Home << 1 2 3 4 5 6 7 8 9 10 11 12 >>
List View
 | 
Citations
 | 
Details
   web
Records
Author Schryvers, D.
Title Advanced electron microscopy characterisation of important precipitation and ordering phenomena in shape memory systems Type A1 Journal article
Year 2015 Publication Shape memory and superelasticity Abbreviated Journal
Volume (up) 1 Issue 1 Pages 78-84
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract The present paper discusses some important aspects of precipitation and ordering in alloy systems that show a martensitic transformation and can or are used as shape memory or superelastic metallic systems. The precipitates are investigated by a variety of conventional and advanced electron microscopy techniques, including atomic resolution, 3D slice-and-view, energy loss spectroscopy etc. Depending on the system, such secondary phases can decrease the probability of a displacive transformation by changing the phase stability in the system, such as in the case of NiAl or NiTiPd, or can mechanically hinder the passage of the transformation interface, as in NiTiNb. On the other hand, properly controlling the nucleation and growth of some precipitates can strongly improve the properties of some types of materials, as is the case for the well-known Ni4Ti3 precipitates.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000432420400008 Publication Date 2015-04-20
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 2199-384X;2199-3858; ISBN Additional Links UA library record; WoS full record
Impact Factor Times cited Open Access
Notes Fwo Approved Most recent IF: NA
Call Number c:irua:127684 Serial 69
Permanent link to this record
 
 
Author Tian, H.; Schryvers, D.; Mohanchandra, K.P.; Carman, G.P.; van Humbeeck, J.
Title Fabrication and characterization of functionally graded Ni-Ti multilayer thin films Type A1 Journal article
Year 2009 Publication Functional materials letters Abbreviated Journal Funct Mater Lett
Volume (up) 2 Issue 2 Pages 61-66
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract A functionally graded multilayer NiTi thin film was deposited on a SiO2/Si substrate by d.c. sputtering using a ramped heated NiTi alloy target. The stand-alone films were crystallized at 500°C in vacuum better than 10-7 Torr. Transmission electron microscopy micrographs taken along the film cross section show two distinct regions, thin and thick, with weak R and B2 phases, respectively. The film compositions along the thickness were measured and quantified using the standard-less EELSMODEL method. The film deposited during the initial thermal ramp (thin regions) displays an average of 54 at.% Ni while the film deposited at a more elevated target temperature (thick regions) shows about 51 at.% Ni.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000271077000003 Publication Date 2009-07-22
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1793-6047;1793-7213; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 1.234 Times cited 9 Open Access
Notes Fwo Approved Most recent IF: 1.234; 2009 IF: 2.561
Call Number UA @ lucian @ c:irua:77655 Serial 1165
Permanent link to this record
 
 
Author Schryvers, D.
Title Martensitic and bainitic transformations in Ni-Al alloys Type A1 Journal article
Year 1994 Publication Journal de physique: 4 Abbreviated Journal
Volume (up) C2 Issue Pages 225-234
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Les Ulis Editor
Language Wos Publication Date 0000-00-00
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1155-4339 ISBN Additional Links UA library record
Impact Factor Times cited Open Access
Notes Approved
Call Number UA @ lucian @ c:irua:10014 Serial 1946
Permanent link to this record
 
 
Author Malard, B.; Pilch, J.; Sittner, P.; Gartnerova, V.; Delville, R.; Schryvers, D.; Curfs, C.
Title Microstructure and functional property changes in thin Ni-Ti wires heat teated by electric current: high energy X-ray and TEM investigations Type A1 Journal article
Year 2009 Publication Functional materials letters Abbreviated Journal Funct Mater Lett
Volume (up) 2 Issue 2 Pages 45-54
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract High energy synchrotron X-ray diffraction, transmission electron microscopy and mechanical testing were employed to investigate the evolution of microstructure, texture and functional superelastic properties of 0.1 mm thin as drawn NiTi wires subjected to a nonconventional heat treatment by controlled electric current (FTMT-EC method). As drawn NiTi wires were prestrained in tension and exposed to a sequence of short DC power pulses in the millisecond range. The annealing time in the FTMT-EC processing can be very short but the temperature and force could be very high compared to the conventional heat treatment of SMAs. It is shown that the heavily strained, partially amorphous microstructure of the as drawn NiTi wire transforms under the effect of the DC pulse and tensile stress into a wide range of annealed nanosized microstructures depending on the pulse time. The functional superelastic properties and microstructures of the FTMT-EC treated NiTi wire are comparable to those observed in straight annealed wires.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000271077000001 Publication Date 2009-07-22
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1793-6047;1793-7213; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 1.234 Times cited 21 Open Access
Notes Multimat Approved Most recent IF: 1.234; 2009 IF: 2.561
Call Number UA @ lucian @ c:irua:77656 Serial 2052
Permanent link to this record
 
