|
“Enhancing the hydrogen evolution properties of kesterite absorber by Si-doping in the surface of CZTS thin film”. Vishwakarma M, Kumar M, Hendrickx M, Hadermann J, Singh AP, Batra Y, Mehta BR, Advanced Materials Interfaces , 2002124 (2021). http://doi.org/10.1002/ADMI.202002124
Abstract: In this work, the effects of Si-doping in Cu2ZnSnS4 are examined computationally and experimentally. The density functional theory calculations show that an increasing concentration of Si (from x = 0 to x = 1) yields a band gap rise due to shifting of the conduction band minimum towards higher energy states in the Cu2Zn(Sn1-xSix)S-4. CZTSiS thin film prepared by co-sputtering process shows Cu2Zn(Sn1-xSix)S-4 (Si-rich) and Cu2ZnSnS4 (S-rich) kesterite phases on the surface and in the bulk of the sample, respectively. A significant change in surface electronic properties is observed in CZTSiS thin film. Si-doping in CZTS inverts the band bending at grain-boundaries from downward to upward and the Fermi level of CZTSiS shifts upward. Further, the coating of the CdS and ZnO layer improves the photocurrent to approximate to 5.57 mA cm(-2) at -0.41 V-RHE in the CZTSiS/CdS/ZnO sample, which is 2.39 times higher than that of pure CZTS. The flat band potential increases from CZTS approximate to 0.43 V-RHE to CZTSiS/CdS/ZnO approximate to 1.31 V-RHE indicating the faster carrier separation process at the electrode-electrolyte interface in the latter sample. CdS/ZnO layers over CZTSiS significantly reduce the charge transfer resistance at the semiconductor-electrolyte interface.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 4.279
DOI: 10.1002/ADMI.202002124
|
|
|
“Precipitation behaviors in Ti-2.3 Wt Pct Cu alloy during isothermal and two-step aging”. Akamine H, Mitsuhara M, Nishida M, Samaee V, Schryvers D, Tsukamoto G, Kunieda T, Fujii H, Metallurgical And Materials Transactions A-Physical Metallurgy And Materials Science 52, 2760 (2021). http://doi.org/10.1007/S11661-021-06265-X
Abstract: Time evolution of precipitates related to age-hardening in Ti-2.3 wt pct Cu alloys was investigated by electron microscopy. In isothermal aging at 723 K, the hardness increases continuously owing to precipitation strengthening, whereas in two-step aging where the aging temperature is switched from 673 K to 873 K after 100 hours, the hardness is found to drastically drop after the aging temperature switches. In isothermal aging, metastable and stable precipitates are independently nucleated, whereas characteristic V-shaped clusters of precipitates are observed during the two-step aging. It is revealed by atomic-scale observations that the V-shaped clusters are composed of metastable and stable precipitates and each type of precipitate has a different orientation relationship with the alpha phase: (10 (3) over bar)//(0001)(alpha) and [0 (1) over bar0]//respectively. The drop in hardness during two-step aging can be explained by a synergistic effect of decreased precipitation strengthening and solid solution strengthening. (C) The Minerals, Metals & Materials Society and ASM International 2021
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 1.874
DOI: 10.1007/S11661-021-06265-X
|
|
|
“Synergistic effects altering reaction pathways : the case of glucose hydrogenation over Fe-Ni catalysts”. Fu Y, Ding L, Singleton ML, Idrissi H, Hermans S, Applied Catalysis B-Environmental 288, 119997 (2021). http://doi.org/10.1016/J.APCATB.2021.119997
Abstract: Carbon black (CB) supported Ni, Fe, or Fe-Ni alloy catalysts were synthesized by sol-gel to elucidate the reaction pathways over each catalyst, as well as synergistic effects in glucose to sorbitol hydrogenation. The bimetallic materials presented small and alloyed nanoparticles that were richer in reduced metallic sites at the surface than their monometallic counterparts. Glucose isomerization to fructose was favoured over Fe/CB, while glucose hydrogenation to sorbitol is the dominating pathway over Ni/CB catalyst. By contrast, sorbitol production was promoted and undesired isomerization was suppressed when Fe and Ni formed a nanoalloy. In addition, the alloy catalyst presented better stability than the corresponding monometallic catalyst. A comparison with a mechanical mixture of Fe/CB and Ni/CB monometallic catalysts demonstrated the synergy at the nanoscale in the alloy. By comparing different Fe:Ni ratios, the 1:1 formulation was identified as the best compromise to achieve a high activity while maintaining high sorbitol selectivity.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 9.446
DOI: 10.1016/J.APCATB.2021.119997
|
|
|
Skorikov A, Heyvaert W, Albrecht W, Pelt DM, Bals S (2021) EMAT Simulated 3D Nanoparticle Structures Dataset
Abstract: This dataset contains 1000 simulated nanoparticle-like 3D structures and noisy EDX-like elemental maps based on them. These data are intended to be used for quantitative analysis of data processing methods in (EDX) tomography of nanoparticles and training the data-driven approaches for these tasks. The dataset is structured as follows: voxel_data/clean 3D voxel grid representation of the simulated nanoparticles. Voxel intensities are adjusted so that the total intensity equals 103. All 3D structures have unique identifiers in 0..999 range. The data derived from a 3D structure preserves this unique identifier. sinograms/clean Tilt series of projection images obtained from the corresponding 3D structures over an angular range of -75..75 degrees with a tilt step of 10 degrees to simulate a typical tilt series used in EDX tomography. Total intensity in each projection image equals 103. sinograms/noisy Tilt series of projection images corrupted with Poisson noise and an additional spatially uniform background noise. projections/clean Projection images extracted from the clean tilt series at 0 degrees tilt angle. projections/noisy Projection images extracted from the noisy tilt series at 0 degrees tilt angle. images/clean Visualizations of the clean projections as PNG images with the intensity range adjusted to 0..255 images/noisy Visualizations of the noisy projections as PNG images with the intensity range adjusted to 0..255
Keywords: Dataset; Electron microscopy for materials research (EMAT)
DOI: 10.5281/zenodo.4580545
|
|
|
“Advanced imaging and simulations of precipitate interfaces in aluminium alloys and their role in phase transformations”. Zhang Z, Bourgeois L, Zhang Y, Rosalie JM, Medhekar N, MATEC web of conferences
T2 –, 17th International Conference on Aluminium Alloys (ICAA), October 26-29, 2020 , 09003 (2020). http://doi.org/10.1051/MATECCONF/202032609003
Abstract: Precipitation is accompanied by the formation and migration of heterophase interfaces. Using the combined approach of advanced imaging and atomistic simulations, we studied the precipitate-matrix interfaces in various aluminium alloy systems, aiming to resolve their detailed atomic structures and illuminate their role in phase transformations.
