|
“Understanding CeO2-Based Nanostructures through Advanced Electron Microscopy in 2D and 3D”. Zhang Y, Bals S, Van Tendeloo G, Particle and particle systems characterization 36, 1800287 (2019). http://doi.org/10.1002/ppsc.201800287
Abstract: Engineering morphology and size of CeO2-based nanostructures on a (sub)nanometer scale will greatly influence their performance; this is because of their high oxygen storage capacity and unique redox properties, which allow faster switching of the oxidation state between Ce4+ and Ce3+. Although tremendous research has been carried out on the shapecontrolled synthesis of CeO2, the characterization of these nanostructures at the atomic scale remains a major challenge and the origin of debate. The rapid developments of aberration-corrected transmission electron microscopy (AC-TEM) have pushed the resolution below 1 Å, both in TEM and in scanning transmission electron microscopy (STEM) mode. At present, not only morphology and structure, but also composition and electronic structure can be analyzed at an atomic scale, even in 3D. This review summarizes recent significant achievements using TEM/ STEM and associated spectroscopic techniques to study CeO2-based nanostructures and related catalytic phenomena. Recent results have shed light on the understanding of the different mechanisms. The potential and limitations, including future needs of various techniques, are discussed with recommendations to facilitate further developments of new and highly efficient CeO2-based nanostructures.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 4.474
Times cited: 22
DOI: 10.1002/ppsc.201800287
|
|
|
“Thermal recrystallization of short-range ordered WS2 films”. Heyne MH, de Marneffe J-F, Radu I, Neyts EC, De Gendt S, Journal of vacuum science and technology: A: vacuum surfaces and films 36, 05g501 (2018). http://doi.org/10.1116/1.5036654
Abstract: The integration of van der Waals materials in nanoelectronic devices requires the deposition of few-layered MX2 films with excellent quality crystals covering a large area. In recent years, astonishing progress in the monolayer growth of WS2 and MoS2 was demonstrated, but multilayer growth resulted often in separated triangular or hexagonal islands. These polycrystalline films cannot fully employ the specific MX2 properties since they are not connected in-plane to the other domains. To coalesce separated islands, ultrahigh-temperature postdeposition anneals in H2S are applied, which are not compatible with bare silicon substrates. Starting from the deposition of stoichiometric short-ordered films, the present work studies different options for subsequent high-temperature annealing in an inert atmosphere to form crystalline films with large grains from stoichiometric films with small grains. The rapid thermal annealing, performed over a few seconds, is compared to excimer laser annealing in the nanosecond range, which are both able to crystallize the thin WS2. The WS2 recrystallization temperature can be lowered using metallic crystallization promoters (Co and Ni). The best result is obtained using a Co cap, due to the circumvention of Co and S binary phase formation below the eutectic temperature. The recrystallization above a critical temperature is accompanied by sulfur loss and 3D regrowth. These undesired effects can be suppressed by the application of a dielectric capping layer prior to annealing. A SiO2 cap can suppress the sulfur loss successfully during annealing and reveals improved material quality in comparison to noncapped films Published by the AVS.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.374
Times cited: 2
DOI: 10.1116/1.5036654
|
|
|
“Investigation on porosity changes of Lecce stone due to conservation treatments by means of x-ray nano- and improved micro-computed tomography: preliminary results”. Bugani S, Camaiti M, Morselli L, Van de Casteele E, Janssens K, X-ray spectrometry 36, 316 (2007). http://doi.org/10.1002/XRS.976
Keywords: A1 Journal article; Vision lab; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Impact Factor: 1.298
Times cited: 28
DOI: 10.1002/XRS.976
|
|
|
