|
“Importance of design and operating parameters in a sonication system for viscous solutions : effects of input power, horn tip diameter and reactor capacity”. Bampouli A, Goris Q, Hussain MN, Louisnard O, Stefanidis GD, Van Gerven T, Chemical engineering and processing 198, 109715 (2024). http://doi.org/10.1016/J.CEP.2024.109715
Abstract: This study investigates the distribution of ultrasound (US) energy in a batch system for solutions with viscosity ranging from 1 to approximately 3000 mPas. Sonication was performed using horn type configurations operating at 20-30 kHz and rated power capacity of 50 or 200 W. Two different tip diameters (3 or 7 mm) and two insertion depths (35 or 25 mm) within vessels of different sizes ( approximate to 60 or 130 ml) were utilized. Additionally, a special conical tip design was employed. For each experimental setup, the calorimetric efficiency was estimated, the cavitationally active regions were visualized using the sonochemiluminescence (SCL) method and bubble cluster formation inside the vessel was macroscopically observed using a high speed camera (HSC). In the viscosity range tested, the calorimetry results showed that the efficiency and continuous operation of the device depend on both the rated power and the horn tip diameter. The ratio between electrical and calorimetric power input remained consistently around 40 to 50% across the different configurations for water, but for the 123.2 mPas solution exhibited significant variation ranging from 40 to 85%. Moreover, the power density in the smaller reactor was found to be nearly double compared to the larger one. The SCL analysis showed multiple cavitationally active zones in all setups, and the zones intensity decreased considerably with increase of the solutions viscosity. The results for the cone tip were not conclusive, but can be used as the basis for further investigation. The current research highlights the importance of thoroughly understanding the impact of each design parameter, and of establishing characterization methodologies to assist in the future development of scaled-up, commercial applications.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 4.3
DOI: 10.1016/J.CEP.2024.109715
|
|
|
“Investigation of volatile organic compounds in museum storage areas”. Alvarez-Martin A, Wilcop M, Anderson R, Wendt D, Barden R, Kavich GM, Air Quality Atmosphere And Health 14, 1797 (2021). http://doi.org/10.1007/S11869-021-01054-2
Abstract: This study investigates the complex mixture of volatile organic compounds (VOCs) released by and accumulated within a collection of historic medicinal, pharmaceutical, and cosmetic artifacts housed at the National Museum of American History (Smithsonian Institution). In recent years, staff have become concerned, both for the safety of the objects and for personnel working in the collection, about strong unremediated odors accumulating within several storage cabinets. Museum staff also wondered if non-odorous off-gassing might need remediation. Solid-phase microextraction combined with gas chromatography–mass spectrometry analysis (SPME–GC–MS) was used to identify VOCs present in the storage room housing the collection. Over 160 compounds were detected and identified overall. Among these, 49 appeared to be directly related to ingredients used in the manufacture of many collection items. The results of the study suggest that SPME–GC–MS can be a strong tool for the rapid screening of multicomponent museum collections exhibiting off-gassing problems, before the pursuit of other more tedious analytical approaches. Additionally, the study reveals valuable insight into the characteristic volatile emission of historic medicinal, pharmaceutical, and cosmetic artifacts, increasing understanding of, and decision-making for, similar collections of objects. Eventually, it is hoped that this information can be used to inform mitigation strategies for the capture and reduction of VOCs in collections storage areas.
Keywords: A1 Journal article; Engineering sciences. Technology; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Antwerp X-ray Imaging and Spectroscopy (AXIS)
Impact Factor: 3.184
DOI: 10.1007/S11869-021-01054-2
|
|
|
“Eliciting farmers' preferences and willingness to pay for land use attributes in Northwest Ethiopia : a discrete choice experiment study”. Admasu WF, Van Passel S, Nyssen J, Minale AS, Tsegaye EA, Land Use Policy 109 (2021). http://doi.org/10.1016/J.LANDUSEPOL.2021.105634
Abstract: This study investigates farmers' preferences and willingness to pay for cropland attributes in Bahir Dar, north-west Ethiopia. A choice experiment is used to elicit farmers' preferences between different land use attributes, including a monetary attribute. The study was conducted in the croplands that are threatened by land expro-priation for urban expansion. A survey was undertaken with 144 farmers in four rural kebeles surrounding the city (Addis Alem, Weramit, Wereb and Zenzelima). In the survey, respondents were provided with hypothetical land purchasing decisions, with three alternatives (i.e., two hypothetical parcels and an opt-out option). A choice experiment was undertaken to measure farmers' interest in different types of croplands, which varies with respect to irrigability, number of trees per ha, soil erosion resistance and water holding capacity of the cropland. Estimation of two mixed logit models was carried out. The estimation results show that, although the farmers did not show strong preferences for each attribute of the cropland, many farmers in the area showed interest in the proposed alternative croplands. Farmers show more interest for the land that is irrigable, gentle slope and with medium water holding capacity. The results also indicate that farmers assign highest marginal willingness to pay (MWTP) (79.01 ETB per square meter) for irrigated land, followed by medium water holding capacity with MWTP of 52.13 ETB per square meter. We believe that the results of this study would help land use policy and decision makers in the study area to consider the various attributes of cropland in land use planning, including land expropriation programs, which assures the sustainability of ecosystem services.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
Impact Factor: 3.089
DOI: 10.1016/J.LANDUSEPOL.2021.105634
|
|
|
“Surface modification of mesostructured cellular foam to enhance hydrogen storage in binary THF/H₂, clathrate hydrate”. Kummamuru NB, Ciocarlan R-G, Houlleberghs M, Martens J, Breynaert E, Verbruggen SW, Cool P, Perreault P, Sustainable energy &, fuels , 1 (2024). http://doi.org/10.1039/D4SE00114A
