|
“Study of positive and negative plasma catalytic oxidation of ethylene”. Van Wesenbeeck K, Hauchecorne B, Lenaerts S, Environmental technology 38, 1554 (2017). http://doi.org/10.1080/09593330.2016.1237553
Abstract: The effect of introducing a photocatalytically active coating inside a plasma unit is investigated. This technique combines the advantages of high product selectivity from catalysis and the fast start-up from plasma technology. In this study, a preselected TiO2 coating is applied on the collector electrode of a DC corona discharge unit as non-thermal plasma reactor, in order to study the oxidation of ethylene. For both positive and negative polarities an enhanced mineralization is observed while the formation of by-products drastically decreases. The plasma catalytic unit gave the best results when using negative polarity at a voltage of 15kV. This shows the potential of plasma catalysis as indoor air purification technology.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 1.751
Times cited: 1
DOI: 10.1080/09593330.2016.1237553
|
|
|
“Titania-functionalized diatom frustules as photocatalyst for indoor air purification”. Ouwehand J, Van Eynde E, De Canck E, Lenaerts S, Verberckmoes A, Van der Voort P, Applied catalysis : B : environmental 226, 303 (2018). http://doi.org/10.1016/J.APCATB.2017.12.063
Abstract: Diatom frustules were extracted from the species Thalassiosira pseudonana and functionalized with titania to be used as photocatalysts in the abatement of acetaldehyde. The synthetic procedure is water-based and environmentally friendly. The synthesis parameters were optimized to give the highest possible photocatalytic activity. The optimized material, visualized with TEM and STEM-EDX, shows the TiO2 nanoparticles grafted inside the frustule pores, as well as on the silica surface. The titania particles, stabilized by the frustules, are 2.5 times more active than the P25 benchmark material. The photocatalyst is then tested in conditions of elevated relative humidity, to simulate indoor air. The catalytic activity only shows a minor decrease at 50% relative humidity, which is a better result than for the P25 benchmark. When tested over an extended period of time, the photocatalyst only shows a minor decrease in activity.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 9.446
Times cited: 4
DOI: 10.1016/J.APCATB.2017.12.063
|
|
|
“Validation of a newly developed FTIR in situ reactor: real time study of photocatalytic degradation of nitric oxide”. Hauchecorne B, Tytgat T, Terrens D, Vanpachtenbeke F, Lenaerts S, Infrared physics and technology 53, 469 (2010). http://doi.org/10.1016/J.INFRARED.2010.09.008
Abstract: For many years, photocatalysis has been proposed as one of the promising techniques to abate environmental pollutants. To improve these reactions it is vital to know the reaction mechanisms of the photocatalytic degradation. This new reactor will make it possible to study the catalytic surface at the moment the reactions occur. By the means of UV LED illumination there is no need of an external UV lamp and thus lowers the cost. The validation of this newly developed reactor is done by investigating the photocatalytic reaction mechanism of nitric oxide (NO) and comparing these findings with those already discussed in literature. From these results, it became clear that the newly developed FTIR in situ reactor allows real time study of photocatalytic degradations.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 1.713
Times cited: 12
DOI: 10.1016/J.INFRARED.2010.09.008
|
|
|
“Valorization of flue gas by combining photocatalytic gas pretreatment with microalgae production”. Van Eynde E, Lenaerts B, Tytgat T, Blust R, Lenaerts S, Environmental science and technology 50, 2538 (2016). http://doi.org/10.1021/ACS.EST.5B04824
Abstract: Utilization of flue gas for algae cultivation seems to be a promising route because flue gas from fossil-fuel combustion processes contains the high amounts of carbon (CO2) and nitrogen (NO) that are required for algae growth. NO is a poor nitrogen source for algae cultivation because of its low reactivity and solubility in water and its toxicity for algae at high concentrations. Here, we present a novel strategy to valorize NO from flue gas as feedstock for algae production by combining a photocatalytic gas pretreatment unit with a microalgal photobioreactor. The photocatalytic air pretreatment transforms NO gas into NO2 gas and thereby enhances the absorption of NO in the cultivation broth. The absorbed NOx will form NO2- and NO3- that can be used as a nitrogen source by algae. The effect of photocatalytic air pretreatment on the growth and biomass productivity of the algae Thalassiosira weissflogii in a semicontinuous system aerated with a model flue gas (1% CO2 and 50 ppm of NO) is investigated during a long-term experiment. The integrated system makes it possible to produce algae with NO from flue gas as the sole nitrogen source and reduces the NOx content in the exhaust gas by 84%.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 6.198
Times cited: 6
DOI: 10.1021/ACS.EST.5B04824
|
|
|
“Pd/Lewis acid synergy in macroporous Pd@Na-ZSM-5 for enhancing selective conversion of biomass”. Liu J-W, Wu S-M, Wang L-Y, Tian G, Qin Y, Wu J-X, Zhao X-F, Zhang Y-X, Chang G-G, Wu L, Zhang Y-X, Li Z-F, Guo C-Y, Janiak C, Lenaerts S, Yang X-Y, Chemcatchem , 1 (2020). http://doi.org/10.1002/CCTC.202000868
Abstract: Pd nanometal particles encapsulated in macroporous Na-ZSM-5 with only Lewis acid sites have been successfully synthesized by a steam-thermal approach. The synergistic effect of Pd and Lewis acid sites have been investigated for significant enhancement of the catalytic selectivity towards furfural alcohol in furfural hydroconversion.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 4.5