“Analyzing a self-managed CHP system for greenhouse cultivation as a profitable way to reduce CO2-emissions”. Compernolle T, Witters N, Van Passel S, Thewys T, Energy 36, 1940 (2011). http://doi.org/10.1016/J.ENERGY.2010.02.045
Abstract: To counter global warming, a transition to a low-carbon economy is needed. The greenhouse sector can contribute by installing Combined Heat and Power (CHP) systems, known for their excellent energy efficiency. Due to the recent European liberalization of the energy market, glass horticulturists have the opportunity to sell excess electricity to the market and by tailored policy and support measures, regional governments can fill the lack of technical and economic knowledge, causing initial resistance. This research investigates the economic and environmental opportunities using two detailed cases applying a self managed cogeneration system. The Net Present Value is calculated to investigate the economic feasibility. The Primary Energy Saving, the CO2 Emission Reduction indicator and an Emission Balance are applied to quantify the environmental impact. The results demonstrate that a self-managed CHP system is economic viable and that CO2 emissions are reduced. (C) 2010 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology
Impact Factor: 4.52
Times cited: 19
DOI: 10.1016/J.ENERGY.2010.02.045
|
|
|
“Interface cation migration kinetics induced oxygen release heterogeneity in layered lithium cathodes”. Li C-F, Zhao K, Liao X, Hu Z-Y, Zhang L, Zhao Y, Mu S, Li Y, Li Y, Van Tendeloo G, Sun C, Energy Storage Materials 36, 115 (2021). http://doi.org/10.1016/J.ENSM.2020.12.018
Abstract: The irreversible release of the lattice oxygen in layered cathodes is one of the major degradation mechanisms of lithium ion batteries, which accounts for a number of battery failures including the voltage/capacity fade, loss of cation ions and detachment of the primary particles, etc. Oxygen release is generally attributed to the stepwise thermodynamic controlled phase transitions from the layered to spinel and rock salt phases. Here, we report a strong kinetic effect from the mobility of cation ions, whose migration barrier can be significantly modulated by the phase epitaxy at the degrading interface. It ends up with a clear oxygen release heterogeneity and completely different reaction pathways between the thin and thick areas, as well as the interparticle valence boundaries, both of which widely exist in the mainstream cathode design with the secondary agglomerates. This work unveils the origin of the heterogenous oxygen release in the layered cathodes. It also sheds light on the rational design of cathode materials with enhanced oxygen stability by suppressing the cation migration.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
DOI: 10.1016/J.ENSM.2020.12.018
|
|
|
“The adsorption and decomposition of SF6 over defective and hydroxylated MgO surfaces: A DFT study”. Cui Z, Hao Y, Jafarzadeh A, Li S, Bogaerts A, Li L, Surfaces and interfaces 36, 102602 (2023). http://doi.org/10.1016/j.surfin.2022.102602
Abstract: Plasma degradation is one of the most effective methods for the abatement of greenhouse gas sulfur hexafluoride
(SF6). To evaluate the potential of MgO as a catalyst in plasma degradation, we investigate the catalytic properties
of MgO on SF6 adsorption and activation by density functional theory (DFT) where the O-defective and
hydroxylated surfaces are considered as two typical plasma-generated surfaces. Our results show that perfect
MgO (001) and (111) surfaces cannot interact with SF6 and only physical adsorption happens. In case of Odefective
MgO surfaces, the O vacancy is the most stable adsorption site. SF6 undergoes a decomposition to SF5
and F over the O-defective MgO (001) surface and undergoes an elongation of the bottom S-F bond over the Odefective
(111) surface. Besides, SF6 shows a physically adsorption at the stepsite of the MgO (001) surface,
accompanied by small changes in its bond angle and length. Furthermore, SF6 is found to be physically and
chemically adsorbed over 0.5 and 1.0 ML (monolayer) H-covered O-terminated MgO (111) surfaces, respectively.