Keywords: P1 Proceeding; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
DOI: 10.1051/MATECCONF/202032609003
|
|
|
“Beyond surface redox and oxygen mobility at pd-polar ceria (100) interface : underlying principle for strong metal-support interactions in green catalysis”. Mahadi AH, Ye L, Fairclough SM, Qu J, Wu S, Chen W, Papaioannou E, Ray B, Pennycook TJ, Haigh SJ, Young NP, Tedsree K, Metcalfe IS, Tsang SCE, Applied Catalysis B-Environmental 270, 118843 (2020). http://doi.org/10.1016/J.APCATB.2020.118843
Abstract: When ceria is used as a support for many redox catalysis involved in green catalysis, it is well-known that the overlying noble metal can gain access to a significant quantity of oxygen atoms with high mobility and fast reduction and oxidation properties under mild conditions. However, it is as yet unclear what the underlying principle and the nature of the ceria surface involved are. By using two tailored morphologies of ceria nanocrystals, namely cubes and rods, it is demonstrated from Scanning Transmission Electron Microscopy with Electron Energy Loss Spectroscopy (STEM-EELS) mapping and Pulse Isotopic Exchange (PIE) that ceria nano-cubes terminated with a polar surface (100) can give access to more than the top most layer of surface oxygen atoms. Also, they give higher oxygen mobility than ceria nanorods with a non-polar facet of (110). A new insight for the possible additional role of polar ceria surface plays in the oxygen mobility is obtained from Density Functional Theory (DFT) calculations which suggest that the (100) surface sites that has more than half-filled O on same plane can drive oxygen atoms to oxidise adsorbate(s) on Pd due to the strong electrostatic repulsion.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 22.1
DOI: 10.1016/J.APCATB.2020.118843
|
|
|
“Effect of cobalt content on the properties of quintuple perovskites Sm₂Ba₃Fe₅-xCoxO₁₅-δ”. Golovachev IB, Mychinko MY, Volkova NE, Gavrilova LY, Raveau B, Maignan A, Cherepanov VA, Journal Of Solid State Chemistry 301, 122324 (2021). http://doi.org/10.1016/J.JSSC.2021.122324
Abstract: Quintuple perovskites Sm2Ba3Fe5-xCoxO15-delta = 0.5, 1.0 and 1.5) have been prepared by glycerin-nitrate tech- nique in air. The phase purity was confirmed by XRD. Partial substitution of Co for Fe decreases the oxygen content and thus the mean oxidation state of 3d-metals. It also slightly decreases the thermal expansion coefficient of oxides. Positive value of the Seebeck coefficient confirmed p-type conductivity, though the thermopower decreases as the Co content increases. The temperature dependence of electrical conductivity reveals a maximum at 550-750 degrees C.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.299
DOI: 10.1016/J.JSSC.2021.122324
|
|
|
“On the nucleation mechanism of {112} <, 111 >, mechanical twins in as-quenched beta metastable Ti-12 wt.% Mo alloy”. Marteleur M, Idrissi H, Amin-Ahmadi B, Prima F, Schryvers D, Jacques PJ, Materialia 7, Unsp 100418 (2019). http://doi.org/10.1016/J.MTLA.2019.100418
Abstract: Recently developed beta-metastable Ti grades take advantage of the simultaneous activation of TRIP and TWIP effects for enhancing their work hardening rate. However, the role of each plasticity mechanism on the macroscopic mechanical response is still unclear. In this work, the nucleation mechanism of the first activated plasticity mechanism, namely {112} < 111 > twinning, was investigated. Firstly, post-mortem TEM analysis showed that twins nucleate on pre-existing microstructural defects such as thermal jogs with the zonal dislocation mechanism. The precipitation of the omega phase on twin boundaries has been observed, as well as the emission of numerous dislocations from super-jogs present in these twin boundaries. It is also shown that {112} < 111 > twins act as effective dislocation sources for the subsequent plasticity mechanisms such as beta -> alpha '' martensitic transformation and {332} < 111 > twinning. Secondly, in situ TEM tensile testing of the investigated Ti grade highlighted the primary role of the initial defect configuration present in the microstructure. It is shown that twins cannot nucleate without the presence of specific defects allowing the triggering of the dislocation decomposition needed for the twinning mechanism highlighted in investigated bulk samples.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
DOI: 10.1016/J.MTLA.2019.100418
|
|
|
“Rheology of amorphous olivine thin films characterized by nanoindentation”. Baral P, Orekhov A, Dohmen R, Coulombier M, Raskin JP, Cordier P, Idrissi H, Pardoen T, Acta Materialia 219, 117257 (2021). http://doi.org/10.1016/J.ACTAMAT.2021.117257
Abstract: The rheological properties of amorphous olivine thin films deposited by pulsed laser deposition have been studied based on ambient temperature nanoindentation under constant strain-rate as well as re-laxation conditions. The amorphous olivine films exhibit a viscoelastic-viscoplastic behavior with a significant rate dependency. The strain-rate sensitivity m is equal to similar to 0 . 05 which is very high for silicates, indicating a complex out-of-equilibrium structure. The minimum apparent activation volume determined from nanoindentation experiments corresponds to Mg and Fe atomic metallic sites in the (Mg,Fe)(2)SiO4 crystalline lattice. The ambient temperature creep behavior of the amorphous olivine films differs very much from the one of single crystal olivine. This behavior directly connects to the recent demonstration of the activation of grain boundary sliding in polycrystalline olivine following grain boundary amorphization under high-stress. (C) 2021 The Authors. Published by Elsevier Ltd on behalf of Acta Materialia Inc.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 5.301
DOI: 10.1016/J.ACTAMAT.2021.117257
|
|
|
“Shearing and rotation of β'' and β' precipitates in an Al-Mg-Si alloy under tensile deformation : in-situ and ex-situ studies”. Yang M, Orekhov A, Hu Z-Y, Feng M, Jin S, Sha G, Li K, Samaee V, Song M, Du Y, Van Tendeloo G, Schryvers D, Acta Materialia 220, 117310 (2021). http://doi.org/10.1016/J.ACTAMAT.2021.117310
Abstract: The interaction between dislocations and nano-precipitates during deformation directly influences hardening response of precipitation-strengthening metals such as Al-Mg-Si alloys. However, how coherent and semi-coherent nano-precipitates accommodate external deformation applied to an Al alloy remains to be elucidated. In-situ tensile experiments in a transmission electron microscope (TEM) were conducted to study the dynamic process of dislocations cutting through coherent needle-like beta '' precipitates with diameters of 3 similar to 8 nm. Comprehensive investigations using in-situ, ex-situ TEM and atom probe tomography uncovered that beta '' precipitates were firstly sheared into small fragments, and then the rotation of the fragments, via sliding along precipitate/matrix interfaces, destroyed their initially coherent interface with the Al matrix. In contrast, semi-coherent beta' precipitates with sizes similar to beta '' were more difficult to be fragmented and accumulation of dislocations at the interface increased interface misfit between beta' and the Al matrix. Consequently, beta' precipitates could basically maintain their needle-like shape after the tensile deformation. This research gains new insights into the interaction between nano-precipitates and dislocations. (C) 2021 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 5.301
