|
Records |
Links |
|
Author |
Huyskens, C.; Lenaerts, S.; Brauns, E.; Diels, L.; de Wever, H. |
|
|
Title |
Study of (ir)reversible fouling in MBRs under various operating conditions using new on-line fouling sensor |
Type |
A1 Journal article |
|
Year |
2011 |
Publication |
Separation and purification technology |
Abbreviated Journal |
Sep Purif Technol |
|
|
Volume |
81 |
Issue |
2 |
Pages |
208-215 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
In this study, a new fouling sensor was validated under different conditions of hydraulic (HRT) and sludge retention time (SRT). The MBR-VFM (membrane bioreactor-VITO Fouling Measurement) allows the simultaneous determination of the physically reversible and irreversible fouling potential of a mixed liquor during a single crossflow filtration test. In accordance with the on-line filtration behavior, the measured reversible and irreversible fouling propensities differed significantly between MBRs operated at different combinations of HRT-SRT. Moreover, a significant negative correlation was found between the on-line permeability and the reversible and irreversible fouling propensity measured by the MBR-VFM. This corresponded to observations made on membrane recovery after physical or chemical cleaning actions. Higher reversible and irreversible fouling were observed at lower HRT, presumably as a consequence of increased concentrations of foulants present. The effect of SRT was much smaller and restricted to the reversible fouling component. Possible explanations for the increased fouling at prolonged SRT are the higher sludge and colloid concentration and the smaller floc size. It can be concluded that the MBR-VFM is a useful tool to monitor fluctuations in a mixed liquors (ir)reversible fouling potential and can contribute to a deeper understanding of the occurring fouling phenomena. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000296108500012 |
Publication Date |
2011-08-01 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1383-5866 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
3.359 |
Times cited |
15 |
Open Access |
|
|
|
Notes |
; ; |
Approved |
Most recent IF: 3.359; 2011 IF: 2.921 |
|
|
Call Number |
UA @ admin @ c:irua:93410 |
Serial |
5992 |
|
Permanent link to this record |
|
|
|
|
Author |
Caratelli, D.; Gielis, J.; Natalini, P.; Ricci, P.E.; Tavkhelidze, I. |
|
|
Title |
The Robin problem for the Helmholtz equation in a starlike planar domain |
Type |
A1 Journal article |
|
Year |
2011 |
Publication |
Georgian mathematical journal |
Abbreviated Journal |
|
|
|
Volume |
18 |
Issue |
3 |
Pages |
465-479 |
|
|
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
The interior and exterior Robin problems for the Helmholtz equation in starlike planar domains are addressed by using a suitable Fourier-like technique. Attention is in particular focused on normal-polar domains whose boundaries are defined by the so-called superformula introduced by J. Gielis. A dedicated numerical procedure based on the computer algebra system Mathematica© is developed in order to validate the proposed approach. In this way, highly accurate approximations of the solution, featuring properties similar to the classical ones, are obtained. The computed results are found to be in good agreement with the theoretical findings on Fourier series expansion presented by L. Carleson. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000296166100004 |
Publication Date |
2021-02-28 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1072-947x |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
|
Times cited |
|
Open Access |
|
|
|
Notes |
|
Approved |
no |
|
|
Call Number |
UA @ admin @ c:irua:91086 |
Serial |
8658 |
|
Permanent link to this record |
|
|
|
|
Author |
Jammaer, J.; Aprile, C.; Verbruggen, S.W.; Lenaerts, S.; Pescarmona, P.P.; Martens, J.A. |
|
|
Title |
A non-aqueous synthesis of TiO2SiO2 composites in supercritical CO2 for the photodegradation of pollutants |
Type |
A1 Journal article |
|
Year |
2011 |
Publication |
Chemsuschem |
Abbreviated Journal |
Chemsuschem |
|
|
Volume |
4 |
Issue |
10 |
Pages |
1457-1463 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Titania/silica composites with different Ti/Si ratios are synthesized via a nonconventional synthesis route. The synthesis involves non-aqueous reaction of metal alkoxides and formic acid at 75 °C in supercritical carbon dioxide. The as-prepared composite materials contain nanometer-sized anatase crystallites and amorphous silica. Large specific surface areas are obtained. The composites are evaluated in the photocatalytic degradation of phenol in aqueous medium, and in the elimination of acetaldehyde from air. The highest photocatalytic activity in both processes is achieved with a composite containing 40 wt % TiO2. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000296497400010 |
Publication Date |
2011-05-20 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1864-5631 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
7.226 |
Times cited |
15 |
Open Access |
|
|
|
Notes |
; The authors acknowledge sponsorship from CECAT and Methusalem (long-term financing of the Flemish government). We thank Dr. E. Gobechiya for assistance with XRD measurements and A. Lemaire for assistance with mercury porosimetry measurements. ; |
Approved |
Most recent IF: 7.226; 2011 IF: 6.827 |
|
|
Call Number |
UA @ admin @ c:irua:93363 |
Serial |
5973 |
|
Permanent link to this record |
|
|
|
|
Author |
Verbruggen, S.W.; Ribbens, S.; Tytgat, T.; Hauchecorne, B.; Smits, M.; Meynen, V.; Cool, P.; Martens, J.A.; Lenaerts, S. |
|
|
Title |
The benefit of glass bead supports for efficient gas phase photocatalysis : case study of a commercial and a synthesised photocatalyst |
Type |
A1 Journal article |
|
Year |
2011 |
Publication |
Chemical engineering journal |
Abbreviated Journal |
Chem Eng J |
|
|
Volume |
174 |
Issue |
1 |
Pages |
318-325 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Laboratory of adsorption and catalysis (LADCA); Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
In the field of photocatalytic air purification, the immobilisation of catalyst particles on support surfaces without loss of photon efficiency is an important challenge. Therefore, an immobilisation method involving a one-step suspension coating of pre-synthesised photocatalysts on glass beads was applied. The various benefits are exemplified in the gas phase photodegradation of ethylene. Coating of glass beads is easy, fast, cheap and offers a more efficient alternative to bulk catalyst pellets. Furthermore, this coating procedure allows to use porous, pre-synthesised catalysts to their full potential, as the surface area and morphology of the initial powder is barely altered after coating, in strong contrast to pelletising. With this technique it became possible to study the gas phase photocatalytic activity of commercial titanium dioxide, trititanate nanotubes and mixed phase anatase/trititanate nanotubes in a packed bed reactor towards the degradation of ethylene without changing the catalyst properties. Coating of glass beads with the photocatalyst revealed the superior activity of the as-prepared nanotubes, compared to TiO2 Aerolyst® 7710 in gaseous phase. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000296950300041 |
Publication Date |
2011-09-17 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1385-8947; 1873-3212 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
6.216 |
Times cited |
39 |
Open Access |
|
|
|
Notes |
; The author wishes to acknowledge the Research Foundation of Flanders (FWO) for the financial support. Evonik is greatly thanked for supplying the TiO<INF>2</ INF> Aerolyst (R) 7710 pellets. ; |
Approved |
Most recent IF: 6.216; 2011 IF: 3.461 |
|
|
Call Number |
UA @ admin @ c:irua:93364 |
Serial |
5929 |
|
Permanent link to this record |
|
|
|
|
Author |
Jochems, P.; Satyawali, Y.; van Roy, S.; Doyen, W.; Diels, L.; Dejonghe, W. |
|
|
Title |
Characterization and optimization of \beta-galactosidase immobilization process on a mixed-matrix membrane |
Type |
A1 Journal article |
|
