| Records |
| Author |
De Baere, K.; Verstraelen, H.; Willemen, R.; Smet, J.-P.; Tchuindjang, J.T.; Lecomte-Beckers, J.; Lenaerts, S.; Meskens, R.; Jung, H.G.; Potters, G. |
| Title |
Assessment of corrosion resistance, material properties, and weldability of alloyed steel for ballast tanks |
Type |
A1 Journal article |
| Year |
2017 |
Publication |
Journal of marine science and technology |
Abbreviated Journal |
J Mar Sci Tech-Japan |
| Volume |
22 |
Issue |
1 |
Pages |
176-199 |
Keywords  |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
Ballast tanks are of great importance in the lifetime of modern merchant ships. Making a ballast tank less susceptible to corrosion can, therefore, prolong the useful life of a ship and, thereby, lower its operational cost. An option to reinforce a ballast tank is to construct it out of a corrosion-resistant steel type. Such steel was recently produced by POSCO Ltd., South Korea. After 6 months of permanent immersion, the average corrosion rate of A and AH steel (31 samples) was 535 g m(-2) year(-1), while the Korean CRS was corroding with 378 g m(-2) year(-1). This entails a gain of 29 %. Follow-up measurements after 10, 20, and 24 months confirmed this. The results after 6 months exposure to alternating wet/dry conditions are even more explicit. Furthermore, the physical and metallurgical properties of this steel show a density of 7.646 t/m(3), the elasticity modulus 209.3 GPa, the tensile strength 572 MPa, and the hardness 169HV10. Microscopically, the metal consists of equiaxed and recrystallized grains (ferrite and pearlite), with an average size of between 20 and 30 A mu m (ASTM E 112-12 grain size number between 7 and 8) with a few elongated pearlitic grains. The structure is banded ferrite/pearlite. On the basis of a series of energy dispersive X-ray spectrometer measurements the lower corrosion rate of the steel can be attributed to the interplay of Al, Cr, their oxides, and the corroding steel. In addition, the role of each element in the formation of oxide layers and the mechanisms contributing to the corrosion resistance are discussed. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000395006400015 |
Publication Date |
2016-07-21 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0948-4280 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
0.838 |
Times cited |
3 |
Open Access |
|
| Notes |
; This paper is published with the explicit permission of POSCO Ltd., original source of the corrosion resistant steel. Due to the creativity of the POSCO engineers and scientists, we could have our challenge, presented in this manuscript. The authors wish to thank the BOF funding received from the University of Antwerp and the Maritime Academy. We also wish to express our gratitude towards to the American Bureau of Shipping for their assistance in procuring the CRS plates, their moral and financial support, as well as to OCAS (Arcelor Mittal, Zelzate, Belgium) for their assistance in a number of measurements. ; |
Approved |
Most recent IF: 0.838 |
| Call Number |
UA @ admin @ c:irua:142509 |
Serial |
5928 |
| Permanent link to this record |
| |
|
| |
| Author |
Van Noyen, J.; Middelkoop, V.; Buysse, C.; Kovalevsky, A.; Snijkers, F.; Buekenhoudt, A.; Mullens, S.; Luyten, J.; Kretzschmar, J.; Lenaerts, S. |
| Title |
Fabrication of perovskite capillary membranes for high temperature gas separation |
Type |
A1 Journal article |
| Year |
2012 |
Publication |
Catalysis today |
Abbreviated Journal |
Catal Today |
| Volume |
193 |
Issue |
1 |
Pages |
172-178 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
Oxygen-permeable perovskites with mixed ionic-electronic conducting properties can play an important role in carbon capture and storage techniques. Their ability to separate oxygen from air is needed, more specifically, in oxy-fuel and pre-combustion technologies. In this work, the first detailed comparative analysis and new results are reported on four types of Ba0.5Sr0.5Co0.8Fe0.2O3-delta (BSCF) capillary membranes: non-coated sulphur-containing; catalyst-coated sulphur-containing; non-coated sulphur-free and catalyst-coated sulphur-free. The fabrication of BSCF capillaries by a spinning technique based on phase inversion is further discussed and their oxygen separation performances are interpreted. The comparison of the performance of these different generations of BSCF capillaries of similar dimensions demonstrates a significant impact of the sulphur contamination on both the oxygen flux through the membrane and the activation energy of the overall oxygen transport mechanism. Careful attention is paid to the effect of activation layers on both sulphur-free and sulphur-containing types of capillaries. Additional long-term testing of the sulphur-free BSCF capillaries is presented, where partial decomposition of the membrane surface was observed due to kinetic demixing. (c) 2012 Elsevier B.V. All rights reserved. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000308675900025 |
Publication Date |
2012-04-15 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0920-5861 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
4.636 |
Times cited |
9 |
Open Access |
|
| Notes |
; The authors want to express their thanks to the VITO personnel for their continuous support, especially B. Molenberghs, W. Doyen (Separation and Conversion Technology, VITO), R. Kemps, M. Mertens, I. Thijs, M. Schoeters, W. Bouwen and J. Cooymans (Materials Department, VITO). C. Buysse thankfully acknowledges a Ph.D. scholarship provided by VITO and the University of Antwerp. This work is performed in the framework of the German Helmholtz Alliance Project “MEM-BRAIN”, aiming at the development of gas separation membranes for zero-emission fossil fuel power plants. ; |
Approved |
Most recent IF: 4.636; 2012 IF: 2.980 |
| Call Number |
UA @ admin @ c:irua:101797 |
Serial |
5951 |
| Permanent link to this record |
| |
|
| |
| Author |
Verbruggen, S.W.; Masschaele, K.; Moortgat, E.; Korany, T.E.; Hauchecorne, B.; Martens, J.A.; Lenaerts, S. |
| Title |
Factors driving the activity of commercial titanium dioxide powders towards gas phase photocatalytic oxidation of acetaldehyde |
Type |
A1 Journal article |
| Year |
2012 |
Publication |
Catalysis science & technology |
Abbreviated Journal |
Catal Sci Technol |
| Volume |
2 |
Issue |
11 |
Pages |
2311-2318 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
The photocatalytic activity of two commercial titanium dioxide powders (Cristal Global, Millennium PC500 and Evonik, P25) is compared towards acetaldehyde degradation in the gas phase. In contrast to the extensive literature available, we found a higher activity for the PC500 than for the P25 coating. Here, we present a comprehensive characterization of the bulk and surface properties of both powders. Our comparison shows that the material properties that dominate the overall photocatalytic activity in gas phase differ from those required for the photodegradation of water-borne pollutants. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000310863900020 |
Publication Date |
2012-06-13 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2044-4753; 2044-4761 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
5.773 |
Times cited |
33 |
Open Access |
|
| Notes |
; S.W.V. acknowledges the Research Foundation of Flanders (FWO) for the financial support. J.A.M acknowledges long term funding (Methusalem). ; |
Approved |
Most recent IF: 5.773; 2012 IF: 3.753 |
| Call Number |
UA @ admin @ c:irua:105162 |
Serial |
5952 |
| Permanent link to this record |
| |
|
| |
| Author |
Dong, Y.; Chen, S.-Y.; Lu, Y.; Xiao, Y.-X.; Hu, J.; Wu, S.-M.; Deng, Z.; Tian, G.; Chang, G.-G.; Li, J.; Lenaerts, S.; Janiak, C.; Yang, X.-Y.; Su, B.-L. |
| Title |
Hierarchical MoS2@TiO2 heterojunctions for enhanced photocatalytic performance and electrocatalytic hydrogen evolution |
Type |
A1 Journal article |
| Year |
2018 |
Publication |
Chemistry: an Asian journal |
Abbreviated Journal |
