Home | << 1 2 3 4 5 6 7 8 9 10 11 12 >> |
![]() |
Records | |||||
---|---|---|---|---|---|
Author | Boyat, X.; Ballat-Durand, D.; Marteau, J.; Bouvier, S.; Favergeon, J.; Orekhov, A.; Schryvers, D. | ||||
Title | Interfacial characteristics and cohesion mechanisms of linear friction welded dissimilar titanium alloys: Ti–5Al–2Sn–2Zr–4Mo–4Cr (Ti17) and Ti–6Al–2Sn–4Zr–2Mo (Ti6242) | Type | A1 Journal article | ||
Year | 2019 | Publication | Materials characterization | Abbreviated Journal | Mater Charact |
Volume | 158 | Issue | Pages | 109942 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | A detailed microstructural examination endeavoring to understand the interfacial phenomena yielding to cohesion in solid-state assembling processes was performed. This study focuses on the transition zone of a dissimilar titanium alloy joint obtained by Linear Friction Welding (LFW) the β-metastable Ti17 to the near-α Ti6242. The transition zone delimitating both alloys is characterized by a sharp microstructure change from acicular HCP (Hexagonal Close-Packed) α′ martensitic laths in the Ti6242 to equiaxed BCC β (Body-Centered Cubic) subgrains in the Ti17; these α′ plates were shown to precipitate within prior-β subgrains remarkably more rotated than the ones formed in the Ti17. Both α′ and β microstructures were found to be intermingled within transitional subgrains demarcating a limited gradient from one chemical composition to the other. These peculiar interfacial grains revealed that the cohesive mechanisms between the rubbing surfaces occurred in the single-phase β domain under severe strain and high-temperature conditions. During the hot deformation process, the mutual migration of the crystalline interfaces from one material to another assisted by a continuous dynamic recrystallization process was identified as the main adhesive mechanism at the junction zone. The latter led to successful cohesion between the rubbing surfaces. Once the reciprocating motion stopped, fast cooling caused both materials to experience either a βlean→α′ or βlean→βmetastable transformation in the interfacial zone depending on their local chemical composition. The limited process time and the subsequent hindered chemical homogenization at the transition zone led to retaining the so-called intermingled α’/βm subgrains constituting the border between both Ti-alloys. |
||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000503314000018 | Publication Date | 2019-10-16 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1044-5803 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 2.714 | Times cited | Open Access | ||
Notes | The authors gratefully acknowledge the financial support of the French National Research Agency (ANR) through the OPTIMUM ANR- 14-CE27-0017 project. The authors would also like to thank the Hautsde- France Region and the European Regional Development Fund (ERDF) 2014/2020 for the co-funding of this work. The authors would also like to thank ACB for providing LFW samples as well as Airbus for their technical support. | Approved | Most recent IF: 2.714 | ||
Call Number | EMAT @ emat @c:irua:165084 | Serial ![]() |
5441 | ||
Permanent link to this record | |||||
Author | Sandfeld, S.; Samaee, V.; Idrissi, H.; Groten, J.; Pardoen, T.; Schwaiger, R.; Schryvers, D. | ||||
Title | Datasets for the analysis of dislocations at grain boundaries and during vein formation in cyclically deformed Ni micropillars | Type | A1 Journal article | ||
Year | 2019 | Publication | Data in Brief | Abbreviated Journal | |
Volume | 27 | Issue | 27 | Pages | 104724 |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | The dataset together with the corresponding Python scripts and Jupyter notebooks presented in this article are supplementary data for the work presented in Samaee et al., 2019 [1]. The data itself consists of two parts: the simulation data that was used in [1] to analyze the effect of a particular grain boundary on curved dislocations and the precession electron diffraction (PED) strain maps together with post-processed data for analyzing details of the observed dislocation vein structures. Additionally, the complete stress tensor components, which are not shown in [1], have also been included. The data sets are accompanied by Python code explaining the file formats and showing how to post-process the data. (c) 2019 The Author(s). Published by Elsevier Inc. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/). | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000501988200181 | Publication Date | 2019-11-03 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 2352-3409 | ISBN | Additional Links | UA library record; WoS full record | |
Impact Factor | Times cited | Open Access | |||
Notes | Approved | Most recent IF: NA | |||
Call Number | UA @ admin @ c:irua:165092 | Serial ![]() |
6292 | ||
Permanent link to this record | |||||
Author | Pittarello, L.; Mckibbin, S.; Yamaguchi, A.; Ji, G.; Schryvers, D.; Debaille, V.; Claeys, P. | ||||
Title | Two generations of exsolution lamellae in pyroxene from Asuka 09545 : Clues to the thermal evolution of silicates in mesosiderite | Type | A1 Journal article | ||
Year | 2019 | Publication | The American mineralogist | Abbreviated Journal | Am Mineral |
Volume | 104 | Issue | 11 | Pages | 1663-1672 |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | Mesosiderite meteorites consist of a mixture of crustal basaltic or gabbroic material and metal. Their formation process is still debated due to their unexpected combination of crust and core materials, possibly derived from the same planetesimal parent body, and lacking an intervening mantle component. Mesosiderites have experienced an extremely slow cooling rate from ca. 550 degrees C, as recorded in the metal (0.25-0.5 degrees C/Ma). Here we present a detailed investigation of exsolution features in pyroxene from the Antarctic mesosiderite Asuka (A) 09545. Geothermobarometry calculations, lattice parameters, lamellae orientation, and the presence of clinoenstatite as the host were used in an attempt to constrain the evolution of pyroxene from 1150 to 570 degrees C and the formation of two generations of exsolution lamellae. After pigeonite crystallization at ca. 1150 degrees C, the first exsolution process generated the thick augite lamellae along (100) in the temperature interval 1000-900 degrees C. By further cooling, a second order of exsolution lamellae formed within augite along (001), consisting of monoclinic low-Ca pyroxene, equilibrated in the temperature range 900-800 degrees C. The last process, occurring in the 600-500 degrees C temperature range, was likely the inversion of high to low pigeonite in the host crystal, lacking evidence for nucleation of orthopyroxene. The formation of two generations of exsolution lamellae, as well as of likely metastable pigeonite, suggest non-equilibrium conditions. Cooling was sufficiently slow to allow the formation of the lamellae, their preservation, and the transition from high to low pigeonite. In addition, the preservation of such fine-grained lamellae limits long-lasting, impact reheating to a peak temperature lower than 570 degrees C. These features, including the presence of monoclinic low-Ca pyroxene as the host, are reported in only a few mesosiderites. This suggests a possibly different origin and thermal history from most mesosiderites and that the crystallography (i.e., space group) of low-Ca pyroxene could be used as parameter to distinguish mesosiderite populations based on their cooling history. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000494707400014 | Publication Date | 2019-08-22 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0003-004x | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 2.021 | Times cited | Open Access | ||
Notes | Approved | Most recent IF: 2.021 | |||
Call Number | UA @ admin @ c:irua:164645 | Serial ![]() |
6331 | ||
Permanent link to this record | |||||
Author | Idrissi, H.; Samaee, V.; Lumbeeck, G.; Werf, T.; Pardoen, T.; Schryvers, D.; Cordier, P. | ||||
Title | In Situ Quantitative Tensile Testing of Antigorite in a Transmission Electron Microscope | Type | A1 Journal article | ||
Year | 2020 | Publication | Journal Of Geophysical Research-Solid Earth | Abbreviated Journal | J Geophys Res-Sol Ea |
