NANOlab Center of Excellence literature database -- Query Results

	NANOlab Center of Excellence literature database Home \| Show All \| Simple Search \| Advanced Search	Login Quick Search: Field: contains: ...
	121–150 of 375 records found matching your query (RSS \| history):

Select All Deselect All

<< 1 2 3 4 5 6 7 8 9 10 11 12 13 >>

List View

Citations

Details

	Records
	Author	Faust, V.; Boon, N.; Ganigué, R.; Vlaeminck, S.E.; Udert, K.M.
	Title	Optimizing control strategies for urine nitrification : narrow pH control band enhances process stability and reduces nitrous oxide emissions			Type	A1 Journal article
	Year	2023	Publication	Frontiers in environmental science	Abbreviated Journal
	Volume	11	Issue		Pages	1275152-14
	Keywords	A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
	Abstract	Nitrification is well-suited for urine stabilization. No base dosage is required if the pH is controlled within an appropriate operating range by urine feeding, producing an ammonium-nitrate fertilizer. However, the process is highly dependent on the selected pH set-points and is susceptible to process failures such as nitrite accumulation or the growth of acid-tolerant ammonia-oxidizing bacteria. To address the need for a robust and reliable process in decentralized applications, two different strategies were tested: operating a two-position pH controller (inflow on/off) with a narrow pH control band at 6.20/6.25 (∆pH = 0.05, narrow-pH) vs. a wider pH control band at 6.00/6.50 (∆pH = 0.50, wide-pH). These variations in pH also cause variations in the chemical speciation of ammonia and nitrite and, as shown, the microbial production of nitrite. It was hypothesized that the higher fluctuations would result in greater microbial diversity and, thus, a more robust process. The diversity of nitrifiers was higher in the wide-pH reactor, while the diversity of the entire microbiome was similar in both systems. However, the wide-pH reactor was more susceptible to tested process disturbances caused by increasing pH or temperature, decreasing dissolved oxygen, or an influent stop. In addition, with an emission factor of 0.47%, the nitrous oxide (N2O) emissions from the wide-pH reactor were twice as high as the N2O emissions from the narrow-pH reactor, most likely due to the nitrite fluctuations. Based on these results, a narrow control band is recommended for pH control in urine nitrification.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	001087861500001	Publication Date	2023-10-10
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	2296-665x	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor		Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: NA
	Call Number	UA @ admin @ c:irua:199585			Serial	8909
Permanent link to this record



	Author	Scandura, G.; Eid, S.; Alnajjar, A.A.; Paul, T.; Karanikolos, G.N.; Shetty, D.; Omer, K.; Alqerem, R.; Juma, A.; Wang, H.; Arafat, H.A.; Dumee, L.F.
	Title	Photo-responsive metal-organic frameworks – design strategies and emerging applications in photocatalysis and adsorption			Type	A1 Journal article
	Year	2023	Publication	Materials Advances	Abbreviated Journal
	Volume	4	Issue	5	Pages	1258-1285
	Keywords	A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
	Abstract	Stimuli-responsive metal-organic frameworks (MOFs) are highly versatile porous materials with the ability to respond to different external stimuli, including temperature, pressure, pH, and light. The MOF properties can switch reversibly under specific light irradiation, opening the doors to various applications. This review focuses on design strategies to obtain photo-responsive MOFs, namely (i) encapsulation of photo-switchable molecules as guests in MOF porous structures, (ii) fabrication of MOF composites, (iii) post-synthesis modification, and (iv) synthesis of MOFs with photo-responsive ligands. The most recent reports from the literature are herein reviewed and analyzed in terms of material chemistry and performance. Comparisons between the different strategies are performed and future challenges are discussed. The critical aspect of the fatigue of photo-responsive MOFs applied for prolonged cycling of irradiation is also discussed.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000938241000001	Publication Date	2023-02-24
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN		ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor		Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: NA
	Call Number	UA @ admin @ c:irua:199418			Serial	8913
Permanent link to this record



	Author	Borah, R.; Kumar, A.; Samantaray, M.; Desai, A.; Tseng, F.-G.
	Title	Photothermal heating of Au nanorods and nanospheres : temperature characteristics and strength of convective forces			Type	A1 Journal article
	Year	2023	Publication	Plasmonics	Abbreviated Journal
	Volume	18	Issue	4	Pages	1449-1465
	Keywords	A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
	Abstract	The nanoscale photothermal effect and the optofluidic convection around plasmonic nanoparticles drive the application of such nanoparticles in micro-environment. In this work, heat transfer and fluid flow around Au nanospheres and nanorods in water medium under continuous and pulsed wave laser irradiance was investigated using an FEM based numerical framework. Au nanospheres of a wide range of diameter: 40 nm = Diameter (D) = 180 nm and relatively large nanorods (diameter: 50 nm) with varying aspect ratio (1 = Aspect ratio (A) = 5) and orientation (0 degrees = ? = 90 degrees, ? = 0 degrees, 90 degrees) with respect to the incident EM radiation were investigated for continuous wave (CW) and pulsed wave laser. It was found that although nanorods can attain much higher temperature than nanospheres, orientation of a nanorod is an important factor to be carefully considered in applications. In micro-scale spherical and hemispherical confinements (diameter < 14.4 p.m), the convective velocity fields around nanoparticles is in the order of 10-9 m/s, with only a weak effect of the slip or no-slip boundary condition on the confining walls. Importantly, the size of the confinement has a strong effect leading to an order of magnitude stronger convection for 14.4 p.m (diameter) spherical confinement as compared to 3.6 p.m confinement. Additionally close proximity of the nanoparticles to the confining walls strongly reduces (by an order of magnitude) the convective currents. The results reported herein provides important insights for the use of photothermal nanoparticles in microscale confined space (e.g. cellular environment) for applications such as optical tweezers, photoporation, etc.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000985445100001	Publication Date	2023-05-11
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1557-1955; 1557-1963	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	3	Times cited		Open Access	Not_Open_Access
	Notes				Approved	Most recent IF: 3; 2023 IF: 2.139
	Call Number	UA @ admin @ c:irua:197380			Serial	8914
Permanent link to this record



	Author	Hofer, C.; Mustonen, K.; Skakalova, V.; Pennycook, T.J.
	Title	Picometer-precision few-tilt ptychotomography of 2D materials			Type	A1 Journal article
	Year	2023	Publication	2D materials	Abbreviated Journal
	Volume	10	Issue	3	Pages	035029-7
	Keywords	A1 Journal article; Electron microscopy for materials research (EMAT)
	Abstract	From ripples to defects, edges and grain boundaries, the 3D atomic structure of 2D materials is critical to their properties. However the damage inflicted by conventional 3D analysis precludes its use with fragile 2D materials, particularly for the analysis of local defects. Here we dramatically increase the potential for precise local 3D atomic structure analysis of 2D materials, with both greatly improved dose efficiency and sensitivity to light elements. We demonstrate light atoms can now be located in complex 2D materials with picometer precision at doses 30 times lower than previously possible. Moreover we demonstrate this using WS2, in which the light atoms are practically invisible to conventional methods at low doses. The key advance is combining the concept of few tilt tomography with highly dose efficient ptychography in scanning transmission electron microscopy. We further demonstrate the method experimentally with the even more challenging and newly discovered 2D CuI, leveraging a new extremely high temporal resolution camera.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	001013151600001	Publication Date	2023-06-12
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	2053-1583	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	5.5	Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: 5.5; 2023 IF: 6.937
	Call Number	UA @ admin @ c:irua:197809			Serial	8915
Permanent link to this record