Year |
2011 |
Publication |
Enzyme and microbial technology |
Abbreviated Journal |
|
|
|
Volume |
49 |
Issue |
6/7 |
Pages |
580-588 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
β-Galactosidase is an important enzyme catalyzing not only the hydrolysis of lactose to the monosaccharides glucose and galactose but also the transgalactosylation reaction to produce galacto-oligosaccharides (GOS). In this study, β-galactosidase was immobilized by adsorption on a mixed-matrix membrane containing zirconium dioxide. The maximum β-galactosidase adsorbed on these membranes was 1.6 g/m2, however, maximal activity was achieved at an enzyme concentration of around 0.5 g/m2. The tests conducted to investigate the optimal immobilization parameters suggested that higher immobilization can be achieved under extreme parameters (pH and temperature) but the activity was not retained at such extreme operational parameters. The investigations on immobilized enzymes indicated that no real shift occurred in its optimal temperature after immobilization though the activity in case of immobilized enzyme was better retained at lower temperature (5 °C). A shift of 0.5 unit was observed in optimal pH after immobilization (pH 6.5 to 7). Perhaps the most striking results are the kinetic parameters of the immobilized enzyme; while the Michaelis constant (Km) value increased almost eight times compared to the free enzyme, the maximum enzyme velocity (Vmax) remained almost constant. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000298529600015 |
Publication Date |
2011-06-26 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0141-0229 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
|
Times cited |
|
Open Access |
|
|
|
Notes |
|
Approved |
no |
|
|
Call Number |
UA @ admin @ c:irua:90060 |
Serial |
7608 |
|
Permanent link to this record |
|
|
|
|
Author |
Nikolova, I.; Janssen, S.; Vos, P.; Vrancken, K.; Mishra, V.; Berghmans, P. |
|
|
Title |
Dispersion modelling of traffic induced ultrafine particles in a street canyon in Antwerp, Belgium and comparison with observations |
Type |
A1 Journal article |
|
Year |
2011 |
Publication |
The science of the total environment |
Abbreviated Journal |
|
|
|
Volume |
412 |
Issue |
|
Pages |
336-343 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
The aim of this study is to investigate the dispersion of ultrafine particles and its spatial distribution in a street canyon and its neighbourhood with the 3D CFD model ENVI-met®. The performance of the model at street scale is evaluated and the importance of the boundary conditions like wind field and traffic emissions on the UFP concentration is demonstrated. To support and validate the modelled results, a short-term measurement campaign was conducted in a street canyon in Antwerp, Belgium. The UFP concentration was measured simultaneously with P-TRACK (TSI Model 8525) at four different locations in the canyon. The modelled UFP concentrations compare well with the measured data (correlation coefficient R from 0.44 to 0.93) within the standard deviation of the measurements. Despite the moderate traffic flow in the street canyon, UFP concentrations in the canyon are in general double of the background concentrations, indicating the high local contribution for this particle number concentration. Some of the observed concentration profiles are not resembled by the model simulations. For these specific anomalies, further analysis is performed and plausible explanations are put forward. The role of wind direction and traffic emissions is investigated. The performance evaluation of ENVI-met® shows that in general the model qualitatively and quantitatively describes the dispersion of UFP in the street canyon study. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000298534300038 |
Publication Date |
2011-10-28 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0048-9697; 1879-1026 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
|
Times cited |
|
Open Access |
|
|
|
Notes |
|
Approved |
no |
|
|
Call Number |
UA @ admin @ c:irua:94377 |
Serial |
7815 |
|
Permanent link to this record |
|
|
|
|
Author |
De Schepper, V.C.J.; Holvoet, K.M.A.; Benedetti, L.; Seuntjens, P.; Vanrolleghem, P.A. |
|
|
Title |
Extension of the river water quality model no. 1 with the fate of pesticides |
Type |
A1 Journal article |
|
Year |
2012 |
Publication |
Journal of hydroinformatics |
Abbreviated Journal |
|
|
|
Volume |
14 |
Issue |
1 |
Pages |
48-64 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
The existing River Water Quality Model No. 1 (RWQM1) was extended with processes determining the fate of non-volatile pesticides in the water phase and sediments. The exchange of pesticides between the water column and the sediment is described by three transport processes: diffusion, sedimentation and resuspension. Burial of sediments is also included. The modified model was used to simulate the concentrations of diuron and chloridazon in the river Nil. A good agreement was found between the simulated pesticide concentrations and measured values resulting from a four-month intensive monitoring campaign. The simulation results indicate that pesticide concentrations in the bulk water are not sensitive to the selected biochemical model parameters. it seems that these concentrations are mainly determined by the imposed upstream concentrations, run-off and direct losses. The high concentrations in the bulk water were not observed in the sediment pore water due to a limited exchange between the water column and the sediment. According to a sensitivity analysis, the observed pesticide concentrations are highly sensitive to the diffusion and sorption coefficients. Therefore, model users should determine these parameters with accuracy in order to reduce the degree of uncertainty in their results. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000298618300004 |
Publication Date |
2011-10-25 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1464-7141 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
|
Times cited |
|
Open Access |
|
|
|
Notes |
|
Approved |
no |
|
|
Call Number |
UA @ admin @ c:irua:96257 |
Serial |
7954 |
|
Permanent link to this record |
|
|
|
|
Author |
Buytaert, V.; Muys, B.; Devriendt, N.; Pelkmans, L.; Kretzschmar, J.G.; Samson, R. |
|
|
Title |
Towards integrated sustainability assessment for energetic use of biomass : a state of the art evaluation of assessment tools |
Type |
A1 Journal article |
|
Year |
2011 |
Publication |
Renewable and sustainable energy reviews |
Abbreviated Journal |
|
|
|
Volume |
15 |
Issue |
8 |
Pages |
3918-3933 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Biomass is expected to play an increasingly significant role in the greening of energy supply. Nevertheless, concerns are rising about the sustainability of large-scale energy crop production. Impacts must be assessed carefully before deciding whether and how this industry should be developed, and what technologies, policies and investment strategies should be pursued. There is need for a comprehensive and reliable sustainability assessment tool to evaluate the environmental, social and economic performance of biomass energy production. This paper paves the way for such a tool by analysing and comparing the performance and applicability of a selection of existing tools that are potentially useful for sustainability assessment of bioenergy systems. The selected tools are: Criteria And Indicators (C&I), Life Cycle Assessment (LCA), Environmental Impact Assessment (EIA), Cost Benefit Analysis (CBA), Exergy Analysis (EA) and System Perturbation Analysis (SPA). To evaluate the tools, a framework was constructed that consists of four evaluation levels: sustainability issues, tool attributes, model structure, area of application. The tools were then evaluated using literature data and with the help of a Delphi panel of experts. Finally, a statistical analysis was performed on the resulting data matrix to detect significant differences between tools. It becomes clear that none of the selected tools is able to perform a comprehensive sustainability assessment of bioenergy systems. Every tool has its particular advantages and disadvantages, which means that trade-offs are inevitable and a balance must be found between scientific accuracy and pragmatic decision making. A good definition of the assessment objective is therefore crucial. It seems an interesting option to create a toolbox that combines procedural parts of C&I and EIA, supplemented with calculation algorithms of LCA and CBA for respectively environmental and economic sustainability indicators. Nevertheless, this would require a more comprehensive interdisciplinary approach to align the different tool characteristics and focuses. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000298764100043 |
