Abstract: Single-atom catalysts (SACs) have recently attracted broad scientific interests due to their unique structural feature, the single-atom dispersion. Optimized electronic structure as well as high stability are required for single-atom catalysts to enable efficient electrochemical production of H2O2. Herein, we report a facile synthesis method that stabilizes atomic Pd species on the reduced graphene oxide/Ndoped carbon hollow carbon nanospheres (Pd1/N-C). Pd1/N-C exhibited remarkable electrochemical H2O2 production rate with high faradaic efficiency, reaching 80%. The single-atom structure and its high H2O2 production rate were maintained even after 10,000 cycle stability test. The existence of single-atom Pd as well as its coordination with N species is responsible for its high activity, selectivity, and stability. The N coordination number and substrate doping around Pd atoms are found to be critical for an optimized adsorption energy of intermediate *OOH, resulting in efficient electrochemical H2O2 production. (C) 2020 Elsevier Inc. All rights reserved.

Abstract: As narrow band gap nanocrystals become a considerable building block for the design of infrared sensors, device design needs to match their actual operating conditions. While in the near and shortwave infrared, room-temperature operation has been demonstrated, longer wavelengths still require low-temperature operations and thus specific design. Here, we discuss how field-effect transistors (FETs) can be compatible with low-temperature detection. To reach this goal, two key developments are proposed. First, we report the gating of nanocrystal films from SrTiO3 which leads to high gate capacitance with leakage and breakdown free operation in the 4-100 K range. Second, we demonstrate that this FET is compatible with a plasmonic resonator whose role is to achieve strong light absorption from a thin film used as the channel of the FET. Combining three resonances, broadband absorption from 1.5 to 3 mu m reaching 30% is demonstrated. Finally, combining gate and enhanced light-matter coupling, we show that detectivity can be as high as 10(12) Jones for a device presenting a 3 mu m cutoff wavelength and 30 K operation.

Abstract: In the past decade, to improve crop production and productivity, Ethiopia has embarked on an ambitious irrigation farming expansion program and has introduced new large- and small-scale irrigation initiatives. However, in Ethiopia, poverty remains a challenge, and crop productivity per unit area of land is very low. Literature on the technical efficiency (TE) of large-scale and small-scale irrigation user farmers as compared to the non-user farmers in Ethiopia is also limited. Investigating smallholder farmers' TE level and its principal determinants is very important to increase crop production and productivity and to improve smallholder farmers' livelihood and food security. Using 1026 household-level cross-section data, this study adopts a technology flexible stochastic frontier approach to examine agricultural TE of large-scale irrigation users, small-scale irrigation users and non-user farmers in Ethiopia. The results indicate that, due to poor extension services and old-style agronomic practices, the mean TE of farmers is very low (44.33%), implying that there is a wider room for increasing crop production in the study areas through increasing the TE of smallholder farmers without additional investment in novel agricultural technologies. Results also show that large-scale irrigation user farmers (21.05%) are less technically efficient than small-scale irrigation user farmers (60.29%). However, improving irrigation infrastructure shifts the frontier up and has a positive impact on smallholder farmers' output.

Abstract: Numerous applications have required the study of CO2 plasmas since the 1960s, from CO2 lasers to spacecraft heat shields. However, in recent years, intense research activities on the subject have restarted because of environmental problems associated with CO2 emissions. The present review provides a synthesis of the current state of knowledge on the physical chemistry of cold CO2 plasmas. In particular, the different modeling approaches implemented to address specific aspects of CO2 plasmas are presented. Throughout the paper, the importance of conducting joint experimental, theoretical and modeling studies to elucidate the complex couplings at play in CO2 plasmas is emphasized. Therefore, the experimental data that are likely to bring relevant constraints to the different modeling approaches are first reviewed. Second, the calculation of some key elementary processes obtained with semi-empirical, classical and quantum methods is presented. In order to describe the electron kinetics, the latest coherent sets of cross section satisfying the constraints of “electron swarm” analyses are introduced, and the need for self-consistent calculations for determining accurate electron energy distribution function (EEDF) is evidenced. The main findings of the latest zero-dimensional (0D) global models about the complex chemistry of CO2 and its dissociation products in different plasma discharges are then given, and full state-to-state (STS) models of only the vibrational-dissociation kinetics developed for studies of spacecraft shields are described. Finally, two important points for all applications using CO2 containing plasma are discussed: the role of surfaces in contact with the plasma, and the need for 2D/3D models to capture the main features of complex reactor geometries including effects induced by fluid dynamics on the plasma properties. In addition to bringing together the latest advances in the description of CO2 non-equilibrium plasmas, the results presented here also highlight the fundamental data that are still missing and the possible routes that still need to be investigated.

