|
“A parametric model for reactive high-power impulse magnetron sputtering of films”. Kozák T, Vlček J, Journal Of Physics D-Applied Physics 49, 055202 (2016). http://doi.org/10.1088/0022-3727/49/5/055202
Abstract: We present a time-dependent parametric model for reactive HiPIMS deposition of films. Specific features of HiPIMS discharges and a possible increase in the density of the reactive gas in front of the reactive gas inlets placed between the target and the substrate are considered in the model. The model makes it possible to calculate the compound fractions in two target layers and in one substrate layer, and the deposition rate of films at fixed partial pressures of the reactive and inert gas. A simplified relation for the deposition rate of films prepared using a reactive HiPIMS is presented. We used the model to simulate controlled reactive HiPIMS depositions of stoichiometric ZrO2 films, which were recently carried out in our laboratories with two different configurations of the O2 inlets in front of the sputtered target. The repetition frequency was 500 Hz at the deposition-averaged target power densities of 5 Wcm−2 and 50 Wcm−2 with a pulse-averaged target power density up to 2 kWcm−2. The pulse durations were 50 μs and 200 μs. Our model calculations show that the to-substrate O2 inlet provides systematically lower compound fractions in the target surface layer and higher compound fractions in the substrate surface layer, compared with the to-target O2 inlet. The low compound fractions in the target surface layer (being approximately 10% at the depositionaveraged target power density of 50 Wcm−2 and the pulse duration of 200 μs) result in high deposition rates of the films produced, which are in agreement with experimental values.
Keywords: A1 Journal article; Electron Microscopy for Materials Science (EMAT);
Impact Factor: 2.588
Times cited: 25
DOI: 10.1088/0022-3727/49/5/055202
|
|
|
“Sputter-deposited Mg-Al-O thin films: linking molecular dynamics simulations to experiments”. Georgieva V, Saraiva M, Jehanathan N, Lebelev OI, Depla D, Bogaerts A, Journal of physics: D: applied physics 42, 065107 (2009). http://doi.org/10.1088/0022-3727/42/6/065107
Abstract: Using a molecular dynamics model the crystallinity of MgxAlyOz thin films with a variation in the stoichiometry of the thin film is studied at operating conditions similar to the experimental operating conditions of a dual magnetron sputter deposition system. The films are deposited on a crystalline or amorphous substrate. The Mg metal content in the film ranged from 100% (i.e. MgO film) to 0% (i.e. Al2O3 film). The radial distribution function and density of the films are calculated. The results are compared with x-ray diffraction and transmission electron microscopy analyses of experimentally deposited thin films by the dual magnetron reactive sputtering process. Both simulation and experimental results show that the structure of the MgAlO film varies from crystalline to amorphous when the Mg concentration decreases. It seems that the crystalline MgAlO films have a MgO structure with Al atoms in between.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 2.588
Times cited: 37
DOI: 10.1088/0022-3727/42/6/065107
|
|
|
“Effect of oxygen rf-plasma on electronic properties of CNTs”. Felten A, Ghijsen J, Pireaux J-J, Johnson RL, Whelan CM, Liang D, Van Tendeloo G, Journal of physics: D: applied physics 40, 7379 (2007). http://doi.org/10.1088/0022-3727/40/23/019
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.588
Times cited: 25
DOI: 10.1088/0022-3727/40/23/019
|
|
|
“Functionalization of MWCNTs with atomic nitrogen : electronic structure”. Ruelle B, Felten A, Ghijsen J, Drube W, Johnson RL, Liang D, Erni R, Van Tendeloo G, Dubois P, Hecq M, Bittencourt C;, Journal of physics: D: applied physics 41, 045202 (2008). http://doi.org/10.1088/0022-3727/41/4/045202
Abstract: The changes induced by exposing multi-walled carbon nanotubes (CNTs) to atomic nitrogen were analysed by high-resolution transmission electron microscopy (HRTEM), x-ray and ultraviolet photoelectron spectroscopy. It was found that the atomic nitrogen generated by a microwave plasma effectively grafts chemical groups onto the CNT surface altering the density of valence electronic states. HRTEM showed that the exposure to atomic nitrogen does not significantly damage the CNT surface.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.588