Volume | 125 | Issue | 3 | Pages | |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | The determination of the mechanical properties of serpentinites is essential toward the understanding of the mechanics of faulting and subduction. Here we present the first in situ tensile tests on antigorite in a transmission electron microscope. A push‐to‐pull deformation device is used to perform quantitative tensile tests, during which force and displacement are measured, while the evolving microstructure is imaged with the microscope. The experiments have been performed at room temperature on 2 × 1 × 0.2 μm3 beams prepared by focused ion beam. The specimens are not single crystals despite their small sizes. Orientation mapping indicated that several grains were well oriented for plastic slip. However, no dislocation activity has been observed even though the engineering tensile stress went up to 700 MPa. We show also that antigorite does not exhibit a purely elastic‐brittle behavior since, despite the presence of defects, the specimens accumulate permanent deformation and did not fail within the elastic regime. Instead, we observe that strain localizes at grain boundaries. All observations concur to show that under these experimental conditions, grain boundary sliding is the dominant deformation mechanism. This study sheds a new light on the mechanical properties of antigorite and calls for further studies on the structure and properties of grain boundaries in antigorite and more generally in phyllosilicates. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000530895800023 | Publication Date | 2020-02-20 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 2169-9313 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.9 | Times cited | Open Access | OpenAccess | |
Notes | We thank S. Guillot for having kindly provided us with the two antigorite samples investigated in this study. We acknowledge funding from the European Research Council (ERC) under the European Union's Horizon 2020 research and innovation program under Grant Agreement 787198—TimeMan. H. Idrissi is mandated by the Belgian National Fund for Scientific Research (FSR‐FNRS). We acknowledge fruitful discussions with A. Baronnet. We thank J. Gasc and an anonymous reviewer for their critical comments. Data (movies of the three in situ deformation experiments) can be downloaded (from https://doi.org/10.5281/zenodo.3583135). | Approved | Most recent IF: 3.9; 2020 IF: 3.35 | ||
Call Number | EMAT @ emat @c:irua:167594 | Serial ![]() |
6355 | ||
Permanent link to this record | |||||
Author | Lumbeeck, G.; Delvaux, A.; Idrissi, H.; Proost, J.; Schryvers, D. | ||||
Title | Analysis of internal stress build-up during deposition of nanocrystalline Ni thin films using transmission electron microscopy | Type | A1 Journal article | ||
Year | 2020 | Publication | Thin solid films : an international journal on the science and technology of thin and thick films | Abbreviated Journal | Thin Solid Films |
Volume | 707 | Issue | Pages | 138076 | |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | Ni thin films sputter-deposited at room temperature with varying Ar pressures were investigated with automated crystal orientation mapping in a transmission electron microscope to uncover the mechanisms controlling the internal stress build-up recorded in-situ during deposition. Large grains were found to induce behaviour similar to a stress-free nucleation layer. The measurements of grain size in most of the Ni thin films are in agreement with the island coalescence model. Low internal stress was observed at low Ar pressure and was explained by the presence of large grains. Relaxation of high internal stress was also noticed at the highest Ar pressure, which was attributed to a decrease of Σ3 twin boundary density due to a low deposition rate. The results provide insightful information to better understand the relationship between structural boundaries and the evolution of internal stress upon deposition of thin films. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000539312200011 | Publication Date | 2020-05-12 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | ||
Impact Factor | Times cited | Open Access | OpenAccess | ||
Notes | This work was supported by the Hercules Foundation [Grant No. AUHA13009], the Flemish Research Fund (FWO) [Grant No. G.0365.15N], and the Flemish Strategic Initiative for Materials (SIM) under the project InterPoCo. Thin film deposition has been realised as part of the WallonHY project, funded by the Public Service of Wallonia – Department of Energy and Sustainable Building. H. Idrissi is mandated by the Belgian National Fund for Scientific Research (FSR-FNRS). | Approved | Most recent IF: NA | ||
Call Number | EMAT @ emat @c:irua:169708 | Serial ![]() |
6370 | ||
Permanent link to this record | |||||
Author | Cautaerts, N.; Lamm, S.; Stergar, E.; Pakarinen, J.; Yang, Y.; Hofer, C.; Schnitzer, R.; Felfer, P.; Verwerft, M.; Delville, R.; Schryvers, D. | ||||
Title | Atom probe tomography data collection from DIN 1.4970 (15-15Ti) austenitic stainless steel irradiated with Fe ions | Type | Dataset | ||
Year | 2020 | Publication | Abbreviated Journal | ||
Volume | Issue | Pages | |||
Keywords | Dataset; Electron microscopy for materials research (EMAT) | ||||
Abstract | This dataset comprises a large collection of atom probe tomography datasets collected from DIN 1.4970 alloy that was irradiated with Fe ions at different conditions. The DIN 1.4970 alloy is an austenitic stainless steel with 15 wt% Cr, 15 wt% Ni, a small addition of Ti. The full composition and characterization of our material can be found published elsewhere [1,2]. Some of our material was subjected to ageing heat treatments at different temperatures for different times. Small samples of our original material and aged material was irradiated at the Michigan Ion Beam Laboratory in 2017 with 4.5 MeV Fe ions up to 40 dpa at an average dose rate of 2×10−4 dpa/s. This was done at three different temperatures: 300, 450, and 600 ºC. Atom probe samples were made of the irradiated layers (approximately 1.5 micron deep) with focused ion beam and mounted on Microtip coupons. APT measurements took place on three CAMECA LEAP-HR systems located at CAES in Idaho Falls, USA (files beginning with R33), at Montanuniversität Leoben in Leoben, Austria (R21) and at Friedrich–Alexander University in Erlangen, Germany (R56). | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | Publication Date | |||
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | ISBN | Additional Links | UA library record | ||
Impact Factor | Times cited | Open Access | Not_Open_Access | ||
Notes | ; ; | Approved | Most recent IF: NA | ||
Call Number | UA @ admin @ c:irua:169127 | Serial ![]() |
6454 | ||
Permanent link to this record | |||||
Author | Penders, A.; Konstantinovic, M.J.; Bosch, R.W.; Schryvers, D. | ||||
Title | Crack initiation in tapered high Si stainless steel specimens : stress threshold analyses | Type | A1 Journal article | ||
Year | 2020 | Publication | Corrosion Engineering Science And Technology | Abbreviated Journal | Corros Eng Sci Techn |
Volume | Issue | Pages | 1-8 | ||
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | Tapered specimens were used for an accelerated test technique to study the crack initiation of high Si stainless steel by means of constant elongation rate tensile testing in a simulated pressurised water reactor environment. Detailed crack density distributions were obtained by applying an advanced crack detection algorithm on iteratively displaced scanning electron microscopy pictures featuring stress corrosion cracks along the specimen's gauge length. By means of finite-element analysis, prominent peaks in the crack density graphs are demonstrated to be related to stress relief and stress build-up during the crack initiation phase. Intrinsic scatter related to the crack detection suggests that stress corrosion cracking is independent of the strain-rate for strain-rates lower than 10(-6 )s(-1). Based on the extrapolation to constant load conditions, the critical threshold value for the duplex high Si stainless steel is estimated to be around 580 MPa. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000549651600001 | Publication Date | 2020-06-30 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1478-422x | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 1.8 | Times cited | 1 | Open Access | Not_Open_Access |