Abstract: This study introduces solid-state tuning of a mesostructured cellular foam (MCF) to enhance hydrogen (H-2) storage in clathrate hydrates. Grafting of promoter-like molecules (e.g., tetrahydrofuran) at the internal surface of the MCF resulted in a substantial improvement in the kinetics of formation of binary H-2-THF clathrate hydrate. Identification of the confined hydrate as sII clathrate hydrate and enclathration of H-2 in its small cages was performed using XRD and high-pressure H-1 NMR spectroscopy respectively. Experimental findings show that modified MCF materials exhibit a similar to 1.3 times higher H-2 storage capacity as compared to non-modified MCF under the same conditions (7 MPa, 265 K, 100% pore volume saturation with a 5.56 mol% THF solution). The enhancement in H-2 storage is attributed to the hydrophobicity originating from grafting organic molecules onto pristine MCF, thereby influencing water interactions and fostering an environment conducive to H-2 enclathration. Gas uptake curves indicate an optimal tuning point for higher H-2 storage, favoring a lower density of carbon per nm(2). Furthermore, a direct correlation emerges between higher driving forces and increased H-2 storage capacity, culminating at 0.52 wt% (46.77 mmoles of H-2 per mole of H2O and 39.78% water-to-hydrate conversions) at 262 K for the modified MCF material with fewer carbons per nm(2). Notably, the substantial H-2 storage capacity achieved without energy-intensive processes underscores solid-state tuning's potential for H-2 storage in the synthesized hydrates. This study evaluated two distinct kinetic models to describe hydrate growth in MCF. The multistage kinetic model showed better predictive capabilities for experimental data and maintained a low average absolute deviation. This research provides valuable insights into augmenting H-2 storage capabilities and holds promising implications for future advancements.
Keywords: A1 Journal article; Engineering sciences. Technology; Laboratory of adsorption and catalysis (LADCA)
DOI: 10.1039/D4SE00114A
|
|
|
“Valorization of stainless steel slag by selective chromium recovery and subsequent carbonation of the matrix material”. Kim E, Spooren J, Broos K, Nielsen P, Horckmans L, Geurts R, Vrancken KC, Quaghebeur M, Journal of cleaner production 117, 221 (2016). http://doi.org/10.1016/J.JCLEPRO.2016.01.032
Abstract: This study focuses on the recycling of stainless steel (SS) slags containing about 1.2 wt% of chromium (Cr). The selective recovery of Cr from SS slag by a hydrometallurgical method (alkaline pressure leaching) was investigated. Leaching experiments were carried out based on 2(4-1) factorial design of experiment (DOE) with the following parameters: NaOH concentration, temperature, leaching time, and mechanical activation (MA). Results show that temperature and MA are the most influencing factors for an enhanced Cr leaching. The maximum Cr leaching was 46% at 1 M NaOH, 240 degrees C, 6 h, MA 30 min, while the matrix material was dissolved only to a limited extent (Al 2.88%, Si 0.12%, Ca 0.05%). After Cr leaching followed by alkali washing, a carbonation treatment is proposed to stabilize the remaining Cr in the matrix material and make the subsequent recycling of the matrix material as a construction material possible. (C) 2016 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.JCLEPRO.2016.01.032
|
|
|
“Statistical analysis of porcelain tiles' technical properties : full factorial design investigation on oxide ratios and temperature”. Zamani M, Yapicioglu H, Kara A, Sevik C, Physica scripta 98, 125953 (2023). http://doi.org/10.1088/1402-4896/AD0AE9
Abstract: This study focuses on optimizing the composition and firing temperature of porcelain tiles using statistical analysis techniques. A full factorial design, including model adequacy checking, analysis of variance, Pareto charts, interaction plots, regression model, and response optimizer is employed. The key factors were the Seger ratios of SiO2/Al2O3, Na2O/K2O, MgO/CaO, and firing temperature. The response variables investigated were bulk density, water absorption, linear shrinkage, coefficient of thermal expansion (at 500 degrees C), and strength. The statistical analysis revealed highly significant results, which were further validated, confirming their reliability for practical use in the production of porcelain tiles. The study demonstrated the effectiveness of utilizing Seger formulas and properties of typical raw materials to accurately predict the final properties of ceramic tiles. By employing SiO2/Al2O3 = 5.2, Na2O/K2O = 1.50, MgO/CaO = 3.0, and firing temperature of 1180 degrees C, optimized properties, such as maximum strength, maximum bulk density, and minimum water absorption, was achieved with a composite desirability of 0.9821.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.9
DOI: 10.1088/1402-4896/AD0AE9
|
|
|
“Uncoupling the solids retention times of flocs and granules in mainstream deammonification : a screen as effective out-selection tool for nitrite oxidizing bacteria”. Han M, Vlaeminck SE, Al-Omari A, Wett B, Bott C, Murthy S, De Clippeleir H, Bioresource technology 221, 195 (2016). http://doi.org/10.1016/J.BIORTECH.2016.08.115
Abstract: This study focused on a physical separator in the form of a screen to out-select nitrite oxidizing bacteria (NOB) for mainstream sewage treatment. This separation relied on the principle that the NOB prefer to grow in flocs, while anammox bacteria (AnAOB) reside in granules. Two types of screens (vacuum and vibrating) were tested for separating these fractions. The vibrating screen was preferred due to more moderate normal forces and additional tangential forces, better balancing retention efficiency of AnAOB granules (41% of the AnAOB activity) and washout of NOB (92% activity washout). This operation resulted in increased NOB out-selection (AerAOB/NOB ratio of 2.3) and a total nitrogen removal efficiency of 70% at influent COD/N ratio of 1.4. An effluent total nitrogen concentration <10 mg N/L was achieved using this novel approach combining biological selection with physical separation, opening up the path towards energy positive sewage treatment. (C) 2016 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.BIORTECH.2016.08.115
|
|
|
“Environmental sustainability perception toward obvious recovered waste content in paper-based packaging : an online and in-person survey best-worst scaling experiment”. Van Schoubroeck S, Chacon L, Reynolds AM, Lavoine N, Hakovirta M, Gonzalez R, Van Passel S, Venditti RA, Resources, conservation and recycling 188, 106682 (2023). http://doi.org/10.1016/J.RESCONREC.2022.106682