	Author	De Micco, V.; Amitrano, C.; Mastroleo, F.; Aronne, G.; Battistelli, A.; Carnero-Diaz, E.; De Pascale, S.; Detrell, G.; Dussap, C.-G.; Ganigué, R.; Jakobsen, Ø.M.; Poulet, L.; Van Houdt, R.; Verseux, C.; Vlaeminck, S.E.; Willaert, R.; Leys, N.
	Title	Plant and microbial science and technology as cornerstones to Bioregenerative Life Support Systems in space			Type	A1 Journal article
	Year	2023	Publication	NPJ microgravity	Abbreviated Journal
	Volume	9	Issue	1	Pages	69-12
	Keywords	A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
	Abstract	Long-term human space exploration missions require environmental control and closed Life Support Systems (LSS) capable of producing and recycling resources, thus fulfilling all the essential metabolic needs for human survival in harsh space environments, both during travel and on orbital/planetary stations. This will become increasingly necessary as missions reach farther away from Earth, thereby limiting the technical and economic feasibility of resupplying resources from Earth. Further incorporation of biological elements into state-of-the-art (mostly abiotic) LSS, leading to bioregenerative LSS (BLSS), is needed for additional resource recovery, food production, and waste treatment solutions, and to enable more self-sustainable missions to the Moon and Mars. There is a whole suite of functions crucial to sustain human presence in Low Earth Orbit (LEO) and successful settlement on Moon or Mars such as environmental control, air regeneration, waste management, water supply, food production, cabin/habitat pressurization, radiation protection, energy supply, and means for transportation, communication, and recreation. In this paper, we focus on air, water and food production, and waste management, and address some aspects of radiation protection and recreation. We briefly discuss existing knowledge, highlight open gaps, and propose possible future experiments in the short-, medium-, and long-term to achieve the targets of crewed space exploration also leading to possible benefits on Earth.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	001093834300001	Publication Date	2023-08-24
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	2373-8065	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor		Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: NA
	Call Number	UA @ admin @ c:irua:199050			Serial	8916
Permanent link to this record



	Author	Foltyn, M.; Norowski, K.; Wyszynski, M.J.; De Arruda, A.S.; Milošević, M.V.; Zgirski, M.
	Title	Probing confined vortices with a superconducting nanobridge			Type	A1 Journal article
	Year	2023	Publication	Physical review applied	Abbreviated Journal
	Volume	19	Issue	4	Pages	044073-12
	Keywords	A1 Journal article; Condensed Matter Theory (CMT)
	Abstract	We realize a superconducting nanodevice in which vortex traps in the form of an aluminum square are integrated with a Dayem nanobridge. We perform field cooling of the traps arriving to different vortex configurations, dependent on the applied magnetic field, to demonstrate that the switching current of the bridge is highly sensitive to the presence and location of vortices in the trap. Our measurements exhibit unprecedented precision and ability to detect the first and successive vortex entries into all fabricated traps, from few hundred nm to 2 mu m in size. The experimental results are corroborated by Ginzburg-Landau simulations, which reveal the subtle yet crucial changes in the density of the superconducting condensate in the vicinity of the bridge with every additional vortex entry and relocation inside the trap. An ease of integration and simplicity make our design a convenient platform for studying dynamics of vortices in strongly confining geometries, involving a promise to manipulate vortex states electronically with simultaneous in situ control and monitoring.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000980861100007	Publication Date	2023-04-24
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	2331-7019	ISBN		Additional Links	UA library record; WoS full record
	Impact Factor	4.6	Times cited		Open Access	Not_Open_Access
	Notes				Approved	Most recent IF: 4.6; 2023 IF: 4.808
	Call Number	UA @ admin @ c:irua:197356			Serial	8918
Permanent link to this record



	Author	Friedrich, T.
	Title	Quantifying atomic structures using neural networks from 4D scanning transmission electron microscopy (STEM) datasets			Type	Doctoral thesis
	Year	2023	Publication		Abbreviated Journal
	Volume		Issue		Pages	127 p.
	Keywords	Doctoral thesis; Electron microscopy for materials research (EMAT)
	Abstract	Nanoscience and nanotechnologies are of immense importance across many fields of science and for numerous practical applications. In this context, scanning transmission electron microscopy (STEM) and 4D-STEM are among the most powerful characterization methods at the atomic scale. Annular dark-field (ADF)-STEM can be used to quantify atomic structures in 3D by counting atoms based on a single projection image. In 4D-STEM a full diffraction pattern is recorded at each scan step, which enables more dose efficient imaging and the utilization of various advanced imaging modalities, which can however be complex and slow. Both, STEM and 4D-STEM suffer from noise and distortions. In the first section of this work the most important of these distortions are discussed and it is shown how image restoration with a dedicated convolutional neural network (CNN) can be beneficial for atomic structure quantifications in ADF-STEM. In the second part, a new 4D-STEM imaging method real-time-integrated-centre-of-mass (riCOM) is introduced, which is a very dose-efficient and fast algorithm that enables unprecedented live-imaging capabilities for 4D-STEM. It is based on the integrated centre-of-mass approach, but is reformulated with variable integration ranges and optional filters, which allows for a tunable contrast transfer function. This enables the imaging of light and heavy elements simultaneously at very low doses. In the third part another new 4D-STEM method, coined AIRPI (AI-assisted rapid phase imaging) is introduced, which uses a CNN to retrieve a patch of the specimen's phase image for each scan position, based on the diffraction patterns in the probe's immediate surroundings. This allows also live imaging in principle and surpasses comparable state-of-the-art algorithms in terms of resolution also at low doses. Different atomic columns can be reliably distinguished over a wide range of atomic numbers, enabling a very good image interpretability. Further, AIRPI can recover low frequency image components, which preserves thickness information. This is a unique and important feature which could make quantitative 4D-STEM feasible.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos		Publication Date
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN		ISBN		Additional Links	UA library record
	Impact Factor		Times cited		Open Access
	Notes				Approved	Most recent IF: NA
	Call Number	UA @ admin @ c:irua:196826			Serial	8919
Permanent link to this record