 
Author Schryvers, D.; Toth, L.; Ma, Y.; Tanner, L.E.
Title Nucleation and growth of the Ni5Al3 in NiAl austenite and martensite Type A1 Journal article
Year 1994 Publication Journal de physique: 4 Abbreviated Journal
Volume (up) C2 Issue Pages 299-304
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Les Ulis Editor
Language Wos Publication Date 0000-00-00
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1155-4339 ISBN Additional Links UA library record
Impact Factor Times cited Open Access
Notes Approved no
Call Number UA @ lucian @ c:irua:10015 Serial 2388
Permanent link to this record
 
 
Author Yao, X.; Cao, S.; Zhang, X.P.; Schryvers, D.
Title Microstructural Characterization and Transformation Behavior of Porous Ni50.8Ti49.2 Type P1 Proceeding
Year 2015 Publication Materials Today: Proceedings Abbreviated Journal
Volume (up) 2 Issue 2 Pages S833-S836
Keywords P1 Proceeding; Electron microscopy for materials research (EMAT)
Abstract Porous Ni50.8Ti49.2 bulk material was prepared by powder metallurgy sintering. Solid solution and aging treatments were applied to improve the phase homogeneity and phase transformation behavior. Scanning and transmission electron microscopy, aided by energy dispersive X-ray analysis, were used to study the microstructure and chemical phase content of the alloys. In-situ cooling was carried out to observe the phase transformation behavior. As-received material contains dispersed Ni2Ti4O particles while Ni4Ti3 precipitates appear after aging. Close to pore edges, the latter have a preferential orientation due to the induced stress fields in the matrix.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000371032100081 Publication Date 2015-11-05
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 2214-7853 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor Times cited Open Access
Notes The author gratefully acknowledges the Chinese Scholarship Council (CSC) for providing a scholarship and the Key Project of the Natural Science Foundation of Guangdong Province under grant No. S2013020012805. Approved Most recent IF: NA
Call Number c:irua:129980 Serial 3989
Permanent link to this record
 
 
Author Idrissi, H.; Bollinger, C.; Boioli, F.; Schryvers, D.; Cordier, P.
Title Low-temperature plasticity of olivine revisited with in situ TEM nanomechanical testing Type A1 Journal article
Year 2016 Publication Science Advances Abbreviated Journal
Volume (up) 2 Issue 2 Pages e1501671-e1501671
Keywords A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Abstract The rheology of the lithospheric mantle is fundamental to understanding how mantle convection couples with plate tectonics. However, olivine rheology at lithospheric conditions is still poorly understood because experiments are difficult in this temperature range where rocks and mineral become very brittle. We combine techniques of quantitative in situ tensile testing in a transmission electron microscope and numerical modeling of dislocation dynamics to constrain the low-temperature rheology of olivine. We find that the intrinsic ductility of olivine at low temperature is significantly lower than previously reported values, which were obtained under strain-hardened conditions. Using this method, we can anchor rheological laws determined at higher temperature and can provide a better constraint on intermediate temperatures relevant for the lithosphere. More generally, we demonstrate the possibility of characterizing the mechanical properties of specimens, which can be available in the form of submillimeter-sized particles only.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000379620200043 Publication Date 2016-03-12
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 2375-2548 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor Times cited 32 Open Access
Notes Approved Most recent IF: NA
Call Number UA @ lucian @ c:irua:134983 Serial 4202
Permanent link to this record
 
 
Author Yao, X.; Amin-Ahmadi, B.; Li, Y.; Cao, S.; Ma, X.; Zhang, X.-P.; Schryvers, D.
Title Optimization of Automated Crystal Orientation Mapping in a TEM for Ni4Ti3 Precipitation in All-Round SMA Type A1 Journal article
Year 2016 Publication Shape memory and superelasticity Abbreviated Journal Shap Mem Superelasticity
Volume (up) 2 Issue 2 Pages 286-297
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Automated crystal orientation and phase mapping in TEM are applied to the quantification of Ni4Ti3 precipitates in Ni–Ti shape memory alloys which will be used for the implantation of artificial sphincters operating using the all-round shape memory effect. This paper focuses on the optimization process of the technique to obtain best values for all major parameters in the acquisition of electron diffraction patterns as well as template generation. With the obtained settings, vast statistical data on nano- and microstructures essential to the operation of these shape memory devices become available.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000408743700001 Publication Date 2016-11-07
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 2199-384X ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor Times cited 2 Open Access
Notes X. Yao gratefully acknowledges the Chinese Scholarship Council (CSC) for providing a PhD scholarship. Research support was also provided by the Key Project of the Natural Science Foundation of Guangdong Province (S2013020012805) and the Natural Science Foundation of China under Grant No. 51401081. Approved Most recent IF: NA
Call Number EMAT @ emat @ c:irua:138600 Serial 4324
Permanent link to this record
 
