| Records |
| Author |
Jovanović, Z.; Gauquelin, N.; Koster, G.; Rubio-Zuazo, J.; Ghosez, P.; Verbeeck, J.; Suvorov, D.; Spreitzer, M. |
| Title |
Simultaneous heteroepitaxial growth of SrO (001) and SrO (111) during strontium-assisted deoxidation of the Si (001) surface |
Type |
A1 Journal article |
Year  |
2020 |
Publication |
Rsc Advances |
Abbreviated Journal |
Rsc Adv |
| Volume |
10 |
Issue |
52 |
Pages |
31261-31270 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
Epitaxial integration of transition-metal oxides with silicon brings a variety of functional properties to the well-established platform of electronic components. In this process, deoxidation and passivation of the silicon surface are one of the most important steps, which in our study were controlled by an ultra-thin layer of SrO and monitored by using transmission electron microscopy (TEM), electron energy-loss spectroscopy (EELS), synchrotron X-ray diffraction (XRD) and reflection high energy electron diffraction (RHEED) methods. Results revealed that an insufficient amount of SrO leads to uneven deoxidation of the silicon surface<italic>i.e.</italic>formation of pits and islands, whereas the composition of the as-formed heterostructure gradually changes from strontium silicide at the interface with silicon, to strontium silicate and SrO in the topmost layer. Epitaxial ordering of SrO, occurring simultaneously with silicon deoxidation, was observed. RHEED analysis has identified that SrO is epitaxially aligned with the (001) Si substrate both with SrO (001) and SrO (111) out-of-plane directions. This observation was discussed from the point of view of SrO desorption, SrO-induced deoxidation of the Si (001) surface and other interfacial reactions as well as structural ordering of deposited SrO. Results of the study present an important milestone in understanding subsequent epitaxial integration of functional oxides with silicon using SrO. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000566579400025 |
Publication Date |
2020-08-24 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2046-2069 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
3.9 |
Times cited |
1 |
Open Access |
OpenAccess |
| Notes |
Vlaamse regering, Hercules Fund ; Ministarstvo Prosvete, Nauke i Tehnološkog Razvoja, III 45006 ; Javna Agencija za Raziskovalno Dejavnost RS, J2-9237 P2-0091 ; Fonds Wetenschappelijk Onderzoek, G.0044.13N ; Ministerio de Ciencia, Innovación y Universidades; Universiteit Antwerpen, GOA project Solarpaint ; F.R.S.-FNRS, PDR project PROMOSPAN ; Consejo Superior de Investigaciones Cientificas; University of Liège, ARC project AIMED ; Ministry of Education, Science and Sport, M.ERA-NET project SIOX ; |
Approved |
Most recent IF: 3.9; 2020 IF: 3.108 |
| Call Number |
EMAT @ emat @c:irua:172059 |
Serial |
6416 |
| Permanent link to this record |
| |
|
| |
| Author |
Grubova, I.Y.; Surmeneva, M.A.; Surmenev, R.A.; Neyts, E.C. |
| Title |
Effect of van der Waals interactions on the adhesion strength at the interface of the hydroxyapatite-titanium biocomposite : a first-principles study |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
RSC advances |
Abbreviated Journal |
|
| Volume |
10 |
Issue |
62 |
Pages |
37800-37805 |
| Keywords |
A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
| Abstract |
Hydroxyapatite (HAP) is frequently used as biocompatible coating on Ti-based implants. In this context, the HAP-Ti adhesion is of crucial importance. Here, we report ab initio calculations to investigate the influence of Si incorporation into the amorphous calcium-phosphate (a-HAP) structure on the interfacial bonding mechanism between the a-HAP coating and an amorphous titanium dioxide (a-TiO2) substrate, contrasting two different density functionals: PBE-GGA, and DFT-D3, which are capable of describing the influence of the van der Waals (vdW) interactions. In particular, we discuss the effect of dispersion on the work of adhesion (W-ad), equilibrium geometries, and charge density difference (CDD). We find that replacement of P by Si in a-HAP (a-Si-HAP) with the creation of OH vacancies as charge compensation results in a significant increase in the bond strength between the coating and substrate in the case of using the PBE-GGA functional. However, including the vdW interactions shows that these forces considerably contribute to the W-ad. We show that the difference (W-ad – W-ad(vdW)) is on average more than 1.1 J m(-2) and 0.5 J m(-2) for a-HAP/a-TiO2 and a-Si-HAP/a-TiO2, respectively. These results reveal that including vdW interactions is essential for accurately describing the chemical bonding at the a-HAP/a-TiO2 interface. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000583523300025 |
Publication Date |
2020-10-14 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
|
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
|
Times cited |
|
Open Access |
|
| Notes |
; The authors gratefully acknowledge financial support from the Russian president's grant MK-330.2020.8 and BOF Fellowships for International Joint PhD students funded by University of Antwerp (UAntwerp, project number 32545). The work was carried out at Tomsk Polytechnic University within the framework of Tomsk Polytechnic University Competitiveness Enhancement Program grant and in part using the Turing HPC infrastructure of the CalcUA core facility of the UAntwerp, a division of the Flemish Supercomputer Centre (VSC), funded by the Hercules Foundation, the Flemish Government (department EWI) and the UAntwerp, Belgium. ; |
Approved |
Most recent IF: NA |
| Call Number |
UA @ admin @ c:irua:173603 |
Serial |
6499 |
| Permanent link to this record |
| |
|
| |
| Author |
Bafekry, A.; Nguyen, C., V; Goudarzi, A.; Ghergherehchi, M.; Shafieirad, M. |
| Title |
Investigation of strain and doping on the electronic properties of single layers of C₆N₆ and C₆N₈: a first principles study |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Rsc Advances |
Abbreviated Journal |
Rsc Adv |
| Volume |
10 |
Issue |
46 |
Pages |
27743-27751 |
| Keywords |
A1 Journal article; Condensed Matter Theory (CMT) |
| Abstract |
In this work, by performing first-principles calculations, we explore the effects of various atom impurities on the electronic and magnetic properties of single layers of C(6)N(6)and C6N8. Our results indicate that atom doping may significantly modify the electronic properties. Surprisingly, doping Cr into a holey site of C(6)N(6)monolayer was found to exhibit a narrow band gap of 125 meV upon compression strain, considering the spin-orbit coupling effect. Also, a C atom doped in C(6)N(8)monolayer shows semi-metal nature under compression strains larger than -2%. Our results propose that Mg or Ca doped into strained C(6)N(6)may exhibit small band gaps in the range of 10-30 meV. In addition, a magnetic-to-nonmagnetic phase transition can occur under large tensile strains in the Ca doped C(6)N(8)monolayer. Our results highlight the electronic properties and magnetism of C(6)N(6)and C(6)N(8)monolayers. Our results show that the electronic properties can be effectively modified by atom doping and mechanical strain, thereby offering new possibilities to tailor the electronic and magnetic properties of C(6)N(6)and C(6)N(8)carbon nitride monolayers. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000553911800053 |
Publication Date |
2020-07-24 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2046-2069 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
3.9 |
Times cited |
11 |
Open Access |
|
| Notes |
; This work was supported by the National Research Foundation of Korea (NRF) grant funded by the Korean government (MSIT) (NRF-2017R1A2B2011989). ; |
Approved |
Most recent IF: 3.9; 2020 IF: 3.108 |
| Call Number |
UA @ admin @ c:irua:172111 |
Serial |
6553 |
| Permanent link to this record |
| |
|
| |
| Author |
Bafekry, A.; Shojai, F.; Hoat, D.M.; Shahrokhi, M.; Ghergherehchi, M.; Nguyen, C. |
| Title |
The mechanical, electronic, optical and thermoelectric properties of two-dimensional honeycomb-like of XSb (X = Si, Ge, Sn) monolayers: a first-principles calculations |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Rsc Advances |
Abbreviated Journal |
Rsc Adv |
| Volume |
10 |
Issue |
51 |
Pages |
30398-30405 |
| Keywords |
A1 Journal article; Condensed Matter Theory (CMT) |
| Abstract |
Herein, by using first-principles calculations, we demonstrate a two-dimensional (2D) of XSb (X = Si, Ge, and Sn) monolayers that have a honey-like crystal structure. The structural, mechanical, electronic, thermoelectric efficiency, and optical properties of XSb monolayers are studied.Ab initiomolecular dynamic simulations and phonon dispersion calculations suggests their good thermal and dynamical stabilities. The mechanical properties of XSb monolayers shows that the monolayers are considerably softer than graphene, and their in-plane stiffness decreases from SiSb to SnSb. Our results shows that the single layers of SiSb, GeSb and SnSb are semiconductor with band gap of 1.48, 0.77 and 0.73 eV, respectively. The optical analysis illustrate that the first absorption peaks of the SiSb, GeSb and SnSb monolayers along the in-plane polarization are located in visible range of light which may serve as a promising candidate to design advanced optoelectronic devices. Thermoelectric properties of the XSb monolayers, including Seebeck coefficient, electrical conductivity, electronic thermal conductivity, power factor and figure of merit are calculated as a function of doping level at temperatures of 300 K and 800 K. Between the studied two-dimensional materials (2DM), SiSb single layer may be the most promising candidate for application in the thermoelectric generators. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000561344000009 |
