Home << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 >>
List View
 | 
Citations
 | 
Details
   web
Records
Author Oueslati, S.; Brammertz, G.; Buffiere, M.; ElAnzeery, H.; Touayar, O.; Koeble, C.; Bekaert, J.; Meuris, M.; Poortmans, J.
Title Physical and electrical characterization of high-performance Cu2ZnSnSe4 based thin film solar cells Type A1 Journal article
Year 2015 Publication Thin solid films : an international journal on the science and technology of thin and thick films Abbreviated Journal Thin Solid Films
Volume 582 Issue 582 Pages (up) 224-228
Keywords A1 Journal article; Condensed Matter Theory (CMT)
Abstract We report on the electrical, optical and physical properties of Cu2ZnSnSe4 solar cells using an absorber layer fabricated by selenization of sputtered Cu, Zn and Cu10Sn90 multilayers. A maximum active-area conversion efficiency of 10.4% under AM1.5G was measured with a maximum short circuit current density of 39.7 mA/cm(2), an open circuit voltage of 394 mV and a fill factor of 66.4%. We perform electrical and optical characterization using photoluminescence spectroscopy, external quantum efficiency, current-voltage and admittance versus temperature measurements in order to derive information about possible causes for the low open circuit voltage values observed. The main defects derived from these measurements are strong potential fluctuations in the absorber layer as well as a potential barrier of the order of 133 meV at the back side contact. (C) 2014 Elsevier B.V. All rights reserved.
Address
Corporate Author Thesis
Publisher Place of Publication Lausanne Editor
Language Wos 000352225900048 Publication Date 2014-10-20
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0040-6090 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 1.879 Times cited 49 Open Access
Notes ; We would like to acknowledge Tom De Geyter, Greetje Godiers, and Guido Huyberechts from Flamac in Gent for sputtering of the metal layers. AGC is acknowledged for providing substrates. This research is partially funded by the Flemish government, Department Economy, Science and Innovation. ; Approved Most recent IF: 1.879; 2015 IF: 1.759
Call Number UA @ lucian @ c:irua:132504 Serial 4225
Permanent link to this record
 
 
Author Odin, G.P.; Vanmeert, F.; Farges, F.; Gand, G.; Janssens, K.; Romero-Sarmiento, M.-F.; Steyer, J.S.; Vantelon, D.; Rouchon, V.
Title Alteration of fossil-bearing shale (Autun, France; Permian), part II : monitoring artificial and natural ageing by combined use of S and Ca K-edge XANES analysis, Rock-Eval pyrolysis and FTIR analysis Type A1 Journal article
Year 2015 Publication Annales de paléontologie Abbreviated Journal Ann Paleontol
Volume 101 Issue 3 Pages (up) 225-239
Keywords A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Abstract Fossil-bearing shale specimens that include sulfides in their compositions are chemically reactive and sometimes also mechanically fragile. This decay is often related to iron sulfate efflorescence resulting from the oxidation of sulfide compounds. The processes underlying these degradations are poorly known, thus impeding the elaboration of curative or preventive treatments. The present contribution aims to identify the origin of museum specimen alterations. It focuses on the Flouest collection housed at the Museum National d'Histoire Naturelle (MNHN, Paris, France) and originating from the Autun Basin (Saone-et-Loire, France, Permian). To evaluate the alteration of MNHN specimens, it appeared necessary to compare their composition with that of unaltered shale so as to identify chemical changes occurring during ageing. Therefore, new material was collected in the Autun Basin, among others on the locality of Muse that corresponds to the same lithostratigraphic unit as that of the MNHN specimens. This material was, if necessary, artificially aged. The first part of this work, presented elsewhere, deals with the use of Xray diffraction and Mossbauer spectroscopy for characterizing iron reactivity and speciation. It leads to the conclusion that the reactivity of iron in the shale matrix was limited and could not account for the large efflorescence of iron (II) sulfate occurring nearby the fossil. The second part presented here focuses on the use of S K-edge X-ray Absorption Near Edge Structure (XANES) spectroscopy for characterizing sulfur speciation and reactivity. Measurements were performed on the shale matrix and on thin layers of maceral found in the proximity of damaged areas. As sulfur may be found in association with calcium or organic matter, complementary techniques were implemented, such as FTIR spectroscopy, Rock-Eval pyrolysis (characterization of organic matter content) and Ca K-edge XANES (analysis of calcium speciation) spectroscopy. It was shown that sulfur is mainly related to thioether, sulfoxide, iron sulfide, and sulfates whereas calcium is mainly bound to carboxylate, carbonate and/or sulfate groups. FTIR analysis of the macerals confirmed the presence of vitrinite on damaged MNHN specimens. The low oxygen content of new shale samples determined by Rock-Eval pyrolysis indicates that the organic matter is well preserved, despite the fact that samples come from outcrop surface. In the newly collected material, sulfur is mainly related to organic sulfides (thioether) with a minor occurrence of iron sulfide. In the shale fraction of damaged MNHN specimens, sulfur is mostly oxidized into a mixture of iron and calcium sulfate. However, in the vitrinite layers of the same specimens, a large proportion of sulfur corresponds to organic sulfides. Also the oxidation of sulfur does not occur homogeneously but preferentially in the shale fraction, probably because this latter is porous whereas vitrinite is not. Artificial ageing of new shale material showed that the oxidation of organic sulfides could be reproduced at 90 degrees C, 80% of relative humidity. However, the obtained efflorescence almost exclusively corresponds to calcium sulfate whereas iron (II) sulfates are mostly observed on MNHN specimens. The new material collected on site is probably to be questioned, and future studies will have to select new samples with fossil remains. This will be the object of the third part of this work. (C) 2015 Elsevier Masson SAS. All rights reserved.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000363821700009 Publication Date 2015-05-09
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0753-3969 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 1.113 Times cited 6 Open Access
Notes ; This work was conducted within a PhD work that was supported by a doctoral school grant of the Museum national d'Histoire naturelle, Paris, France. We acknowledge SOLEIL for provision of synchrotron radiation facilities (Proposals ID “20130462” and “20110189”) and we would like to thank Nicolas Trcera, Pierre Lagarde and Anne Marie Flanck for assistance in using beamline LUCIA. ; Approved Most recent IF: 1.113; 2015 IF: 0.970
Call Number UA @ admin @ c:irua:129523 Serial 5462
Permanent link to this record
 
 
Author Guerrero, A.; Pfannmöller, M.; Kovalenko, A.; Ripolles, T.S.; Heidari, H.; Bals, S.; Kaufmann, L.-D.; Bisquert, J.; Garcia-Belmonte, G.
Title Nanoscale mapping by electron energy-loss spectroscopy reveals evolution of organic solar cell contact selectivity Type A1 Journal article
Year 2015 Publication Organic electronics: physics, materials, applications Abbreviated Journal Org Electron
Volume 16 Issue 16 Pages (up) 227-233
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Organic photovoltaic (OPV) devices are on the verge of commercialization being long-term stability a key challenge. Morphology evolution during lifetime has been suggested to be one of the main pathways accounting for performance degradation. There is however a lack of certainty on how specifically the morphology evolution relates to individual electrical parameters on operating devices. In this work a case study is created based on a thermodynamically unstable organic active layer which is monitored over a period of one year under non-accelerated degradation conditions. The morphology evolution is revealed by compositional analysis of ultrathin cross-sections using nanoscale imaging in scanning transmission electron microscopy (STEM) coupled with electron energy-loss spectroscopy (EELS). Additionally, devices are electrically monitored in real-time using the non-destructive electrical techniques capacitance-voltage (C-V) and Impedance Spectroscopy (IS). By comparison of imaging and electrical techniques the relationship between nanoscale morphology and individual electrical parameters of device operation can be conclusively discerned. It is ultimately observed how the change in the cathode contact properties occurring after the migration of fullerene molecules explains the improvement in the overall device performance. (C) 2014 Elsevier B.V. All rights reserved.
Address
Corporate Author Thesis
Publisher Place of Publication London Editor
Language Wos 000345649500029 Publication Date 2014-11-17
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1566-1199; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 3.399 Times cited 24 Open Access OpenAccess
Notes 287594 Sunflower; 335078 Colouratom; ECAS_Sara; (ROMEO:green; preprint:; postprint:can ; pdfversion:cannot); Approved Most recent IF: 3.399; 2015 IF: 3.827
Call Number c:irua:122169 Serial 2267
Permanent link to this record
 
