|
“Size-controlled electrodeposition of Cu nanoparticles on gas diffusion electrodes in methanesulfonic acid solution”. Pacquets L, Irtem E, Neukermans S, Daems N, Bals S, Breugelmans T, Journal Of Applied Electrochemistry 51 (2020). http://doi.org/10.1007/S10800-020-01474-5
Abstract: In this paper electrodeposition is used to obtain Cu nanoparticles, as it allows good control over particle size and distribution. These Cu particles were deposited onto a gas diffusion electrode which increased the resulting surface area. Prior to deposition, the surface was pre-treated with NaOH, HNO3, MQ and TX100 to investigate the influence on the electrodeposition of Cu on the gas diffusion electrode (GDE). When using HNO3, the smallest particles with the most homogeneous distribution and high particle roughness were obtained. Once the optimal substrate was determined, we further demonstrated that by altering the electrodeposition parameters, the particle size and density could be tuned. On the one hand, increasing the nucleation potential led to a higher particle density resulting in smaller particles because of an increased competition between particles. Finally, the Cu particle size increased when applying a greater growth charge and growth potential. This fundamental study thus opens up a path towards the synthesis of supported Cu materials with increased surface areas, which is interesting from a catalytic point of view. Larger surface areas are generally correlated with a better catalyst performance and thus higher product yields. This research can contributed in obtaining new insides into the deposition of metallic nanoparticles on rough surfaces. [GRAPHICS] .
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Applied Electrochemistry & Catalysis (ELCAT)
Impact Factor: 2.9
Times cited: 3
DOI: 10.1007/S10800-020-01474-5
|
|
|
“Modeling of the performance of BSCF capillary membranes in four-end and three-end integration mode”. Buysse C, Michielsen B, Middelkoop V, Snijkers F, Buekenhondt A, Kretzschmar J, Lenaerts S, Ceramics international 39, 4113 (2013). http://doi.org/10.1016/J.CERAMINT.2012.10.266
Abstract: Owing to their high surface-to-volume ratio, there has been an increasing research interest in mixed ionic electronic conducting (MIEC) capillary membranes for large-scale high temperature oxygen separation applications. They offer an energy-efficient solution for high temperature combustion processes in oxy-fuel and pre-combustion CO2 capture technologies used in fossil fuel power plants. In order to assess the effectiveness of these membranes in power plant applications, the impact of the geometry of Ba0.5Sr0.5Co0.8Fe0.2O3-delta (BSCF) capillaries on their performance in the three-end and four-end integration modes has been investigated and thoroughly discussed. The model's parameters were derived from four-end mode lab-scale experiments using gas-tight, macrovoid free and sulfur-free BSCF capillary membranes that were prepared by a phase-inversion spinning technique. The results of this modeling study revealed that in the four-end mode higher average oxygen fluxes and smaller total membrane areas can be obtained than in the three-end mode. This is due to the higher pO(2) gradient across the membrane wall. (C) 2012 Elsevier Ltd and Techna Group S.r.l. All rights reserved.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 2.986
Times cited: 4
DOI: 10.1016/J.CERAMINT.2012.10.266
|
|
|
“Hydrothermal synthesis of carbonate-free submicron-sized barium titanate from an amorphous precursor : synthesis and characterization”. Özen M, Mertens M, Luyten J, Snijkers F, d' Hondt H, Cool P, Ceramics international 38, 619 (2012). http://doi.org/10.1016/j.ceramint.2011.07.051
Abstract: In this paper, the amorphous barium titanate precursor was prepared by the peroxo-hydroxide method and post-treated by various drying procedures, such as: room temperature drying, room temperature vacuum drying and vacuum drying at 50 degrees C. The objective in the latter two treatments was to increase the Ti-O-Ba bonds of the precursor. The post-treated precursors were compared with the untreated (i.e., 'wet') precursor. Also, a barium titanate precursor was prepared by an alkoxide route. Afterwards, the precursors were hydrothermally treated at 200 degrees C in a 10 M NaOH solution. Vacuum drying of the precursor seemingly promoted the formation of Ti-O-Ti bonds in the hydrothermal end-product. The low Ba:Ti ratio (0.66) of the alkoxide-route prepared precursor lead to a multi-phase hydrothermal product with BaTiO(3) as the main phase. In contrast, phase pure BaTiO(3), i.e. without BaCO(3) contamination, was obtained for the precursor which was dried at room temperature. Cube-shaped and highly crystalline BaTiO(3) particles were observed by electron microscopy for the hydrothermally treated peroxo-hydroxide-route prepared precursor. (C) 2011 Elsevier Ltd and Techna Group S.r.l. All rights reserved.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT); Laboratory of adsorption and catalysis (LADCA)
