|
“Effect of high temperature deposition on CoSi2 phase formation”. Comrie CM, Ahmed A, Smeets D, Demeulemeester J, Turner S, Van Tendeloo G, Detavernier C, Vantomme A, Journal of applied physics 113, 234902 (2013). http://doi.org/10.1063/1.4811352
Abstract: This paper discusses the nucleation behaviour of the CoSi to CoSi2 transformation from cobalt silicide thin films grown by deposition at elevated substrate temperatures ranging from 375 °C to 600 °C. A combination of channelling, real-time Rutherford backscattering spectrometry, real-time x-ray diffraction, and transmission electron microscopy was used to investigate the effect of the deposition temperature on the subsequent formation temperature of CoSi2, its growth behaviour, and the epitaxial quality of the CoSi2 thus formed. The temperature at which deposition took place was observed to exert a significant and systematic influence on both the formation temperature of CoSi2 and its growth mechanism. CoSi films grown at the lowest temperatures were found to increase the CoSi2 nucleation temperature above that of CoSi2 grown by conventional solid phase reaction, whereas the higher deposition temperatures reduced the nucleation temperature significantly. In addition, a systematic change in growth mechanism of the subsequent CoSi2 growth occurs as a function of deposition temperature. First, the CoSi2 growth rate from films grown at the lower reactive deposition temperatures is substantially lower than that grown at higher reactive deposition temperatures, even though the onset of growth occurs at a higher temperature, Second, for deposition temperatures below 450 °C, the growth appears columnar, indicating nucleation controlled growth. Elevated deposition temperatures, on the other hand, render the CoSi2 formation process layer-by-layer which indicates enhanced nucleation of the CoSi2 and diffusion controlled growth. Our results further indicate that this observed trend is most likely related to stress and changes in microstructure introduced during reactive deposition of the CoSi film. The deposition temperature therefore provides a handle to tune the CoSi2 growth mechanism.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.068
Times cited: 2
DOI: 10.1063/1.4811352
|
|
|
“Analyzing a self-managed CHP system for greenhouse cultivation as a profitable way to reduce CO2-emissions”. Compernolle T, Witters N, Van Passel S, Thewys T, Energy 36, 1940 (2011). http://doi.org/10.1016/J.ENERGY.2010.02.045
Abstract: To counter global warming, a transition to a low-carbon economy is needed. The greenhouse sector can contribute by installing Combined Heat and Power (CHP) systems, known for their excellent energy efficiency. Due to the recent European liberalization of the energy market, glass horticulturists have the opportunity to sell excess electricity to the market and by tailored policy and support measures, regional governments can fill the lack of technical and economic knowledge, causing initial resistance. This research investigates the economic and environmental opportunities using two detailed cases applying a self managed cogeneration system. The Net Present Value is calculated to investigate the economic feasibility. The Primary Energy Saving, the CO2 Emission Reduction indicator and an Emission Balance are applied to quantify the environmental impact. The results demonstrate that a self-managed CHP system is economic viable and that CO2 emissions are reduced. (C) 2010 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology
Impact Factor: 4.52
Times cited: 19
DOI: 10.1016/J.ENERGY.2010.02.045
|
|
|
“Groundwater remediation and the cost effectiveness of phytoremediation”. Compernolle T, Van Passel S, Weyens N, Vangronsveld J, Lebbe L, Thewys T, International Journal Of Phytoremediation 14, 861 (2012). http://doi.org/10.1080/15226514.2011.628879