	Author	Zhang, K.
	Title	Revealing the correlation between titania support properties and propylphosphonic acid modification by in-depth characterization			Type	Doctoral thesis
	Year	2023	Publication		Abbreviated Journal
	Volume		Issue		Pages	XVI, 262 p.
	Keywords	Doctoral thesis; Laboratory of adsorption and catalysis (LADCA)
	Abstract	Grafting organophosphonic acids modification (PAs) on metal oxides has shown to be a flexible technology to tune the surface properties of metal oxides for various applications. Nevertheless, there are still puzzles that need to be addressed, such as the correlations between metal oxides properties (types of surface reactive sites) and the modification (modification degree), the correlations between metal oxides properties and the properties of modified surfaces. Moreover, the currently used liquid-phase method for the grafting has associated impeding effects of solvent on tailoring the modification degrees, and also causes the formation of metal phosphonate side products. The solid-phase method can induce the unwanted changes in crystal phase of supports. Based on these questions, the three titania supports with divergent surface properties were selected as the metal oxides supports investigated, propylphosphonic acid (3PA) modification was carried out under the same synthesis conditions: four different concentrations, two solvents (water or toluene), and one reaction time (4 h) and temperature (90 ). MeOH chemisorption was introduced to probe the surface (un)reactive sites for 3PA modification. On the other hand, MeOH chemisorption and inverse gas chromatography (IGC) were combined to characterize the changes in surface polarity and acidic properties induced by the modification. Next, a solid-phase method, manual grinding, was proposed to graft 3PA on titania, avoiding the impeding effects of solvent on improving modification degree and the formation of the titania phosphonate side products, as well as preserving the crystal phase. The results indicate that methanol chemisorption can qualitatively analyze the surface active sites that are consumed by 3PA modification, its chemisorption capacity shows the consistent trend with the maximum modification degree, hereby revealing the kinds of interactions that are important in controlling surface coverage. Titania supports is found to play an important role in changes in surface polarity and acidic properties by charactering the three modified titania samples at a similar modification degree using the methanol chemisorption coupled with in-situ infrared and thermogravimetric-mass spectrometer, and the IGC. Moreover, IGC provides additional information about the changes in binding modes. Furthermore, grafting 3PA modification on titania was achieved by manual grinding. Compared to the liquid-phase method, the maximum modification degree obtained by the manual grinding is 25 % higher while using 83.3 % or 75.0% lower amounts of expensive 3PA and limiting the formation of titania phosphonate side products. Compared to the reactive milling method, the proposed manual grinding method preserves the crystal phase(s) of titania.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos		Publication Date
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN		ISBN		Additional Links	UA library record
	Impact Factor		Times cited		Open Access
	Notes				Approved	Most recent IF: NA
	Call Number	UA @ admin @ c:irua:198726			Serial	8924
Permanent link to this record



	Author	Derks, K.
	Title	Scanning Michael Sweerts and Michaelina Wautier : uncovering the working methods of 17th-century Brussels artists by means of MA-XRF examination			Type	Doctoral thesis
	Year	2023	Publication		Abbreviated Journal
	Volume		Issue		Pages	634 p.
	Keywords	Doctoral thesis; Art; Antwerp Cultural Heritage Sciences (ARCHES); Antwerp X-ray Imaging and Spectroscopy (AXIS)
	Abstract	This dissertation focuses on the materials and techniques used by the Brussels artists Michael Sweerts (1618-1664) and Michaelina Wautier (1614-1689). It tries to answer the following research questions: 1.Did 17th-century Brussels-based artists use idiosyncratic painting materials and techniques, and can their work be distinguished from paintings created in other artistic centers based on these materials and techniques? 2.How did Sweerts and Wautier influence each other’s work? In order to answer the research questions, a selection of relevant and representative paintings from Sweerts’ and Wautier’s oeuvre has been studied with MA-XRF scanning and microscopic examination. The results are discussed in volume 2 of this dissertation, and form the basis upon which the chapters in volume 1 are built. MA-XRF scanning is a non-destructive imaging technique based on the technique of X-ray fluorescence (XRF). The technique allows for the collection of elemental information about the materials present in a work of art. The work presented in this dissertation has shed more light on the working methods of Sweerts and Wautier. It has shown they both showed an openness and willingness to continue learning and developing as an artist. Wautier did not feel constrained to work only in one genre and apparently carried on developing her skills throughout her career, as evidenced by Flower Garland with Butterfly. She might have trained with a specialized artist to master their idiosyncratic working methods and this diverse genre. This suggests that Wautier had an interest in art education. Sweerts too had a passion for art education: he was involved in the drawing academy of Camillo Pamphilj in Rome, and later established his own academy for life drawing in Brussels. Sweerts’ work clearly shows the influence of his Italian contemporaries. Whilst living in Rome, he adapted his working methods to local customs such as working on brightly colored grounds. Wautier’s oeuvre shows that she was open to explore different genres and that she took inspiration from her contemporaries, including Theodoor van Loon and Daniël Seghers. In doing so, she furthered the development of different genres as she added original elements to her compositions. It is the conclusion of this dissertation that Michaelina Wautier can thus be considered one of the innovative artists of mid-17th-century Flemish painting, who inspired other artists in the Low Countries, including Michael Sweerts.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos		Publication Date
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN		ISBN		Additional Links	UA library record
	Impact Factor		Times cited		Open Access
	Notes				Approved	Most recent IF: NA
	Call Number	UA @ admin @ c:irua:197182			Serial	8927
Permanent link to this record



	Author	Gielis, J.
	Title	Simon Stevin as a central figure in the development of abstract algebra and generic programming			Type	A1 Journal article
	Year	2023	Publication	Symmetry : culture and science	Abbreviated Journal
	Volume	34	Issue	2	Pages	155-168
	Keywords	A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
	Abstract	Simon Stevin (1548-1620) is mainly known for the decimal system and his Clootkrans proof. His influence is also profound in infinitesimal calculus, mechanics, and even in abstract algebra and today’s conception of polynomials, algorithms, and generic programming. Here we review his influence as assessed in generic programming. According to Dr. Stepanov, one of the most influential researchers in generic programming, Stevin’s work on polynomials can be regarded as the essence of generic programming: an algorithm from one domain can be applied in another similar domain.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	001068714100003	Publication Date	2023-07-11
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	0865-4824	ISBN		Additional Links	UA library record; WoS full record
	Impact Factor		Times cited		Open Access	Not_Open_Access: Available from 08.02.2024
	Notes				Approved	Most recent IF: NA
	Call Number	UA @ admin @ c:irua:198000			Serial	8929
Permanent link to this record



	Author	Zhang, K.; Wang, J.; Ninakanti, R.; Verbruggen, S.W.
	Title	Solvothermal synthesis of mesoporous TiO2 with tunable surface area, crystal size and surface hydroxylation for efficient photocatalytic acetaldehyde degradation			Type	A1 Journal article
	Year	2023	Publication	Chemical engineering journal	Abbreviated Journal
	Volume	474	Issue		Pages	145188-14
	Keywords	A1 Journal article; Engineering sciences. Technology; Laboratory of adsorption and catalysis (LADCA)
	Abstract	Photocatalytic acetaldehyde degradation exhibits satisfactory performance only at relatively low acetaldehyde flow rates, predominately below 10 × 10-3 mL/min, leaving ample room for improvement. Therefore, it is necessary to prepare more efficient photocatalysts for acetaldehyde degradation. Moreover, the impact of the interaction strength between the titania surface and surface water on the photocatalytic acetaldehyde efficiency is poorly understood. To address these issues, in this work a series of (0 0 1)-faceted anatase titania samples with various surface properties and structures were synthesized via a solvothermal method and tested at high acetaldehyde flow rates under UV light irradiation. With increasing solvothermal time, the pore volume, surface area, and the abundance of surface OH groups all increased, while the crystallite size decreased. These were all identified to be beneficial to promote the degradation performance. When the solvothermal temperature was 180 ℃ and the reaction time was 5 h, the prepared sample displayed the most efficient performance at 19.25× 10-3 mL/min of acetaldehyde (conversion of (74 ± 1)% versus (29 ± 1)% for P25), and achieved a 100 % conversion at 16 × 10-3 mL/min. A weaker interaction strength between surface water and the titania surface was found to improve the acetaldehyde adsorption capacity, thereby promoting the acetaldehyde degradation efficiency. The stability of the best performing sample was tested over 48 h, demonstrating a highly stable performance with no signs of deactivation. Even at a relative humidity of 30 %, the acetaldehyde conversion retains 82% of its efficiency in a dry atmosphere, highlighting its potential in practical applications.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	001144928800001	Publication Date	2023-08-05
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1385-8947; 1873-3212	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	15.1	Times cited		Open Access	Not_Open_Access: Available from 06.02.2024
	Notes				Approved	Most recent IF: 15.1; 2023 IF: 6.216
	Call Number	UA @ admin @ c:irua:198652			Serial	8933
Permanent link to this record