Times cited: 16
DOI: 10.1088/0022-3727/41/4/045202
|
|
|
“Optimized fabrication of high-quality La0.67Sr0.33MnO3 thin films considering all essential characteristics”. Boschker H, Huijben M, Vailinois A, Verbeeck J, Van Aert S, Luysberg M, Bals S, Van Tendeloo G, Houwman EP, Koster G, Blank DHA, Rijnders G, Journal of physics: D: applied physics 44, 205001 (2011). http://doi.org/10.1088/0022-3727/44/20/205001
Abstract: In this paper, an overview of the fabrication and properties of high-quality La0.67Sr0.33MnO3 (LSMO) thin films is given. A high-quality LSMO film combines a smooth surface morphology with a large magnetization and a small residual resistivity, while avoiding precipitates and surface segregation. In the literature, typically only a few of these issues are adressed. We therefore present a thorough characterization of our films, which were grown by pulsed laser deposition. The films were characterized with reflection high energy electron diffraction, atomic force microscopy, x-ray diffraction, magnetization and transport measurements, x-ray photoelectron spectroscopy and scanning transmission electron microscopy. The films have a saturation magnetization of 4.0 µB/Mn, a Curie temperature of 350 K and a residual resistivity of 60 µΩ cm. These results indicate that high-quality films, combining both large magnetization and small residual resistivity, were realized. A comparison between different samples presented in the literature shows that focussing on a single property is insufficient for the optimization of the deposition process. For high-quality films, all properties have to be adressed. For LSMO devices, the thin-film quality is crucial for the device performance. Therefore, this research is important for the application of LSMO in devices.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.588
Times cited: 99
DOI: 10.1088/0022-3727/44/20/205001
|
|
|
“Simulation of magnetic circular dichroism in the electron microscope”. Rubino S, Schattschneider P, Rusz J, Verbeeck J, Leifer K, Journal of physics: D: applied physics 43, 474005 (2010). http://doi.org/10.1088/0022-3727/43/47/474005
Abstract: As electron energy-loss spectroscopy (EELS) and x-ray absorption spectroscopy (XAS) probe the same transitions from coreshell states to unoccupied states above the Fermi energy, it should always be possible to apply the two techniques to the same physical phenomena, such as magnetic dichroism, and obtain the same information. Indeed, the similarity in the expression of the electron and x-ray cross-sections had been already exploited to prove the equivalence of x-ray magnetic linear dichroism and anisotropy in EELS, by noting that the polarization vector of a photon plays the same role as the momentum transfer in electron scattering. Recently, the same was proven true for x-ray magnetic circular dichroism (XMCD) by establishing a new TEM technique called EMCD (electron energy-loss magnetic chiral dichroism) (Schattschneider P et al 2006 Nature 441 4868), which makes use of special electron scattering conditions to force the absorption of a circularly polarized virtual photon. The intrinsic advantage of EMCD over XMCD is the high spatial resolution of electron microscopes, which are readily available. Among the particular obstacles in EMCD that do not exist for synchrotron radiation, is the notoriously low signal and the very particular scattering conditions necessary to observe a chiral dichroic signal. In spite of that, impressive progress has been made in recent years. The signal strength could be considerably increased, and some innovations such as using a convergent beam have been introduced. EMCD has evolved into several techniques, which make full use of the versatility of the TEM and energy filtering, spectroscopy or STEM conditions (Rubino S 2007 Magnetic circular dichroism in the transmission electron microscope PhD Thesis Vienna University of Technology, Vienna, Austria).
