Records |
Author |
Cremers, V.; Rampelberg, G.; Baert, K.; Abrahami, S.; Claes, N.; de Oliveira, T.M.; Terryn, H.; Bals, S.; Dendooven, J.; Detavernier, C. |
Title |
Corrosion protection of Cu by atomic layer deposition |
Type |
A1 Journal article |
Year |
2019 |
Publication |
Journal of vacuum science and technology: A: vacuum surfaces and films |
Abbreviated Journal |
J Vac Sci Technol A |
Volume |
37 |
Issue |
37 |
Pages |
060902 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Atomic layer deposition (ALD) is a vapor phase technique that is able to deposit uniform, conformal thin films with an excellent thickness control at the atomic scale. 18 nm thick Al2O3 and TiO2 coatings were deposited conformaly and pinhole-free onto micrometer-sized Cu powder, using trimethylaluminum and tetrakis(dimethylamido)titanium(IV), respectively, as a precursor and de-ionized water as a reactant. The capability of the ALD coating to protect the Cu powder against corrosion was investigated. Therefore, the stability of the coatings was studied in solutions with different pH in the range of 0–14, and in situ raman spectroscopy was used to detect the emergence of corrosion products of Cu as an indication that the protective coating starts to fail. Both ALD coatings provide good protection at standard pH values in the range of 5–7. In general, the TiO2 coating shows a better barrier protection against corrosion than the Al2O3 coating. However, for the most extreme pH conditions, pH 0 and pH 14, the TiO2 coating starts also to degrade. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000517925800003 |
Publication Date |
2019-09-19 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0734-2101 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
1.374 |
Times cited |
7 |
Open Access |
OpenAccess |
Notes |
The authors acknowledge financial support from the Strategic Initiative Materials in Flanders (SIM, SBO-FUNC project) and the Special Research Fund BOF of Ghent University (No. GOA 01G01513). J.D. acknowledges the Research Foundation Flanders (FWO-Vlaanderen) for a postdoctoral fellowship. |
Approved |
Most recent IF: 1.374 |
Call Number |
EMAT @ emat @c:irua:162640 |
Serial |
5361 |
Permanent link to this record |
|
|
|
Author |
Sharp, J.; Mueller, I.C.; Mandal, P.; Abbas, A.; Nord, M.; Doye, A.; Ehiasarian, A.; Hovsepian, P.; MacLaren, I.; Rainforth, W.M. |
Title |
Characterisation of a high-power impulse magnetron sputtered C/Mo/W wear resistant coating by transmission electron microscopy |
Type |
A1 Journal article |
Year |
2019 |
Publication |
Surface and coatings technology |
Abbreviated Journal |
Surf Coat Tech |
Volume |
377 |
Issue |
377 |
Pages |
124853 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Thin films of C/Mo/W deposited using combined UBM/HIPIMS sputtering show 2-8 nm clusters of material richer in Mo and W than the matrix (found by EDS microanalysis), with structures that resemble graphitic onions with the metal atoms arranged regularly within them. EELS microanalysis showed the clusters to be rich in W and Mo. As the time averaged power used in the pulsed HIPIMS magnetron was increased, the clusters became more defined, larger, and arranged into layers with amorphous matrix between them. Films deposited with average HIPIMS powers of 4 kW and 6 kW also showed a periodic modulation of the cluster density within the finer layers giving secondary, wider stripes in TEM. By analysing the ratio between the finer and coarser layers, it was found that this meta-layering is related to the substrate rotation in the deposition chamber but in a non-straightforward way. Reasons for this are proposed. The detailed structure of the clusters remains unknown and is the subject of further work. Fluctuation electron microscopy results indicated the presence of crystal planes with the graphite interlayer spacing, crystal planes in hexagonal WC perpendicular to the basal plane, and some plane spacings found in Mo2C. Other peaks in the FEM results suggested symmetry-related starting points for future determination of the structure of the clusters. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000488417800015 |
Publication Date |
2019-08-03 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0257-8972 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.589 |
Times cited |
1 |
Open Access |
|
Notes |
