Records |
Author |
Schryvers, D.; Lahjouji, D.E.; Slootmaekers, B.; Potapov, P.L. |
Title |
HREM investigation of martensite precursor effects and stacking sequences in Ni-Mn-Ti alloys |
Type |
A1 Journal article |
Year |
1996 |
Publication |
Scripta metallurgica et materialia |
Abbreviated Journal |
Scripta Mater |
Volume |
35 |
Issue |
|
Pages |
1235-1241 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
New York |
Editor |
|
Language |
|
Wos |
A1996VL92800019 |
Publication Date |
2002-07-26 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1359-6462; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.224 |
Times cited |
2 |
Open Access |
|
Notes |
|
Approved |
no |
Call Number |
UA @ lucian @ c:irua:15427 |
Serial |
1506 |
Permanent link to this record |
|
|
|
Author |
Cautaerts, N.; Delville, R.; Stergar, E.; Schryvers, D.; Verwerft, M. |
Title |
Tailoring the Ti-C nanoprecipitate population and microstructure of titanium stabilized austenitic steels |
Type |
A1 Journal article |
Year |
2018 |
Publication |
Journal of nuclear materials |
Abbreviated Journal |
J Nucl Mater |
Volume |
507 |
Issue |
507 |
Pages |
177-187 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
The present work reports on the microstructural evolution of a new heat of 24% cold worked austenitic DIN 1.4970 (15-15Ti) nuclear cladding steel subjected to ageing heat treatments of varying duration between 500 and 800 degrees C (by steps of 100 degrees C). The primary aim was studying the finely dispersed Ti-C nanoprecipitate population, which are thought to be beneficial for creep and swelling resistance during service. Their size distribution and number density were estimated through dark field imaging and bright field Moire imaging techniques in the transmission electron microscope. Nanoprecipitates formed at and above 600 degrees C, which is a lower temperature than previously reported. The observed nucleation, growth and coarsening behavior of the nanoprecipitates were consistent with simple diffusion arguments. The formation of nanoprecipitates coincided with significant dissociation of dislocations as evidenced by weak beam dark field imaging. Possible mechanisms, including Silcock's stacking fault growth model and Suzuki segregation, are discussed. Recrystallization observed after extended ageing at 800 degrees C caused the redissolution of nanoprecipitates. Large primary Ti(C,N) and (Ti,Mo)C precipitates that occur in the as-received material, and M23C6 precipitates that nucleate on grain boundaries at low temperatures were also characterized by a selective dissolution procedure involving filtration, X-ray diffraction and quantitative Rietveld refinement. The partitioning of key elements between the different phases was derived by combining these findings and was consistent with thermodynamic considerations and the processing history of the steel. (C) 2018 Elsevier B.V. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
Language |
|
Wos |
000438019800021 |
Publication Date |
2018-04-30 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0022-3115 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.048 |
Times cited |
1 |
Open Access |
Not_Open_Access |
Notes |
; We would like to acknowledge ENGIE, SCK.CEN, the SCK.CEN academy and the MYRRHA project for the financial support of this work. Special thanks to T. Wangle and P. Dries for their help with filtration and gravimetry. Also thanks to Dr. G. Leinders for the discussions on XRD and Rietveld refinement. Thanks to E. Charalampopoulou and A. Youssef for assisting with the dissolution experiments. ; |
Approved |
Most recent IF: 2.048 |
Call Number |
UA @ lucian @ c:irua:152382 |
Serial |
5043 |
Permanent link to this record |
|
|
|
Author |
Du, C.; Hoefnagels, J.P.M.; Kolling, S.; Geers, M.G.D.; Sietsma, J.; Petrov, R.; Bliznuk, V.; Koenraad, P.M.; Schryvers, D.; Amin-Ahmadi, B. |
Title |
Martensite crystallography and chemistry in dual phase and fully martensitic steels |
Type |
A1 Journal article |
Year |
2018 |
Publication |
Materials characterization |
Abbreviated Journal |
Mater Charact |
Volume |
139 |
Issue |
|
Pages |
411-420 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
Lath martensite is important in industry because it is the key strengthening component in many advanced high strength steels. The study of crystallography and chemistry of lath martensite is extensive in the literature, however, mostly based on fully martensitic steels. In this work, lath martensite in dual phase steels is investigated with a focus on the substructure identification of the martensite islands and microstructural bands using electron backscattered diffraction, and on the influence of the accompanied tempering process during industrial coating process on the distribution of alloying elements using atom probe tomography. Unlike findings for the fully martensitic steels, no martensite islands with all 24 Kurdjumov-Sachs variants have been observed. Almost all martensite islands contain only one main packet with all six variants and minor variants from the remaining three packets of the same prior austenite grain. Similarly, the martensite bands are typically composed of connected domains originating from prior austenite grains, each containing one main packets (mostly with all variants) and few separate variants. The effect of tempering at similar to 450 degrees C (due to the industrial zinc coating process) has also been investigated. The results show a strong carbon partitioning to lath boundaries and Cottrell atmospheres at dislocation core regions due to the thermal process of coating. In contrast, auto-tempering contributes to the carbon redistribution only in a limited manner. The substitutional elements are all homogenously distributed. The phase transformation process has two effects on the material: mechanically, the earlier-formed laths are larger and softer and therefore more ductile (as revealed by nanoindentation); chemically, due to the higher dislocation density inside the later-formed laths, which are generally smaller, carbon Cottrell atmospheres are predominantly observed. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
