Records |
Author |
Shi, H.; Pourbabak, S.; Van Humbeeck, J.; Schryvers, D. |
Title |
Electron microscopy study of Nb-rich nanoprecipitates in NiTiNb and their influence on the martensitic transformation |
Type |
A1 Journal article |
Year |
2012 |
Publication |
Scripta materialia |
Abbreviated Journal |
Scripta Mater |
Volume |
67 |
Issue |
12 |
Pages |
939-942 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
Nb-rich nanoprecipitates in the matrix of an annealed commercial NiTiNb alloy are investigated by scanning and transmission electron microscopy, including slice-and-view and chemical analysis. The precipitates have a diameter of around 100 nm, are faceted and have a cube-on-cube relation with the B2 matrix. In situ TEM cooling shows that the martensitic transformation is hampered by the presence of these precipitates. The latter could explain the increase in hysteresis when compared with the binary system. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
Language |
|
Wos |
000311135000005 |
Publication Date |
2012-08-27 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1359-6462; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.747 |
Times cited |
29 |
Open Access |
|
Notes |
Fwo |
Approved |
Most recent IF: 3.747; 2012 IF: 2.821 |
Call Number |
UA @ lucian @ c:irua:101486 |
Serial |
971 |
Permanent link to this record |
|
|
|
Author |
Renard, K.; Idrissi, H.; Schryvers, D.; Jacques, P.J. |
Title |
On the stress state dependence of the twinning rate and work hardening in twinning-induced plasticity steels |
Type |
A1 Journal article |
Year |
2012 |
Publication |
Scripta materialia |
Abbreviated Journal |
Scripta Mater |
Volume |
66 |
Issue |
12 |
Pages |
966-971 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
The influence of the stress state on the twinning rate and work hardening is studied in the case of an FeMnC TWIP steel strained in uniaxial tension, simple shear and rolling. The resulting stressstrain responses exhibit marked differences. The twinning rate, number of activated twinning systems in each grain, twin thickness and transmission of twins across grain boundaries are dependent on the imposed stress state during straining. Relationships between twin features and macroscopic work hardening rate are established. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
Language |
|
Wos |
000304641500004 |
Publication Date |
2012-02-10 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1359-6462; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.747 |
Times cited |
41 |
Open Access |
|
Notes |
Iap |
Approved |
Most recent IF: 3.747; 2012 IF: 2.821 |
Call Number |
UA @ lucian @ c:irua:98374 |
Serial |
2454 |
Permanent link to this record |
|
|
|
Author |
Cao, S.; Pourbabak, S.; Schryvers, D. |
Title |
Quantitative 3-D morphologic and distributional study of Ni4Ti3 precipitates in a Ni51Ti49 single crystal alloy |
Type |
A1 Journal article |
Year |
2012 |
Publication |
Scripta materialia |
Abbreviated Journal |
Scripta Mater |
Volume |
66 |
Issue |
9 |
Pages |
650-653 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
The size, shape and distribution of Ni4Ti3 precipitates in Ni51Ti49 single crystals annealed under stress-free and 〈1 1 1〉B2 compressive conditions are studied via focused ion beam/scanning electron microscopy slice-and-view. The precipitates in the stress-free material grow in autocatalytic pockets with larger size, lower number density, flatter shape and larger inter-particle distance than in the compressed material. Nevertheless, a new quantification method called water penetration reveals that, due to the precipitate alignment, martensite can grow more easily in the compressed material perpendicular to the compression direction. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
Language |
|
Wos |
000302425100010 |
Publication Date |
2012-01-30 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1359-6462; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.747 |
Times cited |
8 |
Open Access |
|
Notes |
Fwo |
Approved |
Most recent IF: 3.747; 2012 IF: 2.821 |
Call Number |
UA @ lucian @ c:irua:97387 |
Serial |
2743 |
Permanent link to this record |
|
|
|
Author |
Wang, B.; Idrissi, H.; Shi, H.; Colla, M.S.; Michotte, S.; Raskin, J.P.; Pardoen, T.; Schryvers, D. |
Title |
Texture-dependent twin formation in nanocrystalline thin Pd films |
Type |
A1 Journal article |
Year |
2012 |
Publication |
Scripta materialia |
Abbreviated Journal |
Scripta Mater |
Volume |
66 |
Issue |
11 |
Pages |
866-871 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
Nanocrystalline Pd films were produced by electron-beam evaporation and sputter deposition. The electron-beam-evaporated films reveal randomly oriented nanograins with a relatively high density of growth twins, unexpected in view of the high stacking fault energy of Pd. In contrast, sputter-deposited films show a clear 〈1 1 1〉 crystallographic textured nanostructure without twins. These results provide insightful information to guide the generation of microstructures with enhanced strength/ductility balance in high stacking fault energy nanocrystalline metallic thin films. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
