|
Van Hal M (2021) Photo(electro)catalytic air purification and soot degradation with simultaneous energy recovery. XXXII, 203 p
Abstract: Today’s society is increasingly challenged by a range of urgent environmental problems. Air pollution is one of these pressing topics. This thesis will mainly focus on the degradation of volatile organic compounds (VOCs) and particulate matter (PM) – more specifically soot. A second globally urging topic is the quest for sustainable energy production. To simultaneously target both environmental problems, a photoelectrochemical (PEC) cell will be studied in this thesis, combining air purification and sustainable energy production in a single device. Photocatalysis is used at the anode of the PEC cell to drive the air purification process, while the energy contained in the degraded compounds is (partially) recovered at the cathode, either as H2 gas or electricity. The first two experimental chapters focus on the proof of concept of such an unbiased all-gas phase PEC cell targeting VOC degradation, using both TiO2- and WO3-based photocatalysts. In the two following experimental chapters the photocatalytic soot oxidation capacity of these TiO2- and WO3-based photocatalysts was studied. In the final experimental chapter the previously obtained results were combined, striving towards an efficient, sunlight-driven and soot-degrading waste gas-to-energy PEC cell.
Keywords: Doctoral thesis; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
“Towards developing a screening strategy for ecstasy : revealing the electrochemical profile”. Thiruvottriyur Shanmugam S, Van Echelpoel R, Boeye G, Eliaerts J, Samanipour M, Ching HYV, Florea A, Van Doorslaer S, Van Durme F, Samyn N, Parrilla M, De Wael K, Chemelectrochem 8, 4826 (2021). http://doi.org/10.1002/CELC.202101198
Abstract: This article describes the development of an electrochemical screening strategy for 3,4-methylenedioxymethamphetamine (MDMA), the regular psychoactive compound in ecstasy (XTC) pills. We have investigated the specific electrochemical profile of MDMA and its electro-oxidation mechanisms at disposable graphite screen-printed electrodes. We have proved that the formation of a radical cation and subsequent reactions are indeed responsible for the electrode surface passivation, as evidenced by using electron paramagnetic resonance spectroscopy and electrochemistry. Thereafter, pure cutting agents and MDMA as well as simulated binary mixtures of compounds with MDMA were subjected to square wave voltammetry at pH 7 to understand the characteristic electrochemical profile. An additional measurement at pH 12 was able to resolve false positives and negatives occurring at pH 7. Finally, validation of the screening strategy was done by measuring a set of ecstasy street samples. Overall, our proposed electrochemical screening strategy has been demonstrated for the rapid, sensitive, and selective detection of MDMA, resolving most of the false positives and negatives given by the traditional Marquis color tests, thus exhibiting remarkable promises for the on-site screening of MDMA.
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Organic synthesis (ORSY); Applied Electrochemistry & Catalysis (ELCAT); Antwerp Electrochemical and Analytical Sciences Lab (A-Sense Lab)
Impact Factor: 4.136
DOI: 10.1002/CELC.202101198
|
|
|
“Nitrogen fixation in an electrode-free microwave plasma”. Kelly S, Bogaerts A, Joule 5, 3006 (2021). http://doi.org/10.1016/j.joule.2021.09.009
Abstract: Plasma-based gas conversion has great potential for enabling carbon-free fertilizer production powered by renewable electricity. Sustaining an energy-efficient plasma process without eroding the containment vessel is currently a significant challenge, limiting scaling to higher powers and throughputs. Isolation of the plasma from contact with any solid surfaces is an advantage, which both limits energy loss to the walls and prevents material erosion that could lead to disastrous soil contamination. This paper presents highly energy-efficient nitrogen fixation from air into NOx by microwave plasma, with the plasma filament isolated at the center of a quartz tube using a vortex gas flow. NOx production is found to scale very efficiently when increasing both gas flow rate and absorbed power. The lowest energy cost recorded of ~2 MJ/mol, for a total NOx production of ~3.8%, is the lowest reported up to now for atmospheric pressure plasmas.
Keywords: A1 Journal Article; Plasma, laser ablation and surface modeling Antwerp (PLASMANT) ;
DOI: 10.1016/j.joule.2021.09.009
|
|
|
“Third-Order Nonlinear Optical Properties and Saturation of Two-Photon Absorption in Lead-Free Double Perovskite Nanocrystals under Femtosecond Excitation”. Mushtaq A, Pradhan B, Kushavah D, Zhang Y, Wolf M, Schrenker N, Fron E, Bals S, Hofkens J, Debroye E, Pal SK, Acs Photonics 8, 3365 (2021). http://doi.org/10.1021/acsphotonics.1c01351
Abstract: Lead halide perovskites have been widely explored
in the field of photovoltaics, light-emitting diodes, and lasers due to
their outstanding linear and nonlinear optical (NLO) properties.
But, the presence of lead toxicity and low chemical stability remain
serious concerns. Lead-free double perovskite with excellent
optical properties and chemical stability could be an alternative.
