| |
Records |
Links |
|
Author |
Vassiliev, S.Y.; Laurinavichute, V.K.; Abakumov, A.M.; Govorov, V.A.; Bendovskii, E.B.; Turner, S.; Filatov, A.Y.; Tarasovskii, V.P.; Borzenko, A.G.; Alekseeva, A.M.; Antipov, E.V. |
|
| |
Title |
Microstructural aspects of the degradation behavior of SnO2-based anodes for aluminum electrolysis |
Type |
A1 Journal article |
| |
Year |
2010 |
Publication  |
Journal of the electrochemical society |
Abbreviated Journal |
J Electrochem Soc |
|
| |
Volume |
157 |
Issue |
5 |
Pages |
C178-C186 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
The performance of SnO2 ceramic anodes doped with copper and antimony oxides was examined in cryolite alumina melts under anodic polarization at different cryolite ratios, temperatures, times, and current densities. The corroded part consists of a narrow strong corrosion zone at the anode surface with damage of the intergrain contacts and a large increase in porosity, a wider moderate corrosion zone with a smaller porosity increase, and a Cu depletion zone, where the ceramic retains its initial microstructure and a slight porosity increase occurs due to the removal of the Cu-rich inclusions. Mechanical destruction of the anode was never observed in the 10100 h tests. A microstructural model of the ceramic was suggested, consisting of grains with an Sb-doped SnO2 grain core surrounded by an ~200 to 500 nm grain shell where SnO2 was simultaneously doped with Sb and Mn+ (M=Cu2+,Fe3+,Al3+). The grains were separated by a few nanometers thick Cu-enriched grain boundaries. Different secondary charge carrier (holes) concentrations and electric conductivities in the grain core and grain shell result in a higher current density at the intergrain regions that leads to their profound degradation, especially in the low temperature acidic melt. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
New York, N.Y. |
Editor |
|
|
| |
Language |
|
Wos |
000276555300037 |
Publication Date |
2010-04-12 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0013-4651; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
3.259 |
Times cited |
3 |
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 3.259; 2010 IF: 2.427 |
|
| |
Call Number |
UA @ lucian @ c:irua:82260 |
Serial |
2040 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
McCalla, E.; Prakash, A.S.; Berg, E.; Saubanere, M.; Abakumov, A.M.; Foix, D.; Klobes, B.; Sougrati, M.T.; Rousse, G.; Lepoivre, F.; Mariyappan, S.; Doublet, M.L.; Gonbeau, D.; Novak, P.; Van Tendeloo, G.; Hermann, R.P.; Tarascon, J.M.; |
|
| |
Title |
Reversible Li-intercalation through oxygen reactivity in Li-rich Li-Fe-Te oxide materials |
Type |
A1 Journal article |
| |
Year |
2015 |
Publication |
Journal of the electrochemical society |
Abbreviated Journal |
J Electrochem Soc |
|
| |
Volume |
162 |
Issue |
162 |
Pages |
A1341-A1351 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
Lithium-rich oxides are a promising class of positive electrode materials for next generation lithium-ion batteries, and oxygen plays a prominent role during electrochemical cycling either by forming peroxo-like species and/or by irreversibly forming oxygen gas during first charge. Here, we present Li-Fe-Te-O materials which show a tremendous amount of oxygen gas release. This oxygen release accounts for nearly all the capacity during the first charge and results in vacancies as seen by transmission electron microscopy. There is no oxidation of either metal during charge but significant changes in their environments. These changes are particularly extreme for tellurium. XRD and neutron powder diffraction both show limited Changes during cycling and no appreciable change in lattice parameters. A density functional theory study of this material is performed and demonstrates that the holes created on some of the oxygen atoms upon oxidation are partially stabilized through the formation of shorter O-O bonds, i.e. (O-2)(n-) species which on further delithiation show a spontaneous O-2 de-coordination from the cationic network and migration to the now empty lithium layer. The rate limiting step during charge is undoubtedly the diffusion of oxygen either out along the lithium layer or via columns of oxygen atoms. (C) 2015 The Electrochemical Society. All rights reserved. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
New York, N.Y. |
Editor |
|
|
| |
Language |
|
Wos |
000355643700030 |
Publication Date |
2015-04-29 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0013-4651;1945-7111; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
3.259 |
Times cited |
23 |
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 3.259; 2015 IF: 3.266 |
|
| |
Call Number |
c:irua:126445 |
Serial |
2903 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Zhang, F.; Vanmeensel, K.; Inokoshi, M.; Batuk, M.; Hadermann, J.; Van Meerbeek, B.; Naert, I.; Vleugels, J. |
|
| |
Title |
3Y-TZP ceramics with improved hydrothermal degradation resistance and fracture toughness |
Type |
A1 Journal article |
| |
Year |
2014 |
Publication |
Journal of the European Ceramic Society |
Abbreviated Journal |
J Eur Ceram Soc |
|
| |
Volume |
34 |
Issue |
10 |
Pages |
2453-2463 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
Different factors such as the way of incorporating the Y2O3 stabilizer, alumina addition and sintering temperature were assessed with the goal to improve the low temperature degradation (LTD) resistance of 3Y-TZP without compromising on the mechanical properties. The degradation of hydrothermally treated specimens was studied by X-ray diffraction, micro-Raman spectroscopy and scanning electron microscopy. Decreasing the sintering temperature decreased the LTD susceptibility of 3Y-TZPs but did not allow to obtain a LTD resistant 3Y-TZP with optimized mechanical properties. Alumina addition along with the use of Y2O3 stabilizer coated starting powder allowed to combine both an excellent toughness and LTD resistance, as compared to alumina-free and stabilizer co-precipitated powder based equivalents. Transmission electron microscopy revealed that the improved LTD resistance could be attributed to the segregation of Al3+ at the grain boundary and the heterogeneously distributed Y3+ stabilizer. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
Barking |
Editor |
|
|
| |
Language |
|
Wos |
000336352500033 |
Publication Date |
2014-03-07 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0955-2219; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
3.411 |
Times cited |
48 |
Open Access |
|
|
| |
Notes |
Fwo G.0431.10n |
Approved |
Most recent IF: 3.411; 2014 IF: 2.947 |
|
| |
Call Number |
UA @ lucian @ c:irua:117065 c:irua:117065 |
Serial |
11 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Zhang, F.; Vanmeensel, K.; Inokoshi, M.; Batuk, M.; Hadermann, J.; Van Meerbeek, B.; Naert, I.; Vleugels, J. |
|
| |
Title |
Critical influence of alumina content on the low temperature degradation of 2-3 mol% yttria-stabilized TZP for dental restorations |
Type |
A1 Journal article |
| |
Year |
2015 |
Publication |
Journal of the European Ceramic Society |
Abbreviated Journal |
J Eur Ceram Soc |
|
| |
Volume |
35 |
Issue |
35 |
Pages |
741-750 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