New York |
Editor |
|
Language |
|
Wos |
000431469300044 |
Publication Date |
2018-03-09 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1044-5803 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.714 |
Times cited |
|
Open Access |
Not_Open_Access |
Notes |
|
Approved |
Most recent IF: 2.714 |
Call Number |
UA @ lucian @ c:irua:151554 |
Serial |
5033 |
Permanent link to this record |
|
|
|
Author |
Radi, A.; Khalil-Allafi, J.; Etminanfar, M.R.; Pourbabak, S.; Schryvers, D.; Amin-Ahmadi, B. |
Title |
Influence of stress aging process on variants of nano-N4Ti3precipitates and martensitic transformation temperatures in NiTi shape memory alloy |
Type |
A1 Journal article |
Year |
2018 |
Publication |
Materials & design |
Abbreviated Journal |
Mater Design |
Volume |
262 |
Issue |
262 |
Pages |
74-81 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
In this study, the effect of a stress aging process on the microstructure and martensitic phase transformation of NiTi shape memory alloy has been investigated. NiTi samples were aged at 450 degrees C for 1 h and 5 h under different levels of external tensile stress of 15, 60 and 150 MPa. Transmission electron microscopy (TEM) was used to characterize different variants and morphology of precipitates. The results show that application of all stress levels restricts the formation of precipitates variants in the microstructure after I h stress aging process. However, all variants can be detected by prolonging aging time to 5 h at 15 MPa stress level and the variants formation is again restricted by increasing the stress level. Moreover, the stress aging process resulted in changing the shape of precipitates in comparison with that of the stress-free aged samples. Coffee-bean shaped morphologies were detected for precipitates in all stress levels. According to the Differential Scanning Calorimetry (DSC) results, the martensite start temperature (M-s) on cooling shifts to higher temperatures with increasing the tensile stress during the aging process. This can be related to the change ofaustenite to martensite interface energy due to the different volume fractions and variants of precipitates. (c) 2018 Elsevier Ltd. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
|
Publication Date |
2018-01-04 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0264-1275 |
ISBN |
|
Additional Links |
UA library record; ; WoS full record; WoS citing articles |
Impact Factor |
4.364 |
Times cited |
|
Open Access |
OpenAccess |
Notes |
|
Approved |
Most recent IF: 4.364 |
Call Number |
UA @ lucian @ c:irua:149854 |
Serial |
4938 |
Permanent link to this record |
|
|
|
Author |
Idrissi, H.; Bollinger, C.; Boioli, F.; Schryvers, D.; Cordier, P. |
Title |
Low-temperature plasticity of olivine revisited with in situ TEM nanomechanical testing |
Type |
A1 Journal article |
Year |
2016 |
Publication |
Science Advances |
Abbreviated Journal |
|
Volume |
2 |
Issue |
2 |
Pages |
e1501671-e1501671 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
The rheology of the lithospheric mantle is fundamental to understanding how mantle convection couples with plate tectonics. However, olivine rheology at lithospheric conditions is still poorly understood because experiments are difficult in this temperature range where rocks and mineral become very brittle. We combine techniques of quantitative in situ tensile testing in a transmission electron microscope and numerical modeling of dislocation dynamics to constrain the low-temperature rheology of olivine. We find that the intrinsic ductility of olivine at low temperature is significantly lower than previously reported values, which were obtained under strain-hardened conditions. Using this method, we can anchor rheological laws determined at higher temperature and can provide a better constraint on intermediate temperatures relevant for the lithosphere. More generally, we demonstrate the possibility of characterizing the mechanical properties of specimens, which can be available in the form of submillimeter-sized particles only. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000379620200043 |
Publication Date |
2016-03-12 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
2375-2548 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
32 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: NA |
Call Number |
UA @ lucian @ c:irua:134983 |
Serial |
4202 |
Permanent link to this record |
|
|
|
Author |
Schryvers, D.; Van Tendeloo, G.; van Landuyt, J.; Amelinckx, S. |
Title |
Some examples of electron microscopy studies of microstructures and phase transitions in solids |
Type |
A1 Journal article |
Year |
1995 |
Publication |
Meccanica |
Abbreviated Journal |
Meccanica |
Volume |
30 |
Issue |
|
Pages |
433-438 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Milano |
Editor |
|
Language |
|
Wos |
A1995TD08800003 |
Publication Date |
2005-04-21 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0025-6455;1572-9648; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
1.949 |
Times cited |
1 |
Open Access |
|
Notes |
|
Approved |
CHEMISTRY, PHYSICAL 77/144 Q3 # MATHEMATICS, INTERDISCIPLINARY 19/101 Q1 # PHYSICS, ATOMIC, MOLECULAR & CHEMICAL 17/35 Q2 # |
Call Number |
UA @ lucian @ c:irua:13170 |
Serial |
3054 |
Permanent link to this record |
|
|
|
Author |
Schryvers, D.; Ma, Y. |
Title |
The growth of Ni5Al3 in L10 martensite studied by in situ transmission electron microscopy and high resolution electron microscopy |
Type |
A1 Journal article |
Year |
1995 |
Publication |
Journal of alloys and compounds |
Abbreviated Journal |
J Alloy Compd |
Volume |
221 |
Issue |