However, proper examination of the NLO properties of such a
material is crucial to identify their utility for future nonlinear device
applications. Herein, we have made use of femtosecond (fs) Z-scan
technique to explore the NLO properties of Cs2AgIn0.9Bi0.1Cl6
nanocrystals (NCs). Our measurements suggest that under
nonresonant fs excitation, perovskite NCs exhibit strong twophoton
absorption (TPA). The observed saturation of TPA at high
light intensities has been explained by a customized model. Furthermore, we have demonstrated a change in the nonlinear refractive
index of the NCs under varying input intensities. The strong TPA absorption of lead-free double perovskite NCs could be used for
Kerr nonlinearity-based nonlinear applications such as optical shutters for picosecond lasers.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 6.756
Times cited: 25
DOI: 10.1021/acsphotonics.1c01351
|
|
|
“Plasma–liquid interactions”. Bruggeman PJ, Bogaerts A, Pouvesle JM, Robert E, Szili EJ, Journal Of Applied Physics 130, 200401 (2021). http://doi.org/10.1063/5.0078076
Keywords: A1 Journal Article; Plasma, laser ablation and surface modeling Antwerp (PLASMANT) ;
Impact Factor: 2.068
DOI: 10.1063/5.0078076
|
|
|
Maciel de Menezes R (2021) Skyrmionics and magnonics in chiral ferromagnets : from micromagnetic to atomistic control. 222 p
Abstract: The precise control of skyrmionics and magnonics in magnetic materials is key to the development of novel spin-based technology and information transport applications. Essentially, the inherent stability of magnetic skyrmions (provided by their topological charge) together with their extremely small size (down to a few nanometers) and the ultralow threshold current necessary to move them in nanostructures are the main advantages of skyrmionics. Not least, magnonics offers lower power consumption compared to electronics and the excitation of high frequency (sub-100~nm wavelength) magnons makes it possible for the creation of nanometric devices for ultrafast information transport. Even though extensive research has been carried out in recent years, the precise manipulation of skyrmions and spin waves (magnons) in nanostructures is not fully mastered and needs to be addressed before making functional skyrmionic and magnonic devices. In this thesis, we reveal multiple alternatives for the manipulation of skyrmions and spin-waves in different materials, such as bulk chiral magnets, heterochiral structures, magnet-supperconductor hybrids and two-dimentional magnetic materials. We make use of a multiscale model to numerically simulate the magnetic states at each considered material, from micromagnetic to atomistic control. We first explore the different nucleation mechanisms, activation energy, and the time evolution of the skyrmion formation in chiral magnetic films, crucial for the realization of skyrmion-based devices. We show that the skyrmion lattice is formed from the conical phase progressively, most probably by the formation of chiral bobbres, followed by the cylindrical growth of individual skyrmions from the film surface. That reflects a rod-like (one-dimensional) nucleation of the skyrmion phase, with an activation barrier of several electronvolts per skyrmion for the case of MnSi (Manganese monosilicide). In addition, we reveal the interesting blinking (creation-annihilation) behavior of skyrmions close to the phase boundary between the conical and skyrmion phases, where we recall that such switching between topologically distinct states has been proposed as a bit operation for information storage. Next, we discuss the motion of ferromagnetic and antiferromagnetic skyrmions in heterochiral magnets. We report the characteristic deflection of ferromagnetic skyrmions when moving across a heterochiral interface, where the extent of such deflection is tuned by the applied spin-polarized current and the magnitude of Dzyaloshinskii-Moriya interaction. Following, we show that the antiferromagnetic skyrmion achieves much higher velocities than its ferromagnetic counterpart, yet experiences far stronger confinement in nanoengineered heterochiral tracks, which reinforces antiferromagnetic skyrmions as a favorable choice for skyrmion-based devices. After that, we study the interesting coupling of magnetic skyrmions and superconducting vortices in magnet-superconductor heterostructures. We perform numerical simulations, based on experimental observations, to demonstrate that the stray field of magnetic skyrmions can nucleate antivortices in an adjacent superconducting film, giving rise to a hybrid topological object, the skyrmion-vortex pair, which harbor promising features for skyrmionics and quantum computing applications. We then explore the manipulation of a single skyrmion-vortex pair when currents are applied into both superconducting and magnetic parts of the heterostructure, which is of importance for the facilitated skyrmion guidance in racetrack applications. Afterwards, we make use of the high tunability of magnetic parameters in two-dimensional magnetic materials to reveal the rich phase diagram of exotic magnetic configurations in magnetic monolayers with suppressed nearest-neighbour exchange, where we show that several unique cycloidal, checkerboard, row-wise and spin-ice states are stabilized by the competition between the second-nearest-neighbor exchange, Dzyaloshinskii-Moriya, and dipolar interactions. Additionally, we show the coexistence of ferromagnetic and antiferromagnetic spin-cycloids, as well as novel types of skyrmions and chiral domain walls. Finally, in the last part of the thesis, we present the spin wave properties in the two-dimensional magnetic materials CrBr$3$ and CrI$3$. Using spin-dynamics simulations parametrized from first principles, we reveal that the spin wave dispersion in such materials can be tuned in a broad range of frequencies by strain-engineering, and that a designed pattern of strain, as well as structural defects (halide vacancies) can be turned useful in the design of spin-wave guides. Lastly, we discuss the realization of magnonic crystals by moiré-periodic modulation of magnetic parameters in van der Waals heterostructures, where we show that the several nanometer small periodicities in such samples are ideal for the interference of terahertz spin waves. Recalling the wide range of possibilities for manipulating spin waves in such two-dimensional materials, we therefore suggest these systems as a front-runner for prospective terahertz magnonic applications.
Keywords: Doctoral thesis; Condensed Matter Theory (CMT)
|
|
|
Zhu W (2021) Microbial resource management for mainstream partial nitritation/anammox : strategies to enhance the nitrogen conversion efficiency. 207 p
Abstract: This thesis provides three potential ways to enhance the nitrogen removal efficiency of mainstream partial nitritation/anammox (PN/A), a key technology to enable energy-positive sewage treatment. In Chapter 1, the typical technologies to promote nitrogen removal efficiency are summarized. In Chapters 2 and 3, the concept ‘winter bioaugmentation with stored summer surplus sludge’ is proposed. Applying that, a cost-effective sludge preservation strategy is required. Preserving PN/A biomass without cooling and redox adjustment proved to be the cost-effective strategy. The reactivation of these stored sludges was also tested in low-temperature systems (15 and 10℃). Respectively 56% and 41% of granules activity compared to pre-storage activity (after Arrhenius-based temperature correction) could be recovered within a month (41% and 32% for flocs activity). In the end, the stored AnAOB bioaugmentation was successfully validated in the lab (20℃). In Chapter 4, a return-sludge nursery concept, applying the sidestream nitritation and blending the resulting effluent with mainstream effluent to achieve an intermediate temperature and nitrogen concentrations, is proposed. That led to a 33 – 36% increase in nitrogen removal efficiency. Arrhenius’ expectations (10 ℃ higher temperature, θ = 1.09) could only explain 49-51% of the activity increase in the nursery reactor, pointing to the role of other factors, e.g., the ~400% elevated electrical conductivity (15-16%), the 56-335% higher effluent nitrogen concentrations (12-14%), and the synergy and unknown factors (20-23%). Thus, the return-sludge biostimulation approach could also enhance nitrogen efficiency in the mainstream. In Chapter 5, the N2O emissions, linked to three typical nitrite-oxidizing bacteria (NOB) suppression strategies (low dissolved oxygen (DO) level, free ammonia (FA), and free nitrous acids (FNA) treatments) were tested in a biofilm system. A low emerged DO level (~0.60 mg O2 L-1) was effective to suppress NOB activity and decrease N2O emissions, but NOB adaptation gradually appeared after 200 days. Further NOB inhibition was successfully achieved by periodical (3 hours per week) FA (~30 mg NH3-N L-1) or FNA (~3 mg HNO2-N L-1) treatments. The FA treatment promoted N2O production, while the FNA treatment had no effect. Thus, PN/A systems should be operated at relatively low DO levels with periodical FNA treatment. In Chapter 6, the major findings proposed and the main conclusions drawn in this thesis are outlined. Beyond that, the possible design of a mainstream PN/A configuration that combined all described three technologies is demonstrated. Overall, the novel insights from this thesis potential to improve nitrogen removal efficiency in the mainstream.