Language |
|
Wos |
000303621900007 |
Publication Date |
2012-01-31 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1359-6462; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.747 |
Times cited |
19 |
Open Access |
|
Notes |
Iap; Fwo |
Approved |
Most recent IF: 3.747; 2012 IF: 2.821 |
Call Number |
UA @ lucian @ c:irua:96955 |
Serial |
3566 |
Permanent link to this record |
|
|
|
Author |
Idrissi, H.; Renard, K.; Schryvers, D.; Jacques, P.J. |
Title |
On the relationship between the twin internal structure and the work-hardening rate of TWIP steels |
Type |
A1 Journal article |
Year |
2010 |
Publication |
Scripta materialia |
Abbreviated Journal |
Scripta Mater |
Volume |
63 |
Issue |
10 |
Pages |
961-964 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
FeMnC and FeMnSiAl TWIP steels deformed under the same conditions exhibit different work-hardening rates. The present study investigates the microstructure of plastically deformed FeMnC and FeMnSiAl samples, particularly the internal structure of the mechanically generated twins and their topology at the grain scale. Twins in the FeMnC steel are finer and full of sessile dislocations, rendering this material distinctly stronger with an improved work-hardening rate. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
Language |
|
Wos |
000282461800003 |
Publication Date |
2010-07-20 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1359-6462; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.747 |
Times cited |
145 |
Open Access |
|
Notes |
Iap |
Approved |
Most recent IF: 3.747; 2010 IF: 2.820 |
Call Number |
UA @ lucian @ c:irua:84472 |
Serial |
2452 |
Permanent link to this record |
|
|
|
Author |
Cao, S.; Somsen, C.; Croitoru, M.; Schryvers, D.; Eggeler, G. |
Title |
Focused ion beam/scanning electron microscopy tomography and conventional transmission electron microscopy assessment of Ni4Ti3 morphology in compression-aged Ni-rich Ni-Ti single crystals |
Type |
A1 Journal article |
Year |
2010 |
Publication |
Scripta materialia |
Abbreviated Journal |
Scripta Mater |
Volume |
62 |
Issue |
6 |
Pages |
399-402 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT); Condensed Matter Theory (CMT) |
Abstract |
The size, morphology and configuration of Ni4Ti3 precipitates in a single-crystal NiTi alloy have been investigated by two-dimensional transmission electron microscopy-based image analysis and three-dimensional reconstruction from slice-and-view images obtained in a focused ion beam/scanning electron microscopy (FIB/SEM) dual-beam system. Average distances between the precipitates measured along the compression direction correlate well between both techniques, while particle shape and configuration data is best obtained from FIB/SEM. Precipitates form pockets of B2 of 0.54 ìm in the compression direction and 1 ìm perpendicular to the compression direction. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
Language |
|
Wos |
000275072700020 |
Publication Date |
2009-12-04 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1359-6462; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.747 |
Times cited |
16 |
Open Access |
|
Notes |
Fwo |
Approved |
Most recent IF: 3.747; 2010 IF: 2.820 |
Call Number |
UA @ lucian @ c:irua:79817 |
Serial |
1246 |
Permanent link to this record |
|
|
|
Author |
Idrissi, H.; Ryelandt, L.; Veron, M.; Schryvers, D.; Jacques, P.J. |
Title |
Is there a relationship between the stacking fault character and the activated mode of plasticity of FeMn-based austenitic steels? |
Type |
A1 Journal article |
Year |
2009 |
Publication |
Scripta materialia |
Abbreviated Journal |
Scripta Mater |
Volume |
60 |
Issue |
11 |
Pages |
941-944 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
By changing the testing temperature, an austenitic FeMnAlSi alloy presents either å-martensite transformation or mechanical twinning during straining. In order to understand the nucleation and growth mechanisms involved in both phenomena, defects and particularly stacking faults, were characterized by transmission electron microscopy. It is observed that the character of the stacking faults also changes (from extrinsic to intrinsic) together with the temperature and the activated mode of plasticity. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
Language |
|
Wos |
000265359900005 |
Publication Date |
2009-02-10 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1359-6462; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.747 |
Times cited |
84 |
Open Access |
|
Notes |
Iap |
Approved |
Most recent IF: 3.747; 2009 IF: 2.949 |
Call Number |
UA @ lucian @ c:irua:77276 |
Serial |
1751 |
Permanent link to this record |
|
|
|
Author |
Delville, R.; Schryvers, D.; Zhang, Z.; James, R.D. |
Title |
Transmission electron microscopy investigation of microstructures in low-hysteresis alloys with special lattice parameters |
Type |
A1 Journal article |
Year |
2009 |
Publication |
Scripta materialia |
Abbreviated Journal |
Scripta Mater |
Volume |
60 |
Issue |
5 |
Pages |
293-296 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
