|
“Quantifying Strain and Dislocation Density at Nanocube Interfaces after Assembly and Epitaxy”. Agrawal H, Patra BK, Altantzis T, De Backer A, Garnett EC, Acs Applied Materials &, Interfaces 12, 8788 (2020). http://doi.org/10.1021/acsami.9b17779
Abstract: Nanoparticle self-assembly and epitaxy are utilized extensively to make 1D and 2D structures with complex shapes. High-resolution transmission electron microscopy (HRTEM) has shown that single-crystalline interfaces can form, but little is known about the strain and dislocations at these interfaces. Such information is critically important for applications: drastically reducing
dislocation density was the key breakthrough enabling widespread implementation of light-emitting diodes, while strain engineering has been fundamental to modern high-performance transistors, solar cells, and thermoelectrics. In this work, the interfacial defect and strain formation after selfassembly and room temperature epitaxy of 7 nm Pd nanocubes capped with polyvinylpyrrolidone (PVP) is examined. It is observed that, during ligand removal, the cubes move over large distances on the substrate, leading to both spontaneous self-assembly and epitaxy to form single crystals. Subsequently, atomically resolved images are used to quantify the strain and dislocation density at the epitaxial interfaces between cubes with different lateral and angular misorientations. It is shown that dislocation- and strain-free interfaces form when the nanocubes align parallel to each other. Angular misalignment between adjacent cubes does not necessarily lead to grain boundaries but does cause dislocations, with higher densities associated with larger rotations.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Applied Electrochemistry & Catalysis (ELCAT)
Impact Factor: 9.5
DOI: 10.1021/acsami.9b17779
|
|
|
“Direct correlation of nanoscale morphology and device performance to study photocurrent generation in donor-enriched phases of polymer solar cells”. Ben Dkhil S, Perkhun P, Luo C, Mueller D, Alkarsifi R, Barulina E, Quiroz YAA, Margeat O, Dubas ST, Koganezawa T, Kuzuhara D, Yoshimoto N, Caddeo C, Mattoni A, Zimmermann B, Wuerfel U, Pfannmöller M, Bals S, Ackermann J, Videlot-Ackermann C, Acs Applied Materials &, Interfaces 12, 28404 (2020). http://doi.org/10.1021/ACSAMI.0C05884
Abstract: The nanoscale morphology of polymer blends is a key parameter to reach high efficiency in bulk heterojunction solar cells. Thereby, research typically focusing on optimal blend morphologies while studying nonoptimized blends may give insight into blend designs that can prove more robust against morphology defects. Here, we focus on the direct correlation of morphology and device performance of thieno[3,4-b]-thiophene-alt-benzodithiophene (PTB7):[6,6]phenyl C-71 butyric acid methyl ester (PC71BM) bulk heterojunction (BHJ) blends processed without additives in different donor/acceptor weight ratios. We show that while blends of a 1:1.5 ratio are composed of large donor-enriched and fullerene domains beyond the exciton diffusion length, reducing the ratio below 1:0.5 leads to blends composed purely of polymer-enriched domains. Importantly, the photocurrent density in such blends can reach values between 45 and 60% of those reached for fully optimized blends using additives. We provide here direct visual evidence that fullerenes in the donor-enriched domains are not distributed homogeneously but fluctuate locally. To this end, we performed compositional nanoscale morphology analysis of the blend using spectroscopic imaging of low-energy-loss electrons using a transmission electron microscope. Charge transport measurement in combination with molecular dynamics simulations shows that the fullerene substructures inside the polymer phase generate efficient electron transport in the polymer-enriched phase. Furthermore, we show that the formation of densely packed regions of fullerene inside the polymer phase is driven by the PTB7:PC71BM enthalpy of mixing. The occurrence of such a nanoscale network of fullerene clusters leads to a reduction of electron trap states and thus efficient extraction of photocurrent inside the polymer domain. Suitable tuning of the polymer-acceptor interaction can thus introduce acceptor subnetworks in polymer-enriched phases, improving the tolerance for high-efficiency BHJ toward morphological defects such as donor-enriched domains exceeding the exciton diffusion length.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 9.5