Keywords: Doctoral thesis; Sustainable Energy, Air and Water Technology (DuEL)
|
|
|
“Optical encoding of luminescent carbon nanodots in confined spaces”. Bartholomeeusen E, De Cremer G, Kennes K, Hammond C, Hermans I, Lu J-B, Schryvers D, Jacobs PA, Roeffaers MBJ, Hofkens J, Sels BF, Coutino-Gonzalez E, Chemical Communications 57, 11952 (2021). http://doi.org/10.1039/D1CC04777A
Abstract: Stable emissive carbon nanodots were generated in zeolite crystals using near infrared photon irradiation gradually converting the occluded organic template, originally used to synthesize the zeolite crystals, into discrete luminescent species consisting of nano-sized carbogenic fluorophores, as ascertained using Raman microscopy, and steady-state and time-resolved spectroscopic techniques. Photoactivation in a confocal laser fluorescence microscope allows 3D resolved writing of luminescent carbon nanodot patterns inside zeolites providing a cost-effective and non-toxic alternative to previously reported metal-based nanoclusters confined in zeolites, and opens up opportunities in bio-labelling and sensing applications.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 6.319
DOI: 10.1039/D1CC04777A
|
|
|
“Towards ductilization of high strength 7XXX aluminium alloys via microstructural modifications obtained by friction stir processing and heat treatments”. Lezaack MB, Hannard F, Zhao L, Orekhov A, Adrien J, Miettinen A, Idrissi H, Simar A, Materialia 20, 101248 (2021). http://doi.org/10.1016/J.MTLA.2021.101248
Abstract: High strength 7XXX aluminium series reach exceptional strength, higher than all other industrial aluminium alloys. However, they suffer from a lack of ductility compared to softer series. This work presents a procedure to improve the ductility of 7475 Al alloy in high strength condition, reaching a true fracture strain of 70% at full 500 MPa T6 yield strength. Using friction stir processing (FSP) and post-FSP heat treatments, 100% of industrial rolled material T6 yield stress is maintained but a 180% increase in fracture strain is measured for the processed material. This ductility improvement is studied by in-situ synchrotron X-ray tomography and is explained by the reduction of intermetallic particles size and the homogenization of their spatial distribution. Furthermore, the microstructure after FSP shows equiaxed refined grains which favour crack deviation as opposed to large cracks parallel to the elongated coarse grains in rolled plate. These results are paving the way to better formability and crashworthiness of 7XXX alloys.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
DOI: 10.1016/J.MTLA.2021.101248
|
|
|
“Developing feature-rich electronic and magnetic properties in the beta-As monolayer for spintronic and optoelectronic applications by C and Si doping : a first-principles study”. Hoat DM, Duy Khanh Nguyen, Bafekry A, Vo Van On, Ul Haq B, Hoang D-Q, Cocoletzi GH, Rivas-Silva JF, Surfaces and interfaces 27, 101534 (2021). http://doi.org/10.1016/J.SURFIN.2021.101534
Abstract: In this work, the carbon (C) and silicon (Si) doping and codoping effects on beta-arsenene (As) monolayer structural, electronic, and magnetic properties have been comprehensively investigated using first-principles calculations. The studied two-dimensional (2D) materials exhibit good stability. Pristine beta-As single layer is an indirect gap semiconductor with a band gap of 1.867(2.441) eV as determined by PBE(HSE06) functional. Due to the difference in atomic size and electronic interactions, C and Si substitution induces a significant local structural distortion. Depending upon dopant concentration and doping sites, feature-rich electronic properties including non-magnetic semiconductor, magnetic semiconductor and half-metallicity may be obtained, which result from p-p interactions. High spin-polarization at the Fermi level vicinity and significant magnetism suggest As:1C, As:2C, As:1Si, As:2Si, and As:CSi systems as prospective spintronic 2D materials. While, the C-C, Si-Si, and C-Si dimer doping decreases electronic band gap, making the layer more suitable for applications in optoelectronic devices. Results presented herein may suggest an efficient approach to create novel multi-functional 2D materials from beta-As monolayer.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
DOI: 10.1016/J.SURFIN.2021.101534
|
|
|
“Breakdown of universal scaling for nanometer-sized bubbles in graphene”. Villarreal R, Lin P-C, Faraji F, Hassani N, Bana H, Zarkua Z, Nair MN, Tsai H-C, Auge M, Junge F, Hofsaess HC, De Gendt S, De Feyter S, Brems S, Ahlgren EH, Neyts EC, Covaci L, Peeters FM, Neek-Amal M, Pereira LMC, Nano Letters 21, 8103 (2021). http://doi.org/10.1021/ACS.NANOLETT.1C02470
Abstract: We report the formation of nanobubbles on graphene with a radius of the order of 1 nm, using ultralow energy implantation of noble gas ions (He, Ne, Ar) into graphene grown on a Pt(111) surface. We show that the universal scaling of the aspect ratio, which has previously been established for larger bubbles, breaks down when the bubble radius approaches 1 nm, resulting in much larger aspect ratios. Moreover, we observe that the bubble stability and aspect ratio depend on the substrate onto which the graphene is grown (bubbles are stable for Pt but not for Cu) and trapped element. We interpret these dependencies in terms of the atomic compressibility of the noble gas as well as of the adhesion energies between graphene, the substrate, and trapped atoms.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Condensed Matter Theory (CMT); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 12.712
Times cited: 24
DOI: 10.1021/ACS.NANOLETT.1C02470
|
|
|
“Kinetic regulation of the synthesis of pentatwinned gold nanorods below room temperature”. Sanchez-Iglesias A, Jenkinson K, Bals S, Liz-Marzan LM, Journal Of Physical Chemistry C 125, 23937 (2021). http://doi.org/10.1021/ACS.JPCC.1C07284
Abstract: The synthesis of gold nanorods requires the presence of symmetry-breaking and shape-directing additives, among which bromide ions and quaternary ammonium surfactants have been reported as essential. As a result, hexadecyltrimethylammonium bromide (CTAB) has been selected as the most efficient surfactant to direct anisotropic growth. One of the difficulties arising from this selection is the low solubility of CTAB in water at room temperature, and therefore the seeded growth of gold nanorods is usually performed at 25 degrees C or above, which has restricted so far the analysis of kinetic effects derived from lower temperatures. We report a systematic study of the synthesis of gold nanorods from pentatwinned seeds using hexadecyltrimethylammonium chloride (CTAC) as the principal surfactant and a low concentration of bromide as shape-directing agent. Under these conditions, the synthesis can be performed at temperatures as low as 8 degrees C, and the corresponding kinetic effects can be studied, resulting in temperature-controlled aspect ratio tunability.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 4.536
Times cited: 6
DOI: 10.1021/ACS.JPCC.1C07284
|
|
|
“2D quantum materials : magnetism and superconductivity”. Milošević, MV, Mandrus D, Journal Of Applied Physics 130, 180401 (2021). http://doi.org/10.1063/5.0075774
