|
Records |
Links |
|
Author |
Hauchecorne, B.; Tytgat, T.; Terrens, D.; Vanpachtenbeke, F.; Lenaerts, S. |
|
|
Title |
Validation of a newly developed FTIR in situ reactor: real time study of photocatalytic degradation of nitric oxide |
Type |
A1 Journal article |
|
Year |
2010 |
Publication |
Infrared physics and technology |
Abbreviated Journal |
Infrared Phys Techn |
|
|
Volume |
53 |
Issue |
6 |
Pages |
469-473 |
|
|
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
For many years, photocatalysis has been proposed as one of the promising techniques to abate environmental pollutants. To improve these reactions it is vital to know the reaction mechanisms of the photocatalytic degradation. This new reactor will make it possible to study the catalytic surface at the moment the reactions occur. By the means of UV LED illumination there is no need of an external UV lamp and thus lowers the cost. The validation of this newly developed reactor is done by investigating the photocatalytic reaction mechanism of nitric oxide (NO) and comparing these findings with those already discussed in literature. From these results, it became clear that the newly developed FTIR in situ reactor allows real time study of photocatalytic degradations. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000285169400009 |
Publication Date |
2010-10-09 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1350-4495 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
1.713 |
Times cited |
12 |
Open Access |
|
|
|
Notes |
; ; |
Approved |
Most recent IF: 1.713; 2010 IF: 0.932 |
|
|
Call Number |
UA @ admin @ c:irua:84561 |
Serial |
6002 |
|
Permanent link to this record |
|
|
|
|
Author |
Van Wesenbeeck, K.; Hauchecorne, B.; Lenaerts, S. |
|
|
Title |
Study of positive and negative plasma catalytic oxidation of ethylene |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Environmental technology |
Abbreviated Journal |
Environ Technol |
|
|
Volume |
38 |
Issue |
12 |
Pages |
1554-1561 |
|
|
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
The effect of introducing a photocatalytically active coating inside a plasma unit is investigated. This technique combines the advantages of high product selectivity from catalysis and the fast start-up from plasma technology. In this study, a preselected TiO2 coating is applied on the collector electrode of a DC corona discharge unit as non-thermal plasma reactor, in order to study the oxidation of ethylene. For both positive and negative polarities an enhanced mineralization is observed while the formation of by-products drastically decreases. The plasma catalytic unit gave the best results when using negative polarity at a voltage of 15kV. This shows the potential of plasma catalysis as indoor air purification technology. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000402018900010 |
Publication Date |
2016-10-03 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0959-3330 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
1.751 |
Times cited |
1 |
Open Access |
|
|
|
Notes |
; The authors wish to thank the University of Antwerp for supporting and funding this research. ; |
Approved |
Most recent IF: 1.751 |
|
|
Call Number |
UA @ admin @ c:irua:144351 |
Serial |
5993 |
|
Permanent link to this record |
|
|
|
|
Author |
Maes, R.R.; Potters, G.; Fransen, E.; Cayetano, F.C.; Van Schaeren, R.; Lenaerts, S. |
|
|
Title |
Finding the optimal fatty acid composition for biodiesel improving the emissions of a one-cylinder diesel generator |
Type |
A1 Journal article |
|
Year |
2021 |
Publication |
Sustainability |
Abbreviated Journal |
Sustainability-Basel |
|
|
Volume |
13 |
Issue |
21 |
Pages |
12089 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Nitrogen oxides (NOx) and particulate matter (PM) currently are the main pollutants emitted by diesel engines. While there is a start in using hybrid and electric cars, ships will still be fueled by mineral oil products. In the quest to achieve zero-pollution and carbon-free shipping, alternative forms of energy carriers must be found to replace the commonly used mineral oil products. One of the possible alternative fuels is biodiesel. This paper explores the optimization of the composition of biodiesel in order to reduce the concentration of particulate matter and NOx in exhaust gases of a one-cylinder diesel generator. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000719122800001 |
Publication Date |
2021-11-03 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2071-1050 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
|
Impact Factor |
1.789 |
Times cited |
|
Open Access |
OpenAccess |
|
|
Notes |
|
Approved |
Most recent IF: 1.789 |
|
|
Call Number |
UA @ admin @ c:irua:184041 |
Serial |
7969 |
|
Permanent link to this record |
|
|
|
|
Author |
De Baere, K.; Verstraelen, H.; Rigo, P.; Van Passel, S.; Lenaerts, S.; Potters, G. |
|
|
Title |
Study on alternative approaches to corrosion protection of ballast tanks using an economic model |
Type |
A1 Journal article |
|
Year |
2013 |
Publication |
Marine structures |
Abbreviated Journal |
Mar Struct |
|
|
Volume |
32 |
Issue |
|
Pages |
1-17 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
One of the most relevant problems in ship construction and maintenance nowadays is corrosion in ballast tanks of modern merchant vessels. On the one hand, there is a general consensus that the economic lifespan of such a vessel depends, to a large degree, upon the corrosion state of its ballast tanks, while on the other hand these ballast tanks, located between the outer hull and the cargo tanks, makes routine inspection and maintenance a difficult task. Today, ship's ballast tanks are usually constructed in steel and protected with an epoxy coating backed up by sacrificial zinc anodes. Such a construction has been applied without significant alterations for many years. The objective of this economic study is to compare this construction method with some potential alternatives. The considered alternatives are: (1) an increase in structural scantlings, eliminating the necessity to replace corroded at a cost of real cargo carrying capacity of the ship, (2) application of the novel and more durable TSCF25 coating (3), the use of corrosion resistant steel in ship construction and (4) a standard PSPC15 coating combined with lifetime lasting aluminum sacrificial anodes. A cost model was used to evaluate these alternative options together with sensitivity analysis. It is concluded that the durable coating and the use of lifetime lasting aluminum anodes are bound to improve the actual basic tank concept. Corrosion resistant steel becomes attractive when the steel price becomes competitive. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000319643500001 |
Publication Date |
2013-03-27 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0951-8339 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.052 |
Times cited |
15 |
Open Access |
|
|
|
Notes |
; ; |
Approved |
Most recent IF: 2.052; 2013 IF: 1.242 |
|
|
Call Number |
UA @ admin @ c:irua:109346 |
Serial |
6253 |
|
Permanent link to this record |
|
|
|
|
Author |
De Baere, K.; Verstraelen, H.; Rigo, P.; Van Passel, S.; Lenaerts, S.; Potters, G. |
|
|
Title |
Reducing the cost of ballast tank corrosion : an economic modeling approach |
Type |
A1 Journal article |
|
Year |
2013 |
Publication |
Marine structures |
Abbreviated Journal |
Mar Struct |
|
|
Volume |
32 |
Issue |
|
Pages |
136-152 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