	Author	Bellizotti Souza, J.C.; Vizarim, N.P.; Reichhardt, C.J.O.; Reichhardt, C.; Venegas, P.A.
	Title	Spontaneous skyrmion conformal lattice and transverse motion during dc and ac compression			Type	A1 Journal article
	Year	2023	Publication	New journal of physics	Abbreviated Journal
	Volume	25	Issue	5	Pages	053020-15
	Keywords	A1 Journal article; Condensed Matter Theory (CMT)
	Abstract	We use atomistic-based simulations to investigate the behavior of ferromagnetic skyrmions being continuously compressed against a rigid wall under dc and ac drives. The compressed skyrmions can be annihilated close to the wall and form a conformal crystal with both a size and a density gradient, making it distinct from conformal crystals observed previously for superconducting vortices and colloidal particles. For both dc and ac driving, the skyrmions can move transverse to the compression direction due to a combination of density and size gradients. Forces in the compression direction are converted by the Magnus force into transverse motion. Under ac driving, the amount of skyrmion annihilation is reduced and we find a skyrmion Magnus ratchet pump. We also observe shear banding in which skyrmions near the wall move up to twice as fast as skyrmions further from the wall. When we vary the magnitude of the applied drive, we find a critical current above which the skyrmions are completely annihilated during a time scale that depends on the magnitude of the drive. By varying the magnetic parameters, we find that the transverse motion is strongly dependent on the skyrmion size. Smaller skyrmions are more rigid, which interferes with the size gradient and destroys the transverse motion. We also confirm the role of the size gradient by comparing our atomistic simulations with a particle-based model, where we find that the transverse motion is only transient. Our results are relevant for applications where skyrmions encounter repulsive magnetic walls, domain walls, or interfaces.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000994003200001	Publication Date	2023-05-11
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1367-2630	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	3.3	Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: 3.3; 2023 IF: 3.786
	Call Number	UA @ admin @ c:irua:197365			Serial	8934
Permanent link to this record



	Author	Li, Q.; Niklas, K.J.J.; Niinemets, U.; Zhang, L.; Yu, K.; Gielis, J.; Gao, J.; Shi, P.
	Title	Stomatal shape described by a superellipse in four Magnoliaceae species			Type	A1 Journal article
	Year	2023	Publication	Botany letters	Abbreviated Journal
	Volume		Issue		Pages	1-9
	Keywords	A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
	Abstract	Stomata are essential for the exchange of water vapour and atmospheric gases between vascular plants and their external environments. The stomatal geometries of many plants appear to be elliptical. However, prior studies have not tested whether this is a mathematical reality, particularly since many natural shapes that appear to be ellipses are superellipses with greater or smaller edge curvature than predicted for an ellipse. Compared with the ellipse equation, the superellipse equation includes an additional parameter that allows generation of a larger range of shapes. We randomly selected 240 stomata from each of four Magnoliaceae species to test whether the stomatal geometries are superellipses or ellipses. The stomatal geometries for most stomata (943/960) were found to be described better using the superellipse equation. The traditional “elliptical stomata hypothesis” resulted in an underestimation of the area of stomata, whereas the superellipse equation accurately predicted stomatal area. This finding has important implications for the estimation of stomatal area in studies looking at stomatal shape, geometry, and function.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	001024190300001	Publication Date	2023-07-12
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	2381-8107; 2381-8115	ISBN		Additional Links	UA library record; WoS full record
	Impact Factor	1.5	Times cited		Open Access	Not_Open_Access: Available from 12.01.2024
	Notes				Approved	Most recent IF: 1.5; 2023 IF: NA
	Call Number	UA @ admin @ c:irua:197847			Serial	8935
Permanent link to this record



	Author	Sevik, C.; Bekaert, J.; Milošević, M.V.
	Title	Superconductivity in functionalized niobium-carbide MXenes			Type	A1 Journal article
	Year	2023	Publication	Nanoscale	Abbreviated Journal
	Volume	15	Issue	19	Pages	8792-8799
	Keywords	A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT)
	Abstract	We detail the effects of Cl and S functionalization on the superconducting properties of layered (bulk) and monolayer niobium carbide (Nb2C) MXene crystals, based on first-principles calculations combined with Eliashberg theory. For bulk layered Nb2CCl2, the calculated superconducting transition temperature (T-c) is in very good agreement with the recently measured value of 6 K. We show that T-c is enhanced to 10 K for monolayer Nb2CCl2, due to an increase in the density of states at the Fermi level, and the corresponding electron-phonon coupling. We further demonstrate feasible gate- and strain-induced enhancements of T-c for both bulk-layered and monolayer Nb2CCl2 crystals, resulting in T-c values of around 38 K. In the S-functionalized Nb2CCl2 crystals, our calculations reveal the importance of phonon softening in understanding their superconducting properties. Finally, we predict that Nb3C2S2 in bulk-layered and monolayer forms is also superconducting, with a T-c of around 28 K. Considering that Nb2C is not superconducting in pristine form, our findings promote functionalization as a pathway towards robust superconductivity in MXenes.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000976973900001	Publication Date	2023-04-11
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	2040-3364; 2040-3372	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	6.7	Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: 6.7; 2023 IF: 7.367
	Call Number	UA @ admin @ c:irua:196711			Serial	8938
Permanent link to this record



	Author	Gheysen, J.; Kashiwar, A.; Idrissi, H.; Villanova, J.; Simar, A.
	Title	Suppressing hydrogen blistering in a magnesium-rich healable laser powder bed fusion aluminum alloy analyzed by in-situ high resolution techniques			Type	A1 Journal article
	Year	2023	Publication	Materials & design	Abbreviated Journal
	Volume	231	Issue		Pages	112024-11
	Keywords	A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
	Abstract	Hydrogen blistering, i.e. precipitation of supersaturated hydrogen at elevated temperatures, increases porosity during heat treatments in 4xxx series Al alloys manufactured by laser powder bed fusion (LPBF), as demonstrated by 3D X-ray nano-imaging in AlSi12. This paper proposes the design of a healable Al alloy to suppress hydrogen blistering and improve the damage management. The strategy consists of solute atoms diffusing towards nano-voids and precipitating on their surface, thereby filling the damage sites. A new healable Al alloy was thus developed and successfully manufactured by LPBF. 3D X-ray nano-imaging evidenced that the addition of Mg in 4xxx series Al alloys suppresses the hydrogen blistering. This is expectedly due to Mg in solid solution which increases the hydrogen solubility in the Al matrix and due to the healing of these hydrogen pores. Moreover, a significant healing of voids smaller than 500 nm diameter is observed. In-situ heating inside transmission electron microscopy pointed out that Al matrix diffuses inside the fractured Mg2Si particles, thereby demonstrating the healing ability of the new alloy. This has opened the doors to development of new healable Al alloys manufactured by LPBF as well as to new post-treatments to tailor mechanical properties and microstructure without hydrogen blistering.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	001055174900001	Publication Date	2023-05-20
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	0264-1275; 1873-4197	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	8.4	Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: 8.4; 2023 IF: 4.364
	Call Number	UA @ admin @ c:irua:196536			Serial	8939
Permanent link to this record