The influence of 0.25, 2 and 5 wt.% alumina addition on the mechanical properties and low temperature degradation (LTD) of 3, 2.5 and 2 mol% yttria-stabilized TZP ceramics was investigated. The amount of alumina addition was observed to have a crucial impact on the degradation of Y-TZP ceramics. Independent on the yttria stabilizer content, 0.25 wt.% alumina had a higher degradation retarding effect to Y-TZP ceramics than 2 and 5 wt.% of alumina addition, which had a comparable effect. The apparent activation energy for the degradation process was increased by adding alumina, but it was the same for 0.255 wt.% alumina doped 3Y-TZP ceramics. For Y-TZPs containing a small amount of alumina addition, only the segregated Al3+ at the grain boundaries of the zirconia grains was effective to retard the degradation of Y-TZPs. The secondary phase Al2O3 grains increased the degradation kinetics, which might be attributed to the residual stresses. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
Barking |
Editor |
|
|
| |
Language |
|
Wos |
000345201700032 |
Publication Date |
2014-09-27 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0955-2219; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
3.411 |
Times cited |
37 |
Open Access |
|
|
| |
Notes |
Fwo G043110n |
Approved |
Most recent IF: 3.411; 2015 IF: 2.947 |
|
| |
Call Number |
c:irua:121328 |
Serial |
544 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Van Tendeloo, G.; Krekels, T. |
|
| |
Title |
HREM of ceramic high Tc superconductors |
Type |
A1 Journal article |
| |
Year |
1996 |
Publication |
Journal of the European Ceramic Society |
Abbreviated Journal |
J Eur Ceram Soc |
|
| |
Volume |
16 |
Issue |
|
Pages |
367-378 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
|
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
Barking |
Editor |
|
|
| |
Language |
|
Wos |
A1996UC80200005 |
Publication Date |
2002-07-25 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0955-2219; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
2.947 |
Times cited |
1 |
Open Access |
|
|
| |
Notes |
|
Approved |
no |
|
| |
Call Number |
UA @ lucian @ c:irua:16861 |
Serial |
1507 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Xu, T.; Wang, P.; Fang, P.; Kan, Y.; Chen, L.; Vleugels, J.; Van der Biest, O.; van Landuyt, J. |
|
| |
Title |
Phase assembly and microstructure of CeO2-doped ZrO2 ceramics prepared by spark plasma sintering |
Type |
A1 Journal article |
| |
Year |
2005 |
Publication |
Journal of the European Ceramic Society |
Abbreviated Journal |
J Eur Ceram Soc |
|
| |
Volume |
25 |
Issue |
15 |
Pages |
3437-3442 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
CeO2-doped ZrO2, (8 mol%) starting powder was sintered by means of spark plasma sintering (SPS) at 1300 degrees C without holding time. The stability of the tetragonal ZrO2 phase in the Ce-ZrO2 ceramic sintered under strongly reducing conditions was investigated. The SPS sample consisted of monoclinic and tetragonal ZrO2 phase, with a volume ratio of two to one, as well as a trace amount of a Zr-Ce-O cubic solid solution phase. In contrast, the same powder sintered by hot-pressing in nitrogen at 1300 and 1500 degrees C for 1h showed no tetragonal ZrO2. Microstructural observation of the SPS ceramic by SEM and TEM revealed grains with and without twins. The reason for the appearance of the tetragonal phase in the SPS sample sintered under strongly reducing conditions is discussed. (c) 2004 Elsevier Ltd. All rights reserved. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
Barking |
Editor |
|
|
| |
Language |
|
Wos |
000232172100006 |
Publication Date |
2004-12-16 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0955-2219; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
3.411 |
Times cited |
13 |
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 3.411; 2005 IF: 1.567 |
|
| |
Call Number |
UA @ lucian @ c:irua:104065 |
Serial |
2576 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Papageorgiou, D.G.; Filippousi, M.; Pavlidou, E.; Chrissafis, K.; Van Tendeloo, G.; Bikiaris, D. |
|
| |
Title |
Effect of clay modification on structureproperty relationships and thermal degradation kinetics of \beta-polypropylene/clay composite materials |
Type |
A1 Journal article |
| |
Year |
2015 |
Publication |
Journal of thermal analysis and calorimetry |
Abbreviated Journal |
J Therm Anal Calorim |
|
| |
Volume |
122 |
Issue |
122 |
Pages |
393-406 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
The influence of neat and organically modified montmorillonite on the structureproperty relationships of a β-nucleated polypropylene matrix has been thoroughly investigated. High-angle annular dark field scanning transmission electron microscopy revealed that the organic modification of clay facilitated the dispersion of the clay, while X-ray diffractograms showed the α-nucleating effect of the clays on the β-nucleated matrix. The results from tensile tests showed that the organic modification of MMT affected profoundly only the tensile strength at yield and at break. The effect of the organic modification of the clay on the thermal stability of the composites was finally evaluated by thermogravimetric analysis, where the samples filled with oMMT decomposed faster than the ones filled with neat MMT, due to the decomposition of the organic salts that were initially used for the modification of MMT. A kinetics study of the thermal degradation of the composites was also performed, in order to export additional conclusions on the activation energy of the samples. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
S.l. |
Editor |
|
|
| |
Language |
|
Wos |
000361431200042 |
Publication Date |
2015-04-29 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1388-6150;1588-2926; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
1.953 |
Times cited |
7 |
Open Access |
|
|
| |
Notes |
262348 Esmi |
Approved |
Most recent IF: 1.953; 2015 IF: 2.042 |
|
| |
Call Number |
c:irua:127492 |
Serial |
805 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Lubyshev, D.; Fastenau, J.M.; Fang, X.-M.; Wu, Y.; Doss, C.; Snyder, A.; Liu, W.K.; Lamb, M.S.M.; Bals, S.; Song, C. |
|
| |
Title |
Comparison of As- and P-based metamorphic buffers for high performance InP heterojunction bipolar transistor and high electron mobility transistor applications |
Type |
A1 Journal article |
| |
Year |
2004 |
Publication |
Journal of vacuum science & technology. B. Microelectronics and nanometer structures. Processing, measurement and phenomena |
Abbreviated Journal |
|
|
| |
Volume |
22 |
Issue |
3 |
Pages |
1565-1569 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
Metamorphic buffers (M-buffers) consisting of graded InAlAs or bulk InP were employed for the production of InP-based epiwafers on GaAs substrates by molecular-beam epitaxy. The graded InAlAs is the standard for production metamorphic high electron mobility transistors (M-HEMTs), while the bulk InP offers superior thermal properties for higher current density circuits. The surface morphology and crystal structure of the two M-buffers showed different relaxation mechanisms. The graded InAlAs gave a cross-hatched pattern with nearly full relaxation and very effective dislocation filtering, while the bulk InP had a uniform isotropic surface with dislocations propagating further up towards the active layers. Both types of M-buffers had atomic force microscopy root-mean-square roughness values around 2030 Å. The Hall transport properties of high electron mobility transistors (HEMTs) grown on the InAlAs M-buffer, and a baseline HEMT grown lattice matched on InP, both had room-temperature mobilities >10 000 cm2/V s, while the M-HEMT on the InP M-buffer showed a decrease to 9000 cm2/V s. Similarly, the dc parameters of a double heterojunction bipolar transistor (DHBT) grown on the InAlAs M-buffer were much closer to the baseline heterojunction bipolar transistor than a DHBT grown on the InP M-buffer. A high breakdown voltage of 11.3 V was achieved on an M-DHBT with the InAlAs M-buffer. We speculate that the degradation in device characteristics on the InP M-buffer was related to the incomplete dislocation filtering. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