Chem-Asian J |
| Volume |
13 |
Issue |
12 |
Pages |
1609-1615 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
Hierarchical MoS2@TiO2 heterojunctions were synthesized through a one-step hydrothermal method by using protonic titanate nanosheets as the precursor. The TiO2 nanosheets prevent the aggregation of MoS2 and promote the carrier transfer efficiency, and thus enhance the photocatalytic and electrocatalytic activity of the nanostructured MoS2. The obtained MoS2@TiO2 has significantly enhanced photocatalytic activity in the degradation of rhodamineB (over 5.2times compared with pure MoS2) and acetone (over 2.8times compared with pure MoS2). MoS2@TiO2 is also beneficial for electrocatalytic hydrogen evolution (26times compared with pure MoS2, based on the cathodic current density). This work offers a promising way to prevent the self-aggregation of MoS2 and provides a new insight for the design of heterojunctions for materials with lattice mismatches. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000435773300011 |
Publication Date |
2018-04-10 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1861-4728; 1861-471x |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
4.083 |
Times cited |
22 |
Open Access |
|
| Notes |
; This work was supported by the National Key R&D Program of China (2017YFC1103800), PCSIRT (IRT15R52), NSFC (U1662134, U1663225, 51472190, 51611530672, 51503166, 21706199, 21711530705), ISTCP (2015DFE52870), HPNSF (2016CFA033, 2017CFB487), and SKLPPC (PPC2016007). ; |
Approved |
Most recent IF: 4.083 |
| Call Number |
UA @ admin @ c:irua:151971 |
Serial |
5956 |
| Permanent link to this record |
| |
|
| |
| Author |
Caretti, I.; Keulemans, M.; Verbruggen, S.W.; Lenaerts, S.; Van Doorslaer, S. |
| Title |
Light-induced processes in plasmonic Gold/TiO2 photocatalysts studied by electron paramagnetic resonance |
Type |
A1 Journal article |
| Year |
2015 |
Publication |
Topics in catalysis |
Abbreviated Journal |
Top Catal |
| Volume |
58 |
Issue |
12 |
Pages |
776-782 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
X-band and W-band continuous-wave (CW) electron paramagnetic resonance (EPR) was used to study in situ light-induced (LI) mechanisms in commercial P90 titania (90 % anatase/10 % rutile) compared to plasmon-enhanced Au-P90 photocatalyst. These materials were excited using UV and 532 nm visible light to generate different excitation states and distinguish pure charge separation from plasmon-assisted resonance processes. Up to nine different photoinduced species of trapped electrons and holes were identified. LI CW EPR of P90 is presented for the first time, showing a UV excitation response similar to the well-known mixed-phase P25 titania. It is shown that incorporation of Au nanoparticles in Au-P90 and formation of a Schottky junction affects the charge separation state of the catalyst under UV light. Moreover, Au impregnation activated P90 through plasmon hot electron injection under visible light excitation (plasmonic sensitization effect). In general, EPR proved to be crucial to determine the different photoexciation paths and reactions that regulate plasmonic photocatalysis. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000360011200008 |
Publication Date |
2015-08-03 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1022-5528 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
2.486 |
Times cited |
22 |
Open Access |
|
| Notes |
; IC and SVD acknowledge the Research Foundation-Flanders (FWO) for financial support (Grant G.0687.13). SV thanks FWO for financial support through a postdoctoral fellowship and MK acknowledges the agency for Innovation by Science and Technology in Flanders (IWT) for financial support (Ph.D. Grant). ; |
Approved |
Most recent IF: 2.486; 2015 IF: 2.365 |
| Call Number |
UA @ admin @ c:irua:127413 |
Serial |
5968 |
| Permanent link to this record |
| |
|
| |
| Author |
Buysse, C.; Michielsen, B.; Middelkoop, V.; Snijkers, F.; Buekenhondt, A.; Kretzschmar, J.; Lenaerts, S. |
| Title |
Modeling of the performance of BSCF capillary membranes in four-end and three-end integration mode |
Type |
A1 Journal article |
| Year |
2013 |
Publication |
Ceramics international |
Abbreviated Journal |
Ceram Int |
| Volume |
39 |
Issue |
4 |
Pages |
4113-4123 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
Owing to their high surface-to-volume ratio, there has been an increasing research interest in mixed ionic electronic conducting (MIEC) capillary membranes for large-scale high temperature oxygen separation applications. They offer an energy-efficient solution for high temperature combustion processes in oxy-fuel and pre-combustion CO2 capture technologies used in fossil fuel power plants. In order to assess the effectiveness of these membranes in power plant applications, the impact of the geometry of Ba0.5Sr0.5Co0.8Fe0.2O3-delta (BSCF) capillaries on their performance in the three-end and four-end integration modes has been investigated and thoroughly discussed. The model's parameters were derived from four-end mode lab-scale experiments using gas-tight, macrovoid free and sulfur-free BSCF capillary membranes that were prepared by a phase-inversion spinning technique. The results of this modeling study revealed that in the four-end mode higher average oxygen fluxes and smaller total membrane areas can be obtained than in the three-end mode. This is due to the higher pO(2) gradient across the membrane wall. (C) 2012 Elsevier Ltd and Techna Group S.r.l. All rights reserved. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000318129100084 |
Publication Date |
2012-11-09 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0272-8842 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
2.986 |
Times cited |
4 |
Open Access |
|
| Notes |
; The authors wish to thank all the VITO staff involved in the project for their continued support, and in particular B. Molenberghs, W. Doyen, H. Beckers and S. Mullens. C. Buysse would like to acknowledge funding from VITO and the University of Antwerp for a Ph.D. studentship. This work has been performed in the framework of the German Helmholtz Alliance Project “MEM-BRAIN”, aiming at the development of gas separation membranes for zero-emission fossil fuel power plants. ; |
Approved |
Most recent IF: 2.986; 2013 IF: 2.086 |
| Call Number |
UA @ admin @ c:irua:109020 |
Serial |
5971 |
| Permanent link to this record |
| |
|
| |
| Author |
Liao, L.; Heylen, S.; Sree, S.P.; Vallaey, B.; Keulemans, M.; Lenaerts, S.; Roeffaers, M.B.J.; Martens, J.A. |
| Title |
Photocatalysis assisted simultaneous carbon oxidation and NOx reduction |
Type |
A1 Journal article |
| Year |
2017 |
Publication |
Applied catalysis : B : environmental |
Abbreviated Journal |
Appl Catal B-Environ |
| Volume |
202 |
Issue |
|
Pages |
381-387 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
Photocatalysis assisted oxidation of carbon black was performed using TiO2 photocatalyst under UV illumination in an atmosphere with NO, O-2 and water vapor at 150 degrees C. Carbon is oxidized mainly to CO2 while NO is selectively converted to N-2. Enhanced O-2 and NO concentrations have a positive effect on the carbon oxidation rate. At a concentration of 3000 ppm NO and 13.3% O-2 in the gas phase the carbon oxidation rate reaches 2.3 mu g(carbon)/mg(TiO2) h, at a formal electron/photon quantum efficiency of 0.019. HR SEM images reveal uniform gradual reduction of the carbon particle size irrespective of the distance to TiO2 photocatalyst particles in the presence of NO, O-2 and H2O. (C) 2016 Elsevier B.V. All rights reserved. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000388052100038 |
Publication Date |
2016-09-23 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0926-3373 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
9.446 |
Times cited |
11 |
Open Access |
|
| Notes |