 
Author Poulain, R.; Lumbeeck, G.; Hunka, J.; Proost, J.; Savolainen, H.; Idrissi, H.; Schryvers, D.; Gauquelin, N.; Klein, A.
Title Electronic and chemical properties of nickel oxide thin films and the intrinsic defects compensation mechanism Type A1 Journal article
Year 2022 Publication ACS applied electronic materials Abbreviated Journal
Volume (up) 4 Issue 6 Pages 2718-2728
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Although largely studied, contradictory results on nickel oxide (NiO) properties can be found in the literature. We herein propose a comprehensive study that aims at leveling contradictions related to NiO materials with a focus on its conductivity, surface properties, and the intrinsic charge defects compensation mechanism with regards to the conditions preparation. The experiments were performed by in situ photo-electron spectroscopy, electron energy loss spectroscopy, and optical as well as electrical measurements on polycrystalline NiO thin films prepared under various preparation conditions by reactive sputtering. The results show that surface and bulk properties were strongly related to the deposition temperature with in particular the observation of Fermi level pinning, high work function, and unstable oxygen-rich grain boundaries for the thin films produced at room temperature but not at high temperature (>200 degrees C). Finally, this study provides substantial information about surface and bulk NiO properties enabling to unveil the origin of the high electrical conductivity of room temperature NiO thin films and also for supporting a general electronic charge compensation mechanism of intrinsic defects according to the deposition temperature.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000819431200001 Publication Date 2022-06-07
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 2637-6113 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor Times cited Open Access Not_Open_Access
Notes Approved Most recent IF: NA
Call Number UA @ admin @ c:irua:189555 Serial 7081
Permanent link to this record
 
 
Author Seo, J.W.; Schryvers, D.
Title Defect structures in CuZr martensite, studies by CTEM and HRTEM Type A1 Journal article
Year 1997 Publication Journal de physique: 4 Abbreviated Journal J Phys Iv
Volume (up) C5 Issue Pages 149-154
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Les Ulis Editor
Language Wos 000072520300024 Publication Date 2007-07-11
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1155-4339; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor Times cited 1 Open Access
Notes Approved Most recent IF: NA
Call Number UA @ lucian @ c:irua:21351 Serial 623
Permanent link to this record
 
 
Author Schryvers, D.
Title Electron microscopy studies of martensite microstructures Type A1 Journal article
Year 1997 Publication Journal de physique: 4 Abbreviated Journal J Phys Iv
Volume (up) C5 Issue Pages 109-118
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Les Ulis Editor
Language Wos 000072520300018 Publication Date 2007-07-11
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1155-4339; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor Times cited 2 Open Access
Notes Approved Most recent IF: NA
Call Number UA @ lucian @ c:irua:21348 Serial 968
Permanent link to this record
 
 
Author Schryvers, D.; Yandouzi, M.; Holland-Moritz, D.; Toth, L.
Title HRTEM study of austenite and martensite in splat-cooled and nanoscale thin film Ni-Al Type A1 Journal article
Year 1997 Publication Journal de physique: 4 Abbreviated Journal J Phys Iv
Volume (up) C5 Issue Pages 203-208
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Les Ulis Editor
Language Wos 000072520300033 Publication Date 2007-07-11
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1155-4339; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor Times cited 2 Open Access
Notes Approved Most recent IF: NA
Call Number UA @ lucian @ c:irua:21350 Serial 1517
Permanent link to this record
 
 
Author Schryvers, D.
Title Martensitic and related transformations in Ni-Al alloys Type A1 Journal article
Year 1995 Publication Journal de physique: 4 T2 – IIIrd European Symposium on Martensitic Transformations (ESOMAT 94), SEP 14-16, 1994, BARCELONA, SPAIN Abbreviated Journal IIIrd European Symposium on Martensitic Transformations (ESOMAT 94), SEP 14-16, 1994, BARCELONA, SPA
Volume (up) 5 Issue C2 Pages 225-234
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract The present paper gives a review of results of recent studies investigating the fundamentals of the martensitic and related phase transformations in Ni-Al. For the former case, the emphasis will be on the microstructure of martensite plates. The latter include the metastable Ni2Al omega-like and stable Ni5Al3 bainitic phases. These phases will be discussed in view of their atomic structure, nucleation, growth and effect on the martensitic transformation. A separate chapter will deal with precursor effects.
Address
Corporate Author Thesis
Publisher Place of Publication Les Ulis Editor
Language Wos A1995QX40700036 Publication Date 2007-07-12
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1155-4339; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor Times cited 21 Open Access
Notes Approved no
Call Number UA @ lucian @ c:irua:104437 Serial 1947
Permanent link to this record
 