One of the most relevant problems in ship construction and maintenance nowadays concerns the corrosion in the double hull space ballast tanks of modern merchant vessels. On the one hand, there is a general consensus that the economic life span of such a vessel depends primarily upon the corrosion state of its ballast tanks, while on the other hand, the position of these tanks, squeezed between the outer hull and the loading tanks, makes routine inspection and maintenance almost impossible. Today, ship's ballast tanks are usually constructed in grade A steel and protected with a standard epoxy coating, backed up with sacrificial zinc anodes. Such a construction has been applied without significant alterations for many years. However, the objective of this economic study is to compare this construction method with some feasible alternatives. The considered alternatives are: (1) an increase of the scantlings, eliminating the necessity to replace corroded steel but diminishing the cargo carrying capacity of the ship, (2) application of the novel and more durable TSCF25 coating (3), the use of corrosion resistant steel in ship construction or (4) a standard PSPC15 coating combined with lifetime lasting aluminum sacrificial anodes. After running each alternative through a cost model including an extensive sensitivity analysis, it is concluded that the durable coating and the use of lifetime lasting aluminum anodes are bound to improve the actual basic tank concept. Corrosion resistant steel becomes attractive depending upon the evolution of the international steel market. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000319643500007 |
Publication Date |
2013-05-01 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0951-8339 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.052 |
Times cited |
9 |
Open Access |
|
|
|
Notes |
; ; |
Approved |
Most recent IF: 2.052; 2013 IF: 1.242 |
|
|
Call Number |
UA @ admin @ c:irua:109347 |
Serial |
6240 |
|
Permanent link to this record |
|
|
|
|
Author |
Van Eynde, E.; Tytgat, T.; Smits, M.; Verbruggen, S.W.; Hauchecorne, B.; Lenaerts, S. |
|
|
Title |
Biotemplated diatom silica-titania materials for air purification |
Type |
A1 Journal article |
|
Year |
2013 |
Publication |
Photochemical & photobiological sciences |
Abbreviated Journal |
Photoch Photobio Sci |
|
|
Volume |
12 |
Issue |
4 |
Pages |
690-695 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
We present a novel manufacture route for silicatitania photocatalysts using the diatom microalga Pinnularia sp. Diatoms self-assemble into porous silica cell walls, called frustules, with periodic micro-, meso- and macroscale features. This unique hierarchical porous structure of the diatom frustule is used as a biotemplate to incorporate titania by a solgel methodology. Important material characteristics of the modified diatom frustules under study are morphology, crystallinity, surface area, pore size and optical properties. The produced biosilicatitania material is evaluated towards photocatalytic activity for NOx abatement under UV radiation. This research is the first step to obtain sustainable, well-immobilised silicatitania photocatalysts using diatoms. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000316572500016 |
Publication Date |
2012-10-25 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1474-905x; 1474-9092 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.344 |
Times cited |
18 |
Open Access |
|
|
|
Notes |
; ; |
Approved |
Most recent IF: 2.344; 2013 IF: 2.939 |
|
|
Call Number |
UA @ admin @ c:irua:106625 |
Serial |
5930 |
|
Permanent link to this record |
|
|
|
|
Author |
Caretti, I.; Keulemans, M.; Verbruggen, S.W.; Lenaerts, S.; Van Doorslaer, S. |
|
|
Title |
Light-induced processes in plasmonic Gold/TiO2 photocatalysts studied by electron paramagnetic resonance |
Type |
A1 Journal article |
|
Year |
2015 |
Publication |
Topics in catalysis |
Abbreviated Journal |
Top Catal |
|
|
Volume |
58 |
Issue |
12 |
Pages |
776-782 |
|
|
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
X-band and W-band continuous-wave (CW) electron paramagnetic resonance (EPR) was used to study in situ light-induced (LI) mechanisms in commercial P90 titania (90 % anatase/10 % rutile) compared to plasmon-enhanced Au-P90 photocatalyst. These materials were excited using UV and 532 nm visible light to generate different excitation states and distinguish pure charge separation from plasmon-assisted resonance processes. Up to nine different photoinduced species of trapped electrons and holes were identified. LI CW EPR of P90 is presented for the first time, showing a UV excitation response similar to the well-known mixed-phase P25 titania. It is shown that incorporation of Au nanoparticles in Au-P90 and formation of a Schottky junction affects the charge separation state of the catalyst under UV light. Moreover, Au impregnation activated P90 through plasmon hot electron injection under visible light excitation (plasmonic sensitization effect). In general, EPR proved to be crucial to determine the different photoexciation paths and reactions that regulate plasmonic photocatalysis. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000360011200008 |
Publication Date |
2015-08-03 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1022-5528 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.486 |
Times cited |
22 |
Open Access |
|
|
|
Notes |
; IC and SVD acknowledge the Research Foundation-Flanders (FWO) for financial support (Grant G.0687.13). SV thanks FWO for financial support through a postdoctoral fellowship and MK acknowledges the agency for Innovation by Science and Technology in Flanders (IWT) for financial support (Ph.D. Grant). ; |
Approved |
Most recent IF: 2.486; 2015 IF: 2.365 |
|
|
Call Number |
UA @ admin @ c:irua:127413 |
Serial |
5968 |
|
Permanent link to this record |
|
|
|
|
Author |
Meire, M.; Verbruggen, S.W.; Lenaerts, S.; Lommens, P.; Van Der Voort, P.; Van Driessche, I. |
|
|
Title |
Microwave-assisted synthesis of mesoporous titania with increased crystallinity, specific surface area, and photocatalytic activity |
Type |
A1 Journal article |
|
Year |
2016 |
Publication |
Journal of materials science |
Abbreviated Journal |
J Mater Sci |
|
|
Volume |
51 |
Issue |
21 |
Pages |
9822-9829 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Mesoporous titanium dioxide is a material finding its use in a wide range of applications. For many of these, it is important to achieve a high degree of crystallinity in the material. It is generally accepted that the use of the soft templating approach to synthesize mesoporous titania, results in a compromise between crystallinity and specific surface area due to thermal instability of the used templates. In this paper, we explore how the use of microwave irradiation can influence the crystallinity, specific surface area, and the electronic properties of mesoporous titania. Therefore, we combined microwave radiation with an evaporation-induced self-assembly (EISA) synthesis. We show that additional microwave treatment at carefully chosen synthesis steps can enhance the crystallinity with 20 % without causing significant loss of surface area (>360 m2/g). Surface photovoltage measurements were used to investigate the electronic properties. The photocatalytic activity of the samples was evaluated in aqueous media by following the degradation of an industrial dye, methylene blue, and the herbicide isoproturon under UV irradiation and in gaseous media looking at the degradation of acetaldehyde, a common indoor pollutant under UVA irradiation. In all cases, the microwave treatment results in more active materials. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000381182200023 |
Publication Date |
2016-07-18 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0022-2461 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.599 |
Times cited |
8 |
Open Access |
|
|
|
Notes |
; M. Meire and S. W. Verbruggen acknowledge the FWO-Flanders (Fund for Scientific Research-Flanders) for financial support. We want to thank T. Planckaert for the N<INF>2</INF> sorption measurements, J. Watte for the XRD measurements, and professor K. De Buysser for the quantitative Rietveld refinements. ; |
Approved |
Most recent IF: 2.599 |
|
|
Call Number |
UA @ admin @ c:irua:140098 |
Serial |
5970 |
|
Permanent link to this record |
|
|
|
|
Author |
Sóti, V.; Lenaerts, S.; Cornet, I. |
|
|
Title |
Of enzyme use in cost-effective high solid simultaneous saccharification and fermentation processes |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Journal of biotechnology |
Abbreviated Journal |
J Biotechnol |
|
|
Volume |
270 |
Issue |
270 |
Pages |