Notes | ; We would like to acknowledge ENGIE Electrabel for the financial support of this work under the contract number BSUEZ5500. ; | Approved | Most recent IF: 1.8; 2020 IF: 0.879 | ||
Call Number | UA @ admin @ c:irua:171292 | Serial ![]() |
6478 | ||
Permanent link to this record | |||||
Author | Pourbabak, S.; Verlinden, B.; Van Humbeeck, J.; Schryvers, D. | ||||
Title | DSC cycling effects on phase transformation temperatures of micron and submicron grain Ni50.8Ti49.2 microwires | Type | A1 Journal article | ||
Year | 2020 | Publication | Shape memory and superelasticity | Abbreviated Journal | |
Volume | Issue | Pages | 1-10 | ||
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | The effect of thermal cycling parameters on the phase transformation temperatures of micron and submicron grain size recrystallized Ni-Ti microwires was investigated. The suppression of martensitic transformation by thermal cycling was found to enhance when combined with room temperature aging between the cycles and enhances even more when aged at elevated temperature of 100 degrees C. While aging at room temperature alone has no clear effect on the martensitic transformation, elevated temperature aging at 100 degrees C alone suppresses the martensitic transformation. All aforementioned effects were found to be stronger in large grain samples than in small grain samples. Martensitic transformation suppression in all cases was in line with the formation of Ni4Ti3 precursors in the form of < 111 & rang;(B2) Ni clusters as concluded from the observed diffuse intensity in the electron diffraction patterns revealing short-range ordering enhancement. Performing thermal cycling in some different temperature ranges to separate the effect of martensitic transformation and high temperature range of DSC cycling revealed that both high temperature- and martensitic transformation-included cycles enhance the short-range ordering. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000530232800001 | Publication Date | 2020-05-04 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 2199-384x; 2199-3858 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | Times cited | 1 | Open Access | Not_Open_Access | |
Notes | ; S.P. would like to thank the Flemish Science Foundation FWO for financial support under Project G.0366.15N. ; | Approved | Most recent IF: NA | ||
Call Number | UA @ admin @ c:irua:169514 | Serial ![]() |
6492 | ||
Permanent link to this record | |||||
Author | Cao, S.; Zeng, C.Y.; Li, Y.Y.; Yao, X.; Ma, X.; Samaee, V.; Schryvers, D.; Zhang, X.P. | ||||
Title | Quantitative FIB/SEM three-dimensional characterization of a unique Ni₄Ti₃ network in a porous Ni50.8Ti49.2 alloy undergoing a two-step martensitic transformation | Type | A1 Journal article | ||
Year | 2020 | Publication | Materials Characterization | Abbreviated Journal | Mater Charact |
Volume | 169 | Issue | Pages | 110595 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | The three-dimensional (3D) nanostructure of Ni4Ti3 precipitates in a porous Ni50.8Ti49.2 alloy has been re-constructed by “Slice-and-View” in a Focused Ion Beam/Scanning Electron Microscope (FIB/SEM). The 3D configuration of these precipitates forming a network structure in the B2 austenite matrix has been characterized via 3D visualization and quantitative analysis including volume fraction, skeleton, degree of anisotropy and local thickness. It is found that dense Ni4Ti3 precipitates occupy 54% of the volume in the B2 austenite matrix. Parallel Ni4Ti3 precipitates grow alongside the surface of a micro-pore, yielding an asymmetric structure, while nano voids do not seem to affect the growth of Ni4Ti3 precipitates. The small average local thickness of the precipitates around 60 nm allows their coherency with the matrix, and further induces the R-phase transformation in the matrix. On the other hand, the B2 matrix exhibits a winding and narrow structure with a skeleton of 18.20 mm and a thickness similar to the precipitates. This discontinuous matrix segmented by the Ni4Ti3 network and pores is responsible for the gradual transformation by stalling the martensite propagation. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000584353100001 | Publication Date | 2020-08-27 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1044-5803 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.7 | Times cited | Open Access | OpenAccess | |
Notes | ; This work was supported by the National Natural Science Foundation of China under Grant Nos. 51401081 and 51571092, the Natural Science Foundation of Guangdong Province through Key Project under Grant No. 2018B0303110012 and General Project under Grant No. 2017A030313323, and China Scholarship Council (CSC). ; | Approved | Most recent IF: 4.7; 2020 IF: 2.714 | ||
Call Number | UA @ admin @ c:irua:173547 | Serial ![]() |
6590 | ||
Permanent link to this record | |||||
Author | Ding, L.; Raskin, J.-P.; Lumbeeck, G.; Schryvers, D.; Idrissi, H. | ||||
Title | TEM investigation of the role of the polycrystalline-silicon film/substrate interface in high quality radio frequency silicon substrates | Type | A1 Journal article | ||
Year | 2020 | Publication | Materials Characterization | Abbreviated Journal | Mater Charact |
Volume | 161 | Issue | Pages | 110174-10 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | The microstructural characteristics of two polycrystalline silicon (poly-Si) films with different electrical properties produced by low-pressure chemical vapour deposition on top of high resistivity silicon substrates were investigated by advanced transmission electron microscopy (TEM), including high resolution aberration corrected TEM and automated crystallographic orientation mapping in TEM. The results reveal that the nature of the poly-Si film/Si substrate interface is the main factor controlling the electrical resistivity of the poly-Si films. The high resistivity and high electrical linearity of poly-Si films are strongly promoted by the Sigma 3 twin type character of the poly-Si/Si substrate interface, leading to the generation of a huge amount of extended defects including stacking faults, Sigma 3 twin boundaries as well as Sigma 9 grain boundaries at this interface. Furthermore, a high density of interfacial dislocations has been observed at numerous common and more exotic grain boundaries deviating from their standard crystallographic planes. In contrast, poly-Si film/Si substrate interfaces with random character do not favour the formation of such complex patterns of defects, leading to poor electrical resistivity of the poly-Si film. This finding opens windows for the development of high resistivity silicon substrates for Radio Frequency (RF) integrated circuits (ICs) applications. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000521515800027 | Publication Date | 2020-01-30 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1044-5803 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.7 | Times cited | Open Access | Not_Open_Access | |
Notes | ; H. Idrissi is mandated by the Belgian National Fund for Scientific Research (FSR-FNRS). ; | Approved | Most recent IF: 4.7; 2020 IF: 2.714 | ||
Call Number | UA @ admin @ c:irua:168664 | Serial ![]() |
6621 | ||
Permanent link to this record | |||||
Author | Cautaerts, N.; Delville, R.; Stergar, E.; Pakarinen, J.; Verwerft, M.; Yang, Y.; Hofer, C.; Schnitzer, R.; Lamm, S.; Felfer, P.; Schryvers, D. | ||||
Title | The role of Ti and TiC nanoprecipitates in radiation resistant austenitic steel: A nanoscale study | Type | A1 Journal article | ||
Year | 2020 | Publication | Acta Materialia | Abbreviated Journal | Acta Mater |