; This work was supported by long-term structural funding by the Flemish government (Methusalem). M. Keulemans acknowledges the agency for Innovation by Science and Technology in Flanders (IWT) for financial support (PhD. Grant). M. Roeffaers thanks the ERC for financial support (ERC Starting Grant No. 307523). ; |
Approved |
Most recent IF: 9.446 |
| Call Number |
UA @ admin @ c:irua:139156 |
Serial |
5976 |
| Permanent link to this record |
| |
|
| |
| Author |
Liao, L.; Heylen, S.; Vallaey, B.; Keulemans, M.; Lenaerts, S.; Roeffaers, M.B.J.; Martens, J.A. |
| Title |
Photocatalytic carbon oxidation with nitric oxide |
Type |
A1 Journal article |
| Year |
2015 |
Publication |
Applied catalysis : B : environmental |
Abbreviated Journal |
Appl Catal B-Environ |
| Volume |
166 |
Issue |
|
Pages |
374-380 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
The photocatalytic oxidation of carbon black on TiO2 using nitric oxide as an oxidizing agent was investigated. Layer-wise deposited carbon and TiO2 powder was illuminated with UVA light in the presence of NO at parts per million concentrations in dry and hydrated carrier gas at a temperature of 150 degrees C. Carbon was photocatalytically converted mainly into CO2, and NO mainly into N-2. Carbon oxidation rates of 7.2 mu g/h/mgTiO(2) were achieved in the presence of 3000 ppm NO. Under these experimental conditions in the absence of molecular oxygen, formation of surface nitrates causing TiO2 photocatalyst deactivation is suppressed. Addition of water enhances surface nitrate formation and catalyst deactivation. NO and carbon particulate matter are air pollutants emitted by diesel engines. Elimination of soot collected on a diesel particulate filter through oxidation is a demanding reaction requiring temperatures in excess of 250 degrees C. The present study opens perspectives for a low-temperature regeneration strategy for the diesel particulate filter that simultaneously performs DeNO(x) reactions. (C) 2014 Elsevier B.V. All rights reserved. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000348753400042 |
Publication Date |
2014-12-03 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0926-3373 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
9.446 |
Times cited |
5 |
Open Access |
|
| Notes |
; This work was supported by long-term structural funding by the Flemish government (Methusalem). ; |
Approved |
Most recent IF: 9.446; 2015 IF: 7.435 |
| Call Number |
UA @ admin @ c:irua:123858 |
Serial |
5977 |
| Permanent link to this record |
| |
|
| |
| Author |
Smits, M.; Ling, Y.; Lenaerts, S.; Van Doorslaer, S. |
| Title |
Photocatalytic removal of soot : unravelling of the reaction mechanism by EPR and in situ FTIR spectroscopy |
Type |
A1 Journal article |
| Year |
2012 |
Publication |
ChemPhysChem : a European journal of chemical physics and physical chemistry |
Abbreviated Journal |
Chemphyschem |
| Volume |
13 |
Issue |
18 |
Pages |
4251-4257 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
Photocatalytic soot oxidation is studied on P25 TiO2 as an important model reaction for self-cleaning processes by means of electron paramagnetic resonance (EPR) and Fourier transform infrared (FTIR) spectroscopy. Contacting of carbon black with P25 leads on the one hand to a reduction of the local dioxygen concentration in the powder. On the other hand, the weakly adsorbed radicals on the carbon particles are likely to act as alternative traps for the photogenerated conduction-band electrons. We find furthermore that the presence of dioxygen and oxygen-related radicals is vital for the photocatalytic soot degradation. The complete oxidation of soot to CO2 is evidenced by in situ FTIR spectroscopy, no intermediate CO is detected during the photocatalytic process. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000313692600026 |
Publication Date |
2012-11-13 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1439-4235 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
3.075 |
Times cited |
9 |
Open Access |
|
| Notes |
; This work was supported by the University of Antwerp (PhD grants of M. S. and Y.L.). We would like to thank Birger Hauchecorne for the scientific discussion. ; |
Approved |
Most recent IF: 3.075; 2012 IF: 3.349 |
| Call Number |
UA @ admin @ c:irua:104568 |
Serial |
5980 |
| Permanent link to this record |
| |
|
| |
| Author |
Minjauw, M.M.; Solano, E.; Sree, S.P.; Asapu, R.; Van Daele, M.; Ramachandran, R.K.; Heremans, G.; Verbruggen, S.W.; Lenaerts, S.; Martens, J.A.; Detavernier, C.; Dendooven, J. |
| Title |
Plasma-enhanced atomic layer deposition of silver using Ag(fod)(PEt3) and NH3-plasma |
Type |
A1 Journal article |
| Year |
2017 |
Publication |
Chemistry of materials |
Abbreviated Journal |
Chem Mater |
| Volume |
29 |
Issue |
17 |
Pages |
7114-7121 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
A plasma-enhanced atomic layer deposition (ALD) process using the Ag(fod)(PEt3) precursor [(triethylphosphine)(6,6,7,7,8,8,8-heptafluoro-2,2-dimethy1-3,5-octanedionate)silver(I)] in combination with NH3-plasma is reported. The steady growth rate of the reported process (0.24 +/- 0.03 nm/cycle) was found to be 6 times larger than that of the previously reported Ag ALD process based on the same precursor in combination with H-2-plasma (0.04 +/- 0.02 nm/cycle). The ALD characteristics of the H-2-plasma and NH3-plasma processes were verified. The deposited Ag films were polycrystalline face-centered cubic Ag for both processes. The film morphology was investigated by ex situ scanning electron microscopy and grazing-incidence small-angle X-ray scattering, and it was found that films grown with the NH3-plasma process exhibit a much higher particle areal density and smaller particle sizes on oxide substrates compared to those deposited using the H-2-plasma process. This control over morphology of the deposited Ag is important for applications in catalysis and plasmonics. While films grown with the H-2-plasma process had oxygen impurities (similar to 9 atom %) in the bulk, the main impurity for the NH3-plasma process was nitrogen (similar to 7 atom %). In situ Fourier transform infrared spectroscopy experiments suggest that these nitrogen impurities are derived from NH surface groups generated during the NH3-plasma, which interact with the precursor molecules during the precursor pulse. We propose that the reaction of these surface groups with the precursor leads to additional deposition of Ag atoms during the precursor pulse compared to the H-2-plasma process, which explains the enhanced growth rate of the NH3-plasma process. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000410868600012 |
Publication Date |
2017-08-09 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0897-4756 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
9.466 |
Times cited |
9 |
Open Access |
|
| Notes |
; M.M.M. and J.D. acknowledge the Fonds Wetenschappelijk Onderzoek Vlaanderen (FWO Vlaanderen) for financial support through a personal research grant. We also acknowledge FWO Vlaanderen for providing project funding for this work. We are grateful to the ESRF staff for smoothly running the synchrotron and beamline facilities. We also thank Olivier Janssens for performing the SEM measurements and Stefaan Broekaert for mechanical assistance. J.A.M. acknowledges the Flemish Government for long-term structural funding (Methusalem). ; |
Approved |
Most recent IF: 9.466 |
| Call Number |
UA @ admin @ c:irua:146757 |
Serial |
5983 |
| Permanent link to this record |
| |
|
| |
| Author |
van Walsem, J.; Roegiers, J.; Modde, B.; Lenaerts, S.; Denys, S. |
| Title |
Proof of concept of an upscaled photocatalytic multi-tube reactor : a combined modelling and experimental study |
Type |
A1 Journal article |
| Year |
2019 |
Publication |
Chemical engineering journal |
Abbreviated Journal |
Chem Eng J |
| Volume |
378 |
Issue |
378 |
Pages |
122038 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