Publication Date |
2011-08-06 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1364-0321; 1879-0690 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
|
Times cited |
|
Open Access |
|
|
|
Notes |
|
Approved |
no |
|
|
Call Number |
UA @ admin @ c:irua:96444 |
Serial |
8682 |
|
Permanent link to this record |
|
|
|
|
Author |
Smits, M.; Vanpachtenbeke, F.; Horemans, B.; De Wael, K.; Hauchecorne, B.; Van Langenhove, H.; Demeestere, K.; Lenaerts, S. |
|
|
Title |
Effect of operating and sampling conditions on the exhaust gas composition of small-scale power generators |
Type |
A1 Journal article |
|
Year |
2012 |
Publication |
PLoS ONE |
Abbreviated Journal |
Plos One |
|
|
Volume |
7 |
Issue |
3 |
Pages |
e32825-e32825,10 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Small stationary diesel engines, like in generator sets, have limited emission control measures and are therefore responsible for 44% of the particulate matter (PM) emissions in the United States. The diesel exhaust composition depends on operating conditions of the combustion engine. Furthermore, the measurements are influenced by the used sampling method. This study examines the effect of engine loading and exhaust gas dilution on the composition of small-scale power generators. These generators are used in different operating conditions than road-transport vehicles, resulting in different emission characteristics. Experimental data were obtained for gaseous volatile organic compounds (VOC) and PM mass concentration, elemental composition and nitrate content. The exhaust composition depends on load condition because of its effect on fuel consumption, engine wear and combustion temperature. Higher load conditions result in lower PM concentration and sharper edged particles with larger aerodynamic diameters. A positive correlation with load condition was found for K, Ca, Sr, Mn, Cu, Zn and Pb adsorbed on PM, elements that originate from lubricating oil or engine corrosion. The nitrate concentration decreases at higher load conditions, due to enhanced nitrate dissociation to gaseous NO at higher engine temperatures. Dilution on the other hand decreases PM and nitrate concentration and increases gaseous VOC and adsorbed metal content. In conclusion, these data show that operating and sampling conditions have a major effect on the exhaust gas composition of small-scale diesel generators. Therefore, care must be taken when designing new experiments or comparing literature results. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000303836500012 |
Publication Date |
2012-03-19 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1932-6203 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.806 |
Times cited |
5 |
Open Access |
|
|
|
Notes |
; ; |
Approved |
Most recent IF: 2.806; 2012 IF: 3.730 |
|
|
Call Number |
UA @ admin @ c:irua:96545 |
Serial |
5581 |
|
Permanent link to this record |
|
|
|
|
Author |
Tytgat, T.; Hauchecorne, B.; Smits, M.; Verbruggen, S.; Lenaerts, S. |
|
|
Title |
Concept and validation of a fully automated photocatalytic test setup |
Type |
A1 Journal article |
|
Year |
2012 |
Publication |
Journal of laboratory automation |
Abbreviated Journal |
Jala-J Lab Autom |
|
|
Volume |
17 |
Issue |
2 |
Pages |
134-143 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Photocatalytic activity can be studied by several methods, each with its own strengths and weaknesses. To study photocatalytic activity in an easy, user-friendly, and realistic way, a completely new setup has been built. The setup is modularly constructed around Fourier transform infrared spectroscopy (FTIR) spectroscopy at the heart of it, resulting in great versatility. Complementary software has been written for automatic control of the setup and for processing the generated data. Two pollutants, oil and n-octane, are tested to validate the performance of the setup. These validation experiments confirm the usefulness and added value of the setup in general and of the FTIR detection methodology as well. It becomes clear that a system of online measurements with good repeatability, accuracy, and user-friendliness has been created. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000304775300006 |
Publication Date |
2014-07-23 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2211-0682 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.85 |
Times cited |
15 |
Open Access |
|
|
|
Notes |
; The authors disclosed receipt of the following financial support for the research and/or authorship of this article: This work was supported by a Ph.D. grant (T. Tytgat) funded by the Institute of Innovation by Science and Technology in Flanders (IWT) and by a Ph.D. grant (S. Verbruggen) from the Research Foundation of Flanders (FWO). Other funding was made possible by the University of Antwerp. ; |
Approved |
Most recent IF: 2.85; 2012 IF: 1.457 |
|
|
Call Number |
UA @ admin @ c:irua:96649 |
Serial |
5935 |
|
Permanent link to this record |
|
|
|
|
Author |
Mishra, V.K.; Kumar, P.; Van Poppel, M.; Bleux, N.; Frijns, E.; Reggente, M.; Berghmans, P.; Int Panis, L.; Samson, R. |
|
|
Title |
Wintertime spatio-temporal variation of ultrafine particles in a Belgian city |
Type |
A1 Journal article |
|
Year |
2012 |
Publication |
The science of the total environment |
Abbreviated Journal |
|
|
|
Volume |
431 |
Issue |
|
Pages |
307-313 |
|
|
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Simultaneous measurements of ultrafine particles (UFPs) were carried out at four sampling locations situated within a 1 km(2) grid area in a Belgian city, Borgerhout (Antwerp). All sampling sites had different orientation and height of buildings and dissimilar levels of anthropogenic activities (mainly traffic volume). The aims were to investigate: (i) the spatio-temporal variation of UFP within the area, (ii) the effect of wind direction with respect to the volume of traffic on UFP levels, and (iii) the spatial representativeness of the official monitoring station situated in the study area. All sampling sites followed similar diurnal patterns of UFP variation, but effects of local traffic emissions were evident. Wind direction also had a profound influence on UFP concentrations at certain sites. The results indicated a clear influence of local weather conditions and the more dominant effect of traffic volumes. Our analysis indicated that the regional air quality monitoring station represented the other sampling sites in the study area reasonably well; temporal patterns were found to be comparable though the absolute average concentrations showed differences of up to 35%. (C) 2012 Elsevier B.V. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000306887900037 |
Publication Date |
2012-06-14 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0048-9697; 1879-1026 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
|
Times cited |
|
Open Access |
|
|
|
Notes |
|
Approved |
no |
|
|
Call Number |
UA @ admin @ c:irua:101123 |
Serial |
8759 |
|
Permanent link to this record |
|
|
|
|
Author |
Huyskens, C.; De Wever, H.; Fovet, Y.; Wegmann, U.; Diels, L.; Lenaerts, S. |
|
|
Title |
Screening of novel MBR fouling reducers : benchmarking with known fouling reducers and evaluation of their mechanism of action |
Type |
A1 Journal article |
|
Year |
2012 |
Publication |
Separation and purification technology |
Abbreviated Journal |
Sep Purif Technol |
|
|
Volume |
95 |