 
Author Sathiya, M.; Abakumov, A.M.; Foix, D.; Rousse, G.; Ramesha, K.; Saubanère, M.; Doublet, M. .; Vezin, H.; Laisa, C.P.; Prakash, A.S.; Gonbeau, D.; Van Tendeloo, G.; Tarascon, J.M.
Title Origin of voltage decay in high-capacity layered oxide electrodes Type A1 Journal article
Year 2015 Publication Nature materials Abbreviated Journal Nat Mater
Volume 14 Issue 14 Pages (up) 230-238
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Although Li-rich layered oxides (Li1+xNiyCozMn1−x−y−zO2 > 250 mAh g−1) are attractive electrode materials providing energy densities more than 15% higher than todays commercial Li-ion cells, they suffer from voltage decay on cycling. To elucidate the origin of this phenomenon, we employ chemical substitution in structurally related Li2RuO3 compounds. Li-rich layered Li2Ru1−yTiyO3 phases with capacities of ~240 mAh g−1 exhibit the characteristic voltage decay on cycling. A combination of transmission electron microscopy and X-ray photoelectron spectroscopy studies reveals that the migration of cations between metal layers and Li layers is an intrinsic feature of the chargedischarge process that increases the trapping of metal ions in interstitial tetrahedral sites. A correlation between these trapped ions and the voltage decay is established by expanding the study to both Li2Ru1−ySnyO3 and Li2RuO3; the slowest decay occurs for the cations with the largest ionic radii. This effect is robust, and the finding provides insights into new chemistry to be explored for developing high-capacity layered electrodes that evade voltage decay.
Address
Corporate Author Thesis
Publisher Place of Publication London Editor
Language Wos 000348600200024 Publication Date 2014-12-01
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1476-1122;1476-4660; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 39.737 Times cited 395 Open Access
Notes 246791 Countatoms; 312483 Esteem2; esteem2_ta Approved Most recent IF: 39.737; 2015 IF: 36.503
Call Number c:irua:132555 c:irua:132555 Serial 2528
Permanent link to this record
 
 
Author Barreca, D.; Carraro, G.; Gasparotto, A.; Maccato, C.; Warwick, M.E.A.; Turner, S.; Van Tendeloo, G.
Title Fabrication and Characterization of Fe2O3-Based Nanostructures Functionalized with Metal Particles and Oxide Overlayers Type A1 Journal article
Year 2015 Publication Journal of advanced microscopy research Abbreviated Journal
Volume 10 Issue 10 Pages (up) 239-243
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract We report on the design of nanosystems based on functionalized -Fe 2 O 3 nanostructures supported on fluorine-doped tin oxide (FTO) substrates. The target materials were developed by means of hybrid vapor phase approaches, combining plasma assisted-chemical vapor deposition (PA-CVD) for the production of iron(III) oxide systems and the subsequent radio frequency (RF)-sputtering or atomic layer deposition (ALD) for the functionalization with Au nanoparticles or TiO 2 overlayers, respectively. The interplay between material characteristics and the adopted processing parameters was investigated by complementary analytical techniques, encompassing X-ray photoelectron spectroscopy (XPS), field emission-scanning electron microscopy (FE-SEM), high angle annular dark field-scanning transmission electron microscopy (HAADF-STEM), and energy dispersive X-ray spectroscopy (EDXS). The obtained results highlight the possibility of fabricating Au/ -Fe 2 O 3 nanocomposites, with a controlled dispersion and distribution of metal particles, and TiO 2 / -Fe 2 O 3 heterostructures, characterized by an intimate coupling between the constituent oxides.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos Publication Date 2015-12-01
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 2156-7573 ISBN Additional Links UA library record
Impact Factor Times cited Open Access
Notes The authors acknowledge the financial support under the FP7 project “SOLARO- GENIX” (NMP4-SL-2012-310333), as well as Padova University ex-60% 2012–2015 projects, grant n CPDR132937/13 (SOLLEONE), and Regione Lombardia- INSTM ATLANTE program. Stuart Turner acknowledges the FWO Flanders for a post-doctoral scholarship. Thanks are also due to Dr. L. Borgese and Prof. E. Bontempi (Chemistry for Technologies Laboratory, Brescia Univer- sity, Italy) for precious assistance in ALD experiments. Approved Most recent IF: NA
Call Number EMAT @ emat @ c:irua:132798 Serial 4058
Permanent link to this record
 
 
Author Cambré, S.; Campo, J.; Beirnaert, C.; Verlackt, C.; Cool, P.; Wenseleers, W.
Title Asymmetric dyes align inside carbon nanotubes to yield a large nonlinear optical response Type A1 Journal article
Year 2015 Publication Nature nanotechnology Abbreviated Journal Nat Nanotechnol
Volume 10 Issue 10 Pages (up) 248-252
Keywords A1 Journal article; Engineering sciences. Technology; Nanostructured and organic optical and electronic materials (NANOrOPT); Laboratory of adsorption and catalysis (LADCA); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Abstract Asymmetric dye molecules have unusual optical and electronic properties1, 2, 3. For instance, they show a strong second-order nonlinear optical (NLO) response that has attracted great interest for potential applications in electro-optic modulators for optical telecommunications and in wavelength conversion of lasers2, 3. However, the strong Coulombic interaction between the large dipole moments of these molecules favours a pairwise antiparallel alignment that cancels out the NLO response when incorporated into bulk materials. Here, we show that by including an elongated dipolar dye (p,p′-dimethylaminonitrostilbene, DANS, a prototypical asymmetric dye with a strong NLO response4) inside single-walled carbon nanotubes (SWCNTs)5, 6, an ideal head-to-tail alignment in which all electric dipoles point in the same sense is naturally created. We have applied this concept to synthesize solution-processible DANS-filled SWCNTs that show an extremely large total dipole moment and static hyperpolarizability (β0 = 9,800 × 10−30 e.s.u.), resulting from the coherent alignment of arrays of ∼70 DANS molecules.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000350799700016 Publication Date 2015-02-02
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1748-3387;1748-3395; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 38.986 Times cited 46 Open Access
Notes Approved Most recent IF: 38.986; 2015 IF: 34.048
Call Number c:irua:125405 Serial 158
Permanent link to this record
 