Publication Date |
2020-08-17 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2046-2069 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
3.9 |
Times cited |
2 |
Open Access |
|
| Notes |
; This work was supported by the National Research Foundation of Korea (NRF) grant funded by the Korea government (MSIT) (NRF-2017R1A2B2011989). ; |
Approved |
Most recent IF: 3.9; 2020 IF: 3.108 |
| Call Number |
UA @ admin @ c:irua:172074 |
Serial |
6624 |
| Permanent link to this record |
| |
|
| |
| Author |
Bafekry, A.; Shojaei, F.; Obeid, M.M.; Ghergherehchi, M.; Nguyen, C.; Oskouian, M. |
| Title |
Two-dimensional silicon bismotide (SiBi) monolayer with a honeycomb-like lattice: first-principles study of tuning the electronic properties |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Rsc Advances |
Abbreviated Journal |
Rsc Adv |
| Volume |
10 |
Issue |
53 |
Pages |
31894-31900 |
| Keywords |
A1 Journal article; Condensed Matter Theory (CMT) |
| Abstract |
Using density functional theory, we investigate a novel two-dimensional silicon bismotide (SiBi) that has a layered GaSe-like crystal structure.Ab initiomolecular dynamic simulations and phonon dispersion calculations suggest its good thermal and dynamical stability. The SiBi monolayer is a semiconductor with a narrow indirect bandgap of 0.4 eV. Our results show that the indirect bandgap decreases as the number of layers increases, and when the number of layers is more than six layers, direct-to-indirect bandgap switching occurs. The SiBi bilayer is found to be very sensitive to an E-field. The bandgap monotonically decreases in response to uniaxial and biaxial compressive strain, and reaches 0.2 eV at 5%, while at 6%, the semiconductor becomes a metal. For both uniaxial and biaxial tensile strains, the material remains a semiconductor and indirect-to-direct bandgap transition occurs at a strain of 3%. Compared to a SiBi monolayer with a layer thickness of 4.89 angstrom, the bandgap decreases with either increasing or decreasing layer thickness, and at a thicknesses of 4.59 to 5.01 angstrom, the semiconductor-to-metal transition happens. In addition, under pressure, the semiconducting character of the SiBi bilayer with a 0.25 eV direct bandgap is preserved. Our results demonstrate that the SiBi nanosheet is a promising candidate for designing high-speed low-dissipation devices. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000565206400027 |
Publication Date |
2020-09-02 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2046-2069 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
3.9 |
Times cited |
8 |
Open Access |
|
| Notes |
; This work was supported by the National Research Foundation of Korea (NRF) grant, funded by the Korea government (MSIT) (NRF-2017R1A2B2011989). ; |
Approved |
Most recent IF: 3.9; 2020 IF: 3.108 |
| Call Number |
UA @ admin @ c:irua:172045 |
Serial |
6644 |
| Permanent link to this record |
| |
|
| |
| Author |
González-Rubio, G.; Mosquera, J.; Kumar, V.; Pedrazo-Tardajos, A.; Llombart, P.; Solís, D.M.; Lobato, I.; Noya, E.G.; Guerrero-Martínez, A.; Taboada, J.M.; Obelleiro, F.; MacDowell, L.G.; Bals, S.; Liz-Marzán, L.M. |
| Title |
Micelle-directed chiral seeded growth on anisotropic gold nanocrystals |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Science |
Abbreviated Journal |
Science |
| Volume |
368 |
Issue |
368 |
Pages |
1472-1477 |
| Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
| Abstract |
Surfactant-assisted seeded growth of metal nanoparticles (NPs) can be engineered to produce anisotropic gold nanocrystals with high chiroptical activity through the templating effect of chiral micelles formed in the presence of dissymmetric cosurfactants. Mixed micelles adsorb on gold nanorods, forming quasihelical patterns that direct seeded growth into NPs with pronounced morphological and optical handedness. Sharp chiral wrinkles lead to chiral plasmon modes with high dissymmetry factors (~0.20). Through variation of the dimensions of chiral wrinkles, the chiroptical properties can be tuned within the visible and near-infrared electromagnetic spectrum. The micelle-directed mechanism allows extension to other systems, such as the seeded growth of chiral platinum shells on gold nanorods. This approach provides a reproducible, simple, and scalable method toward the fabrication of NPs with high chiral optical activity. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000545264600040 |
Publication Date |
2020-06-26 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0036-8075 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
56.9 |
Times cited |
187 |
Open Access |
OpenAccess |
| Notes |
L.M.L.-M. acknowledges funding from the European Research Council (ERC AdG No. 787510). G.G.-R. and J.M. thanks the Spanish MICIU for FPI (BES-2014-068972) and Juan de la Cierva-fellowships (FJCI-2015-25080). S.B., L.M.L.-M., V.K, and A.P.- T. acknowledge financial support from the European Commission under the Horizon 2020 Programme by means of the grant agreement No. 731019 (EUSMI) and the ERC Consolidator Grant No. 815128 (REALNANO). J.M.T and F.O acknowledge financial support from the Spanish MICIU (Grants TEC2017-85376-C2-1-R, TEC2017-85376-C2-2-R), as well as from the ERDF and the Galician Regional Government as part of the agreement for funding the Atlantic Research Center for Information and Communication Technologies (AtlantTIC). AG-M acknowledges financial support from the Spanish MICIU (Grant RTI2018-095844-BI00), EGN and LGM acknowledge funds from the Spanish MICIU (Grant No. FIS2017- 89361-C3-2-P), as well as the use of the Mare-Nostrum supercomputer and the technical support provided by Barcelona Supercomputing Center from the Spanish Network of Supercomputing (Grants QCM-2018-3-0039 and QCM-2019-1-0038). This work was performed under the Maria de Maeztu Units of Excellence Program from the Spanish State 13 Research Agency – Grant No. MDM-2017-0720.; sygma |
Approved |
Most recent IF: 56.9; 2020 IF: 37.205 |
| Call Number |
EMAT @ emat @c:irua:170137 |
Serial |
6391 |
| Permanent link to this record |
| |
|
| |
| Author |
van der Snickt, G.; Dooley, K.A.; Sanyova, J.; Dubois, H.; Delaney, J.K.; Gifford, E.M.; Legrand, S.; Laquiere, N.; Janssens, K. |
| Title |
Dual mode standoff imaging spectroscopy documents the painting process of the Lamb of God in the Ghent Altarpiece by J. and H. Van Eyck |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Science Advances |
Abbreviated Journal |
|
| Volume |
6 |
Issue |
31 |
Pages |
eabb3379 |
| Keywords |
A1 Journal article; Engineering sciences. Technology; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Antwerp Cultural Heritage Sciences (ARCHES) |
| Abstract |
The ongoing conservation treatment program of the Ghent Altarpiece by Hubert and Jan Van Eyck, one of the iconic paintings of the west, has revealed that the designs of the paintings were changed several times, first by the original artists, and then during later restorations. The central motif, The Lamb of God, representing Christ, plays an essential iconographic role, and its depiction is important. Because of the prevalence of lead white, it was not possible to visualize the Van Eycks' original underdrawing of the Lamb, their design changes, and the overpaint by later restorers with a single spectral imaging modality. However, by using elemental (x-ray fluorescence) and molecular (infrared reflectance) imaging spectroscopies, followed by analysis of the resulting data cubes, the necessary chemical contrast could be achieved. In this way, the two complementary modalities provided a more complete picture of the development and changes made to the Lamb. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000556543100033 |
Publication Date |
2020-07-29 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2375-2548 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
13.6 |
Times cited |
|
Open Access |
|
| Notes |
; This research was part of the activities of the Chair on Advanced Imaging Techniques for the Arts, established by the Baillet Latour fund. In addition, it was supported by the Belgian Science Policy Office (Project MO/39/011) and the Gieskes-Strijbis fund. We are also indebted to the BOF-GOA SOLARPaint project of the University of Antwerp Research Council and to FWO (Brussels) projects G056619N and G054719N. J.K.D. and K.A.D. acknowledge support from the National Gallery of Art. ; |
Approved |
Most recent IF: 13.6; 2020 IF: NA |
| Call Number |
UA @ admin @ c:irua:171270 |
Serial |
6494 |
| Permanent link to this record |
| |
|
| |
| Author |
Monico, L.; Cartechini, L.; Rosi, F.; Chieli, A.; Grazia, C.; De Meyer, S.; Nuyts, G.; Vanmeert, F.; Janssens, K.; Cotte, M.; De Nolf, W.; Falkenberg, G.; Sandu, I.C.A.; Tveit, E.S.; Mass, J.; De Freitas, R.P.; Romani, A.; Miliani, C. |
| Title |
Probing the chemistry of CdS paints in The Scream by in situ noninvasive spectroscopies and synchrotron radiation x-ray techniques |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Science Advances |
Abbreviated Journal |
|
