Abstract: The latest life-cycle assessment methods account for land use, due to the production, use and disposal of products and services, in terms of ecosystem damage. The process of brownfield remediation converts otherwise idle urban space into productive space. The value to ecosystems in this context is of course limited since the brownfield site remains urban. When evaluating brownfield remediation technologies, the availability of space on-site is dependent on the duration of time required by the remediation technology to reach the remediation target. Remediation technology alternatives tend to vary largely in terms of duration. Comparative life-cycle assessments of remediation technologies, to date, present the large variations between alternatives in terms of remediation duration but do not translate this into an impact or parameter. The restored subsurface zone is often defined as a functional unit, when in fact the surface area is the resource restored by the remediation service. The economic benefits of making land resources available are particularly important considerations in the context of brownfield remediation. The research proposes an innovative impact assessment approach that allows land to be considered as a finite resource. The method is applied in a comparative life-cycle assessment of two potential remediation scenarios for an idle brownfield in the Brussels region of Belgium. The results show that there is a trade-off between greenhouse gas emissions and land availability and that both are largely dependent on the efficiency of the contaminant extraction mechanism. The results also raise the question as to whether the economic valuation of land, like precious metals and fossil fuels, provides an accurate reflection of the true value of the resource. Considering land as a resource at the midpoint level is also relevant in other urban contexts where competition exists between different land-uses, where urban sprawl is detrimental to undeveloped areas and where urban intensification is a policy objective. (C) 2015 Elsevier Ltd. All rights reserved.

Abstract: In the present study, an active site titration method is demonstrated, to determine the amount of active enzyme (beta-galactosidase), immobilized on a support. Two types of supports were investigated, viz, amino acrylic resin and a mixed matrix membrane. Furthermore, 2',4'-dinitrophenyl 2-deoxy-2-fluoro-beta-D-galactopyranoside was used as an inhibitor for the active site titration of immobilized beta-galactosidase obtained from Kluyveromyces lactis. Using the active site titration, approximately 8.3 mg of active enzyme was found on 1 g of dried commercially available SPRIN imibond, which is an amino acrylic resin with covalently bound beta-galactosidase obtained from K. lactis. However, this method, in its present form, was not effective on the mixed matrix membranes due to the irreversible partial adsorption of the leaving group (2',4'-dinitrophenolate) by the membrane. This observation implied that it is important to investigate interactions between the support and the used inhibitor and leaving group. (C) 2014 Elsevier B.V. All rights reserved.

Abstract: Organic carbon introduction in the soil to initiate remedial measures, nitrate infiltration due to agricultural practices or sulphate intrusion owing to industrial usage can influence the redox conditions and pH, thus affecting the mobility of heavy metals in soil and groundwater. This study reports the fate of Zn and Cd in sandy aquifers under a variety of plausible in-situ redox conditions that were induced by introduction of carbon and various electron acceptors in column experiments. Up to 100% Zn and Cd removal (from the liquid phase) was observed in all the four columns, however the mechanisms were different. Metal removal in column K1 (containing sulphate), was attributed to biological sulphate reduction and subsequent metal precipitation (as sulphides). In the presence of both nitrate and sulphate (K2), the former dominated the process, precipitating the heavy metals as hydroxides and/or carbonates. In the presence of sulphate, nitrate and supplemental iron (Fe(OH)(3)) (K3), metal removal was also due to precipitation as hydroxides and/or carbonates. In abiotic column, K4, (with supplemental iron (Fe(OH)(3)), but no nitrate), cation exchange with soil led to metal removal. The results obtained were modeled using the reactive transport model PHREEQC-2 to elucidate governing processes and to evaluate scenarios of organic carbon, sulphate and nitrate inputs. (C) 2010 Elsevier B.V. All rights reserved.