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.588
Times cited: 13
DOI: 10.1088/0022-3727/43/47/474005
|
|
|
“TEM characterization of extended defects induced in Si wafers by H-plasma treatment”. Ghica C, Nistor LC, Bender H, Richard O, Van Tendeloo G, Ulyashin A, Journal of physics: D: applied physics 40, 395 (2007). http://doi.org/10.1088/0022-3727/40/2/016
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.588
Times cited: 10
DOI: 10.1088/0022-3727/40/2/016
|
|
|
“Tuning of the size and the lattice parameter of ion-beam synthesized Pb nanoparticles embedded in Si”. Wang H, Cuppens J, Biermans E, Bals S, Fernandez-Ballester L, Kvashnina KO, Bras W, van Bael MJ, Temst K, Vantomme A, Journal of physics: D: applied physics 45, 035301 (2012). http://doi.org/10.1088/0022-3727/45/3/035301
Abstract: The size and lattice constant evolution of Pb nanoparticles (NPs) synthesized by high fluence implantation in crystalline Si have been studied with a variety of experimental techniques. Results obtained from small-angle x-ray scattering showed that the Pb NPs grow with increasing implantation fluence and annealing duration. The theory of NP growth kinetics can be applied to qualitatively explain the size evolution of the Pb NPs during the implantation and annealing processes. Moreover, the lattice constant of the Pb NPs was evaluated by conventional x-ray diffraction. The lattice dilatation was observed to decrease with increasing size of the Pb NPs. Such lattice constant tuning can be attributed to the pseudomorphism caused by the lattice mismatch between the Pb NPs and the Si matrix.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.588
Times cited: 5
DOI: 10.1088/0022-3727/45/3/035301
|
|
|
“Etching induced formation of interfacial FeMn in IrMn/CoFe bilayers”. O'Donnell D, Hassan S, Du Y, Gauquelin N, Krishnan D, Verbeeck J, Fan R, Steadman P, Bencok P, Dobrynin AN, Journal of physics: D: applied physics 52, 165002 (2019). http://doi.org/10.1088/1361-6463/AB03BD
Abstract: The effect of ion etching on exchange bias in IrMn3/Co70Fe30 bilayers is investigated. In spite of the reduction of saturation magnetization caused by the embedding of Tr from the capping layer into the Co70Fe30 layer during the etching process, the exchange bias in samples with the same thickness of the Co70Fe30 layer is reducing in proportion to the etching power. X-ray magnetic circular dichroism measurements revealed the emergence of an uncompensated Mn magnetization after etching, which is antiferromagnetically coupled to the ferromagnetic layer. This suggests etching induced formation of small interfacial FeMn regions which leads to the decrease of effective exchange coupling between ferromagnetic and antiferromagnetic layers.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.588
DOI: 10.1088/1361-6463/AB03BD
|
|
|
“An analysis of the physiologic parameters of intraoral wear: a review”. Lawson NC, Janyavula S, Çakir D, Burgess JO, Journal Of Physics D-Applied Physics 46, Unsp 404007 (2013). http://doi.org/10.1088/0022-3727/46/40/404007
Abstract: This paper reviews the conditions of in vivo mastication and describes a novel method of measuring in vitro wear. Methods: parameters of intraoral wear are reviewed in this analysis, including chewing force, tooth sliding distance, food abrasivity, saliva lubrication, and antagonist properties. Results: clinical measurement of mastication forces indicates a range of normal forces between 20 and 140 N for a single molar. During the sliding phase of mastication, horizontal movement has been measured between 0.9 and 2.86 mm. In vivo wear occurs by three-body abrasion when food particles are interposed between teeth and by two-body abrasion after food clearance. Analysis of food particles used in wear testing reveals that food particles are softer than enamel and large enough to separate enamel and restoration surfaces and act as a solid lubricant. In two-body wear, saliva acts as a boundary lubricant with a viscosity of 3 cP. Enamel is the most relevant antagonist material for wear testing. The shape of a palatal cusp has been estimated as a 0.6 mm diameter ball and the hardest region of a tooth is its enamel surface. pH values and temperatures have been shown to range between 2-7 and 5-55 degrees C in intraoral fluids, respectively. These intraoral parameters have been used to modify the Alabama wear testing method.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.588
DOI: 10.1088/0022-3727/46/40/404007
|
|
|
“Fast micromagnetic simulations on GPU-recent advances made with mumax3”. Leliaert J, Dvornik M, Mulkers J, De Clercq J, Milošević, MV, Van Waeyenberge B, Journal of physics: D: applied physics 51, 123002 (2018). http://doi.org/10.1088/1361-6463/AAAB1C
Abstract: In the last twenty years, numerical modeling has become an indispensable part of magnetism research. It has become a standard tool for both the exploration of new systems and for the interpretation of experimental data. In the last five years, the capabilities of micromagnetic modeling have dramatically increased due to the deployment of graphical processing units (GPU), which have sped up calculations to a factor of 200. This has enabled many studies which were previously unfeasible. In this topical review, we give an overview of this modeling approach and show how it has contributed to the forefront of current magnetism research.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.588