; J.S. thanks the Mercury Centre at the University of Sheffield for funding, which was part funded by the ERDF under grant MERCURY 904467. I.C.M. acknowledges support from CONACyT and RobertoRocca Education Fellowship. We gratefully acknowledge funding from EPSRC for the pixelated STEM detector and the software used in its operation for the fluctuation microscopy (EP/M009963/ 1, EP/K503903/1 & EP/R511705/1). AD was supported by the EPSRC CDT in Integrative Sensing and Measurement, Grant Number EP/L016753/1. Funding sources did not influence the planning or execution of this work except to enable it. ; |
Approved |
Most recent IF: 2.589 |
Call Number |
UA @ admin @ c:irua:163700 |
Serial |
5383 |
Permanent link to this record |
|
|
|
Author |
Shah, N.A.; Li, L.L.; Mosallanejad, V.; Peeters, F.M.; Guo, G.-P. |
Title |
Transport characteristics of multi-terminal pristine and defective phosphorene systems |
Type |
A1 Journal article |
Year |
2019 |
Publication |
Nanotechnology |
Abbreviated Journal |
Nanotechnology |
Volume |
30 |
Issue |
45 |
Pages |
455705 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT) |
Abstract |
Atomic vacancies and nanopores act as local scattering centers and modify the transport properties of charge carriers in phosphorene nanoribbons (PNRs). We investigate the influence of such atomic defects on the electronic transport of multi-terminal PNR. We use the non-equilibrium Green's function approach within the tight-binding framework to calculate the transmission coefficient and the conductance. Terminals induce band mixing resulting in oscillations in the conductance. In the presence of atomic vacancies and nanopores the conductance between non-axial terminals exhibit constructive scattering, which is in contrast to mono-axial two-terminal systems where the conductance exhibits destructive scattering. This can be understood from the spatial local density of states of the transport modes in the system. Our results provide fundamental insights into the electronic transport in PNR-based multi-terminal systems and into the ability of atomic defects and nanopores through tuning the transport properties. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000483049100001 |
Publication Date |
2019-08-07 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0957-4484 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.44 |
Times cited |
8 |
Open Access |
|
Notes |
; This work was supported by the National Key Research and Development Program of China (Grant No. 2016YFA0301700), the NNSFC (Grant No. 11625419), the Strategic Priority Research Program of the CAS (Grant Nos. XDB24030601 and XDB30000000), the Anhui initiative in Quantum information Technologies (Grants No. AHY080000), and the Flemish Science Foundation (FWO-Vl). This work was also supported by the Chinese Academy of Sciences and the World Academy of Science for the advancement of science in developing countries. ; |
Approved |
Most recent IF: 3.44 |
Call Number |
UA @ admin @ c:irua:162760 |
Serial |
5429 |
Permanent link to this record |
|
|
|
Author |
Prabhakara, V.; Jannis, D.; Béché, A.; Bender, H.; Verbeeck, J. |
Title |
Strain measurement in semiconductor FinFET devices using a novel moiré demodulation technique |
Type |
A1 Journal article |
Year |
2019 |
Publication |
Semiconductor science and technology |
Abbreviated Journal |
Semicond Sci Tech |
Volume |
|
Issue |
|
Pages |
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
Abstract |
Moiré fringes are used throughout a wide variety of applications in physics and
engineering to bring out small variations in an underlying lattice by comparing with another reference lattice. This method was recently demonstrated in Scanning Transmission Electron Microscopy imaging to provide local strain measurement in crystals by comparing the crystal lattice with the scanning raster that then serves as the reference. The images obtained in this way contain a beating fringe pattern with a local period that represents the deviation of the lattice from the reference. In order to obtain the actual strain value, a region containing a full period of the fringe is required, which results in a compromise between strain sensitivity and spatial resolution. In this paper we propose an advanced setup making use of an optimised scanning pattern and a novel phase stepping demodulation scheme. We demonstrate the novel method on a series of 16 nm Si-Ge semiconductor FinFET devices in which strain plays a crucial role in modulating the charge carrier mobility. The obtained results are compared with both Nano-beam diffraction and the recently proposed Bessel beam diffraction technique. The setup provides a much improved spatial resolution over conventional moiré imaging in STEM while at the same time being fast and requiring no specialised diffraction camera as opposed to the diffraction techniques we compare to. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000537721200002 |