Issue |
|
Pages |
49-57 |
|
|
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
A novel fouling characterization method was applied for a first screening of two novel synthetic flocculants developed by BASF (BASF-1 and BASF-2) and benchmarking with six well-known products. Results showed that this MBR-VITO Fouling Measurement (VFM) was able to identify beneficial and adverse effects of different additives on the mixed liquor's reversible and irreversible fouling and, in combination with supporting mixed liquor analyses, allowed to identify the additive's main working mechanism. The first screening tests indicated that BASF-1 and BASF-2 reduced reversible and irreversible fouling to a similar extent as the known synthetic flocculants due to a charge neutralization mechanism, resulting in enhanced flocculation and SMP removal. Further testing at different additive concentrations provided a first indication of the optimal dosage and revealed a considerable risk of overdosing for BASF-2, rendering it less suited for fouling control. In contrast, such adverse effects were not observed for BASF-1. BASF-1 induced similar beneficial effects as the known MPE50 polymer at lower dosage and was therefore considered promising for application in MBRs. (C) 2012 Elsevier B.V. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000307032100008 |
Publication Date |
2012-04-26 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1383-5866 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
3.359 |
Times cited |
24 |
Open Access |
|
|
|
Notes |
; The authors would like to thank K. Luyckx, J. Fret, L. Heylen, R. Muyshondt, H. Sterckx, J. Verheyden and J. Vande-Velden for technical assistance and V. Iversen for kindly supplying some of the commercial additives. Celine Huyskens is indebted to the Research Foundation-Flanders (FWO). The European Commission is acknowledged for financial support to Aquafit4use (FP7, Grant 211534). ; |
Approved |
Most recent IF: 3.359; 2012 IF: 2.894 |
|
|
Call Number |
UA @ admin @ c:irua:101903 |
Serial |
5990 |
|
Permanent link to this record |
|
|
|
|
Author |
Van Noyen, J.; Middelkoop, V.; Buysse, C.; Kovalevsky, A.; Snijkers, F.; Buekenhoudt, A.; Mullens, S.; Luyten, J.; Kretzschmar, J.; Lenaerts, S. |
|
|
Title |
Fabrication of perovskite capillary membranes for high temperature gas separation |
Type |
A1 Journal article |
|
Year |
2012 |
Publication |
Catalysis today |
Abbreviated Journal |
Catal Today |
|
|
Volume |
193 |
Issue |
1 |
Pages |
172-178 |
|
|
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Oxygen-permeable perovskites with mixed ionic-electronic conducting properties can play an important role in carbon capture and storage techniques. Their ability to separate oxygen from air is needed, more specifically, in oxy-fuel and pre-combustion technologies. In this work, the first detailed comparative analysis and new results are reported on four types of Ba0.5Sr0.5Co0.8Fe0.2O3-delta (BSCF) capillary membranes: non-coated sulphur-containing; catalyst-coated sulphur-containing; non-coated sulphur-free and catalyst-coated sulphur-free. The fabrication of BSCF capillaries by a spinning technique based on phase inversion is further discussed and their oxygen separation performances are interpreted. The comparison of the performance of these different generations of BSCF capillaries of similar dimensions demonstrates a significant impact of the sulphur contamination on both the oxygen flux through the membrane and the activation energy of the overall oxygen transport mechanism. Careful attention is paid to the effect of activation layers on both sulphur-free and sulphur-containing types of capillaries. Additional long-term testing of the sulphur-free BSCF capillaries is presented, where partial decomposition of the membrane surface was observed due to kinetic demixing. (c) 2012 Elsevier B.V. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000308675900025 |
Publication Date |
2012-04-15 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0920-5861 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
4.636 |
Times cited |
9 |
Open Access |
|
|
|
Notes |
; The authors want to express their thanks to the VITO personnel for their continuous support, especially B. Molenberghs, W. Doyen (Separation and Conversion Technology, VITO), R. Kemps, M. Mertens, I. Thijs, M. Schoeters, W. Bouwen and J. Cooymans (Materials Department, VITO). C. Buysse thankfully acknowledges a Ph.D. scholarship provided by VITO and the University of Antwerp. This work is performed in the framework of the German Helmholtz Alliance Project “MEM-BRAIN”, aiming at the development of gas separation membranes for zero-emission fossil fuel power plants. ; |
Approved |
Most recent IF: 4.636; 2012 IF: 2.980 |
|
|
Call Number |
UA @ admin @ c:irua:101797 |
Serial |
5951 |
|
Permanent link to this record |
|
|
|
|
Author |
Fenu, A.; De Wilde, W.; Gaertner, M.; Weemaes, M.; de Gueldre, G.; van de Steene, B. |
|
|
Title |
Elaborating the membrane life concept in a full scale hollow-fibers MBR |
Type |
A1 Journal article |
|
Year |
2012 |
Publication |
Journal of membrane science |
Abbreviated Journal |
|
|
|
Volume |
421 |
Issue |
|
Pages |
349-354 |
|
|
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
The membrane life-time has a strong impact on competitivity and viability of MBRs. This study critically analyzes the membrane life-time concept, approaching it through different assessment methods. A full scale MBR's membrane life-time was assessed on the following: (i) maintaining the permeate flow throughput to the MBR; (ii) the permeability decline; (iii) oxidative aging; (iv) the increase in energy costs; and (v) mechanical aging. The method based on permeability decline provides a membrane life-time estimate up to a theoretical end. It was further elaborated inherently to operations with no long-term flux decline. The increase in operating pressure remains the main end-of-life trigger for deciding when to replace membrane modules. On the contrary, mechanical and permeate flow throughput analysis of the data are not able to provide a clear estimate of the membrane life-time. As for the membrane life-time estimation based on chlorine contact, it was found to be too optimistic. Complete irreversible fouling occurs before maximum contact time with chlorine is reached. At end-of-life operating conditions, the energy consumption raised of 170% due to the reduced flow rate. The cost raise appears high but still affordable. Earlier membrane replacement thus can never be counterbalanced by energy costs saving. (C) 2012 Elsevier B.V. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000308741100039 |
Publication Date |
2012-08-07 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0376-7388 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
|
Times cited |
|
Open Access |
|
|
|
Notes |
|
Approved |
no |
|
|
Call Number |
UA @ admin @ c:irua:101790 |
Serial |
7856 |
|
Permanent link to this record |
|
|
|
|
Author |
Vos, P.E.J.; Nikolova, I.; Janssen, S. |
|
|
Title |
A high-order model for accurately simulating the size distribution of ultrafine particles in a traffic tunnel |
Type |
A1 Journal article |
|
Year |
2012 |
Publication |
Atmospheric environment : an international journal |
Abbreviated Journal |
|
|
|
Volume |
59 |
Issue |
|
Pages |
415-425 |
|
|
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