Abstract: This study explores consumers' visual sustainability impressions of paper-based packaging that has incorporated obvious waste content. Two research questions were addressed concerning (i) the environmental sustainability perception of noticeable waste content in packaging and (ii) the impact of the presentation format (i.e., online versus in-person surveys) when studying these perceptions. Best-worst scaling experiments were conducted, which made respondents choose the 'most' and 'least' environmentally friendly package. Packages were designed using paperboard substrates blending either brown linerboard or white hardwood pulp with different recovered waste materials. The results showed that consumers perceive obvious waste-containing packaging as more environmentally friendly than classical packaging (with no visual waste). Samples with a brown base and agricultural waste were perceived as more sustainable compared to white packaging and the use of paper waste. In addition, the presentation format changed respondents' perception, and should therefore be carefully considered when designing surveys.
Keywords: A1 Journal article; Engineering Management (ENM)
Impact Factor: 13.2
DOI: 10.1016/J.RESCONREC.2022.106682
|
|
|
“Farmers' preferences and willingness to pay for improved irrigation water supply program : a discrete choice experiment”. Chekol Zewdie M, Moretti M, Tenessa DB, Van Passel S, Environment, development and sustainability , 1 (2023). http://doi.org/10.1007/S10668-023-03759-Z
Abstract: This study examines smallholder farmers' preferences and willingness to pay for an improved irrigation water supply program in northwest Ethiopia. We employed a discrete choice experiment with five attributes and three levels. Data were collected from randomly selected sample households of both irrigation users and non-users. A total of 379 respondents participated, and a mixed logit model was used to analyze the household-level survey data. The result indicates that to deviate from the business-as-usual scenario, smallholder farmers are willing to pay between 3,228 and 8,327 Ethiopian Birr per hectare of irrigated land. Furthermore, the results showed a strong public preference for access to produce cash crops, followed by irrigation water availability in the dry season, and adequate access to improved farm inputs. The results also provide useful information for policymakers and suggested possibilities for generating finance from farmers to cover the operation and maintenance costs of irrigation schemes. Also, this study result reveals that irrigation development and expansion must be integrated into a comprehensive support package that combines irrigation water with access to improved farm inputs and access to produce cash crops on farmers' farm plots.
Keywords: A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 4.9
DOI: 10.1007/S10668-023-03759-Z
|
|
|
“Exploring benzyl alcohol derivatives and related compounds in the cleaning of oil paintings”. Liu C(T), Alvarez-Martin A, Keune K, Studies in conservation , 1 (2023). http://doi.org/10.1080/00393630.2023.2233374
Abstract: This study examines five benzyl alcohol derivatives and three chemically similar compounds and compares them against benzyl alcohol in gelled emulsions for the removal of overpaint during cleaning of oil paintings. Comparative cleaning tests using xanthan gels, Pemulen® TR-2 gels, and neat solvent were made on overpaint on fragments of a seventeenth-century test painting. This approach demonstrated that molecular changes to a benzyl alcohol core resulted in enhanced control during the cleaning process. In some cases a benzyl alcohol derivative enabled selective removal of non-original material, when benzyl alcohol appeared to affect the original paint. Select derivatives were also tested in an area of overpaint on a sixteenth-century oil on panel painting by Jan van Scorel in the Rijksmuseum Collection through modifying the chemical activity of benzyl alcohol. Finally, two GC-MS-based methods were used to monitor benzyl alcohol retention and possible oxidation in paint layers post-treatment.
Keywords: A1 Journal article; Engineering sciences. Technology; Antwerp X-ray Imaging and Spectroscopy (AXIS)
Impact Factor: 0.8
DOI: 10.1080/00393630.2023.2233374
|
|
|
“A Ricardian analysis of climate change impacts on Japan's agriculture : accounting for solar radiation”. Okamura I, Van Passel S, Fabri C, Senda T, Climate change economics 14, 2350022 (2023). http://doi.org/10.1142/S2010007823500227
Abstract: This study evaluates the effects of climate change on the net revenue of farmers in Japan. We adopted the Ricardian model, which implicitly accounts for farmers’ full adaptation. The main findings of this study are as follows. First, the Ricardian regression shows that changes in temperature significantly impact farmers’ net revenue. In contrast, changes in precipitation have limited effects on farmers’ net revenue. The results of future predictions showed that the effects of climate change are positive across the country, with varying degrees between north and south. These results are more optimistic than those in the existing literature, which frequently reveal negative climate change impacts in southern Japan. However, it should be noted that this model assumes full adaptation and does not consider the transition costs of farmers, and understanding the actual adaptive measures is an important remaining issue.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
DOI: 10.1142/S2010007823500227
|
|
|
“Some critical observations about the degradation of glass : the formation of lamellae explained”. Schalm O, Nuyts G, Janssens K, Journal Of Non-Crystalline Solids 569, 120984 (2021). http://doi.org/10.1016/J.JNONCRYSOL.2021.120984
Abstract: This study demonstrates that the mechanism responsible for the transformation of glass into a degradation layer is pH-dependent. In acid conditions, the transformed glass is homogeneous and brittle. In mild alkaline conditions, transformed glass is heterogeneous due to the presence of lamellae composed of silica nanoparticles and the occurrence of Ca-rich inclusions. The fundamental difference between acid and alkaline conditions cannot be explained by the currently accepted degradation mechanism based on ion exchange. To explain this critical observation, we propose a refined degradation mechanism based on existing knowledge that involves several inwardly moving reaction fronts. The fronts responsible for the transformation of the silicate network into amorphous silica are also responsible for the morphology of the transformed glass. We have identified the feedback mechanism that explains the formation of lamellae in alkaline conditions.