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.068
DOI: 10.1063/5.0075774
|
|
|
“Stability of adsorption of Mg and Na on sulfur-functionalized MXenes”. Chaney G, Cakir D, Peeters FM, Ataca C, Physical Chemistry Chemical Physics 23, 25424 (2021). http://doi.org/10.1039/D1CP03433B
Abstract: Two-dimensional materials composed of transition metal carbides and nitrides (MXenes) are poised to revolutionize energy conversion and storage. In this work, we used density functional theory (DFT) to investigate the adsorption of Mg and Na adatoms on five M2CS2 monolayers (where M = Mo, Nb, Ti, V, and Zr) for battery applications. We assessed the stability of the adatom (i.e. Na and Mg)-monolayer systems by calculating adsorption and formation energies, as well as voltages as a function of surface coverage. For instance, we found that Mo2CS2 cannot support a full layer of Na nor even a single Mg atom. Na and Mg exhibit the strongest binding on Zr2CS2, followed by Ti2CS2, Nb2CS2 and V2CS2. Using the nudged elastic band method (NEB), we computed promising diffusion barriers for both dilute and nearly full ion surface coverage cases. In the dilute ion adsorption case, a single Mg and Na atom on Ti2CS2 experience similar to 0.47 eV and similar to 0.10 eV diffusion barriers between the lowest energy sites, respectively. For a nearly full surface coverage, a Na ion moving on Ti2CS2 experiences a similar to 0.33 eV energy barrier, implying a concentration-dependent diffusion barrier. Our molecular dynamics results indicate that the three (one) layers (layer) of the Mg (Na) ion on both surfaces of Ti2CS2 remain stable at T = 300 K. While, according to voltage calculations, Zr2CS2 can store Na up to three atomic layers, our MD simulations predict that the outermost layers detach from the Zr2CS2 monolayer due to the weak interaction between Na ions and the monolayer. This suggests that MD simulations are essential to confirm the stability of an ion-electrode system – an insight that is mostly absent in previous studies.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 4.123
Times cited: 7
DOI: 10.1039/D1CP03433B
|
|
|
“Tailoring dirac plasmons via anisotropic dielectric environment by design”. Tao ZH, Dong HM, Milošević, MV, Peeters FM, Van Duppen B, Physical Review Applied 16, 054030 (2021). http://doi.org/10.1103/PHYSREVAPPLIED.16.054030
Abstract: Dirac plasmons in a two-dimensional (2D) crystal are strongly affected by the dielectric properties of the environment, due to interaction of their electric field lines with the surrounding medium. Using graphene as a 2D reservoir of free carriers, one can engineer a material configuration that provides an anisotropic environment to the plasmons. In this work, we discuss the physical properties of Dirac plasmons in graphene surrounded by an arbitrary anisotropic dielectric and exemplify how h-BN-based heterostructures can be designed to bear the required anisotropic characteristics. We calculate how dielec-tric anisotropy impacts the spatial propagation of the plasmons and find that an anisotropy-induced plasmon mode emerges, together with a damping pathway, that stem from the out-of-plane off-diagonal elements in the dielectric tensor. Furthermore, we find that one can create hyperbolic plasmons by inher-iting the dielectric hyperbolicity of the designed material environment. Strong control over plasmon propagation patterns can be realized in a similar manner. Finally, we show that in this way one can also control the polarization of the light-matter excitations that constitute the plasmon. Taken together, our results promote the design of the dielectric environment as an effective path to tailor the plasmonic response of graphene on the nanoscopic level.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 4.808
Times cited: 2
DOI: 10.1103/PHYSREVAPPLIED.16.054030
|
|
|
“Electronic transport mechanisms correlated to structural properties of a reduced graphene oxide sponge”. Pinto N, McNaughton B, Minicucci M, Milošević, MV, Perali A, Nanomaterials 11, 2503 (2021). http://doi.org/10.3390/NANO11102503
Abstract: We report morpho-structural properties and charge conduction mechanisms of a foamy “graphene sponge ”, having a density as low as & AP;0.07 kg/m3 and a carbon to oxygen ratio C:O & SIME; 13:1. The spongy texture analysed by scanning electron microscopy is made of irregularly-shaped millimetres-sized small flakes, containing small crystallites with a typical size of & SIME;16.3 nm. A defect density as high as & SIME;2.6 x 1011 cm-2 has been estimated by the Raman intensity of D and G peaks, dominating the spectrum from room temperature down to & SIME;153 K. Despite the high C:O ratio, the graphene sponge exhibits an insulating electrical behavior, with a raise of the resistance value at & SIME;6 K up to 5 orders of magnitude with respect to the room temperature value. A variable range hopping (VRH) conduction, with a strong 2D character, dominates the charge carriers transport, from 300 K down to 20 K. At T < 20 K, graphene sponge resistance tends to saturate, suggesting a temperature-independent quantum tunnelling. The 2D-VRH conduction originates from structural disorder and is consistent with hopping of charge carriers between sp2 defects in the plane, where sp3 clusters related to oxygen functional groups act as potential barriers.</p>
Keywords: A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT)
Impact Factor: 3.553
DOI: 10.3390/NANO11102503
|
|
|
Van Alphen S, Slaets J, Ceulemans S, Aghaei M, Snyders R, Bogaerts A (2021) Effect of N2 on CO2-CH4 conversion in a gliding arc plasmatron: Can this major component in industrial emissions improve the energy efficiency? 101767
Abstract: Plasma-based CO2 and CH4 conversion is gaining increasing interest, and a great portion of research is dedicated to adapting the process to actual industrial conditions. In an industrial context, the process needs to be able to process N2 admixtures, since most industrial gas emissions contain significant amounts of N2, and gas separations are financially costly. In this paper we therefore investigate the effect of N2 on the CO2 and CH4 conversion in a gliding arc plasmatron reactor. The addition of 20 % N2 reduces the energy cost of the conversion process by 21 % compared to a pure CO2/CH4 mixture, from 2.9 down to 2.2 eV/molec (or from 11.5 to 8.7 kJ/L), yielding a CO2 and CH4 (absolute) conversion of 28.6 and 35.9 % and an energy efficiency of 58 %. These results are among the best reported in literature for plasma-based DRM, demonstrating the benefits of N2 present in the mix. Compared to DRM results in different plasma reactor types, a low energy cost was achieved. To understand the underlying mechanisms of N2 addition, we developed a combination of four different computational models, which reveal that the beneficial effect of N2 addition is attributed to (i) a rise in the electron density (increasing the plasma conductivity, and therefore reducing the plasma power needed to sustain the plasma, which reduces the energy cost), as well as (ii) a rise in the gas temperature, which accelerates the CO2 and CH4 conversion reactions.