We present a computational model for simulating the dispersion of traffic emitted particulate matter inside a road tunnel, with an emphasis on the number concentration of ultrafine particles (UFP). The model primarily calculates the size distribution of the particle number concentration at each location inside the tunnel. The proposed model differs from existing models in the sense that it uses a continuous representation of the size distribution based upon the high-order finite element method and that it solves the governing equations using the state-of-the-art discontinuous Galerkin method. Next to the traditional transport processes, the model also implements the most important aerosol transformation processes such as coagulation, condensation and dry deposition. It is shown that based upon parametrisations found in literature, the process of condensation in a traffic tunnel cannot properly be modelled. Therefore, we present a correction factor that allows for a better parametrisation. The adequate performance of the model is demonstrated by both a verification study and a validation study. For the verification we show that the discretisation error converges consistently while for the validation we compare the modelled results with a suitable set of data from a UFP measurement campaign in a Taiwanese traffic tunnel. The model is shown to correctly simulate the observed behaviour and by applying a statistical model evaluation we demonstrate that the proposed model meets widely accepted air quality model acceptance criteria. (C) 2012 Elsevier Ltd. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000309081100047 |
Publication Date |
2012-05-25 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1352-2310 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
|
Times cited |
|
Open Access |
|
|
|
Notes |
|
Approved |
no |
|
|
Call Number |
UA @ admin @ c:irua:101793 |
Serial |
8033 |
|
Permanent link to this record |
|
|
|
|
Author |
Gielis, J.; Caratelli, D.; Fougerolle, Y.; Ricci, P.E.; Tavkelidze, I.; Gerats, T. |
|
|
Title |
Universal natural shapes : from unifying shape description to simple methods for shape analysis and boundary value problems |
Type |
A1 Journal article |
|
Year |
2012 |
Publication |
PLoS ONE |
Abbreviated Journal |
|
|
|
Volume |
7 |
Issue |
9 |
Pages |
e29324-11 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Gielis curves and surfaces can describe a wide range of natural shapes and they have been used in various studies in biology and physics as descriptive tool. This has stimulated the generalization of widely used computational methods. Here we show that proper normalization of the Levenberg-Marquardt algorithm allows for efficient and robust reconstruction of Gielis curves, including self-intersecting and asymmetric curves, without increasing the overall complexity of the algorithm. Then, we show how complex curves of k-type can be constructed and how solutions to the Dirichlet problem for the Laplace equation on these complex domains can be derived using a semi-Fourier method. In all three methods, descriptive and computational power and efficiency is obtained in a surprisingly simple way. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000309517500001 |
Publication Date |
2012-09-30 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1932-6203 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
|
Times cited |
|
Open Access |
|
|
|
Notes |
|
Approved |
no |
|
|
Call Number |
UA @ admin @ c:irua:102202 |
Serial |
8711 |
|
Permanent link to this record |
|
|
|
|
Author |
Haest, P.J.; Springael, D.; Seuntjens, P.; Smolders, E. |
|
|
Title |
Self-inhibition can limit biologically enhanced TCE dissolution from a TCE DNAPL |
Type |
A1 Journal article |
|
Year |
2012 |
Publication |
Chemosphere |
Abbreviated Journal |
|
|
|
Volume |
89 |
Issue |
11 |
Pages |
1369-1375 |
|
|
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Biodegradation of trichloroethene (TCE) near a Dense Non Aqueous Phase Liquid (DNAPL) can enhance the dissolution rate of the DNAPL by increasing the concentration gradient at the DNAPL-water interface. Two-dimensional flow-through sand boxes containing a ICE DNAPL and inoculated with a TCE dechlorinating consortium were set up to measure this bio-enhanced dissolution under anaerobic conditions. The total mass of TCE and daughter products in the effluent of the biotic boxes was 3-6 fold larger than in the effluent of the abiotic box. However, the mass of daughter products only accounted for 19-55% of the total mass of chlorinated compounds in the effluent, suggesting that bio-enhanced dissolution factors were maximally 1.3-2.2. The enhanced dissolution most likely primarily resulted from variable DNAPL distribution rather than biodegradation. Specific dechlorination rates previously determined in a stirred liquid medium were used in a reactive transport model to identify the rate limiting factors. The model adequately simulated the overall TCE degradation when predicted resident microbial numbers approached observed values and indicated an enhancement factor for TCE dissolution of 1.01. The model shows that dechlorination of TCE in the 20 box was limited due to the short residence time and the self-inhibition of the TCE degradation. A parameter sensitivity analysis predicts that the bio-enhanced dissolution factor for this TCE source zone can only exceed a value of 2 if the TCE self-inhibition is drastically reduced (when a TCE tolerant dehalogenating community is present) or if the DNAPL is located in a low-permeable layer with a small Darcy velocity. (C) 2012 Elsevier Ltd. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000310112600015 |
Publication Date |
2012-06-30 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0045-6535; 1879-1298 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
|
Times cited |
|
Open Access |
|
|
|
Notes |
|
Approved |
no |
|
|
Call Number |
UA @ admin @ c:irua:102142 |
Serial |
8512 |
|
Permanent link to this record |
|
|
|
|
Author |
Verbruggen, S.W.; Masschaele, K.; Moortgat, E.; Korany, T.E.; Hauchecorne, B.; Martens, J.A.; Lenaerts, S. |
|
|
Title |
Factors driving the activity of commercial titanium dioxide powders towards gas phase photocatalytic oxidation of acetaldehyde |
Type |
A1 Journal article |
|
Year |
2012 |
Publication |
Catalysis science & technology |
Abbreviated Journal |
Catal Sci Technol |
|
|
Volume |
2 |
Issue |
11 |
Pages |
2311-2318 |
|
|
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
The photocatalytic activity of two commercial titanium dioxide powders (Cristal Global, Millennium PC500 and Evonik, P25) is compared towards acetaldehyde degradation in the gas phase. In contrast to the extensive literature available, we found a higher activity for the PC500 than for the P25 coating. Here, we present a comprehensive characterization of the bulk and surface properties of both powders. Our comparison shows that the material properties that dominate the overall photocatalytic activity in gas phase differ from those required for the photodegradation of water-borne pollutants. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000310863900020 |
Publication Date |
2012-06-13 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2044-4753; 2044-4761 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
5.773 |
Times cited |
33 |
Open Access |
|
|
|
Notes |
; S.W.V. acknowledges the Research Foundation of Flanders (FWO) for the financial support. J.A.M acknowledges long term funding (Methusalem). ; |
Approved |
Most recent IF: 5.773; 2012 IF: 3.753 |
|
|
Call Number |
UA @ admin @ c:irua:105162 |
Serial |
5952 |
|
Permanent link to this record |
|
|
|
|
Author |
Tytgat, T.; Hauchecorne, B.; Abakumov, A.M.; Smits, M.; Verbruggen, S.W.; Lenaerts, S. |
|
|
Title |
Photocatalytic process optimisation for ethylene oxidation |
Type |
A1 Journal article |
|
Year |
2012 |
Publication |
Chemical engineering journal |
Abbreviated Journal |
Chem Eng J |
|
|
Volume |
209 |
Issue |
|
Pages |
494-500 |
|
|
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT); Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
When studying photocatalysis it is important to consider, beside the chemical approach, the engineering part related to process optimisation. To achieve this a fixed bed photocatalytic set-up consisting of different catalyst placings, in order to vary catalyst distribution, is studied. The use of a fixed quantity of catalyst placed packed or randomly distributed in the reactor, results in an almost double degradation for the distributed catalyst. Applying this knowledge leads to an improved performance with limited use of catalyst. A reactor only half filled with catalyst leads to higher degradation performance compared to a completely filled reactor. Taking into account this simple process optimisation by better distributing the catalyst a more sustainable photocatalytic air purification process is achieved. (C) 2012 Elsevier B.V. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
