|
Records |
|
Author |
Goris, B.; Meledina, M.; Turner, S.; Zhong, Z.; Batenburg, K.J.; Bals, S. |
|
Title |
Three dimensional mapping of Fe dopants in ceria nanocrystals using direct spectroscopic electron tomography |
Type |
A1 Journal article |
|
Year |
2016 |
Publication |
Ultramicroscopy |
Abbreviated Journal |
Ultramicroscopy |
|
Volume |
171 |
Issue |
171 |
Pages |
55-62 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Electron tomography is a powerful technique for the 3D characterization of the morphology of nanostructures. Nevertheless, resolving the chemical composition of complex nanostructures in 3D remains challenging and the number of studies in which electron energy loss spectroscopy (EELS) is combined with tomography is limited. During the last decade, dedicated reconstruction algorithms have been developed for HAADF-STEM tomography using prior knowledge about the investigated sample. Here, we will use the prior knowledge that the experimental spectrum of each reconstructed voxel is a linear combination of a well-known set of references spectra in a so-called direct spectroscopic tomography technique. Based on a simulation experiment, it is shown that this technique provides superior results in comparison to conventional reconstruction methods for spectroscopic data, especially for spectrum images containing a relatively low signal to noise ratio. Next, this technique is used to investigate the spatial distribution of Fe dopants in Fe:Ceria nanoparticles in 3D. It is shown that the presence of the Fe2+ dopants is correlated with a reduction of the Ce atoms from Ce4+ towards Ce3+. In addition, it is demonstrated that most of the Fe dopants are located near the voids inside the nanoparticle. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000389106200007 |
Publication Date |
2016-09-06 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0304-3991 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
2.843 |
Times cited |
13 |
Open Access |
OpenAccess |
|
Notes |
The work was supported by the Research Foundation Flanders (FWO Vlaanderen) by project funding (G038116N, 3G004613) and by a post-doctoral research grants to B.G. S.B. acknowledges funding from the European Research Council (Starting Grant no. COLOURATOMS 335078). K.J.B. acknowledges funding from The Netherlands Organization for Scientific Research (NWO) (program 639.072.005.). We would like to thank Dr. Hilde Poelman, Dr. Vladimir Galvita and Prof. Dr. Guy B. Marin for the synthesis of the investigated sample.; ECAS_Sara; (ROMEO:green; preprint:; postprint:can ; pdfversion:cannot); |
Approved |
Most recent IF: 2.843 |
|
Call Number |
c:irua:135185 c:irua:135185 |
Serial |
4123 |
Permanent link to this record |
|
|
|
|
Author |
Cui, J.; Faria, M.; Bjornmalm, M.; Ju, Y.; Suma, T.; Gunawan, S.T.; Richardson, J.J.; Heidar, H.; Bals, S.; Crampin, E.J.; Caruso, F. |
|
Title |
A framework to account for sedimentation and diffusion in particle-cell interactions |
Type |
A1 Journal article |
|
Year |
2016 |
Publication |
Langmuir: the ACS journal of surfaces and colloids |
Abbreviated Journal |
Langmuir |
|
Volume |
32 |
Issue |
32 |
Pages |
12394-12402 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
In vitro experiments provide a solid basis for understanding the interactions between particles and biological systems. An important confounding variable for these studies is the difference between the amount of particles administered and that which reaches the surface of cells. Here, we engineer a hydrogel-based nanoparticle system and combine in situ characterization techniques, 3D-printed cell cultures, and computational modeling to evaluate and study particle cell interactions of advanced particle systems. The framework presented demonstrates how sedimentation and diffusion can explain differences in particle cell association, and provides a means to account for these effects. Finally, using in silico modeling, we predict the proportion of particles that reaches the cell surface using common experimental conditions for a wide range of inorganic and organic micro- and nanoparticles. This work can assist in the understanding and control of sedimentation and diffusion when investigating cellular interactions of engineered particles. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Washington, D.C. |
Editor |
|
|
Language |
|
Wos |
000389117600017 |
Publication Date |
2016-07-06 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0743-7463 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
3.833 |
Times cited |
40 |
Open Access |
Not_Open_Access |
|
Notes |
; This work was supported by the Australian Research Council (ARC) under the Australian Laureate Fellowship scheme (F.C., FL120100030), the Australian Government through an Australian Postgraduate Award (M.B.), and the ARC Centre of Excellence in Convergent Bio-Nano Science and Technology (Project Number CE140100036). This work was performed in part at the Materials Characterization and Fabrication Platform (MCFP) at the University of Melbourne and the Victorian Node of the Australian National Fabrication Facility (ANFF). ; |
Approved |
Most recent IF: 3.833 |
|
Call Number |
UA @ lucian @ c:irua:139210 |
Serial |
4438 |
Permanent link to this record |
|
|
|
|
Author |
Rodal-Cedeira, S.; Montes-García, V.; Polavarapu, L.; Solís, D.M.; Heidari, H.; La Porta, A.; Angiola, M.; Martucci, A.; Taboada, J.M.; Obelleiro, F.; Bals, S.; Pérez-Juste, J.; Pastoriza-Santos, I. |
|
Title |
Plasmonic Au@Pd Nanorods with Boosted Refractive Index Susceptibility and SERS Efficiency: A Multifunctional Platform for Hydrogen Sensing and Monitoring of Catalytic Reactions |
Type |
A1 Journal article |
|
Year |
2016 |
Publication |
Chemistry of materials |
Abbreviated Journal |
Chem Mater |
|
Volume |
28 |
Issue |
28 |
Pages |
9169-9180 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Palladium nanoparticles (NPs) have received tremendous attention over the years due to their high catalytic activity for various chemical reactions. However, unlike other noble metal nanoparticles such as Au and Ag NPs, they exhibit poor plasmonic properties with broad extinction spectra and less scattering efficiency, and thus limiting their applications in the field of plasmonics. Therefore, it has been challenging to integrate tunable and strong plasmonic properties into catalytic Pd nanoparticles. Here we show that plasmonic Au@Pd nanorods (NRs) with relatively narrow and remarkably tunable optical responses in the NIR region can be obtained by directional growth of Pd on penta-twinned Au NR seeds. We found the presence of bromide ions facilitates the stabilization of facets for the directional growth of Pd shell to obtain Au@Pd nanorods (NR) with controlled length scales. Interestingly, it turns out the Au NR supported Pd NRs exhibit much narrow extinction compared to pure Pd NRs, which makes them suitable for plasmonic sensing applications. Moreover, these nanostructures display, to the best of our knowledge, one of the highest ensemble refractive index sensitivity values reported to date (1067 nm per refractive index unit, RIU). Additionally, we showed the application of such plasmonic Au@Pd NRs for localized surface plasmon resonance (LSPR)-based sensing of hydrogen both in solution as well as on substrate. Finally, we demonstrate the integration of excellent plasmonic properties in catalytic palladium enables the in situ monitoring of a reaction progress by surface-enhanced Raman scattering. We postulate the proposed approach to boost the plasmonic properties of Pd nanoparticles will ignite the design of complex shaped plasmonic Pd NPs to be used in various plasmonic applications such as sensing and in situ monitoring of various chemical reactions. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000391080900036 |
Publication Date |
2016-12-27 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0897-4756 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
9.466 |
Times cited |
80 |
Open Access |
OpenAccess |
|
Notes |
Funding from Spanish Ministerio de Economía y Competitividad (Grants MAT2013-45168-R and MAT2016-77809-R) is gratefully acknowledge. A.L.P. and S.B. acknowledge support by the European Research Council through an ERC Starting Grant (#335078-COLOURATOMS). L. P. acknowledges the financial support from by the Alexander von Humboldt-Stiftung. V. M.-G. acknowledges the financial support from FPU scholarship from the Spanish MINECO. (ROMEO:white; preprint:; postprint:restricted 12 months embargo; pdfversion:cannot); ECAS_Sara |
Approved |
Most recent IF: 9.466 |
|
Call Number |
EMAT @ emat @ c:irua:139513 |
Serial |
4344 |
Permanent link to this record |
|
|
|
|
Author |
Grzelczak, M.; Sanchez-Iglesias, A.; Heidari, H.; Bals, S.; Pastoriza-Santos, I.; Perez-Juste, J.; Liz-Marzan, L.M. |
|
Title |
Silver Ions Direct Twin-Plane Formation during the Overgrowth of Single-Crystal Gold Nanoparticles |
Type |
A1 Journal article |
|
Year |
2016 |
Publication |
ACS Omega |
Abbreviated Journal |
|
|
Volume |
1 |
Issue |
1 |
Pages |
177-181 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
It is commonly agreed that the crystalline structure of seeds dictates the crystallinity of final nanoparticles in a seeded-growth process. Although the formation of monocrystalline particles does require the use of single-crystal seeds, twin planes may stem from either single-or polycrystalline seeds. However, experimental control over twin-plane formation remains difficult to achieve synthetically. Here, we show that a careful interplay between kinetics and selective surface passivation offers a unique handle over the emergence of twin planes (in decahedra and triangles) during the growth over single-crystalline gold nanoparticles of quasi-spherical shape. Twinning can be suppressed under conditions of slow kinetics in the presence of silver ions, yielding single-crystalline particles with high-index facets. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000391203300002 |
Publication Date |
2016-08-03 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2470-1343;2470-1343; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
|
Times cited |
18 |
Open Access |
OpenAccess |
|
Notes |
; This work was supported by the Spanish Ministerio de Economia y Competitividad MINECO (grants: MAT2013-46101-R, MAT2013-49375-EXP, MAT2013-45168-R). Financial support is acknowledged by the European Research Council (ERC Advanced Grant # 267867, PLASMAQUO; ERC Starting Grant #335078-COLOURATOM). ; ecas_Sara |