Publication Date |
2019-11-29 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0268-1242 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.305 |
Times cited |
8 |
Open Access |
|
Notes |
The Qu-Ant-EM microscope and the direct electron detector used in the diffraction experiments was partly funded by the Hercules fund from the Flemish Government. This project has received funding from the GOA project “Solarpaint” of the University of Antwerp. We would also like to thank Dr. Thomas Nuytten and Prof. Dr. Wilfried Vandervorst from IMEC, Leuven for their continuous support and collaboration with the project. |
Approved |
Most recent IF: 2.305 |
Call Number |
EMAT @ emat @c:irua:165794 |
Serial |
5445 |
Permanent link to this record |
|
|
|
Author |
Terzano, R.; Spagnuolo, M.; Vekemans, B.; de Nolf, W.; Janssens, K.; Falkenberg, G.; Ruggiero, P. |
Title |
Assessing the origin and fate of CR, Ni, Cu, Zn, Ph, and V in industrial polluted soil by combined microspectroscopic techniques and bulk extraction methods |
Type |
A1 Journal article |
Year |
2007 |
Publication |
Environmental science & technology |
Abbreviated Journal |
|
Volume |
41 |
Issue |
19 |
Pages |
6762-6769 |
Keywords |
A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000249840600024 |
Publication Date |
2007-08-29 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
|
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
61 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: NA |
Call Number |
UA @ admin @ c:irua:66622 |
Serial |
5481 |
Permanent link to this record |
|
|
|
Author |
Denecke, M.A.; Janssens, K.; Proost, K.; Rothe, J.; Noseck, U. |
Title |
Confocal micrometer-scale X-ray fluorescence and X-ray absorption fine structure studies of uranium speciation in a tertiary sediment from a waste disposal natural analogue site |
Type |
A1 Journal article |
Year |
2005 |
Publication |
Environmental science and technology |
Abbreviated Journal |
Environ Sci Technol |
Volume |
39 |
Issue |
|
Pages |
2049-2058 |
Keywords |
A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation) |
Abstract |
|
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000228172600031 |
Publication Date |
2005-03-30 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0013-936x; 1520-5851 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
6.198 |
Times cited |
47 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 6.198; 2005 IF: 4.054 |
Call Number |
UA @ admin @ c:irua:52232 |
Serial |
5554 |
Permanent link to this record |
|
|
|
Author |
Terzano, R.; Spagnuolo, M.; Medici, L.; Vekemans, B.; Vincze, L.; Janssens, K.; Ruggiero, P. |
Title |
Copper stabilization by zeolite synthesis in polluted soils treated with coal fly ash |
Type |
A1 Journal article |
Year |
2005 |
Publication |
Environmental science and technology |
Abbreviated Journal |
Environ Sci Technol |
Volume |
39 |
Issue |
16 |
Pages |
6280-6287 |
Keywords |
A1 Journal article; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation) |
Abstract |
This study deals with the process of zeolite formation in an agricultural soil artificially polluted by high amounts of Cu (15 mg of Cu/g of soil dry weight) and treated with fused coal fly ash at 30 and 60 degrees C and how this process affects the mobility and availability of the metal. As a consequence of the treatment, the amount of dissolved Cu, and thus its mobility, was strongly reduced, and the percentage of the metal stabilized in the solid phase increased over time, reaching values of 30% at 30 degrees C and 40% at 60 degrees C. The physicochemical phenomena responsible for Cu stabilization in the solid phase have been evaluated by EDTA sequential extractions and synchrotron radiation based X-ray microanalytical techniques. These techniques were used for the visualization of the spatial distribution and the speciation of Cu in and/or on the neo-formed zeolite particles. In particular, micro XRF (X-ray fluorescence) tomography showed direct evidence that Cu can be entrapped as clusters inside the porous zeolitic structures while,mu-XANES (X-ray absorption near edge structure) spectroscopy determinations revealed Cu to be present mainly as Cu(II) hydroxide and Cu(II) oxide. The reported results could be useful as a basic knowledge for planning new technologies for the on site physicochemical stabilization of heavy metals in heavily polluted soils. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000231203100053 |