Abstract: Aptamers are short, synthetic DNA or RNA molecules that are characterized by a specific 3D conformation which enables specific target recognition. Aptamers are promising tools in many application fields from sensing to therapeutics. One of the major challenges in the aptamer field is understanding the relationship between the sequence and what determines the higher-order structure and specific interactions with targets. Therefore, this PhD thesis focuses on the use of different mass spectrometry (MS) based approaches to characterize aptamers and their interactions. Several of these approaches are already widely applied to study other biomolecules, such as proteins, but are still largely unexplored for aptamers and oligonucleotides in general. A first focus was put on obtaining information on the higher-order structure and conformational stability of aptamers using a combination of MS and with ion mobility (IM) spectrometry by performing collision-induced unfolding (CIU) experiments. CIU was shown to hold great promise to analyze the conformational dynamics and gas-phase stabilities of aptamers. Next, the capabilities and limitations of native IM-MS for the analysis of noncovalent interactions of aptamers were demonstrated. The conformational behavior and interactions of cocaine-binding aptamers were studied and it was found that relative binding affinities of aptamers that only differ slightly in sequence and structure can be determined using native MS. Moreover, native IM-MS allowed the detection of small conformational changes upon binding of a target, which were found to be dependent on the binding mode of the aptamer. An adaptive binding mechanism was suggested for flexible aptamers that require more reorganization upon binding. In the final part of this thesis, the importance of thoroughly characterizing and validating aptamer-target interactions before using them in an application was emphasized. Moreover, the gathered insights were applied in our own development of a proof-of-concept aptamer-based sensor. This was shown by investigating the interactions of ampicillin aptamers which were found to not bind the target they were selected for in the first place. A multi-analytical approach combining complementary techniques was used for this purpose since no single technique is generally applicable to characterize all aptamers and their interactions and to obtain a comprehensive picture of the aptamer-target interactions. Furthermore, such multi-analytical approach was used to characterize a testosterone-binding aptamer while developing an aptamer-based electrochemiluminescent sensing strategy for this target. This shows the importance of native MS, in combination with other techniques, to thoroughly understand the aptamer-target interactions in the development of a designed application.

Abstract: This thesis presents, in its first part, an investigation on the trembling motion of wave packets known as zitterbewegung (ZBW), in multilayer graphene, as well as in moiré excitons in twisted MoS2/WSe2 hetero-bilayers. In the last few decades, the dynamics of wave packets has been subject of many theoretical and experimental studies in various types of systems such as semiconductors, superconductors, crystalline solids and cold atoms. The discovery of graphene and moiré excitons in twisted hetero-bilayers, brought two new platforms for the investigation on time evolution of wave packets and possible observation of ZBW. This trembling motion was first theoretically predicted by Schrödinger for wave packets describing particles that obey the Dirac equation. This is exactly the case of low energy electrons in graphene, as well as of moiré exciton in twisted MoS2/WSe2 under an external applied electromagnetic field. ZBW in multilayer graphene was studied both analytically and computationally, respectively, through the Green's function and split-operator methods. In this system, it is found that ZBW depends not only on the wave packet width and initial pseudospin polarization, but also on the number of layers. Furthermore, the analytical and numerical methods proposed here allow to investigate wave packet dynamics in graphene systems with an arbitrary number of layers and arbitrary potential landscapes. For moiré excitons in twisted MoS2/WSe2 hetero-bilayers, it is shown that, analogously to other Dirac-like particles, this system also exhibits ZBW when under a perpendicular applied field. In this case, the ZBW presents long timescales that are compatible with current experimental techniques for exciton dynamics. This promotes the study of the dynamics of moiré excitons in van der Waals heterostructures as an advantageous solidstate platform to probe zitterbewegung, broadly tunable by gating and inter-layer twist angle. In the second part of this thesis, a study into graphene plasmonic in van der Waals heterostructure (vdWhs) are treated in a linear response framework within the Random Phase Approximation and with support of the quantum electrostatic heterostructure (QEH), a DFT-based method. Since Dirac plasmons in graphene are very sensitive to the dielectric properties of the environment, it is possible to explore this property to probe the structure and composition of van der Waals heterostructures (vdWh) placed underneath a single graphene layer. In this way, one can achieve a layer sensitivity of a single layer and differentiate between different TMDs for heterostructures thicker than 2 layers. As a consequence of this, study, the hybridization of Dirac plasmons in graphene with phonons of transition metal dichalcogenides (TMDs), when the materials are combined in so-called van der Waals heterostructures (vdWh) forming surface plasmon-phonon polaritons (SPPPs) are also investigated. It was found that it is possible to realize both strong and ultrastrong coupling regimes by tuning graphene’s Fermi energy and changing TMD layer number.