 
Author Adam, N.; Leroux, F.; Knapen, D.; Bals, S.; Blust, R.
Title The uptake and elimination of ZnO and CuO nanoparticles in Daphnia magna under chronic exposure scenarios Type A1 Journal article
Year 2015 Publication Water research Abbreviated Journal Water Res
Volume 68 Issue 68 Pages (up) 249-261
Keywords A1 Journal article; Electron microscopy for materials research (EMAT); Veterinary physiology and biochemistry
Abstract In this study, the uptake and elimination of ZnO and CuO nanoparticles in Daphnia magna was tested. Daphnids were exposed during 10 days to sublethal concentrations of ZnO and CuO nanoparticles and corresponding metal salts (ZnCl2 and CuCl2.2H2O), after which they were transferred to unexposed medium for another 10 days. At different times during the exposure and none-exposure, the total and internal zinc or copper concentration of the daphnids was determined and the nanoparticles were localized in the organism using electron microscopy. The exposure concentrations were characterized by measuring the dissolved, nanoparticle and aggregated fraction in the medium. The results showed that the ZnO nanoparticles quickly dissolved after addition to the medium. Contrarily, only a small fraction (corresponding to the dissolved metal salt) of the CuO nanoparticles dissolved, while most of these nanoparticles formed large aggregates. Despite an initial increase in zinc and copper concentration during the first 48 hour to 5 day exposure, the body concentration reached a plateau level that was comparable for the ZnO nanoparticles and ZnCl2, but much higher for the CuO nanoparticles (with visible aggregates accumulating in the gut) than CuCl2.2H2O. During the remaining exposure and subsequent none-exposure phase, the zinc and copper concentration decreased fast to concentrations comparable with the unexposed daphnids. The results indicate that D. magna can regulate its internal zinc and copper concentration after exposure to ZnO and CuO nanoparticles, similar as after exposure to metal salts. The combined dissolution, accumulation and toxicity results confirm that the toxicity of ZnO and CuO nanoparticles is caused by the dissolved fraction. Keywords nano; zinc; copper; dissolution; aggregation; electron microscopy
Address
Corporate Author Thesis
Publisher Place of Publication Oxford Editor
Language Wos 000347756900022 Publication Date 2014-10-14
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0043-1354; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 6.942 Times cited 51 Open Access OpenAccess
Notes ; The authors would like to thank Valentine Mubiana and Steven Joosen (Sphere, UA) for performing the ICP-MS and ICP-OES measurements and Prof. Dr. Gustaaf Van Tendeloo for making the collaboration between the EMAT and Sphere group possible. This study is part of the ENNSATOX-project, which was funded by the EU (NMP4-SL-2009-229244). The authors report no conflicts of interest. ; Approved Most recent IF: 6.942; 2015 IF: 5.528
Call Number c:irua:119366 c:irua:119366 Serial 3822
Permanent link to this record
 
 
Author Ayalew, E.; Gebre, Y.; De Wael, K.
Title A survey of occupational exposure to inhalable wood dust among workers in small- and medium-scale wood-processing enterprises in Ethiopia Type A1 Journal article
Year 2015 Publication The annals of occupational hygiene Abbreviated Journal Ann Occup Hyg
Volume 59 Issue 2 Pages (up) 253-257
Keywords A1 Journal article; Pharmacology. Therapy; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Abstract A study of wood dust exposure in 20 small- and medium-scale wood-processing enterprises was performed in Ethiopia. Sampling was conducted daily from January to June, 2013 and a total of 360 samples from 113 workers were collected with Institute of Occupational Medicine (IOM) personal samplers. Eight-hour time-weighted average exposure to wood dust ranged from 0.24 to 23.3mg m−3 with a geometric mean (GM) of 6.82mg m−3 and a geometric standard deviation of 1.82. Although Ethiopia did not have any defined standard of Occupational Exposure Limit for wood dust exposure, 71% of the measurements exceeded the limit of 5mg m−3 set by the European Union (EU). Higher than the EU exposure limit was measured while workers perform sanding and sawing activities with a GM of 9.72 and 7.60mg m−3, respectively. In conclusion, wood workers in the small- and medium-scale enterprises are at a higher risk of developing different respiratory health problems with continuous exposure trends.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000352158700011 Publication Date 2014-10-28
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0003-4878 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 1.71 Times cited 4 Open Access
Notes ; Eyasu Ayalew thanks the Addis Ababa University (Center for Environmental Sciences) for the personal grant for independent study. ; Approved Most recent IF: 1.71; 2015 IF: 2.101
Call Number UA @ admin @ c:irua:119739 Serial 5857
Permanent link to this record
 
 
Author Sahin, H.; Leenaerts, O.; Singh, S.K.; Peeters, F.M.
Title Graphane Type A1 Journal article
Year 2015 Publication Wiley Interdisciplinary Reviews: Computational Molecular Science Abbreviated Journal Wires Comput Mol Sci
Volume 5 Issue 5 Pages (up) 255-272
Keywords A1 Journal article; Condensed Matter Theory (CMT)
Abstract Atomically thin crystals have recently been the focus of attention, in particular, after the synthesis of graphene, a monolayer hexagonal crystal structure of carbon. In this novel material class, the chemically derived graphenes have attracted tremendous interest. It was shown that, although bulk graphite is a chemically inert material, the surface of single layer graphene is rather reactive against individual atoms. So far, synthesis of several graphene derivatives have been reported such as hydrogenated graphene graphane' (CH), fluorographene (CF), and chlorographene (CCl). Moreover, the stability of bromine and iodine covered graphene were predicted using computational tools. Among these derivatives, easy synthesis, insulating electronic behavior and reversibly tunable crystal structure of graphane make this material special for future ultra-thin device applications. This overview surveys structural, electronic, magnetic, vibrational, and mechanical properties of graphane. We also present a detailed overview of research efforts devoted to the computational modeling of graphane and its derivatives. Furthermore recent progress in synthesis techniques and possible applications of graphane are reviewed as well. WIREs Comput Mol Sci 2015, 5:255-272. doi: 10.1002/wcms.1216 For further resources related to this article, please visit the . Conflict of interest: The authors have declared no conflicts of interest for this article.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000352862700001 Publication Date 2015-03-12
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1759-0876; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 14.016 Times cited 54 Open Access
Notes ; This work was supported by the Flemish Science Foundation (FWO-Vl) and the Methusalem foundation of the Flemish government. H. Sahin is supported by a FWO Pegasus Long Marie Curie Fellowship. ; Approved Most recent IF: 14.016; 2015 IF: 11.885
Call Number c:irua:125996 Serial 1366
Permanent link to this record
 
 
Author Paolella, A.; Bertoni, G.; Hovington, P.; Feng, Z.; Flacau, R.; Prato, M.; Colombo, M.; Marras, S.; Manna, L.; Turner, S.; Van Tendeloo, G.; Guerfi, A.; Demopoulos, G.P.; Zaghib, K.;
Title Cation exchange mediated elimination of the Fe-antisites in the hydrothermal synthesis of LiFePO4 Type A1 Journal article
Year 2015 Publication Nano energy Abbreviated Journal Nano Energy
Volume 16 Issue 16 Pages (up) 256-267
Keywords A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Abstract In this work we elucidate the elimination of mechanism Fe-antisite defects in lithium iron phosphate (LiFePO4) during the hydrothermal synthesis. Compelling evidence of this effect is provided by combining Neutron Powder Diffraction (NPD), High Resolution (Scanning) Transmission Electron Microscopy (HR-(S)TEM), Electron Energy Loss Spectroscopy (EELS), X-Ray Photoelectron Spectroscopy (XPS) and calculations. We found: i) the first intermediate vivianite inevitably creates Fe-antisite defects in LiFePO4; ii) the removal of these antisite defects by cation exchange is assisted by a nanometer-thick amorphous layer, rich in Li, that enwraps the LiFePO4 crystals.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000364579300027 Publication Date 2015-06-19
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 2211-2855; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 12.343 Times cited 27 Open Access
Notes The authorswanttoacknowledgeVincentGariepy,Cathe- rine Gagnon,JulieTrottier,DanielClement,Dr.CyrilFaure of IREQ,Dr.GaiaTomaselloofInstitutfürTheoretische PhysikFreieUniversitätBerlinandProf.MichelArmandof CICenergigune forhelpfuldiscussionsandtechnical supports. Approved Most recent IF: 12.343; 2015 IF: 10.325
Call Number c:irua:127688 Serial 296
Permanent link to this record
 