|
|
Language |
|
Wos |
000311190500058 |
Publication Date |
2012-08-22 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1385-8947; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
6.216 |
Times cited |
12 |
Open Access |
|
|
|
Notes |
; We are grateful for the delivered photocatalyst by Evonik as well as for the PhD grant (T. Tytgat) given by the Institute of Innovation by Science and Technology in Flanders (IWT). ; |
Approved |
Most recent IF: 6.216; 2012 IF: 3.473 |
|
|
Call Number |
UA @ lucian @ c:irua:105185 |
Serial |
2609 |
|
Permanent link to this record |
|
|
|
|
Author |
Carniato, L.; Schoups, G.; Seuntjens, P.; Van Nooten, T.; Simons, Q.; Bastiaens, L. |
|
|
Title |
Predicting longevity of iron permeable reactive barriers using multiple iron deactivation models |
Type |
A1 Journal article |
|
Year |
2012 |
Publication |
Journal of contaminant hydrology |
Abbreviated Journal |
|
|
|
Volume |
142 |
Issue |
|
Pages |
93-108 |
|
|
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
In this study we investigate the model uncertainties involved in predicting long-term permeable reactive barrier (PRB) remediation efficiency based on a lab-scale column experiment under accelerated flow conditions. A PRB consisting of 20% iron and 80% sand was simulated in a laboratory-scale column and contaminated groundwater was pumped into the column for approximately 1 year at an average groundwater velocity of 3.7E – 1 m d(-1). Dissolved contaminants (PCE. TCE, cis-DCE, trans-DCE and VC) and inorganic (Ca2+, Fe2+, TIC and pH) concentrations were measured in groundwater sampled at different times and at eight different distances along the column. These measurements were used to calibrate a multi-component reactive transport model, which subsequently provided predictions of long-term PRB efficiency under reduced flow conditions (i.e., groundwater velocity of 1.4E -3 m d(-1)), representative of a field site of interest in this study. Iron reactive surface reduction due to mineral precipitation and iron dissolution was simulated using four different models. All models were able to reasonably well reproduce the column experiment measurements, whereas the extrapolated long-term efficiency under different flow rates was significantly different between the different models. These results highlight significant model uncertainties associated with extrapolating long-term PRB performance based on lab-scale column experiments. These uncertainties should be accounted for at the PRB design phase, and may be reduced by independent experiments and field observations aimed at a better understanding of reactive surface deactivation mechanisms in iron PRBs. (C) 2012 Elsevier B.V. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000312753000009 |
Publication Date |
2012-09-13 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0169-7722 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
|
Times cited |
|
Open Access |
|
|
|
Notes |
|
Approved |
no |
|
|
Call Number |
UA @ admin @ c:irua:106010 |
Serial |
8402 |
|
Permanent link to this record |
|
|
|
|
Author |
Smits, M.; Ling, Y.; Lenaerts, S.; Van Doorslaer, S. |
|
|
Title |
Photocatalytic removal of soot : unravelling of the reaction mechanism by EPR and in situ FTIR spectroscopy |
Type |
A1 Journal article |
|
Year |
2012 |
Publication |
ChemPhysChem : a European journal of chemical physics and physical chemistry |
Abbreviated Journal |
Chemphyschem |
|
|
Volume |
13 |
Issue |
18 |
Pages |
4251-4257 |
|
|
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Photocatalytic soot oxidation is studied on P25 TiO2 as an important model reaction for self-cleaning processes by means of electron paramagnetic resonance (EPR) and Fourier transform infrared (FTIR) spectroscopy. Contacting of carbon black with P25 leads on the one hand to a reduction of the local dioxygen concentration in the powder. On the other hand, the weakly adsorbed radicals on the carbon particles are likely to act as alternative traps for the photogenerated conduction-band electrons. We find furthermore that the presence of dioxygen and oxygen-related radicals is vital for the photocatalytic soot degradation. The complete oxidation of soot to CO2 is evidenced by in situ FTIR spectroscopy, no intermediate CO is detected during the photocatalytic process. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000313692600026 |
Publication Date |
2012-11-13 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1439-4235 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
3.075 |
Times cited |
9 |
Open Access |
|
|
|
Notes |
; This work was supported by the University of Antwerp (PhD grants of M. S. and Y.L.). We would like to thank Birger Hauchecorne for the scientific discussion. ; |
Approved |
Most recent IF: 3.075; 2012 IF: 3.349 |
|
|
Call Number |
UA @ admin @ c:irua:104568 |
Serial |
5980 |
|
Permanent link to this record |
|
|
|
|
Author |
Hauchecorne, B.; Lenaerts, S. |
|
|
Title |
Unravelling the mysteries of gas phase photocatalytic reaction pathways by studying the catalyst surface : a literature review of different Fourier transform infrared spectroscopic reaction cells used in the field |
Type |
A1 Journal article |
|
Year |
2013 |
Publication |
Journal of photochemistry and photobiology: C: photochemistry reviews |
Abbreviated Journal |
J Photoch Photobio C |
|
|
Volume |
14 |
Issue |
|
Pages |
72-85 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Unlike the profound knowledge of the reaction mechanisms occurring in water phase photocatalysis, still fairly little is known on the reaction mechanisms occurring on the catalyst surface when dealing with gaseous pollutants. Unfortunately, there are some differences between both reactions. For one, there are no abundant hydroxyl radicals present in the gas phase, so that possibly other species prove to be important in abating the pollutant. In order to unravel the mysteries of gas phase photocatalytic reaction pathways, in situ techniques must be used to allow the detection and identification of reaction intermediates on a working catalyst. Several techniques were already used in the past, of which Fourier transform infrared spectroscopy seems to be the most versatile. This review will therefore give a selective overview of different spectroscopic reaction cells constructed for the in situ study of photocatalytic gas phase reactions. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000314669600005 |
Publication Date |
2012-09-28 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1389-5567 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
12.317 |
Times cited |
8 |
Open Access |
|
|
|
Notes |
; The University of Antwerp is greatly acknowledged for the fellowship granted to Birger Hauchecorne. The authors would also like to thank Sammy W. Verbruggen for his help in providing several papers of interest. ; |
Approved |
Most recent IF: 12.317; 2013 IF: 11.625 |
|
|
Call Number |
UA @ admin @ c:irua:106518 |
Serial |
6001 |
|
Permanent link to this record |
|
|
|
|
Author |
Tavkhelidze, I.; Cassisa, C.; Gielis, J.; Ricci, P.E. |
|
|
Title |
About “bulky” links, generated by generalized Möbius Listing's bodies GML3n |
Type |
A1 Journal article |
|
Year |
2013 |
Publication |
Matematica e applicazioni : atti della Accademia nazionale dei Lincei |
Abbreviated Journal |
|
|
|
Volume |
24 |
Issue |
1 |
Pages |
11-38 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
In the present paper we consider the “bulky knots'' and ”bulky links'', which appear after cutting a Generalized Möbius Listing's GMLn3 body (whose radial cross section is a plane 3-symmetric figure with three vertices) along different Generalized Möbius Listing's surfaces GMLn2 situated in it. This article is aimed to investigate the number and geometric structure of the independent objects appearing after such a cutting process of GMLn3 bodies. In most cases we are able to count the indices of the resulting mathematical objects according to the known tabulation for Knots and Links of small complexity. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000316567700002 |