 
Author Schryvers, D.; Toth, L.; Ma, Y.; Tanner, L.
Title Nucleation and growth of the Ni5Al3 phase in Ni-Al austenite and martensite Type A1 Journal article
Year 1995 Publication Journal de physique: 4 T2 – IIIrd European Symposium on Martensitic Transformations (ESOMAT 94), SEP 14-16, 1994, BARCELONA, SPAIN Abbreviated Journal IIIrd European Symposium on Martensitic Transformations (ESOMAT 94), SEP 14-16, 1994, BARCELONA, SPA
Volume (up) 5 Issue C2 Pages 299-304
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract The nucleation and growth mechanisms of Ni5Al3 precipitates and microtwinned plates in B2 austenite and 2M (3R) martensite phases are described on the basis of conventional and high resolution electron microscopy. In the Ni62.5Al37.5 B2 austenite matrix short annealings at 550 degrees C introduce three-pointed star shaped precipitates consisting of twin related parts of different variants of the Ni5Al3 structure. Longer annealings result in plates growing separately from these wings and developing microtwinning in order to accommodate stress built-up at the interfaces with the surrounding matrix. Annealing of Ni65Al35 2M martensite plates induces simple reordering into the Ni5Al3 phase, increasing the fct c/a ratio by about 1%. As a result stracking faults are introduced in the smallest twin variants.
Address
Corporate Author Thesis
Publisher Place of Publication Les Ulis Editor
Language Wos A1995QX40700047 Publication Date 2007-07-12
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1155-4339; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor Times cited 3 Open Access
Notes Approved no
Call Number UA @ lucian @ c:irua:104438 Serial 2387
Permanent link to this record
 
 
Author Schryvers, D.
Title SAED and HREM results suggest a NiTi B19' based superstructure for CuZr martensite Type A1 Journal article
Year 1995 Publication Journal de physique: colloques, suppléments Abbreviated Journal
Volume (up) 5 Issue 8 Pages 1047-1052
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Les Ulis Editor
Language Wos A1995TX21300085 Publication Date 2014-07-16
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1155-4339; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor Times cited 2 Open Access
Notes Approved MATERIALS SCIENCE, MULTIDISCIPLINARY 96/271 Q2 #
Call Number UA @ lucian @ c:irua:13168 Serial 2939
Permanent link to this record
 
 
Author Schryvers, D.; Toth, L.; van Humbeeck, J.; Beyer, J.
Title Ni2Al versus Ni5Al3 ordering in Ni65Al35 austenite and martensite Type A1 Journal article
Year 1995 Publication Journal de physique: colloques, suppléments Abbreviated Journal
Volume (up) 5 Issue 8 Pages 1029-1034
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Les Ulis Editor
Language Wos A1995TX21300082 Publication Date 2014-07-16
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1155-4339; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor Times cited 12 Open Access
Notes Approved PHYSICS, APPLIED 47/145 Q2 #
Call Number UA @ lucian @ c:irua:13167 Serial 3548
Permanent link to this record
 
 
Author Pourbabak, S.; Orekhov, A.; Samaee, V.; Verlinden, B.; Van Humbeeck, J.; Schryvers, D.
Title In-Situ TEM Stress Induced Martensitic Transformation in Ni50.8Ti49.2 Microwires Type A1 Journal article
Year 2019 Publication Shape memory and superelasticity Abbreviated Journal Shap. Mem. Superelasticity
Volume (up) 5 Issue 2 Pages 154-162
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract In-situ transmission electron microscopy tensile straining is used to study the stress induced martensitic transformation in Ni50.8Ti49.2. Two microwire samples with different heat treatment are investigated from which one single crystal and three polycrystalline TEM specimens, the latter with micro- and nano-size grains, have been produced. The measured Young’s modulus for all TEM specimens is around 70 GPa, considerably higher than the averaged 55 GPa of the original microwire sample. The height of the superelastic stress plateau shows an inverse relationship with the specimen thickness for the polycrystalline specimens. Martensite starts nucleating within the elastic region of the stress–strain curve and on the edges of the specimens while also grain boundaries act as nucleation sites in the polycrystalline specimens. When a martensite plate reaches a grain boundary in the polycrystalline specimen, it initiates the transformation in the neighboring grain at the other side of the grain boundary. In later stages martensite plates coalesce at higher loads in the stress plateau. In highly strained specimens, residual martensite remains after release.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000472940200002 Publication Date 2019-05-20
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 2199-384X ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor Times cited Open Access Not_Open_Access
Notes Saeid Pourbabak likes to thank the Flemish Science Foundation FWO for financial support under Project G.0366.15N. This work was also made possible through the AUHA13009 Grant “TopSPIN for TEM nanostatistics” of the Flemish HERCULES foundation. Approved Most recent IF: NA
Call Number EMAT @ emat @UA @ admin @ c:irua:159989 Serial 5177
Permanent link to this record
 