70-76 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL); Biochemical Wastewater Valorization & Engineering (BioWaVE) |
|
|
Abstract |
Enzyme cost is considered to be one of the most significant factors defining the final product price in lignocellulose hydrolysis and fermentation. Enzyme immobilization and recycling can be a tool to decrease costs. However, high solid loading is a key factor towards high product titers, and recovery of immobilized enzymes from this thick liquid is often overlooked. This paper aims to evaluate the economic feasibility of immobilized enzymes in simultaneous saccharification and fermentation (SSF) of lignocellulose biomass in general, as well as the recuperation of magnetic immobilized enzymes (m-CLEAs) during high solid loading in simultaneous saccharification, detoxification and fermentation processes (SSDF) of lignocellulose biomass. Enzyme prices were obtained from general cost estimations by Klein-Marcuschamer et al. [Klein-Marcuschamer et al. (2012) Biotechnol. Bioeng. 109, 10831087]. During enzyme cost analysis, the influence of inoculum recirculation as well as a shortened fermentation time was explored. Both resulted in 15% decrease of final enzyme product price. Enzyme recuperation was investigated experimentally and 99.5 m/m% of m-CLEAs was recovered from liquid medium in one step, while 88 m/m% could still be recycled from a thick liquid with high solid concentrations (SSF fermentation broth). A mathematical model was constructed to calculate the cost of immobilized and free enzyme utilization and showed that, with current process efficiencies and commercial enzyme prices, the cost reduction obtained by enzyme immobilization can reach around 60% compared to free enzyme utilization, while lower enzyme prices will result in a lower percentage of immobilization related savings, but overall enzyme costs will decrease significantly. These results are applied in a case study, estimating the viability of shifting from sugar to lignocellulose substrate for a 100 t lactic acid fermentation batch. It was concluded that it will only be economically feasible if the enzymes are produced at the most optimistic variable cost and either the activity of the immobilized catalyst or the recovery efficiency is further increased. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000427556400009 |
Publication Date |
2018-02-08 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0168-1656 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.599 |
Times cited |
6 |
Open Access |
|
|
|
Notes |
; This research is financed by the University of Antwerp [project number 15 FA100 002]. ; |
Approved |
Most recent IF: 2.599 |
|
|
Call Number |
UA @ admin @ c:irua:149006 |
Serial |
5974 |
|
Permanent link to this record |
|
|
|
|
Author |
van Walsem, J.; Roegiers, J.; Modde, B.; Lenaerts, S.; Denys, S. |
|
|
Title |
Integration of a photocatalytic multi-tube reactor for indoor air purification in HVAC systems : a feasibility study |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Environmental Science and Pollution Research |
Abbreviated Journal |
Environ Sci Pollut R |
|
|
Volume |
25 |
Issue |
18 |
Pages |
18015-18026 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
This work is focused on an in-depth experimental characterization of multi-tube reactors for indoor air purification integrated in ventilation systems. Glass tubes were selected as an excellent photocatalyst substrate to meet the challenging requirements of the operating conditions in a ventilation system in which high flow rates are typical. Glass tubes show a low-pressure drop which reduces the energy demand of the ventilator, and additionally, they provide a large exposed surface area to allow interaction between indoor air contaminants and the photocatalyst. Furthermore, the performance of a range of P25-loaded sol-gel coatings was investigated, based on their adhesion properties and photocatalytic activities. Moreover, the UV light transmission and photocatalytic reactor performance under various operating conditions were studied. These results provide vital insights for the further development and scaling up of multi-tube reactors in ventilation systems which can provide a better comfort, improved air quality in indoor environments, and reduced human exposure to harmful pollutants. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000436879200071 |
Publication Date |
2018-04-24 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0944-1344; 1614-7499 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.741 |
Times cited |
3 |
Open Access |
|
|
|
Notes |
; J.V.W. acknowledges the Agentschap Innoveren and Ondernemen for a PhD fellowship. ; |
Approved |
Most recent IF: 2.741 |
|
|
Call Number |
UA @ admin @ c:irua:150946 |
Serial |
5967 |
|
Permanent link to this record |
|
|
|
|
Author |
Smits, M.; Vanpachtenbeke, F.; Horemans, B.; De Wael, K.; Hauchecorne, B.; Van Langenhove, H.; Demeestere, K.; Lenaerts, S. |
|
|
Title |
Effect of operating and sampling conditions on the exhaust gas composition of small-scale power generators |
Type |
A1 Journal article |
|
Year |
2012 |
Publication |
PLoS ONE |
Abbreviated Journal |
Plos One |
|
|
Volume |
7 |
Issue |
3 |
Pages |
e32825-e32825,10 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Small stationary diesel engines, like in generator sets, have limited emission control measures and are therefore responsible for 44% of the particulate matter (PM) emissions in the United States. The diesel exhaust composition depends on operating conditions of the combustion engine. Furthermore, the measurements are influenced by the used sampling method. This study examines the effect of engine loading and exhaust gas dilution on the composition of small-scale power generators. These generators are used in different operating conditions than road-transport vehicles, resulting in different emission characteristics. Experimental data were obtained for gaseous volatile organic compounds (VOC) and PM mass concentration, elemental composition and nitrate content. The exhaust composition depends on load condition because of its effect on fuel consumption, engine wear and combustion temperature. Higher load conditions result in lower PM concentration and sharper edged particles with larger aerodynamic diameters. A positive correlation with load condition was found for K, Ca, Sr, Mn, Cu, Zn and Pb adsorbed on PM, elements that originate from lubricating oil or engine corrosion. The nitrate concentration decreases at higher load conditions, due to enhanced nitrate dissociation to gaseous NO at higher engine temperatures. Dilution on the other hand decreases PM and nitrate concentration and increases gaseous VOC and adsorbed metal content. In conclusion, these data show that operating and sampling conditions have a major effect on the exhaust gas composition of small-scale diesel generators. Therefore, care must be taken when designing new experiments or comparing literature results. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000303836500012 |
Publication Date |
2012-03-19 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1932-6203 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.806 |
Times cited |
5 |
Open Access |
|
|
|
Notes |
; ; |
Approved |
Most recent IF: 2.806; 2012 IF: 3.730 |
|
|
Call Number |
UA @ admin @ c:irua:96545 |
Serial |
5581 |
|
Permanent link to this record |
|
|
|
|
Author |
Kummamuru, N.B.; Perreault, P.; Lenaerts, S. |
|
|
Title |
A new generalized empirical correlation for predicting methane hydrate equilibrium conditions in pure water |
Type |
A1 Journal article |
|
Year |
2021 |
Publication |
Industrial & Engineering Chemistry Research |
Abbreviated Journal |
Ind Eng Chem Res |
|
|
Volume |
60 |
Issue |
8 |
Pages |
3474-3483 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