A sharp drop in hysteresis is observed for shape memory alloys satisfying the compatibility condition between austenite and martensite, i.e. ë2 = 1, where ë2 is the middle eigenvalue of the transformation strain matrix. The present work investigates the evolution of microstructure by transmission electron microscopy as the composition of the Ti50Ni50−xPdx system is systemically tuned to achieve the condition ë2 = 1. Changes in morphology, twinning density and twinning modes are reported along with twinless martensite and exact austenitemartensite interfaces. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
Language |
|
Wos |
000262553300007 |
Publication Date |
2008-11-08 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1359-6462; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.747 |
Times cited |
56 |
Open Access |
|
Notes |
Multimat |
Approved |
Most recent IF: 3.747; 2009 IF: 2.949 |
Call Number |
UA @ lucian @ c:irua:76017 |
Serial |
3710 |
Permanent link to this record |
|
|
|
Author |
Bartova, B.; Schryvers, D.; Yang, Z.; Ignacova, S.; Sittner, P. |
Title |
Microstructure and precipitates in as-cast Co38Ni33Al29 shape memory alloy |
Type |
A1 Journal article |
Year |
2007 |
Publication |
Scripta materialia |
Abbreviated Journal |
Scripta Mater |
Volume |
57 |
Issue |
1 |
Pages |
37-40 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
Language |
|
Wos |
000246632900010 |
Publication Date |
2007-04-13 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1359-6462; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.747 |
Times cited |
22 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 3.747; 2007 IF: 2.481 |
Call Number |
UA @ lucian @ c:irua:64753 |
Serial |
2059 |
Permanent link to this record |
|
|
|
Author |
Yang, Z.; Tirry, W.; Schryvers, D. |
Title |
Analytical TEM investigations on concentration gradients surrounding Ni4Ti3 precipitates in Ni-Ti shape memory material |
Type |
A1 Journal article |
Year |
2005 |
Publication |
Scripta materialia |
Abbreviated Journal |
Scripta Mater |
Volume |
52 |
Issue |
11 |
Pages |
1129-1134 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
Language |
|
Wos |
000228190200010 |
Publication Date |
2005-03-16 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1359-6462; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.747 |
Times cited |
49 |
Open Access |
|
Notes |
GOA project; MCRTN-FP6-505226 Multimat |
Approved |
Most recent IF: 3.747; 2005 IF: 2.228 |
Call Number |
UA @ lucian @ c:irua:55687 |
Serial |
110 |
Permanent link to this record |
|
|
|
Author |
Santamarta, R.; Schryvers, D. |
Title |
Effect of amorphous-crystalline interfaces on the martensitic transformation in Ti50Ni25Cu25 |
Type |
A1 Journal article |
Year |
2004 |
Publication |
Scripta materialia |
Abbreviated Journal |
Scripta Mater |
Volume |
50 |
Issue |
|
Pages |
1423-1427 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
Language |
|
Wos |
000221009500002 |
Publication Date |
2004-04-13 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1359-6462; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.747 |
Times cited |
29 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 3.747; 2004 IF: 2.112 |
Call Number |
UA @ lucian @ c:irua:48379 |
Serial |
795 |
Permanent link to this record |
|
|
|
Author |
Schalm, O.; van der Linden, V.; Frederickx, P.; Luyten, S.; van der Snickt, G.; Caen, J.; Schryvers, D.; Janssens, K.; Cornelis, E.; van Dyck, D.; Schreiner, M. |
Title |
Enamels in stained glass windows: preparation, chemical composition, microstructure and causes of deterioration |
Type |
A1 Journal article |
Year |
2009 |
Publication |
Spectrochimica acta: part B : atomic spectroscopy |
Abbreviated Journal |
Spectrochim Acta B |
Volume |
64 |
Issue |
8 |
Pages |
812-820 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT); AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Vision lab |
Abstract |
Stained glass windows incorporating dark blue and purple enamel paint layers are in some cases subject to severe degradation while others from the same period survived the ravages of time. A series of dark blue, greenblue and purple enamel glass paints from the same region (Northwestern Europe) and from the same period (16early 20th centuries) has been studied by means of a combination of microscopic X-ray fluorescence analysis, electron probe micro analysis and transmission electron microscopy with the aim of better understanding the causes of the degradation. The chemical composition of the enamels diverges from the average chemical composition of window glass. Some of the compositions appear to be unstable, for example those with a high concentration of K2O and a low content of CaO and PbO. In other cases, the deterioration of the paint layers was caused by the less than optimal vitrification of the enamel during the firing process. Recipes and chemical compositions indicate that glassmakers of the 1617th century had full control over the color of the enamel glass paints they made. They mainly used three types of coloring agents, based on Co (dark blue), Mn (purple) and Cu (light-blue or greenblue) as coloring elements. Bluepurple enamel paints were obtained by mixing two different coloring agents. The coloring agent for redpurple enamel, introduced during the 19th century, was colloidal gold embedded in grains of lead glass. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