Impact Factor: 2.986
Times cited: 14
DOI: 10.1016/j.ceramint.2011.07.051
|
|
|
“Texturing of hydrothermally synthesized BaTiO3 in a strong magnetic field by slip casting”. Özen M, Mertens M, Snijkers F, Van Tendeloo G, Cool P, Ceramics international 42, 5382 (2016). http://doi.org/10.1016/j.ceramint.2015.12.073
Abstract: Barium titanate powder was processed by slip casting in a rotating strong magnetic field of 9.4 T. The orientation factor of the sintered compact was analyzed by the X-ray diffraction technique and the microstructure (grain-size) was analyzed by scanning electron microscope. The hydrothermally prepared barium titanate was used as matrix material and the molten-salt synthesized barium titanate, with a larger particle-size, was used as template for the templated grain-growth process. Addition of large template particles was observed to increase the orientation factor of the sintered cast (5 vol% loading). Template particles acted as starting grains for the abnormal grain-growth process and the average grain-size was increased after sintering. Increasing the solid loading (15 vol%) resulted in a similar orientation factor with a decrease of the average grain size by more than half. However, addition of templates to the 15 vol% cast had a negative effect on the orientation factor. The impingement of growing particles was stated as the primary cause of particle misorientation resulting in a low orientation factor after sintering. Different heating conditions were tested and it was determined that a slow heating rate gave the highest orientation factor, the smallest average grain-size and the highest relative density. (C) 2015 Elsevier Ltd and Techna Group S.r.l. All rights reserved.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT); Laboratory of adsorption and catalysis (LADCA)
Impact Factor: 2.986
Times cited: 11
DOI: 10.1016/j.ceramint.2015.12.073
|
|
|
“Novel poly(butylene succinate) nanocomposites containing strontium hydroxyapatite nanorods with enhanced osteoconductivity for tissue engineering applications”. Nerantzaki M, Filippousi M, Van Tendeloo G, Terzopoulou Z, Bikiaris D, Goudouri OM, Detsch R, Grueenewald A, Boccaccini AR, Express polymer letters 9, 773 (2015). http://doi.org/10.3144/expresspolymlett.2015.73
Abstract: Three series of poly(butylene succinate) (PBSu) nanocomposites containing 0.5, 1 and 2.5 wt% strontium hydroxyapatite [Sr-5(PO4)(3)OH] nanorods (SrHAp nrds) were prepared by in situ polymerisation. The structural effects of Sr-5(PO4)(3)OH nanorods, for the different concentrations, inside the polymeric matrix (PBSu), were studied through high angle annular dark field scanning transmission electron microscopy (HAADF-STEM). HAADF-STEM measurements revealed that the SrHAp nanorods at low concentrations are dispersed inside the polymeric PBSu matrix while in 1 wt% some aggregates are formed. These aggregations affect the mechanical properties giving an enhancement for the concentration of 0.5 wt% SrHAp nrds in tensile strength, while a reduction is recorded for higher loadings of the nanofiller. Studies on enzymatic hydrolysis revealed that all nanocomposites present higher hydrolysis rates than neat PBSu, indicating that nanorods accelerate the hydrolysis degradation process. In vitro bioactivity tests prove that SrHAp nrds promote the formation of hydroxyapatite on the PBSu surface. All nanocomposites were tested also in relevant cell culture using osteoblast-like cells (MG-63) to demonstrate their biocompatibility showing SrHAp nanorods support cell attachment.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.983
Times cited: 21
DOI: 10.3144/expresspolymlett.2015.73
|
|
|
“Single-layer and bilayer graphene superlattices: collimation, additional Dirac points and Dirac lines”. Barbier M, Vasilopoulos P, Peeters FM, Philosophical transactions of the Royal Society : mathematical, physical and engineering sciences 368, 5499 (2010). http://doi.org/10.1098/rsta.2010.0218
