Abstract: It is generally known that radiographic inspection of 1517th century paintings can easily be done with a polychromatic X-ray source using a voltage between 20 kV and 40 kV in combination with classic X-ray films. Unfortunately, the spatial structure of numerous 19th and early 20th century paintings cannot be visualized with conventional radiography due to several reasons such as the use of lead white grounds or low absorbing pigments. Radiographic images are blurred or worse, they do not contain the picture of the painting. During the last decades, many technological innovations have been introduced in the field of radiography but their possibilities in cultural heritage have not been explored in full detail. In our investigation we used phosphor imaging plates, energy dispersive detectors and CCD-cameras in combination with synchrotron radiation and conventional X-ray tubes in order to improve the quality of radiographic images. Several promising techniques that could improve the quality of radiographs of paintings were identified.

Abstract: It is standard practice in virtual reality applications to synthesize binaural audio based on a discrete set of directionally-dependent head-related impulse responses (HRIRs). This set of HRIRs is often time-aligned in a pre-processing step, to allow for high-fidelity interpolation between HRIRs corresponding with neighbouring directions. The fidelity of this operation depends on the similarity of neighbouring aligned HRIRs. The pairwise quality of similarity makes it a difficult criterion to optimize globally and consequently one often resorts to alignment methods based on a specific feature that can be extracted for each HRIR separately, e.g., the first-onset of the peak or the group delay. However, such proxies for similarity are very sensitive to noise and therefore require a high signal-to-noise ratio, which makes them less suitable for processing HRIRs acquired outside an anechoic room. In this paper, we advance a novel alignment method, which maximizes the similarity – defined as the correlation between the full-length HRIRs – between neighbouring aligned HRIRs for all directions at once. We show that this correlation-based alignment procedure outperforms the first-onset alignment with regards to the fidelity of the spherical harmonics representation of both the spectral and interaural time difference (ITD) information, when tested on the KEMAR HRIR and six human HRIRs. Finally, we show that the correlation-based alignment is more robust to noise.

Abstract: Jackson Pollock's Number 1A, 1948 painting was investigated using in situ scanning macro-x-ray fluorescence mapping (MA-XRF) to help characterize the artist's materials and his creative process. A multivariate curve resolution-alternating least squares (MCR-ALS) approach was used to examine the hyperspectral data and obtain distribution maps and signature spectra for the paints he used. The composition of the paints was elucidated based on the chemical elements identified in the signature spectra and a tentative list of pigments, fillers and other additives is proposed for eleven different paints and for the canvas. The paint distribution maps were used to virtually reconstruct the artist process and document the sequence and manner in which Pollock applied the different paints, using deliberate and specific gestures.

Abstract: Knowledge of how heat flows anisotropically in van der Waals (vdW) materials is crucial for thermal management of emerging 2D materials devices and design of novel anisotropic thermoelectric materials. Despite the importance, anisotropic heat transport in vdW materials is yet to be systematically studied and is often presumably attributed to anisotropic speeds of sound in vdW materials due to soft interlayer bonding relative to covalent in-plane networks of atoms. In this work, we investigate the origins of the anisotropic heat transport in vdW materials, through time-domain thermoreflectance (TDTR) measurements and first-principles calculations of anisotropic thermal conductivity of three different phases of MoTe2. MoTe2 is ideal for the study due to its weak anisotropy in the speeds of sound. We find that even when the speeds of sound are roughly isotropic, the measured thermal conductivity of MoTe2 along the c-axis is 5-8 times lower than that along the in-plane axes. We derive meaningful characteristic heat capacity, phonon group velocity, and relaxation times from our first principles calculations for selected vdW materials (MoTe2, BP, h-BN, and MoS2), to assess the contributions of these factors to the anisotropic heat transport. Interestingly, we find that the main contributor to the heat transport anisotropy in vdW materials is anisotropy in heat capacity of the dominant heat-carrying phonon modes in different directions, which originates from anisotropic optical phonon dispersion and disparity in the frequency of heat-carrying phonons in different directions. The discrepancy in frequency of the heat-carrying phonons also leads to similar to 2 times larger average relaxation times in the cross-plane direction, and partially explains the apparent dependence of the anisotropic heat transport on the anisotropic speeds of sound. This work provides insight into understanding of the anisotropic heat transport in vdW materials.