Times cited: 65
DOI: 10.1088/1361-6463/AAAB1C
|
|
|
“Coupling of the skyrmion velocity to its breathing mode in periodically notched nanotracks”. Leliaert J, Gypens P, Milošević, MV, Van Waeyenberge B, Mulkers J, Journal of physics: D: applied physics 52, 024003 (2019). http://doi.org/10.1088/1361-6463/AAE7C1
Abstract: A thorough understanding of the skyrmion motion through nanotracks is a prerequisite to realize the full potential of spintronic applications like the skyrmion racetrack memory. One of the challenges is to place the data, i.e. skyrmions, on discrete fixed positions, e.g. below a read or write head. In the domain-wall racetrack memory, one proposed solution to this problem was patterning the nanotrack with notches. Following this approach, this paper reports on the skyrmion mobility through a nanotrack with periodic notches (constrictions) made using variations in the chiral Dzyaloshinskii-Moriya interaction. We observe that such notches induce a coupling between the mobility and the skyrmion breathing mode, which manifests itself as velocity-dependent oscillations of the skyrmion diameter and plateaus in which the velocity is independent of the driving force. Despite the fact that domain walls are far more rigid objects than skyrmions, we were able to perform an analogous study and, surprisingly, found even larger plateaus of constant velocity. For both systems it is straightforward to tune the velocity at these plateaus by changing the design of the notched nanotrack geometry, e.g. by varying the distance between the notches. Therefore, the notch-induced coupling between the excited modes and the mobility could offer a strategy to stabilize the velocity against unwanted perturbations in racetrack-like applications. In the last part of the paper we focus on the low-current mobility regimes, whose very rich dynamics at nonzero temperatures are very similar to the operating principle of recently developed probabilistic logic devices. This proves that the mobility of nanomagnetic structures through a periodically modulated track is not only interesting from a fundamental point of view, but has a future in many spintronic applications.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.588
Times cited: 10
DOI: 10.1088/1361-6463/AAE7C1
|
|
|
“Excitation and propagation of spin waves in non-uniformly magnetized waveguides”. Vanderveken F, Ahmad H, Heyns M, Sorée B, Adelmann C, Ciubotaru F, Journal Of Physics D-Applied Physics 53, 495006 (2020). http://doi.org/10.1088/1361-6463/ABB2BE
Abstract: The characteristics of spin waves in ferromagnetic waveguides with non-uniform magnetization have been investigated for situations where the shape anisotropy field of the waveguide is comparable to the external bias field. Spin-wave generation was realized by the magnetoelastic effect by applying normal and shear strain components, as well as by the Oersted field emitted by an inductive antenna. The magnetoelastic excitation field has a non-uniform profile over the width of the waveguide because of the non-uniform magnetization orientation, whereas the Oersted field remains uniform. Using micromagnetic simulations, we indicate that both types of excitation fields generate quantised width modes with both odd and even mode numbers as well as tilted phase fronts. We demonstrate that these effects originate from the average magnetization orientation with respect to the main axes of the magnetic waveguide. Furthermore, it is indicated that the excitation efficiency of the second-order mode generally surpasses that of the first-order mode due to their symmetry. The relative intensity of the excited modes can be controlled by the strain state as well as by tuning the dimensions of the excitation area. Finally, we demonstrate that the nonreciprocity of spin-wave radiation due to the chirality of an Oersted field generated by an inductive antenna is absent for magnetoelastic spin-wave excitation.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.4
Times cited: 1
DOI: 10.1088/1361-6463/ABB2BE
|
|
|
“Van der Waals heterostructures of MoS₂, and Janus MoSSe monolayers on graphitic boron-carbon-nitride (BC₃, C₃N, C₃N₄, and C₄N₃) nanosheets: a first-principles study”. Bafekry A, Yagmurcukardes M, Akgenc B, Ghergherehchi M, Nguyen C, Journal Of Physics D-Applied Physics , 1 (2020). http://doi.org/10.1088/1361-6463/AB876C