Times cited: 1
DOI: 10.1002/CCTC.202000868
|
|
|
“Influence of adding low concentration of oxygenates in mineral diesel oil and biodiesel on the concentration of NO, NO₂, and particulate matter in the exhaust gas of a one-cylinder diesel generator”. Maes RR, Potters G, Fransen E, Van Schaeren R, Lenaerts S, International journal of environmental research and public health 19, 7637 (2022). http://doi.org/10.3390/IJERPH19137637
Abstract: Air quality currently poses a major risk to human health worldwide. Transportation is one of the principal contributors to air pollution due to the quality of exhaust gases. For example, the widely used diesel fuel is a significant source of nitrogen oxides (NOx) and particulate matter (PM). To reduce the content NOx and PM, different oxygenated compounds were mixed into a mineral diesel available at the pump, and their effect on the composition of exhaust gas emissions was measured using a one-cylinder diesel generator. In this setup, adding methanol gave the best relative results. The addition of 2000 ppm of methanol decreased the content of NO by 56%, 2000 ppm of isopropanol decreased NO2 by 50%, and 2000 ppm ethanol decreased PM by 63%. An interesting question is whether it is possible to reduce the impact of hazardous components in the exhaust gas even more by adding oxygenates to biodiesels. In this article, alcohol is added to biodiesel in order to establish the impact on PM and NOx concentrations in the exhaust gases. Adding methanol, ethanol, and isopropanol at concentrations of 2000 ppm and 4000 ppm did not improve NOx emissions. The best results were using pure RME for a low NO content, pure diesel for a low NO2 content, and for PM there were no statistically significant differences.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.3390/IJERPH19137637
|
|
|
“Stoichiometry design in hierarchical CoNiFe phosphide for highly efficient water oxidation”. Chen J, Ying J, Xiao Y, Dong Y, Ozoemena K I, Lenaerts S, Yang X, Science China : materials 65, 2685 (2022). http://doi.org/10.1007/S40843-022-2061-X
Abstract: Rational composition design of trimetallic phosphide catalysts is of significant importance for enhanced surface reaction and efficient catalytic performance. Herein, hierarchical CoxNiyFezP with precise control of stoichiometric metallic elements (x:y:z = (1-10):(1-10):1) has been synthesized, and Co1.3Ni0.5Fe0.2P, as the most optimal composition, exhibits remarkable catalytic activity (eta = 320 mV at 10 mA cm(-2)) and long-term stability (ignorable decrease after 10 h continuous test at the current density of 10 mA cm(-2)) toward oxygen evolution reaction (OER). It is found that the surface P in Co1.3Ni0.5Fe0.2P was replaced by 0 under the OER process. The density function theory calculations before and after long-term stability tests suggest the clear increasing of the density of states near the Fermi level of Co1.3Ni0.5Fe0.2P/ Co1.3Ni0.5Fe0.2O, which could enhance the OH- adsorption of our electrocatalysts and the corresponding OER performance.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 8.1
DOI: 10.1007/S40843-022-2061-X
|
|
|
“A core-shell confined Pd@TS-1 @meso-SiO2 catalyst and its synergy effect on styrene oxidation”. Wang Y-T, Wu S-M, Luo G-Q, Tian G, Wang L-Y, Xiao S-T, Wu J-X, Wu A, Wu K-J, Lenaerts S, Yang X-Y, Applied catalysis : A : general 650, 119016 (2023). http://doi.org/10.1016/J.APCATA.2022.119016
Abstract: Dual active sites from acidic zeolite and Pd are not only capable of catalyzing multiple type of reactions, but could also generate unique functions owing to the synergy between metals and acidic sites. However, there are only a few reports on the investigation of the synergy of acid/Pd dual sites in TS-1. Herein, TS-1 confined Pd catalyst with mesoporous silica shell (Pd@TS-1 @meso-SiO2) has been successfully synthesized and its synergy effect contributes to the enhanced conversion rate (19.2%) and selectivity (74.7%) on styrene oxidation. The interaction between Pd and TS-1 has been investigated by EPR and 1H NMR techniques, the experimental measurements show an obvious change in the signal distribution of weakly acidic terminal hydroxyls and hydrogen-bonding silanols. The schematic illustration of selective styrene oxidation in the model of Pd@TS-1 @meso-SiO2 is proposed to clarify the synergistic effect on styrene oxidation between TS-1 and Pd nanoparticles at an atomic-/nanoscale.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 5.5
DOI: 10.1016/J.APCATA.2022.119016
|
|
|
“In situ study of ballast tank corrosion on ships: part 1”. Verstraelen H, de Baere K, Schillemans W, Lemmens L, Dewil R, Lenaerts S, Potters G, Materials performance 48, 48 (2009)
Keywords: A1 Journal article; Engineering sciences. Technology; Theory of quantum systems and complex systems; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 0.149
|
|
|
“In situ study of ballast tank corrosion on ships: part 2”. Verstraelen H, de Baere K, Schillemans W, Lemmens L, Dewil R, Lenaerts S, Potters G, Materials performance 48, 54 (2009)
Abstract: A study was undertaken to determine causes and effects of corrosion processes in ballast tanks. Part 1 of this article (October 2009 MP) described the data collection. Part 2 describes the development of a corrosion index (CI) derived from the general International Association of Classification Societies corrosion assessment methods. The CI can be used in situ to assess ballast tank corrosion. An average timeline for-corrosion of tanks is presented.
