Abstract: The rise in plastic packaging production and disposal has encouraged the progress of recycling technologies and aroused policy discussion on how to increase recycling rates. However, the effect that these policy instruments will have on the development of the different recycling technologies has not been studied holistically yet. This dissertation explores how new and existing technologies will behave under the market and policy conditions observed at present and after the implementation of the policy instruments that are under discussion. The technologies that are analyzed in this thesis are mechanical recycling and thermochemical recycling of post-consumer polyolefin waste. Using a techno-economic assessment that takes into account the physical properties of the different plastic fractions and their contamination level, the study shows that both mechanical and thermochemical recycling can be profitable if oil prices remain steady or increase. Specifically, mechanical recycling will show better results than thermochemical recycling for plastic fractions with low contamination levels. On the contrary, thermochemical recycling is more profitable for fractions with a higher contamination level from which high-quality products cannot be obtained with mechanical recycling, such as PE films. Moreover, it demonstrates that besides the oil prices and sorted waste prices, waste purity and the plant capacity are the variables that influence more the net present value of thermochemical recycling and the labor cost and waste purity the ones of mechanical recycling. The thesis explores the dynamics between the stakeholders of the circular value chain and predicts the recycling rates under the implementation of several policy instruments. This is done with a supply chain equilibrium model, based on the extended producer responsibility scheme implemented in Flanders, that uses as an input the cost structures of mechanical and thermochemical recycling obtained from the techno-economic assessments. Direct interventions like recycled content standards, can decouple the recycling industry from the oil market, but in the long term, they may not present incentives to achieve recycling levels beyond the targeted amounts and thus limit technological innovation. On the contrary, economic interventions such as taxes, create economic incentives for recycling and allow fund collection from the government but leave the recycled levels dependent on external markets. Results also show that higher recycling rates does not necessarily mean better environmental performance. Therefore, when designing circular economy policies, policymakers should carefully analyze whether the intention is to increase circularity or improve the sustainability of the value chains.

Abstract: Novel emerging biorefinery technologies have gained interest and have the potential to tackle several sustainability challenges in our society. A lignin-first biorefinery process – reductive catalytic fractionation (RCF) – is currently under development with the aim to process wood into high-value end-products that replace highly polluting fossil oil-based products. However, such emerging technologies are not matured yet, holding a certain degree of technological, economic, and environmental uncertainty. Hence, an appropriate assessment method is required to assess techno-economic feasibility and environmental impacts of emerging uncertain technologies (e.g lignin-first RCF process). This dissertation aims to develop an integrated techno-environmental economic assessment framework to assess emerging technologies dynamically and prospectively from economic and environmental points of view. First, a techno-economic assessment (TEA) is performed to assess the economic feasibility and the most influential economic and technological parameters of the lignin-first RCF biorefinery taking the whole wood value chain into account. By making the relations across the wood value chain, the scale of the biorefinery, wood species, and output prices highly determine the economic feasibility. The economic feasibility can be reached by a sufficient capacity level which depends on wood species-specific conditions. Also, waste wood proves to be the most profitable feedstock in comparison to virgin wood. Second, an analytical real options analysis (ROA) is performed taking two correlated market uncertainties and the value of flexibility into account to identify the optimal investment decision in an RCF biorefinery. Two different investment options, separated and united investments in harvesting equipment and RCF biorefinery, are analyzed. In both scenarios, market uncertainty postpones the investment. When both investment decisions are united, the probability of investment increases in comparison to separated investments. The study reveals that RCF has the potential to stimulate investments within the wood value chain. Third, a consequential life cycle assessment (LCA) is performed to assess the carbon emissions and the environmental consequences of the lignin-first RCF process and its products. The study reveals that at the current stage RCF products have higher carbon emissions than their alternative counterparts. Several options to improve the environmental performance are discussed such as different RCF technology configurations, targeting different RCF products with the ability to replace higher polluting alternative counterparts on the markets. Other discussion points such as transportation type and the distance, (in-)direct land-use change, the use stage and disposal stages implications, and a more comprehensive environmental view of the RCF products, show the potential to improve the environmental performance of the RCF technology. Overall, the study shows that the RCF process can be environmentally desirable if the appropriate RCF configuration and products are chosen. Finally, the above-mentioned methods – techno-economic assessment, analytical real options analysis, and consequential life cycle assessment – are uniquely integrated within the newly developed integrated assessment framework. The framework has the aim to complement the shortcomings and combine the advantages of all three methods. The framework assesses emerging technologies to give predictive insights about the time-specific economic and environmental performance under the newly developed three threshold conditions: technological readiness, economic feasibility, and environmental desirability. The developed integrated assessment framework assesses dynamically and prospectively the RCF biorefinery implementation under Belgian conditions. It reveals that the economic feasibility increases and carbon emissions decrease over time. The RCF biorefinery fulfills all three threshold conditions – technological readiness, economic feasibility, and environmental desirability – consecutively. The newly developed integrated assessment framework offers decision support to several stakeholders of emerging technologies starting from low technology readiness level (TRL). Practitioners such as the technology developers, researchers, and policymakers can use the framework to evaluate emerging technologies that deal with high levels of technological, economic, and environmental uncertainties. The framework assesses emerging technologies on a detailed level to give decision-makers in-depth insights into the intertwined nature of the technological, economic, and environmental dimensions. It offers insights into the expected time-specific economic and environmental performances, potential, and challenges of the emerging technology to further improve the technology and direct R&Ds along the right path.