Publication Date |
2013-03-13 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1120-6357 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
|
Times cited |
|
Open Access |
|
|
|
Notes |
|
Approved |
no |
|
|
Call Number |
UA @ admin @ c:irua:107174 |
Serial |
7405 |
|
Permanent link to this record |
|
|
|
|
Author |
Van Eynde, E.; Tytgat, T.; Smits, M.; Verbruggen, S.W.; Hauchecorne, B.; Lenaerts, S. |
|
|
Title |
Biotemplated diatom silica-titania materials for air purification |
Type |
A1 Journal article |
|
Year |
2013 |
Publication |
Photochemical & photobiological sciences |
Abbreviated Journal |
Photoch Photobio Sci |
|
|
Volume |
12 |
Issue |
4 |
Pages |
690-695 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
We present a novel manufacture route for silicatitania photocatalysts using the diatom microalga Pinnularia sp. Diatoms self-assemble into porous silica cell walls, called frustules, with periodic micro-, meso- and macroscale features. This unique hierarchical porous structure of the diatom frustule is used as a biotemplate to incorporate titania by a solgel methodology. Important material characteristics of the modified diatom frustules under study are morphology, crystallinity, surface area, pore size and optical properties. The produced biosilicatitania material is evaluated towards photocatalytic activity for NOx abatement under UV radiation. This research is the first step to obtain sustainable, well-immobilised silicatitania photocatalysts using diatoms. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000316572500016 |
Publication Date |
2012-10-25 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1474-905x; 1474-9092 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.344 |
Times cited |
18 |
Open Access |
|
|
|
Notes |
; ; |
Approved |
Most recent IF: 2.344; 2013 IF: 2.939 |
|
|
Call Number |
UA @ admin @ c:irua:106625 |
Serial |
5930 |
|
Permanent link to this record |
|
|
|
|
Author |
Fougerolle, Y.D.; Truchetet, F.; Demonceaux, C.; Gielis, J. |
|
|
Title |
A robust evolutionary algorithm for the recovery of rational Gielis curves |
Type |
A1 Journal article |
|
Year |
2013 |
Publication |
Pattern recognition |
Abbreviated Journal |
|
|
|
Volume |
46 |
Issue |
8 |
Pages |
2078-2091 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Gielis curves (GC) can represent a wide range of shapes and patterns ranging from star shapes to symmetric and asymmetric polygons, and even self intersecting curves. Such patterns appear in natural objects or phenomena, such as flowers, crystals, pollen structures, animals, or even wave propagation. Gielis curves and surfaces are an extension of Lamé curves and surfaces (superquadrics) which have benefited in the last two decades of extensive researches to retrieve their parameters from various data types, such as range images, 2D and 3D point clouds, etc. Unfortunately, the most efficient techniques for superquadrics recovery, based on deterministic methods, cannot directly be adapted to Gielis curves. Indeed, the different nature of their parameters forbids the use of a unified gradient descent approach, which requires initial pre-processings, such as the symmetry detection, and a reliable pose and scale estimation. Furthermore, even the most recent algorithms in the literature remain extremely sensitive to initialization and often fall into local minima in the presence of large missing data. We present a simple evolutionary algorithm which overcomes most of these issues and unifies all of the required operations into a single though efficient approach. The key ideas in this paper are the replacement of the potential fields used for the cost function (closed form) by the shortest Euclidean distance (SED, iterative approach), the construction of cost functions which minimize the shortest distance as well as the curve length using R-functions, and slight modifications of the evolutionary operators. We show that the proposed cost function based on SED and R-function offers the best compromise in terms of accuracy, robustness to noise, and missing data. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000317944800002 |
Publication Date |
2013-01-29 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0031-3203 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
|
Times cited |
|
Open Access |
|
|
|
Notes |
|
Approved |
no |
|
|
Call Number |
UA @ admin @ c:irua:107181 |
Serial |
8485 |
|
Permanent link to this record |
|
|
|
|
Author |
Buysse, C.; Michielsen, B.; Middelkoop, V.; Snijkers, F.; Buekenhondt, A.; Kretzschmar, J.; Lenaerts, S. |
|
|
Title |
Modeling of the performance of BSCF capillary membranes in four-end and three-end integration mode |
Type |
A1 Journal article |
|
Year |
2013 |
Publication |
Ceramics international |
Abbreviated Journal |
Ceram Int |
|
|
Volume |
39 |
Issue |
4 |
Pages |
4113-4123 |
|
|
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Owing to their high surface-to-volume ratio, there has been an increasing research interest in mixed ionic electronic conducting (MIEC) capillary membranes for large-scale high temperature oxygen separation applications. They offer an energy-efficient solution for high temperature combustion processes in oxy-fuel and pre-combustion CO2 capture technologies used in fossil fuel power plants. In order to assess the effectiveness of these membranes in power plant applications, the impact of the geometry of Ba0.5Sr0.5Co0.8Fe0.2O3-delta (BSCF) capillaries on their performance in the three-end and four-end integration modes has been investigated and thoroughly discussed. The model's parameters were derived from four-end mode lab-scale experiments using gas-tight, macrovoid free and sulfur-free BSCF capillary membranes that were prepared by a phase-inversion spinning technique. The results of this modeling study revealed that in the four-end mode higher average oxygen fluxes and smaller total membrane areas can be obtained than in the three-end mode. This is due to the higher pO(2) gradient across the membrane wall. (C) 2012 Elsevier Ltd and Techna Group S.r.l. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000318129100084 |
Publication Date |
2012-11-09 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0272-8842 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.986 |
Times cited |
4 |
Open Access |
|
|
|
Notes |
; The authors wish to thank all the VITO staff involved in the project for their continued support, and in particular B. Molenberghs, W. Doyen, H. Beckers and S. Mullens. C. Buysse would like to acknowledge funding from VITO and the University of Antwerp for a Ph.D. studentship. This work has been performed in the framework of the German Helmholtz Alliance Project “MEM-BRAIN”, aiming at the development of gas separation membranes for zero-emission fossil fuel power plants. ; |
Approved |
Most recent IF: 2.986; 2013 IF: 2.086 |
|
|
Call Number |
UA @ admin @ c:irua:109020 |
Serial |
5971 |
|
Permanent link to this record |
|
|
|
|
Author |
Verbruggen, S.W.; Dirckx, J.J.J.; Martens, J.A.; Lenaerts, S. |
|
|
Title |
Surface photovoltage measurements : a quick assessment of the photocatalytic activity? |
Type |
A1 Journal article |
|
Year |
2013 |
Publication |
Catalysis today |
Abbreviated Journal |
Catal Today |
|
|
Volume |
209 |
Issue |
|
Pages |
215-220 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Surface photovoltage (SPV) measurements can contribute to a better understanding of electronic properties of photocatalysts under illumination. Direct linking of SPV data to the actual photocatalytic activity remains troublesome. This work aims to discuss SPV measurements from a photocatalytic point of view. By means of several application-based scenarios we illustrate that the trend between SPV and photocatalysis strongly depends on parameters such as the crystal structure, surface modifications, morphology and humidity. This makes the interpretation far from straightforward. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000319498800035 |