Volume | 197 | Issue | Pages | 184-197 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | This work encompasses an in-depth transmission electron microscopy and atom probe tomography study of Ti-stabilized austenitic steel irradiated with Fe-ions. The focus is on radiation induced segregation and precipitation, and in particular on how Ti and TiC affect these processes. A 15-15Ti steel (grade: DIN 1.4970) in two thermo-mechanical states (cold-worked and aged) was irradiated at different temperatures up to a dose of 40 dpa. At low irradiation temperatures, the cold-worked and aged materials evolved to a similar microstructure dominated by small Si and Ni clusters, corresponding to segregation to small point defect clusters. TiC precipitates, initially present in the aged material, were found to be unstable under these irradiation conditions. Elevated irradiation temperatures resulted in the nucleation of nanometer sized Cr enriched TiC precipitates surrounded by Si and Ni enriched shells. In addition, nanometer sized Ti- and Mn-enriched G-phase (M6Ni16Si7) precipitates formed, often attached to TiC precipitates. Post irradiation, larger number densities of TiC were observed in the cold-worked material compared to the aged material. This was correlated with a lower volume fraction of G-phase. The findings suggest that at elevated irradiation temperatures, the precipitate-matrix interface is an important point defect sink and contributes to the improved radiation resistance of this material. The study is a first of its kind on stabilized steel and demonstrates the significance of the small Ti addition to the evolution of the microstructure under irradiation. (C) 2020 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000564767000001 | Publication Date | 2020-07-10 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1359-6454 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 9.4 | Times cited | Open Access | Not_Open_Access | |
Notes | ; This work was supported by ENGIE [contract number 2015-AC-007 e BSUEZ6900]; the U.S. Department of Energy, Office of Nuclear Energy under DOE Idaho Operations Office Contract DE-AC07051D14517 as part of a Nuclear Science User Facilities experiment; and by the MYRRHA program at SCK-CEN, Belgium. Funding of the Austrian BMK (846933) in the framework of the program “Production of the future” and the “BMK Professorship for Industry” is gratefully acknowledged. We want to thank the staffat MIBL for assisting with the ion irradiations as well as the staffat CAES for assisting with FIB work and conducting APT measurements. ; | Approved | Most recent IF: 9.4; 2020 IF: 5.301 | ||
Call Number | UA @ admin @ c:irua:171956 | Serial ![]() |
6626 | ||
Permanent link to this record | |||||
Author | Pourbabak, S.; Orekhov, A.; Schryvers, D. | ||||
Title | Twin-jet electropolishing for damage-free transmission electron microscopy specimen preparation of metallic microwires | Type | A1 Journal article | ||
Year | 2020 | Publication | Microscopy Research And Technique | Abbreviated Journal | Microsc Res Techniq |
Volume | Issue | Pages | 1-7 | ||
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | A method to prepare TEM specimens from metallic microwires and based on conventional twin-jet electropolishing is introduced. The wire is embedded in an opaque epoxy resin medium and the hardened resin is mechanically polished to reveal the wire on both sides. The resin containing wire is then cut into discs of the appropriate size. The obtained embedded wire is electropolished in a conventional twin-jet electropolishing machine until electron transparency in large areas without radiation damage is achieved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000567944200001 | Publication Date | 2020-09-28 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1059-910x | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 2.5 | Times cited | Open Access | OpenAccess | |
Notes | ; Fonds Wetenschappelijk Onderzoek, Grant/Award Number: G.0366.15N ; | Approved | Most recent IF: 2.5; 2020 IF: 1.147 | ||
Call Number | UA @ admin @ c:irua:171969 | Serial ![]() |
6642 | ||
Permanent link to this record | |||||
Author | Ding, L.; Zhao, L.; Weng, Y.; Schryvers, D.; Liu, Q.; Idrissi, H. | ||||
Title | Atomic-scale investigation of the heterogeneous precipitation in the E (Al₁₈Mg₃Cr₂) dispersoid of 7075 aluminum alloy | Type | A1 Journal article | ||
Year | 2021 | Publication | Journal Of Alloys And Compounds | Abbreviated Journal | J Alloy Compd |
Volume | 851 | Issue | Pages | 156890 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | The heterogeneous precipitation of the eta (MgZn2) phase on the E (Al18Mg3Cr2) dispersoids of the 7075 aluminum alloy was systematically investigated by atomic resolution high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) and energy dispersive X-ray spectrometry (EDX). It is found that coarse B particles are heterogeneously precipitated at the E particle interface after water quenching and isothermal aging at 120 degrees C. The incoherent E/Al interface is responsible for the high tendency of heterogeneous precipitation of the B phase. Two different orientation relationships (ORs) between the eta, E and Al matrix are identified: OR1 [2 (11) over bar0](eta)[011](E)//[(1) over bar 12](Al), (01 (1) over bar0)(eta)//(13 (3) over bar)(E)//(201)(Al), OR2 [(1) over bar 12](E)//[0001](eta)//[011](Al), (01 (1) over bar0 )(eta)//(220)(E)//(34 (4) over bar)(Al). The eta phase is preferential to nucleate along the {111}(E) or the {220}(E) planes, depending on its OR. The heterogeneous nucleation of B phase on the E particle could stabilize the E/Al interface by introducing a coherent E/eta interface, which increases the drive force of heterogeneous precipitation. The reorientation of eta phase and mutual diffusion of solute atoms could assist the coherency of the E/eta interface. The present results suggest that increasing the coherency of the E/Al interface is a promising method to suppress the heterogeneous precipitation of the eta phase. (C) 2020 Elsevier B.V. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000579868900103 | Publication Date | 2020-08-25 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0925-8388 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.133 | Times cited | Open Access | OpenAccess | |
Notes | Approved | Most recent IF: 3.133 | |||
Call Number | UA @ admin @ c:irua:173503 | Serial ![]() |
6717 | ||
Permanent link to this record | |||||
Author | Samaee, V.; Dupraz, M.; Pardoen, T.; VAn Swygenhoven, H.; Schryvers, D.; Idrissi, H. | ||||
Title | Deciphering the interactions between single arm dislocation sources and coherent twin boundary in nickel bi-crystal | Type | A1 Journal article | ||
Year | 2021 | Publication | Nature Communications | Abbreviated Journal | Nat Commun |
Volume | 12 | Issue | 1 | Pages | 962 |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | The introduction of a well-controlled population of coherent twin boundaries (CTBs) is an attractive route to improve the strength ductility product in face centered cubic (FCC) metals. However, the elementary mechanisms controlling the interaction between single arm dislocation sources (SASs), often present in nanotwinned FCC metals, and CTB are still not well understood. Here, quantitative in-situ transmission electron microscopy (TEM) observations of these mechanisms under tensile loading are performed on submicron Ni bi-crystal. We report that the absorption of curved screw dislocations at the CTB leads to the formation of constriction nodes connecting pairs of twinning dislocations at the CTB plane in agreement with large scale 3D atomistic simulations. The coordinated motion of the twinning dislocation pairs due to the presence of the nodes leads to a unique CTB sliding mechanism, which plays an important role in initiating the fracture process at a CTB ledge. TEM observations of the interactions between non-screw dislocations and the CTB highlight the importance of the synergy between the repulsive force of the CTB and the back stress from SASs when the interactions occur in small volumes. Interactions of dislocations with coherent twin boundaries contribute to strength and ductility in metals, but investigating the interaction mechanisms is challenging. Here the authors unravel these mechanisms through quantitative in-situ transmission electron microscopy observations in nickel bi-crystal samples under tensile loading. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000620142700024 | Publication Date | 2021-02-11 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 2041-1723 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 12.124 | Times cited | Open Access | OpenAccess | |