Three upscaled multi-tube photocatalytic reactors designed for integration into HVAC (Heating, Ventilation and Air Conditioning) systems were proposed and evaluated using a CFD modelling approach, with emphasis on the flow, irradiation and concentration distribution in the reactor and hence, photocatalytic performance. Based on the obtained insights, the best reactor design was selected, further characterized and improved by an additional proof of concept study and eventually converted into practice. Subsequently, the scaled-up prototype was experimentally tested according to the CEN-EN-16846-1 standard (2017) for volatile organic compound (VOC) removal by an external scientific research center. The combined modelling and experimental approach used in this work, leads to essential insights into the design and assessment of photocatalytic reactors. Therefore, this study provides an essential step towards the optimization and commercialization of photocatalytic reactors for HVAC applications. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000487764800011 |
Publication Date |
2019-06-22 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1385-8947; 1873-3212 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
6.216 |
Times cited |
|
Open Access |
|
| Notes |
; J.V.W. acknowledges the Agentschap Innoveren & Ondernemen for a PhD fellowship. ; |
Approved |
Most recent IF: 6.216 |
| Call Number |
UA @ admin @ c:irua:162190 |
Serial |
5986 |
| Permanent link to this record |
| |
|
| |
| Author |
Huyskens, C.; De Wever, H.; Fovet, Y.; Wegmann, U.; Diels, L.; Lenaerts, S. |
| Title |
Screening of novel MBR fouling reducers : benchmarking with known fouling reducers and evaluation of their mechanism of action |
Type |
A1 Journal article |
| Year |
2012 |
Publication |
Separation and purification technology |
Abbreviated Journal |
Sep Purif Technol |
| Volume |
95 |
Issue |
|
Pages |
49-57 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
A novel fouling characterization method was applied for a first screening of two novel synthetic flocculants developed by BASF (BASF-1 and BASF-2) and benchmarking with six well-known products. Results showed that this MBR-VITO Fouling Measurement (VFM) was able to identify beneficial and adverse effects of different additives on the mixed liquor's reversible and irreversible fouling and, in combination with supporting mixed liquor analyses, allowed to identify the additive's main working mechanism. The first screening tests indicated that BASF-1 and BASF-2 reduced reversible and irreversible fouling to a similar extent as the known synthetic flocculants due to a charge neutralization mechanism, resulting in enhanced flocculation and SMP removal. Further testing at different additive concentrations provided a first indication of the optimal dosage and revealed a considerable risk of overdosing for BASF-2, rendering it less suited for fouling control. In contrast, such adverse effects were not observed for BASF-1. BASF-1 induced similar beneficial effects as the known MPE50 polymer at lower dosage and was therefore considered promising for application in MBRs. (C) 2012 Elsevier B.V. All rights reserved. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000307032100008 |
Publication Date |
2012-04-26 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1383-5866 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
3.359 |
Times cited |
24 |
Open Access |
|
| Notes |
; The authors would like to thank K. Luyckx, J. Fret, L. Heylen, R. Muyshondt, H. Sterckx, J. Verheyden and J. Vande-Velden for technical assistance and V. Iversen for kindly supplying some of the commercial additives. Celine Huyskens is indebted to the Research Foundation-Flanders (FWO). The European Commission is acknowledged for financial support to Aquafit4use (FP7, Grant 211534). ; |
Approved |
Most recent IF: 3.359; 2012 IF: 2.894 |
| Call Number |
UA @ admin @ c:irua:101903 |
Serial |
5990 |
| Permanent link to this record |
| |
|
| |
| Author |
Van Wesenbeeck, K.; Hauchecorne, B.; Lenaerts, S. |
| Title |
Study of positive and negative plasma catalytic oxidation of ethylene |
Type |
A1 Journal article |
| Year |
2017 |
Publication |
Environmental technology |
Abbreviated Journal |
Environ Technol |
| Volume |
38 |
Issue |
12 |
Pages |
1554-1561 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
The effect of introducing a photocatalytically active coating inside a plasma unit is investigated. This technique combines the advantages of high product selectivity from catalysis and the fast start-up from plasma technology. In this study, a preselected TiO2 coating is applied on the collector electrode of a DC corona discharge unit as non-thermal plasma reactor, in order to study the oxidation of ethylene. For both positive and negative polarities an enhanced mineralization is observed while the formation of by-products drastically decreases. The plasma catalytic unit gave the best results when using negative polarity at a voltage of 15kV. This shows the potential of plasma catalysis as indoor air purification technology. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000402018900010 |
Publication Date |
2016-10-03 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0959-3330 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
1.751 |
Times cited |
1 |
Open Access |
|
| Notes |
; The authors wish to thank the University of Antwerp for supporting and funding this research. ; |
Approved |
Most recent IF: 1.751 |
| Call Number |
UA @ admin @ c:irua:144351 |
Serial |
5993 |
| Permanent link to this record |
| |
|
| |
| Author |
Verbruggen, S.W. |
| Title |
TiO2 photocatalysis for the degradation of pollutants in gas phase : from morphological design to plasmonic enhancement |
Type |
A1 Journal article |
| Year |
2015 |
Publication |
Journal of photochemistry and photobiology: C: photochemistry reviews |
Abbreviated Journal |
J Photoch Photobio C |
| Volume |
24 |
Issue |
|
Pages |
64-82 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
TiO2-based photocatalysis has become a viable technology in various application fields such as (waste)water purification, photovoltaics/artificial photosynthesis, environmentally friendly organic synthesis and remediation of air pollution. Because of the increasing impact of bad air quality worldwide, this review focuses on the use and optimization of TiO2-based photocatalysts for gas phase applications. Over the past years various specific aspects of TiO2 photocatalysis have been reviewed individually. The intent of this review is to offer a broad tutorial on (recent) trends in TiO2 photocatalyst modification for the intensification of photocatalytic air treatment. After briefly introducing the fundamentals of photocatalysis, TiO2 photocatalyst modification is discussed both on a morphological and an electronic level from the perspective of gas phase applications. The main focus is laid on recent developments, but also possible opportunities to the field. This review is intended as a solid introduction for researchers new to the field, as well as a summarizing update for established investigators. (C) 2015 Elsevier B.V. All rights reserved. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000360420600004 |
Publication Date |
2015-07-23 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1389-5567 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
12.317 |
Times cited |
121 |
Open Access |
|
| Notes |
; The author wishes to thank the Research Foundation Flanders (FWO) for the financial support and postdoctoral fellowship. ; |
Approved |
Most recent IF: 12.317; 2015 IF: 16.091 |
| Call Number |
UA @ admin @ c:irua:127801 |
Serial |
5997 |
| Permanent link to this record |
| |
|
| |
| Author |
Ouwehand, J.; Van Eynde, E.; De Canck, E.; Lenaerts, S.; Verberckmoes, A.; Van der Voort, P. |
| Title |
Titania-functionalized diatom frustules as photocatalyst for indoor air purification |
Type |
A1 Journal article |
| Year |
2018 |
Publication |
Applied catalysis : B : environmental |
Abbreviated Journal |
Appl Catal B-Environ |
| Volume |
226 |
Issue |
226 |
Pages |