Times cited: 7
DOI: 10.1021/ACSAMI.0C05884
|
|
|
“High-performance CO2-selective hybrid membranes by exploiting MOF-breathing effects”. Kertik A, Wee LH, Şentosun K, Navarro JAR, Bals S, Martens JA, Vankelecom IFJ, Acs Applied Materials &, Interfaces 12, 2952 (2020). http://doi.org/10.1021/ACSAMI.9B17820
Abstract: Conventional CO2 separation in the petrochemical industry via cryogenic distillation or amine-based absorber-stripper units is energy-intensive and environmentally unfriendly. Membrane-based gas separation technology, in contrast, has contributed significantly to the development of energy-efficient systems for processes such as natural gas purification. The implementation of commercial polymeric membranes in gas separation processes is restricted by their permeability-selectivity trade-off and by their insufficient thermal and chemical stability. Herein, we present the fabrication of a Matrimid-based membrane loaded with a breathing metal-organic framework (MOF) (NH2-MIL-53(Al)) which is capable of separating binary CO2/CH4 gas mixtures with high selectivities without sacrificing much of its CO2 permeabilities. NH2-MIL-53(Al) crystals were embedded in a polyimide (PI) matrix, and the mixed-matrix membranes (MMMs) were treated at elevated temperatures (up to 350 degrees C) in air to trigger PI cross-linking and to create PI-MOF bonds at the interface to effectively seal the grain boundary. Most importantly, the MOF transitions from its narrow-pore form to its large-pore form during this treatment, which allows the PI chains to partly penetrate the pores and cross-link with the amino functions at the pore mouth of the NH2-MIL-53(Al) and stabilizes the open-pore form of NH2-MIL-53(Al). This cross-linked MMM, with MOF pore entrances was made more selective by the anchored PI-chains and achieves outstanding CO2/CH4 selectivities. This approach provides significant advancement toward the design of selective MMMs with enhanced thermal and chemical stabilities which could also be applicable for other potential applications, such as separation of hydrocarbons (olefin/paraffin or isomers), pervaporation, and solvent-resistant nanofiltration.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 9.5
Times cited: 26
DOI: 10.1021/ACSAMI.9B17820
|
|
|
“The general case of cutting of Generalized Möbius-Listing surfaces and bodies”. Gielis J, Tavkhelidze I, 4Open 3, 7 (2020). http://doi.org/10.1051/FOPEN/2020007
Abstract: The original motivation to study Generalized Möbius-Listing GML surfaces and bodies was the observation that the solution of boundary value problems greatly depends on the domains. Since around 2010 GML’s were merged with (continuous) Gielis Transformations, which provide a unifying description of geometrical shapes, as a generalization of the Pythagorean Theorem. The resulting geometrical objects can be used for modeling a wide range of natural shapes and phenomena. The cutting of GML bodies and surfaces, with the Möbius strip as one special case, is related to the field of knots and links, and classifications were obtained for GML with cross sectional symmetry of 2, 3, 4, 5 and 6. The general case of cutting GML bodies and surfaces, in particular the number of ways of cutting, could be solved by reducing the 3D problem to planar geometry. This also unveiled a range of connections with topology, combinatorics, elasticity theory and theoretical physics.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1051/FOPEN/2020007
|
|
|
“Hematite at its thinnest limit”. Bacaksiz C, Yagmurcukardes M, Peeters FM, Milošević, MV, 2d Materials 7, 025029 (2020). http://doi.org/10.1088/2053-1583/AB6D79
