Records |
Author |
Vassiliev, S.Y.; Laurinavichute, V.K.; Abakumov, A.M.; Govorov, V.A.; Bendovskii, E.B.; Turner, S.; Filatov, A.Y.; Tarasovskii, V.P.; Borzenko, A.G.; Alekseeva, A.M.; Antipov, E.V. |
Title |
Microstructural aspects of the degradation behavior of SnO2-based anodes for aluminum electrolysis |
Type |
A1 Journal article |
Year |
2010 |
Publication |
Journal of the electrochemical society |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Electrochem Soc |
Volume |
157 |
Issue |
5 |
Pages |
C178-C186 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
The performance of SnO2 ceramic anodes doped with copper and antimony oxides was examined in cryolite alumina melts under anodic polarization at different cryolite ratios, temperatures, times, and current densities. The corroded part consists of a narrow strong corrosion zone at the anode surface with damage of the intergrain contacts and a large increase in porosity, a wider moderate corrosion zone with a smaller porosity increase, and a Cu depletion zone, where the ceramic retains its initial microstructure and a slight porosity increase occurs due to the removal of the Cu-rich inclusions. Mechanical destruction of the anode was never observed in the 10100 h tests. A microstructural model of the ceramic was suggested, consisting of grains with an Sb-doped SnO2 grain core surrounded by an ~200 to 500 nm grain shell where SnO2 was simultaneously doped with Sb and Mn+ (M=Cu2+,Fe3+,Al3+). The grains were separated by a few nanometers thick Cu-enriched grain boundaries. Different secondary charge carrier (holes) concentrations and electric conductivities in the grain core and grain shell result in a higher current density at the intergrain regions that leads to their profound degradation, especially in the low temperature acidic melt. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
New York, N.Y. |
Editor |
|
Language |
|
Wos |
000276555300037 |
Publication Date |
2010-04-12 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0013-4651; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.259 |
Times cited |
3 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 3.259; 2010 IF: 2.427 |
Call Number |
UA @ lucian @ c:irua:82260 |
Serial |
2040 |
Permanent link to this record |
|
|
|
Author |
McCalla, E.; Prakash, A.S.; Berg, E.; Saubanere, M.; Abakumov, A.M.; Foix, D.; Klobes, B.; Sougrati, M.T.; Rousse, G.; Lepoivre, F.; Mariyappan, S.; Doublet, M.L.; Gonbeau, D.; Novak, P.; Van Tendeloo, G.; Hermann, R.P.; Tarascon, J.M.; |
Title |
Reversible Li-intercalation through oxygen reactivity in Li-rich Li-Fe-Te oxide materials |
Type |
A1 Journal article |
Year |
2015 |
Publication |
Journal of the electrochemical society |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Electrochem Soc |
Volume |
162 |
Issue |
162 |
Pages |
A1341-A1351 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Lithium-rich oxides are a promising class of positive electrode materials for next generation lithium-ion batteries, and oxygen plays a prominent role during electrochemical cycling either by forming peroxo-like species and/or by irreversibly forming oxygen gas during first charge. Here, we present Li-Fe-Te-O materials which show a tremendous amount of oxygen gas release. This oxygen release accounts for nearly all the capacity during the first charge and results in vacancies as seen by transmission electron microscopy. There is no oxidation of either metal during charge but significant changes in their environments. These changes are particularly extreme for tellurium. XRD and neutron powder diffraction both show limited Changes during cycling and no appreciable change in lattice parameters. A density functional theory study of this material is performed and demonstrates that the holes created on some of the oxygen atoms upon oxidation are partially stabilized through the formation of shorter O-O bonds, i.e. (O-2)(n-) species which on further delithiation show a spontaneous O-2 de-coordination from the cationic network and migration to the now empty lithium layer. The rate limiting step during charge is undoubtedly the diffusion of oxygen either out along the lithium layer or via columns of oxygen atoms. (C) 2015 The Electrochemical Society. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
New York, N.Y. |
Editor |
|
Language |
|
Wos |
000355643700030 |
Publication Date |
2015-04-29 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0013-4651;1945-7111; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.259 |
Times cited |
23 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 3.259; 2015 IF: 3.266 |
Call Number |
c:irua:126445 |
Serial |
2903 |
Permanent link to this record |
|
|
|
Author |
Cheng, K.; Leys, M.; Degroote, S.; van Daele, B.; Boeykens, S.; Derluyn, J.; Germain, M.; Van Tendeloo, G.; Engelen, J.; Borghs, G. |
Title |
Flat GaN epitaxial layers grown on Si(111) by metalorganic vapor phase epitaxy using step-graded AlGaN intermediate layers |
Type |
A1 Journal article |
Year |
2006 |
Publication |
Journal of electronic materials |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Electron Mater |
Volume |
35 |
Issue |
4 |
Pages |
592-598 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Boston, Mass. |
Editor |
|
Language |
|
Wos |
000237101800016 |
Publication Date |
2007-04-16 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0361-5235;1543-186X; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
1.579 |
Times cited |
102 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 1.579; 2006 IF: 1.504 |
Call Number |
UA @ lucian @ c:irua:58238 |
Serial |
1223 |
Permanent link to this record |
|
|
|
Author |
Zhang, F.; Vanmeensel, K.; Inokoshi, M.; Batuk, M.; Hadermann, J.; Van Meerbeek, B.; Naert, I.; Vleugels, J. |
Title |
3Y-TZP ceramics with improved hydrothermal degradation resistance and fracture toughness |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Journal of the European Ceramic Society |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Eur Ceram Soc |
Volume |
34 |
Issue |
10 |
Pages |