 
Author Danthurebandara, M.; Van Passel, S.; Machiels, L.; Van Acker, K.
Title Valorization of thermal treatment residues in enhanced landfill mining : environmental and economic evaluation Type A1 Journal article
Year 2015 Publication Journal Of Cleaner Production Abbreviated Journal J Clean Prod
Volume 99 Issue Pages (up) 275-285
Keywords A1 Journal article; Economics; Engineering sciences. Technology; Engineering Management (ENM)
Abstract Enhanced Landfill Mining is an innovative concept which allows the recovery of land, re-introduction of materials to the material cycles and recovery of energy from a considerably large stock of resources held in landfills. Plasma gasification is a viable candidate for combined energy and material valorization in the framework of Enhanced landfill Mining. Besides energy production, plasma gasification also delivers an environmentally stable vitrified residue called plasmastone, which can be converted into building materials. This paper presents an environmental and economic evaluation of the valorization of thermal treatment residues (plasmastone) in the context of Enhanced Landfill Mining. The most common valorization route, that is, the treatment of plasmastone via production of aggregates, is compared with two other possible, higher added value applications, which are inorganic polymer production and blended cement production. The evaluation is based on life cycle assessment and life cycle costing. The study suggests that the environmental and economic performances of the valorization routes depend mainly on the quality and quantity of the final products produced from a certain amount of plasmastone. The materials with the greatest contribution to potential global warming and to the net present value of the valorization scenarios are the process input materials of sodium silicate, sodium hydroxide and cement. The study concludes that the plasmastone valorization via inorganic polymer production yields higher environmental benefits, while the blended cement production provides higher economic profits. Plasmastone valorization via aggregates production does not yield economic or environmental benefits. Given the trade-off between environmental and economic performances, we conclude that the decisions regarding the selection of appropriate valorization routes should be made cautiously to obtain optimal environmental benefits and economic profits. (C) 2015 Elsevier Ltd. All rights reserved.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000356195000023 Publication Date 2015-03-14
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0959-6526 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 5.715 Times cited 17 Open Access
Notes ; The authors would like to acknowledge the funding of this study by the IWT-O&O ELFM project 'Closing the Circle & Enhanced Landfill Mining as part of the Transition to Sustainable Materials Management' and the valuable discussions with Group Machiels (Belgium). ; Approved Most recent IF: 5.715; 2015 IF: 3.844
Call Number UA @ admin @ c:irua:127533 Serial 6276
Permanent link to this record
 
 
Author Chemchuen, S.; Zhou, K.; Kabir, N.A.; Chen, Y.; Ke, X.; Van Tendeloo, G.; Verpoort, F.
Title Tuning metal sites of DABCO MOF for gas purification at ambient conditions Type A1 Journal article
Year 2015 Publication Microporous and mesoporous materials: zeolites, clays, carbons and related materials Abbreviated Journal Micropor Mesopor Mat
Volume 201 Issue 201 Pages (up) 277-285
Keywords A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Abstract Metalorganic frameworks (MOFs) have emerged as new porous materials for capture and separation of binary gas mixtures. Tuning the metal sites in MOF structures has an impact on properties, which enhance affinity of gas adsorption and selectivity (e.g., surface area, cavity, electric field, etc.). The synthesis and characterization of a M-DABCO series (M = Ni, Co, Cu, Zn) of MOFs are described in this study. The experiments were conducted using multicomponent gas mixtures and the Ideal Adsorbed Solution Theory (IAST) was applied to determine the CO2/CH4 selectivity. Experimental adsorption isotherms were fitted with a model equation to evaluate the characteristic adsorption energy (Isosteric, Qst) of this series. The Ni metal in the M-DABCO series reveals the best performance concerning CO2 adsorption and CH4/CO2 selectivity at ambient conditions based on IAST calculations. The combination of characterizations, calculations and adsorption experiments were used to discuss the metal impact on the adsorption sites in the M-DABCO series at ambient conditions.
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos 000345185200030 Publication Date 2014-09-20
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1387-1811; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 3.615 Times cited 38 Open Access
Notes 246791-Countatoms Approved Most recent IF: 3.615; 2015 IF: 3.453
Call Number c:irua:120473 Serial 3748
Permanent link to this record
 
 
Author van der Stam, W.; Akkerman, Q.A.; Ke, X.; van Huis, M.A.; Bals, S.; de Donega, C.M.
Title Solution-processable ultrathin size- and shape-controlled colloidal Cu2-xS nanosheets Type A1 Journal article
Year 2015 Publication Chemistry of materials Abbreviated Journal Chem Mater
Volume 27 Issue 27 Pages (up) 283-291
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Ultrathin two-dimensional (2D) nanosheets (NSs) possess extraordinary properties that are attractive for both fundamental studies and technological devices. Solution-based bottom-up methods are emerging as promising routes to produce free-standing NSs, but the synthesis of colloidal NSs with well-defined size and shape has remained a major challenge. In this work, we report a novel method that yields 2 nm thick colloidal Cu2-xS NSs with well-defined shape (triangular or hexagonal) and size (100 nm to 3 mu m). The key feature of our approach is the use of a synergistic interaction between halides (Br or Cl) and copper-thiolate metal-organic frameworks to create a template that imposes 2D constraints on the Cu-catalyzed C-S thermolysis, resulting in nucleation and growth of colloidal 2D Cu2-xS NSs. Moreover, the NS composition can be postsynthetically tailored by exploiting topotactic cation exchange reactions. This is illustrated by converting the Cu2-xS NSs into ZnS and CdS NSs while preserving their size and shape. The method presented here thus holds great promise as a route to solution-processable compositionally diverse ultrathin colloidal NSs with well-defined shape and size.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000348085300036 Publication Date 2014-12-04
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0897-4756;1520-5002; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 9.466 Times cited 68 Open Access OpenAccess
Notes 335078 Colouratom; 246791 Countatoms; 312483 Esteem2; esteem2ta; ECASSara; (ROMEO:white; preprint:; postprint:restricted 12 months embargo; pdfversion:cannot); Approved Most recent IF: 9.466; 2015 IF: 8.354
Call Number c:irua:123865 c:irua:123865 Serial 3052
Permanent link to this record
 
 
Author Berdiyorov, G.R.; Savel'ev, S.; Kusmartsev, F.V.; Peeters, F.M.
Title Effect of ordered array of magnetic dots on the dynamics of Josephson vortices in stacked SNS Josephson junctions under DC and AC current Type A1 Journal article
Year 2015 Publication European physical journal : B : condensed matter and complex systems Abbreviated Journal Eur Phys J B
Volume 88 Issue 88 Pages (up) 286
Keywords A1 Journal article; Condensed Matter Theory (CMT)
Abstract We use the anisotropic time-dependent Ginzburg-Landau theory to investigate the effect of a square array of out-of-plane magnetic dots on the dynamics of Josephson vortices (fluxons) in artificial stacks of superconducting-normal-superconducting (SNS) Josephson junctions in the presence of external DC and AC currents. Periodic pinning due to the magnetic dots distorts the triangular lattice of fluxons and results in the appearance of commensurability features in the current-voltage characteristics of the system. For the larger values of the magnetization, additional peaks appear in the voltage-time characteristics of the system due to the creation and annihilation of vortex-antivortex pairs. Peculiar changes in the response of the system to the applied current is found resulting in a “superradiant” vortex-flow state at large current values, where a rectangular lattice of moving vortices is formed. Synchronizing the motion of fluxons by adding a small ac component to the biasing dc current is realized. However, we found that synchronization becomes difficult for large magnetization of the dots due to the formation of vortex-antivortex pairs.
Address
Corporate Author Thesis
Publisher Place of Publication Berlin Editor
Language Wos 000363960900002 Publication Date 2015-10-30
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1434-6028 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 1.461 Times cited 1 Open Access
Notes ; This work was supported by EU Marie Curie (Project No. 253057). ; Approved Most recent IF: 1.461; 2015 IF: 1.345
Call Number UA @ lucian @ c:irua:129509 Serial 4166
Permanent link to this record
 