Notes | Approved | Most recent IF: 12.124 | |||
Call Number | UA @ admin @ c:irua:176680 | Serial ![]() |
6722 | ||
Permanent link to this record | |||||
Author | Samae, V.; Cordier, P.; Demouchy, S.; Bollinger, C.; Gasc, J.; Koizumi, S.; Mussi, A.; Schryvers, D.; Idrissi, H. | ||||
Title | Stress-induced amorphization triggers deformation in the lithospheric mantle | Type | A1 Journal article | ||
Year | 2021 | Publication | Nature | Abbreviated Journal | Nature |
Volume | 591 | Issue | 7848 | Pages | 82-86 |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | The mechanical properties of olivine-rich rocks are key to determining the mechanical coupling between Earth's lithosphere and asthenosphere. In crystalline materials, the motion of crystal defects is fundamental to plastic flow(1-4.) However, because the main constituent of olivine-rich rocks does not have enough slip systems, additional deformation mechanisms are needed to satisfy strain conditions. Experimental studies have suggested a non-Newtonian, grain-size-sensitive mechanism in olivine involving grain-boundary sliding(5,6). However, very few microstructural investigations have been conducted on grain-boundary sliding, and there is no consensus on whether a single or multiple physical mechanisms are at play. Most importantly, there are no theoretical frameworks for incorporating the mechanics of grain boundaries in polycrystalline plasticity models. Here we identify a mechanism for deformation at grain boundaries in olivine-rich rocks. We show that, in forsterite, amorphization takes place at grain boundaries under stress and that the onset of ductility of olivine-rich rocks is due to the activation of grain-boundary mobility in these amorphous layers. This mechanism could trigger plastic processes in the deep Earth, where high-stress conditions are encountered (for example, at the brittle-plastic transition). Our proposed mechanism is especially relevant at the lithosphere-asthenosphere boundary, where olivine reaches the glass transition temperature, triggering a decrease in its viscosity and thus promoting grain-boundary sliding. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000626921700014 | Publication Date | 2021-03-03 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0028-0836 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 40.137 | Times cited | Open Access | OpenAccess | |
Notes | Approved | Most recent IF: 40.137 | |||
Call Number | UA @ admin @ c:irua:176656 | Serial ![]() |
6738 | ||
Permanent link to this record | |||||
Author | Ghidelli, M.; Orekhov, A.; Bassi, A.L.; Terraneo, G.; Djemia, P.; Abadias, G.; Nord, M.; Béché, A.; Gauquelin, N.; Verbeeck, J.; Raskin, J.-p.; Schryvers, D.; Pardoen, T.; Idrissi, H. | ||||
Title | Novel class of nanostructured metallic glass films with superior and tunable mechanical properties | Type | A1 Journal article | ||
Year | 2021 | Publication | Acta Materialia | Abbreviated Journal | Acta Mater |
Volume | Issue | Pages | 116955 | ||
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | A novel class of nanostructured Zr50Cu50 (%at.) metallic glass films with superior and tunable mechanical properties is produced by pulsed laser deposition. The process can be controlled to synthetize a wide range of film microstructures including dense fully amorphous, amorphous embedded with nanocrystals and amorphous nano-granular. A unique dense self-assembled nano-laminated atomic arrangement characterized by alternating Cu-rich and Zr/O-rich nanolayers with different local chemical enrichment and amorphous or amorphous-crystalline composite nanostructure has been discovered, while significant in-plane clustering is reported for films synthetized at high deposition pressures. This unique nanoarchitecture is at the basis of superior mechanical properties including large hardness and elastic modulus up to 10 and 140 GPa, respectively and outstanding total elongation to failure (>9%), leading to excellent strength/ductility balance, which can be tuned by playing with the film architecture. These results pave the way to the synthesis of novel class of engineered nanostructured metallic glass films with high structural performances attractive for a number of applications in microelectronics and coating industry. |
||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000670077800004 | Publication Date | 2021-05-12 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1359-6454 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 5.301 | Times cited | 27 | Open Access | OpenAccess |
Notes | H.I. is mandated by the Belgian National Fund for Scientific Research (FSR-FNRS). This work was supported by the Fonds de la Recherche Scientifique – FNRS under Grant T.0178.19 and Grant CDR– J011320F. We acknowledge funding for the direct electron detector used in the 4D stem studies from the Hercules fund 'Direct electron detector for soft matter TEM' from the Flemish Government J.V acknowledges funding from the European Union's Horizon 2020 research and innovation program under grant agreement No 823717 – ESTEEM3. A.O. has received partial funding from the GOA project “Solarpaint” of the University of Antwerp. A.B. and J.V. acknowledge funding through FWO project G093417N ('Compressed sensing enabling low dose imaging in transmission electron microscopy') from the Flanders Research Fund. M.G. and A.L.B acknowledge Chantelle Ekanem for support in PLD depositions. | Approved | Most recent IF: 5.301 | ||
Call Number | EMAT @ emat @c:irua:178142 | Serial ![]() |
6761 | ||
Permanent link to this record | |||||
Author | Akamine, H.; Mitsuhara, M.; Nishida, M.; Samaee, V.; Schryvers, D.; Tsukamoto, G.; Kunieda, T.; Fujii, H. | ||||
Title | Precipitation behaviors in Ti-2.3 Wt Pct Cu alloy during isothermal and two-step aging | Type | A1 Journal article | ||
Year | 2021 | Publication | Metallurgical And Materials Transactions A-Physical Metallurgy And Materials Science | Abbreviated Journal | Metall Mater Trans A |
Volume | 52 | Issue | Pages | 2760-2772 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | Time evolution of precipitates related to age-hardening in Ti-2.3 wt pct Cu alloys was investigated by electron microscopy. In isothermal aging at 723 K, the hardness increases continuously owing to precipitation strengthening, whereas in two-step aging where the aging temperature is switched from 673 K to 873 K after 100 hours, the hardness is found to drastically drop after the aging temperature switches. In isothermal aging, metastable and stable precipitates are independently nucleated, whereas characteristic V-shaped clusters of precipitates are observed during the two-step aging. It is revealed by atomic-scale observations that the V-shaped clusters are composed of metastable and stable precipitates and each type of precipitate has a different orientation relationship with the alpha phase: (10 (3) over bar)//(0001)(alpha) and [0 (1) over bar0]//respectively. The drop in hardness during two-step aging can be explained by a synergistic effect of decreased precipitation strengthening and solid solution strengthening. (C) The Minerals, Metals & Materials Society and ASM International 2021 | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000644823000001 | Publication Date | 2021-04-27 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1073-5623 | ISBN | Additional Links | UA library record; WoS full record | |
Impact Factor | 1.874 | Times cited | Open Access | OpenAccess | |
Notes | Approved | Most recent IF: 1.874 | |||
Call Number | UA @ admin @ c:irua:178222 | Serial ![]() |
6786 | ||
Permanent link to this record | |||||
Author | Van Cauwenbergh, P.; Samaee, V.; Thijs, L.; Nejezchlebova, J.; Sedlak, P.; Ivekovic, A.; Schryvers, D.; Van Hooreweder, B.; Vanmeensel, K. | ||||
Title | Unravelling the multi-scale structure-property relationship of laser powder bed fusion processed and heat-treated AlSi10Mg | Type | A1 Journal article | ||
Year | 2021 | Publication | Scientific Reports | Abbreviated Journal | Sci Rep-Uk |