Abstract: One of the main objectives of implementing a circular economy system is the reuse and recycling of resources. Closing material cycles and renewable-based electricity and fuel production are essential to such systems. To achieve a high degree of circularity, waste streams have to be rethought and integrated from a cradle-to-grave to a cradle-to-cradle approach. However, today’s circular economy strategies mostly focus on current waste streams, while past waste streams, buried in landfills, could play an important role when recovering resources and energy. Hence, a well-thought-out circular economy strategy should include the re-integration of past waste streams. A grave-to-cradle approach is needed. Landfill mining (LFM), i.e. the excavation and processing of formerly buried waste to energy and materials, aims at utilizing these past waste streams. Doing so could bear potential economic, environmental, and societal burdens and benefits. Originating from landfill remediation projects, landfill mining has been further developed towards resource recovery. Today, using up-to-date technologies and following the most stringent environmental and social criteria, the concept is also known as enhanced landfill mining (ELFM). Throughout the relevant scientific literature, most attention is given to advances in technological development for (E)LFM, as well as its techno-economic and environmental assessment. Societal assessments of LFM projects are rare and treat societal impacts only selectively or from unilateral societal perspectives. If stakeholders are included in societal (E)LFM assessments, only industrial actors, like landfill operators, and governmental actors are asked to participate. A holistic stakeholder assessment for (E)LFM is missing. Moreover, the diverse societal impacts – ranging from socio-environmental benefits through the mitigation of health risks, over socio-economic benefits through land reclamation, and social benefits through community engagement, for example – are either only studied selectively or evaluated as one, entangling various societal effects. A holistic and specific assessment of societal factors affecting (E)LFM implementation is also missing. This thesis uses an anticipatory approach to tackle these challenges. This approach aims to integrate stakeholder values and include uncertainty through the use of multiple social perspectives and prospective modeling tools. In-depth interviews were conducted to develop a typology of (E)LFM stakeholders and to elicit the most important stakeholder needs. Stakeholders were selected along an extended quadruple helix framework, including industrial, institutional, scientific, and community actors. Furthermore, using system dynamics tools, namely causal loop diagrams, societal systems of (E)LFM could be visualized and analyzed. Finally, a discrete choice experiment was conducted to evaluate a set of societal factors representing the conversion of a landfill into a public park for recreational use. The in-depth interviews included landfill operators, technology providers and incubators, local governments and governmental institutions, as well as researchers and community members. To structure the diverse perspectives of stakeholders on (E)LFM, five stakeholder archetypes were developed: The Entrepreneur, the Engaged Citizen, the Visionary, the Technology Enthusiast, and the Skeptic. The archetypes capture important characteristics and opinions approaching (E)LFM implementation. They differ in risk perceptions, knowledge base, influence on (E)LFM’s systemic and project implementation, and their main concerns and motivations. Furthermore, 18 stakeholder needs were derived from the interviews. This includes societal, environmental, regulatory, and techno-economic needs. The needs are put in relation to the affected stakeholders and sustainability dimensions. Uncertainties that could potentially be reduced through the fulfillment of each need are qualitatively assessed. Quantitatively, stakeholders were focusing on societal, regulatory, and techno-economic needs, whereas qualitative emphasis was given to environmental needs, especially the avoidance of impacts from primary resource production. When meeting stakeholder needs fairly, intra- and inter-dimensional trade-offs have to be considered as different perspectives can lead to different and sometimes contradicting implications for (E)LFM implementation. To conceptualize societal systems of (E)LFM, causal loop diagrams were developed following system dynamics methodology. The visualizations show how (E)LFM is embedded in its societal context. Variables comprising the societal