This work contributes to a new generalized empirical correlation for predicting methane (CH4) hydrate equilibrium conditions in pure water. Unlike the conventional thermodynamic approach that involves complex reckoning, the proposed empirical equation is developed by regressing 215 experimental data points from the literature and validating with 45 data points for predicting methane hydrate equilibrium conditions in pure water. The new correlation is proposed for a temperature and pressure range of 273.2–303.48 K and 2.63–72.26 MPa, respectively. The accuracy and performance of the proposed correlation is quantitatively evaluated using statistical error analysis. The proposed correlation was able to estimate CH4 hydrate equilibrium conditions satisfactorily with an R2 of 0.99987. The overall error analysis for the proposed correlation shows fair agreement with the experimental data reported within the literature. Concurrently, the new correlation showed better performance in predicting equilibrium conditions compared to those calculated by other empirical correlations available in the literature within the investigated range. In addition, the proposed empirical equation is also checked to evaluate its efficacy in fitting each set of experimental binary/ternary methane hydrates (BTMH) and binary hydrogen hydrates (BHH) for an accurate representation of equilibrium data over a wide range of composition, pressure, and temperature conditions. A maximum percentage deviation of 0.58% and 0.24% was observed between experimental and calculated equilibrium conditions for BTMH and BHH, respectively. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000626326200017 |
Publication Date |
2021-02-19 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0888-5885; 1520-5045 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.843 |
Times cited |
|
Open Access |
Not_Open_Access |
|
|
Notes |
|
Approved |
Most recent IF: 2.843 |
|
|
Call Number |
UA @ admin @ c:irua:175862 |
Serial |
7394 |
|
Permanent link to this record |
|
|
|
|
Author |
Tytgat, T.; Hauchecorne, B.; Smits, M.; Verbruggen, S.; Lenaerts, S. |
|
|
Title |
Concept and validation of a fully automated photocatalytic test setup |
Type |
A1 Journal article |
|
Year |
2012 |
Publication |
Journal of laboratory automation |
Abbreviated Journal |
Jala-J Lab Autom |
|
|
Volume |
17 |
Issue |
2 |
Pages |
134-143 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Photocatalytic activity can be studied by several methods, each with its own strengths and weaknesses. To study photocatalytic activity in an easy, user-friendly, and realistic way, a completely new setup has been built. The setup is modularly constructed around Fourier transform infrared spectroscopy (FTIR) spectroscopy at the heart of it, resulting in great versatility. Complementary software has been written for automatic control of the setup and for processing the generated data. Two pollutants, oil and n-octane, are tested to validate the performance of the setup. These validation experiments confirm the usefulness and added value of the setup in general and of the FTIR detection methodology as well. It becomes clear that a system of online measurements with good repeatability, accuracy, and user-friendliness has been created. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000304775300006 |
Publication Date |
2014-07-23 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2211-0682 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.85 |
Times cited |
15 |
Open Access |
|
|
|
Notes |
; The authors disclosed receipt of the following financial support for the research and/or authorship of this article: This work was supported by a Ph.D. grant (T. Tytgat) funded by the Institute of Innovation by Science and Technology in Flanders (IWT) and by a Ph.D. grant (S. Verbruggen) from the Research Foundation of Flanders (FWO). Other funding was made possible by the University of Antwerp. ; |
Approved |
Most recent IF: 2.85; 2012 IF: 1.457 |
|
|
Call Number |
UA @ admin @ c:irua:96649 |
Serial |
5935 |
|
Permanent link to this record |
|
|
|
|
Author |
Buysse, C.; Michielsen, B.; Middelkoop, V.; Snijkers, F.; Buekenhondt, A.; Kretzschmar, J.; Lenaerts, S. |
|
|
Title |
Modeling of the performance of BSCF capillary membranes in four-end and three-end integration mode |
Type |
A1 Journal article |
|
Year |
2013 |
Publication |
Ceramics international |
Abbreviated Journal |
Ceram Int |
|
|
Volume |
39 |
Issue |
4 |
Pages |
4113-4123 |
|
|
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Owing to their high surface-to-volume ratio, there has been an increasing research interest in mixed ionic electronic conducting (MIEC) capillary membranes for large-scale high temperature oxygen separation applications. They offer an energy-efficient solution for high temperature combustion processes in oxy-fuel and pre-combustion CO2 capture technologies used in fossil fuel power plants. In order to assess the effectiveness of these membranes in power plant applications, the impact of the geometry of Ba0.5Sr0.5Co0.8Fe0.2O3-delta (BSCF) capillaries on their performance in the three-end and four-end integration modes has been investigated and thoroughly discussed. The model's parameters were derived from four-end mode lab-scale experiments using gas-tight, macrovoid free and sulfur-free BSCF capillary membranes that were prepared by a phase-inversion spinning technique. The results of this modeling study revealed that in the four-end mode higher average oxygen fluxes and smaller total membrane areas can be obtained than in the three-end mode. This is due to the higher pO(2) gradient across the membrane wall. (C) 2012 Elsevier Ltd and Techna Group S.r.l. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000318129100084 |
Publication Date |
2012-11-09 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0272-8842 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.986 |
Times cited |
4 |
Open Access |
|
|
|
Notes |
; The authors wish to thank all the VITO staff involved in the project for their continued support, and in particular B. Molenberghs, W. Doyen, H. Beckers and S. Mullens. C. Buysse would like to acknowledge funding from VITO and the University of Antwerp for a Ph.D. studentship. This work has been performed in the framework of the German Helmholtz Alliance Project “MEM-BRAIN”, aiming at the development of gas separation membranes for zero-emission fossil fuel power plants. ; |
Approved |
Most recent IF: 2.986; 2013 IF: 2.086 |
|
|
Call Number |
UA @ admin @ c:irua:109020 |
Serial |
5971 |
|
Permanent link to this record |
|
|
|
|
Author |
Smits, M.; Ling, Y.; Lenaerts, S.; Van Doorslaer, S. |
|
|
Title |
Photocatalytic removal of soot : unravelling of the reaction mechanism by EPR and in situ FTIR spectroscopy |
Type |
A1 Journal article |
|
Year |
2012 |
Publication |
ChemPhysChem : a European journal of chemical physics and physical chemistry |
Abbreviated Journal |
Chemphyschem |
|
|
Volume |
13 |
Issue |
18 |
Pages |
4251-4257 |
|
|
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Photocatalytic soot oxidation is studied on P25 TiO2 as an important model reaction for self-cleaning processes by means of electron paramagnetic resonance (EPR) and Fourier transform infrared (FTIR) spectroscopy. Contacting of carbon black with P25 leads on the one hand to a reduction of the local dioxygen concentration in the powder. On the other hand, the weakly adsorbed radicals on the carbon particles are likely to act as alternative traps for the photogenerated conduction-band electrons. We find furthermore that the presence of dioxygen and oxygen-related radicals is vital for the photocatalytic soot degradation. The complete oxidation of soot to CO2 is evidenced by in situ FTIR spectroscopy, no intermediate CO is detected during the photocatalytic process. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000313692600026 |
Publication Date |
2012-11-13 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1439-4235 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
3.075 |
Times cited |
9 |
Open Access |
|
|
|
Notes |
; This work was supported by the University of Antwerp (PhD grants of M. S. and Y.L.). We would like to thank Birger Hauchecorne for the scientific discussion. ; |
Approved |
Most recent IF: 3.075; 2012 IF: 3.349 |
|
|
Call Number |
UA @ admin @ c:irua:104568 |
Serial |
5980 |
|
Permanent link to this record |
|
|
|
|
Author |