Abstract: We review the energy spectrum and transport properties of several types of one-dimensional superlattices (SLs) on single-layer and bilayer graphene. In single-layer graphene, for certain SL parameters an electron beam incident on an SL is highly collimated. On the other hand, there are extra Dirac points generated for other SL parameters. Using rectangular barriers allows us to find analytical expressions for the location of new Dirac points in the spectrum and for the renormalization of the electron velocities. The influence of these extra Dirac points on the conductivity is investigated. In the limit of δ-function barriers, the transmission T through and conductance G of a finite number of barriers as well as the energy spectra of SLs are periodic functions of the dimensionless strength P of the barriers, Graphic, with vF the Fermi velocity. For a KronigPenney SL with alternating sign of the height of the barriers, the Dirac point becomes a Dirac line for P = π/2+nπ with n an integer. In bilayer graphene, with an appropriate bias applied to the barriers and wells, we show that several new types of SLs are produced and two of them are similar to type I and type II semiconductor SLs. Similar to single-layer graphene SLs, extra Dirac points are found in bilayer graphene SLs. Non-ballistic transport is also considered.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.97
Times cited: 64
DOI: 10.1098/rsta.2010.0218
|
|
|
“Raman study of different crystalline forms of PbCrO4 and PbCr1-xSxO4 solid solutions for the noninvasive identification of chrome yellows in paintings : a focus on works by Vincent van Gogh”. Monico L, Janssens K, Hendriks E, Brunetti BG, Miliani C, Journal of Raman spectroscopy 45, 1034 (2014). http://doi.org/10.1002/JRS.4548
Abstract: Chrome yellows, a class of pigments frequently used by painters of the Impressionism and Post-impressionism period, are known for their different chemical stability; the latter depends on the chemical composition (PbCrO4, PbCr1-xSxO4) and crystalline structure (monoclinic or orthorhombic) of the material. The possibility to distinguish among different forms of this pigment is therefore relevant in order to extend knowledge on the corresponding degradation process that is observed on several original paintings. For this purpose, three paintings conserved at the Van Gogh Museum (Amsterdam) were analyzed using noninvasive Raman spectroscopy, while equivalent investigations employing bench-top instrumentation were performed to obtain information from micro-samples originating from these works of art. In each painting, the chrome yellow was identified either as monoclinic PbCrO4 or in the form of monoclinic PbCr1-xSxO4 (x<0.25) or S-rich orthorhombic PbCr1-xSxO4 (x similar to 0.5). Our ability to make this fairly subtle distinction is based on a Raman study of several oil paint model samples made up of monoclinic and/or orthorhombic crystalline forms of PbCrO4 and PbCr1-xSxO4 (0.1x0.8). These paints were studied using several excitation wavelengths (namely 785.0, 532.0, 514.5, and 488nm). Because of the absence of the resonance Raman effect, which strongly enhances the chromate symmetric stretching band, and the absence of any laser-induced photodecomposition, it is advantageous to acquire data at 785.0nm. The band-shape and the position of the chromate bending modes proved to be more sensitive to the solid solution composition and crystalline structure than the stretching modes and can be used as distinctive spectral markers to discriminate among the different chrome yellow forms that are present. Copyright (c) 2014 John Wiley & Sons, Ltd.
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Impact Factor: 2.969
Times cited: 34
DOI: 10.1002/JRS.4548
|
|
|
“Micro-Raman analysis for the identification of pigments from 19th and 20th century paintings”. Aibéo CL, Goffin S, Schalm O, van der Snickt G, Laquière N, Eyskens P, Janssens K, Journal of Raman spectroscopy 39, 1091 (2008). http://doi.org/10.1002/JRS.1990
Abstract: In this article, results using confocal µ-Raman to analyse the cross-section of paint samples are presented. Results obtained with light microscopy, scanning electron microscopy (SEM) combined with an energy dispersive X-ray analysis (EDX) and micro-X-ray fluorescence (µ-XRF) are mentioned and compared to the ones obtained with confocal (MRS). In some cases, pigment identification was possible only by combining analytical results from different techniques. The samples were drawn from five paintings belonging to the Academy of Fine Arts of Antwerp, which are part of a collection of 34 paintings made by students from the Academy between 1819 and 1920. Since, on the one hand, the painting techniques and materials, especially pigments, used in this period are still not completely known, and on the other hand, this collection constitutes a very important and reliable resource of information, these paintings were chosen for a systematic investigation. They represent the evolution of painting in Belgium over approximately a century.