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Impact Factor: 2.124
DOI: 10.1016/J.JNONCRYSOL.2021.120984
|
|
|
“Field demonstration and evaluation of the passive flux meter on a CAH groundwater plume”. Verreydt G, Annable MD, Kaskassian S, van Keer I, Bronders J, Diels L, Vanderauwera P, Environmental Science and Pollution Research 20, 4621 (2013). http://doi.org/10.1007/S11356-012-1417-8
Abstract: This study comprises the first application of the Passive Flux Meter (PFM) for the measurement of chlorinated aliphatic hydrocarbon (CAH) mass fluxes and Darcy water fluxes in groundwater at a European field site. The PFM was originally developed and applied to measurements near source zones. The focus of the PFM is extended from near source to plume zones. For this purpose, 48 PFMs of 1.4 m length were constructed and installed in eight different monitoring wells in the source and plume zone of a CAH-contaminated field site located in France. The PFMs were retrieved, sampled, and analyzed after 3 to 11 weeks of exposure time, depending on the expected contaminant flux. PFM evaluation criteria include analytical, technical, and practical aspects as well as conditions and applicability. PFM flux data were compared with so-called traditional soil and groundwater concentration data obtained using active sampling methods. The PFMs deliver reasonable results for source as well as plume zones. The limiting factor in the PFM applicability is the exposure time together with the groundwater flux. Measured groundwater velocities at the field site range from 2 to 41 cm/day. Measured contaminant flux data raise up to 13 g/m(2)/day for perchloroethylene in the plume zone. Calculated PFM flux averaged concentration data and traditional concentration data were of similar magnitude for most wells. However, both datasets need to be compared with reservation because of the different sampling nature and time. Two important issues are the PFM tracer loss during installation/extraction and the deviation of the groundwater flow field when passing the monitoring well and PFM. The demonstration of the PFM at a CAH-contaminated field site in Europe confirmed the efficiency of the flux measurement technique for source as well as plume zones. The PFM can be applied without concerns in monitoring wells with European standards. The acquired flux data are of great value for the purpose of site characterization and mass discharge modeling, and can be used in combination with traditional soil and groundwater sampling methods.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL); Biochemical Wastewater Valorization & Engineering (BioWaVE)
DOI: 10.1007/S11356-012-1417-8
|
|
|
“Enrichment and adaptation yield high anammox conversion rates under low temperatures”. De Cocker P, Bessiere Y, Hernandez-Raquet G, Dubos S, Mozo I, Gaval G, Caligaris M, Barillon B, Vlaeminck SE, Sperandio M, Bioresource technology 250, 505 (2018). http://doi.org/10.1016/J.BIORTECH.2017.11.079
Abstract: This study compared two anammox sequencing batch reactors (SBR) for one year. SBRconstantT was kept at 30 °C while temperature in SBRloweringT was decreased step-wise from 30 °C to 20 °C and 15 °C followed by over 140 days at 12.5 °C and 10 °C. High retention of anammox bacteria (AnAOB) and minimization of competition with AnAOB were key. 5-L anoxic reactors with the same inoculum were fed synthetic influent containing 25.9 mg NH4+-N/L and 34.1 mg NO2−-N/L (no COD). Specific ammonium removal rates continuously increased in SBRconstantT, reaching 785 mg NH4+-N/gVSS/d, and were maintained in SBRloweringT, reaching 82.2 and 91.8 mg NH4+-N/gVSS/d at 12.5 and 10 °C respectively. AnAOB enrichment (increasing hzsA and 16S rDNA gene concentrations) and adaptation (shift from Ca. Brocadia to Ca. Kuenenia in SBRloweringT) contributed to these high rates. Rapidly settling granules developed, with average diameters of 1.2 (SBRconstantT) and 1.6 mm (SBRloweringT). Results reinforce the potential of anammox for mainstream applications.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.BIORTECH.2017.11.079
|
|
|
“Laboratory-scale membrane up-concentration and co-anaerobic digestion for energy recovery from sewage and kitchen waste”. Nguyen Thi Tuyet, Nguyen Phuoc Dan, Nguyen Cong Vu, Nguyen Le Hoang Trung, Bui Xuan Thanh, De Wever H, Goemans M, Diels L, Water science and technology 73, 597 (2016). http://doi.org/10.2166/WST.2015.535
Abstract: This study assessed an alternative concept for co-treatment of sewage and organic kitchen waste in Vietnam. The goal was to apply direct membrane filtration for sewage treatment to generate a permeate that is suitable for discharge. The obtained chemical oxygen demand (COD) concentrations in the permeate of ultrafiltration tests were indeed under the limit value (50 mg/L) of the local municipal discharge standards. The COD of the concentrate was 5.4 times higher than that of the initial feed. These concentrated organics were then co-digested with organic kitchen wastes at an organic loading rate of 2.0 kg VS/m(3).d. The volumetric biogas production of the digester was 1.94 +/- 0.34 m(3)/m(3).d. The recovered carbon, in terms of methane gas, accounted for 50% of the total carbon input of the integrated system. Consequently, an electrical production of 64 Wh/capita/d can be obtained when applying the proposed technology with the current wastes generated in Ho Chi Minh City. Thus, it is an approach with great potential in terms of energy recovery and waste treatment.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.2166/WST.2015.535
|
|
|
“Direct sensing of superoxide and its relatives reactive oxygen and nitrogen species in phosphate buffers during cold atmospheric plasmas exposures”. Girard-Sahun F, Lefrancois P, Badets V, Arbault S, Clement F, Analytical Chemistry 94, 5555 (2022). http://doi.org/10.1021/ACS.ANALCHEM.1C04998