Approved |
Most recent IF: NA |
|
Call Number |
UA @ lucian @ c:irua:140398 |
Serial |
4446 |
Permanent link to this record |
|
|
|
|
Author |
Sánchez-Iglesias, A.; Winckelmans, N.; Altantzis, T.; Bals, S.; Grzelczak, M.; Liz-Marzán, L.M. |
|
Title |
High-Yield Seeded Growth of Monodisperse Pentatwinned Gold Nanoparticles through Thermally Induced Seed Twinning |
Type |
A1 Journal article |
|
Year |
2016 |
Publication |
Journal of the American Chemical Society |
Abbreviated Journal |
J Am Chem Soc |
|
Volume |
139 |
Issue |
139 |
Pages |
107-110 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
We show here that thermal treatment of small seeds results in extensive twinning and a subsequent drastic yield improvement (>85%) in the formation of pentatwinned nanoparticles, with pre-selected morphology (nanorods, bipyramids and decahedra) and aspect ratio. The “quality” of the seeds thus defines the yield of the obtained nanoparticles, which in the case of nanorods avoids the need for additives such as Ag+ ions. This modified seeded growth method also improves reproducibility, as the seeds can be stored for extended periods of time without compromising the quality of the final nanoparticles. Additionally, minor modification of the seeds with Pd allows their localization within the final particles, which opens new avenues toward mechanistic studies. All together, these results represent a paradigm shift in anisotropic gold nanoparticle synthesis. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000392036900025 |
Publication Date |
2016-12-29 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0002-7863 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
13.858 |
Times cited |
267 |
Open Access |
OpenAccess |
|
Notes |
Financial support is acknowledged from the European Research Council through ERC Advanced Grant Plasmaquo and the ERC Starting Grant COLOURATOM. T.A. acknowledges financial support from the Research Foundation Flanders (FWO, Belgium) through a postdoctoral grant. (ROMEO:white; preprint:; postprint:restricted 12 months embargo; pdfversion:cannot); ECAS_Sara |
Approved |
Most recent IF: 13.858 |
|
Call Number |
EMAT @ emat @ c:irua:139018UA @ admin @ c:irua:139018 |
Serial |
4339 |
Permanent link to this record |
|
|
|
|
Author |
Van Tendeloo, L.; Wangermez, W.; Vandekerkhove, A.; Willhammar, T.; Bals, S.; Maes, A.; Martens, J.A.; Kirschhock, C.E.A.; Breynaert, E. |
|
Title |
Postsynthetic high-alumina zeolite crystal engineering in organic free hyper-alkaline media |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Chemistry of materials |
Abbreviated Journal |
Chem Mater |
|
Volume |
29 |
Issue |
29 |
Pages |
629-638 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Postsynthetic modification of high -alumina zeolites in hyper alkaline media can be tailored toward alteration of framework topology, crystal size and morphology, or desired Si/A1 ratio. FAU, EMT, MAZ, KFI, HEU, and LTA starting materials were treated with 1.2 M MOH (M = Na, K, RE, or Cs), leading to systematic ordered porosity or fully transformed frameworks with new topology and adjustable Si/Al ratio. In addition to the versatility of this tool for zeolite crystal engineering, these alterations improve understanding of the crystal chemistry. Such knowledge can guide further development in zeolite crystal engineering. Postsynthetic alteration also provides insight on the long-term stability of aluminosilicate zeolites that are used as a sorption sink in concrete -based waste disposal facilities in harsh alkaline conditions. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
American Chemical Society |
Place of Publication |
Washington, D.C |
Editor |
|
|
Language |
|
Wos |
000392891700021 |
Publication Date |
2016-12-20 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0897-4756 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
9.466 |
Times cited |
16 |
Open Access |
OpenAccess |
|
Notes |
; This work was supported by long-term structural funding by the Flemish Government (Methusalem grant of Prof. J. Martens) and by ONDRAF/NIRAS, the Belgian Agency for Radioactive Waste and Fissile Materials, as part of the program on surface disposal of Belgian Category A waste. The Belgian government is acknowledged for financing the interuniversity poles of attraction (IAP-PAI). S.B. acknowledges financial support from European Research Council (ERC Advanced Grant No. 24691-COUNTATOMS, ERC Starting Grant No. 335078-COLOURATOMS). ; Ecas_Sara |
Approved |
Most recent IF: 9.466 |
|
Call Number |
UA @ lucian @ c:irua:152674UA @ admin @ c:irua:152674 |
Serial |
5145 |
Permanent link to this record |
|
|
|
|
Author |
Suffian, I.F.B.M.; Wang, J.T.-W.; Hodgins, N.O.; Klippstein, R.; Garcia-Maya, M.; Brown, P.; Nishimura, Y.; Heidari, H.; Bals, S.; Sosabowski, J.K.; Ogino, C.; Kondo, A.; Al-Jamal, K.T. |
|
Title |
Engineering hepatitis B virus core particles for targeting HER2 receptors in vitro and in vivo |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Biomaterials |
Abbreviated Journal |
Biomaterials |
|
Volume |
120 |
Issue |
120 |
Pages |
126-138 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Hepatitis B Virus core (HBc) particles have been studied for their potential as drug delivery vehicles for cancer therapy. HBc particles are hollow nano-particles of 30-34 nm diameter and 7 nm thick envelopes, consisting of 180-240 units of 21 kDa core monomers. They have the capacity to assemble/dis-assemble in a controlled manner allowing encapsulation of various drugs and other biomolecules. Moreover, other functional motifs, i.e. receptors, receptor binding sequences, peptides and proteins can be expressed. This study focuses on the development of genetically modified HBc particles to specifically recognise and target human epidermal growth factor receptor-2 (HER2)-expressing cancer cells, in vitro and in vivo, for future cancer therapy. The non-specific binding capacity of wild type HBc particles was reduced by genetic deletion of the sequence encoding arginine-rich domains. A specific HER2-targeting was achieved by expressing the ZHER2 affibodies on the HBc particles surface. In vitro studies showed specific uptake of ZHER2-AHBc particles in HER2 expressing cancer cells. In vivo studies confirmed positive uptake of ZHER2-ABBc particles in HER2-expressing tumours, compared to non-targeted AHBc particles in intraperitoneal tumour-bearing mice models. The present results highlight the potential of these nanocarriers in targeting HER2-positive metastatic abdominal cancer following intra-peritoneal administration. (C) 2016 The Authors. Published by Elsevier Ltd. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Guildford |
Editor |
|
|
Language |
|
Wos |
000394398900012 |
Publication Date |
2016-12-14 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0142-9612 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
8.402 |
Times cited |
20 |
Open Access |
OpenAccess |
|
Notes |
; The authors would like to thank Dr. Rafael T. M. de Rosales (King's College London) for useful discussion on the radiolabelling technique and Mr William Luckhurst (King's College London) on the technical help of AFM measurements. IFBMS would like to thank Public Service Department, Government of Malaysia for the Excellence Student Programme studentship. We acknowledge funding from Biotechnology and Biological Sciences Research Council (BBSRC; (BB/J008656/1)) and the EU FP7-ITN Marie-Curie Network programme RADDEL (290023). NH is a recipient of Graduate School King's Health Partner's scholarship. RIC is a Marie Curie Fellow. S.B. acknowledges funding from the European Research Council under the 7th Framework Program (FP7), ERC Starting Grant No. 335078 COLOURATOMS, and the Integrated Infrastructure Initiative No. 262348 European Soft Matter Infrastructure, ESMI. The authors declare that they have no competing interests. ; ecas_Sara |
Approved |
Most recent IF: 8.402 |
|
Call Number |
UA @ lucian @ c:irua:141984UA @ admin @ c:irua:141984 |
Serial |
4654 |
Permanent link to this record |
|
|
|
|
Author |
Ben Dkhil, S.; Pfannmöller, M.; Ata, I.; Duche, D.; Gaceur, M.; Koganezawa, T.; Yoshimoto, N.; Simon, J.-J.; Escoubas, L.; Videlot-Ackermann, C.; Margeat, O.; Bals, S.; Bauerle, P.; Ackermann, J. |
|
Title |
Time evolution studies of dithieno[3,2-b:2 ',3 '-d] pyrrole-based A-D-A oligothiophene bulk heterojunctions during solvent vapor annealing towards optimization of photocurrent generation |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Journal of materials chemistry A : materials for energy and sustainability |
Abbreviated Journal |
J Mater Chem A |
|
Volume |
5 |
Issue |
5 |
Pages |
1005-1013 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
Solvent vapor annealing (SVA) is one of the main techniques to improve the morphology of bulk heterojunction solar cells using oligomeric donors. In this report, we study time evolution of nanoscale morphological changes in bulk heterojunctions based on a well-studied dithienopyrrole-based A-D-A oligothiophene (dithieno[3,2-b: 2',3'-d] pyrrole named here 1) blended with [6,6]-phenyl-C-71-butyric acid methyl ester (PC71BM) to increase photocurrent density by combining scanning transmission electron microscopy and low-energy-loss spectroscopy. Our results show that SVA transforms the morphology of 1 : PC71BM blends by a three-stage mechanism: highly intermixed phases evolve into nanostructured bilayers that correspond to an optimal blend morphology. Additional SVA leads to completely phaseseparated micrometer-sized domains. Optical spacers were used to increase light absorption inside optimized 1 : PC71BM blends leading to solar cells of 7.74% efficiency but a moderate photocurrent density of 12.3 mA cm (-2). Quantum efficiency analyses reveal that photocurrent density is mainly limited by losses inside the donor phase. Indeed, optimized 1 : PC71BM blends consist of large donor-enriched domains not optimal for exciton to photocurrent conversion. Shorter SVA times lead to smaller domains; however they are embedded in large mixed phases suggesting that introduction of stronger molecular packing may help us to better balance phase separation and domain size enabling more efficient bulk heterojunction solar cells. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Cambridge |
Editor |
|
|
Language |
|
Wos |
000394430800018 |
Publication Date |