The SF6 molecule undergoes a self-decomposition on the 1.0 ML hydroxylated surface via a surface bonding
process. This study shows that defective and hydroxylated MgO surfaces have the surface capacities for SF6
activation, which shows that MgO has potential as packing material in SF6 waste treatment in packed-bed
plasmas.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 6.2
DOI: 10.1016/j.surfin.2022.102602
|
|
|
“Occupancy of lattice positions probed by X-ray photoelectron diffraction : a case study of tetradymite topological insulators”. Vladimirova NV, Frolov AS, Sanchez-Barriga J, Clark OJ, Matsui F, Usachov DY, Muntwiler M, Callaert C, Hadermann J, Neudachina VS, Tamm ME, Yashina LV, Surfaces and interfaces 36, 102516 (2023). http://doi.org/10.1016/J.SURFIN.2022.102516
Abstract: Occupancy of different structural positions in a crystal lattice often seems to play a key role in material prop-erties. Several experimental techniques have been developed to uncover this issue, all of them being mostly bulk sensitive. However, many materials including topological insulators (TIs), which are among the most intriguing modern materials, are intended to be used in devices as thin films, for which the sublattice occupancy may differ from the bulk. One of the possible approaches to occupancy analysis is X-ray Photoelectron Diffraction (XPD), a structural method in surface science with chemical sensitivity. We applied this method in a case study of Sb2(Te1-xSex)3 mixed crystals, which belong to prototypical TIs. We used high-angle annular dark field (HAADF) scanning transmission electron microscopy (STEM) as a reference method to verify our analysis. We revealed that the XPD data for vacuum cleaved bulk crystals are in excellent agreement with the reference ones. Also, we demonstrate that the anion occupancy near a naturally formed surface can be rather different from that of the bulk. The present results are relevant for a wide range of compositions where the system remains a topological phase, as we ultimately show by probing the transiently occupied topological surface state above the Fermi level by ultrafast photoemission.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 6.2
DOI: 10.1016/J.SURFIN.2022.102516
|
|
|
“The application of Raman spectrometry to investigate and characterize cement: part I: a review”. Potgieter-Vermaak SS, Potgieter JH, Van Grieken R, Cement and concrete research 36, 656 (2006). http://doi.org/10.1016/J.CEMCONRES.2005.09.008
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
DOI: 10.1016/J.CEMCONRES.2005.09.008
|
|
|
“The application of Raman spectrometry to the investigation of cement: part 2: a micro-Raman study of OPC, slag and fly ash”. Potgieter-Vermaak SS, Potgieter JH, Belleil M, DeWeerdt F, Van Grieken R, Cement and concrete research 36, 663 (2006). http://doi.org/10.1016/J.CEMCONRES.2005.09.010
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
DOI: 10.1016/J.CEMCONRES.2005.09.010
|
|
|
“Bridging global, basin and local-scale water quality modeling towards enhancing water quality management worldwide”. Tang T, Strokal M, van Vliet MTH, Seuntjens P, Burek P, Kroeze C, Langan S, Wada Y, Current Opinion in Environmental Sustainability 36, 39 (2019). http://doi.org/10.1016/J.COSUST.2018.10.004
Abstract: Global water quality (WQ) modeling is an emerging field. In this article, we identify the missing linkages between global and basin/local-scale WQ models, and discuss the possibilities to fill these gaps. We argue that WQ models need stronger linkages across spatial scales. This would help to identify effective scale-specific WQ management options and contribute to future development of global WQ models. Two directions are proposed to improve the linkages: nested multiscale WQ modeling towards enhanced water management, and development of next-generation global WQ models based-on basin/local-scale mechanistic understanding. We highlight the need for better collaboration among WQ modelers and policy-makers in order to deliver responsive water policies and management strategies across scales.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.COSUST.2018.10.004