	Author	Hasnat Rubel, A.
	Title	Theoretical characterization and optimization of nano-engineered superconducting scanning probe tip			Type	Doctoral thesis
	Year	2023	Publication		Abbreviated Journal
	Volume		Issue		Pages	viii, 145 p.
	Keywords	Doctoral thesis; Engineering sciences. Technology; Condensed Matter Theory (CMT)
	Abstract	Using state-of-the-art simulation methods, we optimized the performance of nanoscale superconducting scanning probe tips for advanced spatial imaging of magnetic fields. The systematic studies of the tips’ static properties as a function of the tilted magnetic field, geometric parameters, and material parameters were carried out. The sensitivity of different superconducting quantum interference devices (SQUIDs) to the magnetic field emanating from the magnetic nanoparticle, where the location of a magnetic nanoparticle is considered below the primary loop's center, was examined as a function of the primary and secondary loop dimensions. The main objective of the research was to characterize and optimize the performance of a nano-sized SQUID-on-tip (SOT) device. Optimal SOT sensitivity was sought, for different loop sizes, arm linewidth, and lead dimensions. Moreover, we revealed that a constriction in the loop arms of the SOT can substantially improve the sensitivity of the device. Finally, the properties of the theta-SOT device were examined in the presence of in-plane and out-of-plane magnetic field components, enabling nanoscale imaging of 3D distributions of the magnetic field. Altogether, the obtained results deliver an engineering solution for the optimum performance of the SOT device in desired conditions.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos		Publication Date
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN		ISBN		Additional Links	UA library record
	Impact Factor		Times cited		Open Access
	Notes				Approved	Most recent IF: NA
	Call Number	UA @ admin @ c:irua:199494			Serial	8942
Permanent link to this record



	Author	Zuniga-Puelles, E.; Levytskyi, V.; Özden, A.; Guerel, T.; Bulut, N.; Himcinschi, C.; Sevik, C.; Kortus, J.; Gumeniuk, R.
	Title	Thermoelectric properties and scattering mechanisms in natural PbS			Type	A1 Journal article
	Year	2023	Publication	Physical review B	Abbreviated Journal
	Volume	107	Issue	19	Pages	195203-195215
	Keywords	A1 Journal article; Condensed Matter Theory (CMT)
	Abstract	X-ray diffraction and energy dispersive x-ray spectroscopic analyses showed a natural galena (PbS) crystal from Freiberg in Saxony (Germany) to be a single phase specimen [rock salt (NaCl) structure type, space group Fm3m, a = 5.932(1) angstrom] with stoichiometric composition and an enhanced dislocation density (8 approximate to 1011 cm-2). The latter parameter leads to an increase of the electrical resistivity in the high-temperature regime, as well as to the appearance of phonon resonance with a characteristic frequency coPR = 3.8(1) THz. Being in the same range (i.e., 3-5.5 THz) with the sulfur optical modes of highest group velocities, it results in a drastic reduction (by similar to 75%) of thermal conductivity (K) at lower temperatures (i.e., < 100 K), as well as in the appearance of a characteristic minimum in K at T approximate to 30 K. Furthermore, the studied galena is characterized by phonon-drag behavior and by temperature dependent switch of the charge carrier scattering mechanism regime (i.e., scattering on dislocations for T < 100 K, on acoustic phonons for 100 K < T < 170 K and on both acoustic and optical phonons for 170 K < T < 300 K). The combined theoretical calculation and optical spectroscopic study confirm this mineral to be a direct gap degenerate semiconductor. The possible origins of the second-order Raman spectrum are discussed.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	001009980400008	Publication Date	2023-05-30
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	2469-9969; 2469-9950	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	3.7	Times cited		Open Access	Not_Open_Access
	Notes				Approved	Most recent IF: 3.7; 2023 IF: 3.836
	Call Number	UA @ admin @ c:irua:197808			Serial	8943
Permanent link to this record



	Author	Monico, L.; d'Acapito, F.; Cotte, M.; Janssens, K.; Romani, A.; Ricci, G.; Miliani, C.; Cartechini, L.
	Title	Total electron yield (TEY) detection mode Cr K-edge XANES spectroscopy as a direct method to probe the composition of the surface of darkened chrome yellow (PbCr1-xSxO4) and potassium chromate paints			Type	A1 Journal article
	Year	2023	Publication	Nuclear instruments and methods in physics research: B: beam interactions with materials and atoms	Abbreviated Journal
	Volume	539	Issue		Pages	141-147
	Keywords	A1 Journal article; Engineering sciences. Technology; Antwerp X-ray Imaging and Spectroscopy (AXIS)
	Abstract	The darkening of chromate-pigments, including chrome yellows (PbCr1-xSxO4), is a surface phenomenon affecting late 19th-early 20th c. paintings, such as those by Van Gogh. Exploring analytical strategies that contribute to a deep understanding of darkening is therefore significant for the long-term conservation of unique masterpieces. Here, we examined the capabilities of Cr K-edge XANES spectroscopy collected at the same time in X-ray fluorescence yield (XFY) and total electron yield (TEY) detection modes to selectively study the surface composition of darkened oil paint mock-ups composed of chrome yellow (PbCr0.2S0.8O4) or potassium chromate. By discussing advantages and drawbacks in using XFY/TEY modes in relation to XFY & mu;-XANES analysis from sectioned samples, we aim at assessing if TEY-XANES spectroscopy: (i) is a selective surface method to determine the abundance of different Cr-species from paint fragments; (ii) can contribute to optimize the analytical strategy by limiting time consuming sample preparation procedures; (iii) can decrease the probability of radiation damage.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	001041485400001	Publication Date	2023-04-10
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	0168-583x	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	1.3	Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: 1.3; 2023 IF: 1.109
	Call Number	UA @ admin @ c:irua:198427			Serial	8944
Permanent link to this record