2016-11-30 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2050-7488; 2050-7496 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
8.867 |
Times cited |
19 |
Open Access |
Not_Open_Access |
|
Notes |
; We acknowledge financial support by the French Fond Unique Interministeriel (FUI) under the project “SFUMATO” (Grant number: F1110019V/201308815) as well as by the European Commission under the Project “SUNFLOWER” (FP7-ICT-2011-7, Grant number: 287594). The synchrotron radiation experiments were performed at BL19B2 in SPring-8 with the approval of Japan Synchrotron Radiation Research Institute (JASRI) (Proposal No. 2016A1568). We further acknowledge financial support via ERC Starting Grant Colouratoms (335078). ; |
Approved |
Most recent IF: 8.867 |
|
Call Number |
UA @ lucian @ c:irua:142602UA @ admin @ c:irua:142602 |
Serial |
4695 |
Permanent link to this record |
|
|
|
|
Author |
Kurttepeli, M.; Deng, S.; Mattelaer, F.; Cott, D.J.; Vereecken, P.; Dendooven, J.; Detavernier, C.; Bals, S. |
|
Title |
Heterogeneous TiO2/V2O5/Carbon Nanotube Electrodes for Lithium-Ion Batteries |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
ACS applied materials and interfaces |
Abbreviated Journal |
Acs Appl Mater Inter |
|
Volume |
9 |
Issue |
9 |
Pages |
8055-8064 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
Vanadium pentoxide (V2O5) is proposed and investigated as a cathode material for lithium-ion (Li-ion) batteries. However, the dissolution of V2O5 during the charge/discharge remains as an issue at the V2O5–electrolyte interface. In this work, we present a heterogeneous nanostructure with carbon nanotubes supported V2O5/titanium dioxide (TiO2) multilayers as electrodes for thin-film Li-ion batteries. Atomic layer deposition of V2O5 on carbon nanotubes provides enhanced Li storage capacity and high rate performance. An additional TiO2 layer leads to increased morphological stability and in return higher electrochemical cycling performance of V2O5/carbon nanotubes. The physical and chemical properties of TiO2/V2O5/carbon nanotubes are characterized by cyclic voltammetry and charge/discharge measurements as well as electron microscopy. The detailed mechanism of the protective TiO2 layer to improve the electrochemical cycling stability of the V2O5 is unveiled. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000396186000021 |
Publication Date |
2017-03-08 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
1944-8244 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
7.504 |
Times cited |
28 |
Open Access |
OpenAccess |
|
Notes |
European Research Council, 239865 335078 ; Fonds Wetenschappelijk Onderzoek; Agentschap voor Innovatie door Wetenschap en Technologie, 18142 ; Bijzonder Onderzoeksfonds, GOA – 01G01513 ; This research was funded by the Flemish research foundation FWO-Vlaanderen, by the European Research Council (Starting Grant No. 239865 and No. 335078), by IWT-Flanders (SBO project IWT 18142 “SoS-Lion”) and by the Special Research Fund BOF of Ghent University (GOA – 01G01513); colouratoms (ROMEO:white; preprint:; postprint:restricted 12 months embargo; pdfversion:cannot); ECAS_Sara |
Approved |
Most recent IF: 7.504 |
|
Call Number |
EMAT @ emat @ c:irua:142446UA @ admin @ c:irua:142446 |
Serial |
4572 |
Permanent link to this record |
|
|
|
|
Author |
Ben Dkhil, S.; Pfannmöller, M.; Saba, M.I.; Gaceur, M.; Heidari, H.; Videlot-Ackermann, C.; Margeat, O.; Guerrero, A.; Bisquert, J.; Garcia-Belmonte, G.; Mattoni, A.; Bals, S.; Ackermann, J. |
|
Title |
Toward high-temperature stability of PTB7-based bulk heterojunction solar cells : impact of fullerene size and solvent additive |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Laser physics review |
Abbreviated Journal |
Adv Energy Mater |
|
Volume |
7 |
Issue |
7 |
Pages |
1601486 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
The use of fullerene as acceptor limits the thermal stability of organic solar cells at high temperatures as their diffusion inside the donor leads to phase separation via Ostwald ripening. Here it is reported that fullerene diffusion is fully suppressed at temperatures up to 140 degrees C in bulk heterojunctions based on the benzodithiophene-based polymer (the poly[[4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b: 4,5-b']dithiophene-2,6-diyl][3-fluoro-2-[(2-ethylhexyl) carbonyl]thieno[3,4-b]thiophenediyl]], (PTB7) in combination with the fullerene derivative [6,6]-phenyl-C71-butyric acid methyl ester (PC70BM). The blend stability is found independently of the presence of diiodooctane (DIO) used to optimize nanostructuration and in contrast to PTB7 blends using the smaller fullerene derivative PC70BM. The unprecedented thermal stability of PTB7: PC70BM layers is addressed to local minima in the mixing enthalpy of the blend forming stable phases that inhibit fullerene diffusion. Importantly, although the nanoscale morphology of DIO processed blends is thermally stable, corresponding devices show strong performance losses under thermal stress. Only by the use of a high temperature annealing step removing residual DIO from the device, remarkably stable high efficiency solar cells with performance losses less than 10% after a continuous annealing at 140 degrees C over 3 days are obtained. These results pave the way toward high temperature stable polymer solar cells using fullerene acceptors. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Place of publication unknown |
Editor |
|
|
Language |
|
Wos |
000396328500009 |
Publication Date |
2016-11-07 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
1614-6832; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
16.721 |
Times cited |
27 |
Open Access |
Not_Open_Access |
|
Notes |
; The authors acknowledge financial support by the French Fond Unique Interministeriel (FUI) under the project “SFUMATO” (grant number: F1110019V/ 201308815) as well as by the European Commission under the Project “SUNFLOWER” (FP7-ICT-2011-7, grant number: 287594). Generalitat Valenciana (ISIC/2012/008 Institute of Nanotechnologies for Clean Energies) is also acknowledged for providing financial support. The authors further acknowledge financial support via ERC Starting Grant Colouratoms (335078). ; |
Approved |
Most recent IF: 16.721 |
|
Call Number |
UA @ lucian @ c:irua:141991UA @ admin @ c:irua:141991 |
Serial |
4697 |
Permanent link to this record |
|
|
|
|
Author |
Barhoum, A.; Van Assche, G.; Rahier, H.; Fleisch, M.; Bals, S.; Delplancked, M.-P.; Leroux, F.; Bahnemann, D. |
|
Title |
Sol-gel hot injection synthesis of ZnO nanoparticles into a porous silica matrix and reaction mechanism |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Materials & design |
Abbreviated Journal |
Mater Design |
|
Volume |
119 |
Issue |
119 |
Pages |
270-276 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Despite the enormous interest in the properties and applications of porous silica matrix, only a few attempts have been reported to deposit metal and metal oxide nanoparticles (NPs) inside the porous silica matrix. We report a simple approach (i.e. sol-gel hot injection) for insitu synthesis of ZnO NPs inside a porous silica matrix. Control of the Zn:Si molar ratio, reaction temperature, pH value, and annealing temperature permits formation of ZnO NPs (<= 10 nm) inside a porous silica particles, without additives or organic solvents. Results revealed that a solid state reaction inside the ZnO/SiO2 nanocomposites occurs with increasing the annealing temperature. The reaction of ZnO NPs with SiO2 matrix was insignificant up to approximately 500 degrees C. However, ZnO NPs react strongly with the silica matrix when the nanocomposites are annealed at temperatures above 700 degrees C. Extensive annealing of the ZnO/SiO2 nanocomposite at 900 degrees C yields 3D structures made of 500 nm rod-like, 5-7 pm tube-like and 35 pm needle-like Zn2SiO4 crystals. A possible mechanism for forming ZnO NPs inside porous silica matrix and phase transformation of the ZnO/SiO2 nanocomposites into 3D architectures of Zn2SiO4 are carefully discussed. (C) 2017 Elsevier Ltd. All rights reserved. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000397360000030 |
Publication Date |
2017-01-23 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0264-1275 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
4.364 |
Times cited |
43 |
Open Access |
Not_Open_Access |
|
Notes |
; A.B. would like to thank FWO – Research Foundation Flanders (grant no. V450315N) and the Strategic Initiative Materials in Flanders (SBO-project no. 130529 – INSITU) for financial support. TEM and TEM-EDX analyses were performed by Dr. F. Leroux (EMAT, Universiteit Antwerpen). XRD and DSC measurements were performed by T. Segato (4MAT, Universite Libre de Bruxelles). Notes: the authors declare no competing for financial interest. ; |
Approved |
Most recent IF: 4.364 |
|
Call Number |
UA @ lucian @ c:irua:142394UA @ admin @ c:irua:142394 |
Serial |
4689 |
Permanent link to this record |
|
|
|
|
Author |
van der Stam, W.; Geuchies, J.J.; Altantzis, T.; van den Bos, K.H.W.; Meeldijk, J.D.; Van Aert, S.; Bals, S.; Vanmaekelbergh, D.; de Mello Donega, C. |
|
Title |
Highly Emissive Divalent-Ion-Doped Colloidal CsPb1–xMxBr3Perovskite Nanocrystals through Cation Exchange |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Journal of the American Chemical Society |
Abbreviated Journal |
J Am Chem Soc |
|
Volume |
139 |
Issue |
139 |
Pages |
4087-4097 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Colloidal CsPbX3 (X = Br, Cl, and I) perovskite nanocrystals (NCs) have emerged as promising phosphors and solar cell materials due to their remarkable optoelectronic properties. These properties can be tailored by not only controlling the size and shape of the NCs but also postsynthetic composition tuning through topotactic
anion exchange. In contrast, property control by cation exchange is still underdeveloped for colloidal CsPbX3 NCs. Here, we present a method that allows partial cation exchange in colloidal CsPbBr3 NCs, whereby Pb2+ is exchanged for several isovalent cations, resulting in doped CsPb1−xMxBr3 NCs (M= Sn2+, Cd2+, and Zn2+; 0 < x ≤ 0.1), with preservation of the original NC shape. The size of the parent NCs is also preserved in the product NCs, apart from a small (few