 
Author Schryvers, D.; Holland-Moritz, D.
Title Austenite and martensite microstructures in splat-cooled Ni-Al Type A1 Journal article
Year 1998 Publication Intermetallics Abbreviated Journal Intermetallics
Volume (up) 6 Issue Pages 427-436
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Chicago, Ill. Editor
Language Wos 000074235500010 Publication Date 2002-07-25
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0966-9795; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 3.14 Times cited 13 Open Access
Notes Approved Most recent IF: 3.14; 1998 IF: 1.785
Call Number UA @ lucian @ c:irua:48365 Serial 209
Permanent link to this record
 
 
Author Colla, M.-S.; Amin-Ahmadi, B.; Idrissi, H.; Malet, L.; Godet, S.; Raskin, J.-P.; Schryvers, D.; Pardoen, T.
Title Dislocation-mediated relaxation in nanograined columnar ​palladium films revealed by on-chip time-resolved HRTEM testing Type A1 Journal article
Year 2015 Publication Nature communications Abbreviated Journal Nat Commun
Volume (up) 6 Issue 6 Pages 5922
Keywords A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Abstract The high-rate sensitivity of nanostructured metallic materials demonstrated in the recent literature is related to the predominance of thermally activated deformation mechanisms favoured by a large density of internal interfaces. Here we report time-resolved high-resolution electron transmission microscopy creep tests on thin nanograined films using on-chip nanomechanical testing. Tests are performed on ​palladium, which exhibited unexpectedly large creep rates at room temperature. Despite the small 30-nm grain size, relaxation is found to be mediated by dislocation mechanisms. The dislocations interact with the growth nanotwins present in the grains, leading to a loss of coherency of twin boundaries. The density of stored dislocations first increases with applied deformation, and then decreases with time to drive additional deformation while no grain boundary mechanism is observed. This fast relaxation constitutes a key issue in the development of various micro- and nanotechnologies such as ​palladium membranes for hydrogen applications.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000348742300002 Publication Date 2015-01-05
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 2041-1723; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 12.124 Times cited 34 Open Access
Notes Iap7/21; Fwo G012012n Approved Most recent IF: 12.124; 2015 IF: 11.470
Call Number c:irua:122045 Serial 731
Permanent link to this record
 
 
Author Samajdar, I.; Ratchev, P.; Verlinden, B.; Schryvers, D.
Title Recrystallization and grain growth in a B2 iron aluminide alloy Type A1 Journal article
Year 1998 Publication Intermetallics Abbreviated Journal Intermetallics
Volume (up) 6 Issue Pages 419-425
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Chicago, Ill. Editor
Language Wos 000074235500009 Publication Date 2002-07-25
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0966-9795; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 3.14 Times cited 17 Open Access
Notes Approved Most recent IF: 3.14; 1998 IF: 1.785
Call Number UA @ lucian @ c:irua:48366 Serial 2846
Permanent link to this record
 
