|   | 
Details
   web
Records
Author Afanasov, I.M.; Morozov, V.A.; Kepman, A.V.; Ionov, S.G.; Seleznev, A.N.; Van Tendeloo, G.; Audeev, V.V.
Title Preparation, electrical and thermal properties of new exfoliated graphite-based composites Type A1 Journal article
Year 2009 Publication Carbon Abbreviated Journal Carbon
Volume 47 Issue 1 Pages 263-270
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Exfoliated graphite samples (EG) with different bulk densities were prepared by the exfoliation of expandable graphite under a thermal shock regime. As a conductive filler, EG has been incorporated successfully into the coal tar pitch matrix by mechanical mixing. The conducting behavior of the composite was interpreted based on the percolation theory. The percolation threshold of the EG/pitch conducting composites at room temperature was as low as 1.5 wt% and did not depend on the bulk density of the EG used. By means of thermogravimetry the improvement of thermal stability of the composites in comparison with pure pitches was detected. The phenomenon was ascribed to heat shielding effect of the EG particles evidenced by matrix-assisted laser desorption/ionization mass spectrometry.
Address
Corporate Author Thesis
Publisher Place of Publication Oxford Editor
Language Wos 000262143500032 Publication Date 2008-10-14
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0008-6223; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 6.337 Times cited 42 Open Access
Notes Iap-Vi Approved Most recent IF: 6.337; 2009 IF: 4.504
Call Number UA @ lucian @ c:irua:75767 Serial 2701
Permanent link to this record
 

 
Author Felten, A.; Ghijsen, J.; Pireaux, J.-J.; Whelan, C.M.; Liang, D.; Van Tendeloo, G.; Bittencourt, C.
Title Photoemission study of CF4 rf-plasma treated multi-wall carbon nanotubes Type A1 Journal article
Year 2008 Publication Carbon Abbreviated Journal Carbon
Volume 46 Issue 10 Pages 1271-1275
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Multi-wall carbon nanotubes (MWCNTs) were exposed to a CF4 rf-plasma. X-ray photoelectron spectroscopy analysis shows that the treatment effectively grafts fluorine atoms onto the MWCNTs. The fluorine atomic concentration and the nature of the CF bond (semi-ionic or covalent) can be tuned by varying the exposure time. Ultraviolet photoelectron spectroscopy analysis confirms that the valence electronic states are altered by the grafting of fluorine atoms. Characterization with high-resolution transmission electron microscopy reveals that while the plasma treatment does not induce significant etching impact on the CNT-surface, it does increase the number of active sites for gold cluster formation.
Address
Corporate Author Thesis
Publisher Place of Publication Oxford Editor
Language Wos 000258987500001 Publication Date 2008-05-16
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0008-6223; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 6.337 Times cited 21 Open Access
Notes Approved Most recent IF: 6.337; 2008 IF: 4.373
Call Number UA @ lucian @ c:irua:76481 Serial 2612
Permanent link to this record
 

 
Author Felten, A.; Bittencourt, C.; Colomer, J.-F.; Van Tendeloo, G.; Pireaux, J.-J.
Title Nucleation of metal clusters on plasma treated multi wall carbon nanotubes Type A1 Journal article
Year 2007 Publication Carbon Abbreviated Journal Carbon
Volume 45 Issue 1 Pages 110-116
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Oxford Editor
Language Wos 000243583300017 Publication Date 2006-09-27
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0008-6223; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 6.337 Times cited 40 Open Access
Notes Approved Most recent IF: 6.337; 2007 IF: 4.260
Call Number UA @ lucian @ c:irua:63033 Serial 2389
Permanent link to this record
 

 
Author Li, Y.; Zhang, X.B.; Tao, X.Y.; Xu, J.M.; Chen, F.; Shen, L.H.; Yang, X.F.; Liu, F.; Van Tendeloo, G.; Geise, H.J.
Title Single phase MgMoO4 as catalyst for the synthesis of bundled multi-wall carbon nanotubes by CVD Type L1 Letter to the editor
Year 2005 Publication Carbon Abbreviated Journal Carbon
Volume 43 Issue 6 Pages 1325-1328
Keywords L1 Letter to the editor; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Oxford Editor
Language Wos 000228676400026 Publication Date 2005-03-11
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0008-6223; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 6.337 Times cited 23 Open Access
Notes Iap V-1 Approved Most recent IF: 6.337; 2005 IF: 3.419
Call Number UA @ lucian @ c:irua:59055 Serial 3026
Permanent link to this record
 