Keywords: A1 Journal Article;Plasma-based CO2-CH4 conversion; Effect of N2; Plasma chemistry; Computational modelling; Gliding arc plasmatron; Plasma, laser ablation and surface modeling Antwerp (PLASMANT) ;
Impact Factor: 4.292
DOI: 10.1016/j.jcou.2021.101767
|
|
|
“Finding the optimal fatty acid composition for biodiesel improving the emissions of a one-cylinder diesel generator”. Maes RR, Potters G, Fransen E, Cayetano FC, Van Schaeren R, Lenaerts S, Sustainability 13, 12089 (2021). http://doi.org/10.3390/SU132112089
Abstract: Nitrogen oxides (NOx) and particulate matter (PM) currently are the main pollutants emitted by diesel engines. While there is a start in using hybrid and electric cars, ships will still be fueled by mineral oil products. In the quest to achieve zero-pollution and carbon-free shipping, alternative forms of energy carriers must be found to replace the commonly used mineral oil products. One of the possible alternative fuels is biodiesel. This paper explores the optimization of the composition of biodiesel in order to reduce the concentration of particulate matter and NOx in exhaust gases of a one-cylinder diesel generator.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 1.789
DOI: 10.3390/SU132112089
|
|
|
“Quasiparticle twist dynamics in non-symmorphic materials”. Juneja R, Thebaud S, Pandey T, Polanco CA, Moseley DH, Manley ME, Cheng YQ, Winn B, Abernathy DL, Hermann RP, Lindsay L, Materials Today Physics 21, 100548 (2021). http://doi.org/10.1016/J.MTPHYS.2021.100548
Abstract: Quasiparticle physics underlies our understanding of the microscopic dynamical behaviors of materials that govern a vast array of properties, including structural stability, excited states and interactions, dynamical structure factors, and electron and phonon conductivities. Thus, understanding band structures and quasiparticle interactions is foundational to the study of condensed matter. Here we advance a 'twist' dynamical description of quasiparticles (including phonons and Bloch electrons) in nonsymmorphic chiral and achiral materials. Such materials often have structural complexity, strong thermal resistance, and efficient thermoelectric performance for waste heat capture and clean refrigeration technologies. The twist dynamics presented here provides a novel perspective of quasiparticle behaviors in such complex materials, in particular highlighting how non-symmorphic symmetries determine band crossings and anti-crossings, topological behaviors, quasiparticle interactions that govern transport, and observables in scattering experiments. We provide specific context via neutron scattering measurements and first-principles calculations of phonons and electrons in chiral tellurium dioxide. Building twist symmetries into the quasiparticle dynamics of non-symmorphic materials offers intuition into quasi particle behaviors, materials properties, and guides improved experimental designs to probe them. More specifically, insights into the phonon and electron quasiparticle physics presented here will enable materials design strategies to control interactions and transport for enhanced thermoelectric and thermal management applications. (C) 2021 Published by Elsevier Ltd.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
DOI: 10.1016/J.MTPHYS.2021.100548
|
|
|
“Voltammetric sensing using an array of modified SPCE coupled with machine learning strategies for the improved identification of opioids in presence of cutting agents”. Ortiz-Aguayo D, De Wael K, del Valle M, Journal Of Electroanalytical Chemistry 902, 115770 (2021). http://doi.org/10.1016/J.JELECHEM.2021.115770
Abstract: This work reports the use of modified screen-printed carbon electrodes (SPCEs) for the identification of three drugs of abuse and two habitual cutting agents, caffeine and paracetamol, combining voltammetric sensing and chemometrics. In order to achieve this goal, codeine, heroin and morphine were subjected to Square Wave Voltammetry (SWV) at pH 7, in order to elucidate their electrochemical fingerprints. The optimized SPCEs electrode array, which have a differentiated response for the three oxidizable compounds, was derived from Carbon, Prussian blue, Cobalt (II) phthalocyanine, Copper (II) oxide, Polypyrrole and Palladium nanoparticles ink-modified carbon electrodes. Finally, Principal Component Analysis (PCA) coupled with Silhouette parameter assessment was used to select the most suitable combination of sensors for identification of drugs of abuse in presence of cutting agents.