Abstract: Motivated by the recent synthesis of two-dimensional alpha-Fe2O3 (Balan et al 2018 Nat. Nanotechnol. 13 602), we analyze the structural, vibrational, electronic and magnetic properties of single- and few-layer alpha-Fe2O3 compared to bulk, by ab initio and Monte-Carlo simulations. We reveal how monolayer alpha-Fe2O3 (hematene) can be distinguished from the few-layer structures, and how they all differ from bulk through observable Raman spectra. The optical spectra exhibit gradual shift of the prominent peak to higher energy, as well as additional features at lower energy when alpha-Fe2O3 is thinned down to a monolayer. Both optical and electronic properties have strong spin asymmetry, meaning that lower-energy optical and electronic activities are allowed for the single-spin state. Finally, our considerations of magnetic properties reveal that 2D hematite has anti-ferromagnetic ground state for all thicknesses, but the critical temperature for Morin transition increases with decreasing sample thickness. On all accounts, the link to available experimental data is made, and further measurements are prompted.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 5.5
Times cited: 12
DOI: 10.1088/2053-1583/AB6D79
|
|
|
Callaert C (2020) Characterization of defects, modulations and surface layers in topological insulators and structurally related compounds. 180 p
Keywords: Doctoral thesis; Electron microscopy for materials research (EMAT)
|
|
|
Vets C (2020) Growth properties of carbon nanomaterials : towards tuning for electronic applications. 130 p
Keywords: Doctoral thesis; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|
|
Pourbabak S (2020) Influence of nano and microstructural features and defects in finegrained NiTi on the thermal and mechanical reversibility of the martensitic transformation. 166 p
Keywords: Doctoral thesis; Electron microscopy for materials research (EMAT)
|
|
|
“Berry phase engineering at oxide interfaces”. Groenendijk DJ, Autieri C, van Thiel TC, Brzezicki W, Hortensius JR, Afanasiev D, Gauquelin N, Barone P, van den Bos KHW, van Aert S, Verbeeck J, Filippetti A, Picozzi S, Cuoco M, Caviglia AD, 2, 023404 (2020). http://doi.org/10.1103/PhysRevResearch.2.023404
Abstract: Three-dimensional strontium ruthenate (SrRuO3) is an itinerant ferromagnet that features Weyl points acting as sources of emergent magnetic fields, anomalous Hall conductivity, and unconventional spin dynamics. Integrating SrRuO3 in oxide heterostructures is potentially a novel route to engineer emergent electrodynamics, but its electronic band topology in the two-dimensional limit remains unknown. Here we show that ultrathin SrRuO3 exhibits spin-polarized topologically nontrivial bands at the Fermi energy. Their band anticrossings show an enhanced Berry curvature and act as competing sources of emergent magnetic fields. We control their balance by designing heterostructures with symmetric (SrTiO3/SrRuO3/SrTiO3 and SrIrO3/SrRuO3/SrIrO3) and asymmetric interfaces (SrTiO3/SrRuO3/SrIrO3). Symmetric structures exhibit an interface-tunable single-channel anomalous Hall effect, while ultrathin SrRuO3 embedded in asymmetric structures shows humplike features consistent with multiple Hall contributions. The band topology of two-dimensional SrRuO3 proposed here naturally accounts for these observations and harmonizes a large body of experimental results.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 58
DOI: 10.1103/PhysRevResearch.2.023404
|
|
|
Cautaerts N, Lamm S, Stergar E, Pakarinen J, Yang Y, Hofer C, Schnitzer R, Felfer P, Verwerft M, Delville R, Schryvers D (2020) Atom probe tomography data collection from DIN 1.4970 (15-15Ti) austenitic stainless steel irradiated with Fe ions
Abstract: This dataset comprises a large collection of atom probe tomography datasets collected from DIN 1.4970 alloy that was irradiated with Fe ions at different conditions. The DIN 1.4970 alloy is an austenitic stainless steel with 15 wt% Cr, 15 wt% Ni, a small addition of Ti. The full composition and characterization of our material can be found published elsewhere [1,2]. Some of our material was subjected to ageing heat treatments at different temperatures for different times. Small samples of our original material and aged material was irradiated at the Michigan Ion Beam Laboratory in 2017 with 4.5 MeV Fe ions up to 40 dpa at an average dose rate of 2×10−4 dpa/s. This was done at three different temperatures: 300, 450, and 600 ºC. Atom probe samples were made of the irradiated layers (approximately 1.5 micron deep) with focused ion beam and mounted on Microtip coupons. APT measurements took place on three CAMECA LEAP-HR systems located at CAES in Idaho Falls, USA (files beginning with R33), at Montanuniversität Leoben in Leoben, Austria (R21) and at Friedrich–Alexander University in Erlangen, Germany (R56).
