Abstract: Plasma catalysis is gaining increasing interest, but the underlying mechanisms are far from understood. Different catalyst materials will have different chemical effects, but in addition, they might also have different dielectric constants, which will affect surface charging, and thus the plasma behavior. In this work, we demonstrate that surface charging plays an important role in the streamer propagation and discharge enhancement inside catalyst pores, and in the plasma distribution along the dielectric surface, and this role greatly depends on the dielectric constant of the material. For εr50, surface charging causes the plasma to spread along the dielectric surface and inside the pores, leading to deeper plasma streamer penetration, while for εr>50 or for metallic coatings, the discharge is more localized, due to very weak surface charging. In addition, at εr=50, the significant surface charge density near the pore entrance causes a large potential drop at the sharp pore edges, which induces a strong electric field and results in most pronounced plasma enhancement near the pore entrance.

Abstract: In this work we study energy transport in a gliding arc discharge with two diverging flat
electrodes in argon gas at atmospheric pressure. The discharge is ignited at the shortest electrode
gap and it is pushed downstream by a forced gas flow. The current values considered are
relatively low and therefore a non-equilibrium plasma is produced. We consider two cases, i.e.
with high and low discharge current (28 mA and 2.8mA), and a constant gas flow of 10 lmin −1 ,
with a significant turbulent component to the velocity. The study presents an analysis of the
various energy transport mechanisms responsible for the redistribution of Joule heating to the
plasma species and the moving background gas. The objective of this work is to provide a
general understanding of the role of the different energy transport mechanisms in arc formation
and sustainment, which can be used to improve existing or new discharge designs. The work is
based on a three-dimensional numerical model, combining a fluid plasma model, the shear stress
transport Reynolds averaged Navier–Stokes turbulent gas flow model, and a model for gas
thermal balance. The obtained results show that at higher current the discharge is constricted
within a thin plasma column several hundred kelvin above room temperature, while in the low-
current discharge the combination of intense convective cooling and low Joule heating prevents
discharge contraction and the plasma column evolves to a static non-moving diffusive plasma,
continuously cooled by the flowing gas. As a result, the energy transport in the two cases is
determined by different mechanisms. At higher current and a constricted plasma column, the
plasma column is cooled mainly by turbulent transport, while at low current and an unconstricted
plasma, the major cooling mechanism is energy transport due to non-turbulent gas convection. In
general, the study also demonstrates the importance of turbulent energy transport in
redistributing the Joule heating in the arc and its significant role in arc cooling and the formation
of the gas temperature profile. In general, the turbulent energy transport lowers the average gas
temperature in the arc, thus allowing additional control of thermal non-equilibrium in the
discharge.

Abstract: Plasma catalysis is gaining increasing interest for various environmental applications. Catalytic
material can be inserted in different shapes in the plasma, e.g., as pellets, (coated) beads, but also
as honeycomb monolith and 3DFD structures, also called ‘structured catalysts’, which have high
mass and heat transfer properties. In this work, we examine the streamer discharge propagation
and the interaction between plasma and catalysts, inside the channels of such structured catalysts,
by means of a two-dimensional particle-in-cell/Monte Carlo collision model. Our results reveal
that plasma streamers behave differently in various structured catalysts. In case of a honeycomb
structure, the streamers are limited to only one channel, with low or high plasma density when
the channels are parallel or perpendicular to the electrodes, respectively. In contrast, in case of a
3DFD structure, the streamers can distribute to different channels, causing discharge
enhancement due to surface charging on the dielectric walls of the structured catalyst, and
especially giving rise to a broader plasma distribution. The latter should be beneficial for plasma
catalysis applications, as it allows a larger catalyst surface area to be exposed to the plasma.

Abstract: The structural modification of ssDNA-based aptamers upon specific binding of its target molecule leads to changes of the charge-transfer resistance (Rct) of a negatively-charged free-diffusing redox probe. The aptamer adopts a structure due to self-hybridization which is stabilized using profalvine as intercalator. The pre-organized aptamer structure is used to detect chloramphenicol (CAP) requiring a substantial change of the aptamer structure indicated by a CAP concentration dependent increase in the Rct values. Pre-incubation of the aptamer-modified electrode with an intercalator allows for the modulation of the aptamer/target interaction and hence for a modulation of the CAP-dependent variation of the Rct values.