|
Pages |
227-234 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
Language |
|
Wos |
A1995QZ73800044 |
Publication Date |
2002-07-25 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0925-8388; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.999 |
Times cited |
19 |
Open Access |
|
Notes |
|
Approved |
no |
Call Number |
UA @ lucian @ c:irua:13169 |
Serial |
1397 |
Permanent link to this record |
|
|
|
Author |
Schryvers, D. |
Title |
SAED and HREM results suggest a NiTi B19' based superstructure for CuZr martensite |
Type |
A1 Journal article |
Year |
1995 |
Publication |
Journal de physique: colloques, suppléments |
Abbreviated Journal |
|
Volume |
5 |
Issue |
8 |
Pages |
1047-1052 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Les Ulis |
Editor |
|
Language |
|
Wos |
A1995TX21300085 |
Publication Date |
2014-07-16 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1155-4339; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
2 |
Open Access |
|
Notes |
|
Approved |
MATERIALS SCIENCE, MULTIDISCIPLINARY 96/271 Q2 # |
Call Number |
UA @ lucian @ c:irua:13168 |
Serial |
2939 |
Permanent link to this record |
|
|
|
Author |
Schryvers, D.; Toth, L.; van Humbeeck, J.; Beyer, J. |
Title |
Ni2Al versus Ni5Al3 ordering in Ni65Al35 austenite and martensite |
Type |
A1 Journal article |
Year |
1995 |
Publication |
Journal de physique: colloques, suppléments |
Abbreviated Journal |
|
Volume |
5 |
Issue |
8 |
Pages |
1029-1034 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Les Ulis |
Editor |
|
Language |
|
Wos |
A1995TX21300082 |
Publication Date |
2014-07-16 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1155-4339; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
12 |
Open Access |
|
Notes |
|
Approved |
PHYSICS, APPLIED 47/145 Q2 # |
Call Number |
UA @ lucian @ c:irua:13167 |
Serial |
3548 |
Permanent link to this record |
|
|
|
Author |
Schryvers, D.; Ma, Y. |
Title |
In-situ TEM study of the Ni5Al3 to B2 + L12 decomposition in Ni65Al35 |
Type |
A1 Journal article |
Year |
1995 |
Publication |
Materials letters |
Abbreviated Journal |
Mater Lett |
Volume |
23 |
Issue |
|
Pages |
105-111 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Homogenised and quenched Ni65Al35 samples were heated and studied in situ in a CM20 electron microscope up to 900 degrees C. The Ni5Al3 phase first forming around 550 degrees C in the quenched L1(0) microtwinned martensite starts to decompose around 800 degrees C yielding B2 precipitates in a twinned L1(2) matrix. The latter twinning is a remainder of the microtwinning in the original room temperature martensite. Also the crystallographic relations between precipitates and matrix can be traced back to the original formation of twinned martensite plates within the austenite. Some aspects of the dynamics of the process are discussed on the basis of snap shots and video recordings. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
Language |
|
Wos |
A1995QW53500020 |
Publication Date |
2002-07-25 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0167-577X; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.489 |
Times cited |
5 |
Open Access |
|
Notes |
|
Approved |
no |
Call Number |
UA @ lucian @ c:irua:13166 |
Serial |
1585 |
Permanent link to this record |
|
|
|
Author |
Schryvers, D.; Ma, Y.; Toth, L.; Tanner, L.E. |
Title |
Electron microscopy study of the formation of Ni5Al3 in a Ni62.5Al37.5 B2 alloy: 2: plate crystallography |
Type |
A1 Journal article |
Year |
1995 |
Publication |
Acta metallurgica et materialia |
Abbreviated Journal |
|
Volume |
43 |
Issue |
11 |
Pages |
4057-4065 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
New York |
Editor |
|
Language |
|
Wos |
A1995TA33200015 |
Publication Date |
2003-12-05 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0956-7151; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
11 |
Open Access |
|
Notes |
|
Approved |
no |
Call Number |
UA @ lucian @ c:irua:13165 |
Serial |
974 |
Permanent link to this record |
|
|
|
Author |
Schryvers, D.; Ma, Y.; Toth, L.; Tanner, L.E. |
Title |
Electron microscopy study of the formation of Ni5Al3 in a Ni62.5Al37.5 B2 alloy: 1: precipitation and growth |
Type |
A1 Journal article |
Year |
1995 |
Publication |
Acta metallurgica et materialia |
Abbreviated Journal |
|
Volume |
43 |
Issue |
11 |
Pages |
4045-4056 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
New York |
Editor |
|
Language |
|
Wos |
A1995TA33200014 |
Publication Date |
2003-12-05 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0956-7151; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
27 |
Open Access |
|
Notes |
|
Approved |
no |
Call Number |
UA @ lucian @ c:irua:13164 |
Serial |
973 |
Permanent link to this record |
|
|
|
Author |
Goessens, C.; Schryvers, D.; van Landuyt, J.; Millan, A.; de Keyzer, R. |
Title |
Electron microscopical investigation of AgBr needle crystals |
Type |
A1 Journal article |
Year |
1995 |
Publication |
Journal of crystal growth |
Abbreviated Journal |
J Cryst Growth |
Volume |
151 |
Issue |
|
Pages |
335-341 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
Language |
|
Wos |
A1995RE62100017 |
Publication Date |
2003-05-19 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0022-0248; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
1.698 |
Times cited |
14 |
Open Access |
|
Notes |
|
Approved |
MATERIALS SCIENCE, MULTIDISCIPLINARY 135/271 Q2 # PHYSICS, APPLIED 70/145 Q2 # PHYSICS, CONDENSED MATTER 40/67 Q3 # |
Call Number |
UA @ lucian @ c:irua:13163 |
Serial |
941 |
Permanent link to this record |
|
|
|
Author |
Goessens, C.; Schryvers, D.; van Landuyt, J.; Amelinckx, S.; de Keyzer, R. |
Title |
Long period surface ordering of iodine ions in mixed tabular AgBr-AgBrI microcrystals |
Type |
A1 Journal article |
Year |
1995 |
Publication |
Surface science : a journal devoted to the physics and chemistry of interfaces |