Language |
|
Wos |
000269995300018 |
Publication Date |
2009-06-19 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0584-8547; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.241 |
Times cited |
28 |
Open Access |
|
Notes |
Iuap Vi/6; Fwo; Goa |
Approved |
Most recent IF: 3.241; 2009 IF: 2.719 |
Call Number |
UA @ lucian @ c:irua:79647 |
Serial |
1035 |
Permanent link to this record |
|
|
|
Author |
Marteleur, M.; Idrissi, H.; Amin-Ahmadi, B.; Prima, F.; Schryvers, D.; Jacques, P.J. |
Title |
On the nucleation mechanism of {112} < 111 > mechanical twins in as-quenched beta metastable Ti-12 wt.% Mo alloy |
Type |
A1 Journal article |
Year |
2019 |
Publication |
Materialia |
Abbreviated Journal |
|
Volume |
7 |
Issue |
|
Pages |
Unsp 100418 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Recently developed beta-metastable Ti grades take advantage of the simultaneous activation of TRIP and TWIP effects for enhancing their work hardening rate. However, the role of each plasticity mechanism on the macroscopic mechanical response is still unclear. In this work, the nucleation mechanism of the first activated plasticity mechanism, namely {112} < 111 > twinning, was investigated. Firstly, post-mortem TEM analysis showed that twins nucleate on pre-existing microstructural defects such as thermal jogs with the zonal dislocation mechanism. The precipitation of the omega phase on twin boundaries has been observed, as well as the emission of numerous dislocations from super-jogs present in these twin boundaries. It is also shown that {112} < 111 > twins act as effective dislocation sources for the subsequent plasticity mechanisms such as beta -> alpha '' martensitic transformation and {332} < 111 > twinning. Secondly, in situ TEM tensile testing of the investigated Ti grade highlighted the primary role of the initial defect configuration present in the microstructure. It is shown that twins cannot nucleate without the presence of specific defects allowing the triggering of the dislocation decomposition needed for the twinning mechanism highlighted in investigated bulk samples. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000537131000052 |
Publication Date |
2019-07-31 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
2589-1529 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
|
Open Access |
|
Notes |
|
Approved |
no |
Call Number |
UA @ admin @ c:irua:170326 |
Serial |
6875 |
Permanent link to this record |
|
|
|
Author |
Coghe, F.; Tirry, W.; Rabet, L.; Schryvers, D.; Van Houtte, P. |
Title |
Importance of twinning in static and dynamic compression of a Ti-6Al-4V titanium alloy with an equiaxed microstructure |
Type |
A1 Journal article |
Year |
2012 |
Publication |
Materials science and engineering: part A: structural materials: properties, microstructure and processing |
Abbreviated Journal |
Mat Sci Eng A-Struct |
Volume |
537 |
Issue |
|
Pages |
1-10 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
Whereas deformation twinning is known to be an important deformation mechanism for hexagonal materials like magnesium and pure titanium, so far almost no literature exists on the twinning behaviour of the Ti-6Al-4V alloy. In this work it was shown that the activation of twinning as a deformation mechanism could have a pronounced effect on the mechanical behaviour of the Ti-6Al-4V alloy. This effect is even more pronounced under dynamic loading conditions. Transmission electron microscopy showed that only the {1 0 1 2}{1 0 1 1} tensile twin system was activated under certain loading conditions. Light-optical microscopy and electron backscatter diffraction data were afterwards used to experimentally determine the twin fractions. The importance of twinning for the texture evolution was also studied. It was shown that even small twin fractions can lead to distinct texture features, especially due to the discrete reorientation of the c-axes. The experimental results were compared to simulated results that were obtained with a viscoplastic self-consistent crystal plasticity code, after experimental validation that twinning can be reliably modelled as a unidirectional slip system. Although good agreement was obtained for the experimental and simulated stress-strain curves, the simulated results concerning twinning correlated well only on a qualitative basis as the simulated twin fractions were systematically higher than the experimental fractions. This seems to strengthen the hypothesis made by other research groups that complete grains might reorient by twinning. (C) 2011 Elsevier B.V. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
000301473300001 |
Publication Date |
2011-12-21 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0921-5093; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.094 |
Times cited |
35 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 3.094; 2012 IF: 2.108 |
Call Number |
UA @ lucian @ c:irua:97818 |
Serial |
1565 |
Permanent link to this record |
|
|
|
Author |
Tirry, W.; Coghe, F.; Bouvier, S.; Gasperini, M.; Rabet, L.; Schryvers, D. |