Abstract: In 1999, phytoremediation was applied at the site of a Belgian car factory to contain two BTEX plumes. This case study evaluates the cost effectiveness of phytoremediation compared to other remediation options, applying a tailored approach for economic evaluation. Generally, when phytoremediation is addressed as being cost effective, the cost effectiveness is only determined on an average basis. This study however, demonstrates that an incremental analysis may provide a more nuanced conclusion. When the cost effectiveness is calculated on an average basis, in this particular case, the no containment strategy (natural attenuation) has the lowest cost per unit mass removed and hence, should be preferred. However, when the cost effectiveness is determined incrementally, no containment should only be preferred if the value of removing an extra gram of contaminant mass is lower than 320. Otherwise, a permeable reactive barrier should be adopted. A similar analysis is provided for the effect determined on the basis of remediation time. Phytoremediation is preferred compared to no containment if reaching the objective one year earlier is worth 7 000.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
Impact Factor: 1.77
Times cited: 12
DOI: 10.1080/15226514.2011.628879
|
|
|
“Populieren en hun bacteriën : een sanering hoeft niet altijd duur en ingrijpend te zijn”. Compernolle T, Van Passel S, Lebbe L, Vangronsveld J, Thewys T, Nieuwsbrief milieu &, economie 24, 15 (2010)
Keywords: A3 Journal article; Economics
|
|
|
“The value of groundwater modeling to support a pump and treat design”. Compernolle T, Van Passel S, Lebbe L, Groundwater monitoring &, remediation 33, 111 (2013). http://doi.org/10.1111/GWMR.12018
Abstract: A wide range of rules, algorithms, and models are available to design an effective pump and treat remediation system. Often, one refers to the effectiveness of the developed pump and treat system to demonstrate how valuable the use of a groundwater model can be. An economic valuation of the groundwater model is usually missing. This study provides a framework that puts the discussion concerning the use of groundwater models in an economic perspective. It is not only demonstrated that a more effective pump and treat system can be designed using a groundwater model, but also the economic implications of using a groundwater model are calculated. A set of economic decision rules is applied to determine the economic value of a groundwater model. It is shown that investing in a groundwater model can be economically worthwhile. The remediation time is reduced, remediation costs are saved and the property can be sold more early. These benefits outweigh the costs of developing a groundwater model, and hence a positive net benefit (NB) is determined.
Keywords: A1 Journal article; Economics
DOI: 10.1111/GWMR.12018
|
|
|
“Bioremediation : how to deal with removal efficiency uncertainty? An economic application”. Compernolle T, Van Passel S, Lebbe L, Journal Of Environmental Management 127, 77 (2013). http://doi.org/10.1016/J.JENVMAN.2013.04.016
Abstract: Bioremediation is a remediation strategy, which has considerable strength but also certain limitations. Complex and uncertain relationships among biomass, contaminants, and nutrients lead to an uncertain level of removal efficiency. The uncertainty inherent to a bioremediation strategy should be addressed in the remediation selection process. In order to evaluate the bioremediation strategy economically, this study takes into account the reversibility of a decision. A decision tree structures the different remediation strategies, thus giving the possible courses of action open to the decision maker. The option value indicates the importance of having the possibility to reverse a previously made decision. Compared with conventional economic evaluation tools, more information to ground the selection made is revealed.
Keywords: A1 Journal article; Economics
Impact Factor: 4.01
Times cited: 1
DOI: 10.1016/J.JENVMAN.2013.04.016
|
|
|
“The option to abandon : stimulating innovative groundwater remediation technologies characterized by technological uncertainty”. Compernolle T, Van Passel S, Huisman K, Kort P, Science Of The Total Environment 496, 63 (2014). http://doi.org/10.1016/J.SCITOTENV.2014.07.019