| Volume |
6 |
Issue |
20 |
Pages |
eaay3514 |
| Keywords |
A1 Journal article; Engineering sciences. Technology; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation) |
| Abstract |
The degradation of cadmium sulfide (CdS)-based oil paints is a phenomenon potentially threatening the iconic painting The Scream (ca. 1910) by Edvard Munch (Munch Museum, Oslo) that is still poorly understood. Here, we provide evidence for the presence of cadmium sulfate and sulfites as alteration products of the original CdS-based paint and explore the external circumstances and internal factors causing this transformation. Macroscale in situ noninvasive spectroscopy studies of the painting in combination with synchrotron-radiation x-ray microspectroscopy investigations of a microsample and artificially aged mock-ups show that moisture and mobile chlorine compounds are key factors for promoting the oxidation of CdS, while light (photodegradation) plays a less important role. Furthermore, under exposure to humidity, parallel/secondary reactions involving dissolution, migration through the paint, and recrystallization of water-soluble phases of the paint are associated with the formation of cadmium sulfates. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000533573300009 |
Publication Date |
2020-05-16 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2375-2548 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
13.6 |
Times cited |
4 |
Open Access |
|
| Notes |
; The research was financially supported by the European research project IPERION-CH, funded by the European Commission, H2020-INFRAIA-2014-2015 (grant agreement no. 654028); the project AMIS, within the program Dipartimenti di Eccellenza 2018-2022 (funded by MIUR and University of Perugia); and the program “Ricerca di Base 2017” (funded by University of Perugia). S.D.M. and K.J. acknowledge the GOA Project SolarPaint from the University of Antwerp Research Council and projects G056619N and G054719N from FWO (Brussels). F.V. and K.J. acknowledge support from Interreg Project Smart*Light and thank BELSPO (Brussels) for financial support via FED-tWIN mandate PRF055. L.M. acknowledges the Erasmus+ program (Staff Mobility for training, A. Y. 2018 to 2019) of the European Commission. In situ noninvasive analyses were performed using the European MOLAB platform, which is financially supported by the European project IPERION-CH. For the beamtime grants received, the authors thank the ESRF-ID21 beamline (experiment nos. HG32, HG64, and HG95), DESY-P06 beamline, a member of the Helmholtz Association HGF (experiment nos. I-20130221 EC and I-20160126 EC), and the project CALIPSOplus under the Grant Agreement 730872 from the EU Framework Programme for Research and Innovation HORIZON 2020. ; |
Approved |
Most recent IF: 13.6; 2020 IF: NA |
| Call Number |
UA @ admin @ c:irua:169519 |
Serial |
6585 |
| Permanent link to this record |
| |
|
| |
| Author |
Byrnes, I.; Lind, O.C.; Hansen, E.L.; Janssens, K.; Salbu, B. |
| Title |
Characterization of radioactive particles from the Dounreay nuclear reprocessing facility |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Science Of The Total Environment |
Abbreviated Journal |
Sci Total Environ |
| Volume |
727 |
Issue |
|
Pages |
138488-12 |
| Keywords |
A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation) |
| Abstract |
Radioactive particles originating from nuclear fuel reprocessing at the United Kingdom Atomic Energy Authority's Dounreay Facility were inadvertently released to the environment in the late 1950s to 1970s and have subsequently been found on site grounds and local beaches. Previous assessments of risk associated with encountering a particle have been based on conservative assumptions related to particle composition and speciation. To reduce uncertainties associated with environmental impact assessments from Dounreay particles, further characterization is relevant. Results of particles available for this study showed variation between Dounreay Fast Reactor (DFR) and Materials Test Reactor (MTR) particles, reflecting differences in fuel design, release scenarios, and subsequent environmental influence. Analyses of DFR particles showed they are small (100-300 mu m) and contain spatially correlated U and Nb. Molybdenum, part of the DFR fuel, was identified at atomic concentrations below 1%. Based on SR-based micrometer-scale X-ray Absorption Near Edge Structure spectroscopy (mu-XANES), U may be present as U (IV), and, based on a measured Nb/U atom ratio of similar to 2, stoichiometric considerations are commensurable with the presence of UNb2O7. The MTR particles were larger (740-2000 mu m) and contained U and Al inhomogeneously distributed. Neodymium (Nd) was identified in atomic concentrations of around 1-2%, suggesting it was part of the fuel design. The presence of U(IV) in MTR particles, as indicated by mu-XANES analysis, may be related to oxidation of particle surfaces, as could be expected due to corrosion of UAlx fuel particles in air. High U-235/U-238 atom ratios in individual DFR (3.2 +/- 0.8) and MTR (2.6 +/- 0.4) particles reflected the presence of highly enriched uranium. The DFR particles featured lower Cs-137 activity levels (2.00-9.58 kBq/particle) than the MTR (43.2-641 kBq Cs-137/particle) particles. The activities of the dose contributing radionuclides Sr-90/Y-90 were proportional to Cs-137 (Sr-90/Cs-137 activity ratio approximate to 0.8) and particle activities were roughly proportional to the size. Based on direct beta measurements, gamma spectrometry, and the VARSKIN6 model, contact dose rates were calculated to be approximately 74 mGy/h for the highest activity MTR particle, in agreement with previously published estimates. (C) 2020 The Authors. Published by Elsevier B.V. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000537414400014 |
Publication Date |
2020-04-07 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0048-9697 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
9.8 |
Times cited |
1 |
Open Access |
|
| Notes |
; This study has been funded by the Research Council of Norway through its Centre of Excellence (CoE) funding scheme (Project No. 223268/F50). The authors are grateful to the Scottish Environmental Protection Agency for providing the samples examined in this study and Deutsches Elektronen-Synchrotron (DESY) for granting beamtime at HASYLAB BL. The authors would like to thank Prof. D.H. Oughton for fruitful discussions on dosimetry, Dr. K. Proost for assistance with micro-XANES measurements, Dr. T. Gavfert for assistance with calibration of the Canberra SPAB15 instrument, and Dr. E. Reinoso-Maset for support on the Bruker M4 Tornado mu-XRF. The authors also thank Karl Andreas Jensen for guidance and support on ICP-MS. Finally, the authors express gratitude to Dr. D. Hamby and the RAMP organization for providing access to the VARSKIN6 code. ; |
Approved |
Most recent IF: 9.8; 2020 IF: 4.9 |
| Call Number |
UA @ admin @ c:irua:170154 |
Serial |
6467 |
| Permanent link to this record |
| |
|
| |
| Author |
Do, M.T.; Gauquelin, N.; Nguyen, M.D.; Wang, J.; Verbeeck, J.; Blom, F.; Koster, G.; Houwman, E.P.; Rijnders, G. |
| Title |
Interfacial dielectric layer as an origin of polarization fatigue in ferroelectric capacitors |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Scientific Reports |
Abbreviated Journal |
Sci Rep-Uk |
| Volume |
10 |
Issue |
1 |
Pages |
7310 |
| Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
| Abstract |
Origins of polarization fatigue in ferroelectric capacitors under electric field cycling still remain unclear. Here, we experimentally identify origins of polarization fatigue in ferroelectric PbZr0.52Ti0.48O3 (PZT) thin-film capacitors by investigating their fatigue behaviours and interface structures. The PZT layers are epitaxially grown on SrRuO3-buffered SrTiO3 substrates by a pulsed laser deposition (PLD), and the capacitor top-electrodes are various, including SrRuO3 (SRO) made by in-situ PLD, Pt by in-situ PLD (Pt-inPLD) and ex-situ sputtering (Pt-sputtered). We found that fatigue behaviour of the capacitor is directly related to the top-electrode/PZT interface structure. The Pt-sputtered/PZT/SRO capacitor has a thin defective layer at the top interface and shows early fatigue while the Pt-inPLD/PZT/SRO and SRO/PZT/SRO capacitor have clean top-interfaces and show much more fatigue resistance. The defective dielectric layer at the Pt-sputtered/PZT interface mainly contains carbon contaminants, which form during the capacitor ex-situ fabrication. Removal of this dielectric layer significantly delays the fatigue onset. Our results clearly indicate that dielectric layer at ferroelectric capacitor interfaces is the main origin of polarization fatigue, as previously proposed in the charge injection model. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000559953800003 |
Publication Date |
2020-04-30 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2045-2322 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
4.6 |
Times cited |
18 |
Open Access |
OpenAccess |
| Notes |
; The authors acknowledge the financial support of the Nederlandse Organisatie voor Wetenschappelijk Onderzoek through Grant No. F62.3.15559. ; |
Approved |
Most recent IF: 4.6; 2020 IF: 4.259 |
| Call Number |
EMAT @ emat @c:irua:169865 |
Serial |
6374 |
| Permanent link to this record |
| |
|
| |
| Author |