Woodbury, N.Y. |
Editor |
|
|
| |
Language |
|
Wos |
000222481400141 |
Publication Date |
2004-07-08 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0734-211X; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
|
Times cited |
25 |
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ lucian @ c:irua:87596 |
Serial |
427 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Dubourdieu, C.; Rauwel, E.; Roussel, H.; Ducroquet, F.; Hollaender, B.; Rossell, M.; Van Tendeloo, G.; Lhostis, S.; Rushworth, S. |
|
| |
Title |
Addition of yttrium into HfO2 films: microstructure and electrical properties |
Type |
A1 Journal article |
| |
Year |
2009 |
Publication |
Journal of vacuum science and technology: A: vacuum surfaces and films |
Abbreviated Journal |
J Vac Sci Technol A |
|
| |
Volume |
27 |
Issue |
3 |
Pages |
503-514 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
The cubic phase of HfO2 was stabilized by addition of yttrium in thin films grown on Si/SiO2 by metal-organic chemical vapor deposition. The cubic phase was obtained for contents of 6.5 at. % Y or higher at a temperature as low as 470 °C. The complete compositional range (from 1.5 to 99.5 at. % Y) was investigated. The crystalline structure of HfO2 was determined from x-ray diffraction, electron diffraction, and attenuated total-reflection infrared spectroscopy. For cubic films, the continuous increase in the lattice parameter indicates the formation of a solid-solution HfO2Y2O3. As shown by x-ray photoelectron spectroscopy, yttrium silicate is formed at the interface with silicon; the interfacial layer thickness increases with increasing yttrium content and increasing film thickness. The dependence of the intrinsic relative permittivity r as a function of Y content was determined. It exhibits a maximum of ~30 for ~8.8 at. % Y. The cubic phase is stable upon postdeposition high-temperature annealing at 900 °C under NH3. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
New York, N.Y. |
Editor |
|
|
| |
Language |
|
Wos |
000265739100016 |
Publication Date |
2009-05-02 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0734-2101; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
1.374 |
Times cited |
29 |
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 1.374; 2009 IF: 1.297 |
|
| |
Call Number |
UA @ lucian @ c:irua:77054 |
Serial |
58 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Mihailescu, I.N.; Gyorgy, E.; Marin, G.; Popescu, M.; Teodorescu, V.S.; van Landuyt, J.; Grivas, C.; Hatziapostolou, A. |
|
| |
Title |
Crystalline structure of very hard tungsten carbide thin films obtained by reactive pulsed laser deposition |
Type |
A1 Journal article |
| |
Year |
1999 |
Publication |
Journal of vacuum science and technology: A: vacuum surfaces and films |
Abbreviated Journal |
J Vac Sci Technol A |
|
| |
Volume |
17 |
Issue |
1 |
Pages |
249-255 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
|
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
New York, N.Y. |
Editor |
|
|
| |
Language |
|
Wos |
000078136300038 |
Publication Date |
2002-07-27 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0734-2101; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
1.374 |
Times cited |
8 |
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 1.374; 1999 IF: 1.742 |
|
| |
Call Number |
UA @ lucian @ c:irua:29689 |
Serial |
581 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Cremers, V.; Rampelberg, G.; Baert, K.; Abrahami, S.; Claes, N.; de Oliveira, T.M.; Terryn, H.; Bals, S.; Dendooven, J.; Detavernier, C. |
|
| |
Title |
Corrosion protection of Cu by atomic layer deposition |
Type |
A1 Journal article |
| |
Year |
2019 |
Publication |
Journal of vacuum science and technology: A: vacuum surfaces and films |
Abbreviated Journal |
J Vac Sci Technol A |
|
| |
Volume |
37 |
Issue |
37 |
Pages |
060902 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
Atomic layer deposition (ALD) is a vapor phase technique that is able to deposit uniform, conformal thin films with an excellent thickness control at the atomic scale. 18 nm thick Al2O3 and TiO2 coatings were deposited conformaly and pinhole-free onto micrometer-sized Cu powder, using trimethylaluminum and tetrakis(dimethylamido)titanium(IV), respectively, as a precursor and de-ionized water as a reactant. The capability of the ALD coating to protect the Cu powder against corrosion was investigated. Therefore, the stability of the coatings was studied in solutions with different pH in the range of 0–14, and in situ raman spectroscopy was used to detect the emergence of corrosion products of Cu as an indication that the protective coating starts to fail. Both ALD coatings provide good protection at standard pH values in the range of 5–7. In general, the TiO2 coating shows a better barrier protection against corrosion than the Al2O3 coating. However, for the most extreme pH conditions, pH 0 and pH 14, the TiO2 coating starts also to degrade. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000517925800003 |
Publication Date |
2019-09-19 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0734-2101 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
1.374 |
Times cited |
7 |
Open Access |
OpenAccess |
|
| |
Notes |
The authors acknowledge financial support from the Strategic Initiative Materials in Flanders (SIM, SBO-FUNC project) and the Special Research Fund BOF of Ghent University (No. GOA 01G01513). J.D. acknowledges the Research Foundation Flanders (FWO-Vlaanderen) for a postdoctoral fellowship. |
Approved |
Most recent IF: 1.374 |
|
| |
Call Number |
EMAT @ emat @c:irua:162640 |
Serial |
5361 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Wu, M.F.; Zhou, S.; Yao, S.; Zhao, Q.; Vantomme, A.; van Daele, B.; Piscopiello, E.; Van Tendeloo, G.; Tong, Y.Z.; Yang, Z.J.; Yu, T.J.; Zhang, G.Y. |
|
| |
Title |
High precision determination of the elastic strain of InGaN/GaN multiple quantum wells |
Type |
A1 Journal article |
| |
Year |
2004 |
Publication |
Journal of vacuum science and technology: B: microelectronics and nanometer structures |
Abbreviated Journal |
|
|
| |
Volume |
22 |
Issue |
3 |
Pages |
920-924 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
|
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000222481400010 |
Publication Date |
2004-07-08 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0734-211X; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
|
Times cited |
15 |
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ lucian @ c:irua:54863 |
Serial |
1437 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Calogiuri, T.; Hagens, M.; Van Groenigen, J.W.; Corbett, T.; Hartmann, J.; Hendriksen, R.; Janssens, I.; Janssens, I.A.; Ledesma Dominguez, G.; Loescher, G.; Mortier, S.; Neubeck, A.; Niron, H.; Poetra, R.P.; Rieder, L.; Struyf, E.; Van Tendeloo, M.; De Schepper, T.; Verdonck, T.; Vlaeminck, S.E.; Vicca, S.; Vidal, A. |
|
| |
Title |
Design and construction of an experimental setup to enhance mineral weathering through the activity of soil organisms |
Type |
A1 Journal article |
| |
Year |
2023 |
Publication |
Journal of visualized experiments |
Abbreviated Journal |
|
|
| |
Volume |
|
Issue |
201 |
Pages |
e65563-30 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Internet Data Lab (IDLab); Applied mathematics; Sustainable Energy, Air and Water Technology (DuEL); Plant and Ecosystems (PLECO) – Ecology in a time of change |