 
Author Vagin, M.Y.; Trashin, S.A.; Beloglazkina, E.K.; Majouga, A.G.
Title Direct reagentless detection of the affinity binding of recombinant His-tagged firefly luciferase with a nickel-modified gold electrode Type A1 Journal article
Year 2015 Publication Mendeleev communications Abbreviated Journal
Volume 25 Issue 4 Pages (up) 290-292
Keywords A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Abstract The direct reagentless electrochemical detection of recombinant firefly luciferase binding with a gold electrode modified with nickel complex of 1,16-di[4-(2,6-dihydroxycarbonyl)pyridyl]-1,16-dioxa-8,9-dithiahexadecane has been carried out.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000360416600021 Publication Date 2015-08-07
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0959-9436 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor Times cited Open Access
Notes Approved no
Call Number UA @ admin @ c:irua:127814 Serial 7811
Permanent link to this record
 
 
Author Benito, P.; Nuyts, G.; Monti, M.; de Nolf, W.; Fornasari, G.; Janssens, K.; Scavetta, E.; Vaccari, A.
Title Stable Rh particles in hydrotalcite-derived catalysts coated on FeCrAlloy foams by electrosynthesis Type A1 Journal article
Year 2015 Publication Applied catalysis : B : environmental Abbreviated Journal Appl Catal B-Environ
Volume 179 Issue Pages (up) 321-332
Keywords A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Abstract Rh-based structured catalysts for the Catalytic Partial Oxidation of CH4 to syngas were prepared by electrosynthesis of Rh/Mg/Al hydrotalcite-type compounds on FeCrAlloy foams and calcination. The effects of Rh content, total metal concentration, and partial replacement of Mg2+ by Ni2+ in the electrolytic solution on coating thickness, Rh speciation, metallic particle size, and catalytic activity were investigated by SEM/EDS, mu-XRF/XANES and tests under diluted and concentrated reaction conditions. The amount of Rh species, present as Mg (RhxAl1-x)(2)O-4, depended on the thickness of the electrosynthesised layer as well as the Rh particle size and dispersion. Smaller and more dispersed particles were obtained by decreasing the Rh concentration in the electrolytic solution from Rh/Mg/Al=11/70/19 to 5/70/25 and 2/70/28 atomic ratio% (a.r.%) and in thinner rather than thicker layers. Despite the improvement in metallic particles features, the CH4 conversion was negatively affected by the low amount of active sites in the coating, the high metal support interaction and possibly the oxidation of metallic particles and carbon formation. A larger amount of solid containing well dispersed Rh particles was deposited by increasing the total metal concentration from 0.03 M to 0.06 M with the Rh/Mg/Al=5/70/25 a.r.%, and the catalytic performances were enhanced. The partial replacement of Mg2+ by Ni2+ gave rise to a very active bimetallic Rh/Ni catalyst, CH4 conversion and selectivity to syngas were above 90%, however, it slightly deactivated with time-on-stream. (C) 2015 Elsevier B.V. All rights reserved.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000359873800036 Publication Date 2015-05-19
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0926-3373 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 9.446 Times cited 14 Open Access
Notes ; The Authors acknowledge M. Salome for helping during the mu XRF/XANES experiments at ID21 Beamline of the ESRF, the Department of Structural Characterisation of CNR-IMM of Bologna for the access to the FEG-SEM facility and Dr F. Ospitali for the scientific support. Thanks are due to Farrel Lytle database for providing the necessary Rh metal spectrum (rhfoil.a99 in http:// ixs.iit.edu/data/FarrelLytledata/). The financial support from the Ministero per l'Istruzione, l'Universita e la Ricerca (MIUR, Roma, Italy) and the University of Bologna (FARB program) is gratefully acknowledged. ; Approved Most recent IF: 9.446; 2015 IF: 7.435
Call Number UA @ admin @ c:irua:127777 Serial 5846
Permanent link to this record
 
 
Author Roditchev, D.; Brun, C.; Serrier-Garcia, L.; Cuevas, J.C.; Bessa, V.H.L.; Milošević, M.V.; Debontridder, F.; Stolyarov, V.; Cren, T.
Title Direct observation of Josephson vortex cores Type A1 Journal article
Year 2015 Publication Nature physics Abbreviated Journal Nat Phys
Volume 11 Issue 11 Pages (up) 332-337
Keywords A1 Journal article; Condensed Matter Theory (CMT)
Abstract Superconducting correlations may propagate between two superconductors separated by a tiny insulating or metallic barrier, allowing a dissipationless electric current to flow(1,2). In the presence of a magnetic field, the maximum supercurrent oscillates(3) and each oscillation corresponding to the entry of one Josephson vortex into the barrier(4). Josephson vortices are conceptual blocks of advanced quantum devices such as coherent terahertz generators(5) or qubits for quantum computing(6), in which on-demand generation and control is crucial. Here, we map superconducting correlations inside proximity Josephson junctions(7) using scanning tunnelling microscopy. Unexpectedly, we find that such Josephson vortices have real cores, in which the proximity gap is locally suppressed and the normal state recovered. By following the Josephson vortex formation and evolution we demonstrate that they originate from quantum interference of Andreev quasiparticles(8), and that the phase portraits of the two superconducting quantum condensates at edges of the junction decide their generation, shape, spatial extent and arrangement. Our observation opens a pathway towards the generation and control of Josephson vortices by applying supercurrents through the superconducting leads of the junctions, that is, by purely electrical means without any need for a magnetic field, which is a crucial step towards high-density on-chip integration of superconducting quantum devices.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000352163100016 Publication Date 2015-02-23
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1745-2473;1745-2481; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 22.806 Times cited 102 Open Access
Notes T.C., C.B., F.D., V.S. and D.R. acknowledge financial support from the French ANR project and the French-Russian program PICS-CNRS/RAS. The authors also thank V. Cherkez for assistance during experiments and V. Vinokur (Argonne National Laboratory, Illinois USA) and A. Buzdin (University of Bordeaux 1, France) for stimulating discussions. J.C.C. acknowledges financial support from the Spanish MICINN (Contract No. FIS2011-28851-C1). V.H.L.B. acknowledges support from CNPq Brazil and productive discussions with Prof. A. Chaves (UFC, Brazil). M.V.M. acknowledges support from Research Foundation Flanders (FWO-Vlaanderen) and CAPES Brazil (PVE project BEX1392/11-5). Approved Most recent IF: 22.806; 2015 IF: 20.147
Call Number c:irua:132524 c:irua:132524 Serial 3943
Permanent link to this record
 
 
Author Kuppens, T.; Van Dael, M.; Vanreppelen, K.; Thewys, T.; Yperman, J.; Carleer, R.; Schreurs, S.; Van Passel, S.
Title Techno-economic assessment of fast pyrolysis for the valorization of short rotation coppice cultivated for phytoextraction Type A1 Journal article
Year 2015 Publication Journal Of Cleaner Production Abbreviated Journal J Clean Prod
Volume 88 Issue Pages (up) 336-344
Keywords A1 Journal article; Engineering Management (ENM)
Abstract The main barrier in the commercialization of phytoextraction as a sustainable alternative for remediating metal contaminated soils is its long time period, which can be countered by biomass valorization. From an environmental point of view, fast pyrolysis of the biomass is promising because its lower process temperature prevents metal volatilization. The remaining question is whether fast pyrolysis is also preferred from an economic point of view. Therefore, a techno-economic assessment of fast pyrolysis has been performed for a case study in the Campine region in Belgium. For this region, willow trees cultivated in short rotation have the right characteristics to serve as a phytoextracting crop. A techno-economic assessment requires by definition a multidisciplinary approach. The problem statement urges for a focus on the economic profitability from the viewpoint of an investor, including economic risk analysis. Fast pyrolysis seems more profitable than gasification. The profit is dependent on the scale of operation, the policy support (subsidies) and the oil yield. The economic risk can be reduced by increasing the scale of operation by means of complementing feedstocks, and by valorization of the char byproduct by subsequent processing to activated carbon. (C) 2014 Elsevier Ltd. All rights reserved.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000347771100036 Publication Date 2014-07-19
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0959-6526 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 5.715 Times cited 36 Open Access
Notes ; ; Approved Most recent IF: 5.715; 2015 IF: 3.844
Call Number UA @ admin @ c:irua:127539 Serial 6264
Permanent link to this record
 