Abstract: Being confronted with increasing and expanding urbanisation and the loss of natural green spaces, our living environment is threatened more and more by the effects of global climate change. Green infrastructure is often thought of as the solution to increase climate resilience and reinforce the quality of the lived environment simultaneously. While the benefits, or ecosystem services, that are generated through green infrastructure have been studied intensively, forces that influence green infrastructure decision-making have been far less subjected to thorough research. In this study a discrete choice experiment was conducted with local decision makers in Flemish municipalities to reveal crucial factors in the decision process applied to green infrastructure projects. Flanders is one of the most densely built regions in Europe, stressing the urgency to understand local spatial decision factors to guarantee green space. 568 decision makers active in the local administration of 235 Flemish municipalities participated in the experiment, set in a hypothetical neighbourhood park. Every choice alternative exists of five attributes: investment cost, maintenance cost, deferred investment, recreational value, and climate impact. We find that barriers hampering Flemish munipalities' GI implementation, differ over size of the municipality: smallers municipalities are more affected by knowledge gaps, while larger municipalities are experiencing prioritization issues. Results from hierarchical Bayes choice models indicate that municipal decisions on green infrastructure are highly – almost solely -cost-driven, rarely consider the full range of benefits, and centre around short-term and immediate arguments. Moreover, interaction models reveal that a municipalities' financial result is a key determinant of its willingness to invest in public greening and consider long term benefits, suggesting that GI is a luxury good. The results expose some of the heuristics in GI decision making and can be used to inform higher authorities on ways to overcome barriers towards informed decision-making and to facilitate GI investment.

Abstract: Three-dimensional (3D) computational fluid dynamics (CFD) simulations were performed to study solids flow dynamics and solids back-mixing behavior in a screw reactor (designed for thermal conversion of dry biomass particles) based on the Eulerian-Eulerian method. Simulation results were compared against experimental data with respect to filling degree and mean residence time of particles. The mean deviations for filling degree and for mean residence time between simulation and experiment were about 0.01 and 11.4 s, respectively, which shows that the model is reasonably accurate in predicting solids flow behavior in the screw reactor. The solids flow dynamics inside the reactor were discussed. The solids residence time distribution (RTD) was calculated and the degree of solids back-mixing in the forward transportation direction of the reactor was analyzed. It was found that solids being flung over the shaft and solids back-leakage, resulting from the low solids forward transportation velocity at the clearance between the flight and the bottom shell of the screw reactor, were responsible for solids back-mixing. The degree of solids back-mixing can be reduced at higher screw rotating speeds when keeping inlet mass flow rate of solids constant. (C) 2019 Elsevier Ltd. All rights reserved.