Publication Date |
2005-08-11 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0013-936x; 1520-5851 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
6.198 |
Times cited |
39 |
Open Access |
|
Notes |
|
Approved |
Most recent IF: 6.198; 2005 IF: 4.054 |
Call Number |
UA @ admin @ c:irua:103658 |
Serial |
5560 |
Permanent link to this record |
|
|
|
Author |
Rather, J.A.; Pilehvar, S.; De Wael, K. |
Title |
Polycyclodextrin and carbon nanotubes as composite for tyrosinase immobilization and its superior electrocatalytic activity towards butylparaben an endocrine disruptor |
Type |
A1 Journal article |
Year |
2015 |
Publication |
Journal of nanoscience and nanotechnology |
Abbreviated Journal |
|
Volume |
15 |
Issue |
5 |
Pages |
3365-3372 |
Keywords |
A1 Journal article; Engineering sciences. Technology; AXES (Antwerp X-ray Analysis, Electrochemistry and Speciation) |
Abstract |
We developed a protocol for the immobilization of tyrosinase (Tyr) on the composite of polycyclodextrin polymer (CDP) and carbon nanotubes for the detection of an endocrine disruptor, i.e., butylparaben (BP). The formation of the CDP polymer was characterized by UV-Vis spectrophotometry. The conducting film of cross-linked CDP and carbon nanotubes, displays excellent matrix capabilities for Tyr immobilization. The host-guest chemical reaction ability of CD and the ππ stacking interaction assure the bioactivity of Tyr towards butylparaben. The developed biosensor was characterized electrochemically by electrochemical impedance spectroscopy. The enzyme-substrate kinetic parameters such as the apparent Michaelis-Menten constant (K M app) was measured under saturated substrate concentration. The determination of butylparaben was carried out by using square wave voltammetry over the concentration range of 2.1 to 35.4 μM with a detection limit of 0.1 μM. The fabricated biosensor was successfully applied in real-life cosmetic samples with good recovery ranging from 98.5 to 102.8%. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000347435200007 |
Publication Date |
2014-10-01 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1533-4899 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
3 |
Open Access |
|
Notes |
; The authors are highly thankful for the mobility grant (Non-Europe Postdoc Fellowship) for one of the author (Jahangir Ahmad Rather) supported by the Belgian Federal Science Policy (Belspo) co-funded by the Marie Curie Actions from the European Commission. Sanaz Pilehvar is funded by BOF-DOCPRO UA. ; |
Approved |
Most recent IF: NA |
Call Number |
UA @ admin @ c:irua:119550 |
Serial |
5776 |
Permanent link to this record |
|
|
|
Author |
De Baere, K.; Verstraelen, H.; Willemen, R.; Smet, J.-P.; Tchuindjang, J.T.; Lecomte-Beckers, J.; Lenaerts, S.; Meskens, R.; Jung, H.G.; Potters, G. |
Title |
Assessment of corrosion resistance, material properties, and weldability of alloyed steel for ballast tanks |
Type |
A1 Journal article |
Year |
2017 |
Publication |
Journal of marine science and technology |
Abbreviated Journal |
J Mar Sci Tech-Japan |
Volume |
22 |
Issue |
1 |
Pages |
176-199 |
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
Abstract |