 
Author Van Aelst, J.; Philippaerts, A.; Bartholomeeusen, E.; Fayad, E.; Thibault-Starzyk, F.; Lu, J.; Schryvers, D.; Ooms, R.; Verboekend, D.; Jacobs, P.; Sels, B.
Title Towards biolubricant compatible vegetable oils by pore mouth hydrogenation with shape-selective Pt/ZSM-5 catalysts Type A1 Journal article
Year 2016 Publication Catalysis science & technology Abbreviated Journal Catal Sci Technol
Volume (up) 6 Issue 6 Pages 2820-2828
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Pt/ZSM-5 catalysts with various crystal sizes were prepared via competitive ion-exchange, followed by a slow activation procedure. Even when using very large ZSM-5 crystals, highly dispersed Pt nano-clusters were contained within the zeolite crystal's voids, as ascertained by 2D pressure-jump IR spectroscopy of adsorbed CO and focussed ion-beam transmission electron microscopy. The shape-selective properties of the Pt/ZSM-5 catalysts were evaluated in the partial hydrogenation of soybean oil. Unique hydrogenation selectivities were observed, as the fatty acids located at the central position of the triacylglycerol (TAG) molecules were preferentially hydrogenated. The resulting oil has therefore high levels of intermediately melting TAGs, which are compatible with biolubricants due to their improved oxidative stability and still appropriate low-temperature fluidity. The TAG distribution in the partially hydrogenated soybean oil samples was independent from the zeolite crystal size, while the hydrogenation activity linearly increases with the crystal's external surface area. This trend was confirmed with a Pt loaded mesoporous ZSM-5 zeolite, obtained via a mild alkaline treatment. These observations imply and confirm a genuine pore mouth catalysis mechanism, in which only one fatty acid chain of the TAG is able to enter the micropores of ZSM-5, where the double bonds are hydrogenated by the crystal encapsulated Pt-clusters.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000374790200031 Publication Date 2016-03-31
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 2044-4753 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 5.773 Times cited 5 Open Access
Notes The research was funded through a PhD grant to J. V. A. of the Agency for Innovation by Science and Technology in Flanders (IWT). A. P. and D. V. acknowledge the F. W. O.-Vlaanderen (Research Foundation Flanders) for a post-doctoral fellowship. E. B. was kindly funded by an F. W. O.-Vlaanderen project. This work was performed in the framework of an Associated International Laboratory between FWO and CNRS. Approved Most recent IF: 5.773
Call Number EMAT @ emat @ c:irua:138981 Serial 4335
Permanent link to this record
 
 
Author Tian, H.; Schryvers, D.; Liu, D.; Jiang, Q.; van Humbeeck, J.
Title Stability of Ni in nitinol oxide surfaces Type A1 Journal article
Year 2011 Publication Acta biomaterialia Abbreviated Journal Acta Biomater
Volume (up) 7 Issue 2 Pages 892-899
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract The stability of Ni in titanium oxide surface layers on nitinol wires known to release certain amounts of Ni was investigated by first principles density functional theory and transmission electron microscopy. The oxides were identified as a combination of TiO and TiO2 depending on the thickness of the layer. The calculations indicate that free Ni atoms can exist in TiO at ambient temperature while Ni particles form in TiO2, which was confirmed by the transmission electron microscopy observations. The results are discussed with respect to surface stability and Ni release due to free Ni atoms and Ni particles.
Address
Corporate Author Thesis
Publisher Place of Publication S.l. Editor
Language Wos 000286707700047 Publication Date 2010-09-17
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1742-7061; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 6.319 Times cited 39 Open Access
Notes Fwo Approved Most recent IF: 6.319; 2011 IF: 4.865
Call Number UA @ lucian @ c:irua:85998 Serial 3128
Permanent link to this record
 
 
Author Schouteden, K.; Amin-Ahmadi, B.; Li, Z.; Muzychenko, D.; Schryvers, D.; Van Haesendonck, C.
Title Electronically decoupled stacking fault tetrahedra embedded in Au(111) films Type A1 Journal article
Year 2016 Publication Nature communications Abbreviated Journal Nat Commun
Volume (up) 7 Issue 7 Pages 14001
Keywords A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Abstract Stacking faults are known as defective structures in crystalline materials that typically lower the structural quality of the material. Here, we show that a particular type of defects, i.e., stacking fault tetrahedra (SFTs), exhibits quantized, particle-in-a-box electronic behaviour, revealing a potential synthetic route to decoupled nanoparticles in metal films. We report on the electronic properties of SFTs that exist in Au(111) films, as evidenced by scanning tunnelling microscopy and confirmed by transmission electron microscopy. We find that the SFTs reveal a remarkable decoupling from their metal surroundings, leading to pronounced energy level quantization effects within the SFTs. The electronic behaviour of the SFTs can be described well by the particle-in-a-box model. Our findings demonstrate that controlled preparation of SFTs may offer an alternative way to achieve well decoupled nanoparticles of high crystalline quality in metal thin films without the need of thin insulating layers.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000390367700001 Publication Date 2016-12-23
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 2041-1723 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 12.124 Times cited 7 Open Access
Notes The research in Leuven has been supported by the Research Foundation – Flanders (FWO, Belgium), and by the Flemish Concerted Research Action program (BOF KU Leuven, Project No. GOA/14/007). Z.L. acknowledges the support from the China Scholarship Council (No. 2011624021) and from Internal Funds KU Leuven. K.S. acknowledges additional support from the FWO. The research in Moscow has been supported by grants of the Russian Foundation for Basic Research (RFBR). Approved Most recent IF: 12.124
Call Number EMAT @ emat @ c:irua:138983 Serial 4336
Permanent link to this record
 