Abstract: Many studies on technology adoption demonstrate that uncertainty leads to a postponement of investments by integrating a wait option in the economic analysis. The aim of this study however is to demonstrate how the investment in new technologies can be stimulated by integrating an option to abandon. Furthermore, this real option analysis not only considers the ex ante decision analysis of the investment in a new technology under uncertainty, but also allows for an ex post evaluation of the investment. Based on a case study regarding the adoption of an innovative groundwater remediation strategy, it is demonstrated that when the option to abandon the innovative technology is taken into account, the decision maker decides to invest in this technology, while at the same time it determines an optimal timing to abandon the technology if its operation proves to be inefficient. To reduce uncertainty about the effectiveness of groundwater remediation technologies, samples are taken. Our analysis shows that when the initial belief in an effective innovative technology is low, it is important that these samples provide correct information in order to justify the adoption of the innovative technology. (C) 2014 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Economics
Impact Factor: 4.9
Times cited: 4
DOI: 10.1016/J.SCITOTENV.2014.07.019
|
|
|
“Conductance of a copper-nanotube bundle interface: impact of interface geometry and wave-function interference”. Compemolle S, Pourtois G, Sorée B, Magnus W, Chibotaru LF, Ceulemans A, Physical review : B : condensed matter and materials physics 77, 193406 (2008). http://doi.org/10.1103/PhysRevB.77.193406
Keywords: A1 Journal article; Condensed Matter Theory (CMT); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 3.836
Times cited: 8
DOI: 10.1103/PhysRevB.77.193406
|
|
|
“Large-scale synthesis of single-wall carbon nanotubes by catalytic chemical vapor deposition (CCVD) method”. Colomer JF, Stephan C, Lefrant S, Van Tendeloo G, Willems I, Konya Z, Fonseca A, Laurent C, Nagy JB, Chemical physics letters 317, 83 (2000). http://doi.org/10.1016/S0009-2614(99)01338-X
Abstract: The large-scale production of single-wall carbon nanotubes (SWNTs) is reported. Large quantities of SWNTs can be synthesised by catalytic decomposition of methane over well-dispersed metal particles supported on MgO at 1000 degrees C. The thus produced SWNTs can be separated easily from the support by a simple acidic treatment to obtain a product with high yields (70-80%) of SWNTs. Because the typical synthesis time is 10 min, 1 g of SWNTs can be synthesised per day by this method. The SWNTs are characterized by high-resolution transmission electron microscopy and by Raman spectroscopy, showing the quality and the quantity of products. (C) 2000 Elsevier Science B.V. All rights reserved.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.815
Times cited: 344
DOI: 10.1016/S0009-2614(99)01338-X
|
|
|
“Electron diffraction and microscopy of single-walled carbon nanotube bundles”. Colomer J-F, Van Tendeloo G Kluwer, Boston, Mass., page 45 (2003).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
|
|
|
“Purification of catalytically produced multi-wall nanotubes”. Colomer J-F, Piedigrosso P, Willems I, Journet C, Bernier P, Van Tendeloo G, Fonseca A, Nagy JB, Journal of the Chemical Society : Faraday transactions: physical chemistry and chemical physics 94, 3753 (1998). http://doi.org/10.1039/a806804f
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 92
DOI: 10.1039/a806804f
|
|
|
“Microwave-assisted bromination of double-walled carbon nanotubes”. Colomer J-F, Marega R, Traboulsi H, Meneghetti M, Van Tendeloo G, Bonifazi D, Chemistry of materials 21, 4747 (2009). http://doi.org/10.1021/cm902029m
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 9.466
Times cited: 46
DOI: 10.1021/cm902029m
|
|
|
“Study of the packing of double-walled carbon nanotubes into bundles by transmission electron microscopy and electron diffraction”. Colomer J-F, Henrard L, Van Tendeloo G, Lucas A, Lambin P, Journal of materials chemistry 14, 603 (2004). http://doi.org/10.1039/b311551h
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 27
DOI: 10.1039/b311551h
|
|
|
“Bundles of identical double-walled carbon nanotubes”. Colomer J-F, Henrard L, Launois P, Van Tendeloo G, Lucas AA, Lambin P, Chemical communications , 2592 (2004). http://doi.org/10.1039/b410930a