DOI: 10.1016/J.ACTAMAT.2021.117310
|
|
|
“TEM investigation of SCC crack tips in high Si stainless steel tapered specimens”. Penders A, Konstantinovic MJ, Van Renterghem W, Bosch RW, Schryvers D, Corrosion Engineering Science And Technology (2021). http://doi.org/10.1080/1478422X.2021.1961665
Abstract: The stress corrosion cracking (SCC) mechanism is investigated in high Si duplex stainless steel in a simulated PWR environment based on TEM analysis of FIB-extracted SCC crack tips. The microstructural investigation in the near vicinity of SCC crack tips illustrates a strain-rate dependence in SCC mechanisms. Detailed analysis of the crack tip morphology, that includes crack tip oxidation and surrounding deformation field, indicates the existence of an interplay between corrosion- and deformation-driven failure as a function of the strain rate. Slow strain-rate crack tips exhibit a narrow cleavage failure which can be linked to the film-induced failure mechanism, while rounded shaped crack tips for faster strain rates could be related to the strain-induced failure. As a result, two nominal strain-rate-dependent failure regimes dominated either by corrosion or deformation-driven cracking mechanisms can be distinguished.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 0.879
DOI: 10.1080/1478422X.2021.1961665
|
|
|
“Towards ductilization of high strength 7XXX aluminium alloys via microstructural modifications obtained by friction stir processing and heat treatments”. Lezaack MB, Hannard F, Zhao L, Orekhov A, Adrien J, Miettinen A, Idrissi H, Simar A, Materialia 20, 101248 (2021). http://doi.org/10.1016/J.MTLA.2021.101248
Abstract: High strength 7XXX aluminium series reach exceptional strength, higher than all other industrial aluminium alloys. However, they suffer from a lack of ductility compared to softer series. This work presents a procedure to improve the ductility of 7475 Al alloy in high strength condition, reaching a true fracture strain of 70% at full 500 MPa T6 yield strength. Using friction stir processing (FSP) and post-FSP heat treatments, 100% of industrial rolled material T6 yield stress is maintained but a 180% increase in fracture strain is measured for the processed material. This ductility improvement is studied by in-situ synchrotron X-ray tomography and is explained by the reduction of intermetallic particles size and the homogenization of their spatial distribution. Furthermore, the microstructure after FSP shows equiaxed refined grains which favour crack deviation as opposed to large cracks parallel to the elongated coarse grains in rolled plate. These results are paving the way to better formability and crashworthiness of 7XXX alloys.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
DOI: 10.1016/J.MTLA.2021.101248
|
|
|
“Accounting for externalities in cross-sectional economic models of climate change impacts”. Moretti M, Vanschoenwinkel J, Van Passel S, Ecological Economics 185, 107058 (2021). http://doi.org/10.1016/J.ECOLECON.2021.107058
Abstract: Environmental effects and natural resources depletion associated with agriculture production affect the agriculture response to climate change. Traditional cross-sectional climate response models ignore this requirement. This research estimates the impact of climate on European agriculture using a continental scale Ricardian analysis. We correct farm income by accounting for resources (energy, fertilisers, pesticides, and water) use intensity and calculate the sustainable value for a sample of 9497 specialized field crop farms. Compared with the traditional Ricardian method, the marginal effects of temperature remain positive (but less positive) in Northern countries, while it leads to less damages in Southern countries when net revenue and farms? sustainable values are used as dependent variables. Accounting for the environmental effects and depletion of natural capital improves the ability of the Ricardian method to estimate agriculture climate response functions in the long run.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
Impact Factor: 2.965
DOI: 10.1016/J.ECOLECON.2021.107058
|
|
|
Peeters M (2021) The added value of Smart Product-Service Systems to real estate developments. 117 p
Abstract: Socially responsible investments can be defined as an investment process that integrates ethical values and environmental protection, improving social conditions, and good governance into a traditional investment decision. This integration is mainly a consequence of the growing importance that investors give to environmental, social, and governance (ESG) criteria, resulting in more sustainable development. Also, in the real estate sector, increased attention is being paid to the contributions made to integrate economic, environmental, and social factors into decisions. The ESG framework looks closely at how companies are managed, and the impact related to their market value. The factors for investors’ focus are summarized as environmental, social, and governance. The term ESG was coined in a 2004 United Nations (UN) report titled “Who Cares Wins,” aimed at raising awareness regarding the importance of environmental, social, and corporate governance issues in financial markets. The ESG criteria’s specific purpose is to guide investors in recognizing sustainable investments without evaluating how sustainable the asset is or the investment value represented by sustainability. It is essential to underline that ESG does not take specific economic interests into account. The rationale behind this apparent gap is that investors investigate the economic aspects before investing. However, by not explicitly linking ESG and economic criteria, attractive investments are often misjudged and not implemented. For example, investments that only show their value in the longer term or indirectly influence value by achieving a higher retention rate among incumbent tenants, reducing or eliminating friction costs. A product–service system (PSS) refers to a market proposition (business model) that builds on a product’s traditional functionality by incorporating additional services. Although services are already offered, the PSS function is to link the service to a product. The service thereby supports the operation of the product and generates additional benefits. It encompasses the integrated solutions of products and services to satisfy customers' needs and generate maximum value. According to Sutanto et al., a PSS is designed to focus on sustainability characterized in three dimensions. 