Volume | 11 | Issue | 1 | Pages | 6423 |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | Tailoring heat treatments for Laser Powder Bed Fusion (LPBF) processed materials is critical to ensure superior and repeatable material properties for high-end applications. This tailoring requires in-depth understanding of the LPBF-processed material. Therefore, the current study aims at unravelling the threefold interrelationship between the process (LPBF and heat treatment), the microstructure at different scales (macro-, meso-, micro-, and nano-scale), and the macroscopic material properties of AlSi10Mg. A similar solidification trajectory applies at different length scales when comparing the solidification of AlSi10Mg, ranging from mould-casting to rapid solidification (LPBF). The similarity in solidification trajectories triggers the reason why the Brody-Flemings cellular microsegregation solidification model could predict the cellular morphology of the LPBF as-printed microstructure. Where rapid solidification occurs at a much finer scale, the LPBF microstructure exhibits a significant grain refinement and a high degree of silicon (Si) supersaturation. This study has identified the grain refinement and Si supersaturation as critical assets of the as-printed microstructure, playing a vital role in achieving superior mechanical and thermal properties during heat treatment. Next, an electrical conductivity model could accurately predict the Si solute concentration in LPBF-processed and heat-treated AlSi10Mg and allows understanding the microstructural evolution during heat treatment. The LPBF-processed and heat-treated AlSi10Mg conditions (as-built (AB), direct-aged (DA), stress-relieved (SR), preheated (PH)) show an interesting range of superior mechanical properties (tensile strength: 300-450 MPa, elongation: 4-13%) compared to the mould-cast T6 reference condition. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000632047000003 | Publication Date | 2021-03-19 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 2045-2322 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 4.259 | Times cited | Open Access | OpenAccess | |
Notes | Approved | Most recent IF: 4.259 | |||
Call Number | UA @ admin @ c:irua:177634 | Serial ![]() |
6791 | ||
Permanent link to this record | |||||
Author | Wang, X.; Yao, X.; Schryvers, D.; Verlinden, B.; Wang, G.; Zhao, G.; Van Humbeeck, J.; Kustov, S. | ||||
Title | Anomalous stress-strain behavior of NiTi shape memory alloy close to the border of superelastic window | Type | A1 Journal article | ||
Year | 2021 | Publication | Scripta Materialia | Abbreviated Journal | Scripta Mater |
Volume | 204 | Issue | Pages | 114135 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | In this work, we report an anomalous phenomenon on superelastic cycling of NiTi shape memory alloys when deforming at the temperature close to the border of superelastic window. New unexpected effects are found-(i) critical stress for inducing martensite transformation during the second loading cycle is higher than that of the first cycle; ( ii ) the plateau stress of the second cycle decreases to the original level when the strain overcomes the limit of the first cycle; ( iii ) transition from good superelasticity in the first cycle to fully irreversible strain in the second. We propose that defects generated during the first superelastic cycle close to the border of superelastic window impede following stress-induced martensitic transformations, leading to the increase of critical stress beyond yield stress of the B2 matrix, and thus functional fatigue of NiTi alloys. (c) 2021 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000690441400007 | Publication Date | 2021-07-14 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1359-6462 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.747 | Times cited | Open Access | OpenAccess | |
Notes | Approved | Most recent IF: 3.747 | |||
Call Number | UA @ admin @ c:irua:181658 | Serial ![]() |
6853 | ||
Permanent link to this record | |||||
Author | Safdel, A.; Zarei-Hanzaki, A.; Abedi, H.R.; Pourbabak, S.; Schryvers, D.; Basu, R. | ||||
Title | Asymmetrical superelastic behavior of thermomechanically processed semi-equiatomic NiTi alloy in tensile and compressive modes of deformation | Type | A1 Journal article | ||
Year | 2021 | Publication | Journal Of Alloys And Compounds | Abbreviated Journal | J Alloy Compd |
Volume | 878 | Issue | Pages | 160443 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | In the present work two different cold working and annealing schemes were utilized, and the asymmetric superelastic response of thermomechanically processed materials were then assessed through cyclic tensile and compressive modes of deformation. The values of transformation stress, transformation strain, and pseudoelastic strain were measured for each treated and solutionized specimens and the asymmetric response was compared. In the solution annealed state, the difference of these parameters at different deformation modes was negligible due to the weak texture of the material, while for thermomechanically treated ones, development of specific deformation and recrystallization texture components was identified to be one of the underlying reasons of intensified asymmetry. The evolved substructure during the thermomechanical processing also played a substantial role in determining the asymmetric response. The presence of fine grains and dense dislocation substructure could hinder the movement of the transformation front, thus limiting the range of transformation. In tensile mode, the transformation stress was lower, but higher transformation strain was achieved, which was discussed relying on the slip activity in specified oriented grains. The lower transformation strain in compression mode led to lower pseudoelastic strain due to the narrow transformation range which finally degraded superelastic response of the material. (C) 2021 Elsevier B.V. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000660477400005 | Publication Date | 2021-05-18 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0925-8388 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.133 | Times cited | Open Access | OpenAccess | |
Notes | Approved | Most recent IF: 3.133 | |||
Call Number | UA @ admin @ c:irua:179564 | Serial ![]() |
6855 | ||
Permanent link to this record | |||||
Author | Marteleur, M.; Idrissi, H.; Amin-Ahmadi, B.; Prima, F.; Schryvers, D.; Jacques, P.J. | ||||
Title | On the nucleation mechanism of {112} < 111 > mechanical twins in as-quenched beta metastable Ti-12 wt.% Mo alloy | Type | A1 Journal article | ||
Year | 2019 | Publication | Materialia | Abbreviated Journal | |
Volume | 7 | Issue | Pages | Unsp 100418 | |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | Recently developed beta-metastable Ti grades take advantage of the simultaneous activation of TRIP and TWIP effects for enhancing their work hardening rate. However, the role of each plasticity mechanism on the macroscopic mechanical response is still unclear. In this work, the nucleation mechanism of the first activated plasticity mechanism, namely {112} < 111 > twinning, was investigated. Firstly, post-mortem TEM analysis showed that twins nucleate on pre-existing microstructural defects such as thermal jogs with the zonal dislocation mechanism. The precipitation of the omega phase on twin boundaries has been observed, as well as the emission of numerous dislocations from super-jogs present in these twin boundaries. It is also shown that {112} < 111 > twins act as effective dislocation sources for the subsequent plasticity mechanisms such as beta -> alpha '' martensitic transformation and {332} < 111 > twinning. Secondly, in situ TEM tensile testing of the investigated Ti grade highlighted the primary role of the initial defect configuration present in the microstructure. It is shown that twins cannot nucleate without the presence of specific defects allowing the triggering of the dislocation decomposition needed for the twinning mechanism highlighted in investigated bulk samples. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000537131000052 | Publication Date | 2019-07-31 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 2589-1529 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | Times cited | Open Access | |||