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 6.319
Times cited: 13
DOI: 10.1039/b410930a
|
|
|
“Interpretation of electron diffraction from carbon nanotube bundles presenting precise helicity”. Colomer J-F, Henrard L, Launois P, Van Tendeloo G, Lucas AA, Lambin P, Physical review : B : condensed matter and materials physics 70, 075408 (2004). http://doi.org/10.1103/PhysRevB.70.075408
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.836
Times cited: 19
DOI: 10.1103/PhysRevB.70.075408
|
|
|
“Electron diffraction and microscopy of single-wall carbon nanotube bundles produced by different methods”. Colomer J-F, Henrard L, Lambin P, Van Tendeloo G, European physical journal : B : condensed matter and complex systems 27, 111 (2002). http://doi.org/10.1140/epjb/e20020135
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.461
Times cited: 43
DOI: 10.1140/epjb/e20020135
|
|
|
“Electron diffraction of nanotubes bundles : unique helicity and tube-tube atomically coherent packing”. Colomer J-F, Henrard L, Lambin P, Van Tendeloo G, AIP conference proceedings
T2 –, 16th International Winterschool on Electronic Properties of Novel, Materials, MAR 02-09, 2002, KIRCHBERG, AUSTRIA , 314 (2002). http://doi.org/10.1063/1.1514131
Abstract: The atomic structure of single-wall carbon nanotube bundles produced by three different techniques has been characterized by electron diffraction and microscopy. Small bundles produced by Catalytical Chemical Vapor Deposition (CCVD) exhibit only one or two tube chiralities within a single bundle while bundles produced by arc-discharge or laser-ablation exhibit more chiralities. A detailed analysis of the central line of diffraction is also presented. The CCVD nanotubes present more intense spots around 1.7 Angstrom(-1) < k < 2Angstrom(-1) (k is the momentum transfer) compared to what is observed for nanotubes produced by other methods. Amongst the possible explanation for such an anomaly, we put forward that in this range of momentum transfer, the relative tube orientations and translations are important for what concerns the interpretation of the diffraction peaks intensities.
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
DOI: 10.1063/1.1514131
|
|
|
“Electron diffraction study of small bundles of single-wall carbon nanotubes with unique helicity”. Colomer J-F, Henrard L, Lambin P, Van Tendeloo G, Physical review : B : condensed matter and materials physics 64, 125425 (2001). http://doi.org/10.1103/PhysRevB.64.125425
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 3.836
Times cited: 31
DOI: 10.1103/PhysRevB.64.125425
|
|
|
“Rings of double-walled carbon nanotube bundles”. Colomer J-F, Henrard L, Flahaut E, Van Tendeloo G, Lucas AA, Lambin P, Nano letters 3, 685 (2003). http://doi.org/10.1021/nl034159w
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 12.712
Times cited: 59
DOI: 10.1021/nl034159w
|
|
|
“Synthesis of single wall carbon nanotubes by catalytic decomposition of hydrocarbons”. Colomer J-F, Bister G, Willems I, Konya Z, Fonseca A, Van Tendeloo G, Nagy JB, Chemical communications , 1343 (1999). http://doi.org/10.1039/a903142a
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 6.319
Times cited: 110
DOI: 10.1039/a903142a
|
|
|
“Characterization of single-wall carbon nanotubes produced by CCVD method”. Colomer J-F, Benoit J-M, Stephan C, Lefrant S, Van Tendeloo G, Nagy JB, Chemical physics letters 345, 11 (2001). http://doi.org/10.1016/S0009-2614(01)00841-7
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.815
Times cited: 45
DOI: 10.1016/S0009-2614(01)00841-7
|
|
|
“Aluminum incorporation into MCM-48 toward the creation of Brønsted acidity”. Collart O, Cool P, van der Voort P, Meynen V, Vansant EF, Houthoofd KJ, Grobet PJ, Lebedev OI, Van Tendeloo G, The journal of physical chemistry : B : condensed matter, materials, surfaces, interfaces and biophysical 108, 13905 (2004). http://doi.org/10.1021/jp049837x
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT); Laboratory of adsorption and catalysis (LADCA)
Impact Factor: 3.177
Times cited: 13
DOI: 10.1021/jp049837x