1. The economic dimension 2. The environmental dimension 3. The social dimension When discussing sustainability in this thesis, we use the criteria listed above related to socially responsible investments. The link between PSS and ESG is that a PSS focuses on creating a sustainable system, and ESG makes sustainability more visible to investors. Therefore, when PSS are recognized and implemented in buildings, they must be evaluated using ESG analysis methods. Product-Service Systems (PSS) try to find a way to offer services on top of a product. The product is essentially secondary to the result that is delivered from the services. For example, the modem (product) that a cable company provides will be of secondary importance to the connectivity (service). Alternatively, it will be less critical how heat is made (product) than the intended set point is achieved in the building. PSSs transform the supply of products into services. In doing so, the responsibility shifts from delivering a product (once only) to continuous service delivery. Therefore, it is in the best interest of the service provider to deliver the outcome of the service as efficiently (read: lowest cost) as possible. A direct consequence of this is that the service provider will want to use the product as efficiently as possible and as long as possible to reduce his costs. Therefore, the supplier will also want to recover and maximize the reuse of his product based on the same rationale. A positive impact on the environment and the used raw materials is thus to be expected. The whole process of servitization (transforming products into services) in real estate will positively impact the Economic, Environmental and Social factors. Therefore, demonstrating this proposition is the main objective of this thesis. Smart PSS is the same idea as Product-Service systems but in which the digitization of the services plays a key role. It will be shown that by digitizing services, a broader range can be offered. It will be demonstrated that products that provide services at the building level can, through their interconnectedness, also provide services to external systems (e.g. electricity grid, urban planning, mobility, ...). At the same time, digitizing the products and services will also underpin trust in the systems and allow for proper remuneration. In this PhD, different standard systems in a building, such as the reservation system, the water heater, or the fire detection system, are equipped with additional services. A PSS is often specifically designed to focus on economic, social, and environmental dimensions. These dimensions correspond to the investor’s examination as part of the ESG analysis before investing. As the PSS is often specifically designed to integrate sustainability, there is a close link between the sustainability performance of the PSS and the ESG criteria evaluated by the investor. Throughout the work, the owner is considered to be the user of the building. It is not the case that only an owner-user can generate cash flow. In essence, if they have sufficient rights to the underlying product, any building user can activate services that generate cash flow. In today's market, it is logical that this is viewed in the owner-user context as they will usually choose the products to be installed in larger technical installations. They may have previously used a PSS or choose to move to one. However, a building’s tenant could choose to lease out their meeting rooms if they are not contractually prohibited from doing so since, in practice, contracts have begun to prohibit certain services. For example, rental contracts that actively prohibit renting out a property through platforms such as Airbnb. Thus, the user’s function could potentially impact how the PSS is designed. This work does not explicitly explore the impact of this aspect. The owner-user is assumed throughout this manuscript. The second chapter describes the state of affairs concerning PSSs in a broad framework evolving towards focusing on the real estate sector. After which, in the second chapter, ESG and the link to real estate and how smart real estate (smart buildings) is missing from this evaluation are discussed in more detail. Chapter 3 shows from a fire alarm system, which was extended with an evacuation support system, the usefulness, and the risk of data. Further work was done to demonstrate the added value in terms of Economic, Environmental and Social factors of standard installations in buildings. In Chapter 4, a simple sanitary hot water boiler is extended with a service that allows controlling this boiler according to the status of the electricity grid (surplus or shortage of energy). The supply and demand of energy on the power grid must be equal at all times. By equipping a classic water heater (product) with additional intelligence (service), it becomes possible to adjust the energy use to the grid's needs. The grid operators are prepared to pay for this. This payment can be linked to different energy markets (long term market, spot market, ...). This study looked at the fee that would have to be paid when the adjustment of the energy use can be made instantaneously so that the fee must be settled according to the prices on the imbalance market. In chapter 5, we look at the impact of the service to rent out free spaces as co-working places on a broad market (external to the building), compared to a regular reservation system. By renting out unused workplaces on a broad market, the utilization of the existing patrimony will be higher. The demand for new square meters with the same function will decrease as the supply-demand curve changes, and so will the price. This makes it less interesting to build new buildings. Less construction of new buildings will result in fewer resources being used, which will positively affect the environment. In addition, fewer new buildings with an office function will leave more space for buildings with another function. Also, the city's infrastructure will be less burdened (roads, sewerage, electricity grid,...). In The Hague, the decreasing need for new square meters of office buildings can lead to more space for affordable housing, for which the city has a great need. Chapter 6 will frame the valuation of service as a real options method that gives an impetus to a general valuation methodology to value the flexibility that Smart PSS inherently has. Finally, this thesis demonstrates that (smart) PSSs impact real estate profitability, while positively influencing environmental and social factors. Further research and the limitations of the studies conducted are documented. This PhD concludes that Product-Service systems should break the silos between different stakeholders, resulting in a lower total cost of ownership of buildings in the longer term. This can only be achieved if the valuation of Product-Service systems is done correctly and is recognized by every stakeholder in the real estate process.