	Author	Ortega Saez, N.; Arno, R.; Marchetti, A.; Cauberghs, S.; Janssens, K.; Van der Snickt, G.; Al-Emam, E.
	Title	Towards a novel strategy for soot removal from water-soluble materials : the synergetic effect of hydrogels and cyclomethicone on gelatine emulsion-based photographs			Type	A1 Journal article
	Year	2023	Publication	Heritage science	Abbreviated Journal
	Volume	11	Issue	1	Pages	78-17
	Keywords	A1 Journal article; Engineering sciences. Technology; Art; Antwerp Cultural Heritage Sciences (ARCHES); Antwerp X-ray Imaging and Spectroscopy (AXIS)
	Abstract	Gels are a popular cleaning method for paper conservators and a lot of research has been done concerning gel cleaning of paper objects over the last 15 years. Despite the close interconnection between the conservation fields of paper and photographic material, research on using gels for cleaning photographs is very scarce. However, gels can provide an excellent cleaning method for photographic material. Cleaning silver gelatine prints with aqueous solvents is very complex due to the hydrophilic properties and fragility of the gelatine layer which makes mechanical cleaning difficult. The properties of gels ensure better control over the flow and evaporation of the solvent, facilitating the cleaning process. This study is the first insight into the viability of using gellan gum gel and polyvinyl acetate-borax (PVAc-borax) gel to clean contaminants from the surface of silver gelatine photographs. It is based on self-made samples that were artificially aged and contaminated with soot. Water, ethanol (EtOH), and Kodak Photo-flo were studied as solvents to remove the soot from the silver gelatine-based prints. These solvents were loaded into the aforementioned gels and applied to the samples in two different methods. These gel cleaning methods were subsequently compared with traditional cleaning methods. In addition, the usage of cyclomethicone D4 as a protective mask for the gelatine layer was studied. Measuring methods used to evaluate the cleaning were visual comparison, microscopic observation, and densitometry. ATR-FTIR measurements were also conducted to investigate potential side-effects of the cleaning methods on the prints, such as unwanted chemical transformations or the presence of gel residues after the treatments. Most of the gel cleaning methods within this study proved to be inadequate, with the exception of the gellan gum gel loaded with 30% EtOH. It was used as a granulated gel applied mechanically on a print saturated with cyclomethicone (octamethylcyclotetrasiloxane D4). Cyclomethicone proved to be a very effective protective barrier for the water-sensitive gelatine layer with minimal reduction in cleaning effectiveness.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000970139500001	Publication Date	2023-04-18
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	2050-7445	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	2.5	Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: 2.5; 2023 IF: NA
	Call Number	UA @ admin @ c:irua:196445			Serial	8945
Permanent link to this record



	Author	Detamornrat, U.; Parrilla, M.; Domínguez-Robles, J.; Anjani, Q.K.; Larrañeta, E.; De Wael, K.; Donnelly, R.F.
	Title	Transdermal on-demand drug delivery based on an iontophoretic hollow microneedle array system			Type	A1 Journal article
	Year	2023	Publication	Lab on a chip	Abbreviated Journal
	Volume	23	Issue	9	Pages	2304-2315
	Keywords	A1 Journal article; Engineering sciences. Technology; Antwerp Electrochemical and Analytical Sciences Lab (A-Sense Lab)
	Abstract	Transdermal drug delivery has emerged as an alternative administration route for therapeutic drugs, overcoming current issues in oral and parenteral administration. However, this technology is hindered by the low permeability of the stratum corneum of the skin. In this work, we develop a synergic combination of two enhancing technologies to contribute to an improved and on-demand drug delivery through an iontophoretic system coupled with hollow microneedles (HMNs). For the first time, a polymeric HMN array coupled with integrated iontophoresis for the delivery of charged molecules and macromolecules (e.g. proteins) is devised. To prove the concept, methylene blue, fluorescein sodium, lidocaine hydrochloride, and bovine serum albumin-fluorescein isothiocyanate conjugate (BSA-FITC) were first tested in an in vitro setup using 1.5% agarose gel model. Subsequently, the ex vivo drug permeation study using a Franz diffusion cell was conducted, exhibiting a 61-fold, 43-fold, 54-fold, and 17-fold increment of the permeation of methylene blue, fluorescein sodium, lidocaine hydrochloride, and BSA-FITC, respectively, during the application of 1 mA cm(-2) current for 6 h. Moreover, the total amount of drug delivered (i.e. in the skin and receptor compartment) was analysed to untangle the different delivery profiles according to the types of molecule. Finally, the integration of the anode and cathode into an iontophoretic hollow microneedle array system (IHMAS) offers the full miniaturisation of the concept. Overall, the IHMAS device provides a versatile wearable technology for transdermal on-demand drug delivery that can improve the administration of personalised doses, and potentially enhance precision medicine.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000971513000001	Publication Date	2023-04-18
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1473-0197	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	6.1	Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: 6.1; 2023 IF: 6.045
	Call Number	UA @ admin @ c:irua:195781			Serial	8946
Permanent link to this record



	Author	Soenen, M.; Milošević, M.V.
	Title	Tunable magnon topology in monolayer CrI₃ under external stimuli			Type	A1 Journal article
	Year	2023	Publication	Physical review materials	Abbreviated Journal
	Volume	7	Issue	8	Pages	084402-84409
	Keywords	A1 Journal article; Condensed Matter Theory (CMT)
	Abstract	Two-dimensional (2D) honeycomb ferromagnets, such as monolayer chromium trihalides, are predicted to behave as topological magnon insulators, characterized by an insulating bulk and topologically protected edge states, giving rise to a thermal magnon Hall effect. Here we report the behavior of the topological magnons in monolayer CrI3 under external stimuli, including biaxial and uniaxial strain, electric gating, as well as in-plane and out-of-plane magnetic field, revealing that one can thereby tailor the magnetic states as well as the size and the topology of the magnonic bandgap. These findings broaden the perspective of using 2D magnetic materials to design topological magnonic devices.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	001052941600003	Publication Date	2023-08-08
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	2475-9953	ISBN		Additional Links	UA library record; WoS full record
	Impact Factor	3.4	Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: 3.4; 2023 IF: NA
	Call Number	UA @ admin @ c:irua:199201			Serial	8947
Permanent link to this record



	Author	Broers, F.T.H.; Janssens, K.; Weker, J.N.; Webb, S.M.; Mehta, A.; Meirer, F.; Keune, K.
	Title	Two pathways for the degradation of orpiment pigment (As₂S₃) found in paintings			Type	A1 Journal article
	Year	2023	Publication	Journal of the American Chemical Society	Abbreviated Journal
	Volume	145	Issue	16	Pages	8847-8859
	Keywords	A1 Journal article; Antwerp X-ray Imaging and Spectroscopy (AXIS)
	Abstract	Paintings are complex objects containing many different chemical compounds that can react over time. The degradation of arsenic sulfide pigments causes optical changes in paintings. The main degradation product was thought to be white arsenolite (As2O3), but previous research also showed the abundant presence of As(V) species. In this study, we investigate the influence of the presence of a medium on the degradation mechanism of orpiment (As2S3) using synchrotron radiation (SR)-based tomographic transmission X-ray microscopy, SR-based micro-X-ray fluorescence, and Xray absorption near edge structure spectroscopy. Upon direct illumination of dry orpiment powder using UV-visible light, only the formation of As2O3 was observed. When As2S3 was surrounded by a medium and illuminated, As2O3 was only observed in the area directly exposed to light, while As(V) degradation species were found elsewhere in the medium. Without accelerated artificial light aging, As(V)(aq) species are formed and migrate throughout the medium within weeks after preparation. In both scenarios, the As(V) species form via intermediate As(III)(aq) species and the presence of a medium is necessary. As(V)(aq) species can react with available cations to form insoluble metal arsenates, which induces stress within the paint layers (leading to, e.g., cracks and delamination) or can lead to a visual change of the image of the painting.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000974346900001	Publication Date	2023-04-14
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	0002-7863	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	15	Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: 15; 2023 IF: 13.858
	Call Number	UA @ admin @ c:irua:196762			Serial	8948
Permanent link to this record