|
|
|
“Characterisation of aerosol particles in the São Paulo Metropolitan Area”. de Miranda RM, de Fátima Andrade M, Worobiec A, Van Grieken R, Atmospheric environment : an international journal 36, 345 (2002). http://doi.org/10.1016/S1352-2310(01)00363-6
Keywords: A1 Journal article; Laboratory Experimental Medicine and Pediatrics (LEMP); AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
DOI: 10.1016/S1352-2310(01)00363-6
|
|
|
“Characterisation of particulate matter in the Royal Museum of Fine Arts, Antwerp, Belgium”. Gysels K, Deutsch F, Van Grieken R, Atmospheric environment : an international journal 36, 4103 (2002). http://doi.org/10.1016/S1352-2310(02)00229-7
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
DOI: 10.1016/S1352-2310(02)00229-7
|
|
|
“Characterisation of wood combustion particles using electron probe microanalysis”. Osán J, Alföldy B, Török S, Van Grieken R, Atmospheric environment : an international journal 36, 2207 (2002). http://doi.org/10.1016/S1352-2310(02)00153-X
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
DOI: 10.1016/S1352-2310(02)00153-X
|
|
|
“Comprehensive microanalytical study of welding aerosols with x-ray and Raman based methods”. Worobiec A, Stefaniak EA, Kiro S, Oprya M, Bekshaev A, Spolnik Z, Potgieter-Vermaak SS, Ennan A, Van Grieken R, X-ray spectrometry 36, 328 (2007). http://doi.org/10.1002/XRS.979
Keywords: A1 Journal article; Laboratory Experimental Medicine and Pediatrics (LEMP); AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
DOI: 10.1002/XRS.979
|
|
|
“Effects of IR heating on distribution and transport of gaseous air pollutants in urban and mountain churches in Poland”. Bencs L, Spolnik Z, Worobiec A, Samek L, Jutte BAHG, Van Grieken R, Journal of cultural heritage 36, 200 (2019). http://doi.org/10.1016/J.CULHER.2018.09.007
Abstract: The spatial distribution and temporal concentration variation of a set of gaseous air components (e.g., CO2, CO, H2CO, H2O) have been monitored with a multi-channel photoacoustic gas-analyzer in an urban church ( Saint Catherine's, Cracow) and a mountain church ( Saint Michaels Archangel, Szalowa) of Poland, in order to assess the likely effects of air pollution indoors under the influence of provisory electrical infrared (IR) heaters and without heating. Likewise, the ventilation characteristic and the leakage of these buildings with different constructions (i.e., plastered stone and wooden structures) with the assistance of decay curves of SF6 tracer gas was evaluated and compared. The wooden building in Szalowa, due to its more open structure, developed about one order higher ventilation rates (e.g., 0.9-1.3 h(-1)) than the stone church in Cracow (e.g., 0.1 h(-1)). The IR-heating affected only modestly the ventilation rate of the wooden church (e.g., 1.2-1.6 h(-1)), but it increased significantly that of the plastered stone church (e.g., 0.27 h(-1)). The ventilation rates were also assessed with the use of the CO2 curve decay method, and satisfactory agreement was found with those observed by the use of SF6 tracer. The spatial distribution of the studied gaseous pollutants (CO2, H2O) was found to be in some occasions nonhomogeneous in both buildings, due to the active usage of the IR-heating, especially, during a couple of consecutive liturgical services. Besides the pollution events due to ingress of gaseous air pollutants, present at enhanced levels outdoors, increased CO, CO2 and H2CO peaks were observed indoors too, which, in most cases, could be associated with incense burning. (C) 2018 Elsevier Masson SAS. All rights reserved.