Abstract: Buildings are responsible for 40% of our worldwide energy consumption and 50% of this energy is converted for Heating Ventilation Air Conditioning (HVAC) systems in buildings. The increasing share of renewable energy production required to make the transition towards a carbon neutral energy system challenges the stability of the grid. Through demand response it becomes possible to activate these systems in support of grid balancing. However, this flexibility is currently not rewarded in the market. We simulate a domestic water heater participating in the balancing of the electricity net and calculated the revenue from this action. We simulate a water heater in connection with an Economic Model Predictive Controller (EMPC) which takes future usage, energy cost, and reward for delivering balanced power into account. We show that the choice of an EMPC controller is valid as it allows the setpoint to change if certain conditions are met, leading to a more optimal revenue stream from selling flexibility. We find that the economic benefits of participating in delivering balancing power is considerable and offset an increase in energy costs. The increase in energy consumption could be justified as the participation in net stabilisation allows the macro-system to integrate more renewable energy sources. More importantly, the simulations also show that the poorer the energy performance of the water heater, the more flexibility can be sold. From a policy point of view, a minimal energy performance should be determined before allowing participation in net stabilisation.

Abstract: Marine recirculating aquaculture system (MRAS) is an effective technology that provides sustainable farming of food fish globally. However, dissolved organics material (chemical oxygen demand, COD) and especially ammonia are produced from uneaten feed and metabolic wastes of fish. To purify the MRAS water, this study adopted a sequencing biofilm batch reactor (SBBR) and comparatively investigated the performances of four different carriers on ammonia and COD removal. Results indicated that the NH4+-N removal rates were 0.045 +/- 0.05, 0.065 +/- 0.008, 0.089 +/- 0.005, and 0.093 +/- 0.003 kg/(m(3)center dot d), and the COD removal rates were 0.019 +/- 0.010, 0.213 +/- 0.010, 0.255 +/- 0.015, and 0.322 +/- 0.010 kg/(m(3)center dot d) in the SBBRs packed with porous plastic, bamboo ring, maifan stone, and ceramsite carriers, respectively. Among the four carriers, ceramsite exhibited the best performance for both NH4+-N (80%) and COD (33%) removal after the SBBR reached the steady-state operation conditions. For all carriers studied, the NH4+-N removal kinetics could be well simulated by the first-order model, and the NH4+-N and COD removal rates were logarithmically correlated with the carrier's specific surface area. Due to its high ammonia removal, stable performance and easy operation, the ceramsite-packed SBBR is feasible for MRAS water treatment.

Abstract: B substituting O in antiferromagnetic Cr2O3 is known to increase the Ne ' el temperature, whereas the actual B dopant site and the corresponding functionality remains unclear due to the complicated local structure. Herein, A combination of electron energy loss spectroscopy and first-principles calculations were used to unveil B local structures in B doped Cr2O3 thin films. B was found to form either magnetic active BCr4 tetrahedra or various inactive BO3 triangles in the Cr2O3 lattice, with a* and z* bonds exhibiting unique spectral features. Identification of BO3 triangles was achieved by changing the electron momentum transfer to manipulate the differential cross section for the 1s-z* and 1s-a* transitions. Modeling the experimental spectra as a linear combination of simulated B K edges reproduces the experimental z* / a* ratios for 15-42% of the B occupying the active BCr4 structure. This result is further supported by first-principles based thermodynamic calculations.