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Impact Factor: 2.969
Times cited: 28
DOI: 10.1002/JRS.1990
|
|
|
“In vitro validation of a mobile Raman-XRF micro-analytical instrument's capabilities on the diagnosis of Byzantine icons”. Andrikopoulos KS, Daniilia S, Roussel B, Janssens K, Journal of Raman spectroscopy 37, 1026 (2006). http://doi.org/10.1002/JRS.1612
Keywords: A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation)
Impact Factor: 2.969
Times cited: 53
DOI: 10.1002/JRS.1612
|
|
|
“Structural transitions and long-time self-diffusion of interacting colloids confined by a parabolic potential”. Euan-Diaz E, Herrera-Velarde S, Misko VR, Peeters FM, Castaneda-Priego R, The journal of chemical physics 142, 024902 (2015). http://doi.org/10.1063/1.4905215
Abstract: We report on the ordering and dynamics of interacting colloidal particles confined by a parabolic potential. By means of Brownian dynamics simulations, we find that by varying the magnitude of the trap stiffness, it is possible to control the dimension of the system and, thus, explore both the structural transitions and the long-time self-diffusion coefficient as a function of the degree of confinement. We particularly study the structural ordering in the directions perpendicular and parallel to the confinement. Further analysis of the local distribution of the first-neighbors layer allows us to identify the different structural phases induced by the parabolic potential. These results are summarized in a structural state diagram that describes the way in which the colloidal suspension undergoes a structural re-ordering while increasing the confinement. To fully understand the particle dynamics, we take into account hydrodynamic interactions between colloids; the parabolic potential constricts the available space for the colloids, but it does not act on the solvent. Our findings show a non-linear behavior of the long-time self-diffusion coefficient that is associated to the structural transitions induced by the external field. (C) 2015 AIP Publishing LLC.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.965
Times cited: 7
DOI: 10.1063/1.4905215
|
|
|
“Electronic properties of graphene nano-flakes : energy gap, permanent dipole, termination effect, and Raman spectroscopy”. Singh SK, Neek-Amal M, Peeters FM, The journal of chemical physics 140, 074304 (2014). http://doi.org/10.1063/1.4865414
Abstract: The electronic properties of graphene nano-flakes (GNFs) with different edge passivation are investigated by using density functional theory. Passivation with F and H atoms is considered: C-Nc X-Nx (X = F or H). We studied GNFs with 10 < N-c < 56 and limit ourselves to the lowest energy configurations. We found that: (i) the energy difference Delta between the highest occupied molecular orbital and the lowest unoccupied molecular orbital decreases with N-c, (ii) topological defects (pentagon and heptagon) break the symmetry of the GNFs and enhance the electric polarization, (iii) the mutual interaction of bilayer GNFs can be understood by dipole-dipole interaction which were found sensitive to the relative orientation of the GNFs, (iv) the permanent dipoles depend on the edge terminated atom, while the energy gap is independent of it, and (v) the presence of heptagon and pentagon defects in the GNFs results in the largest difference between the energy of the spin-up and spin-down electrons which is larger for the H-passivated GNFs as compared to F-passivated GNFs. Our study shows clearly the effect of geometry, size, termination, and bilayer on the electronic properties of small GNFs. This study reveals important features of graphene nano-flakes which can be detected using Raman spectroscopy. (C) 2014 AIP Publishing LLC.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.965
Times cited: 30
DOI: 10.1063/1.4865414
|
|
|
“On the time scale associated with Monte Carlo simulations”. Bal KM, Neyts EC, The journal of chemical physics 141, 204104 (2014). http://doi.org/10.1063/1.4902136
Abstract: Uniform-acceptance force-bias Monte Carlo (fbMC) methods have been shown to be a powerful technique to access longer timescales in atomistic simulations allowing, for example, phase transitions and growth. Recently, a new fbMC method, the time-stamped force-bias Monte Carlo (tfMC) method, was derived with inclusion of an estimated effective timescale; this timescale, however, does not seem able to explain some of the successes the method. In this contribution, we therefore explicitly quantify the effective timescale tfMC is able to access for a variety of systems, namely a simple single-particle, one-dimensional model system, the Lennard-Jones liquid, an adatom on the Cu(100) surface, a silicon crystal with point defects and a highly defected graphene sheet, in order to gain new insights into the mechanisms by which tfMC operates. It is found that considerable boosts, up to three orders of magnitude compared to molecular dynamics, can be achieved for solid state systems by lowering of the apparent activation barrier of occurring processes, while not requiring any system-specific input or modifications of the method. We furthermore address the pitfalls of using the method as a replacement or complement of molecular dynamics simulations, its ability to explicitly describe correct dynamics and reaction mechanisms, and the association of timescales to MC simulations in general.