	Author	Reyntjens, P.; Van de Put, M.; Vandenberghe, W.G.; Sorée, B.
	Title	Ultrascaled graphene-capped interconnects : a quantum mechanical study			Type	P1 Proceeding
	Year	2023	Publication	Proceedings of the IEEE ... International Interconnect Technology Conference T2 – IEEE International Interconnect Technology Conference (IITC) / IEEE, Materials for Advanced Metallization Conference (MAM), MAY 22-25, 2023, Dresden, Germany	Abbreviated Journal
	Volume		Issue		Pages	1-3
	Keywords	P1 Proceeding; Condensed Matter Theory (CMT)
	Abstract	In this theoretical study, we assess the impact of a graphene capping layer on the resistivity of defective, extremely scaled interconnects. We investigate the effect of graphene capping on the electronic transport in ultrascaled interconnects, in the presence of grain boundary defects in the metal layer. We compare the results obtained using our quantum mechanical model to a simple parallel-conductor model and find that the parallel-conductor model does not capture the effect of the graphene cap correctly. At 0.5 nm metal thickness, the parallel-conductor model underestimates the conductivity by 3.0% to 4.0% for single-sided and double sided graphene capping, respectively.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	001027381700006	Publication Date	2023-06-24
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	979-83-503-1097-9	ISBN		Additional Links	UA library record; WoS full record
	Impact Factor		Times cited		Open Access	Not_Open_Access
	Notes				Approved	Most recent IF: NA
	Call Number	UA @ admin @ c:irua:198343			Serial	8949
Permanent link to this record



	Author	Mazzola, F.; Hassani, H.; Amoroso, D.; Chaluvadi, S.K.; Fujii, J.; Polewczyk, V.; Rajak, P.; Koegler, M.; Ciancio, R.; Partoens, B.; Rossi, G.; Vobornik, I.; Ghosez, P.; Orgiani, P.
	Title	Unveiling the electronic structure of pseudotetragonal WO₃ thin films			Type	A1 Journal article
	Year	2023	Publication	The journal of physical chemistry letters	Abbreviated Journal
	Volume	14	Issue	32	Pages	7208-7214
	Keywords	A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT)
	Abstract	WO3 isa 5d compound that undergoes severalstructuraltransitions in its bulk form. Its versatility is well-documented,with a wide range of applications, such as flexopiezoelectricity,electrochromism, gating-induced phase transitions, and its abilityto improve the performance of Li-based batteries. The synthesis ofWO(3) thin films holds promise in stabilizing electronicphases for practical applications. However, despite its potential,the electronic structure of this material remains experimentally unexplored.Furthermore, its thermal instability limits its use in certain technologicaldevices. Here, we employ tensile strain to stabilize WO3 thin films, which we call the pseudotetragonal phase, and investigateits electronic structure using a combination of photoelectron spectroscopyand density functional theory calculations. This study reveals theFermiology of the system, notably identifying significant energy splittingsbetween different orbital manifolds arising from atomic distortions.These splittings, along with the system's thermal stability,offer a potential avenue for controlling inter- and intraband scatteringfor electronic applications.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	001044522400001	Publication Date	2023-08-08
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	1948-7185	ISBN		Additional Links	UA library record; WoS full record
	Impact Factor	5.7	Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: 5.7; 2023 IF: 9.353
	Call Number	UA @ admin @ c:irua:198391			Serial	8951
Permanent link to this record



	Author	Van Echelpoel, R.; Parrilla, M.; Sleegers, N.; Thiruvottriyur Shanmugam, S.; van Nuijs, A.L.N.; Slosse, A.; Van Durme, F.; De Wael, K.
	Title	Validated portable device for the qualitative and quantitative electrochemical detection of MDMA ready for on-site use			Type	A1 Journal article
	Year	2023	Publication	Microchemical journal	Abbreviated Journal
	Volume	190	Issue		Pages	108693-10
	Keywords	A1 Journal article; Engineering sciences. Technology; Toxicological Centre; Antwerp Electrochemical and Analytical Sciences Lab (A-Sense Lab)
	Abstract	Identifying and quantifying 3,4-methylenedioxymethamphetamine (MDMA) on-site in suspected illicit drug samples, whether it be at recreational settings or manufacturing sites, is a major challenge for law enforcement agencies (LEAs). Various analytical techniques exist to fulfil this goal, e.g. colourimetry and portable spectroscopic techniques, each having its specific limitations (e.g. low accuracy, fluorescence, no quantification) and strengths (e.g. fast, easy to use). In this work, for the first time, an electrochemical MDMA sensor is presented to become a detection tool that can realistically be used on-site. More specifically, the use of a single buffer solution and an unmodified screen-printed electrode, along with the integration of a data analysis algorithm and mobile application permits the straightforward on-site identification and quantification of MDMA in suspicious samples. Multiple studies investigating different parameters, including pH, concentration, reproducibility, temperature and binary mixture analyses, were executed. To fully understand all the occurring redox processes, liquid chromatography coupled with high-resolution mass spectrometry analysis of partially electrolyzed MDMA samples was performed unravelling oxidation of the methylenedioxy group. Validation of the methodology was executed on 15 MDMA street samples analysed by gas chromatography coupled with mass spectrometry and compared with the performance of a commercial portable Raman and Attenuated Total Reflection Fourier Transform Infrared Spectroscopy (ATR-FTIR) device. The novel methodology outperformed the spectroscopic techniques, correctly identifying all 15 street samples. Additionally, the electrochemical sensor predicted the purity of the tablets with a mean absolute error of 2.3%. Overall, this new, electrochemical detection strategy provides LEAs the rapid, low-cost, on-site detection and quantification of MDMA in suspicious samples, without requiring specialized training.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000977060400001	Publication Date	2023-03-31
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	0026-265x; 0026-265x	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	4.8	Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: 4.8; 2023 IF: 3.034
	Call Number	UA @ admin @ c:irua:195415			Serial	8952
Permanent link to this record



	Author	Wang, S.; Tian, H.; Sun, M.
	Title	Valley-polarized and enhanced transmission in graphene with a smooth strain profile			Type	A1 Journal article
	Year	2023	Publication	Journal of physics : condensed matter	Abbreviated Journal
	Volume	35	Issue	30	Pages	304002-304013
	Keywords	A1 Journal article; Condensed Matter Theory (CMT)
	Abstract	We explore the influence of strain on the valley-polarized transmission of graphene by employing the wave-function matching and the non-equilibrium Green's function technique. When the transmission is along the armchair direction, we show that the valley polarization and transmission can be improved by increasing the width of the strained region and increasing (decreasing) the extensional strain in the armchair (zigzag) direction. It is noted that the shear strain does not affect transmission and valley polarization. Furthermore, when we consider the smooth strain barrier, the valley-polarized transmission can be enhanced by increasing the smoothness of the strain barrier. We hope that our finding can shed new light on constructing graphene-based valleytronic and quantum computing devices by solely employing strain.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000977124700001	Publication Date	2023-04-11
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	0953-8984	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	2.7	Times cited		Open Access	Not_Open_Access
	Notes				Approved	Most recent IF: 2.7; 2023 IF: 2.649
	Call Number	UA @ admin @ c:irua:196718			Serial	8953
Permanent link to this record