 
Author Pierard, N.; Fonseca, A.; Colomer, J.-F.; Bossuot, C.; Benoit, J.-M.; Van Tendeloo, G.; Pirard, J.-P.; Nagy, J.B.
Title Ball milling effect on the structure of single-wall carbon nanotubes Type A1 Journal article
Year 2004 Publication Carbon Abbreviated Journal Carbon
Volume 42 Issue 8/9 Pages 1691-1697
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Oxford Editor
Language Wos 000221948000035 Publication Date 2004-04-09
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0008-6223; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 6.337 Times cited 133 Open Access
Notes Pai/Iuap P5/01 Approved Most recent IF: 6.337; 2004 IF: 3.331
Call Number UA @ lucian @ c:irua:54866 Serial 213
Permanent link to this record
 

 
Author Gorlé, C.; van Beeck, J.; Rambaud, P.; Van Tendeloo, G.
Title CFD modelling of small particle dispersion: the influence of the turbulence kinetic energy in the atmospheric boundary layer Type A1 Journal article
Year 2009 Publication Atmospheric environment : an international journal Abbreviated Journal Atmos Environ
Volume 43 Issue 3 Pages 673-681
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract When considering the modelling of small particle dispersion in the lower part of the Atmospheric Boundary Layer (ABL) using Reynolds Averaged Navier Stokes simulations, the particle paths depend on the velocity profile and on the turbulence kinetic energy, from which the fluctuating velocity components are derived to predict turbulent dispersion. It is therefore important to correctly reproduce the ABL, both for the velocity profile and the turbulence kinetic energy profile. For RANS simulations with the standard kå model, Richards and Hoxey (1993. Appropriate boundary conditions for computational wind engineering models using the kå turbulence model. Journal of Wind Engineering and Industrial Aerodynamics 4647, 145153.) proposed a set of boundary conditions which result in horizontally homogeneous profiles. The drawback of this method is that it assumes a constant profile of turbulence kinetic energy, which is not always consistent with field or wind tunnel measurements. Therefore, a method was developed which allows the modelling of a horizontally homogeneous turbulence kinetic energy profile that is varying with height. By comparing simulations performed with the proposed method to simulations performed with the boundary conditions described by Richards and Hoxey (1993. Appropriate boundary conditions for computational wind engineering models using the kå turbulence model. Journal of Wind Engineering and Industrial Aerodynamics 4647, 145153.), the influence of the turbulence kinetic energy on the dispersion of small particles over flat terrain is quantified.
Address
Corporate Author Thesis
Publisher Place of Publication Oxford Editor
Language Wos 000262737900023 Publication Date 2008-10-16
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1352-2310; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 3.629 Times cited 79 Open Access
Notes Iwt Approved Most recent IF: 3.629; 2009 IF: 3.139
Call Number UA @ lucian @ c:irua:76016 Serial 306
Permanent link to this record
 

 
Author Verbruggen, S.W.; Keulemans, M.; Filippousi, M.; Flahaut, D.; Van Tendeloo, G.; Lacombe, S.; Martens, J.A.; Lenaerts, S.
Title Plasmonic goldsilver alloy on TiO2 photocatalysts with tunable visible light activity Type A1 Journal article
Year 2014 Publication Applied catalysis : B : environmental Abbreviated Journal Appl Catal B-Environ
Volume 156 Issue Pages 116-121
Keywords A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Sustainable Energy, Air and Water Technology (DuEL)
Abstract Adaptation of the photoresponse of anatase TiO2 to match the solar spectrum is an important scientific challenge. Modification of TiO2 with noble metal nanoparticles displaying surface plasmon resonance effects is one of the promising approaches. Surface plasmon resonance typically depends on chemical composition, size, shape and spatial organization of the metal nanoparticles in contact with TiO2. AuxAg(1 − x) alloy nanoparticles display strong composition-dependent surface plasmon resonance in the visible light region of the spectrum. In this work, a general strategy is presented to prepare plasmonic TiO2-based photocatalysts with a visible light response that can be accurately tuned over a broad range of the spectrum. The application as self-cleaning material toward the degradation of stearic acid is demonstrated for a plasmonic TiO2 photocatalyst displaying visible light photoactivity at the intensity maximum of solar light around 490 nm.
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos 000336013200014 Publication Date 2014-03-22
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0926-3373; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 9.446 Times cited 84 Open Access
Notes Flanders(FWO); Methusalem Approved Most recent IF: 9.446; 2014 IF: 7.435
Call Number UA @ lucian @ c:irua:115552 Serial 2646
Permanent link to this record
 