Abstract: This study aims at sensing in situ reactive oxygen and nitrogen species (RONS) and specifically superoxide anion (O-2(center dot-)) in aqueous buffer solutions exposed to cold atmospheric plasmas (CAPs). CAPs were generated by ionizing He gas shielded with variable N-2/O-2 mixtures. Thanks to ultramicroelectrodes protected against the high electric fields transported by the ionization waves of CAPs, the production of superoxide and several RONS was electrochemically directly detected in liquids during their plasma exposure. Complementarily, optical emissive spectroscopy (OES) was used to study the plasma phase composition and its correlation with the chemistry in the exposed liquid. The specific production of O-2(center dot-), a biologically reactive redox species, was analyzed by cyclic voltammetry (CV), in both alkaline (pH 11), where the species is fairly stable, and physiological (pH 7.4) conditions, where it is unstable. To understand its generation with respect to the plasma chemistry, we varied the shielding gas composition of CAPs to directly impact on the RONS composition at the plasma-liquid interface. We observed that the production and accumulation of RONS in liquids, including O(2)(center dot-)depends on the plasma composition, with N-2-based shieldings providing the highest superoxide concentrations (few 10s of micromolar at most) and of its derivatives (hundreds of micromolar). In situ spectroscopic and electrochemical analyses provide a high resolution kinetic and quantitative understanding of the interactions between CAPs and physiological solutions for biomedical applications.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 7.4
DOI: 10.1021/ACS.ANALCHEM.1C04998
|
|
|
“Plasma medicine technologies”. Kaushik NK, Bekeschus S, Tanaka H, Lin A, Choi EH, Applied Sciences-Basel 11, 4584 (2021). http://doi.org/10.3390/APP11104584
Abstract: This Special Issue, entitled “Plasma Medicine Technologies”, covers the latest remarkable developments in the field of plasma bioscience and medicine. Plasma medicine is an interdisciplinary field that combines the principles of plasma physics, material science, bioscience, and medicine, towards the development of therapeutic strategies. A study on plasma medicine has yielded the development of new treatment opportunities in medical and dental sciences. An important aspect of this issue is the presentation of research underlying new therapeutic methods that are useful in medicine, dentistry, sterilization, and, in the current scenario, that challenge perspectives in biomedical sciences. This issue is focused on basic research on the characterization of the bioplasma sources applicable to living cells, especially to the human body, and fundamental research on the mutual interactions between bioplasma and organic–inorganic liquids, and bio or nanomaterials.
Keywords: Editorial; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.679
DOI: 10.3390/APP11104584
|
|
|
“Critical challenges towards the commercial rollouts of a LOHC-based H2 economy”. Perreault P, Van Hoecke L, Pourfallah H, Kummamuru NB, Boruntea C-R, Preuster P, Current opinion in green and sustainable chemistry 41, 100836 (2023). http://doi.org/10.1016/J.COGSC.2023.100836
Abstract: This short review discusses recent developments related to the storage and release of hydrogen from liquid organic hydrogen carriers (LOHCs). It focusses on three areas of recent literature: the application and development of novel, alternative LOHC systems, process development and process integration in the storage and release of hydrogen from LOHCs, and the electrochemical conversion of LOHCs. For the novel LOHC systems, we briefly focus on reaction enthalpy and storage capacity as main KPIs for the comparison of those systems and discuss the technical availability on a relevant scale. In the field of process- and reactor development our emphasis lies on the power density of the chemical conversion units. The LOHC technology still requires further development to reach the necessary energy efficiency, flexibility and overall research maturity for market competitivity and commercial impact.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 9.3
DOI: 10.1016/J.COGSC.2023.100836
|
|
|
“Economic and environmental multi-objective optimization to evaluate the impact of Belgian policy on solar power and electric vehicles”. De Schepper E, Van Passel S, Lizin S, Vincent T, Martin B, Gandibleux X, Journal of environmental economics and policy 5, 1 (2016). http://doi.org/10.1080/21606544.2015.1019569
Abstract: This research uses multi-objective optimisation to determine the optimal mixture of energy and transportation technologies, while optimising economic and environmental impacts. We demonstrate the added value of using multi-objective mixed integer linear programming (MOMILP) considering economies of scale versus using continuous multi-objective linear programming assuming average cost intervals. This paper uses an improved version to solve MOMILPs exactly. To differentiate optimal solutions with and without subsidies, the impact of policy on the Pareto frontier is assessed. We distinguish between minimising economic life cycle costs (complete rationality) and required investments (bounded rationality). The approach is illustrated using a Belgian company with demands for electricity and transport. Electricity technologies are solar photovoltaics and the grid; transportation includes internal combustion engine vehicles, grid powered battery electric vehicles (BEVs), and solar-powered BEVs. The impact of grid powered BEVs to reduce GHG emissions is limited, yet they are less costly than solar panels to decrease emissions. Current policy measures are found to be properly targeting rational investors who consider life cycle costs, while private (potentially bounded rational) investors often focus on required investments only.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
DOI: 10.1080/21606544.2015.1019569
|
|
|