Keywords: Doctoral thesis; Economics; Engineering Management (ENM); Internet Data Lab (IDLab)
|
|
|
“Ex-ante LCA of emerging carbon steel slag treatment technologies : fast forwarding lab observations to industrial-scale production”. Buyle M, Maes B, Van Passel S, Boonen K, Vercalsteren A, Audenaert A, Journal Of Cleaner Production 313, 127921 (2021). http://doi.org/10.1016/J.JCLEPRO.2021.127921
Abstract: The valuable properties of carbon steel slag are currently underexploited. To date, research mainly focusses on valorising a single property of the slag. In this study an ex-ante life cycle assessment (LCA) was applied to evaluate the environmental profile of a novel technological pathway aimed at the extraction of chromium from carbon steel slag in combination with high quality valorisation of the residual matrix material. A comparison with current practice was made, not only by calculating the environmental impact of the lab scale observations, but more importantly by estimating the impact on an industrial scale. Practical guidance on ex-ante LCA is limited, so this study contributes by incorporating simulations on thermodynamic behaviour, complemented with empirical calculation rules and including information derived from similar technologies to perform the upscaling. These principles of ex-ante LCA were applied to the lab results of two consecutive research iterations. Substantial improvements of the environmental profile were observed: ex-ante results turned out to be a factor 20 lower compared to the results from the lab observations after the first iteration and had decreased by a factor 2 compared to the small pilot scale of the second iteration. All upscaled results are better than those from the worst case reference scenario (landfill). Based on the experience gained after this iterative research cycle, a practical recommendation is that at a low technology readiness level using more simple calculation rules in combination with a flowsheet based on elementary design principles for processes at an industrial scale is a more efficient way of modelling compared to a fully-fledged process design from the start.
Keywords: A1 Journal article; Engineering sciences. Technology; Energy and Materials in Infrastructure and Buildings (EMIB)
Impact Factor: 5.715
DOI: 10.1016/J.JCLEPRO.2021.127921
|
|
|
“Farmers' decision to use drought early warning system in developing countries”. Sharafi L, Zarafshani K, Keshavarz M, Azadi H, Van Passel S, Science Of The Total Environment 758, 142761 (2021). http://doi.org/10.1016/J.SCITOTENV.2020.142761
Abstract: Drought is a persistent, sluggish natural disaster in developing countries that has generated a financial burden and an unstable climate. Farmers should adopt early warning systems (EWS) in their strategies for monitoring drought to reduce its serious consequences. However, farmers in developing countries are reluctant to use EWS as their management strategies. Hence, the aim of this study was to investigate the decision of farmers to use climate knowledge through the model of farming activity in Kermanshah Township, Iran. A surveyor questionnaire was used to gather data from 370 wheat farmers using random sampling methods inmulti-stage clusters. Results revealed that the decision to use climate information is affected by personal factors, attitude towards climate information, objectives of using climate information, and external/physical farming factors. The result of this study has implications for drought management practitioners. To be specific, the results can aid policymakers to design early alert programs to minimize the risk of drought and thus move from conventional to climate smart agriculture. (C) 2020 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Engineering Management (ENM)
Impact Factor: 4.9
DOI: 10.1016/J.SCITOTENV.2020.142761
|
|
|
Chekol Zewdie M (2021) How irrigation water impacts Ethiopian agriculture : an applied economics study. xiv, 152 p
Abstract: In recent decades, as crop production has increased in many areas where irrigation projects have been implemented, the global agricultural development community has promoted irrigation investments. However, due to the disappointing performance of irrigation farming in developing countries, irrigation intervention in Africa South of the Sahara including Ethiopia is an issue of debate. Moreover, several gaps exist in the Ethiopian irrigation farming literature. For instance, evidence about the direct and indirect effects of irrigation water on agriculture is not well documented. The irrigation farming literature has not disentangled the indirect effects of having access to irrigation water from the direct effect and the indirect effects have been underrepresented. Furthermore, most previous studies have applied either a quantitative or qualitative approach and have relied only on revealed data as main type of methodology, making studies that combine qualitative and quantitative research and that use both stated and revealed data underrepresented. In this study, different approaches have been applied to investigate how irrigation water impacts Ethiopia agriculture with special attention being given to disentangling the direct and indirect effects of irrigation water on Ethiopian agriculture. Using a structural equation model, a stochastic production frontier approach, and a discrete choice experiment, I drew evidence regarding the direct and indirect effects of irrigation water on crop revenue of smallholder farmers, the technical efficiency of irrigation user farmers, and the farmers’ willingness to pay to improve poor irrigation schemes from field observations, semi-structured interviews and focus group discussions with farmers, and key informant interviews with the local agricultural agents from the Koga and Fogera Districts of Amhara Region Ethiopia. The results indicate that irrigation water in general has both direct and indirect positive effects on agriculture, and the indirect effect is mediated by both improved farm inputs and the type of crops produced. The results also show that – due to poor extension services and backward agronomic practices, the mean technical efficiency of farmers in Ethiopia is very low, and that large-scale irrigation users are less technically efficient than small-scale irrigation users. Moreover, the results show that improving irrigation schemes shifts the frontier up, and smallholder farmers are strongly willing to contribute financially to the maintenance costs of irrigation schemes. The results offer relevant lessons for policymakers that providing irrigation water supply must be embedded in a comprehensive support package including access to extension services, improved input supply, and access to stable markets.
Keywords: Doctoral thesis; Economics; Engineering Management (ENM)
|
|
|
“Influence of information provided at the moment of a fire alarm on the choice of exit”. Peeters M, Compernolle T, Van Passel S, Fire Safety Journal 117, 103221 (2020). http://doi.org/10.1016/J.FIRESAF.2020.103221
Abstract: The data generated in buildings are used for all types of purposes. The quality of information used in assisting people to escape an emergency situation is of importance. In practice today, none of the data-generating systems that aid in the escape from emergency situations is validated on a regular basis. This study is based on the smart building concept. The rationale behind this concept is to provide information about a building and the usage of that building at each moment in time. An experiment was conducted to measure the impact of different types of information on participants' choice of exit, exit time and distance travelled. Seven identical floors of one building were used with different setups to see if the choice of exit is influenced by the type of information provided at the moment of an alarm. It was found that the information does have a significant impact on the choice of exit, escape speed and distance travelled. Furthermore, it was shown that false information can increase the time it takes to leave the building and the distance travelled, impacting the survival rate. The more imperative information is visualised, the stronger its influence is on the choices made.