Deng, S.; Verbruggen, S.W.; He, Z.; Cott, D.J.; Vereecken, P.M.; Martens, J.A.; Bals, S.; Lenaerts, S.; Detavernier, C. |
|
|
Title |
Atomic layer deposition-based synthesis of photoactive TiO2 nanoparticle chains by using carbon nanotubes as sacrificial templates |
Type |
A1 Journal article |
|
Year |
2014 |
Publication |
RSC advances |
Abbreviated Journal |
Rsc Adv |
|
|
Volume |
4 |
Issue |
23 |
Pages |
11648-11653 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Highly ordered and self supported anatase TiO2 nanoparticle chains were fabricated by calcining conformally TiO2 coated multi-walled carbon nanotubes (MWCNTs). During annealing, the thin tubular TiO2 coating that was deposited onto the MWCNTs by atomic layer deposition (ALD) was transformed into chains of TiO2 nanoparticles ([similar]12 nm diameter) with an ultrahigh surface area (137 cm2 per cm2 of substrate), while at the same time the carbon from the MWCNTs was removed. Photocatalytic tests on the degradation of acetaldehyde proved that these forests of TiO2 nanoparticle chains are highly photoactive under UV light because of their well crystallized anatase phase. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000332470000017 |
Publication Date |
2014-02-14 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2046-2069; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
3.108 |
Times cited |
45 |
Open Access |
Not_Open_Access |
|
|
Notes |
; The authors wish to thank the Research Foundation – Flanders (FWO) and UGENT-GOA-01G01513 for financial support. The authors acknowledge the European Research Council for funding under the European Union's Seventh Framework Programme (FP7/2007-2013)/ERC grant agreement no. 239865-COCOON and no. 246791-COUNTATOMS. JAM acknowledges the Flemish government for long-term structural funding (Methusalem). ; |
Approved |
Most recent IF: 3.108; 2014 IF: 3.840 |
|
|
Call Number |
UA @ lucian @ c:irua:117298 |
Serial |
168 |
|
Permanent link to this record |
|
|
|
|
Author |
Van Eynde, E.; Lenaerts, B.; Tytgat, T.; Verbruggen, S.W.; Hauchecorne, B.; Blust, R.; Lenaerts, S. |
|
|
Title |
Effect of pretreatment and temperature on the properties of Pinnularia biosilica frustules |
Type |
A1 Journal article |
|
Year |
2014 |
Publication |
RSC advances |
Abbreviated Journal |
Rsc Adv |
|
|
Volume |
4 |
Issue |
|
Pages |
56200-56206 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Diatoms are unicellular microalgae that self-assemble an intricate porous silica cell wall, called frustule. Diatom frustules possess a unique combination of physical and chemical properties (chemical inertness, high mechanical strength, large surface area, low density, good porosity and highly ordered features on the nano-to-micro scale) making diatom frustules suited for many nanotechnological applications. For most proposed applications the organic material covering the frustules needs to be removed. In this paper we investigate the effect of different frustule cleaning methods (drying, autoclavation, SDS/EDTA treatment, H2O2 treatment and HNO3 treatment) and subsequent heat treatment at different temperatures (105 °C, 350 °C, 550 °C and 750 °C) on the material characteristics of the diatom Pinnularia sp. Material characteristics under study are morphology, surface area, pore size, elemental composition and organic content. The cleaned Pinnularia frustules are subsequently investigated as adsorbents to remove methylene blue (MB) from aqueous solution. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000344997800060 |
Publication Date |
2014-10-23 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2046-2069 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
3.108 |
Times cited |
10 |
Open Access |
|
|
|
Notes |
; ; |
Approved |
Most recent IF: 3.108; 2014 IF: 3.840 |
|
|
Call Number |
UA @ admin @ c:irua:121377 |
Serial |
5945 |
|
Permanent link to this record |
|
|
|
|
Author |
Sóti, V.; Jacquet, N.; Apers, S.; Richel, A.; Lenaerts, S.; Cornet, I. |
|
|
Title |
Monitoring the laccase reaction of vanillin and poplar hydrolysate |
Type |
A1 Journal article |
|
Year |
2016 |
Publication |
Journal of chemical technology and biotechnology |
Abbreviated Journal |
J Chem Technol Biot |
|
|
Volume |
91 |
Issue |
6 |
Pages |
1914-1922 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL); Biochemical Wastewater Valorization & Engineering (BioWaVE) |
|
|
Abstract |
BACKGROUND Laccase is an intensively researched enzyme for industrial use. Except for decolorisation measurements, HPLC analysis is the conventional method for monitoring the phenolic removal during laccase enzyme reaction. This paper reports an investigation of the continuous UV absorbance follow-up of the laccase reaction with steam pretreated poplar hydrolysate. RESULTS Vanillin was used as a model substrate and lignocellulose xylose rich fraction (XRF) as a biologically complex substrate for laccase detoxification. The reaction was followed by HPLC-UV as well as by UV spectrometric measurements. Results suggest that the reaction can be successfully monitored by measuring the change of UV absorbance at 280 nm, without previous compound separation. In case of XRF experiments the spectrophotometric follow-up is especially useful, as HPLC analysis takes a long time and provides less information than in case of single substrates. The method seems to be suitable for optimization and process control. CONCLUSION The obtained results can help to construct a fast, easy and straightforward monitoring system for laccase-phenolic substrate reactions. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000375768300040 |
Publication Date |
2015-07-29 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0268-2575; 1097-4660 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
3.135 |
Times cited |
3 |
Open Access |
|
|
|
Notes |
; This research is financed by the University of Antwerp (project number 15 FA100 002). ; |
Approved |
Most recent IF: 3.135 |
|
|
Call Number |
UA @ admin @ c:irua:127694 |
Serial |
5972 |
|
Permanent link to this record |
|
|
|
|
Author |
Huyskens, C.; De Wever, H.; Fovet, Y.; Wegmann, U.; Diels, L.; Lenaerts, S. |
|
|
Title |
Screening of novel MBR fouling reducers : benchmarking with known fouling reducers and evaluation of their mechanism of action |
Type |
A1 Journal article |
|
Year |
2012 |
Publication |
Separation and purification technology |
Abbreviated Journal |
Sep Purif Technol |
|
|
Volume |
95 |
Issue |
|
Pages |
49-57 |
|
|
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
A novel fouling characterization method was applied for a first screening of two novel synthetic flocculants developed by BASF (BASF-1 and BASF-2) and benchmarking with six well-known products. Results showed that this MBR-VITO Fouling Measurement (VFM) was able to identify beneficial and adverse effects of different additives on the mixed liquor's reversible and irreversible fouling and, in combination with supporting mixed liquor analyses, allowed to identify the additive's main working mechanism. The first screening tests indicated that BASF-1 and BASF-2 reduced reversible and irreversible fouling to a similar extent as the known synthetic flocculants due to a charge neutralization mechanism, resulting in enhanced flocculation and SMP removal. Further testing at different additive concentrations provided a first indication of the optimal dosage and revealed a considerable risk of overdosing for BASF-2, rendering it less suited for fouling control. In contrast, such adverse effects were not observed for BASF-1. BASF-1 induced similar beneficial effects as the known MPE50 polymer at lower dosage and was therefore considered promising for application in MBRs. (C) 2012 Elsevier B.V. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000307032100008 |
Publication Date |
2012-04-26 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1383-5866 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
3.359 |
Times cited |
24 |
Open Access |
|
|
|
Notes |