2453-2463 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Different factors such as the way of incorporating the Y2O3 stabilizer, alumina addition and sintering temperature were assessed with the goal to improve the low temperature degradation (LTD) resistance of 3Y-TZP without compromising on the mechanical properties. The degradation of hydrothermally treated specimens was studied by X-ray diffraction, micro-Raman spectroscopy and scanning electron microscopy. Decreasing the sintering temperature decreased the LTD susceptibility of 3Y-TZPs but did not allow to obtain a LTD resistant 3Y-TZP with optimized mechanical properties. Alumina addition along with the use of Y2O3 stabilizer coated starting powder allowed to combine both an excellent toughness and LTD resistance, as compared to alumina-free and stabilizer co-precipitated powder based equivalents. Transmission electron microscopy revealed that the improved LTD resistance could be attributed to the segregation of Al3+ at the grain boundary and the heterogeneously distributed Y3+ stabilizer. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Barking |
Editor |
|
Language |
|
Wos |
000336352500033 |
Publication Date |
2014-03-07 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0955-2219; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.411 |
Times cited |
48 |
Open Access |
|
Notes |
Fwo G.0431.10n |
Approved |
Most recent IF: 3.411; 2014 IF: 2.947 |
Call Number |
UA @ lucian @ c:irua:117065 c:irua:117065 |
Serial |
11 |
Permanent link to this record |
|
|
|
Author |
Zhang, F.; Vanmeensel, K.; Inokoshi, M.; Batuk, M.; Hadermann, J.; Van Meerbeek, B.; Naert, I.; Vleugels, J. |
Title |
Critical influence of alumina content on the low temperature degradation of 2-3 mol% yttria-stabilized TZP for dental restorations |
Type |
A1 Journal article |
Year |
2015 |
Publication |
Journal of the European Ceramic Society |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Eur Ceram Soc |
Volume |
35 |
Issue |
35 |
Pages |
741-750 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
The influence of 0.25, 2 and 5 wt.% alumina addition on the mechanical properties and low temperature degradation (LTD) of 3, 2.5 and 2 mol% yttria-stabilized TZP ceramics was investigated. The amount of alumina addition was observed to have a crucial impact on the degradation of Y-TZP ceramics. Independent on the yttria stabilizer content, 0.25 wt.% alumina had a higher degradation retarding effect to Y-TZP ceramics than 2 and 5 wt.% of alumina addition, which had a comparable effect. The apparent activation energy for the degradation process was increased by adding alumina, but it was the same for 0.255 wt.% alumina doped 3Y-TZP ceramics. For Y-TZPs containing a small amount of alumina addition, only the segregated Al3+ at the grain boundaries of the zirconia grains was effective to retard the degradation of Y-TZPs. The secondary phase Al2O3 grains increased the degradation kinetics, which might be attributed to the residual stresses. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Barking |
Editor |
|
Language |
|
Wos |
000345201700032 |
Publication Date |
2014-09-27 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0955-2219; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.411 |
Times cited |
37 |
Open Access |
|
Notes |
Fwo G043110n |
Approved |
Most recent IF: 3.411; 2015 IF: 2.947 |
Call Number |
c:irua:121328 |
Serial |
544 |
Permanent link to this record |
|
|
|
Author |
Van Tendeloo, G.; Krekels, T. |
Title |
HREM of ceramic high Tc superconductors |
Type |
A1 Journal article |
Year |
1996 |
Publication |
Journal of the European Ceramic Society |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Eur Ceram Soc |
Volume |
16 |
Issue |
|
Pages |
367-378 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Barking |
Editor |
|
Language |
|
Wos |
A1996UC80200005 |
Publication Date |
2002-07-25 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0955-2219; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.947 |
Times cited |
1 |
Open Access |
|
Notes |
|
Approved |
no |
Call Number |
UA @ lucian @ c:irua:16861 |
Serial |
1507 |
Permanent link to this record |
|
|
|
Author |
Xu, T.; Wang, P.; Fang, P.; Kan, Y.; Chen, L.; Vleugels, J.; Van der Biest, O.; van Landuyt, J. |
Title |
Phase assembly and microstructure of CeO2-doped ZrO2 ceramics prepared by spark plasma sintering |
Type |
A1 Journal article |
Year |
2005 |
Publication |
Journal of the European Ceramic Society |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Eur Ceram Soc |
Volume |
25 |
Issue |
15 |
Pages |
3437-3442 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
CeO2-doped ZrO2, (8 mol%) starting powder was sintered by means of spark plasma sintering (SPS) at 1300 degrees C without holding time. The stability of the tetragonal ZrO2 phase in the Ce-ZrO2 ceramic sintered under strongly reducing conditions was investigated. The SPS sample consisted of monoclinic and tetragonal ZrO2 phase, with a volume ratio of two to one, as well as a trace amount of a Zr-Ce-O cubic solid solution phase. In contrast, the same powder sintered by hot-pressing in nitrogen at 1300 and 1500 degrees C for 1h showed no tetragonal ZrO2. Microstructural observation of the SPS ceramic by SEM and TEM revealed grains with and without twins. The reason for the appearance of the tetragonal phase in the SPS sample sintered under strongly reducing conditions is discussed. (c) 2004 Elsevier Ltd. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Barking |
Editor |
|
Language |
|
Wos |
000232172100006 |
Publication Date |
2004-12-16 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0955-2219; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.411 |
Times cited |
13 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 3.411; 2005 IF: 1.567 |
Call Number |
UA @ lucian @ c:irua:104065 |
Serial |
2576 |
Permanent link to this record |
|
|
|
Author |
Prituzhalov, V.A.; Ardashnikova, E.I.; Vinogradov, A.A.; Dolgikh, V.A.; Videau, J.-J.; Fargin, E.; Abakumov, A.M.; Tarakina, N.V.; Van Tendeloo, G. |
Title |
New anion-conducting solid solutions Bi1-xTex(O,F)2+\delta (x > 0.5) and glassceramic material on their base |
Type |
A1 Journal article |
Year |
2011 |
Publication |
Journal of fluorine chemistry |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Fluorine Chem |
Volume |
132 |
Issue |
12 |
Pages |
1110-1116 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