Keywords: A1 Journal article; Engineering sciences. Technology; Theory of quantum systems and complex systems; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 0.149
|
|
|
“Can we find an optimal fatty acid composition of biodiesel in order to improve oxidation stability?”.Maes RR, Potters G, Fransen E, Geuens J, Van Schaeren R, Lenaerts S, Sustainability 15, 10310 (2023). http://doi.org/10.3390/SU151310310
Abstract: Air quality currently poses a major risk for human health. Currently, diesel is widely used as fuel and is a significant source of nitrogen oxides (NOx) and particulate matter (PM), both hazardous to human health. A good alternative for mineral diesel is biodiesel, not only for the improvement of hazardous components in the exhaust gases but also because it can be produced in view of a circular economy. Biodiesel consists of a mix of different fatty acid methyl esters, which can react with oxygen. As a consequence, the oxidation stability of biodiesel has to be studied, because the oxidation of biodiesel could affect the performance of the engine due to the wear of injectors and fuel pumps. The oxidation stability could also affect the quality of the exhaust gases due to increases in NOx and PM. The basic question we try to answer in this communication is: 'Can we find an optimal fatty acid composition in order to have a maximal oxidation stability?' In this article, we try to find the optimal fatty acid composition according to the five most common fatty acid methyl esters present in biodiesel in order to reach a maximal oxidation stability. The measurements and statistical analysis show, however, that there is no useful regression model because there are statistically significant two- and three-way interactions among the different fatty acids.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL); Medical Genetics (MEDGEN)
Impact Factor: 3.9
DOI: 10.3390/SU151310310
|
|
|
“Tuning the turnover frequency and selectivity of photocatalytic CO2 reduction to CO and methane using platinum and palladium nanoparticles on Ti-Beta zeolites”. Blommaerts N, Hoeven N, Arenas Esteban D, Campos R, Mertens M, Borah R, Glisenti A, De Wael K, Bals S, Lenaerts S, Verbruggen SW, Cool P, Chemical Engineering Journal 410, 128234 (2021). http://doi.org/10.1016/j.cej.2020.128234
Abstract: A Ti-Beta zeolite was used in gas phase photocatalytic CO2 reduction to reduce the charge recombination rate and increase the surface area compared to P25 as commercial benchmark, reaching 607 m2 g-1. By adding Pt nanoparticles, the selectivity can be tuned toward CO, reaching a value of 92% and a turnover frequency (TOF) of 96 µmol.gcat-1.h-1, nearly an order of magnitude higher in comparison with P25. By adding Pd nanoparticles the selectivity can be shifted from CO (70% for a bare Ti-Beta zeolite), toward CH4 as the prevalent species (60%). In this way, the selectivity toward CO or CH4 can be tuned by either using Pt or Pd. The TOF values obtained in this work outperform reported state-of-the-art values in similar research. The improved activity by adding the nanoparticles was attributed to an improved charge separation efficiency, together with a plasmonic contribution of the metal nanoparticles under the applied experimental conditions.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL); Electron microscopy for materials research (EMAT); Laboratory of adsorption and catalysis (LADCA); AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Impact Factor: 6.216
Times cited: 15
DOI: 10.1016/j.cej.2020.128234
|
|
|
“Monitoring the laccase reaction of vanillin and poplar hydrolysate”. Sóti V, Jacquet N, Apers S, Richel A, Lenaerts S, Cornet I, Journal of chemical technology and biotechnology 91, 1914 (2016). http://doi.org/10.1002/JCTB.4789
Abstract: BACKGROUND Laccase is an intensively researched enzyme for industrial use. Except for decolorisation measurements, HPLC analysis is the conventional method for monitoring the phenolic removal during laccase enzyme reaction. This paper reports an investigation of the continuous UV absorbance follow-up of the laccase reaction with steam pretreated poplar hydrolysate. RESULTS Vanillin was used as a model substrate and lignocellulose xylose rich fraction (XRF) as a biologically complex substrate for laccase detoxification. The reaction was followed by HPLC-UV as well as by UV spectrometric measurements. Results suggest that the reaction can be successfully monitored by measuring the change of UV absorbance at 280 nm, without previous compound separation. In case of XRF experiments the spectrophotometric follow-up is especially useful, as HPLC analysis takes a long time and provides less information than in case of single substrates. The method seems to be suitable for optimization and process control. CONCLUSION The obtained results can help to construct a fast, easy and straightforward monitoring system for laccase-phenolic substrate reactions.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL); Biochemical Wastewater Valorization & Engineering (BioWaVE)
Impact Factor: 3.135
Times cited: 3
DOI: 10.1002/JCTB.4789
|
|