impact were analyzed, and mechanisms affecting the public project acceptance and the market acceptance of (E)LFM products worked out. Leverage points were identified, helping (E)LFM practitioners and policymakers to minimize potential risks and maximize potential benefits. To these count technological choices, stakeholder involvement, the after-use, quality standards, and LFM regulation in general, amongst others. To disentangle and evaluate societal impacts of (E)LFM, a discrete choice experiment was conducted deriving the utility of five distinct attributes: the size of a landfill, the project duration, job creation, disamenities, and climate impacts. To determine the willingness to pay, perform scenario analysis, and model policy simulations, a sixth attribute was added representing a cost factor for project implementation. Environmental considerations are most important to the sample, while project duration and disamenities also play a significant role. The scenario analysis and policy simulations show that taxing households for (E)LFM implementation is a viable option, especially for environmentally beneficial projects. Nonetheless, a favorable combination of the remaining attributes can compensate utility losses for environmentally questionable projects. As risks of classical landfill management practices are likely to grow with an updated evaluation of after-care periods lasting up to 100 years and more, positive effects of (E)LFM become even more noteworthy. Nonetheless, (E)LFM projects also pose potential risks like groundwater contamination or the reintroduction of hazardous materials. If executed poorly, (E)LFM projects could potentially do more harm than good. A mix of policy measures is recommended to push a major part of potential (E)LFM projects from being environmentally beneficial and economically inefficient to being societally, environmentally, and economically favorable. Overall, more research is necessary to integrate (E)LFM into circular economy strategies and build a sensible grave-to-cradle approach.

Abstract: Electron microscopy is an excellent tool which provides resolution down to the atomic scale with up to pm precision in locating atoms. The characterization of materials in these length scales is of utmost importance to answer questions in biology, chemistry and material science. The successful implementation of aberration-corrected microscopes made atomic resolution imaging relatively easy, this could give the impression that the development of novel electron microscopy techniques would stagnate and only the application of these instruments as giant magnifying tools would continue. This is of course not true and a multitude of problems still exist in electron microscopy. Two of such issues are discussed below. One of the biggest problems in electron microscopy is the presence of beam damage which occurs due the fact that the highly energetic incoming electrons have sufficient kinetic energy to change the structure of the material. The amount of damage induced depends on the dose, hence minimizing this dose during an experiment is beneficial. This minimizing of the total dose comes at the expense of more noise due to the counting nature of the electrons. For this reason, the implementation of four dimensional scanning transmission electron microscopy (4D STEM) experiments has reduced the total dose needed per acquisition. However, the current cameras used to measure the diffraction patterns are still two orders of magnitude slower than to the conventional STEM methods. Improving the acquisition speed would make the 4D STEM technique more feasible and is of utmost importance for the beam sensitive materials since less dose is used during the acquisition. In TEM there is not only the possibility to perform imaging experiments but also spectroscopic measurements. There are two frequently used methods: electron energy-loss spectroscopy (EELS) and energy dispersive x-ray spectroscopy (EDX). EELS measures the energy-loss spectrum of the incoming electron which gives information on the available excitations in the material providing elemental sensitivity. In EDX, the characteristic x-rays, arising from the decay of an atom which is initially excited due to the incoming electrons, are detected providing similar elemental analysis. Both methods are able to provide comparable elemental information where in certain circumstances one outperforms the other. However, both methods have a detection limit of approximately 100-1000 ppm which is not sufficient for some materials. In this thesis, two novel techniques which can make significant progress for the two problems discussed above.