The anion-excess fluorite-like solid solutions with general composition Bi1−xTex(O,F)2+δ (x > 0.5) have been synthesized by a solid state reaction of TeO2, BiF3 and Bi2O3 at 873 K with following quenching. The homogeneity areas and polymorphism of the I ↔ IV Bi1−xTex(O,F)2+δ phases were investigated. The crystal structure of the low temperature IV-Bi1−xTex(O,F)2+δ phase has been solved using electron diffraction and X-ray powder diffraction (a = 11.53051(9) Å, S.G. Ia-3, RI = 0.046, RP = 0.041). Glass formation area in the Bi2O3BiF3TeO2 (10% TiO2) system was investigated. IVBi1−xTex(O,F)2+δ phase starts to crystallize at short-time (0.53 h) annealing of oxyfluoride glasses at temperatures above Tg (600615 K). The ionic conductivity of the crystalline Bi1−xTex(O,F)2+δ phase and corresponding glass-ceramics was investigated. Activation energy of conductivity Ea = 0.41(2) eV for the IV-Bi1−xTex(O,F)2+δ crystalline samples and Ea = 0.73 eV for the glass-ceramic samples were obtained. Investigation of the oxyfluoride samples with a constant cation ratio demonstrates essential influence of excess fluorine anions on the ionic conductivity. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
000296936300011 |
Publication Date |
2011-07-07 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0022-1139; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.101 |
Times cited |
2 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 2.101; 2011 IF: 2.033 |
Call Number |
UA @ lucian @ c:irua:93687 |
Serial |
2305 |
Permanent link to this record |
|
|
|
Author |
Idrissi, H.; Samaee, V.; Lumbeeck, G.; Werf, T.; Pardoen, T.; Schryvers, D.; Cordier, P. |
Title |
In Situ Quantitative Tensile Testing of Antigorite in a Transmission Electron Microscope |
Type |
A1 Journal article |
Year |
2020 |
Publication |
Journal Of Geophysical Research-Solid Earth |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Geophys Res-Sol Ea |
Volume |
125 |
Issue |
3 |
Pages |
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
The determination of the mechanical properties of serpentinites is essential toward the understanding of the mechanics of faulting and subduction. Here we present the first in situ tensile tests on antigorite in a transmission electron microscope. A push‐to‐pull deformation device is used to perform quantitative tensile tests, during which force and displacement are measured, while the evolving microstructure is imaged with the microscope. The experiments have been performed at room temperature on 2 × 1 × 0.2 μm3 beams prepared by focused ion beam. The specimens are not single crystals despite their small sizes. Orientation mapping indicated that several grains were well oriented for plastic slip. However, no dislocation activity has been observed even though the engineering tensile stress went up to 700 MPa. We show also that antigorite does not exhibit a purely elastic‐brittle behavior since, despite the presence of defects, the specimens accumulate permanent deformation and did not fail within the elastic regime. Instead, we observe that strain localizes at grain boundaries. All observations concur to show that under these experimental conditions, grain boundary sliding is the dominant deformation mechanism. This study sheds a new light on the mechanical properties of antigorite and calls for further studies on the structure and properties of grain boundaries in antigorite and more generally in phyllosilicates. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000530895800023 |
Publication Date |
2020-02-20 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
2169-9313 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.9 |
Times cited |
|
Open Access |
OpenAccess |
Notes |
We thank S. Guillot for having kindly provided us with the two antigorite samples investigated in this study. We acknowledge funding from the European Research Council (ERC) under the European Union's Horizon 2020 research and innovation program under Grant Agreement 787198—TimeMan. H. Idrissi is mandated by the Belgian National Fund for Scientific Research (FSR‐FNRS). We acknowledge fruitful discussions with A. Baronnet. We thank J. Gasc and an anonymous reviewer for their critical comments. Data (movies of the three in situ deformation experiments) can be downloaded (from https://doi.org/10.5281/zenodo.3583135). |
Approved |
Most recent IF: 3.9; 2020 IF: 3.35 |
Call Number |
EMAT @ emat @c:irua:167594 |
Serial |
6355 |
Permanent link to this record |
|
|
|
Author |
Esquivel, D.; Ouwehand, J.; Meledina, M.; Turner, S.; Tendeloo, G.V.; Romero-Salguero, F.J.; Clercq, J.D.; Voort, P.V.D. |
Title |
Thiol-ethylene bridged PMO: A high capacity regenerable mercury adsorbent via intrapore mercury thiolate crystal formation |
Type |
A1 Journal article |
Year |
2017 |
Publication |
Journal of hazardous materials |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Hazard Mater |
Volume |
339 |
Issue |
339 |
Pages |
368-377 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Highly ordered thiol-ethylene bridged Periodic Mesoporous Organosilicas were synthesized directly from a homemade thiol-functionalized bis-silane precursor. These high surface area materials contain up to 4.3 mmol/g sulfur functions in the walls and can adsorb up to 1183 mg/g mercury ions. Raman spectroscopy reveals the existence of thiol and disulfide moieties. These groups have been evaluated by a combination of Raman spectroscopy, Ellman’s reagent and elemental analysis. The adsorption of mercury ions was evidenced by different techniques, including Raman, XPS and porosimetry, which indicate that thiol groups are highly accessible to mercury. Scanning transmission electron microscopy combined with EDX showed an even homogenous distribution of the sulfur atoms throughout the structure, and have revealed for the first time that a fraction of the adsorbed mercury is forming thiolate nanocrystals in the pores. The adsorbent is highly selective for mercury and can be regenerated and reused multiple times, maintaining its structure and functionalities and showing only a marginal loss of adsorption capacity after several runs. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000407188200040 |
Publication Date |
2017-06-22 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0304-3894 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
6.065 |
Times cited |
12 |
Open Access |
OpenAccess |
Notes |
D.E. thanks the F.W.O. Flanders (Fund Scientific Research) for a postdoctoral grant (3E10813W). J.O. acknowledges also F.W.O. Flanders, research project G006813N, and the research Board of Ghent University, UGent GOA (Concerted Research Actions) (grant 01G00710) for financial support. F. J. R.-S. acknowledges funding of this research by the Spanish Ministry of Economy and Competitiveness (Project MAT2013-44463-R), Andalusian Regional Government (FQM-346 group), and Feder Funds. The Titan microscope used for this investigation was partially funded by the Hercules foundation of the Flemish government. This work was supported by the Belgian IAP-PAI network. |