Publication Date |
2013-01-16 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0920-5861 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
4.636 |
Times cited |
8 |
Open Access |
|
|
|
Notes |
; ; |
Approved |
Most recent IF: 4.636; 2013 IF: 3.309 |
|
|
Call Number |
UA @ admin @ c:irua:106520 |
Serial |
5995 |
|
Permanent link to this record |
|
|
|
|
Author |
Smits, M.; Chan, C. kit; Tytgat, T.; Craeye, B.; Costarramone, N.; Lacombe, S.; Lenaerts, S. |
|
|
Title |
Photocatalytic degradation of soot deposition : self-cleaning effect on titanium dioxide coated cementitious materials |
Type |
A1 Journal article |
|
Year |
2013 |
Publication |
Chemical engineering journal |
Abbreviated Journal |
Chem Eng J |
|
|
Volume |
222 |
Issue |
|
Pages |
411-418 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Diesel soot emissions deteriorate the appearance of architectural building materials by soot fouling. This soot deposition devalue the aesthetic value of the building. A solution to counteract this problem is applying titanium dioxide on building materials. TiO2 can provide air-purifying and self-cleaning properties due to its photocatalytic activity. In literature, photocatalytic soot oxidation is observed on glass or silicon substrates. However, degradation of soot by photocatalysis was not yet investigated on cementitious samples (mortar, concrete) although it is one of the most frequently used building materials. In this study, photocatalytic soot oxidation by means of TiO2 coated cementitious samples is addressed. The soot removal capacity of four types of TiO2 layers, coated on mortar samples, is evaluated by means of two detection methods. The first method is based on colorimetric measurements, while the second method uses digital image processing to calculate the area of soot coverage. The experimental data revealed that cementitious materials coated with commercially available TiO2 exhibited self-cleaning properties as it was found that all coated samples were able to remove soot. The P25 coating gave the best soot degradation performance, while the Eoxolit product showed the slowest soot degradation rate. In addition, gas chromatography measurements in a closed chamber experiment with P25 confirmed that complete mineralization of about 60% of the soot was obtained within 24 hours since CO2 was the sole observed oxidation product. Due to its realistic approach, this study proves that photocatalytic soot removal on TiO2 coated cementitious surfaces is possible in practice, which is an important step towards the practical application of self-cleaning building materials. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000319528900046 |
Publication Date |
2013-03-05 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1385-8947; 1873-3212 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
6.216 |
Times cited |
43 |
Open Access |
|
|
|
Notes |
; This work was supported by a PhD grant (M. Smits) from the University of Antwerp, a PhD grant (T. Tytgat) funded by the Institute of Innovation by Science and Technology in Flanders (IWT) and the exchange program Tournesol (Project T2012.05) financed by the Flemish government. ; |
Approved |
Most recent IF: 6.216; 2013 IF: 4.058 |
|
|
Call Number |
UA @ admin @ c:irua:106519 |
Serial |
5979 |
|
Permanent link to this record |
|
|
|
|
Author |
De Baere, K.; Verstraelen, H.; Rigo, P.; Van Passel, S.; Lenaerts, S.; Potters, G. |
|
|
Title |
Study on alternative approaches to corrosion protection of ballast tanks using an economic model |
Type |
A1 Journal article |
|
Year |
2013 |
Publication |
Marine structures |
Abbreviated Journal |
Mar Struct |
|
|
Volume |
32 |
Issue |
|
Pages |
1-17 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
One of the most relevant problems in ship construction and maintenance nowadays is corrosion in ballast tanks of modern merchant vessels. On the one hand, there is a general consensus that the economic lifespan of such a vessel depends, to a large degree, upon the corrosion state of its ballast tanks, while on the other hand these ballast tanks, located between the outer hull and the cargo tanks, makes routine inspection and maintenance a difficult task. Today, ship's ballast tanks are usually constructed in steel and protected with an epoxy coating backed up by sacrificial zinc anodes. Such a construction has been applied without significant alterations for many years. The objective of this economic study is to compare this construction method with some potential alternatives. The considered alternatives are: (1) an increase in structural scantlings, eliminating the necessity to replace corroded at a cost of real cargo carrying capacity of the ship, (2) application of the novel and more durable TSCF25 coating (3), the use of corrosion resistant steel in ship construction and (4) a standard PSPC15 coating combined with lifetime lasting aluminum sacrificial anodes. A cost model was used to evaluate these alternative options together with sensitivity analysis. It is concluded that the durable coating and the use of lifetime lasting aluminum anodes are bound to improve the actual basic tank concept. Corrosion resistant steel becomes attractive when the steel price becomes competitive. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000319643500001 |
Publication Date |
2013-03-27 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0951-8339 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.052 |
Times cited |
15 |
Open Access |
|
|
|
Notes |
; ; |
Approved |
Most recent IF: 2.052; 2013 IF: 1.242 |
|
|
Call Number |
UA @ admin @ c:irua:109346 |
Serial |
6253 |
|
Permanent link to this record |
|
|
|
|
Author |
De Baere, K.; Verstraelen, H.; Rigo, P.; Van Passel, S.; Lenaerts, S.; Potters, G. |
|
|
Title |
Reducing the cost of ballast tank corrosion : an economic modeling approach |
Type |
A1 Journal article |
|
Year |
2013 |
Publication |
Marine structures |
Abbreviated Journal |
Mar Struct |
|
|
Volume |
32 |
Issue |
|
Pages |
136-152 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
One of the most relevant problems in ship construction and maintenance nowadays concerns the corrosion in the double hull space ballast tanks of modern merchant vessels. On the one hand, there is a general consensus that the economic life span of such a vessel depends primarily upon the corrosion state of its ballast tanks, while on the other hand, the position of these tanks, squeezed between the outer hull and the loading tanks, makes routine inspection and maintenance almost impossible. Today, ship's ballast tanks are usually constructed in grade A steel and protected with a standard epoxy coating, backed up with sacrificial zinc anodes. Such a construction has been applied without significant alterations for many years. However, the objective of this economic study is to compare this construction method with some feasible alternatives. The considered alternatives are: (1) an increase of the scantlings, eliminating the necessity to replace corroded steel but diminishing the cargo carrying capacity of the ship, (2) application of the novel and more durable TSCF25 coating (3), the use of corrosion resistant steel in ship construction or (4) a standard PSPC15 coating combined with lifetime lasting aluminum sacrificial anodes. After running each alternative through a cost model including an extensive sensitivity analysis, it is concluded that the durable coating and the use of lifetime lasting aluminum anodes are bound to improve the actual basic tank concept. Corrosion resistant steel becomes attractive depending upon the evolution of the international steel market. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000319643500007 |
Publication Date |
2013-05-01 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0951-8339 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.052 |
Times cited |
9 |
Open Access |
|
|
|
Notes |
; ; |
Approved |
Most recent IF: 2.052; 2013 IF: 1.242 |
|
|
Call Number |
UA @ admin @ c:irua:109347 |
Serial |
6240 |
|
Permanent link to this record |