 
Author Beyers, E.; Biermans, E.; Ribbens, S.; de Witte, K.; Mertens, M.; Meynen, V.; Bals, S.; Van Tendeloo, G.; Vansant, E.F.; Cool, P.
Title Combined TiO2/SiO2 mesoporous photocatalysts with location and phase controllable TiO2 nanoparticles Type A1 Journal article
Year 2009 Publication Applied catalysis : B : environmental Abbreviated Journal Appl Catal B-Environ
Volume 88 Issue 3/4 Pages 515-524
Keywords A1 Journal article; Electron microscopy for materials research (EMAT); Laboratory of adsorption and catalysis (LADCA)
Abstract Combined TiO2/SiO2 mesoporous materials were prepared by deposition of TiO2 nanoparticles synthesised via the acid-catalysed solgel method. In the first synthesis step a titania solution is prepared, by dissolving titaniumtetraisopropoxide in nitric acid. The influences of the initial titaniumtetraisopropoxide concentration and the temperature of dissolving on the final structural properties were investigated. In the second step of the synthesis, the titania nanoparticles were deposited on a silica support. Here, the influence of the temperature during deposition was studied. The depositions were carried out on two different mesoporous silica supports, SBA-15 and MCF, leading to substantial differences in the catalytic and structural properties. The samples were analysed with N2-sorption, X-ray diffraction (XRD), electron probe microanalysis (EPMA) and transmission electron microscopy (TEM) to obtain structural information, determining the amount of titania, the crystal phase and the location of the titania particles on the mesoporous material (inside or outside the mesoporous channels). The structural differences of the support strongly determine the location of the nanoparticles and the subsequent photocatalytic activity towards the degradation of rhodamine 6G in aqueous solution under UV irradiation.
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos 000266513400032 Publication Date 2008-10-29
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0926-3373; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 9.446 Times cited 69 Open Access
Notes Goa-Bof; Fwo Approved Most recent IF: 9.446; 2009 IF: 5.252
Call Number UA @ lucian @ c:irua:77150 Serial 403
Permanent link to this record
 

 
Author de Witte, K.; Meynen, V.; Mertens, M.; Lebedev, O.I.; Van Tendeloo, G.; Sepúlveda-Escribano, A.; Rodríguez-Reinoso, F.; Vansant, E.F.; Cool, P.
Title Multi-step loading of titania on mesoporous silica: influence of the morphology and the porosity on the catalytic degradation of aqueous pollutants and VOC's Type A1 Journal article
Year 2008 Publication Applied catalysis : B : environmental Abbreviated Journal Appl Catal B-Environ
Volume 84 Issue 1/2 Pages 125-132
Keywords A1 Journal article; Electron microscopy for materials research (EMAT); Laboratory of adsorption and catalysis (LADCA)
Abstract Titania nanoparticles have been deposited on inert porous silica supports with high specific surface area. These materials have potential applications in paint and textile industry as the titania particles selectively deposited on the inner surface of the silica supports act as a photocatalyst. The inert external surface is necessary to avoid photodegradation of the textile material or the paint components. The photocatalytic activity of the catalysts has been evaluated with two catalytic setups. One setup in aqueous phase, for the degradation of dyes such as rhodamine-6G, is commonly used. The second setup is a continuous flow gaseous phase setup which was used for the mineralization of ethanol as a representative volatile organic compound (VOC). The influence of the porosity and the morphology of the silica supports on the photocatalytic activity are discussed.
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos 000260728300017 Publication Date 2008-04-08
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0926-3373; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 9.446 Times cited 24 Open Access
Notes Iwt 30916; Fwo Approved Most recent IF: 9.446; 2008 IF: 4.853
Call Number UA @ lucian @ c:irua:68279 Serial 2213
Permanent link to this record
 

 
Author Van Aelst, J.; Philippaerts, A.; Turner, S.; Van Tendeloo, G.; Jacobs, P.; Sels, B.
Title Heterogeneous conjugation of vegetable oil with alkaline treated highly dispersed Ru/USY catalysts Type A1 Journal article
Year 2016 Publication Applied catalysis : A : general Abbreviated Journal Appl Catal A-Gen
Volume 526 Issue 526 Pages 172-182
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Heterogeneous metal catalysts enable the direct conjugation of linoleic acid tails in vegetable oil to their conjugated linoleic acid (CIA) isomers. CIA-enriched oils are useful as renewable feedstock for the chemical industry and as nutraceutical. Up to now, a solvent-free process for conjugated oils without significant formation of undesired hydrogenation products was not existing. This work shows the design of Ru/USY catalysts able to directly conjugate highly unsaturated vegetable oils such as safflower oil in absence of solvent and hydrogen. Key is fast molecular transport of the bulky reagent and reactive product triglycerides in the zeolite crystal. A two-step zeolite post-synthetic treatment (with NH4OH and acetate salt) was applied to create the necessary mesoporosity. More open zeolite structures allow for a faster conjugation reaction, while securing a fast removal of the reactive conjugated triglycerides, otherwise rapidly deactivating through fouling and pore blockage by polymers. The best Ru/USY catalyst in this contribution is capable of producing exceptionally high yields of conjugated oils, containing up to almost 30 wt% conjugated fatty acid tails in safflower oil, at an initial production rate of 328 g(CLA) mL(-1) h(-1) per gram metal catalyst. (C) 2016 Elsevier B.V. All rights reserved.
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos 000384865600021 Publication Date 2016-09-03
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0926-860x ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 4.339 Times cited 1 Open Access
Notes Approved Most recent IF: 4.339
Call Number UA @ lucian @ c:irua:137242 Serial 4383
Permanent link to this record
 