Abstract: Lake Tana is the most important freshwater lake in Ethiopia. Besides pressures on water quality resulting from urbanization and deforestation, the invasion of the exotic water hyacinth (Eichhornia crassipes) poses new threats to the ecosystem. Water hyacinth, endemic to South America, is widely considered as the world's worst aquatic invasive weed. In 2011, the weed appeared on the northern shores of Lake Tana, expanding in south-eastern direction. The lake area affected by water hyacinth was last estimated in 2015 at 34,500 ha, which equals 16% of the total lake surface. In this research, the benefits of water hyacinth control and eradication for the rural population inhabiting the northern and northeastern villages bordering Lake Tana, are investigated. In the area, the population largely depends on farming and fishing. An assessment of the total economic benefit of eradication was conducted. The stakeholder-centered approach led to measuring the willingness to contribute in labor and cash terms. Results showed smallholders in the study are willing to contribute over half-a-million euros annually. Costs of management actions can be weighed to the benefits, where further research is needed on the impact on other stakeholder groups. Moreover, wetland management should advance to explore multiple pathways in an integrated approach: water hyacinth control, water hyacinth utilization and sustainable waste water management. (C) 2020 International Association for Great Lakes Research. Published by Elsevier B.V. All rights reserved.

Abstract: Land-tenure security is integral to local communities' socioeconomic development. It has been a center of debate in academia and for legislators and advocates to implement reforms to enhance efficient and sustainable development in land management. Yet, knowledge gaps remain in how various contract-farming regimes contribute to land-improvement investment and technical efficiency. This study used a data set of 650 farm households collected through a two-stage stratified sampling to investigate the influence of three contract-farming regimes: long-term, medium-term, and short-term contracts, on the land-improvement investment, productivity, and technical efficiency of contract farmers in Punjab, Pakistan. The study used multivariate probit and ordinary least square regression models to examine the posit relationships. The findings highlight that farmers with long-term land contracts have higher per hectare yield, income and profit than those with medium-term and short-term contracts. The results confirm that farmers with medium- and long-term contracts tend to invest more in land-improvement measures, i.e., organic and green manure. Further, the study findings demonstrate that long-term land tenures are more effective when farmers make decisions regarding the on-farm infrastructure, like tube-well installation, tractor ownership, and holding farm logistics. Last, the study results confirm that long-term contracts are more robust regarding technical efficiency. Moreover, the findings support the Marshallian inefficiency hypothesis and extend the literature on contract farming, land-improvement investment, and land use policy, and offer coherent policy actions for stakeholders to improve farmers' productivity, technical efficiency, and income.

Abstract: Landfill mining refers to the re-circulation of resources from the previously deposited wastes–integrating resource recovery with traditional site remediation. Several resources that can be recovered include scrap metals, combustibles, and inert materials. In addition, land can be recovered or landfill void space can be liberated for future wastes. At present, landfill mining is still an emerging concept with few project implementations. Consequently, the assessments of its economic and climate implications are case study-specific, limiting the understanding of its potential in a wider geographical scope. This thesis aims to assess the economic performance and climate impact of landfill mining in Europe towards the development of sound strategies for implementation. Different project setups are assessed in relation to varying factors at the site level such as waste composition and landfill settings, and at the system level such as policy and market conditions and background material and energy. In doing so, a factor-based method is developed and applied to generate multiple scenarios (531, 441 scenarios per project setup) and determine the underlying important factors and their interrelations that drive the results. Such understanding is used to develop and discuss strategies for improvement by addressing relevant questions for specific stakeholders, including project investors (i.e., which landfill sites to prioritize?), landfill mining practitioners (i.e., how to set up such projects?), and policymakers (i.e., which policy instruments can effectively support such projects?). Results show that landfill mining is preferable in terms of climate than economy. Possible improvements are shown by internalizing thermal treatment of combustibles and extending fines residue utilization as construction aggregates. In relation to the choice of project setups, preferable site and system-level conditions are identified in general but it is also discussed that the plausibility of finding such conditions may be difficult at present. This steers the development of more tailored strategies on what can be done now by the landfill practitioners in terms of setting up projects under current policy and market conditions in specific regions, or what can be done by the policymakers in terms of implementing various policy instruments that can drive such changes at the system level. Through this thesis, the future of landfill mining research is guided towards addressing key challenges and potential solutions for improvement. Furthermore, this thesis highlights the role of assessment as a tool for learning and guiding the development of emerging concepts such as landfill mining.