303-310 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
Diatom frustules were extracted from the species Thalassiosira pseudonana and functionalized with titania to be used as photocatalysts in the abatement of acetaldehyde. The synthetic procedure is water-based and environmentally friendly. The synthesis parameters were optimized to give the highest possible photocatalytic activity. The optimized material, visualized with TEM and STEM-EDX, shows the TiO2 nanoparticles grafted inside the frustule pores, as well as on the silica surface. The titania particles, stabilized by the frustules, are 2.5 times more active than the P25 benchmark material. The photocatalyst is then tested in conditions of elevated relative humidity, to simulate indoor air. The catalytic activity only shows a minor decrease at 50% relative humidity, which is a better result than for the P25 benchmark. When tested over an extended period of time, the photocatalyst only shows a minor decrease in activity. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000425476800033 |
Publication Date |
2017-12-26 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0926-3373 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
9.446 |
Times cited |
4 |
Open Access |
|
| Notes |
; The authors are grateful to the Flemish government (VLAIO) for providing funding through grant number 150663. The Thalassiosira Pseudonana algae were kindly provided by TomAlgae. The authors thank Katrien Haustraete, Sander Clerick and Funda Alic for performing TEM and STEM-EDX, SEM and CHN analyses, respectively, and Isabelle Ascoop for fruitful discussions. ; |
Approved |
Most recent IF: 9.446 |
| Call Number |
UA @ admin @ c:irua:149836 |
Serial |
5999 |
| Permanent link to this record |
| |
|
| |
| Author |
Hauchecorne, B.; Tytgat, T.; Terrens, D.; Vanpachtenbeke, F.; Lenaerts, S. |
| Title |
Validation of a newly developed FTIR in situ reactor: real time study of photocatalytic degradation of nitric oxide |
Type |
A1 Journal article |
| Year |
2010 |
Publication |
Infrared physics and technology |
Abbreviated Journal |
Infrared Phys Techn |
| Volume |
53 |
Issue |
6 |
Pages |
469-473 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
For many years, photocatalysis has been proposed as one of the promising techniques to abate environmental pollutants. To improve these reactions it is vital to know the reaction mechanisms of the photocatalytic degradation. This new reactor will make it possible to study the catalytic surface at the moment the reactions occur. By the means of UV LED illumination there is no need of an external UV lamp and thus lowers the cost. The validation of this newly developed reactor is done by investigating the photocatalytic reaction mechanism of nitric oxide (NO) and comparing these findings with those already discussed in literature. From these results, it became clear that the newly developed FTIR in situ reactor allows real time study of photocatalytic degradations. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000285169400009 |
Publication Date |
2010-10-09 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1350-4495 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
1.713 |
Times cited |
12 |
Open Access |
|
| Notes |
; ; |
Approved |
Most recent IF: 1.713; 2010 IF: 0.932 |
| Call Number |
UA @ admin @ c:irua:84561 |
Serial |
6002 |
| Permanent link to this record |
| |
|
| |
| Author |
Van Eynde, E.; Lenaerts, B.; Tytgat, T.; Blust, R.; Lenaerts, S. |
| Title |
Valorization of flue gas by combining photocatalytic gas pretreatment with microalgae production |
Type |
A1 Journal article |
| Year |
2016 |
Publication |
Environmental science and technology |
Abbreviated Journal |
Environ Sci Technol |
| Volume |
50 |
Issue |
5 |
Pages |
2538-2545 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
Utilization of flue gas for algae cultivation seems to be a promising route because flue gas from fossil-fuel combustion processes contains the high amounts of carbon (CO2) and nitrogen (NO) that are required for algae growth. NO is a poor nitrogen source for algae cultivation because of its low reactivity and solubility in water and its toxicity for algae at high concentrations. Here, we present a novel strategy to valorize NO from flue gas as feedstock for algae production by combining a photocatalytic gas pretreatment unit with a microalgal photobioreactor. The photocatalytic air pretreatment transforms NO gas into NO2 gas and thereby enhances the absorption of NO in the cultivation broth. The absorbed NOx will form NO2- and NO3- that can be used as a nitrogen source by algae. The effect of photocatalytic air pretreatment on the growth and biomass productivity of the algae Thalassiosira weissflogii in a semicontinuous system aerated with a model flue gas (1% CO2 and 50 ppm of NO) is investigated during a long-term experiment. The integrated system makes it possible to produce algae with NO from flue gas as the sole nitrogen source and reduces the NOx content in the exhaust gas by 84%. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000371371700048 |
Publication Date |
2016-02-03 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0013-936x; 1520-5851 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
6.198 |
Times cited |
6 |
Open Access |
|
| Notes |
; ; |
Approved |
Most recent IF: 6.198 |
| Call Number |
UA @ admin @ c:irua:132348 |
Serial |
6003 |
| Permanent link to this record |
| |
|
| |
| Author |
Wuyts, W.; Marin, J.; Brusselaers, J.; Vrancken, K. |
| Title |
Circular economy as a COVID-19 cure? |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Resources Conservation And Recycling |
Abbreviated Journal |
Resour Conserv Recy |
| Volume |
162 |
Issue |
|
Pages |
105016-2 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
|
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000569614800012 |
Publication Date |
2020-06-17 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0921-3449 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
13.2 |
Times cited |
3 |
Open Access |
|
| Notes |
; Part of this work was financially supported by the Research Foundation – Flanders (FWO), Belgium and the Ministry of Education, Culture, Sports, Science, and Technology (MEXT), Japan. We want to thank Lynne Stearman Falick and the editor for proofreading and providing comments on previous drafts. ; |
Approved |
Most recent IF: 13.2; 2020 IF: 3.313 |
| Call Number |
UA @ admin @ c:irua:171912 |
Serial |
6469 |
| Permanent link to this record |
| |
|
| |
| Author |
Van De Vijver, E.; Delbecque, N.; Verdoodt, A.; Seuntjens, P. |
| Title |
Estimating the urban soil information gap using exhaustive land cover data: The example of Flanders, Belgium |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Geoderma |
Abbreviated Journal |
Geoderma |
| Volume |
372 |
Issue |
|
Pages |
114371 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
Human activities related to urbanization and industrialization have established a vast territory of urban soil worldwide. On traditional soil maps, urban and industrial areas usually appear as blind spots as they were beyond the interest of national soil survey campaigns. Furthermore, these soil maps are likely already outdated with respect to urban soil due to rapid urban expansion in recent decades. This research aims to evaluate the use of land cover data to estimate the urban soil information gap considering the highly urbanized region of Flanders, Belgium, as a case study. The current extent and spatial distribution of anthropogenic urban soil (1) was estimated through reclassification of recently acquired (2012) exhaustive land cover data, discriminating three qualitative likelihood levels (high-intermediate-low) of anthropogenic influence by urbanization, and (2) compared with its occurrence as represented by the 'Technosols/Not Surveyed area' in the legacy soil map of Belgium, as this map unit best matches with the likelihood for anthropogenic urban soil at the time of the National Soil Survey conducted between end 1940s and mid 1970s. The proposed reclassification of the land cover map resulted in 16.3% and 16.7% of Flanders' total area that corresponds with a high and intermediate likelihood for anthropogenic urban soil, which highlights the underestimation of the anthropogenic urban soil extent as represented by the 'Technosol/Not Surveyed' unit in the legacy soil map (only 13.7%). Moreover, a more realistic spatial pattern of anthropogenic urban soil occurrence was obtained, providing an improved basis for urban soil spatial analysis studies. The produced anthropogenic urban soil likelihood map therefore presents a useful supporting tool for coordinating future soil surveys in urban environments. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000535713600006 |
