|
“Thickness dependence of the resistivity of platinum-group metal thin films”. Dutta S, Sankaran K, Moors K, Pourtois G, Van Elshocht S, Bommels J, Vandervorst W, Tokei Z, Adelmann C, Journal of applied physics 122, 025107 (2017). http://doi.org/10.1063/1.4992089
Abstract: We report on the thin film resistivity of several platinum-group metals (Ru, Pd, Ir, and Pt). Platinum-group thin films show comparable or lower resistivities than Cu for film thicknesses below about 5 nm due to a weaker thickness dependence of the resistivity. Based on experimentally determined mean linear distances between grain boundaries as well as ab initio calculations of the electron mean free path, the data for Ru, Ir, and Cu were modeled within the semiclassical Mayadas-Shatzkes model [Phys. Rev. B 1, 1382 (1970)] to assess the combined contributions of surface and grain boundary scattering to the resistivity. For Ru, the modeling results indicated that surface scattering was strongly dependent on the surrounding material with nearly specular scattering at interfaces with SiO2 or air but with diffuse scattering at interfaces with TaN. The dependence of the thin film resistivity on the mean free path is also discussed within the Mayadas-Shatzkes model in consideration of the experimental findings. Published by AIP Publishing.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 2.068
Times cited: 42
DOI: 10.1063/1.4992089
|
|
|
“Resistivity scaling and electron relaxation times in metallic nanowires”. Moors K, Sorée B, Tokei Z, Magnus W, Journal of applied physics 116, 063714 (2014). http://doi.org/10.1063/1.4892984
Abstract: We study the resistivity scaling in nanometer-sized metallic wires due to surface roughness and grain-boundaries, currently the main cause of electron scattering in nanoscaled interconnects. The resistivity has been obtained with the Boltzmann transport equation, adopting the relaxation time approximation of the distribution function and the effective mass approximation for the conducting electrons. The relaxation times are calculated exactly, using Fermi's golden rule, resulting in a correct relaxation time for every sub-band state contributing to the transport. In general, the relaxation time strongly depends on the sub-band state, something that remained unclear with the methods of previous work. The resistivity scaling is obtained for different roughness and grain-boundary properties, showing large differences in scaling behavior and relaxation times. Our model clearly indicates that the resistivity is dominated by grain-boundary scattering, easily surpassing the surface roughness contribution by a factor of 10. (C) 2014 AIP Publishing LLC.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.068
Times cited: 17
DOI: 10.1063/1.4892984
|
|
|
“Reliability of copper dual damascene influenced by pre-clean”. Tokei Z, Lanckmans F, van den Bosch G, Van Hove M, Maex K, Bender H, Hens S, van Landuyt J, Analysis Of Integrated Circuits , 118 (2002). http://doi.org/10.1109/IPFA.2002.1025629
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
Times cited: 5
DOI: 10.1109/IPFA.2002.1025629
|
|
|
“Modeling of edge scattering in graphene interconnects”. Contino A, Ciofi I, Wu X, Asselberghs I, Celano U, Wilson CJ, Tokei Z, Groeseneken G, Sorée B, IEEE electron device letters 39, 1085 (2018). http://doi.org/10.1109/LED.2018.2833633
Abstract: Graphene interconnects are being considered as a promising candidate for beyond CMOS applications, thanks to the intrinsic higher carrier mobility, lower aspect ratio and better reliability with respect to conventional Cu damascene interconnects. However, similarly to Cu, line edge roughness can seriously affect graphene resistance, something which must be taken into account when evaluating the related performance benefits. In this letter, we present a model for assessing the impact of edge scattering on the resistance of graphene interconnects. Our model allows the evaluation of the total mean free path in graphene lines as a function of graphene width, diffusive scattering probability and edge roughness standard deviation and autocorrelation length. We compare our model with other models from literature by benchmarking them using the same set of experimental data. We show that, as opposed to the considered models from literature, our model is capable to describe the mobility drop with scaling caused by significantly rough edges.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.048
Times cited: 1
DOI: 10.1109/LED.2018.2833633
|
|
|
“Exploring alternative metals to Cu and W for interconnects : an ab initio Insight”. Sankaran K, Clima S, Mees M, Adelmann C, Tokei Z, Pourtois G, 2014 Ieee International Interconnect Technology Conference / Advanced Metallization Conference (iitc/amc) , 193 (2014)
Abstract: The properties of alternative metals to Cu and W for interconnect applications are reviewed based on first-principles simulations and benchmarked in terms of intrinsic bulk resistivity and electromigration.
Keywords: P1 Proceeding; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|
|
“Electron relaxation times and resistivity in metallic nanowires due to tilted grain boundary planes”. Moors K, Soree B, Tokei Z, Magnus W, On Ultimate Integration On Silicon (eurosoi-ulis) , 201 (2015)
Abstract: We calculate the resistivity contribution of tilted grain boundaries with varying parameters in sub-10nm diameter metallic nanowires. The results have been obtained with the Boltzmann transport equation and Fermi's golden rule, retrieving correct state-dependent relaxation times. The standard approximation schemes for the relaxation times are shown to fail when grain boundary tilt is considered. Grain boundaries tilted under the same angle or randomly tilted induce a resistivity decrease.
Keywords: P1 Proceeding; Condensed Matter Theory (CMT)
|
|
|
“Alternative Metals: from ab initio Screening to Calibrated Narrow Line Models”. Adelmann C, Sankaran K, Dutta S, Gupta A, Kundu S, Jamieson G, Moors K, Pinna N, Ciofi I, Van Elshocht S, Bommels J, Boccardi G, Wilson CJ, Pourtois G, Tokei Z, Proceedings of the IEEE ... International Interconnect Technology Conference
T2 –, IEEE International Interconnect Technology Conference (IITC), JUN 04-07, 2018, Santa Clara, CA , 154 (2018). http://doi.org/10.1109/IITC.2018.8456484
Abstract: We discuss the selection and assessment of alternative metals by a combination of ab initio computation of electronic properties, experimental resistivity assessments, and calibrated line resistance models. Pt-group metals as well as Nb are identified as the most promising elements, with Ru showing the best combination of material properties and process maturity. An experimental assessment of the resistivity of Ru, Ir, and Co lines down to similar to 30 nm(2) is then used to devise compact models for line and via resistance that can be compared to Cu predictions. The main advantage of alternative metals originates from the possibility for barrierless metallization.
Keywords: P1 Proceeding; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
DOI: 10.1109/IITC.2018.8456484
|
|
|
“Metallic ceramics for low resitivity interconnects : an ab initio insight”. Sankaran K, Moors K, Dutta S, Adelmann C, Tokei Z, Pourtois G, Proceedings of the IEEE ... International Interconnect Technology Conference
T2 –, IEEE International Interconnect Technology Conference (IITC), JUN 04-07, 2018, Santa Clara, CA , 160 (2018)
Abstract: The scalability potential of low resistivity ternary metallic alloys (MAX) as an interconnect medium has been benchmarked against copper through first-principle simulations. We report that some carbon and nitrogen MAX phases have the potential to display a reduced sensitivity of their intrinsic resistivity to scaling, while showing improved electromigration properties.
Keywords: P1 Proceeding; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|