|
|
|
“High strength-ductility of thin nanocrystalline palladium films with nanoscale twins : on-chip testing and grain aggregate model”. Colla M-S, Wang B, Idrissi H, Schryvers D, Raskin J-P, Pardoen T, Acta materialia 60, 1795 (2012). http://doi.org/10.1016/j.actamat.2011.11.054
Abstract: The mechanical behaviour of thin nanocrystalline palladium films with an ∼30 nm in plane grain size has been characterized on chip under uniaxial tension. The films exhibit a large strain hardening capacity and a significant increase in the strength with decreasing thickness. Transmission electron microscopy has revealed the presence of a moderate density of growth nanotwins interacting with dislocations. A semi-analytical grain aggregate model is proposed to investigate the impact of different contributions to the flow behaviour, involving the effect of twins, of grain size and of the presence of a thin surface layer. This model provides guidelines to optimizing the strength/ductility ratio of the films.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 5.301
Times cited: 38
DOI: 10.1016/j.actamat.2011.11.054
|
|
|
“Dislocation-mediated relaxation in nanograined columnar palladium films revealed by on-chip time-resolved HRTEM testing”. Colla M-S, Amin-Ahmadi B, Idrissi H, Malet L, Godet S, Raskin J-P, Schryvers D, Pardoen T, Nature communications 6, 5922 (2015). http://doi.org/10.1038/ncomms6922
Abstract: The high-rate sensitivity of nanostructured metallic materials demonstrated in the recent literature is related to the predominance of thermally activated deformation mechanisms favoured by a large density of internal interfaces. Here we report time-resolved high-resolution electron transmission microscopy creep tests on thin nanograined films using on-chip nanomechanical testing. Tests are performed on palladium, which exhibited unexpectedly large creep rates at room temperature. Despite the small 30-nm grain size, relaxation is found to be mediated by dislocation mechanisms. The dislocations interact with the growth nanotwins present in the grains, leading to a loss of coherency of twin boundaries. The density of stored dislocations first increases with applied deformation, and then decreases with time to drive additional deformation while no grain boundary mechanism is observed. This fast relaxation constitutes a key issue in the development of various micro- and nanotechnologies such as palladium membranes for hydrogen applications.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 12.124
Times cited: 34
DOI: 10.1038/ncomms6922
|
|
|
“Intergranular fracture in irradiated Inconel X-750 containing very high concentrations of helium and hydrogen”. Colin D Judge Nicolas Gauquelin Lori Walters Mike Wright James I Cole James Madden Gianluigi A Botton Malcolm Griffiths, Journal of Nuclear Materials 457, 165 (2015). http://doi.org/10.1016/j.jnucmat.2014.10.008
Abstract: In recent years, it has been observed that Inconel X-750 spacers in CANDU reactors exhibits lower ductility with reduced load carrying capacity following irradiation in a reactor environment. The fracture behaviour of ex-service material was also found to be entirely intergranular at high doses. The thermalized flux spectrum in a CANDU reactor leads to transmutation of 58Ni to 59Ni. The 59Ni itself has unusually high thermal neutron reaction cross-sections of the type: (n, γ), (n, p), and (n, α). The latter two reactions, in particular, contribute to a significant enhancement of the atomic displacements in addition to creating high concentrations of hydrogen and helium within the material. Microstructural examinations by transmission electron microscopy (TEM) have confirmed the presence of helium bubbles in the matrix and aligned along grain boundaries and matrix–precipitate interfaces. Helium bubble size and density are found to be highly dependent on the irradiation temperature and material microstructure; the bubbles are larger within grain boundary precipitates. TEM specimens extracted from fracture surfaces and crack tips provide information that is consistent with crack propagation along grain boundaries due to the presence of He bubbles.