Publication Date |
2020-04-21 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0016-7061 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
6.1 |
Times cited |
2 |
Open Access |
|
| Notes |
; ; |
Approved |
Most recent IF: 6.1; 2020 IF: 4.036 |
| Call Number |
UA @ admin @ c:irua:170153 |
Serial |
6510 |
| Permanent link to this record |
| |
|
| |
| Author |
Parchomenko, A.; Nelen, D.; Gillabel, J.; Vrancken, K.C.M.; Rechberger, H. |
| Title |
Evaluation of the resource effectiveness of circular economy strategies through multilevel statistical entropy analysis |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Resources Conservation And Recycling |
Abbreviated Journal |
Resour Conserv Recy |
| Volume |
161 |
Issue |
|
Pages |
104925-16 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
In a circular economy (CE), materials, components and products should be kept at the highest level of functionality, while phenomena like dilution, mixing and contamination, often referred to as the loss of resources, should be avoided. One method that can assess the performance of systems to concentrate or avoid dilution of resources is Statistical Entropy Analysis (SEA). Up till now, the method has been applied on the substance level (elements and compounds) only, but showed its applicability to various scales and a variety of systems. Further development of the method allowed to consider information on the product, component and material levels, which makes the method applicable to different combinations of CE strategies, both destructive (e.g. recycling) and non-destructive (e.g. reuse). The method is demonstrated on a simplified vehicle life-cycle, which is modeled through four component groups and six materials. It shows that the method allows to evaluate different CE strategies and identify critical stages which lead to the most severe resource and functionality losses. Based on the methods results, it is possible to determine a perfect circularity reference level, representing a system state that preserves functionality and avoids resource losses. The introduction of a circularity reference level enables the establishment of a framework for resource effectiveness in which diluting and concentrating effects of activities (e.g. sorting) are quantified. The distance of a system to an ideal circular state determines the deviation from a resource-effective system that maintains the original product functionality over a maximum period of time, with minimal efforts. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000569610400032 |
Publication Date |
2020-06-20 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0921-3449 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
13.2 |
Times cited |
|
Open Access |
|
| Notes |
; The authors would like to acknowledge the support of Prof. David Laner for his valuable inputs, as well as the financial support of Vito (Flemish Institute for Technological Research) and Altstoff Recycling Austria AG (ARA). ; |
Approved |
Most recent IF: 13.2; 2020 IF: 3.313 |
| Call Number |
UA @ admin @ c:irua:171925 |
Serial |
6512 |
| Permanent link to this record |
| |
|
| |
| Author |
Koch, K.; Samson, R.; Denys, S. |
| Title |
Experimental and computational aerodynamic characterisation of urban trees |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Biosystems Engineering |
Abbreviated Journal |
Biosyst Eng |
| Volume |
190 |
Issue |
|
Pages |
47-57 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
The Darcy–Forchheimer method is used for modelling the airflow through vegetation. Seven tree and shrub species with contrasting leaf morphologies were installed in a wind tunnel to allow pressure loss measurements across the plant section. Aerodynamic parameters derived from this experiment were inserted into a COMSOL Multiphysics computational fluid dynamics model. The model was confirmed to be a good predictor for airflow through vegetation (R2 = 0.98), regardless of plant morphology. Moreover, supplementing these data with results from a previous study (which considered herbaceous species) revealed a pattern of pressure loss data, that was already been normalised for plant area density. Although we propose further research into kinetic energy transfer in vegetation, this study provides sufficient interesting information for further applications and modelling to describe and predict urban ecology. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000512221700005 |
Publication Date |
2019-12-18 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1537-5110 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
5.1 |
Times cited |
|
Open Access |
|
| Notes |
; This work was supported by the VLAIO-VIS project 'Green building: green walls for sustainable buildings and cities' (140993) and the FWO-SBO project 'EcoCities: Green roofs and walls as a source for ecosystem services in future cities' (S002818N). ; |
Approved |
Most recent IF: 5.1; 2020 IF: 2.044 |
| Call Number |
UA @ admin @ c:irua:164883 |
Serial |
6516 |
| Permanent link to this record |
| |
|
| |
| Author |
Lindeboom, R.E.F.; De Paepe, J.; Vanoppen, M.; Alonso-Fariñas, B.; Coessens, W.; Alloul, A.; Christiaens, M.E.R.; Dotremont, C.; Beckers, H.; Lamaze, B.; Demey, D.; Clauwaert, P.; Verliefde, A.R.D.; Vlaeminck, S.E. |
| Title |
A five-stage treatment train for water recovery from urine and shower water for long-term human Space missions |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Desalination |
Abbreviated Journal |
Desalination |
| Volume |
495 |
Issue |
|
Pages |
114634 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
Long-term human Space missions will rely on regenerative life support as resupply of water, oxygen and food comes with constraints. The International Space Station (ISS) relies on an evaporation/condensation system to recover 74–85% of the water in urine, yet suffers from repetitive scaling and biofouling while employing hazardous chemicals. In this study, an alternative non-sanitary five-stage treatment train for one “astronaut” was integrated through a sophisticated monitoring and control system. This so-called Water Treatment Unit Breadboard (WTUB) successfully treated urine (1.2-L-d−1) with crystallisation, COD-removal, ammonification, nitrification and electrodialysis, before it was mixed with shower water (3.4-L-d−1). Subsequently, ceramic nanofiltration and single-pass flat-sheet RO were used. A four-months proof-of-concept period yielded: (i) chemical water quality meeting the hygienic standards of the European Space Agency, (ii) a 87-±-5% permeate recovery with an estimated theoretical primary energy requirement of 0.2-kWhp-L−1, (iii) reduced scaling potential without anti-scalant addition and (iv) and a significant biological reduction in biofouling potential resulted in stable but biofouling-limited RO permeability of 0.5 L-m−2-h−1-bar−1. Estimated mass breakeven dates and a comparison with the ISS Water Recovery System for a hypothetical Mars transit mission show that WTUB is a promising biological membrane-based alternative to heat-based systems for manned Space missions. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000582172900007 |
Publication Date |