Abstract: As a part of the NASA Global Tropospheric Experiment (GTE), aerosols were sampled in the tropical rain forest of the Amazon Basin during the Amazon Boundary Layer Experiment (ABLE 2B) in April and May 1987, in the wet season, when no forest burning occurs. Fine (dp < 2.0 μm) and coarse (2.0 < dp < 15 μm) aerosol fractions were collected using stacked filter units, at three sites under the forest canopy and at three levels of a tower inside the jungle. Particle-induced X ray emission (PIXE) was used to measure concentrations of 22 elements (Na, Mg, Al, Si, P, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Br, Rb, Sr, Zr, and Pb). Morphological and trace element measurements of individual particles were carried out by automated electron probe X ray microanalysis. Gravimetric analysis was performed to obtain the fine and coarse aerosol mass concentration. Absolute factor analysis was used to interpret the large data set of the trace element concentrations and to obtain elemental source profiles. Hierarchical cluster analysis was used to derive groups of individual particles. The concentrations of soil dust related elements (Al, Si, Ti, Fe, Mn) were 5 times larger in the wet season compared to the 1985 ABLE 2A dry season experiment. Biogenic aerosol related elements in the fine fraction showed lower concentrations in the wet season. Fine aerosol mass concentration averaged only 2.1±0.7 μg m−3, while the average coarse mass concentration was 6.1±1.8 μg m −3. Sulphur concentrations averaged 76±14 ng m −3 in the fine fraction and 37±9 ng m −3 in the coarse fraction. Biogenic aerosol-related elements were dominant under the forest canopy, while soil dust dominated at the top of the forest canopy. Only two factors explained about 90% of the data variability for the fine and coarse aerosol fractions. These were soil dust (represented mainly by Al, Si, Ti, Mn, and Fe) and biogenic aerosol (represented by K, P, Cl, S, Zn, and the aerosol mass concentration). Source profiles showed a homogeneous aerosol distribution with similar elemental compositions at the different sampling sites. Enrichment factor calculations revealed a soil dust elemental profile similar to the average bulk soil composition, and a biogenic component similar to the plant bulk elemental composition. Total aerosol mass source apportionment showed that biogenic particles account for 5595% of the airborne concentrations. The analysis of individual aerosol particles showed that the biogenic particles consist of leaf fragments, pollen grains, fungi, algae, and other types of particles. Several groups of particles with K, Cl, P, S, and Ca as minor elements could easily be identified as biogenic particles on the basis of their morphology. Considering the vast area of tropical rain forests and the concentrations measured in this work, it is possible that biogenic particles can play an important role in the global aerosol budget and in the global biogeochemical cycles of various elements.

Abstract: Between 15 January and 26 February 1987, 51 fine and coarse mode aerosol samples were collected at the Universidad de Santiago de Chile Planetarium using a dichotomous sampler. The samples were analyzed by X-ray fluorescence for up to 17 elements (Mg, Al, Si, P, S, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Br and Pb). Aerosol particles were individually studied by Electron Probe Microanalysis (EPMA) and Laser Microprobe Mass Analysis (LAMMA). The data set consisting of aerosol elemental concentrations and meteorological variables was subjected to Principal Factor Analysis (PFA), allowing the identification of six fine mode particle source classes (soil, industrial, sulfate particles, traffic, residual oil, wood-burnings), and five coarse mode particle source classes (soil, industrial, traffic, residual oil, sulfate particles). Both PFA solutions explained about 81 and 90% of the total variance in the data set, respectively. The regression of elemental mass concentrations on the Absolute Principal Factor Scores allowed the estimation of the contribution of the different source classes to the Santiago aerosol. Within the fine fraction, secondary SO42− particles were responsible for about 49% of the fine mode aerosol mass concentration, while 26, 13, 6.4 and 5.6% were attributed to wood-burning/car exhausts, residual oil combustion, soil dust/metallurgical, and soil dust/wood-burning releases, respectively. The coarse fraction source apportionment was mainly dominated by soil dust, accounting for 74% of the coarse mode aerosol mass concentration. A composite of soil dust and industrial release accounted for 13%; a composite of secondary sulfates contributed with 9%; a composite of soil dust and automotive emissions, and secondary sulfates were responsible for 4 and 0.03% of the coarse aerosol mass concentration, respectively. EPMA results are in satisfactory agreement with those from the bulk analysis and allowed the identification of eight particle types in both fine and coarse mode aerosols, pertaining to different source classes, namely soil, seaspray, secondary SO42−, metallurgical emissions and biomass burning release. EPMA also evidenced that one of the most abundant particle types corresponded to marine aerosol, having an average diameter of 0.7 μm for the fine mode and 2.2 μm for the coarse mode aerosol. LAMMA results indicate that, in fact, seaspray has been transported into the city of Santiago de Chile airshed, suffering several transformations and a sulfur enrichment. This analytical technique also provided evidence of the abundance of carbon-rich particles, which were not detected by either the bulk X-ray analysis or EPMA; they are probably due to fossil-fuel combustion releases.