 
Author Marteleur, M.; Idrissi, H.; Amin-Ahmadi, B.; Prima, F.; Schryvers, D.; Jacques, P.J.
Title On the nucleation mechanism of {112} < 111 > mechanical twins in as-quenched beta metastable Ti-12 wt.% Mo alloy Type A1 Journal article
Year 2019 Publication Materialia Abbreviated Journal
Volume (up) 7 Issue Pages Unsp 100418
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Recently developed beta-metastable Ti grades take advantage of the simultaneous activation of TRIP and TWIP effects for enhancing their work hardening rate. However, the role of each plasticity mechanism on the macroscopic mechanical response is still unclear. In this work, the nucleation mechanism of the first activated plasticity mechanism, namely {112} < 111 > twinning, was investigated. Firstly, post-mortem TEM analysis showed that twins nucleate on pre-existing microstructural defects such as thermal jogs with the zonal dislocation mechanism. The precipitation of the omega phase on twin boundaries has been observed, as well as the emission of numerous dislocations from super-jogs present in these twin boundaries. It is also shown that {112} < 111 > twins act as effective dislocation sources for the subsequent plasticity mechanisms such as beta -> alpha '' martensitic transformation and {332} < 111 > twinning. Secondly, in situ TEM tensile testing of the investigated Ti grade highlighted the primary role of the initial defect configuration present in the microstructure. It is shown that twins cannot nucleate without the presence of specific defects allowing the triggering of the dislocation decomposition needed for the twinning mechanism highlighted in investigated bulk samples.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000537131000052 Publication Date 2019-07-31
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 2589-1529 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor Times cited Open Access
Notes Approved no
Call Number UA @ admin @ c:irua:170326 Serial 6875
Permanent link to this record
 
 
Author Tirry, W.; Schryvers, D.
Title Linking a completely three-dimensional nanostrain to a structural transformation eigenstrain Type A1 Journal article
Year 2009 Publication Nature materials Abbreviated Journal Nat Mater
Volume (up) 8 Issue 9 Pages 752-757
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract NiTi is one of the most popular shape-memory alloys, a phenomenon resulting from a martensitic transformation. Commercial NiTi-based alloys are often thermally treated to contain Ni4Ti3 precipitates. The presence of these precipitates can introduce an extra transformation step related to the so-called R-phase. It is believed that the strain field surrounding the precipitates, caused by the matrixprecipitate lattice mismatch, lies at the origin of this intermediate transformation step. Atomic-resolution transmission electron microscopy in combination with geometrical phase analysis is used to measure the elastic strain field surrounding these precipitates. By combining measurements from two different crystallographic directions, the three-dimensional strain matrix is determined from two-dimensional measurements. Comparison of the measured strain matrix to the eigenstrain of the R-phase shows that both are very similar and that the introduction of the R-phase might indeed compensate the elastic strain introduced by the precipitate.
Address
Corporate Author Thesis
Publisher Place of Publication London Editor
Language Wos 000269215500022 Publication Date 2009-06-21
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1476-1122;1476-4660; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 39.737 Times cited 53 Open Access
Notes Multimat Approved Most recent IF: 39.737; 2009 IF: 29.504
Call Number UA @ lucian @ c:irua:77657 Serial 1822
Permanent link to this record
 
 
Author Samaee, V.; Gatti, R.; Devincre, B.; Pardoen, T.; Schryvers, D.; Idrissi, H.
Title Dislocation driven nanosample plasticity: new insights from quantitative in-situ TEM tensile testing Type A1 Journal Article
Year 2018 Publication Scientific Reports Abbreviated Journal Sci Rep-Uk
Volume (up) 8 Issue 1 Pages 12012
Keywords A1 Journal Article; Electron Microscopy for Materials Science (EMAT) ;
Abstract Intrinsic dislocation mechanisms in the vicinity of free surfaces of an almost FIB damage-free single crystal Ni sample have been quantitatively investigated owing to a novel sample preparation method combining twin-jet electro-polishing, in-situ TEM heating and FIB. The results reveal that the small-scale plasticity is mainly controlled by the conversion of few tangled dislocations, still present after heating, into stable single arm sources (SASs) as well as by the successive operation of these sources. Strain hardening resulting from the operation of an individual SAS is reported and attributed to the decrease of the length of the source. Moreover, the impact of the shortening of the dislocation source on the intermittent plastic flow, characteristic of SASs, is discussed. These findings provide essential information for the understanding of the regime of ‘dislocation source’ controlled plasticity and the related mechanical size effect.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000460200900001 Publication Date 2018-08-07
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 2045-2322 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 4.259 Times cited 9 Open Access Not_Open_Access
Notes Financial support from the Flemish (FWO) and German Research Foundation (DFG) through the European M-ERA.NET project “FaSS” (Fatigue Simulation near Surfaces) under the grant numbers GA.014.13 N and SCHW855/5-1, respectively, is gratefully acknowledged. V. Samaee also acknowledges the FWO research project G012012N “Understanding nanocrystalline mechanical behaviour from structural investigations”. H. Idrissi is mandated by the Belgian National Fund for Scientific Research (FSR-FNRS). Dr. Ruth Schwaiger is acknowledged for providing the Ni foils used to prepare the in-situ TEM tensile specimens. Approved Most recent IF: 4.259
Call Number EMAT @ emat @c:irua:155772 Serial 5136
Permanent link to this record
 