Abbreviated Journal |
Surf Sci |
Volume |
337 |
Issue |
|
Pages |
153-165 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
Language |
|
Wos |
A1995RQ74900024 |
Publication Date |
2003-05-13 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0039-6028; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
1.925 |
Times cited |
10 |
Open Access |
|
Notes |
|
Approved |
no |
Call Number |
UA @ lucian @ c:irua:13162 |
Serial |
1836 |
Permanent link to this record |
|
|
|
Author |
Boulay, E.; Nakano, J.; Turner, S.; Idrissi, H.; Schryvers, D.; Godet, S. |
Title |
Critical assessments and thermodynamic modeling of BaO-SiO2 and SiO2-TiO2 systems and their extensions into liquid immiscibility in the BaO-SiO2-TiO2 system |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Calphad computer coupling of phase diagrams and thermochemistry |
Abbreviated Journal |
Calphad |
Volume |
47 |
Issue |
|
Pages |
68-82 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
This study discusses rational reproduction of liquid immiscibility in the BaO-SiO2-TiO2 system. While a ternary assessment requires sub-binary descriptions in the same thermodynamic model, the related sub-binary systems BaO-SiO2, BaO-TiO2 and SiO2-TiO2 liquid and solid phases have been evaluated using different thermodynamic models in the literature. In this study, BaO-SiO2 and SiO2-TiO2 were assessed using the Ionic Two Sublattice model (I2SL) based on experimental data from the literature. BaO-TiO2 was already assessed using this model. Binary descriptions developed were then used for the assessment of liquid immiscibility in the BaO-SiO2-TiO2 system. Ternary interaction parameters were found necessary for rational reproduction of the new ternary experimental data gathered in the present work. The model parameters for each system were evaluated using a CAPLHAD approach. A set of parameters is proposed. They show good agreement between the calculated and experimental equilibrium liquidus, liquid immiscibility and thermochemical properties in the BaO-SiO2-TiO2 system. (C) 2014 Elsevier Ltd. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
Language |
|
Wos |
000346224700008 |
Publication Date |
2014-07-05 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0364-5916; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
1.6 |
Times cited |
9 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 1.6; 2014 IF: 1.370 |
Call Number |
UA @ lucian @ c:irua:122776 |
Serial |
540 |
Permanent link to this record |
|
|
|
Author |
Lu, J.; Martinez, G.T.; Van Aert, S.; Schryvers, D. |
Title |
Lattice deformations in quasi-dynamic strain glass visualised and quantified by aberration corrected electron microscopy |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Physica status solidi: B: basic research |
Abbreviated Journal |
Phys Status Solidi B |
Volume |
251 |
Issue |
10 |
Pages |
2034-2040 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Advanced transmission electron microscopy and statistical parameter estimated quantification procedures were applied to study the room temperature quasi-dynamical strain glass state in NiTi alloys. Nanosized strain pockets are visualised and the displacements of the atom columns are quantified. A comparison is made with conventional high-resolution transmission electron microscopy images of point defect induced strains in NiAl alloys. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Berlin |
Editor |
|
Language |
|
Wos |
000344360000009 |
Publication Date |
2014-03-31 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0370-1972; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
1.674 |
Times cited |
2 |
Open Access |
|
Notes |
Fwo |
Approved |
Most recent IF: 1.674; 2014 IF: 1.489 |
Call Number |
UA @ lucian @ c:irua:120471 |
Serial |
1801 |
Permanent link to this record |
|
|
|
Author |
Espinoza Torres, C.; Condó, A.M.; Haberkorn, N.; Zelaya, E.; Schryvers, D.; Guimpel, J.; Lovey, F.C. |
Title |
Structures in textured Cu-Al-Ni shape memory thin films grown by sputtering |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Materials characterization |
Abbreviated Journal |
Mater Charact |
Volume |
96 |
Issue |
|
Pages |
256-262 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
The structure and texture formation in CuAlNi thin films of different thicknesses (1 μm to 5 μm) grown by DC magnetron sputtering without any intentional heating of the substrate are reported. The as-grown films present grains with an average size of 20 nm. The films with thickness of 1 μm have a single metastable phase with a hexagonal structure and are textured with planes (0002) parallel to the plane of the films. It was observed that thicker films present phase coexistence between metastable hexagonal and body centered cubic structures with a gradual increment of the body centered cubic phase fraction. The films with thickness of 5 μm are textured with planes (0002) and View the MathML source101¯0 in the hexagonal structure, whereas in the body centered cubic structure the films are textured with {110} planes parallel to the plane of the films. This fact can be associated with self-heating of the substrate during the growth of the films and with the relative stability of the metastable phases. Free standing films annealed in a second step (1123 K for 1 h) present austenitic phase with L21 structure and sub-micrometric grains textured with {220}L21 planes parallel to the plane of the films. The martensitic transformation temperature was determined from the analysis of resistance against temperature measurements. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
New York |
Editor |
|
Language |
|
Wos |
000343346400032 |
Publication Date |
2014-08-10 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1044-5803; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.714 |
Times cited |
9 |
Open Access |
|
Notes |