Notes | Approved | no | |||
Call Number | UA @ admin @ c:irua:170326 | Serial ![]() |
6875 | ||
Permanent link to this record | |||||
Author | Bartholomeeusen, E.; De Cremer, G.; Kennes, K.; Hammond, C.; Hermans, I.; Lu, J.-B.; Schryvers, D.; Jacobs, P.A.; Roeffaers, M.B.J.; Hofkens, J.; Sels, B.F.; Coutino-Gonzalez, E. | ||||
Title | Optical encoding of luminescent carbon nanodots in confined spaces | Type | A1 Journal article | ||
Year | 2021 | Publication | Chemical Communications | Abbreviated Journal | Chem Commun |
Volume | 57 | Issue | 90 | Pages | 11952-11955 |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | Stable emissive carbon nanodots were generated in zeolite crystals using near infrared photon irradiation gradually converting the occluded organic template, originally used to synthesize the zeolite crystals, into discrete luminescent species consisting of nano-sized carbogenic fluorophores, as ascertained using Raman microscopy, and steady-state and time-resolved spectroscopic techniques. Photoactivation in a confocal laser fluorescence microscope allows 3D resolved writing of luminescent carbon nanodot patterns inside zeolites providing a cost-effective and non-toxic alternative to previously reported metal-based nanoclusters confined in zeolites, and opens up opportunities in bio-labelling and sensing applications. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000711122000001 | Publication Date | 2021-10-26 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1359-7345; 1364-548x | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 6.319 | Times cited | Open Access | Not_Open_Access | |
Notes | Approved | Most recent IF: 6.319 | |||
Call Number | UA @ admin @ c:irua:184147 | Serial ![]() |
6876 | ||
Permanent link to this record | |||||
Author | Samaeeaghmiyoni, V.; Cordier, P.; Demouchy, S.; Bollinger, C.; Gasc, J.; Mussi, A.; Schryvers, D.; Idrissi, H. | ||||
Title | Research data supporting for Stress-induced amorphization triggers deformation in the lithospheric mantle | Type | Dataset | ||
Year | 2020 | Publication | Abbreviated Journal | ||
Volume | Issue | Pages | |||
Keywords | Dataset; Electron microscopy for materials research (EMAT) | ||||
Abstract | |||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | Publication Date | |||
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | ISBN | Additional Links | UA library record | ||
Impact Factor | Times cited | Open Access | |||
Notes | Approved | Most recent IF: NA | |||
Call Number | UA @ admin @ c:irua:180668 | Serial ![]() |
6881 | ||
Permanent link to this record | |||||
Author | Yang, M.; Orekhov, A.; Hu, Z.-Y.; Feng, M.; Jin, S.; Sha, G.; Li, K.; Samaee, V.; Song, M.; Du, Y.; Van Tendeloo, G.; Schryvers, D. | ||||
Title | Shearing and rotation of β'' and β' precipitates in an Al-Mg-Si alloy under tensile deformation : in-situ and ex-situ studies | Type | A1 Journal article | ||
Year | 2021 | Publication | Acta Materialia | Abbreviated Journal | Acta Mater |
Volume | 220 | Issue | Pages | 117310 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | The interaction between dislocations and nano-precipitates during deformation directly influences hardening response of precipitation-strengthening metals such as Al-Mg-Si alloys. However, how coherent and semi-coherent nano-precipitates accommodate external deformation applied to an Al alloy remains to be elucidated. In-situ tensile experiments in a transmission electron microscope (TEM) were conducted to study the dynamic process of dislocations cutting through coherent needle-like beta '' precipitates with diameters of 3 similar to 8 nm. Comprehensive investigations using in-situ, ex-situ TEM and atom probe tomography uncovered that beta '' precipitates were firstly sheared into small fragments, and then the rotation of the fragments, via sliding along precipitate/matrix interfaces, destroyed their initially coherent interface with the Al matrix. In contrast, semi-coherent beta' precipitates with sizes similar to beta '' were more difficult to be fragmented and accumulation of dislocations at the interface increased interface misfit between beta' and the Al matrix. Consequently, beta' precipitates could basically maintain their needle-like shape after the tensile deformation. This research gains new insights into the interaction between nano-precipitates and dislocations. (C) 2021 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000705535300005 | Publication Date | 2021-09-12 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1359-6454 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 5.301 | Times cited | Open Access | OpenAccess | |
Notes | Approved | Most recent IF: 5.301 | |||
Call Number | UA @ admin @ c:irua:182528 | Serial ![]() |
6884 | ||
Permanent link to this record | |||||
Author | Idrissi, H.; Samaee, V.; Lumbeeck, G.; van der Werf, T.; Pardoen, T.; Schryvers, D.; Cordier, P. | ||||
Title | Supporting data for “In situ Quantitative Tensile Tests on Antigorite in a Transmission Electron Microscope” | Type | Dataset | ||
Year | 2019 | Publication | Abbreviated Journal | ||
Volume | Issue | Pages | |||
Keywords | Dataset; Electron microscopy for materials research (EMAT) | ||||
Abstract | The determination of the mechanical properties of serpentinites is essential towards the understanding of the mechanics of faulting and subduction. Here, we present the first in situ tensile tests on antigorite in a transmission electron microscope. A push-to-pull deformation device is used to perform quantitative tensile tests, during which force and displacement are measured, while the microstructure is imaged with the microscope. The experiments have been performed at room temperature on beams prepared by focused ion beam. The specimens are not single crystals despite their small sizes. Orientation mapping indicated that some grains were well-oriented for plastic slip. However, no dislocation activity has been observed even though engineering tensile stress went up to 700 MPa. We show also that antigorite does not exhibit an pure elastic-brittle behaviour since, despite the presence of defects, the specimens underwent plastic deformation and did not fail within the elastic regime. Instead, we observe that strain localizes at grain boundaries. All observations concur to show that under our experimental conditions, grain boundary sliding is the dominant deformation mechanism. This study sheds a new light on the mechanical properties of antigorite and calls for further studies on the structure and properties of grain boundaries in antigorite and more generally in phyllosilicates. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | Publication Date | |||
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | ISBN | Additional Links | UA library record | ||
Impact Factor | Times cited | Open Access | |||
Notes | Approved | no | |||
Call Number | UA @ admin @ c:irua:169107 | Serial ![]() |
6891 | ||
Permanent link to this record | |||||
Author | Penders, A.; Konstantinovic, M.J.; Van Renterghem, W.; Bosch, R.W.; Schryvers, D. | ||||
Title | TEM investigation of SCC crack tips in high Si stainless steel tapered specimens | Type | A1 Journal article | ||
Year | 2021 | Publication | Corrosion Engineering Science And Technology | Abbreviated Journal | Corros Eng Sci Techn |
Volume | Issue | Pages | |||
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | The stress corrosion cracking (SCC) mechanism is investigated in high Si duplex stainless steel in a simulated PWR environment based on TEM analysis of FIB-extracted SCC crack tips. The microstructural investigation in the near vicinity of SCC crack tips illustrates a strain-rate dependence in SCC mechanisms. Detailed analysis of the crack tip morphology, that includes crack tip oxidation and surrounding deformation field, indicates the existence of an interplay between corrosion- and deformation-driven failure as a function of the strain rate. Slow strain-rate crack tips exhibit a narrow cleavage failure which can be linked to the film-induced failure mechanism, while rounded shaped crack tips for faster strain rates could be related to the strain-induced failure. As a result, two nominal strain-rate-dependent failure regimes dominated either by corrosion or deformation-driven cracking mechanisms can be distinguished. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000695956400001 | Publication Date | 2021-09-14 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1478-422x | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 0.879 | Times cited | Open Access | OpenAccess | |