Abstract: Large river catchments with mixed land use capture pesticides from many sources, and degradable pesticides are converted during downstream transport. Unravelling the contribution of pesticide source and the effect of degradation processes is a challenge in such areas. However, insight and understanding of the sources is important for targeted managen-lent, especially when water is abstracted from the river for drinking water production. The river Meuse is such a case. A long-term monitoring data set was applied in a modelling approach for assessing the contribution of waste water treatment plants (WWTPs) and tributaries (sub-basins) to surface water contamination, and to evaluate the effect of decay on the downstream concentrations of glyphosate and AMPA at the point of drinking water abstraction. The results show that WWTPs are important contributors for glyphosate and AMPA in large river catchments with mixed land uses. In the studied area, the river Meuse in the Netherlands, the relative contribution of WWTP effluents is above 29% for glyphosate and around 12% for AMPA. Local industries are found to be potentially big contributors of AMPA. Glyphosate entering the river system is gradually converted to AMPA and other degradation-productions, which results in downstream loads that are considerably lower than the sum of all influxes. In summer when the travel time is longer due to lower discharge, the first order decay of glyphosate in the river Meuse is estimated to result in about 50% reduction of the downstream glyphosate concentrations over a river stretch of 250 km. The contribution of glyphosate decay to the observed AMPA concentrations ranges between 2% and 10%. Contributions are sensitive to seasonal variations in discharge that influence the concentrations through dilution and degradation. (C) 2016 Elsevier B.V. All rights reserved.

Abstract: EU strategies for waste management have long recognized the key role of recycling to move towards sustainable consumption and production. This resulted in a range of regulatory measures, among which the Waste Electrical and Electronic Equipment (WEEE) directive, which sets weight-based targets for recovery, preparation for re-use and recycling. The increasing strategic relevance of the supply of raw materials has, however, spurred a more integrated approach towards resource efficiency. In addition to the prevention of disposal, recycling practices are now also meant to contribute to sustainable materials management by pursuing (i) a higher degree of material cycle closure, (ii) an improved recovery of strategically relevant materials, and (iii) the avoidance of environmental burdens associated with the extraction and refining of primary raw materials. In response to this evolution, this paper reports about the development of an indicator set that allows to quantitatively demonstrate these recycling benefits, hence going further than the weight-based objectives employed in the WEEE directive. The indicators can be calculated for WEEE recycling processes for which information is available on both input and output fractions. It offers a comprehensive framework that aims to support decision making processes on product design, to identify opportunities for the optimization of WEEE End-of-Life scenarios, and to assess the achieved (or expected) results of implemented (or planned) recycling optimization strategies. The paper is illustrated by a case study on the recycling of LCD televisions. (C) 2014 Elsevier Ltd. All rights reserved.

Abstract: We present a computational model to model the magnetic structure of two-dimensional (2D) dilute-magnetic-semiconductors (DMS) both the monolayers and multilayers using first-principles density functional theory (DFT), as well as their magnetic phase transition as a function of temperature using Monte-Carlo simulations. Using our method, we model the magnetic structure of bulk, bilayer, and monolayer MoS2 substitutionally doped with Fe atoms. We find that the out-of-plane interaction in bilayer MoS2 is weakly ferromagnetic, whereas in bulk MoS2 it is strongly anti-ferromagnetic. Finally, we show that the magnetic order is more robust in bilayer Fe-doped MoS2 compared to the monolayer and results in a room-temperature FM at an atomic substitution of 14-16%.

Abstract: The latest life-cycle assessment methods account for land use, due to the production, use and disposal of products and services, in terms of ecosystem damage. The process of brownfield remediation converts otherwise idle urban space into productive space. The value to ecosystems in this context is of course limited since the brownfield site remains urban. When evaluating brownfield remediation technologies, the availability of space on-site is dependent on the duration of time required by the remediation technology to reach the remediation target. Remediation technology alternatives tend to vary largely in terms of duration. Comparative life-cycle assessments of remediation technologies, to date, present the large variations between alternatives in terms of remediation duration but do not translate this into an impact or parameter. The restored subsurface zone is often defined as a functional unit, when in fact the surface area is the resource restored by the remediation service. The economic benefits of making land resources available are particularly important considerations in the context of brownfield remediation. The research proposes an innovative impact assessment approach that allows land to be considered as a finite resource. The method is applied in a comparative life-cycle assessment of two potential remediation scenarios for an idle brownfield in the Brussels region of Belgium. The results show that there is a trade-off between greenhouse gas emissions and land availability and that both are largely dependent on the efficiency of the contaminant extraction mechanism. The results also raise the question as to whether the economic valuation of land, like precious metals and fossil fuels, provides an accurate reflection of the true value of the resource. Considering land as a resource at the midpoint level is also relevant in other urban contexts where competition exists between different land-uses, where urban sprawl is detrimental to undeveloped areas and where urban intensification is a policy objective. (C) 2015 Elsevier Ltd. All rights reserved.