Abstract: The wide array of services provided by agricultural cooperatives for their members is often not considered in academic studies. Addressing this gap in the literature, our paper explores the wide array of services provided by agricultural cooperatives and how these extend beyond those they were initially intended to provide. We study the extent and characteristics of service portfolios from 511 agricultural cooperatives in the Tigray region of Ethiopia. Results from two-limit Tobit models confirm that government and NGO-initiated cooperatives have a wide service portfolio compared to member-initiated cooperatives. In many of the studied cooperatives, the services they provide and their portfolios are more diverse than expected. Cooperatives seem to go beyond their focal areas of intervention. Also, those cooperatives that are more outward-oriented and where the chair has contact with other cooperatives or businesses, have a wider service portfolio. These results may help to explain the mixed findings on the impact of cooperative membership.

Abstract: In the biogeochemical flows on Earth, the reactive nitrogen (Nr) level has three times surpassed the safe boundary. The severe transgression of this boundary goes against sustainable planetary development. The modern food production process excessively relies on synthetic Nr fertilizers from the Haber– Bosch process. However, the massive loss of valuable nitrogen resources (i.e., 78-89%) from agriculture has been causing severe nitrogen cascade. Besides, the domestic wastewater in some local areas is discharged without proper treatment, making it a nonnegligible source of Nr pollution for local water bodies. Anthropogenic activities keep pumping out Nr pollution via point-source and non-point-source (NPS) emissions. Compared to the NPS emissions, point sources give visible and identified waste streams. It is vital to intervene the nitrogen cascade from point sources and facilitate humanity back to the safe Nr boundary. The collected and collectible Nr streams from food production, waste management, and recycling secondary raw materials can be used as waste-based fertilizers for agricultural cultivation. Besides the well-investigated recovery of inorganic Nr, organic Nr accounts for a massive Nr proportion on the Earth. Proper handling and treatment make these useful organic fertilizers for soil-based cultivation. However, these organic Nr fertilizers cannot directly apply to fertigation or hydroponic cultivation systems, and further biological conversion via nitrogen mineralization and nitrification to nitrate is essential. Besides the direct Nr cycling, the indirect Nr cycling ‘over the atmosphere’ should also be considered. In this way, the nitrogen cycle can be completed via converting the waste Nr back to nitrogen gas (i.e., Nr removal) and then synthesizing into Nr again. The municipal wastewater treatment plants receive a vast amount of low-strength Nr wastewater (mainly as ammonium) daily. Compared to the conventional nitrification/denitrification process, partial nitritation/anammox (PN/A) is considered a resource- and cost-effective technology for wastewater with a low COD/N ratio. Moreover, the novel autotrophic denitratation/anammox process could be a good Nr removal process for wastewater containing both ammonium and nitrate. This Ph.D. thesis aimed to develop Nr recovery, conversion, and removal bioreactor strategies for different types of waste streams and biomass. Nr recovery was investigated on high-strength Nr waste streams for fertigation or hydroponic applications in Chapters 2 and 3. On the other hand, Nr removal was studied on the medium- to low-strength Nr waste streams in Chapters 4 and 5. In Chapter 2, a novel mineralization and nitrification system was proposed, producing nutrient solutions from solid organic fertilizers for hydroponic systems. Batch tests showed that aerobic incubation at 35°C could realize the NO₃⁻-N production efficiency above 90% from a novel microbial fertilizer. Subsequently, in the stirred tank bioreactor test, NO₃⁻-N production efficiency stabilized in a range of 44-51% under the influent loading rate of 400 mg TN L⁻¹ d⁻¹ at a 5-day HRT. Using