Reclusa, P.; Verstraelen, P.; Taverna, S.; Gunasekaran, M.; Pucci, M.; Pintelon, I.; Claes, N.; de Miguel-Pérez, D.; Alessandro, R.; Bals, S.; Kaushal, S.; Rolfo, C. |
| Title |
Improving extracellular vesicles visualization: From static to motion |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Scientific Reports |
Abbreviated Journal |
Sci Rep-Uk |
| Volume |
10 |
Issue |
10 |
Pages |
6494 |
| Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
| Abstract |
In the last decade extracellular vesicles (EVs) have become a hot topic. The findings on EVs content and effects have made them a major field of interest in cancer research. EVs, are able to be internalized through integrins expressed in parental cells, in a tissue specific manner, as a key step of cancer progression and pre-metastatic niche formation. However, this specificity might lead to new opportunities in cancer treatment by using EVs as devices for drug delivery. For future applications of EVs in cancer, improved protocols and methods for EVs isolation and visualization are required. Our group has put efforts on developing a protocol, able to track the EVs for in vivo internalization analysis. We showed, for the first time, the videos of labeled EVs uptake by living lung cancer cells. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000562145000002 |
Publication Date |
2020-04-16 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2045-2322 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
4.6 |
Times cited |
25 |
Open Access |
OpenAccess |
| Notes |
Marzia Pucci is supported by a “AIRC” (Associazione Italiana Ricerca sul Cancro) fellowship. “The Leica SP 8 (Hercules grant AUHA.15.12) microscope was funded by the Hercules Foundation of the Flemish Government.” DdM-P is funded by the University of Granada PhD grant and University of Granada international mobility grant 2018/19. |
Approved |
Most recent IF: 4.6; 2020 IF: 4.259 |
| Call Number |
EMAT @ emat @c:irua:169234 |
Serial |
6362 |
| Permanent link to this record |
| |
|
| |
| Author |
Bafekry, A.; Stampfl, C.; Peeters, F.M. |
| Title |
Dirac half-metallicity of thin PdCl₃ nanosheets : investigation of the effects of external fields, surface adsorption and defect engineering on the electronic and magnetic properties |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Scientific Reports |
Abbreviated Journal |
Sci Rep-Uk |
| Volume |
10 |
Issue |
1 |
Pages |
213-215 |
| Keywords |
A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT) |
| Abstract |
PdCl3 belongs to a novel class of Dirac materials with Dirac spin-gapless semiconducting characteristics. In this paper based, on first-principles calculations, we have systematically investigated the effect of adatom adsorption, vacancy defects, electric field, strain, edge states and layer thickness on the electronic and magnetic properties of PdCl3 (palladium trichloride). Our results show that when spin-orbital coupling is included, PdCl3 exhibits the quantum anomalous Hall effect with a non-trivial band gap of 24 meV. With increasing number of layers, from monolayer to bulk, a transition occurs from a Dirac half-metal to a ferromagnetic metal. On application of a perpendicular electrical field to bilayer PdCl3, we find that the energy band gap decreases with increasing field. Uniaxial and biaxial strain, significantly modifies the electronic structure depending on the strain type and magnitude. Adsorption of adatom and topological defects have a dramatic effect on the electronic and magnetic properties of PdCl3. In particular, the structure can become a metal (Na), half-metal (Be, Ca, Al, Ti, V, Cr, Fe and Cu with, respective, 0.72, 9.71, 7.14, 6.90, 9.71, 4.33 and 9.5 μB magnetic moments), ferromagnetic-metal (Sc, Mn and Co with 4.55, 7.93 and 2.0 μB), spin-glass semiconductor (Mg, Ni with 3.30 and 8.63 μB), and dilute-magnetic semiconductor (Li, K and Zn with 9.0, 9.0 and 5.80 μB magnetic moment, respectively). Single Pd and double Pd + Cl vacancies in PdCl3 display dilute-magnetic semiconductor characteristics, while with a single Cl vacancy, the material becomes a half-metal. The calculated optical properties of PdCl3 suggest it could be a good candidate for microelectronic and optoelectronics devices. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000562795700001 |
Publication Date |
2020-01-14 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2045-2322 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
4.6 |
Times cited |
29 |
Open Access |
|
| Notes |
; This work was supported by the Flemish Science Foundation (FWO-Vl). We are thankful for comments by Sevil Sarikurt from the department of physics in Dokuz Eylul University. In addition, we acknowledge OpenMX team for OpenMX code. ; |
Approved |
Most recent IF: 4.6; 2020 IF: 4.259 |
| Call Number |
UA @ admin @ c:irua:169751 |
Serial |
6483 |
| Permanent link to this record |
| |
|
| |
| Author |
Do, N.H.; Pham, H.H.; Le, T.M.; Lauwaert, J.; Diels, L.; Verberckmoes, A.; Do, N.H.N.; Tran, V.T.; Le, P.K. |
| Title |
The novel method to reduce the silica content in lignin recovered from black liquor originating from rice straw |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Scientific Reports |
Abbreviated Journal |
Sci Rep-Uk |
| Volume |
10 |
Issue |
1 |
Pages |
21263 |
| Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
Difficulties in the production of lignin from rice straw because of high silica content in the recovered lignin reduce its recovery yield and applications as bio-fuel and aromatic chemicals. Therefore, the objective of this study is to develop a novel method to reduce the silica content in lignin from rice straw more effectively and selectively. The method is established by monitoring the precipitation behavior as well as the chemical structure of precipitate by single-stage acidification at different pH values of black liquor collected from the alkaline treatment of rice straw. The result illustrates the significant influence of pH on the physical and chemical properties of the precipitate and the supernatant. The simple two-step acidification of the black liquor at pilot-scale by sulfuric acid 20w/v% is applied to recover lignin at pH 9 and pH 3 and gives a percentage of silica removal as high as 94.38%. Following the developed process, the high-quality lignin could be produced from abundant rice straw at the industrial-scale. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000608856300027 |
Publication Date |
2020-12-04 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2045-2322 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
4.6 |
Times cited |
|
Open Access |
|
| Notes |
|
Approved |
Most recent IF: 4.6; 2020 IF: 4.259 |
| Call Number |
UA @ admin @ c:irua:176054 |
Serial |
8655 |
| Permanent link to this record |
| |
|
| |
| Author |
Anaf, W.; Cabal, A.; Robbe, M.; Schalm, O. |
| Title |
Real-time wood behaviour : the use of strain gauges for preventive conservation applications |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Sensors |
Abbreviated Journal |
|
| Volume |
20 |
Issue |
1 |
Pages |
305 |
| Keywords |
A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Antwerp Cultural Heritage Sciences (ARCHES) |
| Abstract |
Within the heritage field, the application of strain gauges on wood surfaces is a little-explored but inexpensive and effective method to analyse the environmental appropriateness of rooms for the wooden heritage collections they contain. This contribution proposes a wood sensor connected to a data logger to identify short moments with an elevated risk of harm. Two experiments were performed to obtain insights pertaining to the applicability of wood sensors to evaluate preservation conditions. (1) The representativeness of strain gauges on dummies was tested for their use in evaluating the preservation conditions of a range of wooden objects exposed to the same environment. For this, three situations were mimicked: a bare wood surface, a wood surface covered with a preparation layer, and a wood surface covered with a preparation and varnish layer. (2) The usability of strain gauges to monitor the wood behaviour in real-time measurements was tested with a monitoring campaign of almost two years in a church where a new heating system was installed. The results of both experiments are promising, and the authors encourage a broader application of strain gauges in the heritage field. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000510493100305 |
Publication Date |
2020-01-06 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
|
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
|
Times cited |
|
Open Access |
|
| Notes |
; This research was funded by the Belgian Federal Public Planning Service Science Policy (BELSPO) under project number BR/132/A6/AIRCHECQ. ; |
Approved |
Most recent IF: NA |
| Call Number |
UA @ admin @ c:irua:166595 |
Serial |
6592 |
| Permanent link to this record |
| |
|
| |
| Author |
Rumyantseva, M.N.; Vladimirova, S.A.; Platonov, V.B.; Chizhov, A.S.; Batuk, M.; Hadermann, J.; Khmelevsky, N.O.; Gaskov, A.M. |
| Title |
Sub-ppm H2S sensing by tubular ZnO-Co3O4 nanofibers |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Sensors And Actuators B-Chemical |
Abbreviated Journal |
Sensor Actuat B-Chem |
| Volume |
307 |
Issue |
|
Pages |
127624 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