|
| |
Abstract |
Enhanced weathering (EW) is an emerging carbon dioxide (CO2) removal technology that can contribute to climate change mitigation. This technology relies on accelerating the natural process of mineral weathering in soils by manipulating the abiotic variables that govern this process, in particular mineral grain size and exposure to acids dissolved in water. EW mainly aims at reducing atmospheric CO2 concentrations by enhancing inorganic carbon sequestration. Until now, knowledge of EW has been mainly gained through experiments that focused on the abiotic variables known for stimulating mineral weathering, thereby neglecting the potential influence of biotic components. While bacteria, fungi, and earthworms are known to increase mineral weathering rates, the use of soil organisms in the context of EW remains underexplored. This protocol describes the design and construction of an experimental setup developed to enhance mineral weathering rates through soil organisms while concurrently controlling abiotic conditions. The setup is designed to maximize weathering rates while maintaining soil organisms' activity. It consists of a large number of columns filled with rock powder and organic material, located in a climate chamber and with water applied via a downflow irrigation system. Columns are placed above a fridge containing jerrycans to collect the leachate. Representative results demonstrate that this setup is suitable to ensure the activity of soil organisms and quantify their effect on inorganic carbon sequestration. Challenges remain in minimizing leachate losses, ensuring homogeneous ventilation through the climate chamber, and avoiding flooding of the columns. With this setup, an innovative and promising approach is proposed to enhance mineral weathering rates through the activity of soil biota and disentangle the effect of biotic and abiotic factors as drivers of EW. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
001127854400015 |
Publication Date |
2023-11-12 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1940-087x |
ISBN |
|
Additional Links |
UA library record; WoS full record |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
no |
|
| |
Call Number |
UA @ admin @ c:irua:200770 |
Serial |
9019 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Gorle, C.; Garcia Sánchez, C.; Iaccarino, G. |
|
| |
Title |
Quantifying inflow and RANS turbulence model form uncertainties for wind engineering flows |
Type |
A1 Journal article |
| |
Year |
2015 |
Publication |
Journal of wind engineering and industrial aerodynamics
T2 – 6th International Symposium on Computational Wind Engineering (CWE), JUN 08-12, 2014, Hamburg, GERMANY |
Abbreviated Journal |
J Wind Eng Ind Aerod |
|
| |
Volume |
144 |
Issue |
144 |
Pages |
202-212 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
Reynolds-averaged Navier-Stokes (RANS) simulations are often used in the wind engineering practice for the analysis of turbulent bluff body flows. An approach that allows identifying the uncertainty related to the use of reduced-order turbulence models in RANS simulations would significantly increase the confidence in the use of simulation results as a basis for design decisions. In the present study we apply a strategy that enables quantifying these uncertainties by introducing perturbations in the Reynolds stress tensor to simulations of the flow in downtown Oklahoma City. The method is combined with a framework to quantify uncertainties in the inflow wind direction and intensity, and the final result of the UQ approach is compared to field measurement data for the velocity at 13 locations in the downtown area. (C) 2015 Elsevier Ltd. All rights reserved. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
Elsevier science bv |
Place of Publication |
Amsterdam |
Editor |
|
|
| |
Language |
|
Wos |
000360874900023 |
Publication Date |
2015-08-18 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0167-6105 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
2.049 |
Times cited |
22 |
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 2.049; 2015 IF: 1.414 |
|
| |
Call Number |
UA @ lucian @ c:irua:127843 |
Serial |
4230 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Longo, R.; Ferrarotti, M.; Garcia Sánchez, C.; Derudi, M.; Parente, A. |
|
| |
Title |
Advanced turbulence models and boundary conditions for flows around different configurations of ground-mounted buildings |
Type |
A1 Journal article |
| |
Year |
2017 |
Publication |
Journal of wind engineering and industrial aerodynamics |
Abbreviated Journal |
J Wind Eng Ind Aerod |
|
| |
Volume |
167 |
Issue |
|
Pages |
160-182 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
When dealing with Atmospheric Boundary Layer (ABL) simulations, commercial computational fluid dynamics (CFD) acquires a strategic resonance. Thanks to its good compromise between accuracy of results and calculation time, RANS still represents a valid alternative to more resource-demanding methods. However, focusing on the models' performances in urban studies, LES generally outmatches RANS results, even if the former is at least one order of magnitude more expensive. Consequently, the present work aims to propose a variety of approaches meant to solve some of the major problems linked to RANS simulations and to further improve its accuracy in typical urban contexts. All of these models are capable of switching from an undisturbed flux formulation to a disturbed one through a local deviation or a marker function. For undisturbed flows, a comprehensive approach is adopted, solving the issue of the erroneous stream-wise gradients affecting the turbulent profiles. Around obstacles, Non-Linear Eddy-Viscosity closures are adopted, due to their prominent capability in capturing the anisotropy of turbulence. The purpose of this work is then to propose a new Building Influence Area concept and to offer more affordable alternatives to LES simulations without sacrificing a good grade of accuracy. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
|
| |
Language |
|
Wos |
000405766600013 |
Publication Date |
2017-05-02 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0167-6105 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
2.049 |
Times cited |
9 |
Open Access |
Not_Open_Access |
|
| |
Notes |
; ; |
Approved |
Most recent IF: 2.049 |
|
| |
Call Number |
UA @ lucian @ c:irua:145191 |
Serial |
4713 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Cheng, J.P.; Zhang, X.B.; Ye, Y.; Tao, X.Y.; Liu, F.; Li, Y.; Van Tendeloo, G. |
|
| |
Title |
Natural mineral-marine manganese nodule as a novel catalyst for the synthesis of carbon nanotubes |
Type |
A1 Journal article |
| |
Year |
2006 |
Publication |
Journal of Wuhan University of Technology: materials science edition |
Abbreviated Journal |
|
|
| |
Volume |
21 |
Issue |
1 |
Pages |
29-31 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
|
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
|
Publication Date |
0000-00-00 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
|
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ lucian @ c:irua:57740 |
Serial |
2286 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
van der Jeught, S.; Muyshondt, P.G.G.; Lobato, I. |
|
| |
Title |
Optimized loss function in deep learning profilometry for improved prediction performance |
Type |
A1 Journal article |
| |
Year |
2021 |
Publication |
JPhys Photonics |
Abbreviated Journal |
|
|
| |
Volume |
3 |
Issue |
2 |
Pages |
024014 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