(CONICET PIP 11220090100457) and MINCYT-FWO International Exchange Project FW/09/03 is also acknowledged |
Approved |
Most recent IF: 2.714; 2014 IF: 1.845 |
Call Number |
UA @ lucian @ c:irua:118931 |
Serial |
3321 |
Permanent link to this record |
|
|
|
Author |
Grieten, E.; Caen, J.; Schryvers, D. |
Title |
Optimal sample preparation to characterize corrosion in historical photographs with analytical TEM |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Microscopy and microanalysis |
Abbreviated Journal |
Microsc Microanal |
Volume |
20 |
Issue |
5 |
Pages |
1585-1590 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT); Antwerp Cultural Heritage Sciences (ARCHES) |
Abstract |
An alternative focused ion beam preparation method is used for sampling historical photographs containing metallic nanoparticles in a polymer matrix. We use the preparation steps of classical ultra-microtomy with an alternative final sectioning with a focused ion beam. Transmission electron microscopy techniques show that the lamella has a uniform thickness, which is an important factor for analytical transmission electron microscopy. Furthermore, the method maintains the spatial distribution of nanoparticles in the soft matrix. The results are compared with traditional preparation techniques such as ultra-microtomy and classical focused ion beam milling. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Cambridge, Mass. |
Editor |
|
Language |
|
Wos |
000345742900031 |
Publication Date |
2014-09-26 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1431-9276;1435-8115; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
1.891 |
Times cited |
|
Open Access |
|
Notes |
|
Approved |
Most recent IF: 1.891; 2014 IF: 1.877 |
Call Number |
UA @ lucian @ c:irua:118481 |
Serial |
2484 |
Permanent link to this record |
|
|
|
Author |
Shi, H.; Frenzel, J.; Martinez, G.T.; Van Rompaey, S.; Bakulin, A.; Kulkova, A.; Van Aert, S.; Schryvers, D. |
Title |
Site occupation of Nb atoms in ternary Ni-Ti-Nb shape memory alloys |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Acta materialia |
Abbreviated Journal |
Acta Mater |
Volume |
74 |
Issue |
|
Pages |
85-95 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
Nb occupancy in the austenite B2-NiTi matrix and Ti2Ni phase in NiTiNb shape memory alloys was investigated by aberration-corrected scanning transmission electron microscopy and precession electron diffraction. In both cases, Nb atoms were found to prefer to occupy the Ti rather than Ni sites. A projector augmented wave method within density functional theory was used to calculate the atomic and electronic structures of the austenitic B2-NiTi matrix phase and the Ti2Ni precipitates both with and without addition of Nb. The obtained formation energies and analysis of structural and electronic characteristics explain the preference for Ti sites for Nb over Ni sites. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
Language |
|
Wos |
000338621400009 |
Publication Date |
2014-05-08 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1359-6454; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
5.301 |
Times cited |
21 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 5.301; 2014 IF: 4.465 |
Call Number |
UA @ lucian @ c:irua:118334 |
Serial |
3028 |
Permanent link to this record |
|
|
|
Author |
Zhou, C.; Ji, G.; Chen, Z.; Wang, M.; Addad, A.; Schryvers, D.; Wang, H. |
Title |
Fabrication, interface characterization and modeling of oriented graphite flakes/Si/Al composites for thermal management applications |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Materials and design |
Abbreviated Journal |
Mater Design |
Volume |
63 |
Issue |
|
Pages |
719-728 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Highly thermally conductive graphite flakes (Gf)/Si/Al composites have been fabricated using Gf, Si powder and an AlSi7Mg0.3 alloy by an optimized pressure infiltration process for thermal management applications. In the composites, the layers of Gf were spaced apart by Si particles and oriented perpendicular to the pressing direction, which offered the opportunity to tailor the thermal conductivity (TC) and coefficient of thermal expansion (CTE) of the composites. Microstructural characterization revealed that the formation of a clean and tightly-adhered interface at the nanoscale between the side surface of the Gf and Al matrix, devoid of a detrimental Al4C3 phase and a reacted amorphous AlSiOC layer, contributed to excellent thermal performance along the alignment direction. With increasing volume fraction of Gf from 13.7 to 71.1 vol.%, the longitudinal (i.e. parallel to the graphite layers) TC of the composites increased from 179 to 526 W/m K, while the longitudinal CTE decreased from 12.1 to 7.3 ppm/K (matching the values of electronic components). Furthermore, the modified layers-in-parallel model better fitted the longitudinal TC data than the layers-in-parallel model and confirmed that the clean and tightly-adhered interface is favorable for the enhanced longitudinal TC. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Reigate |
Editor |
|
Language |
|
Wos |
000340949300086 |
Publication Date |
2014-07-17 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0261-3069; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
61 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: NA |
Call Number |
UA @ lucian @ c:irua:118124 |
Serial |
1166 |
Permanent link to this record |
|
|
|
Author |
Lu, J.; Roeffaers, M.B.J.; Bartholomeeusen, E.; Sels, B.F.; Schryvers, D. |
Title |
Intergrowth of components and ramps in coffin-shaped ZSM-5 zeolite crystals unraveled by focused ion beam-assisted transmission electron microscopy |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Microscopy and microanalysis |
Abbreviated Journal |
Microsc Microanal |
Volume |
20 |
Issue |
1 |
Pages |