Keywords: A1 Journal Article; Electron Microscopy for Materials Science (EMAT) ;
Times cited: 29
DOI: 10.1016/j.jnucmat.2014.10.008
|
|
|
“Collective cyclotron modes in high mobility two-dimensional hole systems in GaAs-(Ga,Al)As heterojunctions: 1: experiments at low magnetic fields and theory”. Cole BE, Peeters FM, Ardavan A, Hill SO, Singleton J, Batty W, Chamberlain JM, Polisskii A, Henini M, Cheng T, Journal of physics : condensed matter 9, 3163 (1997)
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.649
Times cited: 20
|
|
|
“Collective cyclotron modes in high mobility two-dimensional hole systems in GaAs-(Ga,Al)As heterojunctions: 2: experiments at magnetic fields of up to forty Tesla”. Cole BE, Batty W, Singleton J, Chamberlain JM, Li L, van Bockstal L, Imanaka Y, Shimamoto Y, Miura N, Peeters FM, Henini M, Cheng T, Journal of physics : condensed matter 9, 4887 (1997)
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.649
Times cited: 5
|
|
|
“Importance of twinning in static and dynamic compression of a Ti-6Al-4V titanium alloy with an equiaxed microstructure”. Coghe F, Tirry W, Rabet L, Schryvers D, Van Houtte P, Materials science and engineering: part A: structural materials: properties, microstructure and processing 537, 1 (2012). http://doi.org/10.1016/j.msea.2011.12.047
Abstract: Whereas deformation twinning is known to be an important deformation mechanism for hexagonal materials like magnesium and pure titanium, so far almost no literature exists on the twinning behaviour of the Ti-6Al-4V alloy. In this work it was shown that the activation of twinning as a deformation mechanism could have a pronounced effect on the mechanical behaviour of the Ti-6Al-4V alloy. This effect is even more pronounced under dynamic loading conditions. Transmission electron microscopy showed that only the {1 0 1 2}{1 0 1 1} tensile twin system was activated under certain loading conditions. Light-optical microscopy and electron backscatter diffraction data were afterwards used to experimentally determine the twin fractions. The importance of twinning for the texture evolution was also studied. It was shown that even small twin fractions can lead to distinct texture features, especially due to the discrete reorientation of the c-axes. The experimental results were compared to simulated results that were obtained with a viscoplastic self-consistent crystal plasticity code, after experimental validation that twinning can be reliably modelled as a unidirectional slip system. Although good agreement was obtained for the experimental and simulated stress-strain curves, the simulated results concerning twinning correlated well only on a qualitative basis as the simulated twin fractions were systematically higher than the experimental fractions. This seems to strengthen the hypothesis made by other research groups that complete grains might reorient by twinning. (C) 2011 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 3.094
Times cited: 35
DOI: 10.1016/j.msea.2011.12.047
|
|
|
“Gold and silver-catalyzed reductive amination of aromatic carboxylic acids to benzylic amines”. Coeck R, Meeprasert J, Li G, Altantzis T, Bals S, Pidko EA, De Vos DE, Acs Catalysis 11, 7672 (2021). http://doi.org/10.1021/ACSCATAL.1C01693
Abstract: The reductive amination of benzoic acid and its derivatives would be an effective addition to current synthesis methods for benzylamine. However, with current technology it is very difficult to keep the aromaticity intact when starting from benzoic acid, and salt wastes are often generated in the process. Here, we report a heterogeneous catalytic system for such a reductive amination, requiring solely H-2 and NH3 as the reactants. The Ag/TiO2 or Au/TiO2 catalysts can be used multiple times, and very little noble metal is required, only 0.025 mol % Au. The catalysts are bifunctional: the support catalyzes the dehydration of both the ammonium carboxylate to the amide and of the amide to the nitrile, while the sites at the metal-support interface promote the hydrogenation of the in situ generated nitrile. Yields of up to 92% benzylamine were obtained.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Applied Electrochemistry & Catalysis (ELCAT)
Impact Factor: 10.614
Times cited: 16
DOI: 10.1021/ACSCATAL.1C01693
|
|
|
“Investigation by electron diffraction microscopy of (RE)BaCuOS polycrystalline ceramic compounds: interpretation of unexpected superstructures and influence of secondary phases”. Cloots R, Rulmont A, Krekels T, Van Tendeloo G, Diko P, Ausloos M, Journal of crystal growth 129, 394 (1993)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.698
Times cited: 5
|
|