%) contraction of the unit cells upon incorporation of the guest cations. The partial Pb2+ for M2+ exchange leads to a blue-shift of the optical spectra, while maintaining the high photoluminescence quantum yields (>50%), sharp absorption features, and narrow emission of the parent CsPbBr3 NCs. The blue-shift in the optical spectra is attributed to the lattice contraction that accompanies the Pb2+ for M2+ cation exchange and is observed to scale linearly with the lattice contraction. This work opens up new possibilities to engineer the properties of halide perovskite NCs, which to date are demonstrated to be the only known
system where cation and anion exchange reactions can be sequentially combined while preserving the original NC shape, resulting in compositionally diverse perovskite NCs. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000397477700027 |
Publication Date |
2017-03-10 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0002-7863 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
13.858 |
Times cited |
535 |
Open Access |
OpenAccess |
|
Notes |
W.v.d.S. and C.d.M.D. acknowledge financial support from the division of Chemical Sciences (CW) of The Netherlands Organization for Scientific Research (NWO) under grant number ECHO.712.012.001. J.J.G. and D.V. acknowledge financial support from the Debye Graduate program. S.B. acknowledges financial support from the European Research Council (ERC Starting Grant # 335078-COLOURATOMS). K.H.W.v.d.B., S.B., S.V.A. and T.A. acknowledge financial support from the Research Foundation Flanders (FWO, Belgium) through project fundings (G.0374.13N, G.0368.15N, G.0369.15N), a Ph.D. grant to K.H.W.v.d.B, and a postdoctoral research grant to T.A. (ROMEO:white; preprint:; postprint:restricted 12 months embargo; pdfversion:cannot); ECAS_Sara |
Approved |
Most recent IF: 13.858 |
|
Call Number |
EMAT @ emat @ c:irua:141754UA @ admin @ c:irua:141754 |
Serial |
4482 |
Permanent link to this record |
|
|
|
|
Author |
Willhammar, T.; Sentosun, K.; Mourdikoudis, S.; Goris, B.; Kurttepeli, M.; Bercx, M.; Lamoen, D.; Partoens, B.; Pastoriza-Santos, I.; Pérez-Juste, J.; Liz-Marzán, L.M.; Bals, S.; Van Tendeloo, G. |
|
Title |
Structure and vacancy distribution in copper telluride nanoparticles influence plasmonic activity in the near-infrared |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Nature communications |
Abbreviated Journal |
Nat Commun |
|
Volume |
8 |
Issue |
8 |
Pages |
14925 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Condensed Matter Theory (CMT) |
|
Abstract |
Copper chalcogenides find applications in different domains including photonics, photothermal therapy and photovoltaics. CuTe nanocrystals have been proposed as an alternative to noble metal particles for plasmonics. Although it is known that deviations from stoichiometry are a prerequisite for plasmonic activity in the near-infrared, an accurate description of the material and its (optical) properties is hindered by an insufficient understanding of the atomic structure and the influence of defects, especially for materials in their nanocrystalline form. We demonstrate that the structure of Cu1.5±xTe nanocrystals canbe determined using electron diffraction tomography. Real-space high-resolution electron tomography directly reveals the three-dimensional distribution of vacancies in the structure. Through first-principles density functional theory, we furthermore demonstrate that the influence of these vacancies on the optical properties of the nanocrystals is determined. Since our methodology is applicable to a variety of crystalline nanostructured materials, it is expected to provide unique insights concerning structure–property correlations. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000397799700001 |
Publication Date |
2017-03-30 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2041-1723 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
12.124 |
Times cited |
37 |
Open Access |
OpenAccess |
|
Notes |
The work was financially supported by the European Research Council through an ERC Starting Grant (#335078-COLOURATOMS). T.W. acknowledges the Swedish Research Council for an international postdoc grant. We acknowledge financial support of FWO-Vlaanderen through project G.0216.14N, G.0369.15N and a postdoctoral research grant to B.G. The computational resources and services used in this work were provided by the VSC (Flemish Supercomputer Center) and the HPC infrastructure of the University of Antwerp (CalcUA), both funded by the FWO-Vlaanderen and the Flemish Government–Department EWI. The work was further supported by the Spanish MINECO (MAT2013-45168-R). S.M. thanks the Action ooSupporting Postdoctoral Researchers44 of the Operational Program ‘Education and Lifelong Learning’ (Action’s Beneficiary: General Secretariat for Research and Technology of Greece), which was co-financed by the European Social Fund (ESF) and the Greek State. (ROMEO:green; preprint:; postprint:can ; pdfversion:can); ECAS_Sara |
Approved |
Most recent IF: 12.124 |
|
Call Number |
EMAT @ emat @ c:irua:142203UA @ admin @ c:irua:142203 |
Serial |
4538 |
Permanent link to this record |
|
|
|
|
Author |
Benetti, G.; Cavaliere, E.; Canteri, A.; Landini, G.; Rossolini, G.M.; Pallecchi, L.; Chiodi, M.; Van Bael, M.J.; Winckelmans, N.; Bals, S.; Gavioli, L. |
|
Title |
Direct synthesis of antimicrobial coatings based on tailored bi-elemental nanoparticles |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
APL materials |
Abbreviated Journal |
Apl Mater |
|
Volume |
5 |
Issue |
5 |
Pages |
036105 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
Ultrathin coatings based on bi-elemental nanoparticles (NPs) are very promising to limit the surface-related spread of bacterial pathogens, particularly in nosocomial environments. However, tailoring the synthesis, composition, adhesion to substrate, and antimicrobial spectrum of the coating is an open challenge. Herein, we report on a radically new nanostructured coating, obtained by a one-step gas-phase deposition technique, and composed of bi-elemental Janus type Ag/Ti NPs. The NPs are characterized by a cluster-in-cluster mixing phase with metallic Ag nano-crystals embedded in amorphous TiO2 and present a promising antimicrobial activity including also multidrug resistant strains. We demonstrate the flexibility of the method to tune the embedded Ag nano-crystals dimension, the total relative composition of the coating, and the substrate type, opening the possibility of tailoring the dimension, composition, antimicrobial spectrum, and other physical/chemical properties of such multi-elemental systems. This work is expected to significantly spread the range of applications of NPs coatings, not only as an effective tool in the prevention of healthcare-associated infections but also in other technologically relevant fields like sensors or nano-/micro joining. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000398951000014 |
Publication Date |
2017-03-20 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2166-532X |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
4.335 |
Times cited |
21 |
Open Access |
OpenAccess |
|
Notes |
We thank Urs Gfeller for the XRF measurements, Francesco Banfi for valuable discussions on the manuscript and Giulio Viano for his valuable support in the microbiological analysis. The authors acknowledge the financial support of Universita Cattolica del Sacro Cuore through D.2.2 and D.3.1 grants and from the European Union through the 7th Framework Program (FP7) under a contract for an Integrated Infrastructure Initiative (Reference No. 312483 ESTEEM2). REFERENCES |
Approved |
Most recent IF: 4.335 |
|
Call Number |
EMAT @ emat @ c:irua:141723UA @ admin @ c:irua:141723 |
Serial |
4479 |
Permanent link to this record |
|
|
|
|
Author |
Albrecht, W.; Goris, B.; Bals, S.; Hutter, E.M.; Vanmaekelbergh, D.; van Huis, M.A.; van Blaaderen, A. |
|
Title |
Morphological and chemical transformations of single silica-coated CdSe/CdS nanorods upon fs-laser excitation |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Nanoscale |
Abbreviated Journal |
Nanoscale |
|
Volume |
9 |
Issue |
9 |
Pages |
4810-4818 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
Radiation-induced modifications of nanostructures are of fundamental interest and constitute a viable out-of-equilibrium approach to the development of novel nanomaterials. Herein, we investigated the structural transformation of silica-coated CdSe/CdS nanorods (NRs) under femtosecond (fs) illumination. By comparing the same nanorods before and after illumination with different fluences we found that the silica-shell did not only enhance the stability of the NRs but that the confinement of the NRs also led to novel morphological and chemical transformations. Whereas uncoated CdSe/CdS nanorods were found to sublimate under such excitations the silica-coated nanorods broke into fragments which deformed towards a more spherical shape. Furthermore, CdS decomposed which led to the formation of metallic Cd, confirmed by high-resolution electron microscopy and energy dispersive X-ray spectrometry (EDX), whereby an epitaxial interface with the remaining CdS lattice was formed. Under electron beam exposure similar transformations were found to take place which we followed in situ. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
Cambridge |
Editor |
|
|
Language |
|
Wos |
000398954800022 |
Publication Date |
2017-03-23 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2040-3364 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
7.367 |
Times cited |
4 |
Open Access |
OpenAccess |
|
Notes |
; The authors acknowledge financial support from the European Research Council under the European Unions Seventh Framework Programme (FP-2007-2013)/ERC Advanced Grant Agreement 291667 HierarSACol. The authors furthermore acknowledge financial support from the European Research Council (ERC Starting Grant 335078-COLOURATOMS and ERC Consolidator Grant 683076 NANO-INSITU). The authors also appreciate financial support from the European Union under the Seventh Framework Program (Integrated Infrastructure Initiative No. 262348 European Soft Matter Infrastructure, ESMI). This work was supported by the Flemish Fund for Scientific Research (FWO Vlaanderen) through a postdoctoral research grant to B. G. The authors furthermore thank Dave J. van den Heuvel and Hans C. Gerritsen for use of the Thorlabs powermeter. We furthermore thank Ernest van der Wee for the simulation of the confocal point spread functions. ; ecas_sara |
Approved |
Most recent IF: 7.367 |
|
Call Number |
UA @ lucian @ c:irua:142384UA @ admin @ c:irua:142384 |
Serial |
4670 |
Permanent link to this record |
|
|
|
|
