbruggen, S.; Martens, J.A.; van Langenhove, H.; Demeestere, K.; Lenaerts, S. |
|
| |
Title |
Elucidating the photocatalytic degradation pathway of acetaldehyde : an FTIR in situ study under atmospheric conditions |
Type |
A1 Journal article |
| |
Year |
2011 |
Publication |
Applied catalysis : B : environmental |
Abbreviated Journal |
Appl Catal B-Environ |
|
| |
Volume |
106 |
Issue |
3/4 |
Pages |
630-638 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
| |
Abstract |
In this paper, new insights of the photocatalytic oxidation pathway of acetaldehyde are obtained by means of an in-house constructed FTIR in situ reactor. It is shown that there are generally three different intermediates present: acetic acid, formic acid and formaldehyde. By means of FTIR in situ spectroscopy, this study revealed that these intermediates are bound on the TiO2 surface in different ways, resulting in the presence of more intermediate species, such as molecularly adsorbed acetic acid, bidentate acetate, molecularly adsorbed formic acid, monodentate formate, bidentate formate, formaldehyde and dioxymethylene. Furthermore, spectroscopic evidence is obtained concerning the formation of 3-hydroxybutanal and crotonaldehyde upon adsorption of acetaldehyde on TiO2 prior to UV illumination. The presented results thus give new insights in the photocatalytic oxidation pathway of acetaldehyde. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000294092400042 |
Publication Date |
2011-06-28 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0926-3373 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
9.446 |
Times cited |
46 |
Open Access |
|
|
| |
Notes |
; The authors wish to thank the University of Antwerp for the funding of this research. ; |
Approved |
Most recent IF: 9.446; 2011 IF: 5.625 |
|
| |
Call Number |
UA @ admin @ c:irua:92433 |
Serial |
5948 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Delabie, L.; Honoré, M.; Lenaerts, S.; Huyberechts, G.; Roggen, J.; Maes, G. |
|
| |
Title |
The effect of sintering and Pd-doping on the conversion of CO to CO2 on SnO2 gas sensor materials |
Type |
A1 Journal article |
| |
Year |
1997 |
Publication |
Sensors And Actuators B-Chemical |
Abbreviated Journal |
Sensor Actuat B-Chem |
|
| |
Volume |
44 |
Issue |
|
Pages |
446-451 |
|
| |
Keywords |
A1 Journal article |
|
| |
Abstract |
The principal aim of this work is to study the effect of the processes of sintering and Pd doping of SnO2 gas sensor materials on the conversion of CO to CO2. For this purpose, the gas phase above screen printed sensor material is investigated using FTIR spectroscopy, while surface area, porosity and particle size measurements are performed on the SnO2 powders. During sintering, larger agglomerates of primary particles are formed, which results in a larger conversion degree of CO. The effect of Pd doping of the tin dioxide film on the CO conversion is more pronounced. The transformation of CO starts at a lower temperature and the conversion degree increases remarkably. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000071717900035 |
Publication Date |
2002-07-25 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0925-4005 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles; WoS full record; WoS citing articles |
|
| |
Impact Factor |
5.401 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 5.401; 1997 IF: 0.858 |
|
| |
Call Number |
UA @ admin @ c:irua:82017 |
Serial |
5947 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Smits, M.; Huygh, D.; Craeye, B.; Lenaerts, S. |
|
| |
Title |
Effect of process parameters on the photocatalytic soot degradation on self-cleaning cementitious materials |
Type |
A1 Journal article |
| |
Year |
2014 |
Publication |
Catalysis today |
Abbreviated Journal |
Catal Today |
|
| |
Volume |
230 |
Issue |
|
Pages |
250-255 |
|
| |
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL); Energy and Materials in Infrastructure and Buildings (EMIB) |
|
| |
Abstract |
Soot deposition has the negative ability to devalue the aesthetic appearance of buildings. Titanium dioxide applied on the building material is one way to counteract this problem as it provides air-purifying and self-cleaning properties due to its photocatalytic activity. In literature, photocatalytic soot oxidation was described, but until now, little information was available about the influence of process parameters on the photocatalytic degradation efficiency. The influence of three process parameters was tested in this study, namely TiO2 concentration, soot concentration and water-to-cement ratio (WIC-ratio) of the mortar substrates. The results revealed 50 mu gTiO(2) cm(-2) is better to use on the cementitious materials than 250 mu gTiO(2) cm(-2). The soot concentrations occurring in real-world situations will not inhibit the photocatalyst to be activated by light. Furthermore, the photonic efficiency increases slightly for lower WIC-ratios. This can be of interest for structural building applications, since a lower WIC-ratio results in a lower porosity of the samples and consequently in an increase in mortar strength. (C) 2013 Elsevier B.V. All rights reserved. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000333800300039 |
Publication Date |
2013-10-31 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0920-5861 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
4.636 |
Times cited |
14 |
Open Access |
|
|
| |
Notes |
; This work was supported by a PhD grant (M. Smits) from the University of Antwerp. We would like to thank T. Tytgat for the scientific discussion and Evonik for delivering the materials used in the experiments. ; |
Approved |
Most recent IF: 4.636; 2014 IF: 3.893 |
|
| |
Call Number |
UA @ admin @ c:irua:117142 |
Serial |
5946 |
|
| Permanent link to this record |