Ballast tanks are of great importance in the lifetime of modern merchant ships. Making a ballast tank less susceptible to corrosion can, therefore, prolong the useful life of a ship and, thereby, lower its operational cost. An option to reinforce a ballast tank is to construct it out of a corrosion-resistant steel type. Such steel was recently produced by POSCO Ltd., South Korea. After 6 months of permanent immersion, the average corrosion rate of A and AH steel (31 samples) was 535 g m(-2) year(-1), while the Korean CRS was corroding with 378 g m(-2) year(-1). This entails a gain of 29 %. Follow-up measurements after 10, 20, and 24 months confirmed this. The results after 6 months exposure to alternating wet/dry conditions are even more explicit. Furthermore, the physical and metallurgical properties of this steel show a density of 7.646 t/m(3), the elasticity modulus 209.3 GPa, the tensile strength 572 MPa, and the hardness 169HV10. Microscopically, the metal consists of equiaxed and recrystallized grains (ferrite and pearlite), with an average size of between 20 and 30 A mu m (ASTM E 112-12 grain size number between 7 and 8) with a few elongated pearlitic grains. The structure is banded ferrite/pearlite. On the basis of a series of energy dispersive X-ray spectrometer measurements the lower corrosion rate of the steel can be attributed to the interplay of Al, Cr, their oxides, and the corroding steel. In addition, the role of each element in the formation of oxide layers and the mechanisms contributing to the corrosion resistance are discussed. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000395006400015 |
Publication Date |
2016-07-21 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0948-4280 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
0.838 |
Times cited |
3 |
Open Access |
|
Notes |
; This paper is published with the explicit permission of POSCO Ltd., original source of the corrosion resistant steel. Due to the creativity of the POSCO engineers and scientists, we could have our challenge, presented in this manuscript. The authors wish to thank the BOF funding received from the University of Antwerp and the Maritime Academy. We also wish to express our gratitude towards to the American Bureau of Shipping for their assistance in procuring the CRS plates, their moral and financial support, as well as to OCAS (Arcelor Mittal, Zelzate, Belgium) for their assistance in a number of measurements. ; |
Approved |
Most recent IF: 0.838 |
Call Number |
UA @ admin @ c:irua:142509 |
Serial |
5928 |
Permanent link to this record |
|
|
|
Author |
Deng, S.; Verbruggen, S.W.; Lenaerts, S.; Martens, J.A.; Van den Berghe, S.; Devloo-Casier, K.; Devulder, W.; Dendoover, J.; Deduytsche, D.; Detavernier, C. |
Title |
Controllable nitrogen doping in as deposited TiO2 film and its effect on post deposition annealing |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Journal of vacuum science and technology: A: vacuum surfaces and films |
Abbreviated Journal |
J Vac Sci Technol A |
Volume |
32 |
Issue |
1 |
Pages |
01a123 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
Abstract |
In order to narrow the band gap of TiO2, nitrogen doping by combining thermal atomic layer deposition (TALD) of TiO2 and plasma enhanced atomic layer deposition (PEALD) of TiN has been implemented. By altering the ratio between TALD TiO2 and PEALD TiN, the as synthesized TiOxNy films showed different band gaps (from 1.91 eV to 3.14 eV). In situ x-ray diffraction characterization showed that the crystallization behavior of these films changed after nitrogen doping. After annealing in helium, nitrogen doped TiO2 films crystallized into rutile phase while for the samples annealed in air a preferential growth of the anatase TiO2 along (001) orientation was observed. Photocatalytic tests of the degradation of stearic acid were done to evaluate the effect of N doping on the photocatalytic activity. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000335847600023 |
Publication Date |
2013-12-16 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0734-2101 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
1.374 |
Times cited |
10 |
Open Access |
|
Notes |
; The authors wish to thank the Research Foundation-Flanders (FWO) for financial support. The authors acknowledge the European Research Council for funding under the European Union's Seventh Framework Programme (FP7/2007-2013)/ERC grant agreement Nos. 239865-COCOON and 246791-COUNTATO. The authors also acknowledge the support from UGENT-GOA-01G01513 and IWT-SBO SOSLion. J.A.M. acknowledges the Flemish government for long-term structural funding (Methusalem). J.D. acknowledges the Flemisch FWO for a postdoctoral fellowship. ; |
Approved |
Most recent IF: 1.374; 2014 IF: 2.322 |
Call Number |
UA @ admin @ c:irua:117296 |
Serial |
5936 |
Permanent link to this record |
|
|
|
Author |
Verbruggen, S.W.; Masschaele, K.; Moortgat, E.; Korany, T.E.; Hauchecorne, B.; Martens, J.A.; Lenaerts, S. |
Title |