 
Author Geukens, I.; Vermoortele, F.; Meledina, M.; Turner, S.; Van Tendeloo, G.; De Vos, D.E.
Title Ag nanoparticles on mixed Al2O3-Ga2O3 supports as catalysts for the N-alkylation of amines with alcohols Type A1 Journal article
Year 2014 Publication Applied catalysis : A : general Abbreviated Journal Appl Catal A-Gen
Volume 469 Issue Pages 373-379
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract The combination of AgNO3 with NaH results in Ag nanoparticles that can selectively perform alcohol aminations under mild reaction conditions (110 °C). NaH not only serves as a reducing agent for the Ag salt, but also activates the alcohol for dehydrogenation to the corresponding ketone/aldehyde. The stability of the particles can be improved by immobilizing them onto mixed Al2O3Ga2O3 supports; the combination of Ga and Al provides materials with stronger Lewis acidic sites compared to pure alumina or gallium oxide supports. This leads to catalysts with enhanced activities, without the necessity of adding external Lewis acids. Detailed TEM characterization also reveals a close interaction between the Ag NPs and the gallium oxide phase. The obtained catalysts are recyclable and show activity for the alcohol amination using a variety of aliphatic and aromatic amines under mild conditions.
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos 000329266500045 Publication Date 2013-10-10
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0926-860X; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 4.339 Times cited 24 Open Access
Notes Approved Most recent IF: 4.339; 2014 IF: 3.942
Call Number UA @ lucian @ c:irua:111095 Serial 83
Permanent link to this record
 

 
Author Lorenz, H.; Zhao, Q.; Turner, S.; Lebedev, O.I.; Van Tendeloo, G.; Kloetzer, B.; Rameshan, C.; Pfaller, K.
Title Origin of different deactivation of Pd/SnO2 and Pd/GeO2 catalysts in methanol dehydrogenation and reforming: a comparative study Type A1 Journal article
Year 2010 Publication Applied catalysis : A : general Abbreviated Journal Appl Catal A-Gen
Volume 381 Issue 1/2 Pages 242-252
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Pd particles supported on SnO2 and GeO2 have been structurally investigated by X-ray diffraction, (High-Resolution) transmission and scanning electron microscopy after different reductive treatments to monitor the eventual formation of bimetallic phases and catalytically tested in methanol dehydrogenation/ reforming. For both oxides this included a thin film sample with well-defined Pd particles and a powder catalyst prepared by incipient wetness impregnation. The hexagonal and the tetragonal polymorph were studied for powder GeO2. Pd2Ge formation was observed on all GeO2-supported catalysts, strongly depending on the specific sample used. Reduction of the thin film at 573K resulted in full transformation into the bimetallic state. The partial solubility of hexagonal GeO2 in water and its thermal structural instability yielded Pd2Ge formation at 473 K, at the cost of a structurally inhomogeneous support and Ge metal formation at higher reduction temperatures. Pd on tetragonal GeO2 entered a state of strong metalsupport interaction after reduction at 573673 K, resulting in coalescing Pd2Ge particles on a sintered and re-crystallized support, apparently partially covering the bimetallic particles and decreasing the catalytic activity. Pd2Ge on amorphous thin film and hexagonal GeO2 converted methanol primarily via dehydrogenation to CO and H2. At 573 K, formation of Pd2Sn and also PdSn occurred on the Pd/SnO2 thin film. Pd3Sn2 (and to some extent Pd2Sn) were predominantly obtained on the respective powder catalyst. Strong deactivation with increasing reduction temperature was observed, likely not based on the classical strong metalsupport interaction effect, but rather on a combination of missing active structural ensembles on Sn-enriched bimetallic phases and the formation of metallic -Sn. Correlations to Pd and its bimetallics supported on ZnO, Ga2O3 and In2O3 were also discussed.
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos 000279100700029 Publication Date 2010-04-26
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0926-860X; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 4.339 Times cited 14 Open Access
Notes Esteem 026019 Approved Most recent IF: 4.339; 2010 IF: 3.384
Call Number UA @ lucian @ c:irua:83927 Serial 2522
Permanent link to this record
 