; The authors would like to thank K. Luyckx, J. Fret, L. Heylen, R. Muyshondt, H. Sterckx, J. Verheyden and J. Vande-Velden for technical assistance and V. Iversen for kindly supplying some of the commercial additives. Celine Huyskens is indebted to the Research Foundation-Flanders (FWO). The European Commission is acknowledged for financial support to Aquafit4use (FP7, Grant 211534). ; |
Approved |
Most recent IF: 3.359; 2012 IF: 2.894 |
|
|
Call Number |
UA @ admin @ c:irua:101903 |
Serial |
5990 |
|
Permanent link to this record |
|
|
|
|
Author |
Huyskens, C.; Lenaerts, S.; Brauns, E.; Diels, L.; de Wever, H. |
|
|
Title |
Study of (ir)reversible fouling in MBRs under various operating conditions using new on-line fouling sensor |
Type |
A1 Journal article |
|
Year |
2011 |
Publication |
Separation and purification technology |
Abbreviated Journal |
Sep Purif Technol |
|
|
Volume |
81 |
Issue |
2 |
Pages |
208-215 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
In this study, a new fouling sensor was validated under different conditions of hydraulic (HRT) and sludge retention time (SRT). The MBR-VFM (membrane bioreactor-VITO Fouling Measurement) allows the simultaneous determination of the physically reversible and irreversible fouling potential of a mixed liquor during a single crossflow filtration test. In accordance with the on-line filtration behavior, the measured reversible and irreversible fouling propensities differed significantly between MBRs operated at different combinations of HRT-SRT. Moreover, a significant negative correlation was found between the on-line permeability and the reversible and irreversible fouling propensity measured by the MBR-VFM. This corresponded to observations made on membrane recovery after physical or chemical cleaning actions. Higher reversible and irreversible fouling were observed at lower HRT, presumably as a consequence of increased concentrations of foulants present. The effect of SRT was much smaller and restricted to the reversible fouling component. Possible explanations for the increased fouling at prolonged SRT are the higher sludge and colloid concentration and the smaller floc size. It can be concluded that the MBR-VFM is a useful tool to monitor fluctuations in a mixed liquors (ir)reversible fouling potential and can contribute to a deeper understanding of the occurring fouling phenomena. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000296108500012 |
Publication Date |
2011-08-01 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1383-5866 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
3.359 |
Times cited |
15 |
Open Access |
|
|
|
Notes |
; ; |
Approved |
Most recent IF: 3.359; 2011 IF: 2.921 |
|
|
Call Number |
UA @ admin @ c:irua:93410 |
Serial |
5992 |
|
Permanent link to this record |
|
|
|
|
Author |
Blommaerts, N.; Dingenen, F.; Middelkoop, V.; Savelkouls, J.; Goemans, M.; Tytgat, T.; Verbruggen, S.W.; Lenaerts, S. |
|
|
Title |
Ultrafast screening of commercial sorbent materials for VOC adsorption using real-time FTIR spectroscopy |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Separation and purification technology |
Abbreviated Journal |
Sep Purif Technol |
|
|
Volume |
207 |
Issue |
207 |
Pages |
284-290 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Recovery of valuable volatile organic compounds (VOCs) from waste streams is of great industrial importance. Adsorption on zeolites offers an economically and environmentally friendly alternative to conventional activated carbon. When evaluating the suitability of a given zeolite for a particular adsorption application, its adsorption capacity has to be determined. This is traditionally achieved using gas chromatography as an analysis tool, yielding only a few discrete sampling points that constitute the adsorption profile. Meanwhile, only low flow rates and low concentrations of volatile organics can be used, rendering the procedure troublesome and time consuming. Herein, we propose a tool for the fast screening of a large amount of zeolites using on-line and quasi real-time Fourier Transform Infrared Spectroscopy (FTIR). The technique was used to determine the adsorption capacity of three different commercial zeolites and two silica gels, for five industrially relevant VOCs: acetone; methanol; isohexane; isopentane; and toluene. A series of rapid measurements of the individual adsorption capacities were carried out to obtain a detailed overview of the versatility of the proposed method for the characterization of multi-component and multi-sorption bed systems. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000445987500032 |
Publication Date |
2018-06-27 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1383-5866 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
3.359 |
Times cited |
5 |
Open Access |
|
|
|
Notes |
; We would like to thank Vlaams Agenschap Innoveren & Ondernemen (VLAIO) for financial support. The authors would also like to thank Kureha GmbH, Germany for kindly supplying us with their BAC (R) (bead-shaped activated carbon) samples. ; |
Approved |
Most recent IF: 3.359 |
|
|
Call Number |
UA @ admin @ c:irua:154694 |
Serial |
6000 |
|
Permanent link to this record |
|
|
|
|
Author |
Peeters, H.; Lenaerts, S.; Verbruggen, S.W. |
|
|
Title |
Benchmarking the photocatalytic self-cleaning activity of industrial and experimental materials with ISO 27448:2009 |
Type |
A1 Journal article |
|
Year |
2023 |
Publication |
Materials |
Abbreviated Journal |
Materials |
|
|
Volume |
16 |
Issue |
3 |
Pages |
1119-13 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology |
|
|
Abstract |
Various industrial surface materials are tested for their photocatalytic self-cleaning activity by performing the ISO 27448:2009 method. The samples are pre-activated by UV irradiation, fouled with oleic acid and irradiated by UV light. The degradation of oleic acid over time is monitored by taking water contact angle measurements using a contact angle goniometer. The foulant, oleic acid, is an organic acid that makes the surface more hydrophobic. The water contact angle will thus decrease over time as the photocatalytic material degrades the oleic acid. In this study, we argue that the use of this method is strongly limited to specific types of surface materials, i.e., only those that are hydrophilic and smooth in nature. For more hydrophobic materials, the difference in the water contact angles of a clean surface and a fouled surface is not measurable. Therefore, the photocatalytic self-cleaning activity cannot be established experimentally. Another type of material that cannot be tested by this standard are rough surfaces. For rough surfaces, the water contact angle cannot be measured accurately using a contact angle goniometer as prescribed by the standard. Because of these limitations, many potentially interesting industrial substrates cannot be evaluated. Smooth samples that were treated with an in-house developed hydrophilic titania thin film (PCT/EP2018/079983) showed a great photocatalytic self-cleaning performance according to the ISO standard. Apart from discussing the pros and cons of the current ISO standard, we also stress how to carefully interpret the results and suggest alternative testing solutions. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000930734100001 |
Publication Date |
2023-01-30 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1996-1944 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
3.4 |
Times cited |
|
Open Access |
OpenAccess |
|
|
Notes |
|
Approved |
Most recent IF: 3.4; 2023 IF: 2.654 |
|
|
Call Number |
UA @ admin @ c:irua:193337 |
Serial |
7284 |
|
Permanent link to this record |
|
|
|
|
Author |
Dingenen, F.; Blommaerts, N.; Van Hal, M.; Borah, R.; Arenas-Esteban, D.; Lenaerts, S.; Bals, S.; Verbruggen, S.W. |
|
|
Title |
Layer-by-Layer-Stabilized Plasmonic Gold-Silver Nanoparticles on TiO2: Towards Stable Solar Active Photocatalysts |
Type |
A1 Journal article |
|
Year |
2021 |
Publication |
Nanomaterials |
Abbreviated Journal |
Nanomaterials-Basel |
|
|
Volume |
11 |
Issue |
10 |
Pages |
2624 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