Title |
A multi-scale characterization of deformation twins in Ti6Al4V sheet material deformed by simple shear |
Type |
A1 Journal article |
Year |
2010 |
Publication |
Materials science and engineering: part A: structural materials: properties, microstructure and processing |
Abbreviated Journal |
Mat Sci Eng A-Struct |
Volume |
527 |
Issue |
16/17 |
Pages |
4136-4145 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Ti6Al4V sheet material is subjected to simple shear deformation with strain ratio's of 10%, 30% and 50%. Optical microscopy, transmission electron microscopy and electron backscatter diffraction techniques are applied to study the presence and morphology of deformation twins. Only the View the MathML source type of twins seems to be present with a volume fraction below 1%. These View the MathML source twins show a high density of basal stacking faults of the ABABACAC type identified using atomic resolution transmission electron microscopy. A resolved shear stress analysis shows that twins most often occur on those planes with the highest resolved shear stresses, but that the starting texture is not beneficial for the occurrence of twins. It is further suggested that a transitory strain hardening regime observed around 530 MPa might be related with the onset of twinning. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
000278766800068 |
Publication Date |
2010-03-23 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0921-5093; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.094 |
Times cited |
20 |
Open Access |
|
Notes |
Iap |
Approved |
Most recent IF: 3.094; 2010 IF: 2.101 |
Call Number |
UA @ lucian @ c:irua:82291 |
Serial |
2212 |
Permanent link to this record |
|
|
|
Author |
Yang, Z.Q.; Schryvers, D. |
Title |
Electron energy-loss spectroscopy study of NiTi shape memory alloys |
Type |
A1 Journal article |
Year |
2008 |
Publication |
Materials science and engineering: part A: structural materials: properties, microstructure and processing |
Abbreviated Journal |
Mat Sci Eng A-Struct |
Volume |
481 |
Issue |
|
Pages |
214-217 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000255716100041 |
Publication Date |
2007-06-11 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0921-5093; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.094 |
Times cited |
7 |
Open Access |
|
Notes |
Gao |
Approved |
Most recent IF: 3.094; 2008 IF: 1.806 |
Call Number |
UA @ lucian @ c:irua:69156 |
Serial |
934 |
Permanent link to this record |
|
|
|
Author |
Srivastava, A.K.; Yang, Z.; Schryvers, D.; van Hurnbeeck, J. |
Title |
Effect of annealing on cold-rolled Ni-Ti alloys |
Type |
A1 Journal article |
Year |
2008 |
Publication |
Materials science and engineering: part A: structural materials: properties, microstructure and processing |
Abbreviated Journal |
Mat Sci Eng A-Struct |
Volume |
481 |
Issue |
Si |
Pages |
594-597 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000255716100123 |
Publication Date |
2007-06-07 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0921-5093; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.094 |
Times cited |
8 |
Open Access |
|
Notes |
Fwo; G0465.05 |
Approved |
Most recent IF: 3.094; 2008 IF: 1.806 |
Call Number |
UA @ lucian @ c:irua:69141 |
Serial |
797 |
Permanent link to this record |
|
|
|
Author |
Tirry, W.; Schryvers, D. |
Title |
In situ transmission electron microscopy of stress-induced martensite with focus on martensite twinning |
Type |
A1 Journal article |
Year |
2008 |
Publication |
Materials science and engineering: part A: structural materials: properties, microstructure and processing |
Abbreviated Journal |
Mat Sci Eng A-Struct |
Volume |
481 |
Issue |
Si |
Pages |
420-425 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000255716100087 |
Publication Date |
2007-06-07 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0921-5093; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.094 |
Times cited |
22 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 3.094; 2008 IF: 1.806 |
Call Number |
UA @ lucian @ c:irua:69139 |
Serial |
1586 |
Permanent link to this record |
|
|
|
Author |
Rotaru, G.-M.; Schryvers, D. |
Title |
New (3(3)under-bar) long-period microtwin variant in the martensitic phase of the PtTi alloy |
Type |
A1 Journal article |
Year |
2008 |
Publication |
Materials science and engineering: part A: structural materials: properties, microstructure and processing |
Abbreviated Journal |
Mat Sci Eng A-Struct |
Volume |
481 |
Issue |
Si |
Pages |
437-441 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000255716100090 |
Publication Date |
2007-06-07 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0921-5093; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.094 |
Times cited |
3 |
Open Access |
|
Notes |
Multimat |
Approved |
Most recent IF: 3.094; 2008 IF: 1.806 |
Call Number |
UA @ lucian @ c:irua:69140 |
Serial |
2300 |
Permanent link to this record |
|
|
|
Author |
Schryvers, D.; Tirry, W.; Yang, Z.Q.; |
Title |
Measuring strain fields and concentration gradients around Ni4Ti3 precipitates |
Type |
A1 Journal article |
Year |
2006 |
Publication |
Materials science and engineering A: structural materials properties microstructure and processing |