2020-09-15 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0011-9164 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
9.9 |
Times cited |
|
Open Access |
|
| Notes |
|
Approved |
Most recent IF: 9.9; 2020 IF: 5.527 |
| Call Number |
UA @ admin @ c:irua:171514 |
Serial |
6523 |
| Permanent link to this record |
| |
|
| |
| Author |
Li, J.; Zhu, W.; Dong, H.; Yang, Z.; Zhang, P.; Qiang, Z. |
| Title |
Impact of carrier on ammonia and organics removal from zero-discharge marine recirculating aquaculture system with sequencing batch biofilm reactor (SBBR) |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Environmental Science And Pollution Research |
Abbreviated Journal |
Environ Sci Pollut R |
| Volume |
27 |
Issue |
28 |
Pages |
34614-34623 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
Marine recirculating aquaculture system (MRAS) is an effective technology that provides sustainable farming of food fish globally. However, dissolved organics material (chemical oxygen demand, COD) and especially ammonia are produced from uneaten feed and metabolic wastes of fish. To purify the MRAS water, this study adopted a sequencing biofilm batch reactor (SBBR) and comparatively investigated the performances of four different carriers on ammonia and COD removal. Results indicated that the NH4+-N removal rates were 0.045 +/- 0.05, 0.065 +/- 0.008, 0.089 +/- 0.005, and 0.093 +/- 0.003 kg/(m(3)center dot d), and the COD removal rates were 0.019 +/- 0.010, 0.213 +/- 0.010, 0.255 +/- 0.015, and 0.322 +/- 0.010 kg/(m(3)center dot d) in the SBBRs packed with porous plastic, bamboo ring, maifan stone, and ceramsite carriers, respectively. Among the four carriers, ceramsite exhibited the best performance for both NH4+-N (80%) and COD (33%) removal after the SBBR reached the steady-state operation conditions. For all carriers studied, the NH4+-N removal kinetics could be well simulated by the first-order model, and the NH4+-N and COD removal rates were logarithmically correlated with the carrier's specific surface area. Due to its high ammonia removal, stable performance and easy operation, the ceramsite-packed SBBR is feasible for MRAS water treatment. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000565020300005 |
Publication Date |
2019-04-02 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0944-1344; 1614-7499 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
5.8 |
Times cited |
1 |
Open Access |
|
| Notes |
; ; |
Approved |
Most recent IF: 5.8; 2020 IF: 2.741 |
| Call Number |
UA @ admin @ c:irua:171932 |
Serial |
6542 |
| Permanent link to this record |
| |
|
| |
| Author |
Gielis, J.; Caratelli, D.; Shi, P.; Ricci, P.E. |
| Title |
A note on spirals and curvature |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Growth and form |
Abbreviated Journal |
|
| Volume |
1 |
Issue |
1 |
Pages |
1-8 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
Starting from logarithmic, sinusoidal and power spirals, it is shown how these spirals are connected directly with Chebyshev polynomials, Lamé curves, with allometry and Antonelli-metrics in Finsler geometry. Curvature is a crucial concept in geometry both for closed curves and equiangular spirals, and allowed Dillen to give a general definition of spirals. Many natural shapes can be described as a combination of one of two basic shapes in nature—circle and spiral—with Gielis transformations. Using this idea, shape description itself is used to develop a novel approach to anisotropic curvature in nature. Various examples are discussed, including fusion in flowers and its connection to the recently described pseudo-Chebyshev functions. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
|
Publication Date |
2020-02-23 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
|
ISBN |
|
Additional Links |
UA library record |
| Impact Factor |
|
Times cited |
|
Open Access |
|
| Notes |
|
Approved |
Most recent IF: NA |
| Call Number |
UA @ admin @ c:irua:167061 |
Serial |
6569 |
| Permanent link to this record |
| |
|
| |
| Author |
Dattoli, G.; Di Palma, E.; Gielis, J.; Licciardi, S. |
| Title |
Parabolic trigonometry |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
International journal of applied and computational mathematics |
Abbreviated Journal |
|
| Volume |
6 |
Issue |
2 |
Pages |
37 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
|
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
|
Publication Date |
2020-03-04 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2349-5103 |
ISBN |
|
Additional Links |
UA library record |
| Impact Factor |
|
Times cited |
|
Open Access |
|
| Notes |
|
Approved |
Most recent IF: NA |
| Call Number |
UA @ admin @ c:irua:167049 |
Serial |
6578 |
| Permanent link to this record |
| |
|
| |
| Author |
Liu, J.-W.; Wu, S.-M.; Wang, L.-Y.; Tian, G.; Qin, Y.; Wu, J.-X.; Zhao, X.-F.; Zhang, Y.-X.; Chang, G.-G.; Wu, L.; Zhang, Y.-X.; Li, Z.-F.; Guo, C.-Y.; Janiak, C.; Lenaerts, S.; Yang, X.-Y. |
| Title |
Pd/Lewis acid synergy in macroporous Pd@Na-ZSM-5 for enhancing selective conversion of biomass |
Type |
A1 Journal article |
| Year |
2020 |
Publication |
Chemcatchem |
Abbreviated Journal |
Chemcatchem |
| Volume |
|
Issue |
|
Pages |
1-6 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
Pd nanometal particles encapsulated in macroporous Na-ZSM-5 with only Lewis acid sites have been successfully synthesized by a steam-thermal approach. The synergistic effect of Pd and Lewis acid sites have been investigated for significant enhancement of the catalytic selectivity towards furfural alcohol in furfural hydroconversion. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000554645800001 |
Publication Date |
2020-07-11 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1867-3880; 1867-3899 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
4.5 |
Times cited |
1 |
Open Access |
|
| Notes |
; We acknowledge a joint DFG-NSFC project (DFG JA466/39-1, NSFC grant 51861135313). This work was also supported by National Key R&D Program of China (2017YFC1103800), NSFC (U1662134, 21711530705), Jilin Province Science and Technology Development Plan (20180101208JC), HPNSF (2016CFA033), FRFCU (19lgzd16) and ISTCP (2015DFE52870). ; |
Approved |
Most recent IF: 4.5; 2020 IF: 4.803 |
| Call Number |
UA @ admin @ c:irua:171178 |
Serial |
6579 |
| Permanent link to this record |
| |
|
| |
| Author |
Li, Y.; Niklas, K.J.; Gielis, J.; Niinemets, Ü.; Schrader, J.; Wang, R.; Shi, P. |
| Title |
An elliptical blade is not a true ellipse, but a superellipse : evidence from two Michelia species |
Type |
A1 Journal article |
| Year |
2022 |
Publication |
Journal of forestry research |
Abbreviated Journal |
J Forestry Res |
| Volume |
33 |
Issue |
4 |
Pages |
1341-1348 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
The shape of leaf laminae exhibits considerable diversity and complexity that reflects adaptations to environmental factors such as ambient light and precipitation as well as phyletic legacy. Many leaves appear to be elliptical which may represent a ‘default’ developmental condition. However, whether their geometry truly conforms to the ellipse equation (EE), i.e., (x/a)2 + (y/b)2 = 1, remains conjectural. One alternative is described by the superellipse equation (SE), a generalized version of EE, i.e., |x/a|n +|y/b|n = 1. To test the efficacy of EE versus SE to describe leaf geometry, the leaf shapes of two Michelia species (i.e., M. cavaleriei var. platypetala, and M. maudiae), were investigated using 60 leaves from each species. Analysis shows that the majority of leaves (118 out of 120) had adjusted root-mean-square errors of < 0.05 for the nonlinear fitting of SE to leaf geometry, i.e., the mean absolute deviation from the polar point to leaf marginal points was smaller than 5% of the radius of a hypothesized circle with its area equaling leaf area. The estimates of n for the two species were ˂ 2, indicating that all sampled leaves conformed to SE and not to EE. This study confirms the existence of SE in leaves, linking this to its potential functional advantages, particularly the possible influence of leaf shape on hydraulic conductance. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000695118600001 |