 
Author Zhao, Q.; Lorenz, H.; Turner, S.; Lebedev, O.I.; Van Tendeloo, G.; Rameshan, C.; Klötzer, B.; Konzett, J.; Penner, S.
Title Catalytic characterization of pure SnO2 and GeO2 in methanol steam reforming Type A1 Journal article
Year 2010 Publication Applied catalysis : A : general Abbreviated Journal Appl Catal A-Gen
Volume 375 Issue 2 Pages 188-195
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Structural changes of a variety of different SnO, SnO2 and GeO2 catalysts upon reduction in hydrogen were correlated with associated catalytic changes in methanol steam reforming. Studied systems include SnO, SnO2 and GeO2 thin film model catalysts prepared by vapour phase deposition and growth on polycrystalline NaCl surfaces and, for comparison, the corresponding pure oxide powder catalysts. Reduction of both the SnO2 thin film and powder at around 673 K in 1 bar hydrogen leads to a substantial reduction of the bulk structure and yields a mixture of SnO2 and metallic β-Sn. On the powder catalyst this transformation is fully reversible upon oxidation in 1 bar O2 at 673 K. Strongly reduced thin films, however, can only be re-transformed to SnO2 if the reduction temperature did not exceed 573 K. For GeO2, the situation is more complex due to its polymorphism. Whereas the tetragonal phase is structurally stable during reduction, oxidation or catalytic reaction, a small part of the hexagonal phase is always transformed into the tetragonal at 673 K independent of the gas phase used. SnO2 is highly active and CO2 selective in methanol steam reforming, but the initial high activity drops considerably upon reduction between 373 and 573 K and almost complete catalyst deactivation is observed after reduction at 673 K, which is associated with the parallel formation of β-Sn. In close correlation to the structural results, the catalytic activity and selectivity can be restored upon an oxidative catalyst regeneration at 673 K. Tetragonal GeO2 exhibits only a small activity and no pronounced selectivity to either CO or CO2, at least after reduction. In its fully oxidized state release of surface/lattice oxygen results in a non-catalytic formation of CO2 by oxidation of CO originating from catalytic dehydrogenation.
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos 000275580600002 Publication Date 2010-01-15
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0926-860X; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 4.339 Times cited 20 Open Access
Notes Esteem 026019 Approved Most recent IF: 4.339; 2010 IF: 3.384
Call Number UA @ lucian @ c:irua:81741 Serial 292
Permanent link to this record
 

 
Author Lorenz, H.; Turner, S.; Lebedev, O.I.; Van Tendeloo, G.; Klötzer, B.; Rameshan, C.; Pfaller, K.; Penner, S.
Title Pd-In2O3 interaction due to reduction in hydrogen: consequences for methanol steam reforming Type A1 Journal article
Year 2010 Publication Applied catalysis : A : general Abbreviated Journal Appl Catal A-Gen
Volume 374 Issue 1/2 Pages 180-188
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Two different Pd/In2O3 samples including a thin film model catalyst with well-defined Pd particles grown on NaCl(0 0 1) supports and a powder catalyst prepared by an impregnation technique are examined by electron microscopy, X-ray diffraction and catalytic measurements in methanol steam reforming in order to correlate the formation of different oxide-supported bimetallic PdIn phases with catalytic activity and selectivity. A PdIn shell around the Pd particles is observed on the thin film catalyst after embedding the Pd particles in In2O3 at 300 K, likely because alloying to PdIn and oxidation to In2O3 are competing processes. Increased PdIn bimetallic formation is observed up to 573 K reduction temperature until at 623 K the film stability limit in hydrogen is reached. Oxidative treatments at 573 K lead to decomposition of PdIn and to the formation of an In2O3 shell covering the Pd particles, which irreversibly changes the activity and selectivity pattern to clean In2O3. PdIn and Pd2In3 phases are obtained on the powder catalyst after reduction at 573 K and 673 K, respectively. Only CO2-selective methanol steam reforming is observed in the reduction temperature range between 473 K and 573 K. After reduction at 673 K encapsulation of the bimetallic particles by crystalline In2O3 suppresses CO2 formation and only activity and selectivity of clean In2O3 are measured.
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos 000274869900023 Publication Date 2009-12-18
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0926-860X; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 4.339 Times cited 55 Open Access
Notes Esteem 026019 Approved Most recent IF: 4.339; 2010 IF: 3.384
Call Number UA @ lucian @ c:irua:81801 Serial 3553
Permanent link to this record
 

 
Author Viart, N.; Sayed Hassan, R.; Ulhaq-Bouillet, C.; Meny, C.; Panissod, P.; Loison, J.L.; Versini, G.; Huber, F.; Pourroy, G.; Verbeeck, J.; Van Tendeloo, G.
Title Oxidation processes at the metal/oxide interface in CoFe2/CoFe2O4 bilayers deposited by pulsed laser deposition Type A1 Journal article
Year 2006 Publication Acta materialia Abbreviated Journal Acta Mater
Volume 54 Issue 1 Pages 191-196
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract CoFe2/CoFe2O4 bilayers were made by pulsed laser ablation of a CoFe2 target on Si(I 0 0) substrates. The metallic layer was deposited first, in vacuum. The oxide was then deposited in an oxidizing O-2:N-2 (20:80) atmosphere. Two different procedures were used for the introduction of the oxidizing atmosphere in the deposition chamber: the laser ablation of the target was either stopped (discontinuous deposition process) or maintained (continuous deposition process) during the 20 min necessary for the establishment of the desired O-2:N-2 pressure. In both cases, the different electronegativities of Fe and Co cause an important modification of the Fe/Co ratio at the metal/oxide interface, with a depletion of Fe in the metal region and of Co in the oxide region. In the continuous procedure, the combination of the kinetic energy given by the ablation process to the Fe and Co adatoms with the one they get from their different affinity towards oxidation allows the formation of a low roughness metal/oxide interface with a high (111) preferred orientation of the CoFe2O4 layer, an induced re-crystallisation of the metal layer underneath and an unusual antiferromagnetic metal/oxide magnetic coupling. (c) 2005 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
Address
Corporate Author Thesis
Publisher Place of Publication Oxford Editor
Language Wos 000233784500021 Publication Date 2005-10-15
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 1359-6454; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 5.301 Times cited 5 Open Access
Notes Approved Most recent IF: 5.301; 2006 IF: 3.549
Call Number UA @ lucian @ c:irua:56043UA @ admin @ c:irua:56043 Serial 2540
Permanent link to this record
 