 
Author Silva, A.L.M.; Carvalho, M.L.; Janssens, K.; Veloso, J.F.C.A.
Title A large area full-field EDXRF imaging system based on a THCOBRA gaseous detector Type A1 Journal article
Year 2015 Publication Journal of analytical atomic spectrometry Abbreviated Journal J Anal Atom Spectrom
Volume 30 Issue 2 Pages (up) 343-352
Keywords A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Abstract By taking advantage of the attractive features in terms of gain, position and energy resolution of the 2D-THCOBRA detector, a new large area Full-Field X-ray Fluorescence Imaging (FF-XRFI) system for EDXRF imaging applications was developed. The proposed FF-XRFI system has an active area of 10 x 10 cm(2) and can be used to examine macroscopic samples with a moderately good energy resolution (< 1.6 keV FWHM at 8 keV) and a suitable spatial resolution (similar to 500 mu m FWHM). This combination of characteristics allows us to record elemental distribution maps from the surface of different sample types by combining image and energy information. Two different approaches were used for X-ray optics, one based on a single pinhole and another based on a parallel multiple-hole collimator. To illustrate the system capabilities, some sample examples were imaged and studied.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000349145700003 Publication Date 2014-10-24
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0267-9477 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 3.379 Times cited 11 Open Access
Notes ; The authors thank Stijn Legrand for acquisition of the MAXRF maps shown in Fig. 15. This work was partially supported by projects CERN/FP/123604/2011 FEDER, COMPETE and FCT (Lisbon) programs. A. L. M. Silva is supported by the QREN programme Mais Centro – Programa Operacional Regional do Centro, FEDER and COMPETE, through the project Biomaterials for Regenerative Medicine (CENTRO-07-ST24-FEDER-002030). ; Approved Most recent IF: 3.379; 2015 IF: 3.466
Call Number UA @ admin @ c:irua:125297 Serial 5452
Permanent link to this record
 
 
Author Anaf, W.; Bencs, L.; Van Grieken, R.; Janssens, K.; De Wael, K.
Title Indoor particulate matter in four Belgian heritage sites : case studies on the deposition of dark-colored and hygroscopic particles Type A1 Journal article
Year 2015 Publication The science of the total environment Abbreviated Journal Sci Total Environ
Volume 506 Issue Pages (up) 361-368
Keywords A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Abstract Atmospheric total suspended particulate (TSP) was passively sampled by means of deployed horizontal and vertical filters in various rooms of four Belgian cultural heritage buildings, installed with various heating/ventilation systems. Soiling/blackening and deposition of inorganic, water-soluble aerosol components were considered. The extent of soiling was determined by means of two independent methods: (1) in terms of the covering rate of the samplers by optical reflection microscopy and (2) the reduction in lightness of the samplers using the CIE L*a*b* color space by spectrophotometry. A fairly good correlation was found between both methods. The inorganic composition of the deposited water-soluble TSP was quantified by means of ion chromatography. Compared to controlled environments, uncontrolled environments showed increased water-soluble aerosol content of the total deposited mass. Higher chloride deposition was observed on horizontal surfaces, compared to vertical surfaces.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000347576800039 Publication Date 2014-11-24
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0048-9697 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 4.9 Times cited 12 Open Access
Notes ; ; Approved Most recent IF: 4.9; 2015 IF: 4.099
Call Number UA @ admin @ c:irua:120640 Serial 5662
Permanent link to this record
 
 
Author Liao, L.; Heylen, S.; Vallaey, B.; Keulemans, M.; Lenaerts, S.; Roeffaers, M.B.J.; Martens, J.A.
Title Photocatalytic carbon oxidation with nitric oxide Type A1 Journal article
Year 2015 Publication Applied catalysis : B : environmental Abbreviated Journal Appl Catal B-Environ
Volume 166 Issue Pages (up) 374-380
Keywords A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Abstract The photocatalytic oxidation of carbon black on TiO2 using nitric oxide as an oxidizing agent was investigated. Layer-wise deposited carbon and TiO2 powder was illuminated with UVA light in the presence of NO at parts per million concentrations in dry and hydrated carrier gas at a temperature of 150 degrees C. Carbon was photocatalytically converted mainly into CO2, and NO mainly into N-2. Carbon oxidation rates of 7.2 mu g/h/mgTiO(2) were achieved in the presence of 3000 ppm NO. Under these experimental conditions in the absence of molecular oxygen, formation of surface nitrates causing TiO2 photocatalyst deactivation is suppressed. Addition of water enhances surface nitrate formation and catalyst deactivation. NO and carbon particulate matter are air pollutants emitted by diesel engines. Elimination of soot collected on a diesel particulate filter through oxidation is a demanding reaction requiring temperatures in excess of 250 degrees C. The present study opens perspectives for a low-temperature regeneration strategy for the diesel particulate filter that simultaneously performs DeNO(x) reactions. (C) 2014 Elsevier B.V. All rights reserved.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000348753400042 Publication Date 2014-12-03
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0926-3373 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 9.446 Times cited 5 Open Access
Notes ; This work was supported by long-term structural funding by the Flemish government (Methusalem). ; Approved Most recent IF: 9.446; 2015 IF: 7.435
Call Number UA @ admin @ c:irua:123858 Serial 5977
Permanent link to this record
 
 
Author Gjorgievska, E.; Van Tendeloo, G.; Nicholson, J.W.; Coleman, N.J.; Slipper, I.J.; Booth, S.
Title The incorporation of nanoparticles into conventional glass-ionomer dental restorative cements Type A1 Journal article
Year 2015 Publication Microscopy and microanalysis Abbreviated Journal Microsc Microanal
Volume 21 Issue 21 Pages (up) 392-406
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Conventional glass-ionomer cements (GICs) are popular restorative materials, but their use is limited by their relatively low mechanical strength. This paper reports an attempt to improve these materials by incorporation of 10 wt% of three different types of nanoparticles, aluminum oxide, zirconium oxide, and titanium dioxide, into two commercial GICs (ChemFil((R)) Rock and EQUIA (TM) Fil). The results indicate that the nanoparticles readily dispersed into the cement matrix by hand mixing and reduced the porosity of set cements by filling the empty spaces between the glass particles. Both cements showed no significant difference in compressive strength with added alumina, and ChemFil((R)) Rock also showed no significant difference with zirconia. By contrast, ChemFil((R)) Rock showed significantly higher compressive strength with added titania, and EQUIA (TM) Fil showed significantly higher compressive strength with both zirconia and titania. Fewer air voids were observed in all nanoparticle-containing cements and this, in turn, reduced the development of cracks within the matrix of the cements. These changes in microstructure provide a likely reason for the observed increases in compressive strength, and overall the addition of nanoparticles appears to be a promising strategy for improving the physical properties of GICs.
Address
Corporate Author Thesis
Publisher Place of Publication Cambridge, Mass. Editor
Language Wos 000353514700014 Publication Date 2015-02-18
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1431-9276 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 1.891 Times cited 15 Open Access
Notes Approved Most recent IF: 1.891; 2015 IF: 1.877
Call Number UA @ lucian @ c:irua:132523 Serial 4194
Permanent link to this record
 