Ca(OH)₂ and Mg(OH)₂ as pH control reagents generated the nutrient solutions with different P, Ca, and Mg nutrient levels. After modeling the nutrient balancing process, the proportion of organic-sourced NO₃⁻-N in the Hoagland nutrient solution (HNS) of Ca(OH)₂ scenario was 92.7%, while only 37.4% in the Mg(OH)₂ scenario. Compared to commercial scenarios, the total costs of the organic-sourced HNS can be cost-competitive for hydroponic cultivation. In Chapter 3, the Nr recovery as nitrate (NO₃⁻-N) from diluted human urine (around 670 mg N L⁻¹) was explored in a trickling filter (TF) for the first time. A novel concept of in-situ integrating the TF system into hydroponic systems was proposed as meaningful progress towards sustainable agriculture. The difference between synthetic and real urine in nitrification efficiency was found to be negligible. The full nitrification of alkalinized real urine was realized in the pH-controlled TF by calcium hydroxide (Ca(OH)₂) at around pH 6. The TF could handle different urine collection batches and maintain relatively stable nitrification performance, with NO₃⁻-N production efficiency and rate of 88±3% and 136±4 mg N L⁻¹ d⁻¹, respectively. The optimal HLR to realize this nitrification performance was 2 m³ m⁻² h⁻¹, with energy consumption of 1.8 kWh electricity kg⁻¹ NO₃⁻-N production. Ca(OH)₂, as a cheap base, its triple advantages on urine alkalinization, full nitrification, and macronutrient supplementation were successfully demonstrated in our proposed concept. In Chapter 4, towards more sustainable wastewater treatment, the feasibility of one-stage partial nitritation/anammox (PN/A) was investigated in three parallel packed-bed trickling filters (TFs), with three types of carrier materials of different specific surface areas. Synthetic wastewater containing 100-250 mg NH₄⁺-N L⁻¹ was tested to mimic medium-strength household waste streams after carbon removal. Interestingly, the cheap carrier based on expanded clay achieved similar rates as commercially used plastic carrier materials. The top passive ventilation combined with an optimum hydraulic loading rate of 1.8 m³ m⁻² h⁻¹ could reach approximately 60% total nitrogen (TN) removal at a rate of 300 mg N L⁻¹ d⁻¹. A relatively low NO₃⁻-N production (13%) via PN/A was achieved in TFs. Most of the TN removal took place in the top compartment, where anammox activity was the highest. Energy consumption estimation (0.78 kWh electricity g⁻¹ N removed) suggested that the proposed process could be a suitable low-cost alternative for nitrogen removal. In Chapter 5, coupling sulfur-driven denitratation (SDN) with anammox was proposed to treat the wastewater containing both NO₃⁻-N and NH₄⁺-N, like the secondary effluents of mainstream PN/A processes. To explore the feasibility of sufficient and stable NO₂⁻-N accumulation via SDN in the long term, the effects of pH setpoints, residual NO₃⁻-N level, and biomass-specific NO₃⁻-N loading rate (BSNLR) were investigated. Alternating the pH setpoints between 7.0 and 8.5 could temporarily stimulate the NO₂⁻-N accumulation. Both the residual NO₃⁻-N and BSNLR showed highly positive correlations with the NO₂⁻-N accumulation efficiency. Under the control of pH 8.5, 1.0±0.8 mg NO₃⁻-N L⁻¹ and 150±42 mg NO₃⁻-N g⁻¹ VSS d⁻¹, SDN could produce 6.4±1.0 mg NO₂⁻-N L⁻¹ in the short term. Thiobacillus members may play a crucial role in managing the NO₂⁻-N accumulation, but the reduction of abundance and possible adaptation significantly impaired the efficacy of control strategies in the long run. Overall, novel technologies have been proposed to sustainably convert Nr in waste streams and biomass. The decision for Nr recovery versus removal and synthesis should be based on specific cases with the best environmental, economic, and human-health sustainability. In the future, the Nr management concepts should be further improved to make the nitrogen cycle more sustainable with higher resource use efficiency and less Nr emissions to the environment. Although the thesis is mainly focused on limited types of Nr waste streams, it pointed out the direction of sustainable Nr management and could facilitate the Nr back to the safe boundary in the long run.