Abstract: Large river catchments with mixed land use capture pesticides from many sources, and degradable pesticides are converted during downstream transport. Unravelling the contribution of pesticide source and the effect of degradation processes is a challenge in such areas. However, insight and understanding of the sources is important for targeted managen-lent, especially when water is abstracted from the river for drinking water production. The river Meuse is such a case. A long-term monitoring data set was applied in a modelling approach for assessing the contribution of waste water treatment plants (WWTPs) and tributaries (sub-basins) to surface water contamination, and to evaluate the effect of decay on the downstream concentrations of glyphosate and AMPA at the point of drinking water abstraction. The results show that WWTPs are important contributors for glyphosate and AMPA in large river catchments with mixed land uses. In the studied area, the river Meuse in the Netherlands, the relative contribution of WWTP effluents is above 29% for glyphosate and around 12% for AMPA. Local industries are found to be potentially big contributors of AMPA. Glyphosate entering the river system is gradually converted to AMPA and other degradation-productions, which results in downstream loads that are considerably lower than the sum of all influxes. In summer when the travel time is longer due to lower discharge, the first order decay of glyphosate in the river Meuse is estimated to result in about 50% reduction of the downstream glyphosate concentrations over a river stretch of 250 km. The contribution of glyphosate decay to the observed AMPA concentrations ranges between 2% and 10%. Contributions are sensitive to seasonal variations in discharge that influence the concentrations through dilution and degradation. (C) 2016 Elsevier B.V. All rights reserved.

Abstract: Laser microprobe mass analysis (LAMMA) was applied to particulate matter from the Atlantic Ocean. Inferring information about the surface layer by LAMMA was not probe X-ray microanalysis (EPXMA). Geochemically relevant groups of particles had been identified by EPXMA and cluster analysis. For both locations, the most abundant ones appeared to be those rich in silicon and the alumino-silicates. Afterwards LAMMA was applied to obtain more information about the trace element composition and surface characteristics. The iron-rich phase appeared to contain significant amounts of heavy metals and of phosphate. Lead appeared to be associated in detectable amounts with alumino-silicates in the Scheldt but not with those in the Atlantic Ocean. Inferring information about the surface layer by LAMMA was not always unambiguous.

Abstract: Laser microprobe mass analysis was applied to study the chemical composition of spheroliths in the Bowman's membrane of patients suffering from primary atypical bandkeratopathy. The inclusions appear to consist mainly of calcium phosphate.

Abstract: Laser microprobe mass spectrometry is used to identify intrarenal microliths; they appear to consist of either oxalate, urate or phosphate. Crystalline and amorphous deposits in rat and human kidney are pin-pointed by the laser beam and their chemical composition determined by mass spectrometry. The method has the potential for wide application in the identification of single organic, inorganic or combination crystals in histological sections.

Abstract: Lattice thermal conductivity (kappa(L)) is of great scientific interest for the development of efficient energy conversion technologies. Therefore, microscopic understanding of phonon transport is critically important for designing functional materials. In our previous study (Roshan et al., ACS Applied Energy Mater. 2021, 5, 882-896), anomalous kappa(L) trends were predicted for rocksalt alkaline-earth chalcogenides (AECs). In the present work, we extended it to alkali halides (AHs) and conducted a thorough investigation to explore the role of atomic mass contrast on lattice dynamics and phonon transport properties of 36 binary compounds (20 AHs + 16 AECs). The calculated spectral and cumulative kappa(L) reveal that low-lying optical phonon modes significantly boost kappa(L) alongside acoustic phonons in materials where the atomic mass ratio approaches unity and cophonocity nears zero. Phonon scattering rates are relatively low for materials with a mass ratio close to one, and the corresponding phonon lifetimes are higher, which enhances kappa(L). Phonon lifetimes play a critical role, outweighing phonon group velocities, in determining the anomalous trends in kappa(L) for both AHs and AECs. To further explore the role of atomic mass contrast in kappa(L), the effect of tensile lattice strain on phonon transport has also been investigated. Under tensile strain, both group velocities and phonon lifetimes decrease in the low frequency range, leading to a decrease in kappa(L). This work provides insights on how atomic mass contrast can tune the contribution of optical phonons to kappa(L) and its implications on scattering rates by either enhancing or suppressing kappa(L). These insights would aid in the selection of elements for designing new functional materials with and without atomic mass contrast to achieve relatively high and low kappa(L) values, respectively.