Factors driving the activity of commercial titanium dioxide powders towards gas phase photocatalytic oxidation of acetaldehyde |
Type |
A1 Journal article |
Year |
2012 |
Publication |
Catalysis science & technology |
Abbreviated Journal |
Catal Sci Technol |
Volume |
2 |
Issue |
11 |
Pages |
2311-2318 |
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
Abstract |
The photocatalytic activity of two commercial titanium dioxide powders (Cristal Global, Millennium PC500 and Evonik, P25) is compared towards acetaldehyde degradation in the gas phase. In contrast to the extensive literature available, we found a higher activity for the PC500 than for the P25 coating. Here, we present a comprehensive characterization of the bulk and surface properties of both powders. Our comparison shows that the material properties that dominate the overall photocatalytic activity in gas phase differ from those required for the photodegradation of water-borne pollutants. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000310863900020 |
Publication Date |
2012-06-13 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
2044-4753; 2044-4761 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
5.773 |
Times cited |
33 |
Open Access |
|
Notes |
; S.W.V. acknowledges the Research Foundation of Flanders (FWO) for the financial support. J.A.M acknowledges long term funding (Methusalem). ; |
Approved |
Most recent IF: 5.773; 2012 IF: 3.753 |
Call Number |
UA @ admin @ c:irua:105162 |
Serial |
5952 |
Permanent link to this record |
|
|
|
Author |
De Baere, K.; Verstraelen, H.; Lemmens, L.; Lenaerts, S.; Dewil, R.; Van Ingelgem, Y.; Potters, G. |
Title |
A field study of the effectiveness of sacrificial anodes in ballast tanks of merchant ships |
Type |
A1 Journal article |
Year |
2014 |
Publication |
Journal of marine science and technology |
Abbreviated Journal |
J Mar Sci Tech-Japan |
Volume |
19 |
Issue |
1 |
Pages |
116-123 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
Abstract |
Sacrificial anodes have become a standard practice for the protection of ballast tanks of merchant vessels against corrosive damage. A well protected tank should extend the life span of a ship and consequently enhances its economic value. An in situ survey comprising more than 100 merchant vessels provided the opportunity to measure the impact of these anodes on the life expectancy of these vessels. Contrary to the general belief of these anodes beneficial effect, no significant difference was found in our observations in terms of corrosion occurrence between ship populations with and without sacrificial anodes, across all ship ages. This may be explained by the highly variable conditions and the complex geometry in a ballast tank severely impede optimal and straightforward installation of these anodes in these tanks. Also, poorly placed anodes in it may harm the integrity of the coating of the tank. We therefore plead for uniform and clear rules on anode installation and inspection. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000332693300008 |
Publication Date |
2013-07-29 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0948-4280 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
0.838 |
Times cited |
3 |
Open Access |
|
Notes |
; This work was financed by a BOF Academisation grant of the University of Antwerp and the Antwerp Maritime Academy. ; |
Approved |
Most recent IF: 0.838; 2014 IF: 0.805 |
Call Number |
UA @ admin @ c:irua:109348 |
Serial |
5953 |
Permanent link to this record |
|
|
|
Author |
Tytgat, T.; Smits, M.; Lenaerts, S.; Verbruggen, S.W. |
Title |
Immobilization of TiO2 into self-supporting photocatalytic foam : influence of calcination temperature |
Type |
A1 Journal article |
Year |
2014 |
Publication |
International journal of applied ceramic technology |
Abbreviated Journal |
Int J Appl Ceram Tec |
Volume |
11 |
Issue |
4 |
Pages |
714-722 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
Abstract |
Immobilization of photocatalytic powder is crucial to obtain industrially relevant purification processes. To achieve this goal, self-supporting TiO2 foams were manufactured by a polyacrylamide gel process. These gels were calcined at different temperatures to study the effect of the calcination temperature on foam characteristics (rigidity, crystallinity, and porosity) and its influence on photocatalytic activity. The results show that an optimal degradation is achieved for those foams calcined between 700 and 800°C. Calcination at higher temperatures results in a steep decrease in activity, explained by stability issues of the material due to formation of Na2SO4 phases and a larger rutile fraction. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000339051500012 |