Approved |
Most recent IF: 6.065 |
Call Number |
EMAT @ emat @ c:irua:144433 |
Serial |
4624 |
Permanent link to this record |
|
|
|
Author |
De Decker, J.; Folens, K.; De Clercq, J.; Meledina, M.; Van Tendeloo, G.; Du Laing, G.; Van Der Voort, P. |
Title |
Ship-in-a-bottle CMPO in MIL-101(Cr) for selective uranium recovery from aqueous streams through adsorption |
Type |
A1 Journal article |
Year |
2017 |
Publication |
Journal of hazardous materials |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Hazard Mater |
Volume |
335 |
Issue |
|
Pages |
1-9 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Mesoporous MIL-101(Cr) is used as host for a ship-in-a-bottle type adsorbent for selective U(VI) recovery from aqueous environments. The acid-resistant cage-type MOF is built in-situ around N,N-Diisobutyl-2-(octylphenylphosphoryl)acetamide (CMPO), a sterically demanding ligand with high U(VI) affinity. This one-step procedure yields an adsorbent which is an ideal compromise between homogeneous and heterogeneous systems, where the ligand can act freely within the pores of MIL-101, without leaching, while the adsorbent is easy separable and reusable. The adsorbent was characterized by XRD, FTIR spectroscopy, nitrogen adsorption, XRF, ADF-STEM and EDX, to confirm and quantify the successful encapsulation of the CMPO in MIL-101, and the preservation of the host. Adsorption experiments with a central focus on U(VI) recovery were performed. Very high selectivity for U(VI) was observed, while competitive metal adsorption (rare earths, transition metals...) was almost negligible. The adsorption capacity was calculated at 5.32 mg U/g (pH 3) and 27.99 mg U/g (pH 4), by fitting equilibrium data to the Langmuir model. Adsorption kinetics correlated to the pseudo-second-order model, where more than 95% of maximum uptake is achieved within 375 min. The adsorbed U(VI) is easily recovered by desorption in 0.1 M HNO3. Three adsorption/desorption cycles were performed. (C) 2017 Elsevier B.V. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
Language |
|
Wos |
000402948600001 |
Publication Date |
2017-04-09 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0304-3894 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
6.065 |
Times cited |
35 |
Open Access |
OpenAccess |
Notes |
; The authors acknowledge the AUGent/UGent for financial support, Grant Number DEF12/AOP/008 fund IV1. ; |
Approved |
Most recent IF: 6.065 |
Call Number |
UA @ lucian @ c:irua:144153 |
Serial |
4685 |
Permanent link to this record |
|
|
|
Author |
Leus, K.; Folens, K.; Nicomel, N.R.; Perez, J.P.H.; Filippousi, M.; Meledina, M.; Dirtu, M.M.; Turner, S.; Van Tendeloo, G.; Garcia, Y.; Du Laing, G.; Van Der Voort, P. |
Title |
Removal of arsenic and mercury species from water by covalent triazine framework encapsulated \gamma-Fe2O3 nanoparticles |
Type |
A1 Journal article |
Year |
2018 |
Publication |
Journal of hazardous materials |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Hazard Mater |
Volume |
353 |
Issue |
353 |
Pages |
312-319 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
The covalent triazine framework, CTF-1, served as host material for the in situ synthesis of Fe2O3 nanoparticles. The composite material consisted of 20 +/- 2 m% iron, mainly in gamma-Fe2O3 phase. The resulting gamma-Fe2O3@CTF-1 was examined for the adsorption of As-III, As-V and H-II from synthetic solutions and real surface-, ground- and wastewater. The material shows excellent removal efficiencies, independent from the presence of Ca2+, Mg2+ or natural organic matter and only limited dependency on the presence of phosphate ions. Its adsorption capacity towards arsenite (198.0 mg g(-1)), arsenate (102.3 mg g(-1)) and divalent mercury (165.8 mg g(-1)) belongs amongst the best-known adsorbents, including many other iron-based materials. Regeneration of the adsorbent can be achieved for use over multiple cycles without a decrease in performance by elution at 70 degrees C with 0.1 M NaOH, followed by a stirring step in a 5 m% H2O2 solution for As or 0.1 M thiourea and 0.001 M HCl for Hg. In highly contaminated water (100 mu gL(-1)), the adsorbent polishes the water quality to well below the current WHO limits. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
Language |
|
Wos |
000438002800035 |
Publication Date |
2018-04-16 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0304-3894 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
6.065 |
Times cited |
22 |
Open Access |
OpenAccess |
Notes |
; Karen Leus acknowledges financial support from Ghent University. Nina Ricci Nicomel and Jeffrey Paulo H. Perez thank the funding of the VLIR-UOS. Marinela M. Dirtu acknowledges F.R.S.-FNRS for a Charge de recherches position. Stuart Turner gratefully acknowledges the FWO Vlaanderen for a post-doctoral scholarship. The Titan microscope used for this investigation was partially funded by the Hercules foundation of the Flemish government. This work was supported by the Belgian IAP-PAI network. ; |
Approved |
Most recent IF: 6.065 |
Call Number |
UA @ lucian @ c:irua:152430 |
Serial |
5124 |
Permanent link to this record |
|
|
|
Author |
Buschmann, V.; Schryvers, D.; van Landuyt, J.; van Roost, C.; de Keyzer, R. |
Title |
A comparative investigation of replication techniques used for the study of (S+Au) sensitized AgBr microcrystals |
Type |
A1 Journal article |
Year |
1996 |
Publication |
The journal of imaging science and technology |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Imaging Sci Techn |
Volume |
40 |
Issue |
|
Pages |
189-201 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Springfield, Va |
Editor |
|
Language |
|
Wos |
A1996VL09200003 |
Publication Date |
0000-00-00 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1062-3701 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
0.349 |
Times cited |
4 |
Open Access |
|
Notes |
|
Approved |
MATERIALS SCIENCE, MULTIDISCIPLINARY 135/271 Q2 # PHYSICS, APPLIED 70/145 Q2 # PHYSICS, CONDENSED MATTER 40/67 Q3 # |
Call Number |
UA @ lucian @ c:irua:15428 |
Serial |
418 |
Permanent link to this record |
|
|
|
Author |
van Renterghem, W.; Schryvers, D.; van Landuyt, J.; van Roost, C.; de Keyzer, R. |
Title |
The influence of crystal thickness on the image tone |
Type |
A1 Journal article |
Year |
2003 |
Publication |
Journal of imaging science |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Imaging Sci Techn |
Volume |
47 |
Issue |
2 |
Pages |