Abstract: Leaf shape is closely related to economics of leaf support and leaf functions, including light interception, water use, and CO2 uptake, so correct quantification of leaf shape is helpful for studies of leaf structure/function relationships. There are some extant indices for quantifying leaf shape, including the leaf width/length ratio (W/L), leaf shape fractal dimension (FD), leaf dissection index, leaf roundness index, standardized bilateral symmetrical index, etc. W/L ratio is the simplest to calculate, and recent studies have shown the importance of the W/L ratio in explaining the scaling exponent of leaf dry mass vs. leaf surface area and that of leaf surface area vs. leaf length. Nevertheless, whether the W/L ratio could reflect sufficient geometrical information of leaf shape has been not tested. The FD might be the most accurate measure for the complexity of leaf shape because it can characterize the extent of the self-similarity and other planar geometrical features of leaf shape. However, it is unknown how strongly different indices of leaf shape complexity correlate with each other, especially whether W/L ratio and FD are highly correlated. In this study, the leaves of nine Magnoliaceae species (>140 leaves for each species) were chosen for the study. We calculated the FD value for each leaf using the box-counting approach, and measured leaf fresh mass, surface area, perimeter, length, and width. We found that FD is significantly correlated to the W/L ratio and leaf length. However, the correlation between FD and the W/L ratio was far stronger than that between FD and leaf length for each of the nine species. There were no strong correlations between FD and other leaf characteristics, including leaf area, ratio of leaf perimeter to area, fresh mass, ratio of leaf fresh mass to area, and leaf roundness index. Given the strong correlation between FD and W/L, we suggest that the simpler index, W/L ratio, can provide sufficient information of leaf shape for similarly-shaped leaves. Future studies are needed to characterize the relationships among FD and W/L in leaves with strongly varying shape, e.g., in highly dissected leaves.

Abstract: Lignin removal plays a crucial role in the efficient bioconversion of lignocellulose to fermentable sugars. As a delignification process, fungal pretreatment has gained great interest due to its environmental friendliness and low energy consumption. In our previous study, a positive linear correlation between acid-insoluble lignin degradation and the achievable enzymatic saccharification yield has been found, hereby highlighting the importance of the close follow-up of lignin degradation during the solid-state fungal pretreatment process. However, the standard quantification of lignin, which relies on the two-step acid hydrolysis of the biomass, is highly laborious and time-consuming. Vibrational spectroscopy has been proven as a fast and easy alternative; however, it has not been extensively researched on lignocellulose subjected to solid-state fungal pretreatment. Therefore, the present study examined the suitability of near-infrared spectroscopy (NIR) for the rapid and easy assessment of lignin content in poplar wood pretreated with Phanerochaete chrysosporium. Furthermore, the predictive power of the obtained calibration model and the recently published ATR-FTIR spectroscopy-based model were compared for the first time using the same fungus-treated wood data set. PLSR was used to correlate the NIR spectra to the acid-insoluble lignin contents (19.9%-27.1%) of pretreated wood. After normalization and second derivation, a PLSR model with a good coefficient of determination (RCV2 = 0.89) and a low root mean square error (RMSECV = 0.55%) were obtained despite the heterogeneous nature of the fungal solid-state fermentation. The performance of this PLSR model was comparably good to the one obtained by ATR-FTIR (RCV2 = 0.87) while it required more extensive spectral pre-processing. In conclusion, both methods will be highly useful for the high-throughput and user-friendly monitoring of lignin degradation in a solid-state fungal pretreatment-based biorefinery concept.

Abstract: Lignosulfonate-based bioactive coatings as soil improvers for lawns were developed using laccase as a biocatalyst. Incorporation of glycerol, xylitol and sorbitol as plasticizers considerably reduced the brittleness of the synthesized coatings of marine carbonate granules while thermal enzyme inactivation at 100 degrees C enabled the production of stable coatings. Heat inactivation produced stable coatings with a molecular weight of 2000 kDa and a viscosity of 4.5 x 10(-3) Pas. The desired plasticity for the spray coating of soil improver granules was achieved by the addition of 2.7% of xylitol. Agriculture beneficial microorganisms (four different Bacillus species) were integrated into the coatings. The stable coatings protected the marine calcium carbonate granules, maintained the viability of the microorganisms and showed no toxic effects on the germination and growth of model plants including corn, wheat, salad, and tomato despite a slight delay in germination. Moreover, the coatings reduced the dust formation of soil improvers by 70%. CO2 emission analysis showed potential for the reduction of up to 3.4 kg CO2-eq. kg(-1) product, making it a viable alternative to fossil-based coatings.