Single-shot structured light profilometry (SLP) aims at reconstructing the 3D height map of an object from a single deformed fringe pattern and has long been the ultimate goal in fringe projection profilometry. Recently, deep learning was introduced into SLP setups to replace the task-specific algorithm of fringe demodulation with a dedicated neural network. Research on deep learning-based profilometry has made considerable progress in a short amount of time due to the rapid development of general neural network strategies and to the transferrable nature of deep learning techniques to a wide array of application fields. The selection of the employed loss function has received very little to no attention in the recently reported deep learning-based SLP setups. In this paper, we demonstrate the significant impact of loss function selection on height map prediction accuracy, we evaluate the performance of a range of commonly used loss functions and we propose a new mixed gradient loss function that yields a higher 3D surface reconstruction accuracy than any previously used loss functions. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000641030000001 |
Publication Date |
2021-03-18 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
2515-7647 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
OpenAccess |
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ admin @ c:irua:178171 |
Serial |
6797 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Van Aert, S. |
|
| |
Title |
Meer zien met onzichtbaar licht |
Type |
A2 Journal article |
| |
Year |
2007 |
Publication |
Karakter : tijdschrift van wetenschap |
Abbreviated Journal |
|
|
| |
Volume |
18 |
Issue |
|
Pages |
19-21 |
|
| |
Keywords |
A2 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
|
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
Leuven |
Editor |
|
|
| |
Language |
|
Wos |
|
Publication Date |
0000-00-00 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1379-0390 |
ISBN |
|
Additional Links |
UA library record |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ lucian @ c:irua:68658 |
Serial |
1982 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Bervoets, A.R.J.; Behets, G.J.; Schryvers, D.; Roels, F.; Yang, Z.; Verberckmoes, S.C.; Damment, S.J.P.; Dauwe, S.; Mubiana, V.K.; Blust, R.; de Broe, M.E.; d' Haese, P.C. |
|
| |
Title |
Hepatocellular transport and gastrointestinal absorption of lanthanum in chronic renal failure |
Type |
A1 Journal article |
| |
Year |
2009 |
Publication |
Kidney international |
Abbreviated Journal |
Kidney Int |
|
| |
Volume |
75 |
Issue |
|
Pages |
389-398 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT); Pathophysiology |
|
| |
Abstract |
Lanthanum carbonate is a new phosphate binder that is poorly absorbed from the gastrointestinal tract and eliminated largely by the liver. After oral treatment, we and others had noticed 23 fold higher lanthanum levels in the livers of rats with chronic renal failure compared to rats with normal renal function. Here we studied the kinetics and tissue distribution, absorption, and subcellular localization of lanthanum in the liver using transmission electron microscopy, electron energy loss spectrometry, and X-ray fluoresence. We found that in the liver lanthanum was located in lysosomes and in the biliary canal but not in any other cellular organelles. This suggests that lanthanum is transported and eliminated by the liver via a transcellular, endosomal-lysosomal-biliary canicular transport route. Feeding rats with chronic renal failure orally with lanthanum resulted in a doubling of the liver levels compared to rats with normal renal function, but the serum levels were similar in both animal groups. These levels plateaued after 6 weeks at a concentration below 3 g/g in both groups. When lanthanum was administered intravenously, thereby bypassing the gastrointestinal tract-portal vein pathway, no difference in liver levels was found between rats with and without renal failure. This suggests that there is an increased gastrointestinal permeability or absorption of oral lanthanum in uremia. Lanthanum levels in the brain and heart fluctuated near its detection limit with long-term treatment (20 weeks) having no effect on organ weight, liver enzyme activities, or liver histology. We suggest that the kinetics of lanthanum in the liver are consistent with a transcellular transport pathway, with higher levels in the liver of uremic rats due to higher intestinal absorption. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
New York, N.Y. |
Editor |
|
|
| |
Language |
|
Wos |
000263145800009 |
Publication Date |
2008-12-03 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0085-2538;1523-1755; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
8.395 |
Times cited |
29 |
Open Access |
|
|
| |
Notes |
Fwo; Iwt |
Approved |
Most recent IF: 8.395; 2009 IF: 6.193 |
|
| |
Call Number |
UA @ lucian @ c:irua:72290 |
Serial |
1417 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Vervaet, B.A.; Nast, C.C.; Jayasumana, C.; Schreurs, G.; Roels, F.; Herath, C.; Kojc, N.; Samaee, V.; Rodrigo, S.; Gowrishankar, S.; Mousson, C.; Dassanayake, R.; Orantes, C.M.; Vuiblet, V.; Rigothier, C.; d' Haese, P.C.; de Broe, M.E. |
|
| |
Title |
Chronic interstitial nephritis in agricultural communities is a toxin induced proximal tubular nephropathy |
Type |
A1 Journal article |
| |
Year |
2019 |
Publication |
Kidney international |
Abbreviated Journal |
Kidney Int |
|
| |
Volume |
97 |
Issue |
97 |
Pages |
350-369 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT); Laboratory Experimental Medicine and Pediatrics (LEMP); Pathophysiology |
|
| |
Abstract |
Almost 30 years after the detection of chronic interstitial nephritis in agricultural communities (CINAC) its etiology remains unknown. To help define this we examined 34 renal biopsies from Sri Lanka, El Salvador, India and France of patients with chronic kidney disease 2-3 and diagnosed with CINAC by light and electron microscopy. In addition to known histopathology, we identified a unique constellation of proximal tubular cell findings including large dysmorphic lysosomes with a light-medium electron-dense matrix containing dispersed dark electron-dense non-membrane bound “aggregates”. These aggregates associated with varying degrees of cellular/tubular atrophy, apparent cell fragment shedding and no-weak proximal tubular cell proliferative capacity. Identical lysosomal lesions, identifiable by electron microscopy, were observed in 9% of renal transplant implantation biopsies, but were more prevalent in six month (50%) and 12 month (67%) protocol biopsies and in indication biopsies (76%) of calcineurin inhibitor treated transplant patients. The phenotype was also found associated with nephrotoxic drugs (lomustine, clomiphene, lithium, cocaine) and in some patients with light chain tubulopathy, all conditions that can be directly or indirectly linked to calcineurin pathway inhibition or modulation. One hundred biopsies of normal kidneys, drug/toxin induced nephropathies, and overt proteinuric patients of different etiologies to some extent could demonstrate the light microscopic proximal tubular cell changes, but rarely the electron microscopic lysosomal features. Rats treated with the calcineurin inhibitor cyclosporine for four weeks developed similar proximal tubular cell lysosomal alterations, which were absent in a dehydration group. Overall, the finding of an identical proximal tubular cell (lysosomal) lesion in CINAC and calcineurin inhibitor nephrotoxicity in different geographic regions suggests a common paradigm where CINAC patients undergo a tubulotoxic mechanism similar to calcineurin inhibitor nephrotoxicity. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000508449300020 |