|
“Of enzyme use in cost-effective high solid simultaneous saccharification and fermentation processes”. Sóti V, Lenaerts S, Cornet I, Journal of biotechnology 270, 70 (2018). http://doi.org/10.1016/J.JBIOTEC.2018.01.020
Abstract: Enzyme cost is considered to be one of the most significant factors defining the final product price in lignocellulose hydrolysis and fermentation. Enzyme immobilization and recycling can be a tool to decrease costs. However, high solid loading is a key factor towards high product titers, and recovery of immobilized enzymes from this thick liquid is often overlooked. This paper aims to evaluate the economic feasibility of immobilized enzymes in simultaneous saccharification and fermentation (SSF) of lignocellulose biomass in general, as well as the recuperation of magnetic immobilized enzymes (m-CLEAs) during high solid loading in simultaneous saccharification, detoxification and fermentation processes (SSDF) of lignocellulose biomass. Enzyme prices were obtained from general cost estimations by Klein-Marcuschamer et al. [Klein-Marcuschamer et al. (2012) Biotechnol. Bioeng. 109, 10831087]. During enzyme cost analysis, the influence of inoculum recirculation as well as a shortened fermentation time was explored. Both resulted in 15% decrease of final enzyme product price. Enzyme recuperation was investigated experimentally and 99.5 m/m% of m-CLEAs was recovered from liquid medium in one step, while 88 m/m% could still be recycled from a thick liquid with high solid concentrations (SSF fermentation broth). A mathematical model was constructed to calculate the cost of immobilized and free enzyme utilization and showed that, with current process efficiencies and commercial enzyme prices, the cost reduction obtained by enzyme immobilization can reach around 60% compared to free enzyme utilization, while lower enzyme prices will result in a lower percentage of immobilization related savings, but overall enzyme costs will decrease significantly. These results are applied in a case study, estimating the viability of shifting from sugar to lignocellulose substrate for a 100 t lactic acid fermentation batch. It was concluded that it will only be economically feasible if the enzymes are produced at the most optimistic variable cost and either the activity of the immobilized catalyst or the recovery efficiency is further increased.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL); Biochemical Wastewater Valorization & Engineering (BioWaVE)
Impact Factor: 2.599
Times cited: 6
DOI: 10.1016/J.JBIOTEC.2018.01.020
|
|
|
“Plasmonic Near-Field Localization of Silver Core–Shell Nanoparticle Assemblies via Wet Chemistry Nanogap Engineering”. Asapu R, Ciocarlan R-G, Claes N, Blommaerts N, Minjauw M, Ahmad T, Dendooven J, Cool P, Bals S, Denys S, Detavernier C, Lenaerts S, Verbruggen SW, ACS applied materials and interfaces 9, 41577 (2017). http://doi.org/10.1021/acsami.7b13965
Abstract: Silver nanoparticles are widely used in the field of plasmonics because of their unique optical properties. The wavelength-dependent surface plasmon resonance gives rise to a strongly enhanced electromagnetic field, especially at so-called hot spots located in the nanogap in-between metal nanoparticle assemblies. Therefore, the interparticle distance is a decisive factor in plasmonic applications, such as surface-enhanced Raman spectroscopy (SERS). In this study, the aim is to engineer this interparticle distance for silver nanospheres using a convenient wet-chemical approach and to predict and quantify the corresponding enhancement factor using both theoretical and experimental tools. This was done by building a tunable ultrathin polymer shell around the nanoparticles using the layer-by-layer method, in which the polymer shell acts as the separating interparticle spacer layer. Comparison of different theoretical approaches and corroborating the results with SERS analytical experiments using silver and silver−polymer core−shell nanoparticle clusters as SERS substrates was also done. Herewith, an approach is provided to estimate the extent of plasmonic near-field enhancement both theoretically as well as experimentally.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 7.504
Times cited: 29
DOI: 10.1021/acsami.7b13965
|
|
|
“Analytic versus CFD approach for kinetic modeling of gas phase photocatalysis”. Verbruggen SW, Lenaerts S, Denys S, Chemical engineering journal 262, 1 (2015). http://doi.org/10.1016/J.CEJ.2014.09.041