 
Author Papageorgiou, D.G.; Filippousi, M.; Pavlidou, E.; Chrissafis, K.; Van Tendeloo, G.; Bikiaris, D.
Title Effect of clay modification on structureproperty relationships and thermal degradation kinetics of \beta-polypropylene/clay composite materials Type A1 Journal article
Year 2015 Publication Journal of thermal analysis and calorimetry Abbreviated Journal J Therm Anal Calorim
Volume 122 Issue 122 Pages (up) 393-406
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract The influence of neat and organically modified montmorillonite on the structureproperty relationships of a β-nucleated polypropylene matrix has been thoroughly investigated. High-angle annular dark field scanning transmission electron microscopy revealed that the organic modification of clay facilitated the dispersion of the clay, while X-ray diffractograms showed the α-nucleating effect of the clays on the β-nucleated matrix. The results from tensile tests showed that the organic modification of MMT affected profoundly only the tensile strength at yield and at break. The effect of the organic modification of the clay on the thermal stability of the composites was finally evaluated by thermogravimetric analysis, where the samples filled with oMMT decomposed faster than the ones filled with neat MMT, due to the decomposition of the organic salts that were initially used for the modification of MMT. A kinetics study of the thermal degradation of the composites was also performed, in order to export additional conclusions on the activation energy of the samples.
Address
Corporate Author Thesis
Publisher Place of Publication S.l. Editor
Language Wos 000361431200042 Publication Date 2015-04-29
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1388-6150;1588-2926; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 1.953 Times cited 7 Open Access
Notes 262348 Esmi Approved Most recent IF: 1.953; 2015 IF: 2.042
Call Number c:irua:127492 Serial 805
Permanent link to this record
 
 
Author Anaf, W.; Schalm, O.; Janssens, K.; De Wael, K.
Title Understanding the (in)stability of semiconductor pigments by a thermodynamic approach Type A1 Journal article
Year 2015 Publication Dyes and pigments Abbreviated Journal Dyes Pigments
Volume 113 Issue Pages (up) 409-415
Keywords A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Antwerp Cultural Heritage Sciences (ARCHES)
Abstract Several artists pigments are semiconductors. Some of these materials appear stable over time, whereas others already show remarkable signs of degradation after limited time periods. The (in)stability of these pigments can be understood using a thermodynamic approach. For several pigment-related materials, the thermodynamic oxidation and reduction potential (ϕox and ϕred) were determined and evaluated considering the absolute energy positions of the valence and conduction band edges and the water redox potentials. The positions of ϕox and ϕred can be used in a fast screening of the stability of semiconductor pigments towards photoinduced corrosion in an aqueous/humid environment. This theoretical approach corresponds well with experimental data on pigment permanence and degradation phenomena found in literature.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000346543200052 Publication Date 2014-09-16
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0143-7208 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 3.473 Times cited 14 Open Access
Notes ; The authors acknowledge the funding from the Belspo S2-ART project (Belgian Federal Government) SD/RI/04A. ; Approved Most recent IF: 3.473; 2015 IF: 3.966
Call Number UA @ admin @ c:irua:118875 Serial 5885
Permanent link to this record
 
 
Author Silva, F.S.; Godoi, R.H.M.; Tauler, R.; de André, P.A.; Saldiva, P.H.N.; Van Grieken, R.; de Marchi, M.R.R.
Title Elemental composition of PM2.5 in Araraquara City (Southeast Brazil) during seasons with and without sugar cane burning Type A2 Journal article
Year 2015 Publication Journal of environmental protection Abbreviated Journal
Volume 6 Issue 5 Pages (up) 426-434
Keywords A2 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Abstract Particulate matter with an aerodynamic diameter below 2.5 μm (PM2.5), present in polluted air, has been associated with a large spectrum of health impairments, mainly because of its deep deposition into the lungs. Araraquara City (Southeast Brazil) is surrounded by sugar-cane plantations, which are burned to facilitate the harvesting; this process causes environmental pollution due to the large amounts of soot that are released into the atmosphere. In this work, the elemental composition of PM2.5 was studied in two scenarios, namely in sugar-cane harvesting (HV) and in non-harvesting (NHV) seasons. The sampling strategy included one campaign in each season. PM2.5 was collected using a dichotomous sampler (10 L·min-1, 24 h) with PTFE filters. Information concerning the bulk elemental concentration was provided by energy-dispersive X-ray fluorescence. Enrichment factor analysis indicated that S, Cl, K, Cr, Ni, Cu, Zn, As, Cd and Pb were highly enriched relative to their crustal ratios (to Al). Principal component analysis was used to get some insight about the sources of the elements. Principal component 1 (PC1) explained 30.5% of data variance. The elements that had high loading (>0.7) were: S, Cr, As, and Pb; these are associated with combustion of fossil fuels. In principal component 2 (PC2), Cl, Cu, Zn, and Cd showed high loadings; these elements are associated with biomass burning. The Ni concentration found is three times larger than the threshold of risk for lung cancer, as recommended by the World Health Organization.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos Publication Date 2015-05-04
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 2152-2197 ISBN Additional Links UA library record
Impact Factor Times cited Open Access
Notes Approved no
Call Number UA @ admin @ c:irua:125885 Serial 7891
Permanent link to this record
 
 
Author Romero-Pastor, J.; Garcia-Porras, A.; Van Grieken, R.; Potgieter-Vermaak, S.; Coll-Conesa, J.; Cardell, C.
Title New insights in technology characterization of medieval Valencia glazes Type A1 Journal article
Year 2015 Publication X-ray spectrometry Abbreviated Journal
Volume 44 Issue 6 Pages (up) 426-435
Keywords A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Abstract This study shows the first Raman microscopy (RM) and scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDX) characterization of two 14th and 15th century lead-glazed and luster ceramics from the Manises and Paterna workshops (Valencia, Spain) produced after the Aragon Christian conquest of the Iberian Peninsula (14th century). According to experts, these coetaneous ceramics were most probably involved in a process of technological transfer from the Islamic area of Southeast Spain to the Christian area of Valencia (East Spain) at the beginning of the 14th century; later on, the celebrated Manises and Paterna workshops were formed. Although these ceramics have been studied widely in terms of production technology (ceramic body, glazes and luster) using an array of diverse analytical techniques, until now, an RM study has not been carried out. This paper presents results regarding the complex chemical composition of the glaze and luster coloring agents, and the quality of color manufacturing processes, elucidating firing conditions via spectral components analysis (i.e., Q(n) for stretching/bending components) and polymerization index (Ip), emphasizing chronology and pigment technology changes between both Valencian workshops. Coloring agents identified in glazes and lusters were cobalt present in blue glazes, copper in greenish glazes, copper and cobalt in the turquoise glaze, and pyrolusite in black glazes. Tin oxyde was used as an opacifier in white glazes. Two luster manufacture recipes were recognized mainly based on copper and silver compounds. Calculated firing temperatures were up to 1000 degrees C for white glazes and up to 600 degrees C for luster and color glazes. Copyright (c) 2015 John Wiley & Sons, Ltd.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000363279600002 Publication Date 2015-03-12
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0049-8246 ISBN Additional Links UA library record; WoS full record
Impact Factor Times cited Open Access
Notes Approved no
Call Number UA @ admin @ c:irua:129445 Serial 8300
Permanent link to this record
 