Author |
Blommaerts, N.; Asapu, R.; Claes, N.; Bals, S.; Lenaerts, S.; Verbruggen, S.W. |
|
Title |
Gas phase photocatalytic spiral reactor for fast and efficient pollutant degradation |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Chemical engineering journal |
Abbreviated Journal |
Chem Eng J |
|
Volume |
316 |
Issue |
316 |
Pages |
850-856 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Sustainable Energy, Air and Water Technology (DuEL) |
|
Abstract |
Photocatalytic reactors for the degradation of gaseous organic pollutants often suffer from major limitations such as small reaction area, sub-optimal irradiation conditions and thus limited reaction rate. In this work, an alternative solution is presented that involves a glass tube coated on the inside with (silvermodified) TiO2 and spiraled around a UVA lamp. First, the spiral reactor is coated from the inside with TiO2 using an experimentally verified procedure that is optimized toward UV light transmission. This procedure is kept as simple as possible and involves a single casting step of a 1 wt% suspension of TiO2 in ethanol through the spiral. This results in a coated tube that absorbs nearly all incident UV light under the experimental conditions used. The optimized coated spiral reactor is then benchmarked to a conventional annular photoreactor of the same outer dimensions and total catalyst loading over a broad range of experimental conditions. Although residence time distribution experiments indicate slightly longer dwelling of molecules in the spiral reactor, no significant difference in by-passing of gas between the spiral reactor and the annular reactor can be claimed. Acetaldehyde degradation efficiency of 100% is obtained with the spiral reactor for a residence time as low as 60 s, whereas the annular reactor could not achieve full degradation even at 1000 s residence time. In a final case study, addition of long-term stable silver nanoparticles, protected by an ultra-thin polymer shell applied via the layer-by-layer (LbL) method, to the spiral reactor coating is shown to double the degradation efficiency and provides an interesting strategy to cope with higher pollutant concentrations without changing the overall dimensions. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000398985200089 |
Publication Date |
2017-02-08 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
1385-8947 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
6.216 |
Times cited |
30 |
Open Access |
OpenAccess |
|
Notes |
N.B. wishes to thank the University of Antwerp – Belgium for financial support. N.C. and S.B. acknowledge financial support from European Research Council (ERC Starting Grant #335078- COLOURATOM). S.W.V. acknowledges the Research Foundation – Flanders (FWO) for a postdoctoral fellowship. (ROMEO:green; preprint:; postprint:can ; pdfversion:cannot); ecas_sara |
Approved |
Most recent IF: 6.216 |
|
Call Number |
EMAT @ emat @ c:irua:140925UA @ admin @ c:irua:140925 |
Serial |
4481 |
Permanent link to this record |
|
|
|
|
Author |
Debroye, E.; Yuan, H.; Bladt, E.; Baekelant, W.; Van der Auweraer, M.; Hofkens, J.; Bals, S.; Roeffaers, M.B.J. |
|
Title |
Facile morphology-controlled synthesis of organolead iodide perovskite nanocrystals using binary capping agents |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
ChemNanoMat : chemistry of nanomaterials for energy, biology and more |
Abbreviated Journal |
Chemnanomat |
|
Volume |
3 |
Issue |
3 |
Pages |
223-227 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
Controlling the morphology of organolead halide perovskite crystals is crucial to a fundamental understanding of the materials and to tune their properties for device applications. Here, we report a facile solution-based method for morphology-controlled synthesis of rod-like and plate-like organolead halide perovskite nanocrystals using binary capping agents. The morphology control is likely due to an interplay between surface binding kinetics of the two capping agents at different crystal facets. By high-resolution scanning transmission electron microscopy, we show that the obtained nanocrystals are monocrystalline. Moreover, long photoluminescence decay times of the nanocrystals indicate long charge diffusion lengths and low trap/defect densities. Our results pave the way for large-scale solution synthesis of organolead halide perovskite nanocrystals with controlled morphology for future device applications. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000399604300003 |
Publication Date |
2017-01-18 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2199-692x |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
2.937 |
Times cited |
19 |
Open Access |
OpenAccess |
|
Notes |
; We acknowledge financial support from the Research Foundation-Flanders (FWO, grant G.0197.11, G.0962.13, G0B39.15, postdoctoral fellowship to E. D. and H. Y.), KU Leuven Research Fund (C14/15/053), the Flemish government through long term structural funding Methusalem (CASAS2, Meth/15/04), the Hercules foundation (HER/11/14), the Belgian Federal Science Policy Office (IAP-PH05), the EC through the Marie Curie ITN project iSwitch (GA-642196) and the ERC project LIGHT (GA307523). S. B. acknowledges financial support from European Research Council (ERC Starting Grant # 335078-COLOURATOMS). E. B. gratefully acknowledges financial support by the Flemish Fund for Scientific Research (FWO Vlaanderen). ; ecas_Sara |
Approved |
Most recent IF: 2.937 |
|
Call Number |
UA @ lucian @ c:irua:143678UA @ admin @ c:irua:143678 |
Serial |
4656 |
Permanent link to this record |
|
|
|
|
Author |
Bueken, B.; Van Velthoven, N.; Willhammar, T.; Stassin, T.; Stassen, I.; Keen, D.A.; Baron, G.V.; Denayer, J.F.M.; Ameloot, R.; Bals, S.; De Vos, D.; Bennett, T.D. |
|
Title |
Gel-based morphological design of zirconium metal-organic frameworks |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Chemical science |
Abbreviated Journal |
Chem Sci |
|
Volume |
8 |
Issue |
8 |
Pages |
3939-3948 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
The ability of metal-organic frameworks (MOFs) to gelate under specific synthetic conditions opens up new opportunities in the preparation and shaping of hierarchically porous MOF monoliths, which could be directly implemented for catalytic and adsorptive applications. In this work, we present the first examples of xero-or aerogel monoliths consisting solely of nanoparticles of several prototypical Zr4+-based MOFs: UiO-66-X (X – H, NH2, NO2, (OH)(2)), UiO-67, MOF-801, MOF-808 and NU-1000. High reactant and water concentrations during synthesis were observed to induce the formation of gels, which were converted to monolithic materials by drying in air or supercritical CO2. Electron microscopy, combined with N-2 physisorption experiments, was used to show that irregular nanoparticle packing leads to pure MOF monoliths with hierarchical pore systems, featuring both intraparticle micropores and interparticle mesopores. Finally, UiO-66 gels were shaped into monolithic spheres of 600 mm diameter using an oil-drop method, creating promising candidates for packed-bed catalytic or adsorptive applications, where hierarchical pore systems can greatly mitigate mass transfer limitations. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
Royal Society of Chemistry |
Place of Publication |
Cambridge |
Editor |
|
|
Language |
|
Wos |
000400553000077 |
Publication Date |
2017-03-23 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2041-6520 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
8.668 |
Times cited |
168 |
Open Access |
OpenAccess |
|
Notes |
; B. B., T. S. and I. S. acknowledge the FWO Flanders (doctoral and post-doctoral grants). T. W. acknowledges a post-doctoral grant from the Swedish Research Council. T. D. B. acknowledges the Royal Society (University Research Fellowship) and Trinity Hall (University of Cambridge) for funding. S. B. and D. D. V. are grateful for funding by Belspo (IAP 7/05 P6/27) and by the FWO Flanders. D. D. V. further acknowledges funding from the European Research Council (project H-CCAT). S. B. acknowledges financial support from the European Research Council (ERC Starting Grant #335078-COLOURATOMS). The authors acknowledge Arnau Carne and Shuhei Furukawa for assistance with supercritical CO<INF>2</INF> extraction, and Charles Ghesquiere for assistance in synthesis. ; Ecas_Sara |
Approved |
Most recent IF: 8.668 |
|
Call Number |
UA @ lucian @ c:irua:152643UA @ admin @ c:irua:152643 |
Serial |
5143 |
Permanent link to this record |
|
|
|
|
Author |
Mernissi Cherigui, E.A.; Sentosun, K.; Bouckenooge, P.; Vanrompay, H.; Bals, S.; Terryn, H.; Ustarroz, J. |
|
Title |
A Comprehensive Study of the Electrodeposition of Nickel Nanostructures from Deep Eutectic Solvents: Self-Limiting Growth by Electrolysis of Residual Water |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
The journal of physical chemistry: C : nanomaterials and interfaces |
Abbreviated Journal |
J Phys Chem C |
|
Volume |
121 |
Issue |
121 |
Pages |
9337-9347 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
The electrodeposition of nickel nanostructures on glassy carbon was investigated in 1:2 choline chloride – urea (1:2 ChCl-U) deep eutectic solvent (DES). By combining electrochemical techniques with ex-situ FE-SEM, XPS, HAADF-STEM and EDX, the electrochemical processes occurring during nickel deposition were better understood. Special attention was given to the interaction between the solvent and the growing nickel nanoparticles. The application of a suffciently negative potential results into the electrocatlytic hydrolisis of residual water in the DES, which leads to the formation of a mixed layer of Ni/Ni(OH)2(ads). In addition, hydrogen bonds between hydroxide species and the DES components could be formed, quenching the growth of the nickel clusters favouring their aggregation. Due to these processes, a highly dense distribution of nickel nanostructures can be obtained within a wide potential range. Understanding the role of residual water and the interactions at the interface during metal electrodeposition from DESs is essential to produce supported nanostructures in a controllable way for a broad range of applications and technologies. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000400881100027 |
Publication Date |
2017-04-12 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
1932-7447 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
4.536 |