Tubular ZnO – Co3O4 nanofibers were co-electrospun from polymer solution containing zinc and cobalt acetates. Phase composition, cobalt electronic state and element distribution in the fibers were investigated by XRD, SEM, HRTEM, HAADF-STEM with EDX mapping, and XPS. Bare ZnO has high selective sensitivity to NO and NO2, while ZnO-Co3O4 composites demonstrate selective sensitivity to H2S in dry and humid air. This effect is discussed in terms of transformation of cobalt oxides into cobalt sulfides and change in the acidity of ZnO oxide surface upon cobalt doping. Reduction in response and recovery time is attributed to the formation of a tubular structure facilitating gas transport through the sensitive layer. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000508110400059 |
Publication Date |
2019-12-24 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0925-4005 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
5.401 |
Times cited |
|
Open Access |
Not_Open_Access |
| Notes |
This work was supported by RFBR grants No. 18-03-00091 and No. 18-03-00580. |
Approved |
Most recent IF: NA |
| Call Number |
EMAT @ emat @c:irua:166449 |
Serial |
6343 |
| Permanent link to this record |
| |
|
| |
| Author |
Pourbabak, S.; Verlinden, B.; Van Humbeeck, J.; Schryvers, D. |
| Title |
DSC cycling effects on phase transformation temperatures of micron and submicron grain Ni50.8Ti49.2 microwires |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Shape memory and superelasticity |
Abbreviated Journal |
|
| Volume |
|
Issue |
|
Pages |
1-10 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
The effect of thermal cycling parameters on the phase transformation temperatures of micron and submicron grain size recrystallized Ni-Ti microwires was investigated. The suppression of martensitic transformation by thermal cycling was found to enhance when combined with room temperature aging between the cycles and enhances even more when aged at elevated temperature of 100 degrees C. While aging at room temperature alone has no clear effect on the martensitic transformation, elevated temperature aging at 100 degrees C alone suppresses the martensitic transformation. All aforementioned effects were found to be stronger in large grain samples than in small grain samples. Martensitic transformation suppression in all cases was in line with the formation of Ni4Ti3 precursors in the form of < 111 & rang;(B2) Ni clusters as concluded from the observed diffuse intensity in the electron diffraction patterns revealing short-range ordering enhancement. Performing thermal cycling in some different temperature ranges to separate the effect of martensitic transformation and high temperature range of DSC cycling revealed that both high temperature- and martensitic transformation-included cycles enhance the short-range ordering. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000530232800001 |
Publication Date |
2020-05-04 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2199-384x; 2199-3858 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
|
Times cited |
1 |
Open Access |
Not_Open_Access |
| Notes |
; S.P. would like to thank the Flemish Science Foundation FWO for financial support under Project G.0366.15N. ; |
Approved |
Most recent IF: NA |
| Call Number |
UA @ admin @ c:irua:169514 |
Serial |
6492 |
| Permanent link to this record |
| |
|
| |
| Author |
Rafiaani, P.; Dikopoulou, Z.; Van Dael, M.; Kuppens, T.; Azadi, H.; Lebailly, P.; Van Passel, S. |
| Title |
Identifying Social Indicators for Sustainability Assessment of CCU Technologies: A Modified Multi-criteria Decision Making |
Type |
A1 Journal Article |
| Year |
2020 |
Publication |
Social Indicators Research |
Abbreviated Journal |
Soc Indic Res |
| Volume |
147 |
Issue |
1 |
Pages |
15-44 |
| Keywords |
A1 Journal Article; Engineering Management (ENM) ; |
| Abstract |
Carbon capture and utilization (CCU) technologies capture CO2 waste emissions and utilize them to generate new products (such as fuels, chemicals, and materials) with various environmental, economic, and social opportunities. As most of these CCU technologies are in the R&D stage, their technical and economic viability are examined with less attention to the social aspect which is an important pillar for a holistic sustainability assessment. The lack of systematic social impact research is mainly due to the difficulty of identifying and quantifying social aspects through the entire life cycle of products. We will fill this gap for CCU technologies and identify the main social indicators. A multi-criteria decision making tool: TOPSIS (technique for order of preference by similarity to ideal solution) was applied to empirically determine which indicators are more relevant for assessing the social impact of a company operating CCU activities within a European context. First, seeing that social impact categories are linked to key stakeholder groups, we considered workers, consumers, and local communities as relevant stakeholders. Second, the main social impact categories and their potential performance indicators associated to each group of stakeholders were listed using the United Nations Environment Program/Society of Environmental Toxicology and Chemistry (UNEP/SETAC) guidelines. In the third step, an online questionnaire was distributed to identify the main social categories and indicators for CCU, to which 33 European CCU experts responded. Finally, a modified TOPSIS was applied to rank the indicators based on their relevance. We found that the indicators related to “end of life responsibility” and “transparency” within a CCU company achieved the highest rank affecting the consumers group, whereas “fair salary” and “equal opportunities/discriminations” were determined as the most relevant impact categories for the workers. For the local community group, “secure living conditions” and “local employment” received the highest priority from the experts’ point of view. Furthermore, “health and safety” considerations were identified as one of the most important criteria affecting all three groups of stakeholders. The ranking list of the main social indicators identified in our study provides the basis for the next steps in the social sustainability assessment of CCU technologies; that is, data collection and impact assessment. Our outcomes can also be used to inform the producers regarding the most and least relevant social aspects of CCU so that the potential social impacts caused by their production activities can be improved or prevented. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000511863600002 |
Publication Date |
2019-07-06 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0303-8300 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
1.743 |
Times cited |
|
Open Access |
|
| Notes |
We would also like to thank James Morrison from the JamesEdits agency for proof reading and editing the article. |
Approved |
Most recent IF: NA |
| Call Number |
ENM @ enm @c:irua:166591 |
Serial |
6354 |
| Permanent link to this record |
| |
|
| |
| Author |
Erfurt, D.; Koida, T.; Heinemann, M.D.; Li, C.; Bertram, T.; Nishinaga, J.; Szyszka, B.; Shibata, H.; Klenk, R.; Schlatmann, R. |
| Title |
Impact of rough substrates on hydrogen-doped indium oxides for the application in CIGS devices |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Solar Energy Materials And Solar Cells |
Abbreviated Journal |
Sol Energ Mat Sol C |
| Volume |
206 |
Issue |
|
Pages |
110300 |
| Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
| Abstract |
Indium oxide based transparent conductive oxides (TCOs) are promising contact layers in solar cells due to their outstanding electrical and optical properties. However, when applied in Cu(In,Ga)Se-2 or Si-hetero-junction solar cells the specific roughness of the material beneath can affect the growth and the properties of the TCO. We investigated the electrical properties of hydrogen doped and hydrogen-tungsten co-doped indium oxides grown on rough Cu(In,Ga)Se-2 samples as well as on textured and planar glass. At sharp ridges and V-shaped valleys crack-shaped voids form inside the indium oxide films, which limit the effective electron mobility of the In2O3:H and In2O3:H,W thin films. This was found for films deposited by magnetron sputtering and reactive plasma deposition at several deposition parameters, before as well as after annealing and solid phase crystallization. This suggests universal behavior that will have a wide impact on solar cell devices. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000519653800038 |
Publication Date |
2019-11-29 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0927-0248 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
6.9 |
Times cited |
5 |
Open Access |
OpenAccess |
| Notes |
; This work was supported by the German Federal Ministry for Economic Affairs and Energy under contract number 0325762G (TCO4CIGS). The authors thank M. Hartig, K. Mayer-Stillrich, I. Dorbandt, B. Bunn, M. Kirsch for technical support. C. Li is grateful for financial support from Max Planck Society, Germany and technical support from the MPI FKF StEM group members. ; |
Approved |
Most recent IF: 6.9; 2020 IF: 4.784 |
| Call Number |
UA @ admin @ c:irua:168668 |
Serial |
6544 |
| Permanent link to this record |
| |
|
| |
| Author |
Celentano, G.; Rizzo, F.; Augieri, A.; Mancini, A.; Pinto, V.; Rufoloni, A.; Vannozzi, A.; MacManus-Driscoll, J.L.; Feighan, J.; Kursumovic, A.; Meledin, A.; Mayer, J.; Van Tendeloo, G. |
| Title |