Publication Date |
2013-04-24 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1546-542x |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
1.048 |
Times cited |
2 |
Open Access |
|
Notes |
; This work was supported by a PhD grant from the Institute of Innovation by Science and Technology in Flanders (IWT). ; |
Approved |
Most recent IF: 1.048; 2014 IF: 1.320 |
Call Number |
UA @ admin @ c:irua:117295 |
Serial |
5960 |
Permanent link to this record |
|
|
|
Author |
Sóti, V.; Jacquet, N.; Apers, S.; Richel, A.; Lenaerts, S.; Cornet, I. |
Title |
Monitoring the laccase reaction of vanillin and poplar hydrolysate |
Type |
A1 Journal article |
Year |
2016 |
Publication |
Journal of chemical technology and biotechnology |
Abbreviated Journal |
J Chem Technol Biot |
Volume |
91 |
Issue |
6 |
Pages |
1914-1922 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL); Biochemical Wastewater Valorization & Engineering (BioWaVE) |
Abstract |
BACKGROUND Laccase is an intensively researched enzyme for industrial use. Except for decolorisation measurements, HPLC analysis is the conventional method for monitoring the phenolic removal during laccase enzyme reaction. This paper reports an investigation of the continuous UV absorbance follow-up of the laccase reaction with steam pretreated poplar hydrolysate. RESULTS Vanillin was used as a model substrate and lignocellulose xylose rich fraction (XRF) as a biologically complex substrate for laccase detoxification. The reaction was followed by HPLC-UV as well as by UV spectrometric measurements. Results suggest that the reaction can be successfully monitored by measuring the change of UV absorbance at 280 nm, without previous compound separation. In case of XRF experiments the spectrophotometric follow-up is especially useful, as HPLC analysis takes a long time and provides less information than in case of single substrates. The method seems to be suitable for optimization and process control. CONCLUSION The obtained results can help to construct a fast, easy and straightforward monitoring system for laccase-phenolic substrate reactions. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000375768300040 |
Publication Date |
2015-07-29 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0268-2575; 1097-4660 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.135 |
Times cited |
3 |
Open Access |
|
Notes |
; This research is financed by the University of Antwerp (project number 15 FA100 002). ; |
Approved |
Most recent IF: 3.135 |
Call Number |
UA @ admin @ c:irua:127694 |
Serial |
5972 |
Permanent link to this record |
|
|
|
Author |
Sóti, V.; Lenaerts, S.; Cornet, I. |
Title |
Of enzyme use in cost-effective high solid simultaneous saccharification and fermentation processes |
Type |
A1 Journal article |
Year |
2018 |
Publication |
Journal of biotechnology |
Abbreviated Journal |
J Biotechnol |
Volume |
270 |
Issue |
270 |
Pages |
70-76 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL); Biochemical Wastewater Valorization & Engineering (BioWaVE) |
Abstract |
Enzyme cost is considered to be one of the most significant factors defining the final product price in lignocellulose hydrolysis and fermentation. Enzyme immobilization and recycling can be a tool to decrease costs. However, high solid loading is a key factor towards high product titers, and recovery of immobilized enzymes from this thick liquid is often overlooked. This paper aims to evaluate the economic feasibility of immobilized enzymes in simultaneous saccharification and fermentation (SSF) of lignocellulose biomass in general, as well as the recuperation of magnetic immobilized enzymes (m-CLEAs) during high solid loading in simultaneous saccharification, detoxification and fermentation processes (SSDF) of lignocellulose biomass. Enzyme prices were obtained from general cost estimations by Klein-Marcuschamer et al. [Klein-Marcuschamer et al. (2012) Biotechnol. Bioeng. 