Times cited |
66 |
Open Access |
OpenAccess |
|
Notes |
E.A. Mernissi Cherigui acknowledges funding from the Fonds Wetenschappelijk Onderzoek in Flanders (FWO, research project G019014N). S. Bals acknowledges funding from the European Research Council (Starting Grant No. COLOURATOMS 335078). H.V. gratefully acknowledges financial support by the Flemish Fund for Scientific Research (FWO Vlaanderen). Finally, J. Ustarroz acknowledges funding from the Fonds Wetenschappelijk Onderzoek in Flanders (FWO, postdoctoral grant 12I7816N). (ROMEO:white; preprint:; postprint:restricted 12 months embargo; pdfversion:cannot); ECAS_Sara |
Approved |
Most recent IF: 4.536 |
|
Call Number |
EMAT @ emat @ c:irua:142208UA @ admin @ c:irua:142208 |
Serial |
4551 |
Permanent link to this record |
|
|
|
|
Author |
Alania, M.; Altantzis, T.; De Backer, A.; Lobato, I.; Bals, S.; Van Aert, S. |
|
Title |
Depth sectioning combined with atom-counting in HAADF STEM to retrieve the 3D atomic structure |
Type |
A1 Journal article |
|
Year |
2016 |
Publication |
Ultramicroscopy |
Abbreviated Journal |
Ultramicroscopy |
|
Volume |
177 |
Issue |
177 |
Pages |
36-42 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Aberration correction in scanning transmission electron microscopy (STEM) has greatly improved the lateral and depth resolution. When using depth sectioning, a technique during which a series of images is recorded at different defocus values, single impurity atoms can be visualised in three dimensions. In this paper, we investigate new possibilities emerging when combining depth sectioning and precise atom-counting in order to reconstruct nanosized particles in three dimensions. Although the depth resolution does not allow one to precisely locate each atom within an atomic column, it will be shown that the depth location of an atomic column as a whole can be measured precisely. In this manner, the morphology of a nanoparticle can be reconstructed in three dimensions. This will be demonstrated using simulations and experimental data of a gold nanorod. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000401219800006 |
Publication Date |
2016-11-09 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0304-3991 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
2.843 |
Times cited |
13 |
Open Access |
OpenAccess |
|
Notes |
The authors acknowledge financial support from the European Union under the Seventh Framework Program under a contract for an Integrated Infrastructure Initiative. Reference No. 312483-ESTEEM2. S. Bals acknowledges funding from the European Research Council (Starting Grant No. COLOURATOMS 335078). The authors acknowledge financial support from the Research Foundation Flanders (FWO, Belgium) through project fundings (G.0374.13N, G.0369.15N and G.0368.15N) and a post-doctoral grant to A. De Backer and T. Altantzis. The authors are grateful to Professor Luis M. Liz-Marzán for providing the sample.; ECAS_Sara; (ROMEO:green; preprint:; postprint:can ; pdfversion:cannot); |
Approved |
Most recent IF: 2.843 |
|
Call Number |
EMAT @ emat @ c:irua:138015UA @ admin @ c:irua:138015 |
Serial |
4316 |
Permanent link to this record |
|
|
|
|
Author |
Peters, J.L.; van den Bos, K.H.W.; Van Aert, S.; Goris, B.; Bals, S.; Vanmaekelbergh, D. |
|
Title |
Ligand-Induced Shape Transformation of PbSe Nanocrystals |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Chemistry of materials |
Abbreviated Journal |
Chem Mater |
|
Volume |
29 |
Issue |
29 |
Pages |
4122-4128 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
We present a study of the relation between the surface chemistry and nanocrystal shape of PbSe nanocrystals with a variable Pb-to-Se stoichiometry and density of oleate ligands. The oleate ligand density and binding configuration are monitored by nuclear magnetic resonance and Fourier transform infrared absorbance spectroscopy, allowing us to quantify the number of surface-attached ligands per NC and the nature of the surface−Pb−oleate configuration. The three-dimensional shape of the PbSe nanocrystals is obtained from high-angle annular dark field scanning transmission electron microscopy combined with an atom counting method. We show that the enhanced oleate capping results in a stabilization and extension of the {111} facets, and a crystal shape transformation from a truncated nanocube to a truncated octahedron. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000401221700034 |
Publication Date |
2017-05-09 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0897-4756 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
9.466 |
Times cited |
45 |
Open Access |
OpenAccess |
|
Notes |
D.V. acknowledges the European Research Council, ERC advanced grant, Project 692691-First Step, for financial support. We also acknowledge the Dutch FOM programme “Designing Dirac carriers in honeycomb semiconductor superlattices” (FOM Program 152) for financial support. The authors gratefully acknowledge funding from the Research Foundation Flanders (G.036915, G.037413, and funding of a Ph.D. research grant to K.H.W.v.d.B. and a postdoctoral grant to B.G.). S.B. acknowledges the European Research Council, ERC Grant 335078-Colouratom. (ROMEO:white; preprint:; postprint:restricted 12 months embargo; pdfversion:cannot); ECAS_Sara |
Approved |
Most recent IF: 9.466 |
|
Call Number |
EMAT @ emat @ c:irua:143750 c:irua:142983UA @ admin @ c:irua:143750 |
Serial |
4571 |
Permanent link to this record |
|
|
|
|
Author |
Ustarroz, J.; Geboes, B.; Vanrompay, H.; Sentosun, K.; Bals, S.; Breugelmans, T.; Hubin, A. |
|
Title |
Electrodeposition of Highly Porous Pt Nanoparticles Studied by Quantitative 3D Electron Tomography: Influence of Growth Mechanisms and Potential Cycling on the Active Surface Area |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
ACS applied materials and interfaces |
Abbreviated Journal |
Acs Appl Mater Inter |
|
Volume |
9 |
Issue |
9 |
Pages |
16168-16177 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Applied Electrochemistry & Catalysis (ELCAT) |
|
Abstract |
Nanoporous Pt nanoparticles (NPs) are promising fuel cell catalysts due to their large surface area and increased electrocatalytic activity towards the oxygen reduction reaction (ORR). Herein, we report on the infuence of the growth mechanisms on the surface properties of electrodeposited Pt dendritic NPs with large surface areas. The electrochemically active surface was studied by hydrogen underpotential deposition (HUPD) and compared for the rst time to high angle annular dark eld scanning transmission electron microscopy (HAADF-STEM) quantitative 3D electron tomography of individual nanoparticles. Large nucleation overpotential leads to a large surface coverage of Pt roughened spheroids, which provide large roughness factor (Rf ) but low mass-specic electrochemically active surface area (EASA). Lowering the nucleation overpotential leads to highly porous Pt NPs with pores protruding to the center of the structure. At the expense of smaller Rf , the obtained EASA values of these structures are in the range of these of large surface area supported fuel cell catalysts. The active surface area of the Pt dendritic NPs was measured by electron tomography and it was found that the potential cycling in the H adsorption/desorption and Pt oxidation/reduction region, which is generally performed to determine the EASA, leads to a signicant reduction of that surface area due to a partial collapse of their dendritic and porous morphology. Interestingly, the extrapolation of the microscopic tomography results to macroscopic electrochemical parameters indicated that the surface properties measured by H UPD are comparable to the values measured on individual NPs by electron tomography after the degradation caused by the H UPD measurement. These results highlight that the combination of electrochemical and quantitative 3D surface analysis techniques is essential to provide insights into the surface properties, the electrochemical stability and, hence, the applicability of these materials. Moreover, it indicates that care must be taken with widely used electrochemical methods of surface area determination, especially in the case of large surface area and possibly unstable nanostructures, since the measured surface can be strongly aected by the measurement itself. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000401782500028 |
Publication Date |
2017-04-18 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
1944-8244 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
7.504 |
Times cited |
24 |
Open Access |
OpenAccess |
|
Notes |
Jon Ustarroz acknowledges funding from the Fonds Wetenschappelijk Onderzoek in Flanders (FWO, postdoctoral grant 12I7816N). S. Bals acknowledges funding from the European Research Council (Starting Grant No. COLOURATOMS 335078). S.B. and T.B. acknowledge the University of Antwerp for nancial support in the frame of a GOA project. H.V. gratefully acknowledges nancial support by the Flemish Fund for Scientic Research (FWO Vlaanderen). All the authors acknowledge Laurens Stevaert for his contribution to the work presented in this manuscript. (ROMEO:white; preprint:; postprint:restricted 12 months embargo; pdfversion:cannot); ECAS_Sara |
Approved |
Most recent IF: 7.504 |
|
Call Number |
EMAT @ emat @ c:irua:142345UA @ admin @ c:irua:142345 |
Serial |
4552 |
Permanent link to this record |
|
|
|
|
Author |
Berthold, T.; Castro, C.R.; Winter, M.; Hoerpel, G.; Kurttepeli, M.; Bals, S.; Antonietti, M.; Fechler, N. |
|
Title |
Tunable nitrogen-doped carbon nanoparticles from tannic acid and urea and their potential for sustainable soots |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
ChemNanoMat : chemistry of nanomaterials for energy, biology and more |
Abbreviated Journal |
Chemnanomat |
|
Volume |
3 |
Issue |
3 |
Pages |
311-318 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
Nano-sized nitrogen-doped carbon spheres are synthesized from two cheap, readily available and sustainable precursors: tannic acid and urea. In combination with a polymer structuring agent, nitrogen content, sphere size and the surface (up to 400 m(2)g(-1)) can be conveniently tuned by the precursor ratio, temperature and structuring agent content. Because the chosen precursors allow simple oven synthesis and avoid harsh conditions, this carbon nanosphere platform offers a more sustainable alternative to classical soots, for example, as printing pigments or conduction soots. The carbon spheres are demonstrated to be a promising as conductive carbon additive in anode materials for lithium ion batteries. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000403299200006 |