Abstract: Exposure to volatile organic compounds (VOCs) remains a major public health concern. Indoor VOC concentrations typically far exceed outdoor levels due to a variety of emission sources and the stringent insulation measures that are imposed today. Many attempts have been made to use photocatalysis for indoor air purification. In an ideal situation, photocatalysis is capable of complete mineralization of VOCs to H2O and CO2, without any byproduct formation. Moreover, the process can take place at standard atmospheric conditions, i.e. ambient temperature and atmospheric pressure. However, successful exploitation is still impeded due to low conversion efficiency, significant pressure loss (and hence a high energy consumption) and byproduct formation. In the first part of this thesis an attempt was made to tackles these problems by designing a novel type of photocatalytic (PCO) reactor. The PCO device consists of a cylindrical vessel filled with TiO2-coated glass tubes and equipped with UV fluorescence lamps. It was investigated in terms of fluid dynamics, coating properties, UV-light distribution and photocatalytic activity. Experimental data was later used to develop and calibrate a Multiphysics model. The model proved to be a useful tool for designing and upscaling the PCO reactor. Consequently, an optimized prototype reactor was constructed and tested according the CEN-EN-16846-1 standard for VOC removal. Although the prototype showed promising results for lab-scale conditions, it struggled with byproduct formation when purifying ppb-level VOCs. In the second part of this thesis, activated carbon adsorption was investigated in order to combine it with photocatalysis. Activated carbon fiber was opted for its fast kinetics, high adsorption capacity and thermo-electrical regeneration. The filter was studied in detail regarding the adsorption of polar and apolar VOCs at indoor air concentration levels and regeneration capabilities. Experimental data was used to develop a Multiphysics model for activated carbon adsorption as well. Consequently, a novel type of ACF filter was developed using the Multiphysics model, which was equipped with electrodes in the tips of the pleats for effective thermal regeneration. In the last part, the combination of both ACF and PCO was studied using a realistic case study. Based on the Multiphysics model, the feasibility of a so-called hybrid air purification device could be investigated. The Multiphysics model shows promising results for this hybrid PCO-ACF system and hence, a demo setup was constructed for future research.

Abstract: Achieving global sustainability goals will require cleaner and cheaper technologies. Public policy is central to achieving these goals and, in turn, ensuring a quicker pace of change. A major obstacle lies in the fact that technologies cannot be considered isolated entities: they are embedded in a powerful social context of cultural, organisational and institutional systems. This intertwining of different elements is referred to as a socio-technical system. This thesis discusses how socio-technical systems have, over time, allowed locked-in configurations to emerge, referring to a combination of systematic forces that perpetuate unsustainable infrastructures embedded in society. Such lock-ins can inhibit innovation and competitiveness of low-carbon and sustainable technologies, and this thesis looks to concrete solutions for unlocking them. Vital to this objective lies better understanding preferences, intentions, and behaviour of actors involved at each stage of technological development to improve public policy design. A discrete choice experiment – a quantitative non-market valuation method – was, therefore, a core method used to model preferences of key target groups. Target groups considered in the four components of the thesis include i) industry players, ii) policymakers, iii) farmers, and iv) the general public in Belgium, France, Germany, Italy and Spain. The thesis seeks to establish how both economic and regulatory instruments can be leveraged to overcome lock-in. One conclusion sees that implementing an efficient environmental tax regime – an economic instrument – requires balancing political feasibility and public acceptance considerations in line with tax and environmental policy. Results indicate that public acceptance for environmental taxation increases with earmarking. Another conclusion highlights the importance of taking behavioural and habitual considerations into account – both when considering policymakers’ investment decisions, and farmers’ decisions to adopting agro-ecological practices when responding to regulatory instruments. Overall, policy design should emphasise a more continuous and systemic approach to innovation and technology policy on the road to accelerating socio-technical transitions to sustainability.