Keywords: A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 2.965
Times cited: 26
DOI: 10.1063/1.4902136
|
|
|
“An aggregate resource efficiency perspective on sustainability : a sustainable value application to the EU-15 countries”. Ang F, Van Passel S, Mathijs E, Ecological Economics 71, 99 (2011). http://doi.org/10.1016/J.ECOLECON.2011.08.008
Abstract: The Sustainable Value approach integrates the efficiency with regard to environmental, social and economic resources into a monetary indicator. It gained significant popularity as evidenced by diverse applications at the corporate level. However, its introduction as a measure adhering to the strong sustainability paradigm sparked an ardent debate. This study explores its validity as a macroeconomic strong sustainability measure by applying the Sustainable Value approach to the EU-15 countries. Concretely, we assessed environmental, social and economic resources in combination with the GDP for all EU-15 countries from 1995 to 2006 for three benchmark alternatives. The results show that several countries manage to adequately delink resource use from GDP growth. Furthermore, the remarkable difference in outcome between the national and EU-15 benchmark indicates a possible inefficiency of the current allocation of national resource ceilings imposed by the European institutions. Additionally, by using an effects model we argue that the service degree of the economy and governmental expenditures on social protection and research and development are important determinants of overall resource efficiency. Finally, we sketch out three necessary conditions to link the Sustainable Value approach to the strong sustainability paradigm. (C) 2011 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Economics
Impact Factor: 2.965
Times cited: 12
DOI: 10.1016/J.ECOLECON.2011.08.008
|
|
|
“The sustainable value approach : a clarifying and constructive comment”. Ang F, Van Passel S, Ecological Economics 69, 2303 (2010). http://doi.org/10.1016/J.ECOLECON.2010.05.016
Abstract: Recently, the original benchmarking methodology of the Sustainable Value approach became subjected to serious debate. While Kuosmanen and Kuosmanen (2009b) critically question its validity introducing productive efficiency theory, Figge and Hahn (2009) put forward that the implementation of productive efficiency theory severely conflicts with the original financial economics perspective of the Sustainable Value approach. We argue that the debate is very confusing because the original Sustainable Value approach presents two largely incompatible objectives. Nevertheless, we maintain that both ways of benchmarking could provide useful and moreover complementary insights. If one intends to present the overall resource efficiency of the firm from the investor's viewpoint, we recommend the original benchmarking methodology. If one on the other hand aspires to create a prescriptive tool setting up some sort of reallocation scheme, we advocate implementation of the productive efficiency theory. Although the discussion on benchmark application is certainly substantial, we should avoid the debate to become accordingly narrowed. Next to the benchmark concern, we see several other challenges considering the development of the Sustainable Value approach: (1) a more systematic resource selection, (2) the inclusion of the value chain and (3) additional analyses related to policy in order to increase interpretative power.
Keywords: A1 Journal article; Economics
Impact Factor: 2.965
Times cited: 18
DOI: 10.1016/J.ECOLECON.2010.05.016
|
|
|
“Orientational ordering in solid C60 fullerene-cubane”. Verberck B, Vliegenthart GA, Gompper G, The journal of chemical physics 130, 154510 (2009). http://doi.org/10.1063/1.3098550
Abstract: We study the structure and phase behavior of fullerene-cubane C60·C8H8 by Monte Carlo simulation. Using a simple potential model capturing the icosahedral and cubic symmetries of its molecular constituents, we reproduce the experimentally observed phase transition from a cubic to an orthorhombic crystal lattice and the accompanying rotational freezing of the C60 molecules. We elaborate a scheme to identify the low-temperature orientations of individual molecules and to detect a pattern of orientational ordering similar to the arrangement of C60 molecules in solid C60. Our configuration of orientations supports a doubled periodicity along one of the crystal axes.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.965
Times cited: 8
DOI: 10.1063/1.3098550
|
|
|
“Superposition of quantum and classical rotational motions in Sc2C2@C84 fullerite”. Michel KH, Verberck B, Hulman M, Kuzmany H, Krause M, The journal of chemical physics 126, 064304 (2007). http://doi.org/10.1063/1.2434175
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.965
Times cited: 14
DOI: 10.1063/1.2434175
|
|
|
“Measuring farm sustainability and explaining differences in sustainable efficiency”. Van Passel S, Nevens F, Mathijs E, Van Huylenbroeck G, Ecological Economics 62, 149 (2007). http://doi.org/10.1016/J.ECOLECON.2006.06.008
Abstract: A major objective of European agricultural policy is to have a sustainable and efficient farming sector that is applying environmentally-friendly production methods. Policy makers aim to combine a strong economic performance and a sustainable use of natural resources. Therefore, it is important to measure and to assess farm sustainability. For a large dataset of Flemish dairy farms, a valuation method that is based on the concept of opportunity costs is used to calculate and analyze differences among the sample farms with respect to the creation of sustainable value. But more important than measuring the creation of sustainable value is to analyze differences in sustainable efficiency. Therefore, sustainable efficiency measures are calculated and differences in sustainable efficiency are explained. Using panel data, an effect model captures the determinants of sustainable efficiency of the studied farms. The empirical model shows that, in general, larger farms have a higher sustainable efficiency. Also farmer's age and dependency on support payments proved to be determining characteristics for observed differences in sustainable efficiency.