Abstract: In this work two methods for determining the LangmuirHinshelwood kinetic parameters for a slit-shaped flat bed photocatalytic reactor are compared: an analytic mass transfer based model adapted from literature and a computational fluid dynamics (CFD) approach that was used in conjunction with a simplex optimization routine. Despite the differences between both approaches, similar values for the kinetic parameters and similar trends in terms of their UV intensity dependence were found. Using an effectiveness-NTU (number of transfer units) approach, the analytic mass transfer based method could quantify the relative contributions of the rate limiting steps through a reaction effectiveness parameter. The numeric CFD approach on the other hand could yield the two kinetic parameters that determine the photocatalytic reaction rate simultaneously. Furthermore, it proved to be more accurate as it accounts for the spatial variation of flow rate, reaction rate and concentrations at the surface of the photocatalyst. We elaborate this dual kinetic analysis with regard to the photocatalytic degradation of acetaldehyde in air over a silicon wafer coated with a layer of TiO2 P25 (Evonik) and study the usefulness and limitations of both strategies.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 6.216
Times cited: 30
DOI: 10.1016/J.CEJ.2014.09.041
|
|
|
“Biotemplated diatom silica-titania materials for air purification”. Van Eynde E, Tytgat T, Smits M, Verbruggen SW, Hauchecorne B, Lenaerts S, Photochemical &, photobiological sciences 12, 690 (2013). http://doi.org/10.1039/C2PP25229E
Abstract: We present a novel manufacture route for silicatitania photocatalysts using the diatom microalga Pinnularia sp. Diatoms self-assemble into porous silica cell walls, called frustules, with periodic micro-, meso- and macroscale features. This unique hierarchical porous structure of the diatom frustule is used as a biotemplate to incorporate titania by a solgel methodology. Important material characteristics of the modified diatom frustules under study are morphology, crystallinity, surface area, pore size and optical properties. The produced biosilicatitania material is evaluated towards photocatalytic activity for NOx abatement under UV radiation. This research is the first step to obtain sustainable, well-immobilised silicatitania photocatalysts using diatoms.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 2.344
Times cited: 18
DOI: 10.1039/C2PP25229E
|
|
|
“CFD investigation of a multi-tube photocatalytic reactor in non-steady-state conditions”. van Walsem J, Verbruggen SW, Modde B, Lenaerts S, Denys S, Chemical engineering journal 304, 808 (2016). http://doi.org/10.1016/J.CEJ.2016.07.028
Abstract: A novel multi-tube photoreactor is presented with a high efficiency (over 90% conversion) toward the degradation of acetaldehyde in air under UV conditions with an incident intensity of 2.1 mW cm−2. A CFD model was developed to simulate the transient adsorption and photocatalytic degradation processes of acetaldehyde in this reactor design and to estimate the corresponding kinetic parameters through an optimization routine using the experimentally determined outlet concentration profiles. The CFD model takes into account the entire reactor geometry and all relevant flow parameters, in contrast to analytical methods that often oversimplify the physical and chemical process characteristics. Using CFD, we show that both adsorption and desorption rate constants increase by respectively one and two orders of magnitude when the UV light is switched on, which clearly affects the transient behavior. The agreement of the experimental and modelled concentration profiles is excellent as evidenced by a coefficient of determination of at least 0.965. To demonstrate the reliability and accuracy of all parameters obtained from the modelling approach, an ultimate validation test was performed using other conditions than the ones used for estimating the kinetic parameters. The model was able to accurately simulate simultaneous adsorption, desorption and photocatalytic degradation.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 6.216
Times cited: 10
DOI: 10.1016/J.CEJ.2016.07.028
|
|
|
“CFD modeling of transient adsorption/desorption behavior in a gas phase photocatalytic fiber reactor”. Verbruggen SW, Keulemans M, van Walsem J, Tytgat T, Lenaerts S, Denys S, Chemical engineering journal 292, 42 (2016). http://doi.org/10.1016/J.CEJ.2016.02.014
Abstract: We present the use of computational fluid dynamics (CFD) for accurately determining the adsorption parameters of acetaldehyde on photocatalytic fiber filter material, integrated in a continuous flow system. Unlike the traditional analytical analysis based on Langmuir adsorption, not only steady-state situations but also transient phenomena can be accounted for. Air displacement effects in the reactor and gas detection cell are investigated and inherently made part of the model. Incorporation of a surface aldol condensation reaction in the CFD analysis further improves the accuracy of the model which enables to extract precise, intrinsic adsorption parameters for situations in which analytical analysis would otherwise fail.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 6.216
Times cited: 12
DOI: 10.1016/J.CEJ.2016.02.014
|
|
|
“Concept and validation of a fully automated photocatalytic test setup”. Tytgat T, Hauchecorne B, Smits M, Verbruggen S, Lenaerts S, Journal of laboratory automation 17, 134 (2012). http://doi.org/10.1177/2211068211424554