Abstract: An increased pulse pressure (difference between systolic and diastolic blood pressure) suggests aortic stiffening. The objective of this study was to examine the acute effects of both particulate matter (PM) mass and composition on blood pressure, among elderly persons. We carried out a panel study in persons living in elderly homes in Antwerp, Belgium. We recruited 88 non-smoking persons, 70% women with a mean age of 83 years (standard deviation: 5.2). Blood pressure was measured and a blood sample was collected on two time points, which were chosen so that there was an exposure contrast in ambient PM exposure. The elemental content of the collected indoor and outdoor PM2.5 (particulate matter with an aerodynamic diameter <2.5 μm) mass concentration was measured. Oxygenated polycyclic aromatic hydrocarbons (oxy-PAHs) on outdoor PM10 (particulate matter with an aerodynamic diameter <10 μm) were measured. Each interquartile range increase of 20.8 μg/m³ in 24-h mean outdoor PM2.5 was associated with an increase in pulse pressure of 4.0 mmHg (95% confidence interval: 1.86.2), in persons taking antihypertensive medication (n=57), but not in persons not using antihypertensive medication (n=31) (p for interaction: 0.02). Vanadium, iron and nickel contents of PM2.5 were significantly associated with systolic blood pressure and pulse pressure, among persons on antihypertensive medication. Similar results were found for indoor concentrations. Of the oxy-PAHs, chrysene-5,6-dione and benzo[a]pyrene-3,6-dione were significantly associated with increases in systolic blood pressure and pulse pressure. In elderly, pulse pressure was positively associated with acute increases in outdoor and indoor air pollution, among persons taking antihypertensive medication. These results might form a mechanistic pathway linking air pollution as a trigger of cardiovascular events.

Abstract: The installation of urban green infrastructure, particularly green walls, has proven to be an effective strategy for the mitigation of particulate matter (PM) pollution and the urban heat island effect. For the interaction between vegetation, PM and the local microclimate, wind flow is the main driving force. In order to investigate these interactions in detail, it is important to know how air flows through vegetation. This study proposes a method based on the DarcyForchheimer equation, where vegetation is considered as a porous medium and several plant species and the effects of plant morphological characteristics are examined both experimentally and using computer simulations. Results showed that the DarcyForchheimer model is a simple and robust way to describe air flow through vegetation regardless of its morphology. This research provides a new vision on studying aerodynamic properties of vegetation in relation to their morphology and provides opportunities for model the interaction between vegetation and its environment.

Abstract: Different trace- and microanalytical techniques were used in an extensive study to elucidate the chemical deterioration process of the sandy-limestone St Rombouts Cathedral in Mechelen, Belgium. Samples of stones, mortar joints, slates, atmospheric aerosols and gases, total and wet deposition, and water that had run down the cathedral walls, were all thoroughly characterized. At the east side, usually not exposed to precipitation, a 3001000-μm thick outer crust of microcrystalline gypsum was observed, while at the west side, this surface layer was mostly eroded away due to precipitation. At the north and south sides, the crust contains varying amounts of gypsum and calcite. The gypsum is mostly present in a bar-shaped morphology and carbonaceous fly-ash particles were rarely found in the weathering crust. Local stone characteristics seem to be extremely important in relation to the gypsum content of the crust; black samples always have a much higher sulphate content than the corresponding white samples, irrespective of the predominant direction of orientation. The relative contribution of nitrogen- and chlorine-containing pollutants to the total decay process is much smaller than that of sulphur-containing pollutants. Deposition samples collected at the site of the cathedral mostly had a pH of > 5.6, due to the neutralization of the rainwater by alkaline atmospheric constituents. Runoff water and washdown water were enriched in all ions, especially Ca2+ and SO42−, indicating that, indeed, gypsum is the most important weathering product. The suspension in deposition samples and black-well leaching water was highly enriched in silicon-containing particles, while runoff water and white-wall leaching water contained a predominant calcium-rich suspension.