Keywords: A1 Journal article; Economics
Impact Factor: 2.965
Times cited: 101
DOI: 10.1016/J.ECOLECON.2006.06.008
|
|
|
“Superexchange and electron correlations in alkali fullerides AC60, A=K, Rb, Cs”. Nikolaev AV, Michel KH, The journal of chemical physics 122, 064310 (2005). http://doi.org/10.1063/1.1844491
Abstract: Superexchange interactions in alkali fullerides AC(60) are derived for C-60 molecular ions separated by interstitial alkali-metal ions. We use a multiconfiguration approach which comprises the lowest molecular orbital states of the C-60 molecule and the excited s and d states of the alkali-metal atom A. Interactions are described by the valence bond (Heitler-London) method for a complex (C-60 – A – C-60) – with two valence electrons. The electronic charge transfer between the alkali-metal atom and a neighboring C-60 molecule is not complete. The occupation probability of excited d and s states of the alkali atom is not negligible. In correspondence with the relative positions of the C-60 molecules and A atoms in the polymer crystal, we consider 180degrees and 90degrees (angle) superexchange pathways. For the former case the ground state is found to be a spin singlet separated from a triplet at similar to20 K. For T < 20 K there appear strong spin correlations for the 180degrees superexchange pathway. The results are related to spin lattice relaxation experiments on CsC60 in the polymerized and in the quenched cubic phase. (C) 2005 American Institute of Physics.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.965
Times cited: 11
DOI: 10.1063/1.1844491
|
|
|
“Valence electronic charge density of distorted C60-monomers in polymerized KC60 and RbC60”. Verberck B, Popov VN, Nikolaev AV, Lamoen D, The journal of chemical physics 121, 321 (2004). http://doi.org/10.1063/1.1755676
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.965
Times cited: 7
DOI: 10.1063/1.1755676
|
|
|
“Crystal structures of polymerized fullerides AC60, A=K, Rb, Cs, and alkali-mediated interactions”. Verberck B, Michel KH, Nikolaev AV, The journal of chemical physics 116, 10462 (2002). http://doi.org/10.1063/1.1475745
Abstract: Starting from a model of rigid interacting C-60 polymer chains on an orthorhombic lattice, we study the mutual orientation of the chains and the stability of the crystalline structures Pmnn and I2/m. We take into account (i) van der Waals interactions and electric quadrupole interactions between C-60 monomers on different chains as well as (ii) interactions of the monomers with the surrounding alkali atoms. The direct interactions (i) always lead to an antiferrorotational structure Pmnn with alternate orientation of the C-60 chains in planes (001). The interactions (ii) with the alkalis consist of two parts: translation-rotation (TR) coupling where the orientations of the chains interact with displacements of the alkalis, and quadrupolar electronic polarizability (ep) coupling, where the electric quadrupoles on the C-60 monomers interact with induced quadrupoles due to excited electronic d-states of the alkalis. Both interactions (ii) lead to an effective orientation-orientation interaction between the C-60 chains and always favor the ferrorotational structure I2/m, where C-60 chains have a same orientation. The structures Pmnn for KC60 and I2/m for Rb- and CsC60 are the result of a competition between the direct interaction (i) and the alkali-mediated interactions (ii). In Rb- and CsC60 the latter are found to be dominant, the preponderant role being played by the quadrupolar electronic polarizability of the alkali ions. (C) 2002 American Institute of Physics.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.965
Times cited: 12
DOI: 10.1063/1.1475745
|
|
|
“Single chain elasticity and thermoelasticity of polyethylene”. Titantah JT, Pierleoni C, Ryckaert J-P, The journal of chemical physics 117, 9028 (2002). http://doi.org/10.1063/1.1514974
Abstract: Single-chain elasticity of polyethylene at theta point up to 90% of stretching with respect to its contour length is computed by Monte Carlo simulation of an atomistic model in continuous space. The elasticity law together with the free-energy and the internal energy variations with stretching are found to be very well represented by the wormlike chain model up to 65% of the chain elongation, provided the persistence length is treated as a temperature-dependent parameter. Beyond this value of elongation simple ideal chain models are not able to describe the Monte Carlo data in a thermodynamic consistent way. This study reinforces the use of the wormlike chain model to interpret experimental data on the elasticity of synthetic polymers in the finite extensibility regime, provided the chain is not yet in its fully stretched regime. Specific solvent effects on the elasticity law and the partition between energetic and entropic contributions to single chain elasticity are investigated. (C) 2002 American Institute of Physics.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.965