Keywords: A1 Journal article; Economics; Engineering Management (ENM); Center for Oncological Research (CORE)
Impact Factor: 3.1
DOI: 10.1016/J.FIRESAF.2020.103221
|
|
|
“Leasing out unused meeting room capacity to reduce future office space needs : a case study of The Hague, Netherlands”. Peeters M, Compernolle T, Van Passel S, Journal of building engineering 44, 102953 (2021). http://doi.org/10.1016/J.JOBE.2021.102953
Abstract: Meeting rooms are reserved 30% of working hours but only used for 20% of that time. By implementing a strategy where the available capacity is leased to the wider market rather than just the building users, there is a positive impact on the economic, environmental, and social factors of the building and its surroundings. This study uses the building 'The Globe' in The Hague as a case study, and then projects the results to the entire city. In case of The Globe, implementing a lease out strategy achieves a reduction of 36% of the annual rent of the meeting rooms to the building's tenant. The owner benefits from a revenue increase of 12.5%, with the same operational expenses (except the reservation system), leading to a proportional higher valuation of the building. Annual energy consumption may be lowered by 6.2%. This study contributes to the literature by considering the total benefits that could be obtained by more efficient use of office space that is currently underused. The application of technology generates added value for economic, environmental, and social factors. These factors are important in real estate as they (among others) have a direct link to the Environmental, Social and Governance (ESG) analysis that investors make before proceeding with an investment.
Keywords: A1 Journal article; Economics; Engineering sciences. Technology; Economics; Engineering Management (ENM)
DOI: 10.1016/J.JOBE.2021.102953
|
|
|
“Optimal timing of multiple investment decisions in a wood value chain : a real options approach”. Tschulkow M, Compernolle T, Van Passel S, Journal Of Environmental Management 290, 112590 (2021). http://doi.org/10.1016/J.JENVMAN.2021.112590
Abstract: A new reductive catalytic fractionation biorefinery process (RCF) is currently being developed transforming wood into high-value end-products. RCF is considered to be in the pilot stage with a technology readiness level of 5–6. Apart from the RCF-process characteristics, the economic feasibility also depends on the investment decisions that are made upstream and downstream within the wood value chain, increasing the level of uncertainty. Two investment options within the value chain are considered: an option to invest in harvesting equipment and an option to invest in the RCF. To understand the impact of multiple sources of uncertainty on the decision to invest in an innovative RCF-driven wood value chain, an analytical two-factor real options model is presented, accounting for correlated cost and price uncertainties. Two different scenarios, separated and united investments in harvesting equipment and RCF, are analyzed. In both scenarios, market uncertainty postpones investment in comparison to the traditional NPV approach. When both investments are considered separately, the investment in RCF is expected to be earlier than the investment in harvesting equipment. When both investment decisions are united, the probability of investment increases. The study reveals that RCF has the potential to stimulate investments from different investors, –upstream and midstream–, within the wood value chain. Besides, the introduced real options model proofs its ability to assess the economic feasibility of innovative technologies (e.g RCF) individually or within the value chain, taking into account multiple sources of uncertainty.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
Impact Factor: 4.01
DOI: 10.1016/J.JENVMAN.2021.112590
|
|
|
“Rethinking resilient agriculture : from Climate-Smart Agriculture to Vulnerable-Smart Agriculture”. Azadi H, Moghaddam SM, Burkart S, Mahmoudi H, Van Passel S, Kurban A, Lopez-Carr D, Journal Of Cleaner Production 319, 128602 (2021). http://doi.org/10.1016/J.JCLEPRO.2021.128602
Abstract: Climate-Smart Agriculture (CSA) is seeking to overcome the food security problem and develop rural livelihoods while minimizing negative impacts on the environment. However, when such synergies exist, the situation of small-scale farmers is often overlooked, and they are unable to implement new practices and technologies. Therefore, the main aim of this study is to improve CSA by adding the neglected but very important element “small-scale farmer”, and introduce Vulnerable-Smart Agriculture (VSA) as a complete version of CSA. VSA indicates, based on the results of this study, that none of the decisions made by policymakers can be realistic and functional as long as the voice of the farmers influenced by their decisions is not heard. Therefore, to identify different levels for possible interventions and develop VSA monitoring indicators, a new conceptual framework needs to be developed. This study proposed such a framework consisting of five elements: prediction of critical incidents by farmers, measuring the consequences of incidents, identifying farmers' coping strategies, assessing farmers' livelihood capital when facing an incident, and adapting to climate incidents. The primary focus of this study is on farmers' learning and operational preparation to deal with tension and disasters at farm level. Understanding the implications of threats from climate change and the recognizing of coping mechanisms will contribute to an increase in understanding sustainable management.
Keywords: A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM)
Impact Factor: 5.715
DOI: 10.1016/J.JCLEPRO.2021.128602
|
|
|
“Techno-economic assessment of mechanical recycling of challenging post-consumer plastic packaging waste”. Larraín M, Van Passel S, Thomassen G, Van Gorp B, Nhu TT, Huysveld S, Van Geem KM, De Meester S, Billen P, Resources Conservation And Recycling 170, 105607 (2021). http://doi.org/10.1016/J.RESCONREC.2021.105607
Abstract: Increasing plastic recycling rates is crucial to tackle plastic pollution and reduce consumption of fossil resources. Recycling routes for post-consumer plastic fractions that are technologically and economically feasible remain a challenge. Profitable value chains for recycling mixed film and tray-like plastics have hardly been implemented today, in sharp contrast to recycling of relatively pure fractions such as polyethylene terephthalate and high-density polyethylene bottles. This study examines the economic feasibility of implementing mechanical recycling for plastic waste such as polypropylene, polystyrene, polyethylene films and mixed polyolefins. In most European countries these plastic fractions are usually incinerated or landfilled whilst in fact technologies exist to mechanically recycle them into regranulates or regrinds. Results show that the economic incentives for the recycling of plastic packaging depend predominantly on the product price and product yield. At current price levels, the most profitable plastic fraction to be recycled is PS rigids, with an internal rate of return of 14%, whereas the least profitable feed is a mixed polyolefin fraction with a negative internal rate of return in a scenario with steadily rising oil prices. Moreover, these values would be substantially reduced if oil prices, and therefore plastic product prices decrease. Considering a discount rate of 15% for a 15-year period, mechanical recycling is not profitable if no policy changes would be imposed by governments. Clearly low oil prices may jeopardize the mechanical recycling industry, inducing the need for policies that would increase the demand of recycled products such as imposing minimal recycled content targets.