 
Author Danthurebandara, M.; Van Passel, S.; Vanderreydt, I.; Van Acker, K.
Title Assessment of environmental and economic feasibility of Enhanced Landfill Mining Type A1 Journal article
Year 2015 Publication Waste Management Abbreviated Journal Waste Manage
Volume 45 Issue Pages (up) 434-447
Keywords A1 Journal article; Economics; Engineering Management (ENM)
Abstract This paper addresses the environmental and economic performance of Enhanced Landfill Mining (ELFM). Based on life cycle assessment and life cycle costing, a detailed model is developed and is applied to a case study, i.e. the first ELFM project in Belgium. The environmental and economic analysis is performed in order to study the valorisation of different waste types in the landfill, such as municipal solid waste, industrial waste and total waste. We found that ELFM is promising for the case study landfill as greater environmental benefits are foreseen in several impact categories compared to the landfills current situation (the Do-nothing scenario). Among the considered processes, the thermal treatment process dominates both the environmental and economic performances of ELFM. Improvements in the electrical efficiency of thermal treatment process, the calorific value of refuse derived fuel and recovery efficiencies of different waste fractions lead the performance of ELFM towards an environmentally sustainable and economically feasible direction. Although the environmental and economic profiles of ELFM will differ from case to case, the results of this analysis can be used as a benchmark for future ELFM projects.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000364796800048 Publication Date 2015-02-21
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0956-053x ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 4.03 Times cited 30 Open Access
Notes ; The authors would like to acknowledge the funding of this study by the IWT-O&O ELFM project 'Closing the Circle & Enhanced Landfill Mining as part of the Transition to Sustainable Materials Management' and the valuable discussions with Group Machiels (Belgium). ; Approved Most recent IF: 4.03; 2015 IF: 3.220
Call Number UA @ admin @ c:irua:129878 Serial 6156
Permanent link to this record
 
 
Author Danthurebandara, M.; Van Passel, S.; Vanderreydt, I.; Van Acker, K.
Title Environmental and economic performance of plasma gasification in Enhanced Landfill Mining Type A1 Journal article
Year 2015 Publication Waste Management Abbreviated Journal Waste Manage
Volume 45 Issue Pages (up) 458-467
Keywords A1 Journal article; Economics; Engineering sciences. Technology; Engineering Management (ENM)
Abstract This paper describes an environmental and economic assessment of plasma gasification, one of the viable candidates for the valorisation of refuse derived fuel from Enhanced Landfill Mining. The study is based on life cycle assessment and life cycle costing. Plasma gasification is benchmarked against conventional incineration, and the study indicates that the process could have significant impact on climate change, human toxicity, particulate matter formation, metal depletion and fossil depletion. Flue gas emission, oxygen usage and disposal of residues (plasmastone) are the major environmental burdens, while electricity production and metal recovery represent the major benefits. Reductions in burdens and improvements in benefits are found when the plasmastone is valorised in building materials instead of landfilling. The study indicates that the overall environmental performance of plasma gasification is better than incineration. The study confirms a trade-off between the environmental and economic performance of the discussed scenarios. Net electrical efficiency and investment cost of the plasma gasification process and the selling price of the products are the major economic drivers.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000364796800050 Publication Date 2015-06-25
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0956-053x ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 4.03 Times cited 12 Open Access
Notes ; The authors would like to acknowledge the funding of this study by the IWT-O&O ELFM project 'Closing the Circle & Enhanced Landfill Mining as part of the Transition to Sustainable Materials Management' and the valuable discussions with Group Machiels and VITO (Belgium). ; Approved Most recent IF: 4.03; 2015 IF: 3.220
Call Number UA @ admin @ c:irua:129875 Serial 6197
Permanent link to this record
 
 
Author Rehor, I.; Lee, K.L.; Chen, K.; Hajek, M.; Havlik, J.; Lokajova, J.; Masat, M.; Slegerova, J.; Shukla, S.; Heidari, H.; Bals, S.; Steinmetz, N.F.; Cigler, P.
Title Plasmonic nanodiamonds : targeted coreshell type nanoparticles for cancer cell thermoablation Type A1 Journal article
Year 2015 Publication Advanced healthcare materials Abbreviated Journal Adv Healthc Mater
Volume 4 Issue 4 Pages (up) 460-468
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Targeted biocompatible nanostructures with controlled plasmonic and morphological parameters are promising materials for cancer treatment based on selective thermal ablation of cells. Here, coreshell plasmonic nanodiamonds consisting of a silica-encapsulated diamond nanocrystal coated in a gold shell are designed and synthesized. The architecture of particles is analyzed and confirmed in detail using electron tomography. The particles are biocompatibilized using a PEG polymer terminated with bioorthogonally reactive alkyne groups. Azide-modified transferrin is attached to these particles, and their high colloidal stability and successful targeting to cancer cells overexpressing the transferrin receptor are demonstrated. The particles are nontoxic to the cells and they are readily internalized upon binding to the transferrin receptor. The high plasmonic cross section of the particles in the near-infrared region is utilized to quantitatively ablate the cancer cells with a short, one-minute irradiation by a pulse 750-nm laser.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000349961600014 Publication Date 2015-02-18
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 2192-2640; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 5.11 Times cited 30 Open Access OpenAccess
Notes 335078 Colouratom; ECAS_Sara; (ROMEO:yellow; preprint:; postprint:restricted ; pdfversion:cannot); Approved Most recent IF: 5.11; 2015 IF: 5.797
Call Number c:irua:125375 Serial 2647
Permanent link to this record
 
 
Author Cagno, S.; Cosyns, P.; Ceglia, A.; Nys, K.; Janssens, K.
Title The use of vitrum obsianum in the Roman Empire: some new insights and future prospects Type A1 Journal article
Year 2015 Publication Periodico di mineralogia Abbreviated Journal Period Mineral
Volume 84 Issue 3a Pages (up) 465-482
Keywords A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Abstract The research on the use of obsidian in the Mediterranean is extensive but concerns almost exclusively volcanic glass from prehistoric and Bronze Age contexts. The consumption of obsidian during the Roman imperial period, however, has only occasionally received attention. Never a comprehensive account on what the Romans made in vitrum obsianum has been set up, nor have the sources exploited by them been examined. This paper provides a concise overview of the current knowledge on obsidian during the Roman imperial period and offers an introductory outline on potential research. The ancient writers inform us about the use of volcanic glass to create exclusive vessels, gemstones, mirrors and sculpture, but also about the creation of black appearing man-made glass initiated as a cheap and easier workable substitute of obsidian. The archaeological data on the other hand propose a more complex story with the occurrence of obsidian chunks in early Roman secondary glass workshops, and the bulky use of obsidian in late Antiquity to produce tesserae for the creation of wall and vault mosaics. Because it is extremely difficult to visually distinguish natural obsidian from man-made glass imitations we present in this paper data collected by means of non-destructive chemico-physical analyses SEM-EDX, portable X-ray fluorescence (p-XRF) and Raman spectroscopy to easily distinguish man-made glass from natural obsidian. In particular the use of portable instruments makes possible in situ analysis of objects in archaeological depots or museum collections to help defining distribution networks to better understand the shifting consumption patterns in Antiquity.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000365632500007 Publication Date
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0369-8963 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 0.883 Times cited 2 Open Access
Notes ; Our sincere gratitude goes to Cecile Evers and Natacha Masar to have granted permission for studying and analysing various obsidian artefacts within the collections of the Royal Museums of Art and History, Brussels (Belgium). We are also very grateful to Roald Doctor, Daniele Foy and Laudine Robin, respectively for having provided the material from Carthage, for the Sidi Jdidi tessera and Lyon. Our appreciation also goes to Ian Freestone and Andrew Meek respectively for having worked out and provided the internal report on the horse foreleg in the British Museum. Finally we wish to thank Jennifer Price, Maria Grazia Diani respectively for the information on the Stanwick fragment and the piece in the Pogliaghi-Varesse collection. This research was supported by the Hercules Foundation (Brussels) with the grant AUHA09004 and FWO (Brussels, Belgium) projects no. G.0C12.13 and G.01769.09 and partly by the Research Council of Norway through its Centres of Excellence funding scheme, project number 223268/ F50. ; Approved Most recent IF: 0.883; 2015 IF: 0.464
Call Number UA @ admin @ c:irua:130244 Serial 5876
Permanent link to this record