133-138 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
It is known that the neutral image tone of a developed photographic film becomes brownish when the thickness of the original silver halide tabular crystals is reduced. We investigate by electron microscopy to what extent the silver filament structure has changed and how it induces the shift in image tone. Therefore, two samples of AgBr {111} tabular crystals with average thicknesses of 160 nm and 90 nm respectively, are compared. It is shown that the dimensions and defect structure of the filaments are comparable, but that the 90 nm crystals result in a more widely spaced structure, which explains the shift in image tone on a qualitative level. The influence of the addition of an image toner, i.e., phenylmercaptotetrazole, on the filament structure is also investigated. An even more open filament structure of longer, but smaller filaments was observed. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Springfield, Va |
Editor |
|
Language |
|
Wos |
|
Publication Date |
0000-00-00 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
8750-9237; 1062-3701 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
0.348 |
Times cited |
|
Open Access |
|
Notes |
|
Approved |
Most recent IF: NA |
Call Number |
UA @ lucian @ c:irua:48384 |
Serial |
1619 |
Permanent link to this record |
|
|
|
Author |
van Renterghem, W.; Goessens, C.; Schryvers, D.; van Landuyt, J.; Bollen, D.; de Keyzer, R.; van Roost, C. |
Title |
Influence of twinning on the morphology of AgBr and AgCl microcrystals |
Type |
A1 Journal article |
Year |
2001 |
Publication |
The journal of imaging science and technology |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Imaging Sci Techn |
Volume |
45 |
Issue |
|
Pages |
349-356 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Springfield, Va |
Editor |
|
Language |
|
Wos |
|
Publication Date |
0000-00-00 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1062-3701 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
0.348 |
Times cited |
|
Open Access |
|
Notes |
|
Approved |
Most recent IF: 0.348; 2001 IF: NA |
Call Number |
UA @ lucian @ c:irua:48381 |
Serial |
1657 |
Permanent link to this record |
|
|
|
Author |
Potapov, P.L.; Schryvers, D.; Strijckers, H.; van Roost, C. |
Title |
Microstructural mechanism of development in photothermographic materials |
Type |
A1 Journal article |
Year |
2003 |
Publication |
The journal of imaging science and technology |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Imaging Sci Techn |
Volume |
47 |
Issue |
2 |
Pages |
115-123 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Springfield, Va |
Editor |
|
Language |
|
Wos |
|
Publication Date |
0000-00-00 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1062-3701 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
0.348 |
Times cited |
|
Open Access |
|
Notes |
|
Approved |
Most recent IF: 0.348; 2003 IF: NA |
Call Number |
UA @ lucian @ c:irua:48382 |
Serial |
2046 |
Permanent link to this record |
|
|
|
Author |
Goessens, C.; Schryvers, D.; van Landuyt, J.; de Keyzer, R. |
Title |
New method to determine the parity of the number of twin planes in tabular silver halide microcrystals from top views |
Type |
A1 Journal article |
Year |
1997 |
Publication |
The journal of imaging science and technology |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Imaging Sci Techn |
Volume |
41 |
Issue |
|
Pages |
301-307 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Springfield, Va |
Editor |
|
Language |
|
Wos |
000077457600017 |
Publication Date |
0000-00-00 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1062-3701 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
0.348 |
Times cited |
1 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 0.348; 1997 IF: NA |
Call Number |
UA @ lucian @ c:irua:21346 |
Serial |
2324 |
Permanent link to this record |
|
|
|
Author |
van Renterghem, W.; Schryvers, D.; van Landuyt, J.; Bollen, D.; van Roost, C.; de Keyzer, R. |
Title |
A TEM study of non-parallel twins inducing thickness growth in silver chloride {111} tabular crystals |
Type |
A1 Journal article |
Year |
2001 |
Publication |
The journal of imaging science and technology |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Imaging Sci Techn |
Volume |
45 |
Issue |
|
Pages |
83-90 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Springfield, Va |
Editor |
|
Language |
|
Wos |
|
Publication Date |
0000-00-00 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1062-3701 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
0.348 |
Times cited |
|
Open Access |
|
Notes |
|
Approved |
Most recent IF: 0.348; 2001 IF: NA |
Call Number |
UA @ lucian @ c:irua:48380 |
Serial |
3490 |
Permanent link to this record |
|
|
|
Author |
Khalil-Allafi, J.; Amin-Ahmadi, B. |
Title |
Effect of mold hardness on microstructure and contraction porosity in ductile cast iron |
Type |
A1 Journal article |
Year |
2011 |
Publication |
Journal of iron and steel research international |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Iron Steel Res Int |
Volume |
18 |
Issue |
4 |
Pages |
44-47 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
The effect of mold hardness on the microstructure of ductile iron and the contraction porosity was investigated. Molds with different hardnesses (0.41, 0.48, 0.55, 0.62 MPa) and a sand mold prepared by Co2 method were used. The influence of silicon content on the induced expansion pressure owing to the formation of graphite was also investigated. The contraction during solidification can be compensated by an induced expansion owing to the graphite relief when the hardness of mold increases; therefore, the possibility of achieving a sound product without using any riser increases. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
|
Publication Date |
2011-05-01 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1006-706X; |
ISBN |
|
Additional Links |
UA library record |
Impact Factor |
0.836 |
Times cited |
1 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 0.836; 2011 IF: 0.213 |
Call Number |
UA @ lucian @ c:irua:122044 |
Serial |
823 |
Permanent link to this record |
|
|
|
Author |
Khalil-Allafi, J.; Amin-Ahmadi, B. |
Title |
Influence of mold preheating and silicon content on microstructure and casting properties of ductile iron in permanent mold |
Type |
A1 Journal article |
Year |
2011 |
Publication |
Journal of iron and steel research international |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Iron Steel Res Int |