Keywords: A1 Journal article; Art; History; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Laboratory Experimental Medicine and Pediatrics (LEMP)
DOI: 10.1016/J.CULHER.2018.09.007
|
|
|
“Quantification of boron in cells for evaluation of drug agents used in boron neutron capture therapy”. Verlinden B, Van Hoecke K, Aerts A, Daems N, Dobney A, Janssens K, Cardinaels T, Journal Of Analytical Atomic Spectrometry 36, 598 (2021). http://doi.org/10.1039/D0JA00456A
Abstract: Boron neutron capture therapy (BNCT) is an extensively studied radiotherapeutic strategy for cancer treatment. BNCT is based on irradiation of malignant tumour cells with neutrons after uptake of a B-10 containing molecule. Alpha particles, locally produced by neutron irradiation kill the cancer cells. Important for ongoing research regarding cellular uptake and cytotoxicity of a large variety of B-10 containing molecules is the accurate determination of boron concentrations in cell cultures. In this work, the sample preparation for quantitative inductively coupled plasma mass spectrometry (ICP-MS) analysis on cell cultures was optimized. By making use of acid digestion combined with UV digestion, low detection limits (0.4 mu g L-1) and full recoveries of boron could be achieved while measurements were free of spectral and non-spectral interferences. Finally, cell-associated boron in the form of 4-borono-l-phenylalanine (l-BPA) in vascular endothelial cell cultures could be determined with ICP-MS as (1.26 +/- 0.10) x 10(9) boron atoms per cell. The developed method can prove its importance for further BNCT research and elemental analysis of cell cultures.
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Impact Factor: 3.379
DOI: 10.1039/D0JA00456A
|
|
|
“Quantification of the impact of macrophytes on oxygen dynamics and nitrogen retention in a vegetated lowland river”. Desmet NJS, van Belleghem S, Seuntjens P, Bouma TJ, Buis K, Meire P, Physics and chemistry of the earth, parts A/B/C 36, 479 (2011). http://doi.org/10.1016/J.PCE.2008.06.002
Abstract: When macrophytes are growing in the river, the vegetation induces substantial changes to the water quality. Some effects are the result of direct interactions, such as photosynthetic activity or nutrient uptake, whereas others may be attributed to indirect effects of the water plants on hydrodynamics and river processes. This research focused on the direct effect of macrophytes on oxygen dynamics and nutrient cycling. Discharge, macrophyte biomass density, basic water quality, dissolved oxygen and nutrient concentrations were in situ monitored throughout the year in a lowland river (Nete catchment, Belgium). In addition, various processes were investigated in more detail in multiple ex situ experiments. The field and aquaria measurement results clearly demonstrated that aquatic plants can exert considerable impact on dissolved oxygen dynamics in a lowland river. When the river was dominated by macrophytes, dissolved oxygen concentrations varied from 5 to 10 mg l−1. Considering nutrient retention, it was shown that the investigated in-stream macrophytes could take up dissolved inorganic nitrogen (DIN) from the water column at rates of View the MathML source. And DIN fluxes towards the vegetation were found to vary from 0.03 to 0.19 g N ha−1 h−1 in spring and summer. Compared to the measured changes in DIN load over the river stretch, it means that about 313% of the DIN retention could be attributed to direct nitrogen uptake from the water by macrophytes. Yet, the role of macrophytes in rivers should not be underrated as aquatic vegetation also exerts considerable indirect effects that may have a greater impact than the direct fixation of nutrients into the plant biomass.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.PCE.2008.06.002
|
|
|
“Single-particle characterization of urban aerosol particles collected in three Korean cities using low-Z electron probe x-ray microanalysis”. Ro C-U, Kim H, Oh K-Y, Yea SK, Lee CB, Jang M, Van Grieken R, Environmental science and technology 36, 4770 (2002). http://doi.org/10.1021/ES025697Y
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
DOI: 10.1021/ES025697Y
|
|
|
“Comment on 'Integral cross sections for electron impact excitation of electronic states of N2'”. Cenian A, Chernukho A, Bogaerts A, Gijbels R, Journal of physics: B : atomic and molecular physics 35, 5163 (2002). http://doi.org/10.1088/0953-4075/35/24/401
Abstract: Based on the existing experimental data and their statistical errors, it is not possible to make a sound recommendation of the cross-section set of Campbell et al (J. Phys. B: At. Mol. Opt. Phys. 34 (2001) 1185). We comment on this paper.