 
Author Van Tendeloo, G.; Krekels, T.
Title HREM of ceramic high Tc superconductors Type A1 Journal article
Year 1996 Publication Journal of the European Ceramic Society Abbreviated Journal J Eur Ceram Soc
Volume 16 Issue Pages 367-378
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Barking Editor
Language Wos A1996UC80200005 Publication Date 2002-07-25
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0955-2219; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 2.947 Times cited 1 Open Access
Notes Approved no
Call Number UA @ lucian @ c:irua:16861 Serial 1507
Permanent link to this record
 

 
Author Frangis, N.; Van Tendeloo, G.; van Landuyt, J.; Muret, P.; Nguyen, T.T.A.
Title Structural characterisation of erbium silicide thin films of an Si(111) substrate Type A1 Journal article
Year 1996 Publication Journal of alloys and compounds Abbreviated Journal J Alloy Compd
Volume 234 Issue 2 Pages 244-250
Keywords A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Abstract ErSi2-x films (x = 0.1-0.3) grown by co-evaporation at different deposition ratios have been characterised by transmission electron microscopy, electron diffraction and high resolution electron microscopy. A very good epitaxial growth relation with the Si substrate was deduced for a1 samples and observed phases. Different defect modulated structures are formed; they can be described as structural variants (orthorhombic or rhombohedral) of the basic structure. The modulated phases are related to deviations from stoichiometry similar to crystallographic shear structures. The ErSi1.9 material contains Si precipitates, illustrating the preference for the ErSi1.7 composition to be maintained.
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos A1996TX65100020 Publication Date 2002-07-26
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0925-8388; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 2.999 Times cited 14 Open Access
Notes Approved
Call Number UA @ lucian @ c:irua:15451 Serial 3213
Permanent link to this record
 

 
Author Cziraki, A.; Fogarassy, F.; Van Tendeloo, G.; Lamparter, P.; Tegze, M.; Bakonyi, I.
Title Electron microscopy and X-ray diffraction studies of rapidly quenched Zr-Ni an Hf-Ni ribbons with about 90 at.% Ni Type A1 Journal article
Year 1994 Publication Journal of alloys and compounds Abbreviated Journal J Alloy Compd
Volume 210 Issue Pages 135-141
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos A1994PA71300025 Publication Date 2003-06-21
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0925-8388; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 2.999 Times cited 26 Open Access
Notes Approved no
Call Number UA @ lucian @ c:irua:10039 Serial 950
Permanent link to this record
 

 
Author Van Tendeloo, G.; Krekels, T.; Milat, O.; Amelinckx, S.
Title Structural effects of element substitution on superconducting properties in 1-2-3 YBCO: an electron microscopy study Type A1 Journal article
Year 1993 Publication Journal of alloys and compounds Abbreviated Journal J Alloy Compd
Volume 195 Issue Pages 307-314
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos A1993LC49200075 Publication Date 2003-06-21
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0925-8388; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 2.999 Times cited 1 Open Access
Notes Approved
Call Number UA @ lucian @ c:irua:6790 Serial 3234
Permanent link to this record
 

 
Author Udoh, K.-I.; El- Araby, A.M.; Tanaka, Y.; Hisatsune, K.; Yasuda, K.; Van Tendeloo, G.; van Landuyt, J.
Title Structural aspects of AuCu I or AuCu II and a cuboidal black configuration of f.c.c. disordered phase in AuCu-Pt and AuCu-Ag pseudobinary alloys Type A1 Journal article
Year 1995 Publication Materials science and engineering: part A: structural materials: properties, microstructure and processing Abbreviated Journal Mat Sci Eng A-Struct
Volume 203 Issue Pages 154-164
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Lausanne Editor
Language Wos A1995TM62800016 Publication Date 2002-07-25
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0921-5093; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 2.567 Times cited 15 Open Access
Notes Approved
Call Number UA @ lucian @ c:irua:13298 Serial 3205
Permanent link to this record
 