Abstract: Novel quantum phases of matter and developing practical control over their characteristics is one of the primary aims of current condensed matter physics. It offers the potential for a new generation of energy, electronic and photonic technologies. Among all the newly found phases of matter, topological insulators are novel phases of quantum matter with fascinating bulk band topology and surface states protected by specific symmetries. For example, at the boundary of a strong topological insulator and a trivial insulator, metallic surface states appear that are protected by time-reversal symmetry. As a result, the bulk continues to be insulating, while the surface can support exotic high-mobility spin-polarized electronic states. Since there is no such thing as a clean system, impurities and other disorders are always present in materials. Even while impurities appear to be unfavorable to a system at first look, doping the host system with impurities allows us to engineer different electronic properties of systems, such as the Fermi level or electron density. Because of the symmetry protected metallic states in topological insulators, charge transport responds distinctively to magnetic and non-magnetic impurities. This doctoral dissertation explores how the longitudinal charge transport in magnetic topological thin films and the anomalous Hall effect on the surface of 3D magnetic topological insulators is influenced by point-like and randomly distributed dilute magnetic impurities. We are interested in how charge transport in these systems responds to the orientation of the magnetization orientation and how this response evolves based on the system's main characteristics, such as the magnitude of the Fermi level or gate voltage. Because topological insulators have a strong spin-orbit coupling, the interaction between conducting electrons and local magnetic impurities is very anisotropic. We will show that this anisotropy even enhances when magnetic topological thin films are exposed to a substrate or gate voltage. Therefore, to properly capture this anisotropy in charge transport calculations, we rely on a generalized Boltzmann formalism together with a modified relaxation time scheme. We show that magnetic impurities affect the charge transport in topological insulators by inducing a transition selection rule that governs scatterings of electrons between various electronic states. We see that this selection rule is highly sensitive to the spin direction of the magnetic impurities as well as the position of the Fermi level. According to this selection rule and depending on the position of the Fermi level, two different transport regimes are realized in magnetic topological thin films. In one of these regimes, our findings show that a dissipation less charge current can be generated. In other words, even if there are many magnetic impurities in the system, electrons do not notice them and, remarkably, conduct charge without dissipation. Outside this regime, the charge transport is always dissipative and its sensitivity to the spatial orientation of the magnetic impurities can be effectively modulated by a substrate or gate voltage. In this doctoral thesis, we also explore the anomalous Hall effect (AHE) on the surface of 3D magnetic topological insulators. The AHE is generated by three mechanisms: the intrinsic effect (owing to a nonzero Berry curvature), the side jump effect, and the skew scattering effect. They compete to dominate the AHE in distinct regimes. Analytically, we calculate the contributions of all three mechanisms to the scattering of massive Dirac fermions by magnetic impurities. Our results reveal three transport regimes based on the relative importance of the engaged mechanisms. The identification of these three distinctive transport regimes can assist experimentalists in achieving a regime in which each contribution is dominant over the others, allowing them to measure them separately. Typically, this is not feasible empirically since the total value of the experimentally observed AHE conceals the specific information of each of the three contributions. Based on our analytical calculations, we prove that the AHE can change sign by varying the orientation of the surface magnetization, the concentration of impurities, and the location of the Fermi level, which is consistent with previous experimental findings. In addition, we show that by suitably adjusting the given parameters, any contribution to the AHE, or even the entire AHE, can be turned off. For example, in a system with in-plane magnetization, one can turn off the AHE by pushing the system into the completely metallic regime. Furthermore, we demonstrate that any contribution to the AHE, or even the whole AHE, can be turned off by appropriately changing the provided parameters. For example, in a system with in-plane magnetization, the AHE can be turned off by pushing the system into the fully metallic regime.

Abstract: By combining statistical parameter estimation and model-order selection using a Bayesian framework, the maximum a posteriori (MAP) probability rule is proposed in this chapter as an objective and quantitative method to detect atom columns from high-resolution scanning transmission electron microscopy (HRSTEM) images. The validity and usefulness of this approach is demonstrated to both simulated and experimental annular dark-field (ADF) STEM images, but also to simultaneously acquired annular bright-field (ABF) and ADF STEM image data.

Abstract: In this thesis, a first-principles research to tune the physical properties of group III-V materials in the thinnest limit is carried out. Among the different methods to tune the mechanical, electronic and magnetic properties of these graphene related materials, we use: two-dimensional (2D) multilayers, straintronics, hydrogen functionalization, and transition metal adsorption. The first part of this research is devoted to a complete characterization of the structural, electronic, mechanical and vibrational properties of 2D group III-As monolayers, obtained from density functional theory. Our findings are used to understand the contribution of the