Abbreviated Journal |
Mat Sci Eng A-Struct |
Volume |
438 |
Issue |
|
Pages |
485-488 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000242900900105 |
Publication Date |
2006-07-12 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0921-5093; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.094 |
Times cited |
35 |
Open Access |
|
Notes |
Goa |
Approved |
Most recent IF: 3.094; 2006 IF: 1.490 |
Call Number |
UA @ lucian @ c:irua:62329 |
Serial |
1969 |
Permanent link to this record |
|
|
|
Author |
Tirry, W.; Schryvers, D.; Jorissen, K.; Lamoen, D. |
Title |
Quantitative determination of the crystal structure of Ni4Ti3 precipitates |
Type |
A1 Journal article |
Year |
2006 |
Publication |
Materials science and engineering: part A: structural materials: properties, microstructure and processing |
Abbreviated Journal |
Mat Sci Eng A-Struct |
Volume |
438 |
Issue |
|
Pages |
517-520 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
000242900900112 |
Publication Date |
2006-07-12 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0921-5093; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.094 |
Times cited |
7 |
Open Access |
|
Notes |
Mrtn-Ct-2004-505226 |
Approved |
Most recent IF: 3.094; 2006 IF: 1.490 |
Call Number |
UA @ lucian @ c:irua:61577 |
Serial |
2752 |
Permanent link to this record |
|
|
|
Author |
Santamarta, R.; Schryvers, D. |
Title |
Structure of multi-grain spherical particles in an amorphous Ti50Ni25Cu25 melt-spun ribbon |
Type |
A1 Journal article |
Year |
2004 |
Publication |
Materials science and engineering: part A: structural materials: properties, microstructure and processing |
Abbreviated Journal |
Mat Sci Eng A-Struct |
Volume |
378 |
Issue |
1/2 |
Pages |
143-147 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
000223329900025 |
Publication Date |
2004-04-10 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0921-5093; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.094 |
Times cited |
5 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 3.094; 2004 IF: 1.445 |
Call Number |
UA @ lucian @ c:irua:48784 |
Serial |
3311 |
Permanent link to this record |
|
|
|
Author |
Tirry, W.; Schryvers, D. |
Title |
High resolution TEM study of Ni4Ti3 precipitates in austenitic Ni51Ti49 |
Type |
A1 Journal article |
Year |
2004 |
Publication |
Materials science and engineering: part A: structural materials: properties, microstructure and processing |
Abbreviated Journal |
Mat Sci Eng A-Struct |
Volume |
378 |
Issue |
1/2 |
Pages |
157-160 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
000223329900028 |
Publication Date |
2004-04-10 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0921-5093; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.094 |
Times cited |
19 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 3.094; 2004 IF: 1.445 |
Call Number |
UA @ lucian @ c:irua:48785 |
Serial |
1461 |
Permanent link to this record |
|
|
|
Author |
Schryvers, D.; Potapov, P.; Santamarta, R.; Tirry, W. |
Title |
Applications of advanced transmission electron microscopic techniques to Ni-Ti based shape memory materials |
Type |
A1 Journal article |
Year |
2004 |
Publication |
Materials science and engineering: part A: structural materials: properties, microstructure and processing |
Abbreviated Journal |
Mat Sci Eng A-Struct |
Volume |
378 |
Issue |
1/2 |
Pages |
11-15 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
000223329900003 |
Publication Date |
2004-03-23 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0921-5093; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.094 |
Times cited |
6 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 3.094; 2004 IF: 1.445 |
Call Number |
UA @ lucian @ c:irua:48783 |
Serial |
145 |
Permanent link to this record |
|
|
|
Author |
Yang, Z.; Schryvers, D. |
Title |
Study of changes in composition and EELS ionization edges upon Ni4Ti3 precipitation in a NiTi alloy |
Type |
A1 Journal article |
Year |
2006 |
Publication |
Micron |
Abbreviated Journal |
Micron |
Volume |
37 |
Issue |
5 |
Pages |
503-507 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000238806400020 |
Publication Date |
2005-09-08 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0968-4328; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
1.98 |
Times cited |
10 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 1.98; 2006 IF: 1.200 |
Call Number |
UA @ lucian @ c:irua:59605 |
Serial |
3327 |
Permanent link to this record |
|
|
|
Author |
Zhou, C.; Ji, G.; Chen, Z.; Wang, M.; Addad, A.; Schryvers, D.; Wang, H. |
Title |
Fabrication, interface characterization and modeling of oriented graphite flakes/Si/Al composites for thermal management applications |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Materials and design |
Abbreviated Journal |
Mater Design |
Volume |
63 |
Issue |
|
Pages |