Volume |
18 |
Issue |
3 |
Pages |
34-39 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
The effects of the mold preheating and the silicon content of ductile iron on the percentage of carbides, graphite nodule counts and shrinkage volume were investigated. The results showed that the percentage of carbides and the shrinkage volume decreased when the mold preheating increased. The ductile iron with the carbon equivalent of 4.45% and the silicon content of 2.5% without any porosity defects was achieved when the mold preheating was 450 °C. Increasing the silicon content in the range of 2.1%3.3% led to the increase in graphite nodule count and graphite size and the decrease in percentage of carbides. It is due to the increase in induced expansion pressure during the graphite formation with the increasing of silicon content. The suitable condition for casting a sound product of ductile iron without the riser at the mold preheating temperature of 300 °C is the silicon content of 3.3% and carbon equivalent of 4.7%. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
|
Publication Date |
2011-03-28 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1006-706X; |
ISBN |
|
Additional Links |
UA library record |
Impact Factor |
0.836 |
Times cited |
3 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 0.836; 2011 IF: 0.213 |
Call Number |
UA @ lucian @ c:irua:122043 |
Serial |
1629 |
Permanent link to this record |
|
|
|
Author |
Antipov, E.V.; Khasanova, N.R.; Pshirkov, J.S.; Putilin, S.N.; Bougerof, C.; Lebedev, O.I.; Van Tendeloo, G.; Baranov, A.; Park, Y.W. |
Title |
The superconducting bismuth-based mixed oxides |
Type |
A1 Journal article |
Year |
2003 |
Publication |
Journal of low temperature physics
T2 – International Conference on Physics and Chemistry of Molecular and Oxide, Superconductors (MOS2002), AUG 13-18, 2002, HSINCHU, TAIWAN |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Low Temp Phys |
Volume |
131 |
Issue |
3-4 |
Pages |
575-587 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
The present paper describes the synthesis, characterization of mixed-valence bismuthates with 3- or 2-dimensional perovskite-like structures and structural criteria that influence superconductivity in these compounds. Single-phase samples of Sr1-xKxBiO3 were prepared for the broad range of K-content: 0.25 less than or equal to x less than or equal to 0.65. For these bismuthates the symmetry of the structure changes from monoclinic to orthorhombic and finally to tetragonal upon increasing the K-content thus resulting in the decrease of the Bi-O distances and reduction of the network distortions. Superconductivity with maximum T-c = 12K exists in the narrow range (x approximate to 0.5 – 0.6) within the stability field of the tetragonal phase (0.33 less than or equal to x less than or equal to 0.65), when the 3-dimensional octahedral framework has close to the ideal perovskite structure arrangement. At the same time compositions with close to optimal Bi-valence (x = 0.33 and 0.43) do not show any sign of superconductivity, probably, due to structural distortions. The layered type (BaK)(3)Bi2O7 and (Ba,K)(2)BiO4 bismuthates belonging to the A(n+1)B(n)O(3n+1) homologous series were investigated Buckling of the (BiO2) layers in the structure of the n = 2 member was revealed The formation of the n=1 bismuthate was found by Electron Microscopy and X-ray powder diffraction studies. Both types of compounds are considered to be possible candidates for new superconducting materials among bismuthates. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
New York |
Editor |
|
Language |
|
Wos |
000181768000061 |
Publication Date |
2003-04-07 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0022-2291; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
1.3 |
Times cited |
3 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 1.3; 2003 IF: 1.171 |
Call Number |
UA @ lucian @ c:irua:102803 |
Serial |
3597 |
Permanent link to this record |
|
|
|
Author |
Van Tendeloo, G.; Lebedev, O.I.; Amelinckx, S. |
Title |
Atomic and microstructure of CMR materials |
Type |
A1 Journal article |
Year |
2000 |
Publication |
Journal of magnetism and magnetic materials |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Magn Magn Mater |
Volume |
211 |
Issue |
|
Pages |
73-83 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
Language |
|
Wos |
000085772100013 |
Publication Date |
2002-07-25 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0304-8853; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.63 |
Times cited |
48 |
Open Access |
|
Notes |
Iuap 4-10 |
Approved |
Most recent IF: 2.63; 2000 IF: 0.996 |
Call Number |
UA @ lucian @ c:irua:54773 |
Serial |
165 |
Permanent link to this record |
|
|
|
Author |
Khazzan, S.; Bessais, L.; Van Tendeloo, G.; Mliki, N. |
Title |
Correlation between the nanocrystalline Sm(Fe,Mo)12 and its out of equilibrium phase Sm(Fe,Mo)10 |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Journal of magnetism and magnetic materials |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Magn Magn Mater |
Volume |
363 |
Issue |
|
Pages |
125-132 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Nanostructured Sm-Fe-Mo semi-hard magnetic material exhibiting enhanced magnetic properties can be produced by ball milling followed by recrystallization. Milled samples were annealed for 30 min in a vacuum at different temperatures (T-A) between 700 and 1190 degrees C. The effects of heat treatment and Mo content on structural and magnetic property changes have been investigated by means of X-ray diffraction using the Rietvekl method, transmission electron microscopy and magnetic measurements. For samples annealed at T-A > 900 degrees C the tetragonal ThMn12-type structure is identified, while for 700 < T-A < 900 degrees C a new out of equilibrium P6/mmm type structure was found as the major phase. This novel nanocrystalline phase has never been synthesized before. The correspondent stoichiometry is determined on the basis of the vacancy model. The Rietveld analysis gives a stoichiometry ratio equal to 1:10, for the out of equilibrium hexagonal phase, which is described with three crystallographic transition metal sites: 3g is fully occupied, 61 occupation is limited to hexagons surrounding the Fe dumbbell pairs 2e. We have performed a magnetic and structural study of nanocrystalline metastable P6/mrnm Sm(Fe1-xMo)(10), correlated with structural transformation towards its equilibrium derivative 14/mrnm Sm(Fe1-xMo)(12). A maximum of the coercive field H-C (H-C > 5 kOe) has been observed for the new hexagonal P6/rnmm phase suggesting that nanocrystalline Sm(Fe,Mo)(10), is a semi hard material, and is potential candidate for magnetic recording. (C) 2014 Elsevier B.V. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