YBa2Cu3O7−xfilms with Ba2Y(Nb,Ta)O6nanoinclusions for high-field applications |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Superconductor Science & Technology |
Abbreviated Journal |
Supercond Sci Tech |
| Volume |
33 |
Issue |
4 |
Pages |
044010 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
The structural and transport properties of YBa2Cu3O7−x films grown by pulsed laser deposition with mixed 2.5 mol% Ba2YTaO6 (BYTO) and 2.5 mol% Ba2YNbO6 (BYNO) double-perovskite secondary phases are investigated in an extended film growth rate, R = 0.02–1.8 nm s−1. The effect of R on the film microstructure analyzed by TEM techniques shows an evolution from sparse and straight to denser, thinner and splayed continuous columns, with mixed BYNO + BYTO (BYNTO) composition, as R increases from 0.02 nm s−1 to 1.2 nm s−1. This microstructure results in very efficient flux pinning at 77 K, leading to a remarkable improvement in the critical current density (J c) behaviour, with the maximum pinning force density F p(Max) = 13.5 GN m−3 and the irreversibility field in excess of 11 T. In this range, the magnetic field values at which the F p is maximized varies from 1 T to 5 T, being related to the BYNTO columnar density. The film deposited when R = 0.3 nm s−1 exhibits the best performances over the whole temperature and magnetic field ranges, achieving F p(Max) = 900 GN m−3 at 10 K and 12 T. At higher rates, R > 1.2 nm s−1, BYNTO columns show a meandering nature and are prone to form short nanorods. In addition, in the YBCO film matrix a more disordered structure with a high density of short stacking faults is observed. From the analysis of the F p(H, T) curves it emerges that in films deposited at the high R limit, the vortex pinning is no longer dominated by BYNTO columnar defects, but by a new mechanism showing the typical temperature scaling law. Even though this microstructure produces a limited improvement at 77 K, it exhibits a strong J c improvement at lower temperature with F p = 700 GN m−3 at 10 K, 12 T and 900 GN m−3 at 4.2 K, 18 T. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000525650500001 |
Publication Date |
2020-04-01 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0953-2048 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
3.6 |
Times cited |
|
Open Access |
OpenAccess |
| Notes |
This work was partially financially supported by EUROTAPES, a collaborative project funded by the European Commission’s Seventh Framework Program (FP7/2007–2013) under Grant Agreement No. 280432. This work has been partially carried out within the framework of the EUROfusion Consortium and has received funding from the Euratom programme 2014-2018 and 2019-2020 under grant agreement N° 633053. The views and opinions expressed herein do not necessarily reflect those of the European Commission. This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 823717 – ESTEEM3 (Nano-engineered YBCO Superconducting Tapes for High Field Applications, NESTApp). G. C. acknowledges the support of Michele De Angelis for XRD measurements and calculations. |
Approved |
Most recent IF: 3.6; 2020 IF: 2.878 |
| Call Number |
UA @ lucian @c:irua:168582 |
Serial |
6394 |
| Permanent link to this record |
| |
|
| |
| Author |
Kenawy, A.; Magnus, W.; Milošević, M.V.; Sorée, B. |
| Title |
Electronically tunable quantum phase slips in voltage-biased superconducting rings as a base for phase-slip flux qubits |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Superconductor Science & Technology |
Abbreviated Journal |
Supercond Sci Tech |
| Volume |
33 |
Issue |
12 |
Pages |
125002 |
| Keywords |
A1 Journal article; Condensed Matter Theory (CMT) |
| Abstract |
Quantum phase slips represent a coherent mechanism to couple flux states of a superconducting loop. Since their first direct observation, there have been substantial developments in building charge-insensitive quantum phase-slip circuits. At the heart of these devices is a weak link, often a nanowire, interrupting a superconducting loop. Owing to the very small cross-sectional area of such a nanowire, quantum phase slip rates in the gigahertz range can be achieved. Instead, here we present the use of a bias voltage across a superconducting loop to electrostatically induce a weak link, thereby amplifying the rate of quantum phase slips without physically interrupting the loop. Our simulations reveal that the bias voltage modulates the free energy barrier between subsequent flux states in a very controllable fashion, providing a route towards a phase-slip flux qubit with a broadly tunable transition frequency. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000577207000001 |
Publication Date |
2020-09-16 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0953-2048 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
3.6 |
Times cited |
4 |
Open Access |
|
| Notes |
; ; |
Approved |
Most recent IF: 3.6; 2020 IF: 2.878 |
| Call Number |
UA @ admin @ c:irua:172643 |
Serial |
6503 |
| Permanent link to this record |
| |
|
| |
| Author |
Surmenev, R.A.; Grubova, I.Y.; Neyts, E.; Teresov, A.D.; Koval, N.N.; Epple, M.; Tyurin, A.I.; Pichugin, V.F.; Chaikina, M.V.; Surmeneva, M.A. |
| Title |
Ab initio calculations and a scratch test study of RF-magnetron sputter deposited hydroxyapatite and silicon-containing hydroxyapatite coatings |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Surfaces and interfaces |
Abbreviated Journal |
|
| Volume |
21 |
Issue |
|
Pages |
|
| Keywords |
A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
| Abstract |
A crucial property for implants is their biocompatibility. To ensure biocompatibility, thin coatings of hydroxyapatite (HA) are deposited on the actual implant. In this study, we investigate the effects of the addition of silicate anions to the structure of hydroxyapatite coatings on their adhesion strength via a scratch test and ab initio calculations. We find that both the grain size and adhesion strength decrease with the increase in the silicon content in the HA coating (SiHA). The increase in the silicon content to 1.2 % in the HA coating leads to a decrease in the average crystallite size from 28 to 21 nm, and in the case of 4.6 %, it leads to the formation of an amorphous or nanocrystalline film. The decreases in the grain and crystallite sizes lead to peeling and destruction of the coating from the titanium substrate at lower loads. Further, our ab initio simulations demonstrate an increased number of molecular bonds at the amorphous SiHA-TiO2 interface. However, the experimental results revealed that the structure and grain size have more pronounced effects on the adhesion strength of the coatings. In conclusion, based on the results of the ab initio simulations and the experimental results, we suggest that the presence of Si in the form of silicate ions in the HA coating has a significant impact on the structure, grain size, and number of molecular bonds at the interface and on the adhesion strength of the SiHA coating to the titanium substrate. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000697616300009 |
Publication Date |
2020-10-02 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2468-0230 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
6.2 |
Times cited |
|
Open Access |
|
| Notes |
|
Approved |
Most recent IF: 6.2; 2020 IF: NA |
| Call Number |
UA @ admin @ c:irua:181685 |
Serial |
7400 |
| Permanent link to this record |
| |
|
| |
| Author |
Finizola e Silva, M.; Van Passel, S. |
| Title |
Climate-Smart Agriculture in the Northeast of Brazil: An Integrated Assessment of the Aquaponics Technology |
Type |
A1 Journal Article |
| Year |
2020 |
Publication |
Sustainability |
Abbreviated Journal |
Sustainability-Basel |
| Volume |
12 |
Issue |
9 |
Pages |
3734 |
| Keywords |
A1 Journal Article; aquaponics; Aquaponova; Brazil; semi-arid region; food insecurity; cost–benefit analysis; socio-economic approach; climate-smart agriculture; Engineering Management (ENM) ; |
| Abstract |
The purpose of this study is to determine if aquaponic systems can reduce food insecurity in the semi-arid regions of Brazil and generate income for the beneficiaries. Aquaponics is a potentially sustainable way to produce food based on gardening, hydroponics and aquaculture. A case study, based on a project called Aquaponova, was developed. The aquaponic systems currently used in the project are non-commercial and designed for households with limited resources. The data based on six existing systems within this project were used to compare the costs and the benefits. The cost–benefit analysis covers four scenarios and three financing options. The results show that aquaponic systems have a large potential and can reduce food insecurity in semi-arid regions while generating income for the beneficiaries. Even if the system only produces 40% of the total estimated production, the system will still be feasible. However, the low opportunity cost of labour is an essential factor for obtaining these positive results. Moreover, the social benefits, such as a community spirit and the health benefits of the system, should not be underestimated. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000537476200232 |
Publication Date |
2020-05-05 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2071-1050 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
3.9 |
Times cited |
|
Open Access |
|
| Notes |