Publication Date |
2019-11-23 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0085-2538; 1523-1755 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
8.395 |
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 8.395 |
|
| |
Call Number |
UA @ admin @ c:irua:164305c:irua:166544 |
Serial |
5384 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Fredrickx, P.; Schryvers, D. |
|
| |
Title |
La microscopie électronique à transmission (MET) et son utilisation dans l'étude d'inclusions nano-cristallines dans le verre |
Type |
A3 Journal article |
| |
Year |
2002 |
Publication |
L'archéométrie au service des monuments et des oeuvres d'art |
Abbreviated Journal |
|
|
| |
Volume |
10 |
Issue |
|
Pages |
131-136 |
|
| |
Keywords |
A3 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
|
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
|
Publication Date |
0000-00-00 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
|
ISBN |
|
Additional Links |
UA library record |
|
| |
Impact Factor |
|
Times cited |
|
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: NA |
|
| |
Call Number |
UA @ lucian @ c:irua:48776 |
Serial |
2036 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Buschmann, V.; Van Tendeloo, G. |
|
| |
Title |
Structural characterization of colloidal Ag2Se nanocrystals |
Type |
A1 Journal article |
| |
Year |
1998 |
Publication |
Langmuir |
Abbreviated Journal |
Langmuir |
|
| |
Volume |
14 |
Issue |
|
Pages |
1528-1531 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
|
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
|
Editor |
|
|
| |
Language |
|
Wos |
000072914700007 |
Publication Date |
2002-07-26 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0743-7463;1520-5827; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
3.833 |
Times cited |
15 |
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 3.833; 1998 IF: 2.813 |
|
| |
Call Number |
UA @ lucian @ c:irua:25659 |
Serial |
3218 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Bertels, E.; Bruyninckx, K.; Kurttepeli; Smet, M.; Bals, S.; Goderis, B. |
|
| |
Title |
Highly Efficient Hyperbranched CNT Surfactants: Influence of Molar Mass and Functionalization |
Type |
A1 Journal article |
| |
Year |
2014 |
Publication |
Langmuir: the ACS journal of surfaces and colloids |
Abbreviated Journal |
Langmuir |
|
| |
Volume |
30 |
Issue |
41 |
Pages |
12200-12209 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
End-group-functionalized hyperbranched polymers were synthesized to act as a carbon nanotube (CNT) surfactant in aqueous solutions. Variation of the percentage of triphenylmethyl (trityl) functionalization and of the molar mass of the hyperbranched polyglycerol (PG) core resulted in the highest measured surfactant efficiency for a 5000 g/mol PG with 5.6% of the available hydroxyl end-groups replaced by trityl functions, as shown by UV-vis measurements. Semiempirical model calculations suggest an even higher efficiency for PG5000 with 2.5% functionalization and maximal molecule specific efficiency in general at low degrees of functionalization. Addition of trityl groups increases the surfactant-nanotube interactions in comparison to unfunctionalized PG because of pi-pi stacking interactions. However, at higher functionalization degrees mutual interactions between trityl groups come into play, decreasing the surfactant efficiency, while lack of water solubility becomes an issue at very high functionalization degrees. Low molar mass surfactants are less efficient compared to higher molar mass species most likely because the higher bulkiness of the latter allows for a better CNT separation and stabilization. The most efficient surfactant studied allowed dispersing 2.85 mg of CNT in 20 mL with as little as 1 mg of surfactant. These dispersions, remaining stable for at least 2 months, were mainly composed of individual CNTs as revealed by electron microscopy. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
Washington, D.C. |
Editor |
|
|
| |
Language |
|
Wos |
000343638800013 |
Publication Date |
2014-09-23 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0743-7463;1520-5827; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
3.833 |
Times cited |
15 |
Open Access |
OpenAccess |
|
| |
Notes |
The authors gratefully acknowledge the SIM NanoForce programme for their financial support and thank the group of Prof. Thierry Verbiest, especially Maarten Bloemen, for the use of their UV−vis equipment. Bart Goderis and Mario Smet thank KU Leuven for financial support through a GOA project. Mert Kurttepeli and Sara Bals acknowledge funding from the European Research Council under the 7th Framework Program (FP7), ERC Starting Grant No. 335078 COLOURATOMS.; ECAS_Sara; (ROMEO:white; preprint:; postprint:restricted 12 months embargo; pdfversion:cannot); |
Approved |
Most recent IF: 3.833; 2014 IF: 4.457 |
|
| |
Call Number |
UA @ lucian @ c:irua:121140 |
Serial |
1471 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Vernimmen, J.; Guidotti, M.; Silvestre-Albero, J.; Jardim, E.O.; Mertens, M.; Lebedev, O.I.; Van Tendeloo, G.; Psaro, R.; Rodríguez-Reinoso, F.; Meynen, V.; Cool, P. |
|
| |
Title |
Immersion calorimetry as a tool to evaluate the catalytic performance of titanosilicate materials in the epoxidation of cyclohexene |
Type |
A1 Journal article |
| |
Year |
2011 |
Publication |
Langmuir: the ACS journal of surfaces and colloids |
Abbreviated Journal |
Langmuir |
|
| |
Volume |
27 |
Issue |
7 |
Pages |
3618-3625 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT); Laboratory of adsorption and catalysis (LADCA) |
|
| |
Abstract |
Different types of titanosilicates are synthesized, structurally characterized, and subsequently catalytically tested in the liquid-phase epoxidation of cyclohexene. The performance of three types of combined zeolitic/mesoporous materials is compared with that of widely studied Ti-grafted-MCM-41 molecular sieve and the TS-1 microporous titanosilicate. The catalytic test results are correlated with the structural characteristics of the different catalysts. Moreover, for the first time, immersion calorimetry with the same substrate molecule as in the catalytic test reaction is applied as an extra means to interpret the catalytic results. A good correlation between catalytic performance and immersion calorimetry results is found. This work points out that the combination of catalytic testing and immersion calorimetry can lead to important insights into the influence of the materials structural characteristics on catalysis. Moreover, the potential of using immersion calorimetry as a screening tool for catalysts in epoxidation reactions is shown. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
Washington, D.C. |
Editor |
|
|
| |
Language |
|
Wos |
000288970900054 |
Publication Date |
2011-02-23 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0743-7463;1520-5827; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
3.833 |
Times cited |
19 |
Open Access |
|
|
| |
Notes |
|
Approved |
Most recent IF: 3.833; 2011 IF: 4.186 |
|
| |
Call Number |
UA @ lucian @ c:irua:88366 |
Serial |
1557 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Barreca, D.; Carraro, G.; Gasparotto, A.; Maccato, C.; Lebedev, O.I.; Parfenova, A.; Turner, S.; Tondello, E.; Van Tendeloo, G. |
|
| |
Title |
Tailored vapor-phase growth of CuxO-TiO2(x=1,2) nanomaterials decorated with Au particles |
Type |
A1 Journal article |
| |
Year |
2011 |