	Author	Linard, F.J.A.; Moura, V.N.; Covaci, L.; Milošević, M.V.; Chaves, A.
	Title	Wave-packet scattering at a normal-superconductor interface in two-dimensional materials : a generalized theoretical approach			Type	A1 Journal article
	Year	2023	Publication	Physical review B	Abbreviated Journal
	Volume	107	Issue	16	Pages	165306-165309
	Keywords	A1 Journal article; Electron microscopy for materials research (EMAT); Condensed Matter Theory (CMT)
	Abstract	A wave-packet time evolution method, based on the split-operator technique, is developed to investigate the scattering of quasiparticles at a normal-superconductor interface of arbitrary profile and shape. As a practical application, we consider a system where low-energy electrons can be described as Dirac particles, which is the case for most two-dimensional materials, such as graphene and transition-metal dichalcogenides. However, the method is easily adapted for other cases such as electrons in few-layer black phosphorus or any Schrodinger quasiparticles within the effective mass approximation in semiconductors. We employ the method to revisit Andreev reflection in mono-, bi-, and trilayer graphene, where specular-and retro-reflection cases are observed for electrons scattered by a steplike superconducting region. The effect of opening a zero-gap channel across the superconducting region on the electron and hole scattering is also addressed, as an example of the versatility of the technique proposed here.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	000974675700006	Publication Date	2023-04-14
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	2469-9969; 2469-9950	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	3.7	Times cited		Open Access	OpenAccess
	Notes				Approved	Most recent IF: 3.7; 2023 IF: 3.836
	Call Number	UA @ admin @ c:irua:196709			Serial	8954
Permanent link to this record



	Author	Parrilla, M.; Detamornrat, U.; Domínguez-Robles, J.; Tunca, S.; Donnelly, R.F.; De Wael, K.
	Title	Wearable microneedle-based array patches for continuous electrochemical monitoring and drug delivery : toward a closed-loop system for methotrexate treatment			Type	A1 Journal article
	Year	2023	Publication	ACS sensors	Abbreviated Journal
	Volume		Issue		Pages	acssensors.3c01381-10
	Keywords	A1 Journal article; Engineering sciences. Technology; Antwerp Electrochemical and Analytical Sciences Lab (A-Sense Lab)
	Abstract	Wearable devices based on microneedle (MN) technology have recently emerged as tools for in situ transdermal sensing or delivery in interstitial fluid (ISF). Particularly, MN-based electrochemical sensors allow the continuous monitoring of analytes in a minimally invasive manner through ISF. Exogenous small molecules found in ISF such as therapeutic drugs are ideal candidates for MN sensors due to their correlation with blood levels and their relevance for the optimal management of personalized therapies. Herein, a hollow MN array patch is modified with conductive pastes and functionalized with cross-linked chitosan to develop an MN-based voltammetric sensor for continuous monitoring of methotrexate (MTX). Interestingly, the chitosan coating avoids biofouling while enabling the adsorption of MTX at the electrode’s surface for sensitive analysis. The MN sensor exhibits excellent analytical performance in vitro with protein-enriched artificial ISF and ex vivo under a Franz diffusion cell configuration. The MN sensor shows a linear range from 25 to 400 μM, which fits within the therapeutic range of high-dose MTX treatment for cancer patients and an excellent continuous operation for more than two days. Moreover, an iontophoretic hollow MN array patch is developed with the integration of both the anode and cathode in the single MN array patch. The ex vivo characterization demonstrates the transdermal on-demand drug delivery of MTX. Overall, the combination of both MN patches represents impactful progress in closed-loop systems for therapeutic drug management in disorders such as cancer, rheumatoid arthritis, or psoriasis.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	001109702900001	Publication Date	2023-10-19
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	2379-3694	ISBN		Additional Links	UA library record; WoS full record; WoS citing articles
	Impact Factor	8.9	Times cited		Open Access	Not_Open_Access: Available from 19.04.2024
	Notes				Approved	Most recent IF: 8.9; 2023 IF: NA
	Call Number	UA @ admin @ c:irua:200074			Serial	8956
Permanent link to this record



	Author	Duran, T.A.; Yayak, Y.O.; Aydin, H.; Peeters, F.M.; Yagmurcukardes, M.
	Title	A perspective on the state-of-the-art functionalized 2D materials			Type	A1 Journal article
	Year	2023	Publication	Journal of applied physics	Abbreviated Journal
	Volume	134	Issue	12	Pages	120901-120929
	Keywords	A1 Journal article; Condensed Matter Theory (CMT)
	Abstract	Two-dimensional (2D) ultra-thin materials are more crucial than their bulk counterparts for the covalent functionalization of their surface owing to atomic thinness, large surface-to-volume ratio, and high reactivity of surface atoms having unoccupied orbitals. Since the surface of a 2D material is composed of atoms having unoccupied orbitals, covalent functionalization enables one to improve or precisely modify the properties of the ultra-thin materials. Chemical functionalization of 2D materials not only modifies their intrinsic properties but also makes them adapted for nanotechnology applications. Such engineered materials have been used in many different applications with their improved properties. In the present Perspective, we begin with a brief history of functionalization followed by the introduction of functionalized 2D materials. Our Perspective is composed of the following sections: the applications areas of 2D graphene and graphene oxide crystals, transition metal dichalcogenides, and in-plane anisotropic black phosphorus, all of which have been widely used in different nanotechnology applications. Finally, our Perspectives on the future directions of applications of functionalized 2D materials are given. The present Perspective sheds light on the current progress in nanotechnological applications of engineered 2D materials through surface functionalization.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos	001087770500008	Publication Date
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	0021-8979; 1089-7550	ISBN		Additional Links	UA library record; WoS full record
	Impact Factor	3.2	Times cited		Open Access
	Notes				Approved	Most recent IF: 3.2; 2023 IF: 2.068
	Call Number	UA @ admin @ c:irua:201281			Serial	9000
Permanent link to this record



	Author	Mescia, L.; Bia, P.; Gielis, J.; Caratelli, D.
	Title	Advanced particle swarm optimization methods for electromagnetics			Type	P1 Proceeding
	Year	2023	Publication		Abbreviated Journal
	Volume		Issue		Pages	109-122 T2 - Proceedings of the 1st International
	Keywords	P1 Proceeding; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
	Abstract	Electromagnetic design problems involve optimizing multiple parameters that are nonlinearly related to objective functions. Traditional optimization techniques require significant computational resources that grow exponentially as the problem size increases. Therefore, a method that can produce good results with moderate memory and computational resources is desirable. Bioinspired optimization methods, such as particle swarm optimization (PSO), are known for their computational efficiency and are commonly used in various scientific and technological fields. In this article we explore the potential of advanced PSO-based algorithms to tackle challenging electromagnetic design and analysis problems faced in real-life applications. It provides a detailed comparison between conventional PSO and its quantum-inspired version regarding accuracy and computational costs. Additionally, theoretical insights on convergence issues and sensitivity analysis on parameters influencing the stochastic process are reported. The utilization of a novel quantum PSO-based algorithm in advanced scenarios, such as reconfigurable and shaped lens antenna synthesis, is illustrated. The hybrid modeling approach, based on the unified geometrical description enabled by the Gielis Transformation, is applied in combination with a suitable quantum PSO-based algorithm, along with a geometrical tube tracing and physical optics technique for solving the inverse problem aimed at identifying the geometrical parameters that yield optimal antenna performance.
	Address
	Corporate Author				Thesis
	Publisher		Place of Publication		Editor
	Language		Wos		Publication Date	2023-11-29
	Series Editor		Series Title		Abbreviated Series Title
	Series Volume		Series Issue		Edition
	ISSN	978-90-833839-0-3	ISBN		Additional Links	UA library record
	Impact Factor		Times cited		Open Access
	Notes				Approved	Most recent IF: NA
	Call Number	UA @ admin @ c:irua:201048			Serial	9002
Permanent link to this record