Abstract: Different trace- and microanalytical techniques were used in an extensive study to elucidate the chemical deterioration process of the sandy-limestone St Rombouts Cathedral in Mechelen, Belgium. Samples of stones, mortar joints, slates, atmospheric aerosols and gases, total and wet deposition, and water that had run down the cathedral walls, were all thoroughly characterized. At the east side, usually not exposed to precipitation, a 3001000-μm thick outer crust of microcrystalline gypsum was observed, while at the west side, this surface layer was mostly eroded away due to precipitation. At the north and south sides, the crust contains varying amounts of gypsum and calcite. The gypsum is mostly present in a bar-shaped morphology and carbonaceous fly-ash particles were rarely found in the weathering crust. Local stone characteristics seem to be extremely important in relation to the gypsum content of the crust; black samples always have a much higher sulphate content than the corresponding white samples, irrespective of the predominant direction of orientation. The relative contribution of nitrogen- and chlorine-containing pollutants to the total decay process is much smaller than that of sulphur-containing pollutants. Deposition samples collected at the site of the cathedral mostly had a pH of > 5.6, due to the neutralization of the rainwater by alkaline atmospheric constituents. Runoff water and washdown water were enriched in all ions, especially Ca2+ and SO42−, indicating that, indeed, gypsum is the most important weathering product. The suspension in deposition samples and black-well leaching water was highly enriched in silicon-containing particles, while runoff water and white-wall leaching water contained a predominant calcium-rich suspension.

Abstract: Methods used to strengthen metals generally also cause a pronounced decrease in ductility and electrical conductivity. In this work a bioinspired strategy is applied to surmount the dilemma. By assembling copper submicron flakes cladded with in-situ grown graphene, graphene/copper matrix composites with a nanolaminated architecture inspired by a natural nacre have been prepared. Owing to a combined effect-from the bioinspired nanolaminated architecture and improved interfacial bonding, a synergy has been achieved between mechanical strength and ductility as well as electrical conductivity in the graphene/copper matrix composites. With a low volume fraction of only 2.5% of graphene, the composite shows a yield strength and elastic modulus similar to 177% and similar to 25% higher than that of unreinforced copper matrix, respectively, while retains ductility and electrical conductivity comparable to that of pure copper. The bioinspired nanolaminated architecture enhances the efficiencies of two-dimensional (2D) graphene in mechanical strengthening and electrical conducting by aligning graphene to maximize performance for required loading and carrier transporting conditions, and toughens the composites by crack deflection. Meanwhile, in-situ growth of graphene is beneficial for improving interfacial bonding and structural quality of graphene. The strategy sheds light on the development of composites with good combined structural and functional properties. (C) 2017 Elsevier Ltd. All rights reserved.

Abstract: A novel class of supershaped dielectric lens antennas, whose geometry is described by the three-dimensional (3D) Gielis formula, is introduced and analysed. To this end, a hybrid modelling approach based on geometrical and physical optics is adopted in order to efficiently analyse the multiple wave reflections occurring within the lens and to evaluate the relevant impact on the radiation properties of the antenna under analysis. The developed modelling procedure has been validated by comparison with numerical results already reported in the literature and, afterwards, applied to the electromagnetic characterisation of Gielis dielectric lens antennas with shaped radiation pattern. Furthermore, a dedicated optimisation algorithm based on quantum particle swarm optimisation has been developed for the synthesis of 3D supershaped lens antennas with single feed, as well as with beamforming capabilities.

Abstract: A diffusive sampling method for the determination of gaseous acetic and formic acids, using a radial symmetry diffusive sampler, has been optimised for a 7-day exposure time in this study. Sampling rate determinations were performed on data obtained from a dynamic exposure chamber, simulating the indoor conditions of an empty, closed, room, at room temperature and minimal wind speed. Analysis has been performed by means of ion chromatography. The sampling rates for formic acid concentrations of 128 ìg m−3 and 1248 ìg m−3 were determined to be 91.2 ± 3.9 ml min−1 and 111.6 ± 2.8 ml min−1, respectively. The acetic acid sampling rate was independent of the concentration in the range 160 ìg m−31564 ìg m−3, and amounted to 97.3 ± 3.1 ml min−1. Experimentally determined sampling rates showed deviations of 3% for acetic acid, and 321% for formic acid, in relation to theoretically derived values. The blank values were as low as 1.69 ± 0.07 ìg for formic acid and 1.21 ± 0.14 ìg for acetic acid, and detection limits lower than 0.5 ìg m−3 could be achieved, which is an improvement of 9899% compared to previously validated diffusive sampling methods. This study describes the first step of an extended validation program in which the applicability of these types of samplers for the measurement of organic acids will be validated and optimised for the environmental conditions typical for museum showcases.

Abstract: Mineral monazite from Malaysia has been investigated by energy dispersive x-ray analysis employing three different methods: x-ray, relativistic electron and proton induced excitation. An upper limit of 15 ppm has been placed on the possible concentration of the superheavy element with Z=126.