 
Author Delamare, M.P.; Hervieu, M.; Wang, J.; Provost, J.; Monot, I.; Verbist, K.; Van Tendeloo, G.
Title Combination of CeO2 and PtO2 doping for the strong enhancement of Jc under magnetic field in melt-textured superconductor YBaCuO Type A1 Journal article
Year 1996 Publication Physica: C : superconductivity Abbreviated Journal Physica C
Volume 262 Issue 3/4 Pages 220-226
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract A combination of CeO2 and PtO2 doping has been studied in melt-processed YBa2Cu3O7-x. This study was carried out using an optimized well established MTG process. The cerium-platinum doped samples exhibit a high fishtail effect with a J(c) of 4.3 x 10(4) A/cm(2) under an applied field of 1 T. Microstructural and nanostructural studies have been performed. The 211 and BaCeO3 inclusions are a few micrometers wide and the formation of a metastable nanocrystalline phase (Y4Ba4)Cu-8-x(Ce,Pt)(x)O-20+delta related to the perovskite is detected. The 123 grains show no specific extended defect generated by the doping process. The relationship between structure and properties are discussed.
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos A1996UV45000011 Publication Date 2003-05-13
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0921-4534; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 0.942 Times cited 27 Open Access
Notes Approved no
Call Number UA @ lucian @ c:irua:15467 Serial 397
Permanent link to this record
 

 
Author Hodges, J.P.; Slater, P.R.; Edwards, P.P.; Greaves, C.; Slaski, M.; Van Tendeloo, G.; Amelinckx, S.
Title Observation of superconductivity (Tc = 50K) in a new tetragonal alkaline-earth cuprate Sr0.8Ba1.2CuO3+\delta synthesised at ambient pressure Type A1 Journal article
Year 1996 Publication Physica: C : superconductivity Abbreviated Journal Physica C
Volume 260 Issue Pages 249-256
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos A1996UJ48400011 Publication Date 2003-05-01
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0921-4534; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 0.942 Times cited 7 Open Access
Notes Approved no
Call Number UA @ lucian @ c:irua:16872 Serial 2421
Permanent link to this record
 

 
Author Krekels, T.; Kaesche, S.; Van Tendeloo, G.
Title 2√2 ap x 2√ ap phase in superconducting ceramics Type A1 Journal article
Year 1995 Publication Physica: C : superconductivity Abbreviated Journal Physica C
Volume 248 Issue 3/4 Pages 317-327
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract By means of electron diffraction the 2 root 2 a(p) x 2 root 2 a(p) phase, well-known in YBa2Cu3O7-delta was observed in two other perovskite-based materials (Y0.75Ce0.25)(2)(Sr0.85Y0.15)(2)AlCU2O9 and Bi1.8Pb0.4Sr2Ca2Cu3O10+x. Highly correlated ordering is observed in the ab-plane, the correlation along the c-direction being weak. The plane group of the superstructure symmetry elements was determined on the basis of observed reflection conditions in diffraction patterns. Our results unambiguously rule out oxygen ordering as a possible origin of the superstructure. Experimental evidence points out that the superstructure is associated with the CuO2 layers, that are the only structural elements common to the three compounds studied. A model is proposed where the CuO2 sheet is displacively modulated. Experimental evidence suggests a correlation between adjacent CuO2 sheets. Comparison of simulated and experimental [001] zone diffraction patterns strongly supports our model.
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos A1995RJ45000012 Publication Date 2003-04-07
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0921-4534; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 0.942 Times cited 13 Open Access
Notes Approved no
Call Number UA @ lucian @ c:irua:13317 c:irua:13317 Serial 8
Permanent link to this record
 

 
Author Vasiliev, A.L.; Van Tendeloo, G.; Amelinckx, S.; Boikov, Y.; Olsson, E.; Ivanov, Z.
Title Structural aspect of YBa2Cu3O7-x films on Sis with complex barrier layers Type A1 Journal article
Year 1995 Publication Physica: C : superconductivity Abbreviated Journal Physica C
Volume 244 Issue Pages 373-388
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos A1995QQ29300025 Publication Date 2003-04-05
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0921-4534; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 0.942 Times cited 28 Open Access
Notes Approved
Call Number UA @ lucian @ c:irua:13312 Serial 3203
Permanent link to this record
 

 
Author Kopnin, E.M.; Antipov, E.V.; Capponi, J.J.; Bordet, P.; Chaillout, C.; de Brion, S.; Marezio, M.; Bobylev, A.P.; Van Tendeloo, G.
Title Suppression of superconductivity in Hg-1223 and Hg-1234 by partial replacement of Hg by carbon Type A1 Journal article
Year 1995 Publication Physica: C : superconductivity Abbreviated Journal Physica C
Volume 243 Issue Pages 222-232
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos A1995QL44700004 Publication Date 2003-04-05
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0921-4534; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 0.942 Times cited 22 Open Access
Notes Approved PHYSICS, APPLIED 28/145 Q1 #
Call Number UA @ lucian @ c:irua:13305 Serial 3387
Permanent link to this record
 