Abstract: In this work, we extensively investigate the structural and electronic properties of van der Waals heterostructures (HTs) constructed by MoS${2}$/$BC3$, MoS${2}$/$C3N$, MoS${2}$/$C3N4$, MoS${2}$/$C4N3$ and those using Janus MoSSe instead of MoS$2$ by performing density functional theory calculations. The electronic band structure calculations and the corresponding partial density of states reveal that the significant changes are driven by quite strong layer-layer interaction between the constitutive layers. Our results show that although all monolayers are semiconductors as free-standing layers, the MoS${2}$/$C3N$ and MoS${2}$/$C4N3$ bilayer HTs display metallic behavior as a consequence of transfer of charge carriers between two constituent layers. In addition, it is found that in MoSSe/$C3N$ bilayer HT, the degree of metallicity is affected by the interface chalcogen atom type when Se atoms are facing to $C3N$ layer, the overlap of the bands around the Fermi level is smaller. Moreover, the half-metallic magnetic $C4N3$ is shown to form magnetic half-metallic trilayer HT with MoS$2$ independent of the stacking sequence, i.e. whether it is sandwiched or two $C4N3$ layer encapsulate MoS$2$ layer. We further analyze the trilayer HTs in which MoS$2$ is encapsulated by two different monolayers and it is revealed that at least with one magnetic monolayer, it is possible to construct a magnetic trilayer. While the trilayer of $C4N3$/MoS${2}$/$BC3$ and $C4N3$/MoS${2}$/$C3N4$ exhibit half-metallic characteristics, $C4N3$/MoS${_2}$/$C3$N possesses a magnetic metallic ground state. Overall, our results reveal that holly structures of BCN crystals are suitable for heterostructure formation even over van der Waals type interaction which significantly changes electronic nature of the constituent layers.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.4
DOI: 10.1088/1361-6463/AB876C
|
|
|
“MoSi₂N₄, single-layer : a novel two-dimensional material with outstanding mechanical, thermal, electronic and optical properties”. Bafekry A, Faraji M, Hoat DM, Shahrokhi M, Fadlallah MM, Shojaei F, Feghhi SAH, Ghergherehchi M, Gogova D, Journal Of Physics D-Applied Physics 54, 155303 (2021). http://doi.org/10.1088/1361-6463/ABDB6B
Abstract: Very recently, the 2D form of MoSi2N4 has been successfully fabricated (Hong et al 2020 Science 369 670). Motivated by these recent experimental results, we investigate the structural, mechanical, thermal, electronic and optical properties of the MoSi2N4 monolayer. The mechanical study confirms the stability of the MoSi2N4 monolayer. The Young's modulus decreases by similar to 30%, while the Poisson's ratio increases by similar to 30% compared to the corresponding values of graphene. In addition, the MoSi2N4 monolayer's work function is very similar to that of phosphorene and MoS2 monolayers. The electronic structure shows that the MoSi2N4 monolayer is an indirect semiconductor with a band gaps of 1.79 (2.35) eV using the GGA (HSE06) functional. The thermoelectric performance of the MoSi2N4 monolayer has been revealed and a figure of merit slightly larger than unity at high temperatures is calculated. The optical analysis shows that the first absorption peak for in-plane polarization is located in the visible range of the spectrum, therefore, the MoSi2N4 monolayer is a promising candidate for advanced optoelectronic nanodevices. In summary, the fascinating MoSi2N4 monoloayer is a promising 2D material for many applications due to its unique physical properties.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.588
DOI: 10.1088/1361-6463/ABDB6B
|
|
|
“Prediction of two-dimensional bismuth-based chalcogenides Bi₂X₃(X = S, Se, Te) monolayers with orthorhombic structure : a first-principles study”. Bafekry A, Faraji M, Fadlallah MM, Jappor HR, Hieu NN, Ghergherehchi M, Feghhi SAH, Gogova D, Journal Of Physics D-Applied Physics 54, 395103 (2021). http://doi.org/10.1088/1361-6463/AC118C
Abstract: First-principles calculation is a very powerful tool for discovery and design of novel two-dimensional materials with unique properties needed for the next generation technology. Motivated by the successful preparation of Bi2S3 nanosheets with orthorhombic structure in the last year, herein we gain a deep theoretical insight into the crystal structure, stability, electronic and optical properties of Bi2X3 (X = S, Se, Te) monolayers of orthorhombic phase employing the first-principles calculations. The Molecular dynamics study, phonon spectra, criteria for elastic stability, and cohesive energy results confirm the desired stability of the Bi2X3 monolayers. From S, to Se and Te, the work function value as well as stability of the systems decrease due to the decline in electronegativity. Mechanical properties study reveals that Bi2X3 monolayers have brittle nature. The electronic bandgap values of Bi2S3, Bi2Se3 and Bi2Te3 monolayers are predicted by the HSE06 functional to be 2.05, 1.20 and 1.16 eV, respectively. By assessing the optical properties, it has been found that Bi2X3 monolayers can absorb ultraviolet light. The high in-plane optical anisotropy offers an additional degree of freedom in the design of optical devices. The properties revealed in our survey will stimulate and inspire the search for new approaches of orthorhombic Bi2X3 (X = S, Se, Te) monolayers synthesis and properties manipulation for fabrication of novel nanoelectronic and optoelectronic devices.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.588
DOI: 10.1088/1361-6463/AC118C
|
|