Publication Date |
2017-03-10 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2199-692x |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
2.937 |
Times cited |
14 |
Open Access |
OpenAccess |
|
Notes |
; S.B. is grateful for funding by the European Research Council (ERC starting grant # 335078-COLOURATOMS). ; ecas_Sara |
Approved |
Most recent IF: 2.937 |
|
Call Number |
UA @ lucian @ c:irua:144287UA @ admin @ c:irua:144287 |
Serial |
4699 |
Permanent link to this record |
|
|
|
|
Author |
Zhong, Z.; Goris, B.; Schoenmakers, R.; Bals, S.; Batenburg, K.J. |
|
Title |
A bimodal tomographic reconstruction technique combining EDS-STEM and HAADF-STEM |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Ultramicroscopy |
Abbreviated Journal |
Ultramicroscopy |
|
Volume |
174 |
Issue |
174 |
Pages |
35-45 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
A three-dimensional (3D) chemical characterization of nanomaterials can be obtained using tomography based on high angle annular dark field (HAADF) scanning transmission electron microscopy (STEM) or energy dispersive X-ray spectroscopy (EDS) STEM. These two complementary techniques have both advantages and disadvantages. The Z-contrast images have good image quality but lack robustness in the compositional analysis, while the elemental maps give more element-specific information, but at a low signal-to-noise ratio and a longer exposure time. Our aim is to combine these two types of complementary information in one single tomographic reconstruction process. Therefore, an imaging model is proposed combining both HAADF-STEM
and EDS-STEM. Based on this model, the elemental distributions can be reconstructed using both types of information simultaneously during the reconstruction process. The performance of the new technique is evaluated using simulated data and real experimental data. The results demonstrate that combining two imaging modalities leads to tomographic reconstructions with suppressed noise and enhanced contrast. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000403342200005 |
Publication Date |
2016-12-11 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0304-3991 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
2.843 |
Times cited |
26 |
Open Access |
OpenAccess |
|
Notes |
This research is supported by the Dutch Technology Foundation STW (http://www.stw.nl/), which is part of the Netherlands Organization for Scientific Research (NWO), and which is partly funded by the Ministry of Economic Affairs, Agriculture and Innovation under project number 13314. It is also supported by the Flemish research foundation (FWO Vlaanderen) by project funding (G038116N) and a postdoctoral research grant to B.G. Funding from the European Research Council (Starting Grant No. COLOURATOMS 335078) is acknowledged by S.B. The authors would like to thank Dr. Bernd Rieger and Dr. Richard Aveyard for useful discussions, and Prof. Dr. Luis M. Liz-Marzan for providing the investigated samples. We also acknowledge COST Action MP1207 for networking support. (ROMEO:green; preprint:; postprint:can ; pdfversion:cannot); saraecas; ECAS_Sara; |
Approved |
Most recent IF: 2.843 |
|
Call Number |
EMAT @ emat @ c:irua:141719UA @ admin @ c:irua:141719 |
Serial |
4484 |
Permanent link to this record |
|
|
|
|
Author |
Zhuge, X.; Jinnai, H.; Dunin-Borkowski, R.E.; Migunov, V.; Bals, S.; Cool, P.; Bons, A.-J.; Batenburg, K.J. |
|
Title |
Automated discrete electron tomography – Towards routine high-fidelity reconstruction of nanomaterials |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Ultramicroscopy |
Abbreviated Journal |
Ultramicroscopy |
|
Volume |
175 |
Issue |
175 |
Pages |
87-96 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT); Laboratory of adsorption and catalysis (LADCA) |
|
Abstract |
Electron tomography is an essential imaging technique for the investigation of morphology and 3D structure of nanomaterials. This method, however, suffers from well-known missing wedge artifacts due to a restricted tilt range, which limits the objectiveness, repeatability and efficiency of quantitative structural analysis. Discrete tomography represents one of the promising reconstruction techniques for materials science, potentially capable of delivering higher fidelity reconstructions by exploiting the prior knowledge of the limited number of material compositions in a specimen. However, the application of discrete tomography to practical datasets remains a difficult task due to the underlying challenging mathematical problem. In practice, it is often hard to obtain consistent reconstructions from experimental datasets. In addition, numerous parameters need to be tuned manually, which can lead to bias and non-repeatability. In this paper, we present the application of a new
iterative reconstruction technique, named TVR-DART, for discrete electron tomography. The technique is capable of consistently delivering reconstructions with significantly reduced missing wedge artifacts for a variety of challenging data and imaging conditions, and can automatically estimate its key parameters. We describe the principles of the technique and apply it to datasets from three different types of samples acquired under diverse imaging modes. By further reducing the available tilt range and number of projections, we show that the
proposed technique can still produce consistent reconstructions with minimized missing wedge artifacts. This new development promises to provide the electron microscopy community with an easy-to-use and robust tool for high-fidelity 3D characterization of nanomaterials. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000403342500008 |
Publication Date |
2017-01-24 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0304-3991 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
2.843 |
Times cited |
22 |
Open Access |
OpenAccess |
|
Notes |
This work has been supported in part by the Stichting voor de Technische Wetenschappen (STW) through a personal grant (Veni,13610), and was in part by ExxonMobil Chemical Europe Inc. The authors further acknowledge financial support from the University of Antwerp through BOF GOA funding. S.B. acknowledges financial support from the European Research Council (ERC Starting Grant #335078-COLOURATOMS). R.D.B. is grateful for funding from the European Research Council under the European Union's Seventh Framework Programme (FP7/2007–2013)/ ERC grant agreement number 320832. Thomas Altantzis is gratefully acknowledged for acquiring the Anatase nanosheets dataset. (ROMEO:green; preprint:; postprint:can ; pdfversion:cannot); saraecas; ECAS_Sara; |
Approved |
Most recent IF: 2.843 |
|
Call Number |
EMAT @ emat @ c:irua:141218UA @ admin @ c:irua:141218 |
Serial |
4485 |
Permanent link to this record |
|
|
|
|
Author |
De Backer, A.; Jones, L.; Lobato, I.; Altantzis, T.; Goris, B.; Nellist, P.D.; Bals, S.; Van Aert, S. |
|
Title |
Three-dimensional atomic models from a single projection using Z-contrast imaging: verification by electron tomography and opportunities |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Nanoscale |
Abbreviated Journal |
Nanoscale |
|
Volume |
9 |
Issue |
9 |
Pages |
8791-8798 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
In order to fully exploit structure–property relations of nanomaterials, three-dimensional (3D) characterization at the atomic scale is often required. In recent years, the resolution of electron tomography has reached the atomic scale. However, such tomography typically requires several projection images demanding substantial electron dose. A newly developed alternative circumvents this by counting the number of atoms across a single projection. These atom counts can be used to create an initial atomic model with which an energy minimization can be applied to obtain a relaxed 3D reconstruction of the nanoparticle. Here, we compare, at the atomic scale, this single projection reconstruction approach with tomography and find an excellent agreement. This new approach allows for the characterization of beam-sensitive materials or where the acquisition of a tilt series is impossible. As an example, the utility is illustrated by the 3D atomic scale characterization of a nanodumbbell on an in situ heating holder of limited tilt range. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000404614700031 |
Publication Date |
2017-06-09 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2040-3364 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
7.367 |
Times cited |
33 |
Open Access |
OpenAccess |
|
Notes |
The authors gratefully acknowledge funding from the Research Foundation Flanders (FWO, Belgium) through project fundings (G.0374.13N, G.0369.15N, G.0368.15N, and WO.010.16N) and postdoctoral grants to T. Altantzis, A. De Backer, and B. Goris. S. Bals acknowledges financial support from the European Research Council (Starting Grant No. COLOURATOM 335078). Funding from the European Union Seventh Framework Programme under Grant Agreement 312483 – ESTEEM2 (Integrated Infrastructure Initiatieve-I3) is acknowledged. The authors would also like to thank Luis Liz-Marzán, Marek Grzelczak, and Ana Sánchez-Iglesias for sample provision. (ROMEO:yellow; preprint:; postprint:restricted ; pdfversion:cannot); saraecas; ECAS_Sara; |
Approved |
Most recent IF: 7.367 |
|
Call Number |
EMAT @ emat @ c:irua:144436UA @ admin @ c:irua:144436 |
Serial |
4617 |
Permanent link to this record |
|
|
|
|
Author |
Schnepf, M.J.; Mayer, M.; Kuttner, C.; Tebbe, M.; Wolf, D.; Dulle, M.; Altantzis, T.; Formanek, P.; Förster, S.; Bals, S.; König, T.A.F.; Fery, A. |
|
Title |
Nanorattles with tailored electric field enhancement |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Nanoscale |
Abbreviated Journal |
Nanoscale |
|
Volume |
9 |
Issue |
9 |
Pages |
9376-9385 |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
Abstract |
Nanorattles are metallic core–shell particles with core and shell separated by a dielectric spacer. These
nanorattles have been identified as a promising class of nanoparticles, due to their extraordinary high
electric-field enhancement inside the cavity. Limiting factors are reproducibility and loss of axial symmetry
owing to the movable metal core; movement of the core results in fluctuation of the nanocavity dimensions