Abstract: Photocatalytic activity can be studied by several methods, each with its own strengths and weaknesses. To study photocatalytic activity in an easy, user-friendly, and realistic way, a completely new setup has been built. The setup is modularly constructed around Fourier transform infrared spectroscopy (FTIR) spectroscopy at the heart of it, resulting in great versatility. Complementary software has been written for automatic control of the setup and for processing the generated data. Two pollutants, oil and n-octane, are tested to validate the performance of the setup. These validation experiments confirm the usefulness and added value of the setup in general and of the FTIR detection methodology as well. It becomes clear that a system of online measurements with good repeatability, accuracy, and user-friendliness has been created.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 2.85
Times cited: 15
DOI: 10.1177/2211068211424554
|
|
|
“Controllable nitrogen doping in as deposited TiO2 film and its effect on post deposition annealing”. Deng S, Verbruggen SW, Lenaerts S, Martens JA, Van den Berghe S, Devloo-Casier K, Devulder W, Dendoover J, Deduytsche D, Detavernier C, Journal of vacuum science and technology: A: vacuum surfaces and films 32, 01a123 (2014). http://doi.org/10.1116/1.4847976
Abstract: In order to narrow the band gap of TiO2, nitrogen doping by combining thermal atomic layer deposition (TALD) of TiO2 and plasma enhanced atomic layer deposition (PEALD) of TiN has been implemented. By altering the ratio between TALD TiO2 and PEALD TiN, the as synthesized TiOxNy films showed different band gaps (from 1.91 eV to 3.14 eV). In situ x-ray diffraction characterization showed that the crystallization behavior of these films changed after nitrogen doping. After annealing in helium, nitrogen doped TiO2 films crystallized into rutile phase while for the samples annealed in air a preferential growth of the anatase TiO2 along (001) orientation was observed. Photocatalytic tests of the degradation of stearic acid were done to evaluate the effect of N doping on the photocatalytic activity.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 1.374
Times cited: 10
DOI: 10.1116/1.4847976
|
|
|
“Cyclist exposure to black carbon, ultrafine particles and heavy metals : an experimental study along two commuting routes near Antwerp, Belgium”. Hofman J, Samson R, Joosen S, Blust R, Lenaerts S, Environmental research 164, 530 (2018). http://doi.org/10.1016/J.ENVRES.2018.03.004
Abstract: Urban environments typically exhibit large atmospheric pollution variation, in both space and time. In contrast to traditional monitoring networks suffering from a limited spatial coverage, mobile platforms enable personalized high-resolution monitoring, providing valuable insights into personal atmospheric pollution exposure, and the identification of potential pollution hotspots. This study evaluated personal cyclist exposure to UFPs, BC and heavy metals whilst commuting near Antwerp, Belgium, by performing mobile measurements with wearable black carbon (BC) and ultrafine particle (UFP) instruments. Loaded micro-aethalometer filterstrips were chemically analysed and the inhaled pollutant dose determined from the exhibited heart rate. Considerable spatial pollutant variation was observed along the travelled routes, with distinct contributions from spatial factors (e.g. traffic intersections, urban park and market) and temporary events. On average 300% higher BC, 20% higher UFP and changing elemental concentrations are observed along the road traffic route (RT), when compared to the bicycle highway route (BH). Although the overall background pollution determines a large portion of the experienced personal exposure (in this case 53% for BC and 40% for UFP), cyclists can influence their personal atmospheric pollution exposure, by selecting less exposed commuting routes. Our results, hereby, strengthen the body of evidence in favour of further policy investments in isolated bicycle infrastructure.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Times cited: 9
DOI: 10.1016/J.ENVRES.2018.03.004
|
|
|
“Determination of intrinsic kinetic parameters in photocatalytic multi-tube reactors by combining the NTUm-method with radiation field modelling”. van Walsem J, Roegiers J, Modde B, Lenaerts S, Denys S, Chemical engineering journal 354, 1042 (2018). http://doi.org/10.1016/J.CEJ.2018.08.010
Abstract: In this work, we propose an adapted Number of Transfer Units (NTUm)-method as an effective tool to determine the Langmuir-Hinshelwood kinetic parameters for a photocatalytic multi-tube reactor. The Langmuir-Hinshelwood rate constant kLH and the Langmuir adsorption constant KL were determined from several experiments under different UV-irradiance conditions, resulting in irradiance depending values for kLH. In order to determine a unique, intrinsic empirical constant k0, valid for all irradiation conditions, we coupled the adapted NTUm-method with a radiation field model to predict UV-irradiance distribution inside the reactor. The final set of kinetic parameters were derived using a Generalized Reduced Gradient (GRG) nonlinear solving method in Matlab which minimizes the differences between model and experimental reactor outlet concentrations of acetaldehyde for various photocatalytic experiments under varying operating conditions, including inlet concentration, flow rate and UV-irradiance. An excellent agreement of the intrinsic empirical constant k0, derived from the coupled NTUm-radiation field model and an earlier published CFD approach was found, emphasizing its validity and reliability.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 6.216