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Antwerp Electrochemical and Analytical Sciences Lab (A-Sense Lab)
Impact Factor: 3.012
DOI: 10.1016/J.JELECHEM.2021.115770
|
|
|
“Towards Exotic Layered Materials: 2D Cuprous Iodide”. Mustonen K, Hofer C, Kotrusz P, Markevich A, Hulman M, Mangler C, Susi T, Pennycook TJ, Hricovini K, Richter CM, Meyer JC, Kotakoski J, Skákalová, V, Advanced materials , 2106922 (2021). http://doi.org/10.1002/adma.202106922
Abstract: Heterostructures composed of two-dimensional (2D) materials are already opening many new possibilities in such fields of technology as electronics and magnonics, but far more could be achieved if the number and diversity of 2D materials is increased. So far, only a few dozen 2D crystals have been extracted from materials that exhibit a layered phase in ambient conditions, omitting entirely the large number of layered materials that may exist in other temperatures and pressures. Here, we demonstrate how these structures can be stabilized in 2D van der Waals stacks under room temperature via growing them directly in graphene encapsulation by using graphene oxide as the template material. Specifically, we produce an ambient stable 2D structure of copper and iodine, a material that normally only occurs in layered form at elevated temperatures between 645 and 675 K. Our results establish a simple route to the production of more exotic phases of materials that would otherwise be difficult or impossible to stabilize for experiments in ambient.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 19.791
DOI: 10.1002/adma.202106922
|
|
|
“ab initio description of bonding for transmission electron microscopy”. Madsen J, Pennycook TJ, Susi T, Ultramicroscopy 231 (2021). http://doi.org/10.1016/J.ULTRAMIC.2021.113253
Abstract: The simulation of transmission electron microscopy (TEM) images or diffraction patterns is often required to interpret their contrast and extract specimen features. This is especially true for high-resolution phase-contrast imaging of materials, but electron scattering simulations based on atomistic models are widely used in materials science and structural biology. Since electron scattering is dominated by the nuclear cores, the scattering potential is typically described by the widely applied independent atom model. This approximation is fast and fairly accurate, especially for scanning TEM (STEM) annular dark-field contrast, but it completely neglects valence bonding and its effect on the transmitting electrons. However, an emerging trend in electron microscopy is to use new instrumentation and methods to extract the maximum amount of information from each electron. This is evident in the increasing popularity of techniques such as 4D-STEM combined with ptychography in materials science, and cryogenic microcrystal electron diffraction in structural biology, where subtle differences in the scattering potential may be both measurable and contain additional insights. Thus, there is increasing interest in electron scattering simulations based on electrostatic potentials obtained from first principles, mainly via density functional theory, which was previously mainly required for holography. In this Review, we discuss the motivation and basis for these developments, survey the pioneering work that has been published thus far, and give our outlook for the future. We argue that a physically better justified ab initio description of the scattering potential is both useful and viable for an increasing number of systems, and we expect such simulations to steadily gain in popularity and importance.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.843
DOI: 10.1016/J.ULTRAMIC.2021.113253
|
|
|
“Creation of Exclusive Artificial Cluster Defects by Selective Metal Removal in the (Zn, Zr) Mixed-Metal UiO-66”. Feng X, Jena HS, Krishnaraj C, Arenas-Esteban D, Leus K, Wang G, Sun J, Rüscher M, Timoshenko J, Roldan Cuenya B, Bals S, Voort PVD, Journal Of The American Chemical Society , jacs.1c05357 (2021). http://doi.org/10.1021/jacs.1c05357
Abstract: The differentiation between missing linker defects
and missing cluster defects in MOFs is difficult, thereby limiting the
ability to correlate materials properties to a specific type of defects.
Herein, we present a novel and easy synthesis strategy for the
creation of solely “missing cluster defects” by preparing mixed-metal
(Zn, Zr)-UiO-66 followed by a gentle acid wash to remove the Zn
nodes. The resulting material has the reo UiO-66 structure, typical
for well-defined missing cluster defects. The missing clusters are
thoroughly characterized, including low-pressure Ar-sorption, iDPCSTEM
at a low dose (1.5 pA), and XANES/EXAFS analysis. We
show that the missing cluster UiO-66 has a negligible number of missing linkers. We show the performance of the missing cluster
UiO-66 in CO2 sorption and heterogeneous catalysis.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 13.858
Times cited: 29
DOI: 10.1021/jacs.1c05357
|
|
|
“Nanoparticle-MediatedIn SituMolecular Reprogramming of Immune Checkpoint Interactions for Cancer Immunotherapy”. Walters AA, Santacana-Font G, Li J, Routabi N, Qin Y, Claes N, Bals S, Tzu-Wen Wang J, Al-Jamal KT, Acs Nano 15, 17549 (2021). http://doi.org/10.1021/acsnano.1c04456
Abstract: Immune checkpoint blockade involves targeting immune
regulatory molecules with antibodies. Preclinically, complex multiantibody
regimes of both inhibitory and stimulatory targets are a promising
candidate for the next generation of immunotherapy. However, in this
setting, the antibody platform may be limited due to excessive toxicity
caused by off target effects as a result of systemic administration. RNA
can be used as an alternate to antibodies as it can both downregulate
immunosuppressive checkpoints (siRNA) or induce expression of
immunostimulatory checkpoints (mRNA). In this study, we demonstrate
that the combination of both siRNA and mRNA in a single
formulation can simultaneously knockdown and induce expression of
immune checkpoint targets, thereby reprogramming the tumor
microenvironment from immunosuppressive to immunostimulatory
phenotype. To achieve this, RNA constructs were synthesized and
formulated into stable nucleic acid lipid nanoparticles (SNALPs); the SNALPs produced were 140−150 nm in size with >80%
loading efficiency. SNALPs could transfect macrophages and B16F10 cells in vitro resulting in 75% knockdown of inhibitory
checkpoint (PDL1) expression and simultaneously express high levels of stimulatory checkpoint (OX40L) with minimal
toxicity. Intratumoral treatment with the proposed formulation resulted in statistically reduced tumor growth, a greater
density of CD4+ and CD8+ infiltrates in the tumor, and immune activation within tumor-draining lymph nodes. These data
suggest that a single RNA-based formulation can successfully reprogram multiple immune checkpoint interactions on a
cellular level. Such a candidate may be able to replace future immune checkpoint therapeutic regimes composed of both
stimulatory- and inhibitory-receptor-targeting antibodies.