Abstract: The European Synchrotron Radiation Facility (ESRF) has recently commissioned the new Extremely Brilliant Source (EBS). The gain in brightness as well as the continuous development of beamline instruments boosts the beamline performances, in particular in terms of accelerated data acquisition. This has motivated the development of new access modes as an alternative to standard proposals for access to beamtime, in particular via the “block allocation group” (BAG) mode. Here, we present the recently implemented “historical materials BAG”: a community proposal giving to 10 European institutes the opportunity for guaranteed beamtime at two X-ray powder diffraction (XRPD) beamlines-ID13, for 2D high lateral resolution XRPD mapping, and ID22 for high angular resolution XRPD bulk analyses-with a particular focus on applications to cultural heritage. The capabilities offered by these instruments, the specific hardware and software developments to facilitate and speed-up data acquisition and data processing are detailed, and the first results from this new access are illustrated with recent applications to pigments, paintings, ceramics and wood.

Abstract: Dry deposition velocities have been calculated using three different approaches. Turbulent wind profile theory has been used to predict the drag coefficient, wind speed and friction velocity at 10 m height when the wind speed is measured at a higher altitude. The resulting parameters were introduced in a two-layer deposition model. The second approach was the well-known model of Slinn and Slinn (1980, Atmospheric Environment 14, 1013-1016), whereas the third corresponded to the model published by Williams (1982, Atmospheric Environment 16, 1933 1938). Results point to clear differences. However, in a field experiment carried out at the Southern Bight of the North Sea, all three approaches show relatively comparable results. The role played by the size distribution of atmospheric particulate matter is essential. In our case any of the three models could have given satisfactory outcomes taking into account the wide spread of the experimental results cited in the literature for the same airshed.

Abstract: Synchrotron radiation micro-X-ray fluorescence and micro-X-ray diffraction analysis, micro-computed tomography and transmission electron microscopy were used to investigate the microstructure of turbine blades made of a second generation nickel based superalloy CMSX-4 manufactured by investment casting process via Bridgman technique. The dependence of microstructure on process parameters, among others, on the withdrawal rate was analysed. The results set the stage for optimising the microstructure of the blades in terms of their mechanical properties.

Abstract: For trace analyses of environmental waters, spark-source mass-spectrometry has been combined with a preconcentration procedure involving chelation of the dissolved trace elements with oxine and subsequent adsorption of the oxinates and naturally occurring organic and colloidal metal species onto activated carbon. The activated carbon is filtered off and ashed at low temperature. The residue is dissolved, an internal standard and pure graphite are added and, after drying, the electrodes are prepared. The photographically recorded mass spectrum is evaluated by a suitable computer routine. The error of the procedure is around 30%. While this preconcentration and analysis procedure is capable of measuring about 40 elements quantitatively, in practice 1025 trace elements are determined simultaneously above the 0.1-μg/l. detection limit, as is illustrated by analyses of drinking water, surface and ground water samples. Although a sophisticated technique, SSMS can be considered for regular panoramic survey analyses.

Abstract: Few-electron systems confined in two-dimensional parabolic quantum dots at high magnetic fields are studied by the Hartree-Fock (HF) and exact diagoiialization methods. A generalized multicenter Gaussian basis is proposed in the HF method. A comparison of the HF and exact, results allows as to discuss the relevance of the symmetry of the charge density distribution for the accuracy of the HF method. It is shown that the energy estimates obtained with the broken-symmetry HF wave functions become exact in the infinite magnetic-field limit. In this limit the charge density of the broken-symmetry solution call be identified with the classical charge distribution.

Abstract: An inductively coupled plasma, connected to a sampling cone of a mass spectrometer, is computationally investigated. The effects of the sampler orifice diameter (ranging from 1 to 2 mm) and distance of the sampler cone from the load coil (ranging from 7 to 17 mm) are studied. An increase in sampler orifice diameter leads to a higher central plasma temperature at the place of the sampler, as well as more efficient gas transfer through the sampler, by reducing the interaction of the plasma gas with the sampling cone. However, the flow velocity at the sampler position is found to be independent of the sampler orifice diameter. Moreover, by changing the sampler orifice diameter, we can control whether only the central gas or also the auxiliary gas can exit through the sampler. Finally, with the increasing distance of the sampler from the load coil, the plasma temperature at the place of the sampler decreases slightly, which might also have consequences for the ion generation and transport through the sampling cone.