Publication |
Langmuir: the ACS journal of surfaces and colloids |
Abbreviated Journal |
Langmuir |
|
| |
Volume |
27 |
Issue |
10 |
Pages |
6409-6417 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
We report on the fabrication of CuxOTiO2 (x = 1, 2) nanomaterials by an unprecedented vapor-phase approach. The adopted strategy involves the growth of porous CuxO matrices by means of chemical vapor deposition (CVD), followed by the controlled dispersion of TiO2 nanoparticles. The syntheses are performed on Si(100) substrates at temperatures of 400550 °C under wet oxygen atmospheres, adopting Cu(hfa)2·TMEDA (hfa =1,1,1,5,5,5-hexafluoro-2,4-pentanedionate; TMEDA = N,N,N′,N′-tetramethylethylenediamine) and Ti(O-iPr)2(dpm)2 (O-iPr = isopropoxy; dpm = 2,2,6,6-tetramethyl-3,5-heptanedionate) as copper and titanium precursors, respectively. Subsequently, finely dispersed gold nanoparticles are introduced in the as-prepared systems via radio frequency (RF)-sputtering under mild conditions. The synthesis process results in the formation of systems with chemical composition and nano-organization strongly dependent on the nature of the initial CuxO matrix and on the deposited TiO2 amount. The decoration with low-size gold clusters paves the way to the engineering of hierarchically organized nanomaterials. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
Washington, D.C. |
Editor |
|
|
| |
Language |
|
Wos |
000290292900082 |
Publication Date |
2011-04-25 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0743-7463;1520-5827; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
3.833 |
Times cited |
36 |
Open Access |
|
|
| |
Notes |
Fwo |
Approved |
Most recent IF: 3.833; 2011 IF: 4.186 |
|
| |
Call Number |
UA @ lucian @ c:irua:88940 |
Serial |
3467 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Cui, J.; Faria, M.; Bjornmalm, M.; Ju, Y.; Suma, T.; Gunawan, S.T.; Richardson, J.J.; Heidar, H.; Bals, S.; Crampin, E.J.; Caruso, F. |
|
| |
Title |
A framework to account for sedimentation and diffusion in particle-cell interactions |
Type |
A1 Journal article |
| |
Year |
2016 |
Publication |
Langmuir: the ACS journal of surfaces and colloids |
Abbreviated Journal |
Langmuir |
|
| |
Volume |
32 |
Issue |
32 |
Pages |
12394-12402 |
|
| |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
In vitro experiments provide a solid basis for understanding the interactions between particles and biological systems. An important confounding variable for these studies is the difference between the amount of particles administered and that which reaches the surface of cells. Here, we engineer a hydrogel-based nanoparticle system and combine in situ characterization techniques, 3D-printed cell cultures, and computational modeling to evaluate and study particle cell interactions of advanced particle systems. The framework presented demonstrates how sedimentation and diffusion can explain differences in particle cell association, and provides a means to account for these effects. Finally, using in silico modeling, we predict the proportion of particles that reaches the cell surface using common experimental conditions for a wide range of inorganic and organic micro- and nanoparticles. This work can assist in the understanding and control of sedimentation and diffusion when investigating cellular interactions of engineered particles. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
Washington, D.C. |
Editor |
|
|
| |
Language |
|
Wos |
000389117600017 |
Publication Date |
2016-07-06 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
0743-7463 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
3.833 |
Times cited |
40 |
Open Access |
Not_Open_Access |
|
| |
Notes |
; This work was supported by the Australian Research Council (ARC) under the Australian Laureate Fellowship scheme (F.C., FL120100030), the Australian Government through an Australian Postgraduate Award (M.B.), and the ARC Centre of Excellence in Convergent Bio-Nano Science and Technology (Project Number CE140100036). This work was performed in part at the Materials Characterization and Fabrication Platform (MCFP) at the University of Melbourne and the Victorian Node of the Australian National Fabrication Facility (ANFF). ; |
Approved |
Most recent IF: 3.833 |
|
| |
Call Number |
UA @ lucian @ c:irua:139210 |
Serial |
4438 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Conings, B.; Drijkoningen, J.; Gauquelin, N.; Babayigit, A.; D'Haen, J.; D'Olieslaeger, L.; Ethirajan, A.; Verbeeck, J.; Manca, J.; Mosconi, E.; Angelis, F.D.; Boyen, H.G.; |
|
| |
Title |
Intrinsic thermal instability of methylammonium lead trihalide perovskite |
Type |
A1 Journal article |
| |
Year |
2015 |
Publication |
Laser physics review |
Abbreviated Journal |
Adv Energy Mater |
|
| |
Volume |
5 |
Issue |
5 |
Pages |
1500477 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
Organolead halide perovskites currently are the new front-runners as light absorbers in hybrid solar cells, as they combine efficiencies passing already 20% with deposition temperatures below 100 °C and cheap solution-based fabrication routes. Long-term stability remains a major obstacle for application on an industrial scale. Here, it is demonstrated that significant decomposition effects already occur during annealing of a methylammonium lead triiode perovskite at 85 °C even in inert atmosphere thus violating international standards. The observed behavior supports the view of currently used perovskite materials as soft matter systems with low formation energies, thus representing a major bottleneck for their application, especially in countries with high average temperatures. This result can trigger a broader search for new perovskite families with improved thermal stability. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
S.l. |
Editor |
|
|
| |
Language |
|
Wos |
000359374900005 |
Publication Date |
2015-06-03 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1614-6832; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
16.721 |
Times cited |
1691 |
Open Access |
|
|
| |
Notes |
FWO G004413N; GOA Solarpaint |
Approved |
Most recent IF: 16.721; 2015 IF: 16.146 |
|
| |
Call Number |
c:irua:127298UA @ admin @ c:irua:127298 |
Serial |
1719 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Guerrero, A.; Heidari, H.; Ripolles, T.S.; Kovalenko, A.; Pfannmöller, M.; Bals, S.; Kauffmann, L.-D.; Bisquert, J.; Garcia-Belmonte, G. |
|
| |
Title |
Shelf life degradation of bulk heterojunction solar cells : intrinsic evolution of charge transfer complex |
Type |
A1 Journal article |
| |
Year |
2015 |
Publication |
Laser physics review |
Abbreviated Journal |
Adv Energy Mater |
|
| |
Volume |
5 |
Issue |
5 |
Pages |
1401997 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
Achievement of long-term stability of organic photovoltaics is currently one of the major topics for this technology to reach maturity. Most of the techniques used to reveal degradation pathways are destructive and/or do not allow for real-time measurements in operating devices. Here, three different, nondestructive techniques able to provide real-time information, namely, film absorbance, capacitance-voltage (C-V), and impedance spectroscopy (IS), are combined over a period of 1 year using non-accelerated intrinsic degradation conditions. It is discerned between chemical modifications in the active layer, physical processes taking place in the bulk of the blend from those at the active layer/contact interfaces. In particular, it is observed that during the ageing experiment, the main source for device performance degradation is the formation of donor-acceptor charge-transfer complex (P3HT(center dot+)-PCBM center dot-) that acts as an exciton quencher. Generation of these radical species diminishes photocurrent and reduces open-circuit voltage by the creation of electronic defect states. Conclusions extracted from absorption, C-V, and IS measurements will be further supported by a range of other techniques such as atomic force microscopy, X-ray diffraction, and dark-field imaging of scanning transmission electron microscopy on ultrathin cross-sections. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