Publication Date |
2021-09-12 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1007-662x; 1993-0607 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
3 |
Times cited |
|
Open Access |
OpenAccess |
| Notes |
|
Approved |
Most recent IF: 3 |
| Call Number |
UA @ admin @ c:irua:180967 |
Serial |
7152 |
| Permanent link to this record |
| |
|
| |
| Author |
Li, Y.; Quinn, B.K.; Niinemets, Ü.; Schrader, J.; Gielis, J.; Liu, M.; Shi, P. |
| Title |
Ellipticalness index : a simple measure of the complexity of oval leaf shape |
Type |
A1 Journal article |
| Year |
2022 |
Publication |
Pakistan journal of botany : An official publication of pakistan botanical society |
Abbreviated Journal |
Pak J Bot |
| Volume |
54 |
Issue |
6 |
Pages |
1-8 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
Plants have diverse leaf shapes that have evolved to adapt to the environments they have experienced over their evolutionary history. Leaf shape and leaf size can greatly influence the growth rate, competitive ability, and productivity of plants. However, researchers have long struggled to decide how to properly quantify the complexity of leaf shape. Prior studies recommended the leaf roundness index (RI = 4πA/P2) or dissection index (DI = ), where P is leaf perimeter and A is leaf area. However, these two indices merely measure the extent of the deviation of leaf shape from a circle, which is usually invalid as leaves are seldom circular. In this study, we proposed a simple measure, named the ellipticalness index (EI), for quantifying the complexity of leaf shape based on the hypothesis that the shape of any oval leaf can be regarded as a variation from a standard ellipse. 2220 leaves from nine species of Magnoliaceae were sampled to check the validity of the EI. We also tested the validity of the Montgomery equation (ME), which assumes a proportional relationship between leaf area and the product of leaf length and width, because the EI actually comes from the proportionality coefficient of the ME. We also compared the ME with five other models of leaf area. The ME was found to be the best model for calculating leaf area based on consideration of the trade-off between model fit vs. complexity, which strongly supported the robustness of the EI for describing oval leaf shape. The new index can account for both leaf shape and size, and we conclude that it is a promising method for quantifying and comparing oval leaf shapes across species in future studies. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000814279700028 |
Publication Date |
2022-05-23 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0556-3321 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
1.2 |
Times cited |
|
Open Access |
OpenAccess |
| Notes |
|
Approved |
Most recent IF: 1.2 |
| Call Number |
UA @ admin @ c:irua:188469 |
Serial |
7153 |
| Permanent link to this record |
| |
|
| |
| Author |
Maes, R.R.; Potters, G.; Fransen, E.; Van Schaeren, R.; Lenaerts, S. |
| Title |
Influence of adding low concentration of oxygenates in mineral diesel oil and biodiesel on the concentration of NO, NO₂ and particulate matter in the exhaust gas of a one-cylinder diesel generator |
Type |
A1 Journal article |
| Year |
2022 |
Publication |
International journal of environmental research and public health |
Abbreviated Journal |
|
| Volume |
19 |
Issue |
13 |
Pages |
7637-18 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
Air quality currently poses a major risk to human health worldwide. Transportation is one of the principal contributors to air pollution due to the quality of exhaust gases. For example, the widely used diesel fuel is a significant source of nitrogen oxides (NOx) and particulate matter (PM). To reduce the content NOx and PM, different oxygenated compounds were mixed into a mineral diesel available at the pump, and their effect on the composition of exhaust gas emissions was measured using a one-cylinder diesel generator. In this setup, adding methanol gave the best relative results. The addition of 2000 ppm of methanol decreased the content of NO by 56%, 2000 ppm of isopropanol decreased NO2 by 50%, and 2000 ppm ethanol decreased PM by 63%. An interesting question is whether it is possible to reduce the impact of hazardous components in the exhaust gas even more by adding oxygenates to biodiesels. In this article, alcohol is added to biodiesel in order to establish the impact on PM and NOx concentrations in the exhaust gases. Adding methanol, ethanol, and isopropanol at concentrations of 2000 ppm and 4000 ppm did not improve NOx emissions. The best results were using pure RME for a low NO content, pure diesel for a low NO2 content, and for PM there were no statistically significant differences. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000825645900001 |
Publication Date |
2022-06-23 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1661-7827; 1660-4601 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
|
Times cited |
|
Open Access |
OpenAccess |
| Notes |
|
Approved |
Most recent IF: NA |
| Call Number |
UA @ admin @ c:irua:189476 |
Serial |
7172 |
| Permanent link to this record |
| |
|
| |
| Author |
Ninakanti, R.; Dingenen, F.; Borah, R.; Peeters, H.; Verbruggen, S.W. |
| Title |
Plasmonic hybrid nanostructures in photocatalysis : structures, mechanisms, and applications |
Type |
A1 Journal article |
| Year |
2022 |
Publication |
Topics in Current Chemistry |
Abbreviated Journal |
|
| Volume |
380 |
Issue |
5 |
Pages |
40-62 |
| Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
| Abstract |
(Sun)Light is an abundantly available sustainable source of energy that has been used in catalyzing chemical reactions for several decades now. In particular, studies related to the interaction of light with plasmonic nanostructures have been receiving increased attention. These structures display the unique property of localized surface plasmon resonance, which converts light of a specific wavelength range into hot charge carriers, along with strong local electromagnetic fields, and/or heat, which may all enhance the reaction efficiency in their own way. These unique properties of plasmonic nanoparticles can be conveniently tuned by varying the metal type, size, shape, and dielectric environment, thus prompting a research focus on rationally designed plasmonic hybrid nanostructures. In this review, the term “hybrid” implies nanomaterials that consist of multiple plasmonic or non-plasmonic materials, forming complex configurations in the geometry and/or at the atomic level. We discuss the synthetic techniques and evolution of such hybrid plasmonic nanostructures giving rise to a wide variety of material and geometric configurations. Bimetallic alloys, which result in a new set of opto-physical parameters, are compared with core–shell configurations. For the latter, the use of metal, semiconductor, and polymer shells is reviewed. Also, more complex structures such as Janus and antenna reactor composites are discussed. This review further summarizes the studies exploiting plasmonic hybrids to elucidate the plasmonic-photocatalytic mechanism. Finally, we review the implementation of these plasmonic hybrids in different photocatalytic application domains such as H2 generation, CO2 reduction, water purification, air purification, and disinfection. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Wos |
000839670500009 |
Publication Date |
2022-08-11 |
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
2364-8961 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
| Impact Factor |
|
Times cited |
|
Open Access |
OpenAccess |
| Notes |
|
Approved |
Most recent IF: NA |
| Call Number |
UA @ admin @ c:irua:189825 |
Serial |
7195 |
| Permanent link to this record |