 
Author Milat, O.; Krekels, T.; Van Tendeloo, G.; Amelinckx, S.
Title The superlattices in high Tc superconducting cuprates Type A1 Journal article
Year 1994 Publication Physica: C : superconductivity Abbreviated Journal Physica C
Volume 235/240 Issue Pages 729-730
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos A1994QC69400005 Publication Date 2002-10-17
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0921-4534; ISBN Additional Links UA library record; WoS full record
Impact Factor 0.942 Times cited Open Access
Notes Approved PHYSICS, APPLIED 28/145 Q1 #
Call Number UA @ lucian @ c:irua:10048 Serial 3380
Permanent link to this record
 

 
Author Verbist, K.; Van Tendeloo, G.; Ye, M.; Mehbod, M.; Deltour, R.
Title TEM study of YBa2Cu3O7-x thin films with Zn and Fe Type A1 Journal article
Year 1994 Publication Physica: C : superconductivity Abbreviated Journal Physica C
Volume 235 Issue 1 Pages 663-664
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract Analytical and high resolution electron microscopy have been used to study the effect of Zn- and Fe-doping on the micro structure of [001] YBa2Cu3O7-x thin films on [001] MgO substrates grown by magnetron sputtering. Special attention was paid to the presence of second phase inclusions and surface outgrowths such as CuO, Y2Ba1Cu1O5-x, Y2O3 in order to establish a relationship with the critical current density.
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos A1994QA39000261 Publication Date 2002-10-17
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0921-4534; ISBN Additional Links UA library record; WoS full record
Impact Factor 0.942 Times cited Open Access
Notes Approved no
Call Number UA @ lucian @ c:irua:10047 Serial 3492
Permanent link to this record
 

 
Author Amelinckx, S.; Van Tendeloo, G.
Title Electron microscopy of recent high Tc superconductors Type A1 Journal article
Year 1994 Publication Physica: C : superconductivity Abbreviated Journal Physica C
Volume 235/240 Issue Pages 162-165
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos A1994QA39000044 Publication Date 2002-10-17
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0921-4534; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 0.942 Times cited 6 Open Access
Notes Approved no
Call Number UA @ lucian @ c:irua:10045 Serial 963
Permanent link to this record
 

 
Author Hervieu, M.; Michel, C.; Van Tendeloo, G.; Martin, C.; Maignan, A.; Raveau, B.
Title Copper oxycarbonates and mercury based cuprates: structural mechanisms of new superconductors Type A1 Journal article
Year 1994 Publication Physica: C : superconductivity Abbreviated Journal Physica C
Volume 235/240 Issue Pages 25-28
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos A1994QA39000011 Publication Date 2002-10-17
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0921-4534; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 0.942 Times cited 8 Open Access
Notes Approved COMPUTER SCIENCE, INTERDISCIPLINARY 11/104 Q1 # PHYSICS, MATHEMATICAL 1/53 Q1 #
Call Number UA @ lucian @ c:irua:10046 Serial 517
Permanent link to this record
 

 
Author Van Tendeloo, G.; Chaillout, C.; Capponi, J.J.; Marezio, M.; Antipov, E.V.
Title Atomic structure and defect structure of the superconducting HgBa2Can-1CunO2n+2+\delta homologous series Type A1 Journal article
Year 1994 Publication Physica: C : superconductivity Abbreviated Journal Physica C
Volume 223 Issue 3/4 Pages 219-226
Keywords A1 Journal article; Electron microscopy for materials research (EMAT)
Abstract The perfect as well as the defect structure of several members of the superconducting family HgBa2Can-1CunO2n+2+delta have been studied in detail by electron diffraction and high-resolution electron microscopy Identification of the cation configuration is possible, even in the defect regions, with the help of computer simulations. The fine structure of several defects is analyzed in detail, the most common defect being the intergrowth of slabs corresponding to different n values in the title formula. In general, however, the crystals are of a high perfection, particularly for the lower n members. The occurrence of double (HgO)delta layers is seen occasionally, indicating the possible existence of a material with a double mercury layer. Some of these defects are possibly related to recently discovered anomalies at 250 K in these compounds.
Address
Corporate Author Thesis
Publisher Place of Publication Amsterdam Editor
Language Wos A1994NG47600003 Publication Date 2002-10-17
Series Editor Series Title Abbreviated Series Title
Series Volume Series Issue Edition
ISSN 0921-4534; ISBN Additional Links UA library record; WoS full record; WoS citing articles
Impact Factor 0.942 Times cited 30 Open Access
Notes Approved no
Call Number UA @ lucian @ c:irua:10028 Serial 196
Permanent link to this record