Keywords: Editorial; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.792
Times cited: 2
DOI: 10.1088/0953-4075/35/24/401
|
|
|
“Critical influence of alumina content on the low temperature degradation of 2-3 mol% yttria-stabilized TZP for dental restorations”. Zhang F, Vanmeensel K, Inokoshi M, Batuk M, Hadermann J, Van Meerbeek B, Naert I, Vleugels J, Journal of the European Ceramic Society 35, 741 (2015). http://doi.org/10.1016/j.jeurceramsoc.2014.09.018
Abstract: The influence of 0.25, 2 and 5 wt.% alumina addition on the mechanical properties and low temperature degradation (LTD) of 3, 2.5 and 2 mol% yttria-stabilized TZP ceramics was investigated. The amount of alumina addition was observed to have a crucial impact on the degradation of Y-TZP ceramics. Independent on the yttria stabilizer content, 0.25 wt.% alumina had a higher degradation retarding effect to Y-TZP ceramics than 2 and 5 wt.% of alumina addition, which had a comparable effect. The apparent activation energy for the degradation process was increased by adding alumina, but it was the same for 0.255 wt.% alumina doped 3Y-TZP ceramics. For Y-TZPs containing a small amount of alumina addition, only the segregated Al3+ at the grain boundaries of the zirconia grains was effective to retard the degradation of Y-TZPs. The secondary phase Al2O3 grains increased the degradation kinetics, which might be attributed to the residual stresses.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.411
Times cited: 37
DOI: 10.1016/j.jeurceramsoc.2014.09.018
|
|
|
“Electron-electron scattering induced capture in GaAs quantum wells”. Kálna K, Mo×ko M, Peeters FM, Lithuanian journal of physics 35, 435 (1995)
Keywords: A3 Journal article; Condensed Matter Theory (CMT)
|
|
|
“Flat GaN epitaxial layers grown on Si(111) by metalorganic vapor phase epitaxy using step-graded AlGaN intermediate layers”. Cheng K, Leys M, Degroote S, van Daele B, Boeykens S, Derluyn J, Germain M, Van Tendeloo G, Engelen J, Borghs G, Journal of electronic materials 35, 592 (2006). http://doi.org/10.1007/s11664-006-0105-1
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.579
Times cited: 102
DOI: 10.1007/s11664-006-0105-1
|
|
|
“Glow discharge modelling: from basic understanding towards applications”. Bogaerts A, Chen Z, Gijbels R, Surface and interface analysis 35, 593 (2003). http://doi.org/10.1002/sia.1578
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.132
Times cited: 14
DOI: 10.1002/sia.1578
|
|
|
“How to optimize the experimental design of quantitative atomic resolution TEM experiments?”.Van Aert S, den Dekker AJ, van Dyck D, Micron 35, 425 (2004). http://doi.org/10.1016/j.micron.2004.01.007
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT); Vision lab
Impact Factor: 1.98
Times cited: 14
DOI: 10.1016/j.micron.2004.01.007
|
|
|
“HREM investigation of martensite precursor effects and stacking sequences in Ni-Mn-Ti alloys”. Schryvers D, Lahjouji DE, Slootmaekers B, Potapov PL, Scripta metallurgica et materialia 35, 1235 (1996). http://doi.org/10.1016/1359-6462(96)00271-0
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.224
Times cited: 2
DOI: 10.1016/1359-6462(96)00271-0
|
|
|
“Modeling and experimental study of trichloroethylene abatement with a negative direct current corona discharge”. Vandenbroucke AM, Aerts R, Van Gaens W, De Geyter N, Leys C, Morent R, Bogaerts A, Plasma chemistry and plasma processing 35, 217 (2015). http://doi.org/10.1007/s11090-014-9584-7