Times cited: 5
DOI: 10.1063/1.1514974
|
|
|
“Thermodynamic consistency and integral equations for the liquid structure”. Leys FE, March NH, Lamoen D, Journal Of Chemical Physics 117, 10726 (2002). http://doi.org/10.1063/1.1522377
Keywords: A1 Journal article; Electron Microscopy for Materials Science (EMAT);
Impact Factor: 2.965
DOI: 10.1063/1.1522377
|
|
|
“Adsorption of potassium and oxygen on graphite: a theoretical study”. Lamoen D, Persson BNJ, Journal Of Chemical Physics 108, 3332 (1998). http://doi.org/10.1063/1.475732
Keywords: A1 Journal article; Electron Microscopy for Materials Science (EMAT);
Impact Factor: 2.965
Times cited: 91
DOI: 10.1063/1.475732
|
|
|
“Charge transfer and polymer phases in AC60 (A=K, Rb, Cs) fullerides”. Nikolaev AV, Prassides K, Michel KH, The journal of chemical physics 108, 4912 (1998). http://doi.org/10.1063/1.475900
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.965
Times cited: 14
DOI: 10.1063/1.475900
|
|
|
“Extension of the basis set of linearized augmented plane wave (LAPW) method by using supplemented tight binding basis functions”. Nikolaev AV, Lamoen D, Partoens B, The journal of chemical physics 145, 014101 (2016). http://doi.org/10.1063/1.4954962
Abstract: In order to increase the accuracy of the linearized augmented plane wave (LAPW) method, we present a new approach where the plane wave basis function is augmented by two different atomic radial components constructed at two different linearization energies corresponding to two different electron bands (or energy windows). We demonstrate that this case can be reduced to the standard treatment within the LAPW paradigm where the usual basis set is enriched by the basis functions of the tight binding type, which go to zero with zero derivative at the sphere boundary. We show that the task is closely related with the problem of extended core states which is currently solved by applying the LAPW method with local orbitals (LAPW+LO). In comparison with LAPW+LO, the number of supplemented basis functions in our approach is doubled, which opens up a new channel for the extension of the LAPW and LAPW+LO basis sets. The appearance of new supplemented basis functions absent in the LAPW+LO treatment is closely related with the existence of the ul-component in the canonical LAPW method. We discuss properties of additional tight binding basis functions and apply the extended basis set for computation of electron energy bands of lanthanum (face and body centered structures) and hexagonal close packed lattice of cadmium. We demonstrate that the new treatment gives lower total energies in comparison with both canonical LAPW and LAPW+LO, with the energy difference more pronounced for intermediate and poor LAPW basis sets.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT); Condensed Matter Theory (CMT)
Impact Factor: 2.965
Times cited: 11
DOI: 10.1063/1.4954962
|
|
|
“Monitoring the effect of asymmetrical vertical strain on Janus single layers of MoSSe via spectrum”. Kandemir A, Peeters FM, Sahin H, The journal of chemical physics 149, 084707 (2018). http://doi.org/10.1063/1.5043207
Abstract: Using first principles calculations, we study the structural and phononic properties of the recently synthesized Janus type single layers of molybdenum dichalcogenides. The Janus MoSSe single layer possesses 2H crystal structure with two different chalcogenide sides that lead to out-of-plane anisotropy. By virtue of the asymmetric structure of the ultra-thin Janus type crystal, we induced the out-of-plane anisotropy to show the distinctive vertical pressure effect on the vibrational properties of the Janus material. It is proposed that for the corresponding Raman active optical mode of the Janus structure, the phase modulation and the magnitude ratio of the strained atom and its first neighbor atom adjust the distinctive change in the eigen-frequencies and Raman activity. Moreover, a strong variation in the Raman activity of the Janus structure is obtained under bivertical and univertical strains. Not only eigen-frequency shifts but also Raman activities of the optical modes of the Janus structure exhibit distinguishable features. This study reveals that the vertical anisotropic feature of the Janus structure under Raman measurement allows us to distinguish which side of the Janus crystal interacts with the externals (substrate, functional adlayers, or dopants). Published by AIP Publishing.