“Electromagnetic modeling and design of a novel class of complementary split‐ring resonators”. Martínez-Dueñas EJR, de Jong van Coevorden CM, Stukach OV, Panokin NV, Gielis J, Caratelli D, International journal of RF and microwave computer-aided engineering 29, e21582 (2019). http://doi.org/10.1002/MMCE.21582
Abstract: This research study reports the assessment of complementary split ring resonators based on Gielis transformation as basic elements for the design of high‐performance microwave components in printed technology. From the electromagnetic simulation of said structures, suitable equivalent circuit models are extracted and analyzed. Physical prototypes are fabricated and tested for design validation. The obtained results confirm that the adoption of supershaped geometries enables the synthesis of very compact scalable microwave filters.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1002/MMCE.21582
|
|
|
“Gielis transformations for the audiovisual geometry database”. Chapman D, Gielis J, Symmetry : culture and science 32, 177 (2021). http://doi.org/10.26830/SYMMETRY_2021_2_177
Abstract: This publication introduces the audiovisual geometry database with Gielis transformations as initial records for a prototype of the database. A concise overview is given of the rationale behind the database and studying wave phenomena with Gielis transformations. First results on a form of timbral polyphony observed in Gielis curves and future work are briefly discussed.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.26830/SYMMETRY_2021_2_177
|
|
|
Magalhã,es Cunha S (2022) Wave-packet dynamics and electronic transport properties in 2D materials. 219 p
Abstract: This piece of work is twofold. First, the time evolution of wave-packets in 2D systems is analyzed by the Split-Operator technique in three different scenarios: in multilayer phosphorene, the transient oscillations in the time-dependent average of position and momentum were observed due to the zitterbewegung effect, and the wave packet propagates non-uniformly along the space deforming itself into an elliptical shape. These results were corroborated by the Green’s function formalism except for large values of the wave-vector and long times; in 2D semiconductor quantum wires (QWs) with anisotropic effective masses and different angle orientations with respect to the anisotropic axis. We have shown that the greater this angle, the smaller is the energy levels spacing implying in an increase of the accessible electronic states. Additionally, for non-null magnetic field, the quantum Hall edge states are significantly affected by the edge orientation. In the anisotropic case damped oscillations in the average values of velocity in both x and y directions where obtained. Theses oscillations are originated by the QW geometry but also from subwavepackets with different momentum orientations, whereas for isotropic QWs the wavepacket disperses without splitting; in the third scenario the split-operator technique was used to study the Landau levels, the wave packet trajectories and velocities of electrons in graphene at low-energy regime described by a modified Dirac equation where the momentum-operator is written in a generalized form as result of applying the position-dependent translation operator formalism (PDTO). In the second part of this thesis, the electronic and tunneling properties of α − T3 lattices were studied. Electrons in these lattices behave analogous to integer-spin Dirac Fermions. The presence of a third atomic site in the unit cell leads to a flat band in the energy spectrum, providing unique electronic and tunneling properties. The presence of a super-periodic potential and the inclusion of symmetry-breaking terms results in deviations of the atomic equivalence between the atomic sites affecting the Dirac points and the band-gap. Small deviations in the equivalence between the atomic sites and the number of barriers change the transmission properties in these lattices. Additionally, new tunneling regions are possible by adjusting the symmetry between the atomic sites and affect the omnidirectional total transmission called super-Klein tunneling observed in these lattices. We compare those results to the tunneling probabilities through regions where the energy spectrum changes from linear with a middle flat band to a hyperbolic dispersion.
Keywords: Doctoral thesis; Condensed Matter Theory (CMT)
|
|
|
“Transposing testing from lab to on-site environment : a case of cocaine powder sampling”. Van Loon J, De Jong M, De Wael K, Du Bois E, (2020)
Abstract: This paper reports on the transition process to convert a specific lab technique to the on-site, real-life environment. Bringing a lab test to an on-site environment involves many difficulties regarding to the context, people skills and environmental support. Within this project, a case about sampling for an electrochemical measurement, was investigated as a basis to reason upon some general conclusions related to the process of transposing lab-tests to an on-site environment. The current lab test was analysed and compared with a focus group discussion with future users. Based on the findings, assumptions for the new sampling technique in the specific case were formulated. New low-tech methods to achieve the sampling were extensively tested and verified. Starting from this chosen case an argumentation was set up to generalise the conclusions, by reasoning on other cases of products that already passed this transition to the field. Based on a comparison, we could discuss that the selected parameters related to impact of the context environment, of the people that should handle the tests, related to the reasons for transposing the technology, and related to the technology that will be transposed to the on-site environment, were of importance of almost all cases and can therefore be considered as context-independent and related to the transfer to on-site testing.