42-49 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Scanning electron microscopy, focused ion beam (FIB), and transmission electron microscopy are combined to study the intergrowth of 90 degrees rotational components and of ramps in coffin-shaped ZSM-5 crystals. The 90 degrees rotational boundaries with local zig-zag features between different intergrowth components are observed in the main part of crystal. Also a new kind of displacement boundary is described. At the displacement boundary there is a shift of the unit cells along the boundary without a change in orientation. Based on lamellae prepared with FIB from different positions of the ramps and crystal, the orientation relationships between ramps and the main part of the crystal are studied and the three-dimensional morphology and growth mechanism of the ramp are illustrated. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Cambridge, Mass. |
Editor |
|
Language |
|
Wos |
000335378400006 |
Publication Date |
2013-11-05 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1431-9276;1435-8115; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
1.891 |
Times cited |
7 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 1.891; 2014 IF: 1.877 |
Call Number |
UA @ lucian @ c:irua:117688 |
Serial |
1697 |
Permanent link to this record |
|
|
|
Author |
Idrissi, H.; Kobler, A.; Amin-Ahmadi, B.; Coulombier, M.; Galceran, M.; Raskin, J.-P.; Godet, S.; Kuebel, C.; Pardoen, T.; Schryvers, D. |
Title |
Plasticity mechanisms in ultrafine grained freestanding aluminum thin films revealed by in-situ transmission electron microscopy nanomechanical testing |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Applied physics letters |
Abbreviated Journal |
Appl Phys Lett |
Volume |
104 |
Issue |
10 |
Pages |
101903 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
In-situ bright field transmission electron microscopy (TEM) nanomechanical tensile testing and in-situ automated crystallographic orientation mapping in TEM were combined to unravel the elementary mechanisms controlling the plasticity of ultrafine grained Aluminum freestanding thin films. The characterizations demonstrate that deformation proceeds with a transition from grain rotation to intragranular dislocation glide and starvation plasticity mechanism at about 1% deformation. The grain rotation is not affected by the character of the grain boundaries. No grain growth or twinning is detected. (C) 2014 AIP Publishing LLC. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
American Institute of Physics |
Place of Publication |
New York, N.Y. |
Editor |
|
Language |
|
Wos |
000333082800022 |
Publication Date |
2014-03-12 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0003-6951;1077-3118; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.411 |
Times cited |
24 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 3.411; 2014 IF: 3.302 |
Call Number |
UA @ lucian @ c:irua:116866 |
Serial |
2649 |
Permanent link to this record |
|
|
|
Author |
Li, K.; Béché, A.; Song, M.; Sha, G.; Lu, X.; Zhang, K.; Du, Y.; Ringer, S.P.; Schryvers, D. |
Title |
Atomistic structure of Cu-containing \beta" precipitates in an Al-Mg-Si-Cu alloy |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Scripta materialia |
Abbreviated Journal |
Scripta Mater |
Volume |
75 |
Issue |
|
Pages |
86-89 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
The beta '' precipitates in a peak-aged Al-Mg-Si-Cu alloy were measured with an average composition of 28.6Al-38.7Mg-26.5Si-5.17Cu (at.%) using atom probe tomography. High-angle annular dark-field observations revealed that Cu incompletely substitutes for the Mg-1 and Si-3 columns, preferentially for one column in each pair of Si-3. Cu-free Si columns form a parallelogram-shaped network that constitutes the basis of subsequent precipitates in the system, with a = 0.37 nm, b = 0.38 nm, gamma = 113 degrees and c = 0.405 nm. (C) 2013 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
Language |
|
Wos |
000331025200022 |
Publication Date |
2013-12-07 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1359-6462; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.747 |
Times cited |
22 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 3.747; 2014 IF: 3.224 |
Call Number |
UA @ lucian @ c:irua:115749 |
Serial |
201 |
Permanent link to this record |
|
|
|
Author |
Schryvers, D.; Cao, S.; Pourbabak; Shi, H.; Lu |
Title |
Recent EM investigations on nano-and micro-defect structures in SMAs |
Type |
A1 Journal article |
Year |
2013 |
Publication |
Journal of alloys and compounds |
Abbreviated Journal |
J Alloy Compd |
Volume |
577 |
Issue |
s:[1] |
Pages |
S705-S709 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
The present contribution reviews some recent electron microscopy investigations on different shape memory systems in which a variety of nano- and micro-defect structures play an essential role in the functional behaviour of the material. (NiTi3)-Ti-4 precipitates in Ni-Ti are a well-known example for which the focus is now on the 3D configurations, in Ni-Ti-Nb Nb-rich nanoprecipitates are thought to have a large impact on the hysteresis, in Co-Ni-Al an Al-enriched zone nearby the y'-precipitates yields a small sandwiched austenite while some first signs of quasidynamical lattice deformation in non-frozen Ni-Ti strain glass are measured by Cs-aberration-corrected transmission electron microscopy. (C) 2011 Elsevier B.V. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
Elsevier science sa |
Place of Publication |
Lausanne |
Editor |
|
Language |
|
Wos |
000329891400146 |
Publication Date |
2011-11-10 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0925-8388; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.133 |
Times cited |
7 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 3.133; 2013 IF: 2.726 |
Call Number |
UA @ lucian @ c:irua:114832 |
Serial |
2839 |
Permanent link to this record |
|
|
|
Author |