Keywords: Dataset; Electron microscopy for materials research (EMAT)
DOI: 10.5281/ZENODO.3407832
|
|
|
Vermeiren V (2020) Chemical kinetics modeling of non-equilibrium and thermal effects in vibrationally active CO2 plasmas. 207 p
Keywords: Doctoral thesis; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|
|
Nematollahi P (2020) Density functional theory calculations for understanding gas conversion reactions on single metal atom embedded carbon-based nanocatalysts. 173 p
Keywords: Doctoral thesis; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|
|
De Jong M (2020) A highly accurate portable electrochemical sensor for cocaine : from methodology to testing in the field. 263 p
Keywords: Doctoral thesis; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
|
|
|
Bafekry A (2020) Investigation of the effects of defects and impurities on nanostructures consisting of Group IV and V elements using First-principles calculations. 126 p
Keywords: Doctoral thesis; Condensed Matter Theory (CMT)
|
|
|
Conti S (2020) Multi-band superfluidity and BEC-BCS crossover in novel ultrathin materials. 123 p
Keywords: Doctoral thesis; Sociology; History; Condensed Matter Theory (CMT)
|
|
|
Zhang H (2020) Optical diagnostics of spatiotemporal evolution characteristics of nanosecond laser-induced plasma in gases. 117 p
Keywords: Doctoral thesis; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|
|
Heijkers S (2020) Plasma chemistry modelling for CO2 and CH4 conversion in various plasma types. 316 p
Keywords: Doctoral thesis; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|
|
Eliaerts J (2020) Qualitative and quantitative determination of cocaine using mid-infrared spectroscopy and chemometrics. 184 p
Keywords: Doctoral thesis; Law; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
|
|
|
Vanherck J (2020) Spontaneous and induced magnetisation in two-dimensional and bulk Heisenberg ferromagnets : a quantum mechanical treatment. 160 p
Keywords: Doctoral thesis; Condensed Matter Theory (CMT)
|
|
|
Hendrickx M (2020) Study of the effect of cation substitution on the local structure and the properties of perovskites and Li-ion battery cathode materials. 208 p
Keywords: Doctoral thesis; Electron microscopy for materials research (EMAT)
|
|
|
Milagres de Oliveira T (2020) Three-dimensional characterisation of nanomaterials : from model-like systems to real nanostructures. 230 p
Keywords: Doctoral thesis; Electron microscopy for materials research (EMAT)
|
|
|
Vanrompay H (2020) Toward fast and dose efficient electron tomography. 207 p
Keywords: Doctoral thesis; Electron microscopy for materials research (EMAT)
|
|
|
“Transposing testing from lab to on-site environment : a case of cocaine powder sampling”. Van Loon J, De Jong M, De Wael K, Du Bois E, (2020)
Abstract: This paper reports on the transition process to convert a specific lab technique to the on-site, real-life environment. Bringing a lab test to an on-site environment involves many difficulties regarding to the context, people skills and environmental support. Within this project, a case about sampling for an electrochemical measurement, was investigated as a basis to reason upon some general conclusions related to the process of transposing lab-tests to an on-site environment. The current lab test was analysed and compared with a focus group discussion with future users. Based on the findings, assumptions for the new sampling technique in the specific case were formulated. New low-tech methods to achieve the sampling were extensively tested and verified. Starting from this chosen case an argumentation was set up to generalise the conclusions, by reasoning on other cases of products that already passed this transition to the field. Based on a comparison, we could discuss that the selected parameters related to impact of the context environment, of the people that should handle the tests, related to the reasons for transposing the technology, and related to the technology that will be transposed to the on-site environment, were of importance of almost all cases and can therefore be considered as context-independent and related to the transfer to on-site testing.
Keywords: P3 Proceeding; Engineering sciences. Technology; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Product development
|
|
|
Jafarzadeh A (2020) First-principle studies of plasma-catalyst interactions for greenhouse gas conversion. 163 p
Keywords: Doctoral thesis; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|
|
Ranjbar S (2020) Mathematical model of plasma therapy on bacterial growth. 95 p
Keywords: Doctoral thesis; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|
|
Uytdenhouwen Y (2020) Tuning the performance of a DBD plasma reactor for CO2 reforming. 303 p
Keywords: Doctoral thesis; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
|
|
|
Guzzinati G, Das PP, Zompra A A., Nicopoulos S, Verbeeck J (2020) Electron energy loss spectra of several organic compounds
Abstract: We placed crystals of different compounds to explore the possibility of fingerprinting them through EELS. Here are representative datasets of 7 different compounds: b-cyclodextrin hexacarboxy cyclohexane tannin TH-15 peptide TH-27 peptide two different forms of piroxicam The datasets were collected at EMAT, using a monochromated FEI Titan3 TEM, within the scope of an EUSMI request. More information as well as analysis methodologies adopted for the data are detailed in the paper: Das et al. “Reliable Characterization of Organic & Pharmaceutical Compounds with High Resolution Monochromated EEL Spectroscopy”, Polymers 2020, 12(7), 1434.