Keywords: P3 Proceeding; Engineering sciences. Technology; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Product development
|
|
|
“Impedimetric sensing of the immuno-enzymatic reaction of gliadin with a collagen-modified electrode”. Bottari F, Moretto LM, Ugo P, Electrochemistry communications 97, 51 (2018). http://doi.org/10.1016/J.ELECOM.2018.10.011
Abstract: This paper presents a previously unexplored biosensing strategy for detecting gliadin which exploits the crosslinking of gliadin with collagen, catalyzed by transglutaminase at the interfacial electron transfer rate, on a modified electrode. The process is monitored by electrochemical impedance spectroscopy using a glassy carbon electrode coated with a collagen layer. To validate the specificity of the response as well as to eliminate possible interferences from other proteins, such as soy protein or casein, the captured gliadin is further reacted with a specific anti-gliadin antibody. Changes in charge transfer resistance, measured from the Nyquist plots, scale linearly with the gliadin concentration in the range 5-20 mg/L, a range suitable for testing the gliadin concentration in gluten-free food commodities.
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
DOI: 10.1016/J.ELECOM.2018.10.011
|
|
|
“CFD- and radiation field modeling of a gas phase photocatalytic multi-tube reactor”. Roegiers J, van Walsem J, Denys S, Chemical engineering journal 338, 287 (2018). http://doi.org/10.1016/J.CEJ.2018.01.047
Abstract: This paper focusses on the development of a Multiphysics model as a tool for assessing the performance of a multi-tube photoreactor. The model predicts the transient behavior of acetaldehyde concentration, as a model compound for the organic fraction of the indoor air pollutants, under varying sets of conditions. A 3D-model couples radiation field modeling with reaction kinetics and fluid dynamics in order to simulate the transport of the pollutant as it progresses through the reactor. A model-based approach is proposed to determine the layer thickness and refractive index of different P25-powder modified solgel coatings, using an optimization procedure to estimate these parameters based on UV-irradiance measurements. The radiation field model was able to accurately predict the irradiance on the catalytic surface within the reactor. Consequently, the radiation field model was used to define an irradiance dependent reaction rate constant in a coupled Multiphysics model. An optimization routine was deployed to estimate the adsorption, desorption- and photocatalytic reaction rate constants on the TiO2-surface, using experimentally determined, transient outlet concentrations of acetaldehyde. Additionally, a validation test was performed in an air-tight climate chamber at much higher flow rates, higher irradiance and realistic indoor pollutant concentrations to emphasize the reliability and accuracy of the parameters for adsorption, desorption and photocatalytic reaction. The developed model makes it possible to optimize the reactor design and scale-up for commercial applications.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.CEJ.2018.01.047
|
|
|
“Comparative assessment of air quality in two health resorts using carbon isotopes and palynological analyses”. Górka M, Jedrysek MO, Maj J, Worobiec A, Buczyńska A, Stefaniak E, Krata A, Van Grieken R, Zwozdziak A, Sówka I, Zwozdziak J, Lewicka-Szczebak D, Atmospheric environment 43, 682 (2009). http://doi.org/10.1016/J.ATMOSENV.2008.09.056
Abstract: This paper describes results of applying the palynological and carbon isotopic analysis of the organic fraction of Total Suspended Particles (TSP) to discriminate distinct pollution sources and assess the anthropogenic impact for the investigated areas. The samples of atmospheric particles were collected in Czerniawa and Cieplice (two health resorts in Lower Silesia, SW Poland) twice a year in summer and winter season (from July 2006 to February 2008). The palynological spectra represent in the vast majority local plant communities without a noticeable contribution of long-transported plant particles. Palynological analysis revealed also differences in the specificity of the two sampling areas, i.e. the higher contribution of identified organic material in Czerniawa stands for more natural character of this site, but is also responsible for the higher allergic pressure when compared to Cieplice. The carbon isotopic composition of TSP varied seasonally (ä13C value from −27.09 in summer to −25.47 in winter). The increased ä13C value in winter (heating period) is most probably caused by uncontrolled contribution of coal soot. On the basis of isotopic mass balance the calculated contribution of anthropogenic organic particles in the atmosphere reached in winter season 72% in Czerniawa and 79% in Cieplice.
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Laboratory Experimental Medicine and Pediatrics (LEMP)
DOI: 10.1016/J.ATMOSENV.2008.09.056
|
|
|
“Power outages and bill savings : a choice experiment on residential demand response acceptability in Delhi”. Srivastava A, Van Passel S, Valkering P, Laes EJW, Renewable &, Sustainable Energy Reviews 143, 110904 (2021). http://doi.org/10.1016/J.RSER.2021.110904
Abstract: This paper conducts a discrete choice experiment among 167 households in the Delhi region in India, to study the acceptability of demand response (DR) programs among upper-income households. Attributes include rate types, rate bands, reductions in power outages, and expected monthly savings. Results indicate a preference for time-of-use pricing over real-time pricing, and a preference for three rate slabs per day over two. Respondents prioritize reductions in power outages and minimizing potential expenses, reflecting the financial sensitivity and energy poverty relative to other countries. Respondents' ages and incomes further affect the value that they attach to reductions in power outages. The paper proposes various structures of DR programs that could achieve high predicted enrollment and concludes by estimating the potential benefits of implementing such programs. Overall, the analysis indicates that a DR program could be feasible in a developing country context, particularly if it is designed keeping in mind local socio-economic considerations. This may be supported through further confirmatory research.