To broaden the activity window of TiO2, a broadband plasmonic photocatalyst has been designed and optimized. This plasmonic ‘rainbow’ photocatalyst consists of TiO2 modified with gold–silver composite nanoparticles of various sizes and compositions, thus inducing a broadband interaction with polychromatic solar light. However, these nanoparticles are inherently unstable, especially due to the use of silver. Hence, in this study the application of the layer-by-layer technique is introduced to create a protective polymer shell around the metal cores with a very high degree of control. Various TiO2 species (pure anatase, PC500, and P25) were loaded with different plasmonic metal loadings (0–2 wt %) in order to identify the most solar active composite materials. The prepared plasmonic photocatalysts were tested towards stearic acid degradation under simulated sunlight. From all materials tested, P25 + 2 wt % of plasmonic ‘rainbow’ nanoparticles proved to be the most promising (56% more efficient compared to pristine P25) and was also identified as the most cost-effective. Further, 2 wt % of layer-by-layer-stabilized ‘rainbow’ nanoparticles were loaded on P25. These layer-by-layer-stabilized metals showed superior stability under a heated oxidative atmosphere, as well as in a salt solution. Finally, the activity of the composite was almost completely retained after 1 month of aging, while the nonstabilized equivalent lost 34% of its initial activity. This work shows for the first time the synergetic application of a plasmonic ‘rainbow’ concept and the layer-by-layer stabilization technique, resulting in a promising solar active, and long-term stable photocatalyst. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000712759800001 |
Publication Date |
2021-10-06 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2079-4991 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
3.553 |
Times cited |
7 |
Open Access |
OpenAccess |
|
|
Notes |
Research was funded by Research Foundation—Flanders (FWO), FN 700300001— Aspirant F. Dingenen. |
Approved |
Most recent IF: 3.553 |
|
|
Call Number |
EMAT @ emat @c:irua:183281 |
Serial |
6812 |
|
Permanent link to this record |
|
|
|
|
Author |
Maes, R.R.; Potters, G.; Fransen, E.; Geuens, J.; Van Schaeren, R.; Lenaerts, S. |
|
|
Title |
Can we find an optimal fatty acid composition of biodiesel in order to improve oxidation stability? |
Type |
A1 Journal article |
|
Year |
2023 |
Publication |
Sustainability |
Abbreviated Journal |
|
|
|
Volume |
15 |
Issue |
13 |
Pages |
10310-10 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL); Medical Genetics (MEDGEN) |
|
|
Abstract |
Air quality currently poses a major risk for human health. Currently, diesel is widely used as fuel and is a significant source of nitrogen oxides (NOx) and particulate matter (PM), both hazardous to human health. A good alternative for mineral diesel is biodiesel, not only for the improvement of hazardous components in the exhaust gases but also because it can be produced in view of a circular economy. Biodiesel consists of a mix of different fatty acid methyl esters, which can react with oxygen. As a consequence, the oxidation stability of biodiesel has to be studied, because the oxidation of biodiesel could affect the performance of the engine due to the wear of injectors and fuel pumps. The oxidation stability could also affect the quality of the exhaust gases due to increases in NOx and PM. The basic question we try to answer in this communication is: 'Can we find an optimal fatty acid composition in order to have a maximal oxidation stability?' In this article, we try to find the optimal fatty acid composition according to the five most common fatty acid methyl esters present in biodiesel in order to reach a maximal oxidation stability. The measurements and statistical analysis show, however, that there is no useful regression model because there are statistically significant two- and three-way interactions among the different fatty acids. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
001028597300001 |
Publication Date |
2023-06-30 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2071-1050 |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
|
Impact Factor |
3.9 |
Times cited |
|
Open Access |
OpenAccess |
|
|
Notes |
|
Approved |
Most recent IF: 3.9; 2023 IF: 1.789 |
|
|
Call Number |
UA @ admin @ c:irua:198241 |
Serial |
8839 |
|
Permanent link to this record |
|
|
|
|
Author |
Dong, Y.; Chen, S.-Y.; Lu, Y.; Xiao, Y.-X.; Hu, J.; Wu, S.-M.; Deng, Z.; Tian, G.; Chang, G.-G.; Li, J.; Lenaerts, S.; Janiak, C.; Yang, X.-Y.; Su, B.-L. |
|
|
Title |
Hierarchical MoS2@TiO2 heterojunctions for enhanced photocatalytic performance and electrocatalytic hydrogen evolution |
Type |
A1 Journal article |
|
Year |
2018 |
Publication |
Chemistry: an Asian journal |
Abbreviated Journal |
Chem-Asian J |
|
|
Volume |
13 |
Issue |
12 |
Pages |
1609-1615 |
|
|
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Hierarchical MoS2@TiO2 heterojunctions were synthesized through a one-step hydrothermal method by using protonic titanate nanosheets as the precursor. The TiO2 nanosheets prevent the aggregation of MoS2 and promote the carrier transfer efficiency, and thus enhance the photocatalytic and electrocatalytic activity of the nanostructured MoS2. The obtained MoS2@TiO2 has significantly enhanced photocatalytic activity in the degradation of rhodamineB (over 5.2times compared with pure MoS2) and acetone (over 2.8times compared with pure MoS2). MoS2@TiO2 is also beneficial for electrocatalytic hydrogen evolution (26times compared with pure MoS2, based on the cathodic current density). This work offers a promising way to prevent the self-aggregation of MoS2 and provides a new insight for the design of heterojunctions for materials with lattice mismatches. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000435773300011 |
Publication Date |
2018-04-10 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1861-4728; 1861-471x |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
4.083 |
Times cited |
22 |
Open Access |
|
|
|
Notes |
; This work was supported by the National Key R&D Program of China (2017YFC1103800), PCSIRT (IRT15R52), NSFC (U1662134, U1663225, 51472190, 51611530672, 51503166, 21706199, 21711530705), ISTCP (2015DFE52870), HPNSF (2016CFA033, 2017CFB487), and SKLPPC (PPC2016007). ; |
Approved |
Most recent IF: 4.083 |
|
|
Call Number |
UA @ admin @ c:irua:151971 |
Serial |
5956 |
|
Permanent link to this record |
|
|
|
|
Author |
Goemans, M.; Clarysse, P.; Joannès, J.; de Clercq, P.; Lenaerts, S.; Matthys, K.; Boels, K. |
|
|
Title |
Catalytic Nox reduction with simultaneous dioxin and furan oxidation |
Type |
A1 Journal article |
|
Year |
2004 |
Publication |
Chemosphere |
Abbreviated Journal |
Chemosphere |
|
|
Volume |
54 |
Issue |
9 |
Pages |
1357-1365 |
|
|
Keywords |
A1 Journal article |
|
|
Abstract |
The engineering, construction, performance and running costs of a catalytic flue gas cleaning component in the low dust area of a municipal waste incinerator is discussed. For this purpose, the case study of a Flemish incineration plant is presented, covering the history, the design procedure of the catalyst, relevant process data and the financial aspects. A reliable PCDD/F-destruction by means of oxidation by the catalyst to typical values of 0.001 ng TEQ/Nm3 has been demonstrated. At the same time, NOx− and CO-emissions are reduced by 90% and 20% to about 50 mg/Nm3 and below 10 mg/Nm3, respectively. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000188293500011 |
Publication Date |
2003-12-02 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0045-6535; 1879-1298 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles; WoS full record; WoS citing articles |
|
|
Impact Factor |
4.208 |
Times cited |
|
Open Access |
|
|
|
Notes |
|
Approved |
Most recent IF: 4.208; 2004 IF: 2.359 |
|
|
Call Number |
UA @ admin @ c:irua:82011 |
Serial |
5931 |
|
Permanent link to this record |
|
|
|
|
Author |
Goemans, M.; Clarysse, P.; Joannès, J.; de Clercq, P.; Lenaerts, S.; Matthys, K.; Boels, K. |
|
|
Title |
Catalytic Nox reduction with simultaneous dioxin and furan oxidation |
Type |
A1 Journal article |
|
Year |
2003 |
Publication |