Keywords: A1 Journal article; Pharmacology. Therapy; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 13.942
Times cited: 11
DOI: 10.1021/acsnano.1c04456
|
|
|
“Increased Performance Improvement of Lithium-Ion Batteries by Dry Powder Coating of High-Nickel NMC with Nanostructured Fumed Ternary Lithium Metal Oxides”. Herzog MJ, Gauquelin N, Esken D, Verbeeck J, Janek J, ACS applied energy materials 4, 8832 (2021). http://doi.org/10.1021/acsaem.1c00939
Abstract: Dry powder coating is an effective approach to protect the surfaces of layered cathode active materials (CAMs) in lithium-ion batteries. Previous investigations indicate an incorporation of lithium ions in fumed Al2O3, ZrO2, and TiO2 coatings on LiNi0.7Mn0.15Co0.15O2 during cycling, improving the cycling performance. Here, this coating approach is transferred for the first time to fumed ternary LiAlO2, Li4Zr3O8, and Li4Ti5O12 and directly compared with their lithium-free equivalents. All materials could be processed equally and their nanostructured small aggregates accumulate on the CAM surfaces to quite homogeneous coating layers with a certain porosity. The LiNixMnyCozO2 (NMC) coated with lithium-containing materials shows an enhanced improvement in overall capacity, capacity retention, rate performance, and polarization behavior during cycling, compared to their lithium-free analogues. The highest rate performance was achieved with the fumed ZrO2 coating, while the best long-term cycling stability with the highest absolute capacity was obtained for the fumed LiAlO2-coated NMC. The optimal coating agent for NMC to achieve a balanced system is fumed Li4Ti5O12, providing a good compromise between high rate capability and good capacity retention. The coating agents prevent CAM particle cracking and degradation in the order LiAlO2 ≈ Al2O3 > Li4Ti5O12 > Li4Zr3O8 > ZrO2 > TiO2. A schematic model for the protection and electrochemical performance enhancement of high-nickel NMC with fumed metal oxide coatings is sketched. It becomes apparent that physical and chemical characteristics of the coating significantly influence the performance of NMC. A high degree of coating-layer porosity is favorable for the rate capability, while a high coverage of the surface, especially in vulnerable grain boundaries, enhances the long-term cycling stability and improves the cracking behavior of NMCs. While zirconium-containing coatings possess the best chemical properties for high rate performances, aluminum-containing coatings feature a superior chemical nature to protect high-nickel NMCs.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Times cited: 15
DOI: 10.1021/acsaem.1c00939
|
|
|
Shaw P (2021) Dual action of reactive species as signal and stress agents in plasma medicine : combined computational and experimental research. 191 p
Abstract: Reactive oxygen and nitrogen species (RONS) generated by cold atmospheric plasma (CAP) can activate discrete signaling transduction pathways or disrupt redox cellular homeostasis, depending on their concentration. This makes that CAP possesses therapeutic potential towards wound healing, cancer, and other diseases. In order to effectively use CAP in the clinic, a clear understanding of the interaction of RONS with biomolecules (lipids, proteins and nucleic acids) from the atomic to the macro scale, and their biological significance, is needed. In this work, I have therefore studied the dual role of CAP-derived RONS, i.e., (i) in the signaling pathways involved in wound healing, and (ii) in their reaction with biomolecules to cause oxidation-mediated damage. I performed computer simulations to provide fundamental insight about the occurring processes that are difficult or even impossible to obtain experimentally. Furthermore, next to computational studies, I used both 2D and 3D tissue cultures. 3D model allows proliferation in a more physiologically relevant geometry that stimulates the production of extracellular matrix proteins. I investigated the treatment of human gingival fibroblasts with low doses of CAP-generated RONS. This treatment demonstrated that it can inhibit colony formation but does not induce cell death, induce the expression of metalloprotease proteins, induce extracellular matrix degradation, and promote cell migration, which could result in enhanced wound healing. In contrast, at high concentrations, RONS can disrupt the cell membrane integrity and induce cancer cell death through oxidative stress-mediated pathways. I discovered how oxidation of the cell membrane (lipid-peroxidation) can facilitate the access of a drug (Melittin) into cancer cells, and in this way, reduce the required therapeutic dose of Melittin in melanoma and breast cancer cells (demonstrated using in vitro, in ovo and in silico approaches). Furthermore, I studied how excessive lipid-oxidation in chemoresistant pancreatic cancer cells promotes ferroptotic cell death. This was due to the stimulation of the iron-dependent Fenton reaction by targeting a redox specific signaling network. However, upon oxidative stress, cells protect themselves via a sophisticated intracellular antioxidant system that involves the regulation of glutathione/glutathione peroxidase 4 (lipid repair enzyme). Cancer cells exhibited increased levels of intracellular RONS due to their hyper metabolism, leading to high expression of anti-oxidant systems. I therefore focus on the effect of reactive species on the intracellular anti-oxidant system and corresponding DNA damages in both temozolomide-sensitive as well as temozolomide-resistant glioblastoma spheroids, in a 3-dimensional tumor model with a more complex tumor microenvironment than cell monolayers.
Keywords: Doctoral thesis; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT); Center for Oncological Research (CORE)
|
|
|
“Understanding and optimizing Evolon®, CR for varnish removal from oil paintings”. Baij L, Liu C, Buijs J, Alvarez Martin A, Westert D, Raven L, Geels N, Noble P, Sprakel J, Keune K, Heritage science 9, 155 (2021). http://doi.org/10.1186/S40494-021-00627-9
Keywords: A1 Journal article; Engineering sciences. Technology; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation); Antwerp X-ray Imaging and Spectroscopy (AXIS)
DOI: 10.1186/S40494-021-00627-9
|
|
|
“Novel thin film lift-off process for in situ TEM tensile characterization”. Neelisetty KK, Kumar CN S, Kashiwar A, Scherer T, Chakravadhanula VSK, Kuebel C, Microscopy And Microanalysis 27, 216 (2021). http://doi.org/10.1017/S1431927621001367
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 1.891
DOI: 10.1017/S1431927621001367
|
|
|
“&alpha, phase growth and branching in titanium alloys”. Shi R, Choudhuri D, Kashiwar A, Dasari S, Wang Y, Banerjee R, Banerjee D, Philosophical magazine (2021). http://doi.org/10.1080/14786435.2021.1998693
Abstract: The morphology and spatial distribution of alpha (α) precipitates have been mapped as a function of Mo content in Ti-Mo binary alloys employing a combinatorial approach. Heat-treatments were carried out on compositionally graded Ti-xMo samples processed using a rapid throughput laser engineered net shape (LENS) process. The composition space spans 1.5 at% to 6 at% Mo with ageing at 750°C, 650°C and 600°C following a β solution treatment. Three distinct regimes of α morphology and distribution were observed. These are colony-dominated microstructures originating from grain boundary α allotriomorphs, bundles of intragranular α laths, and homogeneously distributed individual fine-scale α laths. Branching of the α precipitates was observed in all these domains in a manner reminiscent of solid-state dendritic growth. The phenomenon is particularly apparent at low volume fractions of α. Similar features are present in a wide variety of alloy compositions. 3-dimensional features of such branched structures have been analysed. Simulation of the branching process by phase field methods incorporating anisotropy in the α/β interface energy and elasticity suggests that it can be initiated at growth ledges present at broad faces of the α laths, driven by the enhancement of the diffusion flux at these steps. The dependence of branching on various parameters such as supersaturation and diffusivity, and microstructural features like ledge height and distribution and the presence of adjacent α variants has been evaluated.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 1.505
DOI: 10.1080/14786435.2021.1998693
|
|
|
Peeters M (2021) The added value of Smart Product-Service Systems to real estate developments. 117 p