Notes | Approved | Most recent IF: 0.879 | |||
Call Number | UA @ admin @ c:irua:181533 | Serial ![]() |
6892 | ||
Permanent link to this record | |||||
Author | Charalampopoulou, E.; Lambrinou, K.; Van der Donck, T.; Paladino, B.; Di Fonzo, F.; Azina, C.; Eklund, P.; Mraz, S.; Schneider, J.M.; Schryvers, D.; Delville, R. | ||||
Title | Early stages of dissolution corrosion in 316L and DIN 1.4970 austenitic stainless steels with and without anticorrosion coatings in static liquid lead-bismuth eutectic (LBE) at 500 degrees C | Type | A1 Journal article | ||
Year | 2021 | Publication | Materials Characterization | Abbreviated Journal | Mater Charact |
Volume | 178 | Issue | Pages | 111234 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | This work addresses the early stages (<= 1000 h) of the dissolution corrosion behavior of 316L and DIN 1.4970 austenitic stainless steels in contact with oxygen-poor (C-O < 10(-8) mass%), static liquid lead-bismuth eutectic (LBE) at 500 degrees C for 600-1000 h. The objective of this study was to determine the relative early-stage resistance of the uncoated steels to dissolution corrosion and to assess the protectiveness of select candidate coatings (Cr2AlC, Al2O3, V2AlxCy). The simultaneous exposure of steels with intended differences in microstructure and thermomechanical state showed the effects of steel grain size, density of annealing/deformation twins, and secondary precipitates on the steel dissolution corrosion behavior. The findings of this study provide recommendations on steel manufacturing with the aim of using the steels to construct Gen-IV lead-cooled fast reactors. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000752582700001 | Publication Date | 2021-06-01 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1044-5803 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 2.714 | Times cited | Open Access | OpenAccess | |
Notes | Approved | Most recent IF: 2.714 | |||
Call Number | UA @ admin @ c:irua:186509 | Serial ![]() |
7061 | ||
Permanent link to this record | |||||
Author | Poulain, R.; Lumbeeck, G.; Hunka, J.; Proost, J.; Savolainen, H.; Idrissi, H.; Schryvers, D.; Gauquelin, N.; Klein, A. | ||||
Title | Electronic and chemical properties of nickel oxide thin films and the intrinsic defects compensation mechanism | Type | A1 Journal article | ||
Year | 2022 | Publication | ACS applied electronic materials | Abbreviated Journal | |
Volume | 4 | Issue | 6 | Pages | 2718-2728 |
Keywords | A1 Journal article; Electron microscopy for materials research (EMAT) | ||||
Abstract | Although largely studied, contradictory results on nickel oxide (NiO) properties can be found in the literature. We herein propose a comprehensive study that aims at leveling contradictions related to NiO materials with a focus on its conductivity, surface properties, and the intrinsic charge defects compensation mechanism with regards to the conditions preparation. The experiments were performed by in situ photo-electron spectroscopy, electron energy loss spectroscopy, and optical as well as electrical measurements on polycrystalline NiO thin films prepared under various preparation conditions by reactive sputtering. The results show that surface and bulk properties were strongly related to the deposition temperature with in particular the observation of Fermi level pinning, high work function, and unstable oxygen-rich grain boundaries for the thin films produced at room temperature but not at high temperature (>200 degrees C). Finally, this study provides substantial information about surface and bulk NiO properties enabling to unveil the origin of the high electrical conductivity of room temperature NiO thin films and also for supporting a general electronic charge compensation mechanism of intrinsic defects according to the deposition temperature. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000819431200001 | Publication Date | 2022-06-07 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 2637-6113 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | Times cited | Open Access | Not_Open_Access | ||
Notes | Approved | Most recent IF: NA | |||
Call Number | UA @ admin @ c:irua:189555 | Serial ![]() |
7081 | ||
Permanent link to this record | |||||
Author | Penders, A.G.; Konstantinovic, M.J.; Yang, T.; Bosch, R.-w.; Schryvers, D.; Somville, F. | ||||
Title | Microstructural investigation of IASCC crack tips extracted from thimble tube O-ring specimens | Type | A1 Journal article | ||
Year | 2022 | Publication | Journal of nuclear materials | Abbreviated Journal | J Nucl Mater |
Volume | 565 | Issue | Pages | 153727-16 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | The microstructural features of intergranular irradiation-assisted stress corrosion crack tips from a redeemed neutron-irradiated flux thimble tube (60 dpa) have been investigated using focused-ion beam analysis and (scanning) transmission electron microscopy. The current work presents a close examination of the deformation field and oxide assembly associated with intergranular cracking, in addition to the analysis of radiation-induced segregation at leading grain boundaries. Evidence of stress induced martensitic transformation extending from the crack tips is presented. Intergranular crack arrest is demonstrated on the account of the external tensile stress orientation, and as a consequence of MnS inclusion particles segregating close to the fractured grain boundary. Exclusive observations of grain boundary oxidation prior to the cracking are presented, which is in full-agreement with the internal oxidation model.(c) 2022 Elsevier B.V. All rights reserved. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000799256300004 | Publication Date | 2022-04-11 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 0022-3115 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 3.1 | Times cited | Open Access | OpenAccess | |
Notes | Approved | Most recent IF: 3.1 | |||
Call Number | UA @ admin @ c:irua:188609 | Serial ![]() |
7086 | ||
Permanent link to this record | |||||
Author | Ding, L.; Sapanathan, T.; Schryvers, D.; Simar, A.; Idrissi, H. | ||||
Title | On the formation of antiphase boundaries in Fe₄Al₁₃ intermetallics during a high temperature treatment | Type | A1 Journal article | ||
Year | 2022 | Publication | Scripta materialia | Abbreviated Journal | Scripta Mater |
Volume | 215 | Issue | Pages | 114726-6 | |
Keywords | A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) | ||||
Abstract | In this paper, we report atomic scale observations and formation mechanisms of a high-density of antiphase boundaries (APBs) within an ultra-fine-grained Fe4Al13 intermetallic layer at an Al/steel interface after a heat treatment at 596 degrees C. The results reveal that the APBs are formed by nucleation and the glide of partial dislocations with Burgers vector of b/3[010] (b = 12.47 angstrom). The intensive activation of APBs locally transforms the Fe4Al13 structure from the quasicrystal approximant structure to a quasicrystal. Very few stacking faults and nanotwins are observed indicating that the formation of planar defects is mainly driven by this transformation. This new insight on the formation of high density of APBs could possibly lead to an improvement in toughness by increasing the strength/ductility balance of this intermetallic. | ||||
Address | |||||
Corporate Author | Thesis | ||||
Publisher | Place of Publication | Editor | |||
Language | Wos | 000800016600003 | Publication Date | 2022-04-08 | |
Series Editor | Series Title | Abbreviated Series Title | |||
Series Volume | Series Issue | Edition | |||
ISSN | 1359-6462 | ISBN | Additional Links | UA library record; WoS full record; WoS citing articles | |
Impact Factor | 6 | Times cited | Open Access | OpenAccess | |
Notes | Approved | Most recent IF: 6 | |||
Call Number | UA @ admin @ c:irua:188644 | Serial ![]() |
7088 | ||
Permanent link to this record |