719-728 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Highly thermally conductive graphite flakes (Gf)/Si/Al composites have been fabricated using Gf, Si powder and an AlSi7Mg0.3 alloy by an optimized pressure infiltration process for thermal management applications. In the composites, the layers of Gf were spaced apart by Si particles and oriented perpendicular to the pressing direction, which offered the opportunity to tailor the thermal conductivity (TC) and coefficient of thermal expansion (CTE) of the composites. Microstructural characterization revealed that the formation of a clean and tightly-adhered interface at the nanoscale between the side surface of the Gf and Al matrix, devoid of a detrimental Al4C3 phase and a reacted amorphous AlSiOC layer, contributed to excellent thermal performance along the alignment direction. With increasing volume fraction of Gf from 13.7 to 71.1 vol.%, the longitudinal (i.e. parallel to the graphite layers) TC of the composites increased from 179 to 526 W/m K, while the longitudinal CTE decreased from 12.1 to 7.3 ppm/K (matching the values of electronic components). Furthermore, the modified layers-in-parallel model better fitted the longitudinal TC data than the layers-in-parallel model and confirmed that the clean and tightly-adhered interface is favorable for the enhanced longitudinal TC. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Reigate |
Editor |
|
Language |
|
Wos |
000340949300086 |
Publication Date |
2014-07-17 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0261-3069; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
61 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: NA |
Call Number |
UA @ lucian @ c:irua:118124 |
Serial |
1166 |
Permanent link to this record |
|
|
|
Author |
Ji, G.; Tan, Z.; Shabadi, R.; Li, Z.; Grünewald, W.; Addad, A.; Schryvers, D.; Zhang, D. |
Title |
Triple ion beam cutting of diamond/Al composites for interface characterization |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Materials characterization |
Abbreviated Journal |
Mater Charact |
Volume |
89 |
Issue |
|
Pages |
132-137 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
A novel triple ion beam cutting technique was employed to prepare high-quality surfaces of diamond/Al composites for interfacial characterization, which has been unachievable so far. Near-perfect and artifact-free surfaces were obtained without mechanical pre-polishing. Hence, the as-prepared surfaces are readily available for further study and also, ready to be employed in a focus ion beam system for preferential selection of transmission electron microscopy samples. Dramatically different diamond/Al interface configurations – sub-micrometer Al2O3 particles and clean interfaces were unambiguously revealed. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
New York |
Editor |
|
Language |
|
Wos |
000333513400015 |
Publication Date |
2014-01-18 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1044-5803; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.714 |
Times cited |
9 |
Open Access |
|
Notes |
Fwo |
Approved |
Most recent IF: 2.714; 2014 IF: 1.845 |
Call Number |
UA @ lucian @ c:irua:113394 |
Serial |
3735 |
Permanent link to this record |
|
|
|
Author |
Peirs, J.; Tirry, W.; Amin-Ahmadi, B.; Coghe, F.; Verleysen, P.; Rabet, L.; Schryvers, D.; Degrieck, J. |
Title |
Microstructure of adiabatic shear bands in Ti6Al4V |
Type |
A1 Journal article |
Year |
2013 |
Publication |
Materials characterization |
Abbreviated Journal |
Mater Charact |
Volume |
75 |
Issue |
|
Pages |
79-92 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Microstructural deformation mechanisms in adiabatic shear bands in Ti6Al4V are studied using traditional TEM and selected area diffraction, and more advanced microstructural characterisation techniques such as energy dispersive X-ray spectroscopy, high angle annular dark field STEM and conical dark field TEM. The shear bands under investigation are induced in Ti6Al4V samples by high strain rate compression of cylindrical and hat-shaped specimens in a split Hopkinson pressure bar setup. Samples from experiments interrupted at different levels of deformation are used to study the evolution of the microstructure in and nearby the shear bands. From the early stages of adiabatic shear band formation, TEM revealed strongly elongated equiaxed grains in the shear band. These band-like grains become narrower towards the centre of the band and start to fraction even further along their elongated direction to finally result in a nano-crystalline region in the core. In fully developed shear bands, twins and a needle-like martensite morphology are observed near the shear band. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
New York |
Editor |
|
Language |
|
Wos |
000314860900011 |
Publication Date |
2012-11-07 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1044-5803; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.714 |
Times cited |
56 |
Open Access |
|
Notes |
Iuap; Fwo |
Approved |
Most recent IF: 2.714; 2013 IF: 1.925 |
Call Number |
UA @ lucian @ c:irua:105300 |
Serial |
2065 |
Permanent link to this record |
|
|
|
Author |
Tirry, W.; Bouvier, S.; Benmhenni, N.; Hammami, W.; Habraken, A.M.; Coghe, F.; Schryvers, D.; Rabet, L. |
Title |
Twinning in pure Ti subjected to monotonic simple shear deformation |
Type |
A1 Journal article |
Year |
2012 |
Publication |
Materials characterization |
Abbreviated Journal |
Mater Charact |