Chemosphere |
Abbreviated Journal |
Chemosphere |
|
|
Volume |
50 |
Issue |
4 |
Pages |
489-497 |
|
|
Keywords |
A1 Journal article |
|
|
Abstract |
The engineering, construction, performance and running costs of a catalytic flue gas cleaning component in the low dust area of a municipal waste incinerator is discussed. For this purpose, the case study of a Flemish incineration plant is presented, covering the history, the design procedure of the catalyst, relevant process data and the financial aspects. A reliable PCDD/F-destruction by means of oxidation by the catalyst to typical values of 0.001 ng TEQ/N m3 has been demonstrated. At the same time, NOx- and CO-emissions are reduced by 90% and 20% to about 50 mg/N m3 and below 10 mg/N m3, respectively. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000180078200004 |
Publication Date |
2002-12-10 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0045-6535; 1879-1298 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles; WoS full record; WoS citing articles |
|
|
Impact Factor |
4.208 |
Times cited |
|
Open Access |
|
|
|
Notes |
|
Approved |
Most recent IF: 4.208; 2003 IF: 1.904 |
|
|
Call Number |
UA @ admin @ c:irua:82010 |
Serial |
5932 |
|
Permanent link to this record |
|
|
|
|
Author |
Ramakers, M.; Heijkers, S.; Tytgat, T.; Lenaerts, S.; Bogaerts, A. |
|
|
Title |
Combining CO2 conversion and N2 fixation in a gliding arc plasmatron |
Type |
A1 Journal article |
|
Year |
2019 |
Publication |
Journal of CO2 utilization |
Abbreviated Journal |
J Co2 Util |
|
|
Volume |
33 |
Issue |
|
Pages |
121-130 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT); Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Industry needs a flexible and efficient technology to convert CO2 into useful products, which fits in the Carbon Capture and Utilization (CCU) philosophy. Plasma technology is intensively being investigated for this purpose. A promising candidate is the gliding arc plasmatron (GAP). Waste streams of CO2 are often not pure and contain N2 as important impurity. Therefore, in this paper we provide a detailed experimental and computational study of the combined CO2 and N2 conversion in a GAP. Is it possible to take advantage of the presence of N2 in the mixture and to combine CO2 conversion with N2 fixation? Our experiments and simulations reveal that N2 actively contributes to the process of CO2 conversion, through its vibrational levels. In addition, NO and NO2 are formed, with concentrations around 7000 ppm, which is slightly too low for valorization, but by improving the reactor design it must be possible to further increase their concentrations. Other NO-based molecules, in particular the strong greenhouse gas N2O, are not formed in the GAP, which is an important result. We also compare our results with those obtained in other plasma reactors to clarify the differences in underlying plasma processes, and to demonstrate the superiority of the GAP. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000487274100013 |
Publication Date |
2019-05-22 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2212-9820 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
4.292 |
Times cited |
3 |
Open Access |
Not_Open_Access: Available from 23.05.2021
|
|
|
Notes |
Fund for Scientific Research Flanders, G.0383.16N ; Excellence of Science program of the Fund for Scientific Research, G0F9618N ; Hercules Foundation, the Flemish Government; UAntwerpen; We acknowledge financial support from the Fund for Scientific Research Flanders (FWO; Grant no. G.0383.16N) and the Excellence of Science program of the Fund for Scientific Research (FWO-FNRS; Grant no. G0F9618N; EOS ID: 30505023). The calculations were performed using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UAntwerpen), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UAntwerpen. Finally, we also want to thank Dr. Ramses Snoeckx for the very interesting discussions, and A. Fridman and A. Rabinovich for developing the GAP. |
Approved |
Most recent IF: 4.292 |
|
|
Call Number |
PLASMANT @ plasmant @UA @ admin @ c:irua:159984 |
Serial |
5173 |
|
Permanent link to this record |
|
|
|
|
Author |
Liu, J.-W.; Wu, S.-M.; Wang, L.-Y.; Tian, G.; Qin, Y.; Wu, J.-X.; Zhao, X.-F.; Zhang, Y.-X.; Chang, G.-G.; Wu, L.; Zhang, Y.-X.; Li, Z.-F.; Guo, C.-Y.; Janiak, C.; Lenaerts, S.; Yang, X.-Y. |
|
|
Title |
Pd/Lewis acid synergy in macroporous Pd@Na-ZSM-5 for enhancing selective conversion of biomass |
Type |
A1 Journal article |
|
Year |
2020 |
Publication |
Chemcatchem |
Abbreviated Journal |
Chemcatchem |
|
|
Volume |
|
Issue |
|
Pages |
1-6 |
|
|
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Pd nanometal particles encapsulated in macroporous Na-ZSM-5 with only Lewis acid sites have been successfully synthesized by a steam-thermal approach. The synergistic effect of Pd and Lewis acid sites have been investigated for significant enhancement of the catalytic selectivity towards furfural alcohol in furfural hydroconversion. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000554645800001 |
Publication Date |
2020-07-11 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1867-3880; 1867-3899 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
4.5 |
Times cited |
1 |
Open Access |
|
|
|
Notes |
; We acknowledge a joint DFG-NSFC project (DFG JA466/39-1, NSFC grant 51861135313). This work was also supported by National Key R&D Program of China (2017YFC1103800), NSFC (U1662134, 21711530705), Jilin Province Science and Technology Development Plan (20180101208JC), HPNSF (2016CFA033), FRFCU (19lgzd16) and ISTCP (2015DFE52870). ; |
Approved |
Most recent IF: 4.5; 2020 IF: 4.803 |
|
|
Call Number |
UA @ admin @ c:irua:171178 |
Serial |
6579 |
|
Permanent link to this record |
|
|
|
|
Author |
Kurttepeli, M.; Deng, S.; Verbruggen, S.W.; Guzzinati, G.; Cott, D.J.; Lenaerts, S.; Verbeeck, J.; Van Tendeloo, G.; Detavernier, C.; Bals, S. |
|
|
Title |
Synthesis and characterization of photoreactive TiO2carbon nanosheet composites |
Type |
A1 Journal article |
|
Year |
2014 |
Publication |
The journal of physical chemistry: C : nanomaterials and interfaces |
Abbreviated Journal |
J Phys Chem C |
|
|
Volume |
118 |
Issue |
36 |
Pages |
21031-21037 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
We report the atomic layer deposition of titanium dioxide on carbon nanosheet templates and investigate the effects of postdeposition annealing in a helium environment using different characterization techniques. The crystallization of the titanium dioxide coating upon annealing is observed using in situ X-ray diffraction. The (micro)structural characterization of the films is carried out by scanning electron microscopy and advanced transmission electron microscopy techniques. Our study shows that the annealing of the atomic layer deposition processed and carbon nanosheets templated titanium dioxide layers in helium environment resulting in the formation of a porous, nanocrystalline and photocatalytically active titanium dioxide-carbon nanosheet composite film. Such composites are suitable for photocatalysis and dye-sensitized solar cells applications. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
Washington, D.C. |
Editor |
|
|
|
Language |
|
Wos |
000341619500034 |
Publication Date |
2014-08-23 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1932-7447;1932-7455; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
4.536 |
Times cited |
9 |
Open Access |
OpenAccess |
|
|
Notes |
This research was funded by the Flemish research foundation FWO-Vlaanderen, by the European Research Council (Starting Grant No. 239865) and by the Special Research Fund BOF of Ghent University (GOA-01G01513). G.G, M.K., J.V., S.B., and G.V.T. acknowledge funding from the European Research Council under the seventh Framework Program (FP7), ERC Starting Grant No. 278510 VORTEX and No. 335078 COLOURATOMS. ECASJO;; ECASSara; (ROMEO:white; preprint:; postprint:restricted 12 months embargo; pdfversion:cannot); |
Approved |
Most recent IF: 4.536; 2014 IF: 4.772 |
|
|
Call Number |
UA @ lucian @ c:irua:119085 |
Serial |
3416 |
|
Permanent link to this record |