Keywords: Dataset; Electron microscopy for materials research (EMAT)
DOI: 10.5281/zenodo.3975761
|
|
|
Samaeeaghmiyoni V, Cordier P, Demouchy S, Bollinger C, Gasc J, Mussi A, Schryvers D, Idrissi H (2020) Research data supporting for Stress-induced amorphization triggers deformation in the lithospheric mantle
Keywords: Dataset; Electron microscopy for materials research (EMAT)
DOI: 10.5281/zenodo.3893661
|
|
|
“Integrating PV+battery residential microgrids in distribution networks : how is the point of common coupling agreed upon?”.Saviuc I, Van Passel S, Peremans H in Sustainable Energy for Smart Cities : First EAI International Conference, SESC 2019, Braga, Portugal, December 4–6, 2019: proceedings, page 150 (2020).
Abstract: The anticipated development of decentralized electricity generation is expected to strengthen the opportunities of prosumers in the residential areas of cities, in line with the predicted establishment of renewable energy generation and storage. Based on academic research and on successful case studies, the opportunity for residential prosumers to organize in microgrids emerges as a viable and promising solution. This paper focuses on microgrids that are planned to generate electricity with a PV unit and use a shared storage system, and that opt to have a connection with the main grid. However, the point of common coupling needs to be agreed first between the microgrid operator and the network operator, and this agreement is determined by several factors and conditions beyond the basic technical and regulatory requirements. A survey of academic literature on the determinant factors for such an agreement exposes the fact that current research either focuses on the integration of individual prosumers in the main grid, or regards the point of common coupling as a given component of microgrids. We argue that neither of the two approaches is helpful in the case of microgrids vs. main grid, seeing as the agreement is not self-evident under just any circumstances, nor can the microgrid be equated to a single, large prosumer. Therefore this short paper compiles a set of determinant factors for the microgrid integration, as they emerge from academic literature, with the aim to document further research needs and support the discussion on microgrid integration.
Keywords: H1 Book chapter; Economics; Engineering sciences. Technology; Engineering Management (ENM)
DOI: 10.1007/978-3-030-45694-8_12
|
|
|
Van Schoubroeck S (2020) A techno-sustainability assessment framework : indicator selection and integrated method for sustainability analysis of biobased chemicals. 195 p
Abstract: Biobased chemistry has gained interest and has the potential to tackle some of the sustainability challenges the chemical industry must endure. Sustainability impacts need to be evaluated and monitored to highlight the advantages and pitfalls of different biobased routes over the product life cycle. A better understanding of the potential sustainability of emerging biobased technologies and products is essential to guide additional research and further technology development. This PhD thesis aims to develop a framework for a techno-sustainability assessment (TSA), while accounting for technological as well as economic, environmental, and social aspects in an integrated approach. First, a review of the state-of-the-art sustainability indicators for biobased chemicals was conducted and a gap analysis was performed to identify indicator development needs. Afterwards, a Delphi study was performed to select sustainability indicators specifically for biobased chemical assessment and to reach consensus among experts on a prioritization of these indicators. Next, the selected sustainability indicators were quantified while integrating technological and country-specific data with environmental characterization factors, economic values and social data. Finally, a stochastic, hierarchical multi-criteria decision analysis (MCDA) integrates the independent techno-sustainability indicators expressed in different units, taking into account stochastic and flexible method options. The developed integrated TSA framework was applied to a case for which a production and harvesting plant of microalgae-based food colorants is assessed. The final aim of the integrated TSA is to compare the potential sustainability performance of different scenarios and to make better-informed choices between alternatives by evaluating environmental, economic and social sustainability impacts in one holistic model. Integrated TSA offers a novel framework where decision makers can assess sustainability already in early technology development stages by identifying potential hurdles and opportunities to guide R&D and make sustainable investment decisions.
Keywords: Doctoral thesis; Engineering Management (ENM)
|
|