S.l. |
Editor |
|
|
| |
Language |
|
Wos |
000352708600013 |
Publication Date |
2014-12-12 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1614-6832; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
16.721 |
Times cited |
30 |
Open Access |
OpenAccess |
|
| |
Notes |
287594 Sunflower; 335078 Colouratom; ECAS_Sara; (ROMEO:yellow; preprint:; postprint:restricted ; pdfversion:cannot); |
Approved |
Most recent IF: 16.721; 2015 IF: 16.146 |
|
| |
Call Number |
c:irua:126000 |
Serial |
2994 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Ben Dkhil, S.; Pfannmöller, M.; Bals, S.; Koganezawa, T.; Yoshimoto, N.; Hannani, D.; Gaceur, M.; Videlot-Ackermann, C.; Margeat, O.; Ackermann, J. |
|
| |
Title |
Square-centimeter-sized high-efficiency polymer solar cells : how the processing atmosphere and film quality influence performance at large scale |
Type |
A1 Journal article |
| |
Year |
2016 |
Publication |
Laser physics review |
Abbreviated Journal |
Adv Energy Mater |
|
| |
Volume |
6 |
Issue |
6 |
Pages |
1600290 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
Organic solar cells based on two benzodithiophene-based polymers (PTB7 and PTB7-Th) processed at square centimeter-size under inert atmosphere and ambient air, respectively, are investigated. It is demonstrated that the performance of solar cells processed under inert atmosphere is not limited by the upscaling of photoactive layer and the interfacial layers. Thorough morphological and electrical characterizations of optimized layers and corresponding devices reveal that performance losses due to area enlargement are only caused by the sheet resistance of the transparent electrode reducing the effi ciency from 9.3% of 7.8% for PTB7-Th in the condition that both photoactive layer and the interfacial layers are of high layer quality. Air processing of photoactive layer and the interfacial layers into centimeter-sized solar cells lead to additional, but only slight, losses (< 10%) in all photovoltaic parameters, which can be addressed to changes in the electronic properties of both active layer and ZnO layers rather than changes in layer morphology. The demonstrated compatibility of polymer solar cells using solution-processed photoactive layer and interfacial layers with large area indicates that the introduction of a standard active area of 1 cm(2) for measuring effi ciency of organic record solar cells is feasible. However electric standards for indium tin oxides (ITO) or alternative transparent electrodes need to be developed so that performance of new photovoltaic materials can be compared at square centimeter-size. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
Place of publication unknown |
Editor |
|
|
| |
Language |
|
Wos |
000379314700010 |
Publication Date |
2016-05-04 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1614-6832 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
16.721 |
Times cited |
6 |
Open Access |
Not_Open_Access |
|
| |
Notes |
; The authors acknowledge financial support by the French Fond Unique Intermisteriel (FUI) under the project “SFUMATO” (Grant number: F1110019V/ 201308815) as well as by the European Commission under the Project “SUNFLOWER” (FP7-ICT-2011-7-contract no. 287594). Generalitat Valenciana (ISIC/2012/008 Institute of Nanotechnologies for Clean Energies) is also acknowledged for providing financial support. The synchrotron radiation experiments were performed at BL46XU and BL19B2 in SPring-8 with the approval of Japan Synchrotron Radiation Research Institute (JASRI) (Proposal Nos. 2014B1916 and 2015A1984). The authors further acknowledge financial support from the European Research Council (ERC Starting Grant #335078-COLOURATOMS). ; |
Approved |
Most recent IF: 16.721 |
|
| |
Call Number |
UA @ lucian @ c:irua:134951 |
Serial |
4249 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Ben Dkhil, S.; Pfannmöller, M.; Saba, M.I.; Gaceur, M.; Heidari, H.; Videlot-Ackermann, C.; Margeat, O.; Guerrero, A.; Bisquert, J.; Garcia-Belmonte, G.; Mattoni, A.; Bals, S.; Ackermann, J. |
|
| |
Title |
Toward high-temperature stability of PTB7-based bulk heterojunction solar cells : impact of fullerene size and solvent additive |
Type |
A1 Journal article |
| |
Year |
2017 |
Publication |
Laser physics review |
Abbreviated Journal |
Adv Energy Mater |
|
| |
Volume |
7 |
Issue |
7 |
Pages |
1601486 |
|
| |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
| |
Abstract |
The use of fullerene as acceptor limits the thermal stability of organic solar cells at high temperatures as their diffusion inside the donor leads to phase separation via Ostwald ripening. Here it is reported that fullerene diffusion is fully suppressed at temperatures up to 140 degrees C in bulk heterojunctions based on the benzodithiophene-based polymer (the poly[[4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b: 4,5-b']dithiophene-2,6-diyl][3-fluoro-2-[(2-ethylhexyl) carbonyl]thieno[3,4-b]thiophenediyl]], (PTB7) in combination with the fullerene derivative [6,6]-phenyl-C71-butyric acid methyl ester (PC70BM). The blend stability is found independently of the presence of diiodooctane (DIO) used to optimize nanostructuration and in contrast to PTB7 blends using the smaller fullerene derivative PC70BM. The unprecedented thermal stability of PTB7: PC70BM layers is addressed to local minima in the mixing enthalpy of the blend forming stable phases that inhibit fullerene diffusion. Importantly, although the nanoscale morphology of DIO processed blends is thermally stable, corresponding devices show strong performance losses under thermal stress. Only by the use of a high temperature annealing step removing residual DIO from the device, remarkably stable high efficiency solar cells with performance losses less than 10% after a continuous annealing at 140 degrees C over 3 days are obtained. These results pave the way toward high temperature stable polymer solar cells using fullerene acceptors. |
|
| |
Address |
|
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
|
Place of Publication |
Place of publication unknown |
Editor |
|
|
| |
Language |
|
Wos |
000396328500009 |
Publication Date |
2016-11-07 |
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1614-6832; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
| |
Impact Factor |
16.721 |
Times cited |
27 |
Open Access |
Not_Open_Access |
|
| |
Notes |
; The authors acknowledge financial support by the French Fond Unique Interministeriel (FUI) under the project “SFUMATO” (grant number: F1110019V/ 201308815) as well as by the European Commission under the Project “SUNFLOWER” (FP7-ICT-2011-7, grant number: 287594). Generalitat Valenciana (ISIC/2012/008 Institute of Nanotechnologies for Clean Energies) is also acknowledged for providing financial support. The authors further acknowledge financial support via ERC Starting Grant Colouratoms (335078). ; |
Approved |
Most recent IF: 16.721 |
|
| |
Call Number |
UA @ lucian @ c:irua:141991UA @ admin @ c:irua:141991 |
Serial |
4697 |
|
| Permanent link to this record |