Abstract: Socially responsible investments can be defined as an investment process that integrates ethical values and environmental protection, improving social conditions, and good governance into a traditional investment decision. This integration is mainly a consequence of the growing importance that investors give to environmental, social, and governance (ESG) criteria, resulting in more sustainable development. Also, in the real estate sector, increased attention is being paid to the contributions made to integrate economic, environmental, and social factors into decisions. The ESG framework looks closely at how companies are managed, and the impact related to their market value. The factors for investors’ focus are summarized as environmental, social, and governance. The term ESG was coined in a 2004 United Nations (UN) report titled “Who Cares Wins,” aimed at raising awareness regarding the importance of environmental, social, and corporate governance issues in financial markets. The ESG criteria’s specific purpose is to guide investors in recognizing sustainable investments without evaluating how sustainable the asset is or the investment value represented by sustainability. It is essential to underline that ESG does not take specific economic interests into account. The rationale behind this apparent gap is that investors investigate the economic aspects before investing. However, by not explicitly linking ESG and economic criteria, attractive investments are often misjudged and not implemented. For example, investments that only show their value in the longer term or indirectly influence value by achieving a higher retention rate among incumbent tenants, reducing or eliminating friction costs. A product–service system (PSS) refers to a market proposition (business model) that builds on a product’s traditional functionality by incorporating additional services. Although services are already offered, the PSS function is to link the service to a product. The service thereby supports the operation of the product and generates additional benefits. It encompasses the integrated solutions of products and services to satisfy customers' needs and generate maximum value. According to Sutanto et al., a PSS is designed to focus on sustainability characterized in three dimensions. 1. The economic dimension 2. The environmental dimension 3. The social dimension When discussing sustainability in this thesis, we use the criteria listed above related to socially responsible investments. The link between PSS and ESG is that a PSS focuses on creating a sustainable system, and ESG makes sustainability more visible to investors. Therefore, when PSS are recognized and implemented in buildings, they must be evaluated using ESG analysis methods. Product-Service Systems (PSS) try to find a way to offer services on top of a product. The product is essentially secondary to the result that is delivered from the services. For example, the modem (product) that a cable company provides will be of secondary importance to the connectivity (service). Alternatively, it will be less critical how heat is made (product) than the intended set point is achieved in the building. PSSs transform the supply of products into services. In doing so, the responsibility shifts from delivering a product (once only) to continuous service delivery. Therefore, it is in the best interest of the service provider to deliver the outcome of the service as efficiently (read: lowest cost) as possible. A direct consequence of this is that the service provider will want to use the product as efficiently as possible and as long as possible to reduce his costs. Therefore, the supplier will also want to recover and maximize the reuse of his product based on the same rationale. A positive impact on the environment and the used raw materials is thus to be expected. The whole process of servitization (transforming products into services) in real estate will positively impact the Economic, Environmental and Social factors. Therefore, demonstrating this proposition is the main objective of this thesis. Smart PSS is the same idea as Product-Service systems but in which the digitization of the services plays a key role. It will be shown that by digitizing services, a broader range can be offered. It will be demonstrated that products that provide services at the building level can, through their interconnectedness, also provide services to external systems (e.g. electricity grid, urban planning, mobility, ...). At the same time, digitizing the products and services will also underpin trust in the systems and allow for proper remuneration. In this PhD, different standard systems in a building, such as the reservation system, the water heater, or the fire detection system, are equipped with additional services. A PSS is often specifically designed to focus on economic, social, and environmental dimensions. These dimensions correspond to the investor’s examination as part of the ESG analysis before investing. As the PSS is often specifically designed to integrate sustainability, there is a close link between the sustainability performance of the PSS and the ESG criteria evaluated by the investor. Throughout the work, the owner is considered to be the user of the building. It is not the case that only an owner-user can generate cash flow. In essence, if they have sufficient rights to the underlying product, any building user can activate services that generate cash flow. In today's market, it is logical that this is viewed in the owner-user context as they will usually choose the products to be installed in larger technical installations. They may have previously used a PSS or choose to move to one. However, a building’s tenant could choose to lease out their meeting rooms if they are not contractually prohibited from doing so since, in practice, contracts have begun to prohibit certain services. For example, rental contracts that actively prohibit renting out a property through platforms such as Airbnb. Thus, the user’s function could potentially impact how the PSS is designed. This work does not explicitly explore the impact of this aspect. The owner-user is assumed throughout this manuscript. The second chapter describes the state of affairs concerning PSSs in a broad framework evolving towards focusing on the real estate sector. After which, in the second chapter, ESG and the link to real estate and how smart real estate (smart buildings) is missing from this evaluation are discussed in more detail. Chapter 3 shows from a fire alarm system, which was extended with an evacuation support system, the usefulness, and the risk of data. Further work was done to demonstrate the added value in terms of Economic, Environmental and Social factors of standard installations in buildings. In Chapter 4, a simple sanitary hot water boiler is extended with a service that allows controlling this boiler according to the status of the electricity grid (surplus or shortage of energy). The supply and demand of energy on the power grid must be equal at all times. By equipping a classic water heater (product) with additional intelligence (service), it becomes possible to adjust the energy use to the grid's needs. The grid operators are prepared to pay for this. This payment can be linked to different energy markets (long term market, spot market, ...). This study looked at the fee that would have to be paid when the adjustment of the energy use can be made instantaneously so that the fee must be settled according to the prices on the imbalance market. In chapter 5, we look at the impact of the service to rent out free spaces as co-working places on a broad market (external to the building), compared to a regular reservation system. By renting out unused workplaces on a broad market, the utilization of the existing patrimony will be higher. The demand for new square meters with the same function will decrease as the supply-demand curve changes, and so will the price. This makes it less interesting to build new buildings. Less construction of new buildings will result in fewer resources being used, which will positively affect the environment. In addition, fewer new buildings with an office function will leave more space for buildings with another function. Also, the city's infrastructure will be less burdened (roads, sewerage, electricity grid,...). In The Hague, the decreasing need for new square meters of office buildings can lead to more space for affordable housing, for which the city has a great need. Chapter 6 will frame the valuation of service as a real options method that gives an impetus to a general valuation methodology to value the flexibility that Smart PSS inherently has. Finally, this thesis demonstrates that (smart) PSSs impact real estate profitability, while positively influencing environmental and social factors. Further research and the limitations of the studies conducted are documented. This PhD concludes that Product-Service systems should break the silos between different stakeholders, resulting in a lower total cost of ownership of buildings in the longer term. This can only be achieved if the valuation of Product-Service systems is done correctly and is recognized by every stakeholder in the real estate process.
Keywords: Doctoral thesis; Economics; Engineering Management (ENM); Internet Data Lab (IDLab)
|
|