Language |
|
Wos |
000335393900021 |
Publication Date |
2014-04-05 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0304-8853; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.63 |
Times cited |
6 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 2.63; 2014 IF: 1.970 |
Call Number |
UA @ lucian @ c:irua:117139 |
Serial |
524 |
Permanent link to this record |
|
|
|
Author |
Angelakeris, M.; Li, Z.A.; Hilgendorff, M.; Simeonidis, K.; Sakellari, D.; Filippousi, M.; Tian, H.; Van Tendeloo, G.; Spasova, M.; Acet, M.; Farle, M. |
Title |
Enhanced biomedical heat-triggered carriers via nanomagnetism tuning in ferrite-based nanoparticles |
Type |
A1 Journal article |
Year |
2015 |
Publication |
Journal of magnetism and magnetic materials |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Magn Magn Mater |
Volume |
381 |
Issue |
381 |
Pages |
179-187 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Biomedical nanomagnetic carriers are getting a higher impact in therapy and diagnosis schemes while their constraints and prerequisites are more and more successfully confronted. Such particles should possess a well-defined size with minimum agglomeration and they should be synthesized in a facile and reproducible high-yield way together with a controllable response to an applied static or dynamic field tailored for the specific application. Here, we attempt to enhance the heating efficiency in magnetic particle hyperthermia treatment through the proper adjustment of the core-shell morphology in ferrite particles, by controlling exchange and dipolar magnetic interactions at the nanoscale. Thus, core-shell nanoparticles with mutual coupling of magnetically hard (CoFe2O4) and soft (MnFe2O4) components are synthesized with facile synthetic controls resulting in uniform size and shell thickness as evidenced by high resolution transmission electron microscopy imaging, excellent crystallinity and size monodispersity. Such a magnetic coupling enables the fine tuning of magnetic anisotropy and magnetic interactions without sparing the good structural, chemical and colloidal stability. Consequently, the magnetic heating efficiency of CoFe2O4. and MnFe2O4 core-shell nanoparticles is distinctively different horn that of their counterparts, even though all these nanocrystals were synthesized under similar conditions. For better understanding of the AC magnetic hyperthermia response and its correlation with magnetic-origin features we study the effect of the volume ratio of magnetic hard and soft phases in the bimagnetic core-shell nanocrystals. Eventually, such particles may be considered as novel heating carriers that under further biomedical functionalization may become adaptable multifunctional heat-triggered nanoplatforms. (C) 2014 Elsevier B.V. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
Language |
|
Wos |
000349361100027 |
Publication Date |
2014-12-29 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0304-8853; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.63 |
Times cited |
20 |
Open Access |
|
Notes |
312483 Esteem2; Esteem2_ta |
Approved |
Most recent IF: 2.63; 2015 IF: 1.970 |
Call Number |
c:irua:125284 c:irua:125284 |
Serial |
1049 |
Permanent link to this record |
|
|
|
Author |
Schuddinck, W.; Van Tendeloo, G.; Barnabé, A.; Hervieu, M.; Raveau, B. |
Title |
Relation between structure, charge ordering and magnetotransport properties in Nd0.5Ca0.5Mn1-xCrxO3 manganites |
Type |
A1 Journal article |
Year |
2000 |
Publication |
Journal of magnetism and magnetic materials
T2 – Symposium G Material Physics Issues and Applications of Magnetic Oxides, at the E-MRS Spring Meeting, JUN 01-04, 1999, Strasbourg, France |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Magn Magn Mater |
Volume |
211 |
Issue |
1-3 |
Pages |
105-110 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
The relationships between incommensurability, charge ordering and magnetotransport properties in Nd0.5Ca0.5Mn1-xCrxO3 manganites have been studied by electron diffraction and lattice imaging versus temperature with 0.02 less than or equal to x less than or equal to 0.07. All compositions show an incommensurate superstructure over the whole temperature domain, despite the fact that they are ferromagnetic and conductive below 140 K, The q-vector (1/2 – delta)a* decreases with increasing temperature for all compositions x. For a given temperature q also decreases with x. Lattice images obtained at low temperature give a clear view of the characteristics of the incommensurate structure. They also provide a better understanding of the charge ordering process. The low-temperature form of the Cr-doped manganites is not a perfectly doubled cell [[2a(p)root 2 x 2a(p) x a(p)root 2]], but defects inducing a tripled cell occur pseudo-periodically. (C) 2000 Elsevier Science B.V. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
Language |
|
Wos |
000085772100017 |
Publication Date |
2002-07-25 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0304-8853; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.63 |
Times cited |
16 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 2.63; 2000 IF: 0.996 |
Call Number |
UA @ lucian @ c:irua:104256 |
Serial |
2858 |
Permanent link to this record |
|
|
|
Author |
Jacobs, W.; Reynaerts, C.; Andries, S.; van den Akker, S.; Moonen, N.; Lamoen, D. |
Title |
Analyzing the dispersion of cargo vapors around a ship’s superstructure by means of wind tunnel experiments |
Type |
A1 Journal article |
Year |
2016 |
Publication |
Journal of marine science and technology |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Mar Sci Tech-Japan |
Volume |
21 |
Issue |
21 |
Pages |
758-766 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