Cao, S.; Ke, C.B.; Zhang, X.P.; Schryvers, D. |
Title |
Morphological characterization and distribution of autocatalytic-grown Ni4Ti3 precipitates in a Ni-Ti single crystal |
Type |
A1 Journal article |
Year |
2013 |
Publication |
Journal of alloys and compounds |
Abbreviated Journal |
J Alloy Compd |
Volume |
577 |
Issue |
S:1 |
Pages |
215-218 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
The 3D size, morphology and distribution of autocatalytic-grown Ni4Ti3 precipitates in a Ni51Ti49 single crystal were characterized via a FIB/SEM Slice-and-View procedure and phase-field simulation. Important parameters on size and shape of the precipitates were measured. The pair distribution function and the minimum distance between two precipitates from different variants were calculated to describe the 3D distribution of the autocatalytic-grown Ni4Ti3 precipitates in single crystal Ni-Ti, with a comparison to the polycrystalline Ni50.8Ti49.2 alloy. Phase-field simulation was conducted to study the nucleation behavior of precipitates in the single crystal Ni-Ti. (C) 2012 Elsevier B.V. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
Language |
|
Wos |
000329891400045 |
Publication Date |
2012-02-16 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0925-8388; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.133 |
Times cited |
5 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 3.133; 2013 IF: 2.726 |
Call Number |
UA @ lucian @ c:irua:114831 |
Serial |
2203 |
Permanent link to this record |
|
|
|
Author |
Boulay, E.; Ragoen, C.; Idrissi, H.; Schryvers, D.; Godet, S. |
Title |
Influence of amorphous phase separation on the crystallization behavior of glass-ceramics in the BaO-TiO2-SiO2 system |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Journal of non-crystalline solids |
Abbreviated Journal |
J Non-Cryst Solids |
Volume |
384 |
Issue |
|
Pages |
61-72 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
The possible role of a prior amorphous phase separation on the subsequent crystallization has been the topic of vigorous debates over the last decades and has not yet been clarified, especially regarding the role of the interfaces created by the phase separation. This study proposes to focus on the interplay between a prior amorphous phase separation and the crystallization of fresnoite in the BaO-TiO2-SiO2 system. The crystallization behavior of a non-stoichiometric composition inside the miscibility gap (called APS) is compared with the stoichiometric composition (called FRES) and a non-stoichiometric composition outside the miscibility gap (called NoAPS). The crystallization mechanisms are compared using differential thermal analysis (DTA) by calculating the Avrami parameters and the activation energies as a function of the particle size. The DTA study shows that the two non-stoichiometric compositions exhibit a pronounced surface crystallization behavior whereas FRES undergoes bulk nucleation. This is supported by a multi-scale microstructure characterization. Furthermore, this study demonstrates that the amorphous phase separation and the associated interfaces do not play any significant role in the nucleation step. Moreover, transmission electron microscope (TEM) and local orientation measurements show that the growth of the dendrites is not hindered by the SiO2-rich droplets. The final stage of crystallization of APS is tentatively explained by two composition effects that must be further investigated: the viscosity effect and the formation of a eutectic. (C) 2013 Elsevier B.V. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
Language |
|
Wos |
000329422400010 |
Publication Date |
2013-07-24 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0022-3093; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.124 |
Times cited |
10 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 2.124; 2014 IF: 1.766 |
Call Number |
UA @ lucian @ c:irua:114782 |
Serial |
1614 |
Permanent link to this record |
|
|
|
Author |
Idrissi, H.; Amin-Ahmadi, B.; Wang, B.; Schryvers, D. |
Title |
Review on TEM analysis of growth twins in nanocrystalline palladium thin films : toward better understanding of twin-related mechanisms in high stacking fault energy metals |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Physica status solidi: B: basic research |
Abbreviated Journal |
Phys Status Solidi B |
Volume |
251 |
Issue |
6 |
Pages |
1111-1124 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Various modes of transmission electron microscopy including aberration corrected imaging were used in order to unravel the fundamental mechanisms controlling the formation of growth twins and the evolution of twin boundaries under mechanical and hydrogen loading modes in nanocrystalline (nc) palladium thin films. The latter were produced by electron-beam evaporation and sputter deposition and subjected to uniaxial tensile deformation as well as hydriding/dehydriding cycles. The results show that the twins form by dissociation of grain boundaries. The coherency of Σ3{111} coherent twin boundaries considerably decreases with deformation due to dislocation/twin boundary interactions while Σ3{112} incoherent twin boundaries dissociate under hydrogen cycling into two-phase boundaries bounding a new and unstable 9R phase. The effect of these elementary mechanisms on the macroscopic behavior of the palladium films is discussed and compared to recent experimental and simulation works in the literature. The results provide insightful information to guide the production of well-controlled population of growth twins in high stacking fault energy nc metallic thin films. The results also indicate directions for further enhancement of the mechanical properties of palladium films as needed for instance in palladium-based membranes in hydrogen applications. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Berlin |
Editor |
|