Keywords: A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 8.05
DOI: 10.1016/J.RSER.2021.110904
|
|
|
“Meta-analysis of CO₂, conversion, energy efficiency, and other performance data of plasma-catalysis reactors with the open access PIONEER database”. Salden A, Budde M, Garcia-Soto CA, Biondo O, Barauna J, Faedda M, Musig B, Fromentin C, Nguyen-Quang M, Philpott H, Hasrack G, Aceto D, Cai Y, Jury FA, Bogaerts A, Da Costa P, Engeln R, Galvez ME, Gans T, Garcia T, Guerra V, Henriques C, Motak M, Navarro MV, Parvulescu VI, Van Rooij G, Samojeden B, Sobota A, Tosi P, Tu X, Guaitella O, Journal of energy chemistry 86, 318 (2023). http://doi.org/10.1016/J.JECHEM.2023.07.022
Abstract: This paper brings the comparison of performances of CO2 conversion by plasma and plasma-assisted catalysis based on the data collected from literature in this field, organised in an open access online data-base. This tool is open to all users to carry out their own analyses, but also to contributors who wish to add their data to the database in order to improve the relevance of the comparisons made, and ultimately to improve the efficiency of CO2 conversion by plasma-catalysis. The creation of this database and data-base user interface is motivated by the fact that plasma-catalysis is a fast-growing field for all CO2 con-version processes, be it methanation, dry reforming of methane, methanolisation, or others. As a result of this rapid increase, there is a need for a set of standard procedures to rigorously compare performances of different systems. However, this is currently not possible because the fundamental mechanisms of plasma-catalysis are still too poorly understood to define these standard procedures. Fortunately how-ever, the accumulated data within the CO2 plasma-catalysis community has become large enough to war-rant so-called “big data” studies more familiar in the fields of medicine and the social sciences. To enable comparisons between multiple data sets and make future research more effective, this work proposes the first database on CO2 conversion performances by plasma-catalysis open to the whole community. This database has been initiated in the framework of a H2020 European project and is called the “PIONEER DataBase”. The database gathers a large amount of CO2 conversion performance data such as conversion rate, energy efficiency, and selectivity for numerous plasma sources coupled with or without a catalyst. Each data set is associated with metadata describing the gas mixture, the plasma source, the nature of the catalyst, and the form of coupling with the plasma. Beyond the database itself, a data extraction tool with direct visualisation features or advanced filtering functionalities has been developed and is available online to the public. The simple and fast visualisation of the state of the art puts new results into context, identifies literal gaps in data, and consequently points towards promising research routes. More advanced data extraction illustrates the impact that the database can have in the understanding of plasma-catalyst coupling. Lessons learned from the review of a large amount of literature during the setup of the database lead to best practice advice to increase comparability between future CO2 plasma-catalytic studies. Finally, the community is strongly encouraged to contribute to the database not only to increase the visibility of their data but also the relevance of the comparisons allowed by this tool. (c) 2023 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by ELSEVIER B.V. and Science Press. This is an open access article under the CC BY license (http://creati- vecommons.org/licenses/by/4.0/).
Keywords: A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 13.1
DOI: 10.1016/J.JECHEM.2023.07.022
|
|
|
“Analyzing the impact of land expropriation program on farmers' livelihood in urban fringes of Bahir Dar, Ethiopia”. Fitawok MB, Derudder B, Minale AS, Van Passel S, Adgo E, Nyssen J, Habitat International 129, 102674 (2022). http://doi.org/10.1016/J.HABITATINT.2022.102674
Abstract: This paper analyzes the impact of urban land-use changes on farmers' livelihood around the city of Bahir Dar (Ethiopia). Rapid urban expansion in and around the city has resulted in massive land-use changes in its urban fringes, with land expropriation programs affecting communities' livelihood and the environment. A survey was conducted in three urbanizing villages near Bahir Dar, focusing on 150 farmers who were land-expropriated and 180 farmers who were non-land-expropriated. Regression models and propensity matching scoring are applied to examine the livelihood differences of farmers in terms of farm income, off-farm income, primary expenditure type, and perception of urban expansion benefits to farmers. The results reveal that land expropriation in the area has led to (a) a shift to off-farm income for land expropriated farmers; (b) an increase in their household expenditure on staple foods compared to other expenditure types, including farm inputs; and (c) diverging perceptions on whether and how city expansion benefits farmers in the neighboring villages. Our findings provide insight into the need for tighter and impactful policy actions to ensure the sustainability of urbanization through accommodating expropriated farmers' livelihood changes and protecting natural resources in the area.
Keywords: A1 Journal article; Sociology; Law; Art; Engineering Management (ENM)
Impact Factor: 2.285
DOI: 10.1016/J.HABITATINT.2022.102674
|
|
|
“Structural and institutional heterogeneity among agricultural cooperatives in Ethiopia : does it matter for farmers' welfare?”.Gezahegn TW, Van Passel S, Berhanu T, D'Haese M, Maertens M, Journal Of Agricultural And Resource Economics 46, 325 (2021). http://doi.org/10.22004/AG.ECON.304767
Abstract: This paper analyzes how structural and institutional heterogeneity among irrigation cooperatives shapes the impact of membership on farmers' welfare in northern Ethiopia, using a novel heteroskedasticity-based identification strategy. More specifically, we estimate how cooperative characteristics influence members' income and poverty level. We find that stricter water use regulations have income-enhancing and poverty-reducing effects for farmers. We also find that farmers benefit more from membership in larger, younger, and bottom-up cooperatives initiated through grassroots collective action. Our findings have implications for irrigation development in Ethiopia and call for a better deliberation of organizational heterogeneity in cooperative impact studies
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
Impact Factor: 1
DOI: 10.22004/AG.ECON.304767
|
|