and commensurate variations in enhancement factor. We present a novel synthetic approach for
the robust fixation of the central gold rod within a well-defined box, which results in an axisymmetric
nanorattle. We determine the structure of the resulting axisymmetric nanorattles by advanced transmission
electron microscopy (TEM) and small-angle X-ray scattering (SAXS). Optical absorption and scattering
cross-sections obtained from UV-vis-NIR spectroscopy quantitatively agree with finite-difference
time-domain (FDTD) simulations based on the structural model derived from SAXS. The predictions of
high and homogenous field enhancement are evidenced by scanning TEM electron energy loss spectroscopy
(STEM-EELS) measurement on single-particle level. Thus, comprehensive understanding of
structural and optical properties is achieved for this class of nanoparticles, paving the way for photonic
applications where a defined and robust unit cell is crucial. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000405387100015 |
Publication Date |
2017-06-22 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2040-3364 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
7.367 |
Times cited |
69 |
Open Access |
OpenAccess |
|
Notes |
This study was funded by the European Research Council under grant Template-assisted assembly of METAmaterials using MECHanical instabilities (METAMECH) ERC-2012-StG 306686. This work was also supported by the Deutsche Forschungsgemeinschaft (DFG) within the Cluster of Excellence ‘Center for Advancing Electronics Dresden’ (cfaed). M. T. wants to acknowledge funding by the Elite Network of Bavaria, the Bavarian Ministry of State according to the Bavarian elite promotion act (BayEFG), as well as the Alexander von Humboldt Foundation for a Feodor-Lynen Research Fellowship. S. B. acknowledges financial support from the European Research Council (Starting Grant No. COLOURATOM 335078) and T. A. acknowledges funding from the Research Foundation Flanders (FWO, Belgium) through a postdoctoral grant. We thank Ken Harris from the National Research Council Canada for valuable discussion of the manuscript. (ROMEO:yellow; preprint:; postprint:restricted ; pdfversion:cannot); saraecas; ECAS_Sara; |
Approved |
Most recent IF: 7.367 |
|
Call Number |
EMAT @ emat @ c:irua:144797UA @ admin @ c:irua:144797 |
Serial |
4631 |
Permanent link to this record |
|
|
|
|
Author |
Ata, I.; Ben Dkhil, S.; Pfannmoeller, M.; Bals, S.; Duche, D.; Simon, J.-J.; Koganezawa, T.; Yoshimoto, N.; Videlot-Ackermann, C.; Margeat, O.; Ackermann, J.; Baeuerle, P. |
|
Title |
The influence of branched alkyl side chains in A-D-A oligothiophenes on the photovoltaic performance and morphology of solution-processed bulk-heterojunction solar cells |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Organic chemistry frontiers : an international journal of organic chemistry |
Abbreviated Journal |
Org Chem Front |
|
Volume |
4 |
Issue |
4 |
Pages |
1561-1573 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Besides providing sufficient solubility, branched alkyl chains also affect the film-forming and packing properties of organic semiconductors. In order to avoid steric hindrance as it is present in wide-spread alkyl chains comprising a branching point position at the C2-position, i.e., 2-ethylhexyl, the branching point can be moved away from the pi-conjugated backbone. In this report, we study the influence of the modification of the branching point position from the C2-position in 2-hexyldecylamine (1) to the C4-position in 4-hexyldecylamine (2) connected to the central dithieno[3,2-b: 2', 3'-d] pyrrole (DTP) moiety in a well-studied A-D-A oligothiophene on the optoelectronic properties and photovoltaic performance in solution- processed bulk heterojunction solar cells (BHJSCs) with [6,6]-phenyl-C71-butyric acid methyl ester (PC71BM) as the acceptor material. Post-treatment of the photoactive layers is performed via solvent vapor annealing (SVA) in order to improve the film microstructure of the bulk heterojunction. The time evolution of nanoscale morphological changes is followed by combining scanning transmission electron microscopy with low-energy-loss spectroscopic imaging (STEM-SI), solid-state absorption spectroscopy, and two-dimensional grazing incidence X-ray diffraction (2D-GIXRD). Our results show an improvement of the photovoltaic performance that is dependent on the branching point position in the donor oligomer. Optical spacers are utilized to increase light absorption inside the co-oligomer 2-based BHJSCs leading to increased power conversion efficiencies (PCEs) of 8.2% when compared to the corresponding co-oligomer 1-based devices. A STEM-SI analysis of the respective device cross-sections of active layers containing 1 and 2 as donor materials indeed reveals significant differences in their respective active layer morphologies. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
RSC Publishing |
Place of Publication |
London |
Editor |
|
|
Language |
|
Wos |
000406374800013 |
Publication Date |
2017-05-02 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
2052-4129 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
4.955 |
Times cited |
24 |
Open Access |
OpenAccess |
|
Notes |
; We acknowledge financial support by the European Commission under the project “SUNFLOWER” (FP7-ICT-2011-7, grant number: 287594) and S.B. acknowledges the ERC Starting Grant Colouratoms (335078). ; |
Approved |
Most recent IF: 4.955 |
|
Call Number |
UA @ lucian @ c:irua:145176UA @ admin @ c:irua:145176 |
Serial |
4727 |
Permanent link to this record |
|
|
|
|
Author |
Mahr, C.; Kundu, P.; Lackmann, A.; Zanaga, D.; Thiel, K.; Schowalter, M.; Schwan, M.; Bals, S.; Wittstock, A.; Rosenauer, A. |
|
Title |
Quantitative determination of residual silver distribution in nanoporous gold and its influence on structure and catalytic performance |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Journal of catalysis |
Abbreviated Journal |
J Catal |
|
Volume |
352 |
Issue |
352 |
Pages |
52-58 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
Abstract |
Large efforts have been made trying to understand the origin of the high catalytic activity of dealloyed nanoporous gold as a green catalyst for the selective promotion of chemical reactions at low temperatures. Residual silver, left in the sample after dealloying of a gold-silver alloy, has been shown to have a strong influence on the activity of the catalyst. But the question of how the silver is distributed within the porous structure has not finally been answered yet. We show by quantitative energy dispersive X-ray tomography measurements that silver forms clusters that are distributed irregularly, both on the surface and inside the ligaments building up the porous structure. Furthermore, we find that the role of the residual silver is ambiguous. Whereas CO oxidation is supported by more residual silver, methanol oxidation to methyl formate is hindered. Structural characterisation reveals larger ligaments and pores for decreasing residual silver concentration. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000408299600006 |
Publication Date |
2017-05-29 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
0021-9517 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
6.844 |
Times cited |
42 |
Open Access |
OpenAccess |
|
Notes |
This work was supported by the Deutsche Forschungsgemeinschaft (DFG) under contracts no. RO2057/12-1 (SP 6) and WI4497/1-1 (SP 2) within the research unit FOR2213 (www.nagocat. de) and the European Research Council (ERC Starting Grant No. 335078-COLOURATOMS). (ROMEO:green; preprint:; postprint:can ; pdfversion:cannot); ecas_sara |
Approved |
Most recent IF: 6.844 |
|
Call Number |
EMAT @ emat @c:irua:144434UA @ admin @ c:irua:144434 |
Serial |
4623 |
Permanent link to this record |
|
|
|
|
Author |
Garzia Trulli, M.; Claes, N.; Pype, J.; Bals, S.; Baert, K.; Terryn, H.; Sardella, E.; Favia, P.; Vanhulsel, A. |
|
Title |
Deposition of aminosilane coatings on porous Al2O3microspheres by means of dielectric barrier discharges |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Plasma processes and polymers |
Abbreviated Journal |
Plasma Process Polym |
|
Volume |
14 |
Issue |
14 |
Pages |
1600211 |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT); Laboratory of adsorption and catalysis (LADCA) |
|
Abstract |
Advances in the synthesis of porous microspheres and in their functionalization are increasing the interest in applications of alumina. This paper deals with coatings plasma deposited from 3-aminopropyltriethoxysilane by means of dielectric barrier discharges on alumina porous microspheres, shaped by a vibrational droplet coagulation technique. Aims of the work are the functionalization of the particles with active amino groups, as well as the evaluation of their surface coverage and of the penetration of the coatings into their pores. A multi-diagnostic approach was used for the chemical/morphological characterization of the particles. It was found that 5 min exposure to plasma discharges promotes the deposition of homogeneous coatings onto the microspheres and within their pores, down to 1 μm. |
|
Address |
|
|
Corporate Author |
|
Thesis |
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
Language |
|
Wos |
000410773200003 |
Publication Date |
2017-01-05 |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
ISSN |
1612-8850 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
Impact Factor |
2.846 |
Times cited |
8 |
Open Access |
OpenAccess |
|
Notes |
The technical assistance of the VITO staff (Materials Dpt.) is gratefully acknowledged, especially D. Havermans, E. Van Hoof, R. Kemps (SEM-EDX), and A. De Wilde (Hg Porosimetry). Drs. S. Mullens and G. Scheltjens are kindly acknowledged for constructive discussions. Strategic Initiative Materials in Flanders (SIM) is gratefully acknowledged for its financial support. This research was carried out in the framework of the SIM-TRAP program (Tools for rational processing of nano-particles: controlling and tailoring nanoparticle based or nanomodified particle based materials). N. Claes and S. Bals acknowledge financial support from European Research Council (ERC Starting Grant #335078-COLOURATOM). (ROMEO:white; preprint:; postprint:restricted ; pdfversion:cannot); saraecas; ECAS_Sara; |
Approved |
Most recent IF: 2.846 |
|
Call Number |
EMAT @ emat @ c:irua:139511UA @ admin @ c:irua:139511 |
Serial |
4342 |
Permanent link to this record |