Keywords: A1 Journal article; Economics; Engineering sciences. Technology; Engineering Management (ENM); Intelligence in PRocesses, Advanced Catalysts and Solvents (iPRACS)
Impact Factor: 3.313
DOI: 10.1016/J.RESCONREC.2021.105607
|
|
|
“Adsorption of habitat and industry-relevant molecules on the MoSi₂N₄, monolayer”. Bafekry A, Faraji M, Fadlallah MM, Ziabari AA, Khatibani AB, Feghhi SAH, Ghergherehchi M, Gogova D, Applied Surface Science 564, 150326 (2021). http://doi.org/10.1016/J.APSUSC.2021.150326
Abstract: The adsorption of various environmental gas molecules, including H-2, N-2, CO, CO2, O-2, NO, NO2, SO2 H2O, H2S, NH3 and CH4, on the surface of the recently synthesized two dimensional MoSi2N4 (MSN) monolayer has been investigated by means of spin-polarized first-principles calculations. The most stable adsorption configuration, adsorption energy, and charge transfer have been computed. Due to the weak interaction between molecules studied with the MSN monolayer surface, the adsorption energy is small and does not yield any significant distortion of the MSN lattice, i.e., the interaction between the molecules and MSN monolayer surface is physisorption. We find that all molecules are physisorbed on the MSM surface with small charge transfer, acting as either charge acceptors or donors. The MSN monolayer is a semiconductor with an indirect band gap of 1.79 eV. Our theoretical estimations reveal that upon adsorption of H-2, N-2, CO, CO2, NO, H2O, H2S, NH3 and CH4 molecules, the semiconducting character of MSN monolayer is preserved and the band gap value is decreased to similar to 1.5 eV. However, the electronic properties of the MSN monolayer can be significantly altered by adsorption of O-2, NO and SO2, and a spin polarization with magnetic moments of 2, 1, 2 mu(B), respectively, can be introduced. Furthermore, we demonstrate that the band gap and the magnetic moment of adsorbed MSN monolayer can be significantly modulated by the concentration of NO and SO2 molecules. As the concentration of NO2 molecule increases, the magnetic moment increase from 1 mu(B) to 2 and 3 mu(B). In the case of the SO2 molecule with increasing of concentration, the band gap decreases from 1.2 eV to 1.1 and 0.9 eV. Obviously, our theoretical studies indicate that MSN monolayer-based sensor has a high application potential for O-2, NO, NO2 and SO2 detection.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.387
DOI: 10.1016/J.APSUSC.2021.150326
|
|
|
“Developing feature-rich electronic and magnetic properties in the beta-As monolayer for spintronic and optoelectronic applications by C and Si doping : a first-principles study”. Hoat DM, Duy Khanh Nguyen, Bafekry A, Vo Van On, Ul Haq B, Hoang D-Q, Cocoletzi GH, Rivas-Silva JF, Surfaces and interfaces 27, 101534 (2021). http://doi.org/10.1016/J.SURFIN.2021.101534
Abstract: In this work, the carbon (C) and silicon (Si) doping and codoping effects on beta-arsenene (As) monolayer structural, electronic, and magnetic properties have been comprehensively investigated using first-principles calculations. The studied two-dimensional (2D) materials exhibit good stability. Pristine beta-As single layer is an indirect gap semiconductor with a band gap of 1.867(2.441) eV as determined by PBE(HSE06) functional. Due to the difference in atomic size and electronic interactions, C and Si substitution induces a significant local structural distortion. Depending upon dopant concentration and doping sites, feature-rich electronic properties including non-magnetic semiconductor, magnetic semiconductor and half-metallicity may be obtained, which result from p-p interactions. High spin-polarization at the Fermi level vicinity and significant magnetism suggest As:1C, As:2C, As:1Si, As:2Si, and As:CSi systems as prospective spintronic 2D materials. While, the C-C, Si-Si, and C-Si dimer doping decreases electronic band gap, making the layer more suitable for applications in optoelectronic devices. Results presented herein may suggest an efficient approach to create novel multi-functional 2D materials from beta-As monolayer.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
DOI: 10.1016/J.SURFIN.2021.101534
|
|
|
“Electronic properties of oxidized graphene : effects of strain and an electric field on flat bands and the energy gap”. Alihosseini M, Ghasemi S, Ahmadkhani S, Alidoosti M, Esfahani DN, Peeters FM, Neek-Amal M, The journal of physical chemistry letters (2021). http://doi.org/10.1021/ACS.JPCLETT.1C03286
Abstract: A multiscale modeling and simulation approach, including first-principles calculations, ab initio molecular dynamics simulations, and a tight binding approach, is employed to study band flattening of the electronic band structure of oxidized monolayer graphene. The width offlat bands can be tuned by strain, the external electric field, and the density of functional groups and their distribution. A transition to a conducting state is found for monolayer graphene with impurities when it is subjected to an electric field of similar to 1.0 V/angstrom. Several parallel impurity-induced flat bands appear in the low-energy spectrum of monolayer graphene when the number of epoxy groups is changed. The width of the flat band decreases with an increase in tensile strain but is independent of the electric field strength. Here an alternative and easy route for obtaining band flattening in thermodynamically stable functionalized monolayer graphene is introduced. Our work discloses a new avenue for research on band flattening in monolayer graphene.