We would like to express our gratitude to Francisco Fechine Borges who introduced Maíra Finizola e Silva the basics of aquaponics and gave her the opportunity to base her research on the data from the Aquaponova project. We would also like to thank the participants of the 2nd LA SDEWES conference in Buenos Aires (9–12 February 2020) for the useful comments and suggestions. |
Approved |
Most recent IF: 3.9; 2020 IF: 1.789 |
| Call Number |
ENM @ enm @c:irua:170074 |
Serial |
6382 |
| Permanent link to this record |
| |
|
| |
| Author |
Shi, P.; Ratkowsky, D.A.; Gielis, J. |
| Title |
The generalized Gielis geometric equation and its application |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Symmetry-Basel |
Abbreviated Journal |
Symmetry-Basel |
| Volume |
12 |
Issue |
4 |
Pages |
645-10 |
| Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
Many natural shapes exhibit surprising symmetry and can be described by the Gielis equation, which has several classical geometric equations (for example, the circle, ellipse and superellipse) as special cases. However, the original Gielis equation cannot reflect some diverse shapes due to limitations of its power-law hypothesis. In the present study, we propose a generalized version by introducing a link function. Thus, the original Gielis equation can be deemed to be a special case of the generalized Gielis equation (GGE) with a power-law link function. The link function can be based on the morphological features of different objects so that the GGE is more flexible in fitting the data of the shape than its original version. The GGE is shown to be valid in depicting the shapes of some starfish and plant leaves. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000540222200156 |
Publication Date |
2020-04-21 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2073-8994 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
2.7 |
Times cited |
4 |
Open Access |
|
| Notes |
; This research was funded by the Jiangsu Government Scholarship for Overseas Studies (grant number: JS-2018-038). ; |
Approved |
Most recent IF: 2.7; 2020 IF: 1.457 |
| Call Number |
UA @ admin @ c:irua:168141 |
Serial |
6526 |
| Permanent link to this record |
| |
|
| |
| Author |
Huang, W.; Li, Y.; Niklas, K.J.; Gielis, J.; Ding, Y.; Cao, L.; Shi, P. |
| Title |
A superellipse with deformation and its application in describing the cross-sectional shapes of a square bamboo |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Symmetry-Basel |
Abbreviated Journal |
Symmetry-Basel |
| Volume |
12 |
Issue |
12 |
Pages |
2073 |
| Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
Many cross-sectional shapes of plants have been found to approximate a superellipse rather than an ellipse. Square bamboos, belonging to the genus Chimonobambusa (Poaceae), are a group of plants with round-edged square-like culm cross sections. The initial application of superellipses to model these culm cross sections has focused on Chimonobambusa quadrangularis (Franceschi) Makino. However, there is a need for large scale empirical data to confirm this hypothesis. In this study, approximately 750 cross sections from 30 culms of C. utilis were scanned to obtain cross-sectional boundary coordinates. A superellipse exhibits a centrosymmetry, but in nature the cross sections of culms usually deviate from a standard circle, ellipse, or superellipse because of the influences of the environment and terrain, resulting in different bending and torsion forces during growth. Thus, more natural cross-sectional shapes appear to have the form of a deformed superellipse. The superellipse equation with a deformation parameter (SEDP) was used to fit boundary data. We find that the cross-sectional shapes (including outer and inner rings) of C. utilis can be well described by SEDP. The adjusted root-mean-square error of SEDP is smaller than that of the superellipse equation without a deformation parameter. A major finding is that the cross-sectional shapes can be divided into two types of superellipse curves: hyperellipses and hypoellipses, even for cross sections from the same culm. There are two proportional relationships between ring area and the product of ring length and width for both the outer and inner rings. The proportionality coefficients are significantly different, as a consequence of the two different superellipse types (i.e., hyperellipses and hypoellipses). The difference in the proportionality coefficients between hyperellipses and hypoellipses for outer rings is greater than that for inner rings. This work informs our understanding and quantifying of the longitudinal deformation of plant stems for future studies to assess the influences of the environment on stem development. This work is also informative for understanding the deviation of natural shapes from a strict rotational symmetry. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000602546300001 |
Publication Date |
2020-12-15 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2073-8994 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
2.7 |
Times cited |
|
Open Access |
|
| Notes |
|
Approved |
Most recent IF: 2.7; 2020 IF: 1.457 |
| Call Number |
UA @ admin @ c:irua:174472 |
Serial |
8622 |
| Permanent link to this record |
| |
|
| |
| Author |
Eliaerts, J.; Meert, N.; Dardenne, P.; Van Durme, F.; Baeten, V.; Samyn, N.; De Wael, K. |
| Title |
Evaluation of a calibration transfer between a bench top and portable Mid-InfraRed spectrometer for cocaine classification and quantification |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Talanta |
Abbreviated Journal |
Talanta |
| Volume |
209 |
Issue |
|
Pages |
120481 |
| Keywords |
A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation) |
| Abstract |
A portable Fourier Transform Mid-InfraRed (FT-MIR) spectrometer using Attenuated Total Reflectance (ATR) sampling is used for daily routine screening of seized powders. Earlier, ATR-FT-MIR combined with Support Vector Machines (SVM) algorithms resulted in a significant improvement of the screening method to a reliable and straightforward classification and quantification tool for both cocaine and levamisole. However, can this tool be transferred to new (hand-held) devices, without loss of the extensive data set? The objective of this study was to perform a calibration transfer between a newly purchased bench top (BT) spectrometer and a portable (P) spectrometer with existing calibration models. Both instruments are from the same brand and have identical characteristics and acquisition parameters (FT instrument, resolution of 4 cm(-1) and wavenumber range 4000 to 500 cm(-1)). The original SVM classification model (n = 515) and SVM quantification model (n = 378) were considered for the transfer trial. Three calibration transfer strategies were assessed: 1) adjustment of slope and bias; 2) correction of spectra from the new instrument BT to P using Piecewise Direct Standardization (PDS) and 3) building a new mixed instrument model with spectra of both instruments. For each approach, additional cocaine powders were measured (n = 682) and the results were compared with GC-MS and GC-FID. The development of a mixed instrument model was the most successful in terms of performance. The future strategy of a mixed model allows applying the models, developed in the laboratory, to portable instruments that are used on-site, and vice versa. The approach offers opportunities to exchange data within a network of forensic laboratories using other FT-MIR spectrometers. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000509632900016 |
Publication Date |
2019-10-21 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0039-9140; 1873-3573 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
6.1 |
Times cited |
2 |
Open Access |
|
| Notes |
; ; |
Approved |
Most recent IF: 6.1; 2020 IF: 4.162 |
| Call Number |
UA @ admin @ c:irua:166475 |
Serial |
6511 |
| Permanent link to this record |
| |
|
| |
| Author |
Sciutto, G.; Legrand, S.; Catelli, E.; Prati, S.; Malegori, C.; Oliveri, P.; Janssens, K.; Mazzeo, R. |
| Title |
Macroscopic mid-FTIR mapping and clustering-based automated data-reduction : an advanced diagnostic tool for in situ investigations of artworks |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Talanta |
Abbreviated Journal |
Talanta |
| Volume |
209 |
Issue |
|
Pages |
120575-120577 |
| Keywords |
A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation) |
| Abstract |
The present study describes a multivariate strategy that can be used for automatic on-site processing of reflection mode macro FTIR mapping (MA-rFTIR) data obtained during investigation of artworks. The chemometric strategy is based on the integration of principal component analysis (PCA) with a clustering approach in the space subtended by the three lowest-order principal components and allows to automatically identify the regions of interest (ROIs) of the area scanned and to extract the average FTIR spectra related to each ROI. Thanks to the automatic data management, in-field HSI (hyperspectral imaging)-based analyses may be performed even by staff lacking specific advanced chemometric expertise, as it is sometimes the case for conservation scientists or conservators with a scientific background. MA-rFTIR was only recently introduced in the conservation field and, in this work the technique was employed to characterize the surface of metallic artefacts. The analytical protocol was employed as part of a rapid procedure to evaluate the conservation state and the performance of cleaning methods on bronze objects. Both activities are commonly part of restoration campaigns of bronzes and require an on-site analytical procedure for efficient and effective diagnosis. The performance of the method was first evaluated on aged standard samples (bronzes with a layer of green basic copper hydroxysulphate, treated with different organic coatings) and then scrutinized in situ on areas of the 16th century Neptune fountain statue (Piazza del Nettuno, Bologna, Italy) by Gianbologna. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000509632900088 |