 
Author Satto, C.; Ledda, A.; Potapov, P.; Janssens, J.F.; Schryvers, D.
Title Phase transformations and precipitation in amorphous Ti50Ni25Cu25 ribbons Type A1 Journal article
Year 2001 Publication Intermetallics Abbreviated Journal Intermetallics
Volume (up) 9 Issue Pages 395-401
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Chicago, Ill. Editor
Language Wos 000168882500005 Publication Date 2002-07-25
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0966-9795; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 3.14 Times cited 16 Open Access
Notes Approved Most recent IF: 3.14; 2001 IF: 1.239
Call Number UA @ lucian @ c:irua:48367 Serial 2590
Permanent link to this record
 
 
Author Idrissi, H.; Ghidelli, M.; Béché, A.; Turner, S.; Gravier, S.; Blandin, J.-J.; Raskin, J.-P.; Schryvers, D.; Pardoen, T.
Title Atomic-scale viscoplasticity mechanisms revealed in high ductility metallic glass films Type A1 Journal article
Year 2019 Publication Scientific reports Abbreviated Journal Sci Rep-Uk
Volume (up) 9 Issue 1 Pages 13426
Keywords A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Abstract The fundamental plasticity mechanisms in thin freestanding Zr65Ni35 metallic glass films are investigated in order to unravel the origin of an outstanding strength/ductility balance. The deformation process is homogenous until fracture with no evidence of catastrophic shear banding. The creep/relaxation behaviour of the films was characterized by on-chip tensile testing, revealing an activation volume in the range 100–200 Å3. Advanced high-resolution transmission electron microscopy imaging and spectroscopy exhibit a very fine glassy nanostructure with well-defined dense Ni-rich clusters embedded in Zr-rich clusters of lower atomic density and a ~2–3 nm characteristic length scale. Nanobeam electron diffraction analysis reveals that the accumulation of plastic deformation at roomtemperature

correlates with monotonously increasing disruption of the local atomic order. These results provide experimental evidences of the dynamics of shear transformation zones activation in metallic glasses. The impact of the nanoscale structural heterogeneities on the mechanical properties including the rate dependent behaviour is discussed, shedding new light on the governing plasticity mechanisms in metallic glasses with initially heterogeneous atomic arrangement.
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos 000486139700008 Publication Date 2019-09-17
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 2045-2322 ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 4.259 Times cited Open Access
Notes H. Idrissi is mandated by the Belgian National Fund for Scientific Research (FSR-FNRS). This work was supported by the FNRS under Grant PDR – T.0178.19. FWO project G093417N (‘Compressed sensing enabling low dose imaging in transmission electron microscopy’) and Hercules fund ‘Direct electron detector for soft matter TEM’ from Flemish Government are acknowledged. Approved Most recent IF: 4.259
Call Number EMAT @ emat @c:irua:162786 Serial 5375
Permanent link to this record
 
 
Author Yandouzi, M.; Toth, L.; Schryvers, D.
Title High resolution transmission electron microscopy study of nanoscale Ni-rich Ni-Al films evaporated onto NaCl and KCl Type A1 Journal article
Year 1998 Publication Nanostructured materials Abbreviated Journal Nanostruct Mater
Volume (up) 10 Issue Pages 99-115
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication New York Editor
Language Wos 000073840600011 Publication Date 2002-07-25
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0965-9773; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor Times cited 2 Open Access
Notes Approved Most recent IF: NA
Call Number UA @ lucian @ c:irua:48370 Serial 1463
Permanent link to this record
 
 
Author Fredrickx, P.; Schryvers, D.
Title La microscopie électronique à transmission (MET) et son utilisation dans l'étude d'inclusions nano-cristallines dans le verre Type A3 Journal article
Year 2002 Publication L'archéométrie au service des monuments et des oeuvres d'art Abbreviated Journal
Volume (up) 10 Issue Pages 131-136
Keywords A3 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Editor
Language Wos Publication Date 0000-00-00
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN ISBN Additional Links UA library record
Impact Factor Times cited Open Access
Notes Approved Most recent IF: NA
Call Number UA @ lucian @ c:irua:48776 Serial 2036
Permanent link to this record