Volume |
72 |
Issue |
|
Pages |
24-36 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
The aim of this paper is to provide a thorough study on the occurrence and importance of deformation twinning in simple shear deformed pure α-Ti. A statistically relevant inspection of the morphology of the deformation twins in relation to the applied strain/deformation is performed. The investigated microstructural aspects are the twin volume fraction, the twin thickness distribution and the resolved shear stress distribution on the twin plane. All these aspects are examined as a function of the twin types and two initial textures. Monotonic simple shear experiments are carried out for three different loading directions with respect to a direction linked to the initial crystallographic texture. EBSD and TEM observations reveal the presence of View the MathML source and View the MathML source twins. The statistical analysis reveals that View the MathML source and View the MathML source twins have a similar average thickness around 1.9 nm, but the View the MathML source twins show a far larger spread on their thickness and can grow to almost the size of the original parent grain. Correlation of the twin fractions with the RSS analysis shows that RSS is an acceptable method explaining the difference in twin fractions for different textures and orientations. A detailed analysis shows that View the MathML source twins occur in average with a smaller volume fraction but with a higher RSS, indicating they are more difficult to nucleate or grow compared to View the MathML source twinning. In general a higher RSS value on the twin plane is not connected to a higher twin thickness; only in the case of View the MathML source twins the highest RSS values show clearly thicker twins. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
New York |
Editor |
|
Language |
|
Wos |
000309086700004 |
Publication Date |
2012-07-10 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1044-5803; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.714 |
Times cited |
25 |
Open Access |
|
Notes |
Iap |
Approved |
Most recent IF: 2.714; 2012 IF: 1.880 |
Call Number |
UA @ lucian @ c:irua:101225 |
Serial |
3768 |
Permanent link to this record |
|
|
|
Author |
Cautaerts, N.; Delville, R.; Stergar, E.; Schryvers, D.; Verwerft, M. |
Title |
Tailoring the Ti-C nanoprecipitate population and microstructure of titanium stabilized austenitic steels |
Type |
A1 Journal article |
Year |
2018 |
Publication |
Journal of nuclear materials |
Abbreviated Journal |
J Nucl Mater |
Volume |
507 |
Issue |
507 |
Pages |
177-187 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
The present work reports on the microstructural evolution of a new heat of 24% cold worked austenitic DIN 1.4970 (15-15Ti) nuclear cladding steel subjected to ageing heat treatments of varying duration between 500 and 800 degrees C (by steps of 100 degrees C). The primary aim was studying the finely dispersed Ti-C nanoprecipitate population, which are thought to be beneficial for creep and swelling resistance during service. Their size distribution and number density were estimated through dark field imaging and bright field Moire imaging techniques in the transmission electron microscope. Nanoprecipitates formed at and above 600 degrees C, which is a lower temperature than previously reported. The observed nucleation, growth and coarsening behavior of the nanoprecipitates were consistent with simple diffusion arguments. The formation of nanoprecipitates coincided with significant dissociation of dislocations as evidenced by weak beam dark field imaging. Possible mechanisms, including Silcock's stacking fault growth model and Suzuki segregation, are discussed. Recrystallization observed after extended ageing at 800 degrees C caused the redissolution of nanoprecipitates. Large primary Ti(C,N) and (Ti,Mo)C precipitates that occur in the as-received material, and M23C6 precipitates that nucleate on grain boundaries at low temperatures were also characterized by a selective dissolution procedure involving filtration, X-ray diffraction and quantitative Rietveld refinement. The partitioning of key elements between the different phases was derived by combining these findings and was consistent with thermodynamic considerations and the processing history of the steel. (C) 2018 Elsevier B.V. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
Language |
|
Wos |
000438019800021 |
Publication Date |
2018-04-30 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0022-3115 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.048 |
Times cited |
1 |
Open Access |
Not_Open_Access |
Notes |
; We would like to acknowledge ENGIE, SCK.CEN, the SCK.CEN academy and the MYRRHA project for the financial support of this work. Special thanks to T. Wangle and P. Dries for their help with filtration and gravimetry. Also thanks to Dr. G. Leinders for the discussions on XRD and Rietveld refinement. Thanks to E. Charalampopoulou and A. Youssef for assisting with the dissolution experiments. ; |
Approved |
Most recent IF: 2.048 |
Call Number |
UA @ lucian @ c:irua:152382 |
Serial |
5043 |
Permanent link to this record |