Keywords: A1 Journal article; Condensed Matter Theory (CMT)
Impact Factor: 2.965
Times cited: 11
DOI: 10.1063/1.5043207
|
|
|
“Quantification of the indirect use value of functional group diversity based on the ecological role of species in the ecosystem”. Daniels S, Bellmore JR, Benjamin JR, Witters N, Vangronsveld J, Van Passel S, Ecological Economics 153, 181 (2018). http://doi.org/10.1016/J.ECOLECON.2018.04.027
Abstract: An important issue in biodiversity valuation is gaining a better understanding of how biodiversity conservation affects economic activities and human welfare. Quantifying the economic benefits of biodiversity for human well-being is not straightforward. Here, we expand the ecosystem service cascade by (i) attributing a methodology to the different steps of the cascade to assess the effects of changes in functional group diversity on economic activities; (ii) including multiple attributes for defining functional diversity and (iii) integrating a dynamic ecological model simulating complex interactions and feedbacks between species with an economic model assessing the effects of changes in functional group diversity for gross revenues. The stepwise methodological framework integrates a production function approach with a market price-based approach in order to investigate the indirect use value of functional group diversity based on the ecological role of species in the ecosystem. The methodology is applied to estimate the relationship between the gross economic value of Chinook salmon (Pacific Northwest, United States) and the diversity of freshwater macroinvertebrates. The results of our analysis emphasize the importance of biological diversity for sustaining ecosystem goods and services. The analysis provides a tractable framework for quantitatively exploring the economic consequences of changes in functional group diversity.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
Impact Factor: 2.965
DOI: 10.1016/J.ECOLECON.2018.04.027
|
|
|
“Organic farming and small-scale farmers : main opportunities and challenges”. Jouzi Z, Azadi H, Taheri F, Zarafshani K, Gebrehiwot K, Van Passel S, Lebailly P, Ecological Economics 132, 144 (2017). http://doi.org/10.1016/J.ECOLECON.2016.10.016
Abstract: Producing enough food to meet the needs of a growing population has always been the greatest concern of food policy-makers around the world. Given the increasing attention to organic farming (OF), we conducted this study to investigate the main opportunities and challenges of the food production system of small-scale farmers in developing countries with an emphasis on their livelihoods. The study showed that the most significant advantages of OF are environmental protection and a higher resilience to environmental changes, increasing farmers' income and reducing external input cost, enhancing social capacity and increasing employment opportunities. A s well as enhancing food security primarily by increasing the food purchasing power of local people. However, the main challenges of this food production system include lower yields in comparison to conventional systems, difficulties with soil nutrient management, certification and market barriers, and the educational and research needs of small-holders. The paper concludes that even though OF might present some significant challenges to small-scale farmers, it could/should still be considered as a part of the solution and means of improving their livelihoods.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
Impact Factor: 2.965
Times cited: 39
DOI: 10.1016/J.ECOLECON.2016.10.016
|
|
|
“Monetary valuation of natural predators for biological pest control in pear production”. Daniels S, Witters N, Beliën T, Vrancken K, Vangronsveld J, Van Passel S, Ecological Economics 134, 160 (2017). http://doi.org/10.1016/J.ECOLECON.2016.12.029
Abstract: In spite of global actions, biodiversity is declining at an alarming rate. Despite the need for objectively comparable monetary standards to include biodiversity arguments in policymaking, research on the relationship between species diversity and its valuation from a societal perspective is still scarce. In this paper, a methodological framework for the valuation of natural predators based on their ecological role in the agroecosystem is introduced. The framework integrates a dynamic ecological model simulating interactions between species with an economic model, thereby quantifying the effect of reduced numbers of natural predators on the net farm income. The model attributes an objective monetary value to increased species diversity through the changes in the provisioning of a marketable good. Results indicate that the loss of three predators could decrease net farm income with 88.86 ha− 1 to 2186.5 ha− 1. For the pear production sector in Flanders in 2011, this constitutes to an indirect use value of 0,68 million for one predator and 16.63 million for the presence of three predators. The aim is to provide a justification for the argument for biodiversity conservation, based on the ecological function of species, through the delivery of comparable monetary standards.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
Impact Factor: 2.965
Times cited: 4
DOI: 10.1016/J.ECOLECON.2016.12.029
|
|
|
“Impacts of the Hara biosphere reserve on livelihood and welfare in Persian Gulf”. Pour MD, Motiee N, Barati AA, Taheri F, Azadi H, Gebrehiwot K, Lebailly P, Van Passel S, Witlox F, Ecological Economics 141, 76 (2017). http://doi.org/10.1016/J.ECOLECON.2017.05.023
Abstract: Despite the importance of biosphere reserves in Iran's livelihood and welfare, the economic significance of Hara Biosphere Reserve has never been comprehensively studied. This study examines the current importance of Hara Biosphere Reserve (HBR) in local livelihood and welfare. Using a household survey, data were collected through a questionnaire, key informant interviews and direct observations. Two hundred and forty-four households were randomly selected from 10 villages through proportional sampling. Results showed that non-environmental income was the first driver of the total income, poverty alleviation and narrowing income inequality gap. Park income was the second. The results also showed that excluding park income from total income would significantly increase headcount poverty, widen the poverty gap, and raise the Gini coefficient. Wealthier households had the greatest absolute income from the environment, including forest, fishing and fodder. However, the poorest group had smallest absolute income from these sources. Thus, the study demonstrated that wealthier households are responsible for the overharvesting of environmental resources. Interestingly, the study showed that wealthier households are more dependent on profitable environmental incomes sources while the poorest are more dependent on non-profitable ones. (C) 2017 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Economics; Engineering Management (ENM)
Impact Factor: 2.965
Times cited: 7
DOI: 10.1016/J.ECOLECON.2017.05.023
|
|