Publication Date |
2019-11-19 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0039-9140; 1873-3573 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
6.1 |
Times cited |
|
Open Access |
|
| Notes |
; ; |
Approved |
Most recent IF: 6.1; 2020 IF: 4.162 |
| Call Number |
UA @ admin @ c:irua:166476 |
Serial |
6557 |
| Permanent link to this record |
| |
|
| |
| Author |
Lumbeeck, G.; Delvaux, A.; Idrissi, H.; Proost, J.; Schryvers, D. |
| Title |
Analysis of internal stress build-up during deposition of nanocrystalline Ni thin films using transmission electron microscopy |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Thin solid films : an international journal on the science and technology of thin and thick films |
Abbreviated Journal |
Thin Solid Films |
| Volume |
707 |
Issue |
|
Pages |
138076 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
Ni thin films sputter-deposited at room temperature with varying Ar pressures were investigated with automated crystal orientation mapping in a transmission electron microscope to uncover the mechanisms controlling the internal stress build-up recorded in-situ during deposition. Large grains were found to induce behaviour similar to a stress-free nucleation layer. The measurements of grain size in most of the Ni thin films are in agreement with the island coalescence model. Low internal stress was observed at low Ar pressure and was explained by the presence of large grains. Relaxation of high internal stress was also noticed at the highest Ar pressure, which was attributed to a decrease of Σ3 twin boundary density due to a low deposition rate. The results provide insightful information to better understand the relationship between structural boundaries and the evolution of internal stress upon deposition of thin films. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000539312200011 |
Publication Date |
2020-05-12 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
|
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
|
Times cited |
|
Open Access |
OpenAccess |
| Notes |
This work was supported by the Hercules Foundation [Grant No. AUHA13009], the Flemish Research Fund (FWO) [Grant No. G.0365.15N], and the Flemish Strategic Initiative for Materials (SIM) under the project InterPoCo. Thin film deposition has been realised as part of the WallonHY project, funded by the Public Service of Wallonia – Department of Energy and Sustainable Building. H. Idrissi is mandated by the Belgian National Fund for Scientific Research (FSR-FNRS). |
Approved |
Most recent IF: NA |
| Call Number |
EMAT @ emat @c:irua:169708 |
Serial |
6370 |
| Permanent link to this record |
| |
|
| |
| Author |
Sui, Y.; Vlaeminck, S.E. |
| Title |
Dunaliella microalgae for nutritional protein : an undervalued asset |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Trends in biotechnology : regular edition |
Abbreviated Journal |
|
| Volume |
38 |
Issue |
1 |
Pages |
10-12 |
| Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
β-carotene production using Dunaliella microalgae is established, yet their potential as a source of protein for food and feed applications appears to be overlooked. The rich protein content and nutritional tunability of Dunaliella make these algae intriguing sources of sustainable protein. Thus, it is of societal interest to exploit these promising proteinaceous Dunaliella traits. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000503376700004 |
Publication Date |
2019-08-23 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1879-3096; 0167-7799 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
17.3 |
Times cited |
2 |
Open Access |
|
| Notes |
; This work was supported by the China Scholarship Council (File No. 201507650015) and the MIP i-Clean-tech Flanders (Milieu-innovatieplatform; Environment Innovation Platform) project Microbial Nutrients on Demand (MicroNOD). Dr Michele Moretti from University of Antwerp is acknowledged for proofreading the manuscript. ; |
Approved |
Most recent IF: 17.3; 2020 IF: 11.126 |
| Call Number |
UA @ admin @ c:irua:164903 |
Serial |
6495 |
| Permanent link to this record |
| |
|
| |
| Author |
Yagmurcukardes, M. |
| Title |
Stable anisotropic single-layer of ReTe₂ : a first principles prediction |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Turkish Journal of Physics |
Abbreviated Journal |
|
| Volume |
44 |
Issue |
5 |
Pages |
450-457 |
| Keywords |
A1 Journal article; Condensed Matter Theory (CMT) |
| Abstract |
In order to investigate the structural, vibrational, electronic, and mechanical features of single-layer ReTe2 first-principles calculations are performed. Dynamical stability analyses reveal that single-layer ReTe2 crystallize in a distorted phase while its 1H and 1T phases are dynamically unstable. Raman spectrum calculations show that single-layer distorted phase of ReTe2 exhibits 18 Raman peaks similar to those of ReS2 and ReSe2. Electronically, single-layer ReTe2 is shown to be an indirect gap semiconductor with a suitable band gap for optoelectronic applications. In addition, it is found that the formation of Re-units in the crystal induces anisotropic mechanical parameters. The in-plane stiffness and Poisson ratio are shown to be significantly dependent on the lattice orientation. Our findings indicate that single-layer form of ReTe2 can only crystallize in a dynamically stable distorted phase formed by the Re-units. Single-layer of distorted ReTe2 can be a potential in-plane anisotropic material for various nanotechnology applications. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000585330600004 |
Publication Date |
2020-09-20 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1300-0101 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
|
Times cited |
|
Open Access |
|
| Notes |
; Computational resources were provided by the Scientific and Technological Research Council of Turkey (TUBITAK) Turkish Academic Network and Information Center (ULAKBIM), High Performance and Grid Computing Center (TR-Grid e-Infrastructure) and by Flemish Supercomputer Center (VSC). This work was supported by the Flemish Science Foundation (FWO-Vl) by a postdoctoral fellowship (M.Y.). ; |
Approved |
Most recent IF: NA |
| Call Number |
UA @ admin @ c:irua:174296 |
Serial |
6698 |
| Permanent link to this record |
| |
|
| |
| Author |
Velazco, A.; Nord, M.; Béché, A.; Verbeeck, J. |
| Title |
Evaluation of different rectangular scan strategies for STEM imaging |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Ultramicroscopy |
Abbreviated Journal |
Ultramicroscopy |
| Volume |
|
Issue |
|
Pages |
113021 |
| Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
| Abstract |
STEM imaging is typically performed by raster scanning a focused electron probe over a sample. Here we investigate and compare three different scan patterns, making use of a programmable scan engine that allows to arbitrarily set the sequence of probe positions that are consecutively visited on the sample. We compare the typical raster scan with a so-called ‘snake’ pattern where the scan direction is reversed after each row and a novel Hilbert scan pattern that changes scan direction rapidly and provides an homogeneous treatment of both scan directions. We experimentally evaluate the imaging performance on a single crystal test sample by varying dwell time and evaluating behaviour with respect to sample drift. We demonstrate the ability of the Hilbert scan pattern to more faithfully represent the high frequency content of the image in the presence of sample drift. It is also shown that Hilbert scanning provides reduced bias when measuring lattice parameters from the obtained scanned images while maintaining similar precision in both scan directions which is especially important when e.g. performing strain analysis. Compared to raster scanning with flyback correction, both snake and Hilbert scanning benefit from dose reduction as only small probe movement steps occur. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000544042800007 |
Publication Date |
2020-05-21 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0304-3991 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
2.2 |
Times cited |
13 |
Open Access |
OpenAccess |
| Notes |
A.V., A.B. and J.V. acknowledge funding through FWO project G093417N ('Compressed sensing enabling low dose imaging in transmission electron microscopy') from the Flanders Research Fund. M.N. received support for this work from the European Union's Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No 838001. J.V acknowledges funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 823717 – ESTEEM3. |
Approved |
Most recent IF: 2.2; 2020 IF: 2.843 |
| Call Number |
EMAT @ emat @c:irua:169225 |
Serial |
6369 |
| Permanent link to this record |