Times cited: 2
DOI: 10.1016/J.CEJ.2018.08.010
|
|
|
“Development, performance and stability of sulfur-free, macrovoid-free BSCF capillaries for high temperature oxygen separation from air”. Buysse C, Kovalevsky A, Snijkers F, Buekenhoudt A, Mullens S, Luyten J, Kretzschmar J, Lenaerts S, Journal of membrane science 372, 239 (2011). http://doi.org/10.1016/J.MEMSCI.2011.02.011
Abstract: Capture and storage of CO2 (CCS) from fossil-fuel power plants is vital in order to counteract a pending anthropogenic global warming. High temperature oxygen transport perovskite membranes can fulfill an important role in the separation of oxygen from air needed in the oxy-fuel technologies for CCS. In this study we present the development, performance and stability of gastight, macrovoid-free and sulfur-free Ba0.5Sr0.5Co0.8Fe0.2O3 − δ (BSCF) mixed conductor capillary membranes prepared by phase-inversion spinning and sintering. A sulfur-free phase-inversion polymer was chosen in order to obtain a phase-pure BSCF crystal phase. Special attention was given to the polymer solution and ceramic spinning suspension in order to avoid macrovoids and achieve gastight membranes. The sulfur-free BSCF capillaries showed an average 4-point bending strength of 64 ± 8 MPa and a maximum oxygen flux of not, vert, similar5.3 Nml/(cm2 min) at 950 °C for an argon sweep flow rate of 125 Nml/min. The comparison of the performance of sulfur-free and sulfur-containing BSCF capillaries with similar dimensions revealed a profound impact of the sulfur contamination on both the oxygen flux and the activation energy of the overall oxygen transport mechanism. Both long-term oxygen permeation at different temperatures and post-operation analysis of a sulfur-free BSCF capillary were performed and discussed.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 6.035
Times cited: 32
DOI: 10.1016/J.MEMSCI.2011.02.011
|
|
|
“Effect of pretreatment and temperature on the properties of Pinnularia biosilica frustules”. Van Eynde E, Lenaerts B, Tytgat T, Verbruggen SW, Hauchecorne B, Blust R, Lenaerts S, RSC advances 4, 56200 (2014). http://doi.org/10.1039/C4RA09305D
Abstract: Diatoms are unicellular microalgae that self-assemble an intricate porous silica cell wall, called frustule. Diatom frustules possess a unique combination of physical and chemical properties (chemical inertness, high mechanical strength, large surface area, low density, good porosity and highly ordered features on the nano-to-micro scale) making diatom frustules suited for many nanotechnological applications. For most proposed applications the organic material covering the frustules needs to be removed. In this paper we investigate the effect of different frustule cleaning methods (drying, autoclavation, SDS/EDTA treatment, H2O2 treatment and HNO3 treatment) and subsequent heat treatment at different temperatures (105 °C, 350 °C, 550 °C and 750 °C) on the material characteristics of the diatom Pinnularia sp. Material characteristics under study are morphology, surface area, pore size, elemental composition and organic content. The cleaned Pinnularia frustules are subsequently investigated as adsorbents to remove methylene blue (MB) from aqueous solution.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 3.108
Times cited: 10
DOI: 10.1039/C4RA09305D
|
|
|
“Elucidating the photocatalytic degradation pathway of acetaldehyde : an FTIR in situ study under atmospheric conditions”. Hauchecorne B, Terrens D, Verbruggen S, Martens JA, van Langenhove H, Demeestere K, Lenaerts S, Applied catalysis : B : environmental 106, 630 (2011). http://doi.org/10.1016/J.APCATB.2011.06.026
Abstract: In this paper, new insights of the photocatalytic oxidation pathway of acetaldehyde are obtained by means of an in-house constructed FTIR in situ reactor. It is shown that there are generally three different intermediates present: acetic acid, formic acid and formaldehyde. By means of FTIR in situ spectroscopy, this study revealed that these intermediates are bound on the TiO2 surface in different ways, resulting in the presence of more intermediate species, such as molecularly adsorbed acetic acid, bidentate acetate, molecularly adsorbed formic acid, monodentate formate, bidentate formate, formaldehyde and dioxymethylene. Furthermore, spectroscopic evidence is obtained concerning the formation of 3-hydroxybutanal and crotonaldehyde upon adsorption of acetaldehyde on TiO2 prior to UV illumination. The presented results thus give new insights in the photocatalytic oxidation pathway of acetaldehyde.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 9.446
Times cited: 46
DOI: 10.1016/J.APCATB.2011.06.026
|
|
|