Abstract: In this work, we study the abatement of dilute trichloroethylene (TCE) in air with a negative direct current corona discharge. A numerical model is used to theoretically investigate the underlying plasma chemistry for the removal of TCE, and a reaction pathway for the abatement of TCE is proposed. The Cl atom, mainly produced by dissociation of COCl, is one of the controlling species in the TCE destruction chemistry and contributes to the production of chlorine containing by-products. The effect of humidity on the removal efficiency is studied and a good agreement is found between experiments and the model for both dry (5 % relative humidity (RH)) and humid air (50 % RH). An increase of the relative humidity from 5 % to 50 % has a negative effect on the removal efficiency, decreasing by ±15 % in humid air. The main loss reactions for TCE are with ClO·, O· and CHCl2. Finally, the by-products and energy cost of TCE abatement are discussed.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 2.355
Times cited: 9
DOI: 10.1007/s11090-014-9584-7
|
|
|
“Molecular orientation and conductivity in highly oriented poly(p-phenylene vinylene)”. Briers J, Eevers W, Cos P, Geise HJ, Mertens R, Nagels P, Zhang XB, Van Tendeloo G, Herrebout W, van der Veken B, Polymer 35, 4569 (1994). http://doi.org/10.1016/0032-3861(94)90804-4
Keywords: A1 Journal article; Molecular Spectroscopy (MolSpec); Electron microscopy for materials research (EMAT)
Impact Factor: 3.562
Times cited: 16
DOI: 10.1016/0032-3861(94)90804-4
|
|
|
“Superior reliability of junctionless pFinFETs by reduced oxide electric field”. Toledano-Luque M, Matagne P, Sibaja-Hernandez A, Chiarella T, Ragnarsson L-A, Sorée B, Cho M, Mocuta A, Thean A, IEEE electron device letters 35, 1179 (2014). http://doi.org/10.1109/LED.2014.2361769
Abstract: Superior reliability of junctionless (JL) compared with inversion-mode field-effect transistors (FETs) is experimentally demonstrated on bulk FinFET wafers. The reduced negative bias temperature instability (NBTI) of JL pFETs outperforms the previously reported best NBTI reliability data obtained with Si channel devices and guarantees 10-year lifetime at typical operating voltages and high temperature. This behavior is understood through the reduced oxide electric field and lessened interaction between charge carriers and oxide traps during device operation. These findings encourage the investigation of JL devices with alternative channels as a promising alternative for 7-nm technology nodes meeting reliability targets.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.048
Times cited: 13
DOI: 10.1109/LED.2014.2361769
|
|
|
“Understanding the Effect of Iodide Ions on the Morphology of Gold Nanorods”. Amini MN, Altantzis T, Lobato I, Grzelczak M, Sánchez-Iglesias A, Van Aert S, Liz-Marzán LM, Partoens B, Bals S, Neyts EC, Particle and particle systems characterization 35, 1800051 (2018). http://doi.org/10.1002/ppsc.201800051
Abstract: The presence of iodide ions during the growth of gold nanorods strongly affects the shape of the final products, which is proposed to be due to selective iodide adsorption on certain crystallographic facets. Therefore, a detailed structural and morphological characterization of the starting rods is crucial toward understanding this effect. Electron tomography is used to determine the crystallographic indices of the lateral facets of gold nanorods, as well as those present at the tips. Based on this information, density functional theory calculations are used to determine the surface and interface energies of the observed facets and provide insight into the relationship between the amount of iodide ions in the growth solution and the final morphology of anisotropic gold nanoparticles.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Condensed Matter Theory (CMT); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 4.474
Times cited: 6
DOI: 10.1002/ppsc.201800051
|
|
|
“Comparison of synchrotron X-ray microanalysis with electron and proton microscopy for individual particle analysis”. Janssens KH, Adams FC, van Langevelde F, Vis RD, Jones KW, Rivers M, Sutton S, Advances in X-ray analysis 35, 1265 (1992)
Keywords: A3 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
|
|