Keywords: A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT)
Impact Factor: 9.353
Times cited: 7
DOI: 10.1021/ACS.JPCLETT.1C03286
|
|
|
“First-principles investigation of structural, Raman and electronic characteristics of single layer Ge3N4”. Yayak YO, Sozen Y, Tan F, Gungen D, Gao Q, Kang J, Yagmurcukardes M, Sahin H, Applied surface science 572, 151361 (2022). http://doi.org/10.1016/J.APSUSC.2021.151361
Abstract: By means of density functional theory-based first-principle calculations, the structural, vibrational and electronic properties of single-layer Ge3N4 are investigated. Structural optimizations and phonon band dispersions reveal that single-layer ultrathin form of Ge3N4 possesses a dynamically stable buckled structure with large hexagonal holes. Predicted Raman spectrum of single-layer Ge3N4 indicates that the buckled holey structure of the material exhibits distinctive vibrational features. Electronic band dispersion calculations indicate the indirect band gap semiconducting nature of single-layer Ge3N4. It is also proposed that single-layer Ge3N4 forms type-II vertical heterostructures with various planar and puckered 2D materials except for single-layer GeSe which gives rise to a type-I band alignment. Moreover, the electronic properties of single-layer Ge3N4 are investigated under applied external in-plane strain. It is shown that while the indirect gap behavior of Ge3N4 is unchanged by the applied strain, the energy band gap increases (decreases) with tensile (compressive) strain.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 6.7
DOI: 10.1016/J.APSUSC.2021.151361
|
|
|
“Interface-dependent phononic and optical properties of GeO/MoSO heterostructures”. Yagmurcukardes M, Sozen Y, Baskurt M, Peeters FM, Sahin H, Nanoscale (2021). http://doi.org/10.1039/D1NR06534C
Abstract: The interface-dependent electronic, vibrational, piezoelectric, and optical properties of van der Waals heterobilayers, formed by buckled GeO (b-GeO) and Janus MoSO structures, are investigated by means of first-principles calculations. The electronic band dispersions show that O/Ge and S/O interface formations result in a type-II band alignment with direct and indirect band gaps, respectively. In contrast, O/O and S/Ge interfaces give rise to the formation of a type-I band alignment with an indirect band gap. By considering the Bethe-Salpeter equation (BSE) on top of G(0)W(0) approximation, it is shown that different interfaces can be distinguished from each other by means of the optical absorption spectra as a consequence of the band alignments. Additionally, the low- and high-frequency regimes of the Raman spectra are also different for each interface type. The alignment of the individual dipoles, which is interface-dependent, either weakens or strengthens the net dipole of the heterobilayers and results in tunable piezoelectric coefficients. The results indicate that the possible heterobilayers of b-GeO/MoSO asymmetric structures possess various electronic, optical, and piezoelectric properties arising from the different interface formations and can be distinguished by means of various spectroscopic techniques.
Keywords: A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT)
Impact Factor: 7.367
Times cited: 5
DOI: 10.1039/D1NR06534C
|
|
|
“Novel two-dimensional ZnO₂, CdO₂, and HgO₂, monolayers: a first-principles-based prediction”. Faraji M, Bafekry A, Gogova D, Hoat DM, Ghergherehchi M, Chuong NV, Feghhi SAH, New Journal Of Chemistry 45, 9368 (2021). http://doi.org/10.1039/D1NJ01610E
Abstract: In this paper, the existence of monolayers with the chemical formula XO2, where X = Zn, Cd, and Hg with hexagonal and tetragonal lattice structures is theoretically predicted by means of first principles calculations. Through cohesive energy calculation and phonon dispersion simulation, it has been proven that the two-dimensional XO2 monolayers proposed are energetically and dynamically stable suggesting their potential experimental realization. Our detailed study demonstrates that these novel newly predicted materials are half-metals and dilute magnetic semiconductors, and they exhibit magnetism in the ground state. The half-metallic character could find many applications in electronic and spintronic devices. Research into the magnetic properties revealed here can enrich theoretical knowledge in this area and provide more potential candidates for XO2 2D-based materials and van der Waals heterostructures.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 3.269
DOI: 10.1039/D1NJ01610E
|
|
|
“Quasiparticle twist dynamics in non-symmorphic materials”. Juneja R, Thebaud S, Pandey T, Polanco CA, Moseley DH, Manley ME, Cheng YQ, Winn B, Abernathy DL, Hermann RP, Lindsay L, Materials Today Physics 21, 100548 (2021). http://doi.org/10.1016/J.MTPHYS.2021.100548
Abstract: Quasiparticle physics underlies our understanding of the microscopic dynamical behaviors of materials that govern a vast array of properties, including structural stability, excited states and interactions, dynamical structure factors, and electron and phonon conductivities. Thus, understanding band structures and quasiparticle interactions is foundational to the study of condensed matter. Here we advance a 'twist' dynamical description of quasiparticles (including phonons and Bloch electrons) in nonsymmorphic chiral and achiral materials. Such materials often have structural complexity, strong thermal resistance, and efficient thermoelectric performance for waste heat capture and clean refrigeration technologies. The twist dynamics presented here provides a novel perspective of quasiparticle behaviors in such complex materials, in particular highlighting how non-symmorphic symmetries determine band crossings and anti-crossings, topological behaviors, quasiparticle interactions that govern transport, and observables in scattering experiments. We provide specific context via neutron scattering measurements and first-principles calculations of phonons and electrons in chiral tellurium dioxide. Building twist symmetries into the quasiparticle dynamics of non-symmorphic materials offers intuition into quasi particle behaviors, materials properties, and guides improved experimental designs to probe them. More specifically, insights into the phonon and electron quasiparticle physics presented here will enable materials design strategies to control interactions and transport for enhanced thermoelectric and thermal management applications. (C) 2021 Published by Elsevier Ltd.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
DOI: 10.1016/J.MTPHYS.2021.100548
|
|
|
“Strain-driven modulation of the electronic, optical and thermoelectric properties of beta-antimonene monolayer : a hybrid functional study”. Hoat DM, Nguyen DK, Bafekry A, Van On V, Ul Haq B, Rivas-Silva JF, Cocoletzi GH, Materials Science In Semiconductor Processing 131, 105878 (2021). http://doi.org/10.1016/J.MSSP.2021.105878
Abstract: Electronic, optical, and thermoelectric properties of the beta-antimonene (beta-Sb) monolayer under the external biaxial strain effects are fully investigated through the first-principles calculations. The studied two-dimensional (2D) system is dynamically and structurally stable as examined via phonon spectrum and cohesive energy. At equilibrium, the beta-Sb single layer exhibits an indirect band gap of 1.310 and 1.786 eV as predicted by the PBE and HSE06 functionals, respectively. Applying external strain may induce the indirect-direct gap transition and significant variation of the energy gap. The calculated optical spectra indicate the enhancement of the optical absorption in a wide energy range from infrared to ultraviolet as induced by the applied strain. In the visible and ultraviolet regime, the absorption coefficient can reach values as large as 82.700 (10(4)/cm) and 91.458 (10(4)/cm). Results suggest that the thermoelectric performance may be improved considerably by applying proper external strain with the figure of merit reaching a value of 0.665. Our work demonstrates that the external biaxial strains may be an effective method to make the beta-Sb monolayer prospective 2D material for optoelectronic and thermoelectric applications.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.359
DOI: 10.1016/J.MSSP.2021.105878
|
|