In a previous study, it was found that cargo tank operations like cleaning and venting, lead to higher cargo vapor concentrations around the ship’s superstructure. Can wind tunnel experiments confirm these findings? Is there an improvement when using higher outlets at high velocities compared to lower outlets with a low outlet velocity? Is there a relation between relative wind speed and measured concentration? These questions were investigated in the Peutz wind tunnel. By using a tracer gas for the wind tunnel experiments, concentration coefficients have been calculated for various settings. The study shows that using high-velocity outlets is an efficient way to keep concentrations as low as possible. The only exception is for relative wind directions from the bow. In this last case using a manhole as ventilation outlet leads to lower concentrations. With increasing wind speeds the building downwash effect resulted in higher concentration coefficients near the main deck. This study confirms our on-board measurements and suggests the lowering of the ventilation inlet of the accommodation, so that the high-velocity outlet can be used safely at all times. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000388260200015 |
Publication Date |
2016-05-21 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0948-4280 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
0.838 |
Times cited |
2 |
Open Access |
|
Notes |
The authors would like to thank Peutz bv. at Molenhoek, the Netherlands, for providing the wind tunnel facilities and their assistance during the various stages of this research. |
Approved |
Most recent IF: 0.838 |
Call Number |
EMAT @ emat @ c:irua:138728 |
Serial |
4326 |
Permanent link to this record |
|
|
|
Author |
Hadermann, J.; Pérez, O.; Créon, N.; Michel, C.; Hervieu, M. |
Title |
The (3 + 2)D structure of oxygen deficient LaSrCuO3.52 |
Type |
A1 Journal article |
Year |
2007 |
Publication |
Journal of materials chemistry |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Mater Chem |
Volume |
17 |
Issue |
22 |
Pages |
2344-2350 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Cambridge |
Editor |
|
Language |
|
Wos |
000247349400020 |
Publication Date |
2007-04-18 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0959-9428;1364-5501; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
7 |
Open Access |
|
Notes |
Supergmr:Hprn-Ct-2000-0021 |
Approved |
Most recent IF: NA |
Call Number |
UA @ lucian @ c:irua:64749 c:irua:64749 |
Serial |
13 |
Permanent link to this record |
|
|
|
Author |
Van Tendeloo, G.; Hadermann, J.; Abakumov, A.M.; Antipov, E.V. |
Title |
Advanced electron microscopy and its possibilities to solve complex structures: application to transition metal oxides |
Type |
A1 Journal article |
Year |
2009 |
Publication |
Journal of materials chemistry |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Mater Chem |
Volume |
19 |
Issue |
18 |
Pages |
2660-2670 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Design and optimization of materials properties can only be performed through a thorough knowledge of the structure of the compound. In this feature article we illustrate the possibilities of advanced electron microscopy in materials science and solid state chemistry. The different techniques are briefly discussed and several examples are given where the structures of complex oxides, often with a modulated structure, have been solved using electron microscopy. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Cambridge |
Editor |
|
Language |
|
Wos |
000265740600002 |
Publication Date |
2009-02-04 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0959-9428;1364-5501; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
9 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: NA |
Call Number |
UA @ lucian @ c:irua:77065 |
Serial |
68 |
Permanent link to this record |
|
|
|
Author |
Narayanan, V.; Lommens, P.; De Buysser, K.; Vanpoucke, D.E.P.; Huehne, R.; Molina, L.; Van Tendeloo, G.; van der Voort, P.; Van Driessche, I. |
Title |
Aqueous CSD approach for the growth of novel, lattice-tuned LaxCe1-xO\delta epitaxial layers |
Type |
A1 Journal article |
Year |
2012 |
Publication |
Journal of materials chemistry |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Mater Chem |
Volume |
22 |
Issue |
17 |
Pages |
8476-8483 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Lanthanumcerium oxide (LCO) films were deposited on Ni-5%W substrates by chemical solution deposition (CSD) from water-based precursors. LCO films containing different ratios of lanthanum and cerium ions (from CeO2 to La2Ce2O7) were prepared. The composition of the layers was optimized towards the formation of LCO buffer layers, lattice-matched with the superconducting YBa2Cu3Oy layer, useful for the development of coated conductors. Single, crack-free LCO layers with a thickness of up to 140 nm could be obtained in a single deposition step. The crystallinity and microstructure of these lattice-matched LCO layers were studied by X-ray diffraction techniques, RHEED and SEM. We find that only layers with thickness below 100 nm show a crystalline top surface although both thick and thin layers show good biaxial texture in XRD. On the most promising layers, AFM and (S)TEM were performed to further evaluate their morphology. The overall surface roughness varies between 3.9 and 7.5 nm, while the layers appear much more dense than the frequently used La2Zr2O7 (LZO) systems, showing much smaller nanovoids (12 nm) than the latter system. Their effective buffer layer action was studied using XPS. The thin LCO layers supported the growth of superconducting YBCO deposited using PLD methods. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Cambridge |
Editor |
|
Language |
|
Wos |
000302367500044 |
Publication Date |
2012-03-20 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0959-9428;1364-5501; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
24 |
Open Access |
|
Notes |
Iap |
Approved |
Most recent IF: NA |
Call Number |
UA @ lucian @ c:irua:96960 |
Serial |
148 |
Permanent link to this record |
|
|
|
Author |
Vernochet, C.; Vannier, R.-N.; Huvé, M.; Pirovano, C.; Nowogrocki, G.; Mairesse, G.; Van Tendeloo, G. |
Title |
Chemical, structural and electrical characterizations in the BIZNVOX family |
Type |
A1 Journal article |
Year |
2000 |
Publication |
Journal of materials chemistry |
Abbreviated Journal ![sorted by Abbreviated Journal field, ascending order (up)](img/sort_asc.gif) |
J Mater Chem |
Volume |
10 |
Issue |
12 |
Pages |
2811-2817 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Cambridge |
Editor |
|
Language |
|
Wos |
000165487800037 |
Publication Date |
2002-07-26 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0959-9428;1364-5501; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
13 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: NA |
Call Number |
UA @ lucian @ c:irua:54757 |
Serial |
351 |
Permanent link to this record |