“Fabrication and oxygen permeability of gastight, macrovoid-free Ba0.5Sr0.5Co0.8Fe0.2O3-\delta capillaries for high temperature gas separation”. Buysse C, Kovalevsky A, Snijkers F, Buekenhoudt A, Mullens S, Luyten J, Kretzschmar J, Lenaerts S, Journal of membrane science 359, 86 (2010). http://doi.org/10.1016/J.MEMSCI.2009.10.030
Abstract: Oxygen-permeable perovskites with mixed ionic-electronic conducting properties can play an important role in the separation of oxygen from air which is needed in the oxy-fuel and pre-combustion technologies for the removal and capture of CO2. In this work, gastight, macrovoid-free Ba0.5Sr0.5Co0.8Fe0.2O3−δ (BSCF) capillaries were successfully shaped by a phase-inversion spinning technique, followed by calcination and sintering. It was found that both the rheology of the ceramic suspension and the composition of bore liquid and coagulation bath are key factors for making macrovoid-free green capillaries. Gastight BSCF capillaries were obtained by sintering for 5 h at 1100 °C. The sintered BSCF capillaries contained a significant amount of BaSO4 due to a reaction with the polysulfone binder during calcination. The oxygen permeation flux through the BSCF capillaries was measured and compared to literature data on BSCF disk and hollow fiber membranes measured in similar conditions.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 6.035
Times cited: 38
DOI: 10.1016/J.MEMSCI.2009.10.030
|
|
|
“A field study of the effectiveness of sacrificial anodes in ballast tanks of merchant ships”. De Baere K, Verstraelen H, Lemmens L, Lenaerts S, Dewil R, Van Ingelgem Y, Potters G, Journal of marine science and technology 19, 116 (2014). http://doi.org/10.1007/S00773-013-0232-3
Abstract: Sacrificial anodes have become a standard practice for the protection of ballast tanks of merchant vessels against corrosive damage. A well protected tank should extend the life span of a ship and consequently enhances its economic value. An in situ survey comprising more than 100 merchant vessels provided the opportunity to measure the impact of these anodes on the life expectancy of these vessels. Contrary to the general belief of these anodes beneficial effect, no significant difference was found in our observations in terms of corrosion occurrence between ship populations with and without sacrificial anodes, across all ship ages. This may be explained by the highly variable conditions and the complex geometry in a ballast tank severely impede optimal and straightforward installation of these anodes in these tanks. Also, poorly placed anodes in it may harm the integrity of the coating of the tank. We therefore plead for uniform and clear rules on anode installation and inspection.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 0.838
Times cited: 3
DOI: 10.1007/S00773-013-0232-3
|
|
|
“Harvesting hydrogen gas from air pollutants with an un-biased gas phase photo-electrochemical cell”. Verbruggen SW, Van Hal M, Bosserez T, Rongé, J, Hauchecorne B, Martens JA, Lenaerts S, Chemsuschem 10, 1413 (2017). http://doi.org/10.1002/CSSC.201601806
Abstract: The concept of an all-gas-phase photo-electrochemical cell (PEC) producing hydrogen gas from volatile organic contaminated gas and light is presented. Without applying any external bias, organic contaminants are degraded and hydrogen gas is produced in separate electrode compartments. The system works most efficiently with organic pollutants in inert carrier gas. In the presence of oxygen gas, the cell performs less efficiently but still significant photocurrents are generated, showing the cell can be run on organic contaminated air. The purpose of this study is to demonstrate new application opportunities of PEC technology and to encourage further advancement toward photo-electrochemical remediation of air pollution with the attractive feature of simultaneous energy recovery and pollution abatement.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 7.226
Times cited: 6
DOI: 10.1002/CSSC.201601806
|
|
|
“Hierarchically dual-mesoporous TiO2 microspheres for enhanced photocatalytic properties and lithium storage”. Xiao S, Lu Y, Xiao B-Y, Wu L, Song J-P, Xiao Y-X, Wu S-M, Hu J, Wang Y, Chang G-G, Tian G, Lenaerts S, Janiak C, Yang X-Y, Su B-L, Chemistry: a European journal 24, 13246 (2018). http://doi.org/10.1002/CHEM.201801933
Abstract: Hierarchically dual‐mesoporous TiO2 microspheres have been synthesized via a solvothermal process in the presence of 1‐butyl‐3‐methylmidazolium tetrafluoroborate ([BMIm][BF4]) and diethylenetriamine (DETA) as co‐templates. Secondary mesostructured defects in the hierarchical TiO2 microspheres produce the oxygen vacancies, which not only significantly enhance the photocatalytic activity on degrading methyl blue (over 1.7 times to P25) and acetone (over 2.9 times of P25), but which also are beneficial for lithium storage. Moreover, we propose a mechanism to obtain a better understanding of the role of dual mesoporosity of TiO2 microspheres for enhancing the molecular diffusion, ion transportation and electron transformation.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 5.317
Times cited: 6
DOI: 10.1002/CHEM.201801933
|
|