Language |
|
Wos |
000337608600001 |
Publication Date |
2014-02-17 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0370-1972; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
1.674 |
Times cited |
7 |
Open Access |
|
Notes |
Iap P7/21; Fwo G012012n |
Approved |
Most recent IF: 1.674; 2014 IF: 1.489 |
Call Number |
UA @ lucian @ c:irua:114580 |
Serial |
2905 |
Permanent link to this record |
|
|
|
Author |
Ji, G.; Tan, Z.; Shabadi, R.; Li, Z.; Grünewald, W.; Addad, A.; Schryvers, D.; Zhang, D. |
Title |
Triple ion beam cutting of diamond/Al composites for interface characterization |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Materials characterization |
Abbreviated Journal |
Mater Charact |
Volume |
89 |
Issue |
|
Pages |
132-137 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
A novel triple ion beam cutting technique was employed to prepare high-quality surfaces of diamond/Al composites for interfacial characterization, which has been unachievable so far. Near-perfect and artifact-free surfaces were obtained without mechanical pre-polishing. Hence, the as-prepared surfaces are readily available for further study and also, ready to be employed in a focus ion beam system for preferential selection of transmission electron microscopy samples. Dramatically different diamond/Al interface configurations – sub-micrometer Al2O3 particles and clean interfaces were unambiguously revealed. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
New York |
Editor |
|
Language |
|
Wos |
000333513400015 |
Publication Date |
2014-01-18 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1044-5803; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.714 |
Times cited |
9 |
Open Access |
|
Notes |
Fwo |
Approved |
Most recent IF: 2.714; 2014 IF: 1.845 |
Call Number |
UA @ lucian @ c:irua:113394 |
Serial |
3735 |
Permanent link to this record |
|
|
|
Author |
Gaouyat, L.; He, Z.; Colomer, J.-F.; Lambin, P.; Mirabella, F.; Schryvers, D.; Deparis, O. |
Title |
Revealing the innermost nanostructure of sputtered NiCrOx solar absorber cermets |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Solar energy materials and solar cells |
Abbreviated Journal |
Sol Energ Mat Sol C |
Volume |
122 |
Issue |
|
Pages |
303-308 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
Conversion of solar energy into thermal energy helps reducing consumption of non-renewable energies. Cermets (ceramicmetal composites) are versatile materials suitable, amongst other applications, for solar selective absorbers. Although the presence of metallic Ni particles in the dielectric matrix is a prerequisite for efficient solar selective absorption in NiCrOx cermets, no clear evidence of such particles is reported so far. By combining comprehensive chemical and structural analyses, we reveal the presumed nanostructure which is at the origin of the remarkable optical properties of this cermet material. Using sputtered NiCrOx layers in a solar absorber multilayer stack on aluminium substrate allows us to achieve solar absorptance as high as α=96.1% while keeping thermal emissivity as low as ε=2.2%, both values being comparable to best values recorded so far. With the nanostructure of sputtered NiCrOx cermets eventually revealed, further optimization of solar absorbers can be anticipated and technological exploitation of cermet materials in other applications can be foreseen. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
Language |
|
Wos |
000331494200040 |
Publication Date |
2013-11-12 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0927-0248; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
4.784 |
Times cited |
12 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 4.784; 2014 IF: 5.337 |
Call Number |
UA @ lucian @ c:irua:113086 |
Serial |
2902 |
Permanent link to this record |
|
|
|
Author |
Peirs, J.; Verleysen, P.; Tirry, W.; Rabet, L.; Schryvers, D.; Degrieck, J. |
Title |
Dynamic shear localization in Ti6Al4V |
Type |
P1 Proceeding |
Year |
2011 |
Publication |
Procedia Engineering
T2 – 11th International Conference on the Mechanical Behavior of Materials, (ICM), 2011, Como, ITALY (ICM11) |
Abbreviated Journal |
|
Volume |
|
Issue |
|
Pages |
1-6 |
Keywords |
P1 Proceeding; Electron microscopy for materials research (EMAT) |
Abstract |
The alloy Ti6Al4V is known to be prone to the formation of adiabatic shear bands when dynamically loaded in shear. This causes a catastrophic decrease of the load carrying capacity and is usually followed by fracture. Although, the main mechanism is recognized to be the competition between strain hardening and thermal softening, a detailed understanding of the role of microstructural plasticity mechanisms and macroscopic loading conditions does not exist yet. To study strain localization and shear fracture, different high strain rate shear tests have been carried out: compression of hat-shaped specimens, torsion of thin walled tubular specimens and in-plane shear tests. The value of the three techniques in studying shear localization is evaluated. Post-mortem analysis of the fracture surface and the materials' microstructure is performed with optical and electron microscopy. In all cases a ductile fracture is observed. SEM and TEM techniques are used to study the local microstructure and composition in the shear band and as such the driving mechanism for the ASB formation. (C) 2011 Published by Elsevier Ltd. Selection and/or peer-review under responsibility of ICM11 |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000300451302060 |
Publication Date |
2011-06-20 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
Series Volume |
10 |
Series Issue |
|
Edition |
|
ISSN |
1877-7058; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
4 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: NA |
Call Number |
UA @ lucian @ c:irua:113069 |
Serial |
767 |
Permanent link to this record |