109, 10831087]. During enzyme cost analysis, the influence of inoculum recirculation as well as a shortened fermentation time was explored. Both resulted in 15% decrease of final enzyme product price. Enzyme recuperation was investigated experimentally and 99.5 m/m% of m-CLEAs was recovered from liquid medium in one step, while 88 m/m% could still be recycled from a thick liquid with high solid concentrations (SSF fermentation broth). A mathematical model was constructed to calculate the cost of immobilized and free enzyme utilization and showed that, with current process efficiencies and commercial enzyme prices, the cost reduction obtained by enzyme immobilization can reach around 60% compared to free enzyme utilization, while lower enzyme prices will result in a lower percentage of immobilization related savings, but overall enzyme costs will decrease significantly. These results are applied in a case study, estimating the viability of shifting from sugar to lignocellulose substrate for a 100 t lactic acid fermentation batch. It was concluded that it will only be economically feasible if the enzymes are produced at the most optimistic variable cost and either the activity of the immobilized catalyst or the recovery efficiency is further increased. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000427556400009 |
Publication Date |
2018-02-08 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0168-1656 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
2.599 |
Times cited |
6 |
Open Access |
|
Notes |
; This research is financed by the University of Antwerp [project number 15 FA100 002]. ; |
Approved |
Most recent IF: 2.599 |
Call Number |
UA @ admin @ c:irua:149006 |
Serial |
5974 |
Permanent link to this record |
|
|
|
Author |
Huyskens, C.; De Wever, H.; Fovet, Y.; Wegmann, U.; Diels, L.; Lenaerts, S. |
Title |
Screening of novel MBR fouling reducers : benchmarking with known fouling reducers and evaluation of their mechanism of action |
Type |
A1 Journal article |
Year |
2012 |
Publication |
Separation and purification technology |
Abbreviated Journal |
Sep Purif Technol |
Volume |
95 |
Issue |
|
Pages |
49-57 |
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
Abstract |
A novel fouling characterization method was applied for a first screening of two novel synthetic flocculants developed by BASF (BASF-1 and BASF-2) and benchmarking with six well-known products. Results showed that this MBR-VITO Fouling Measurement (VFM) was able to identify beneficial and adverse effects of different additives on the mixed liquor's reversible and irreversible fouling and, in combination with supporting mixed liquor analyses, allowed to identify the additive's main working mechanism. The first screening tests indicated that BASF-1 and BASF-2 reduced reversible and irreversible fouling to a similar extent as the known synthetic flocculants due to a charge neutralization mechanism, resulting in enhanced flocculation and SMP removal. Further testing at different additive concentrations provided a first indication of the optimal dosage and revealed a considerable risk of overdosing for BASF-2, rendering it less suited for fouling control. In contrast, such adverse effects were not observed for BASF-1. BASF-1 induced similar beneficial effects as the known MPE50 polymer at lower dosage and was therefore considered promising for application in MBRs. (C) 2012 Elsevier B.V. All rights reserved. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000307032100008 |
Publication Date |
2012-04-26 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1383-5866 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.359 |
Times cited |
24 |
Open Access |
|
Notes |
; The authors would like to thank K. Luyckx, J. Fret, L. Heylen, R. Muyshondt, H. Sterckx, J. Verheyden and J. Vande-Velden for technical assistance and V. Iversen for kindly supplying some of the commercial additives. Celine Huyskens is indebted to the Research Foundation-Flanders (FWO). The European Commission is acknowledged for financial support to Aquafit4use (FP7, Grant 211534). ; |
Approved |
Most recent IF: 3.359; 2012 IF: 2.894 |
Call Number |
UA @ admin @ c:irua:101903 |
Serial |
5990 |
Permanent link to this record |
|
|
|
Author |
Huyskens, C.; Lenaerts, S.; Brauns, E.; Diels, L.; de Wever, H. |
Title |
Study of (ir)reversible fouling in MBRs under various operating conditions using new on-line fouling sensor |
Type |
A1 Journal article |
Year |
2011 |
Publication |
Separation and purification technology |
Abbreviated Journal |
Sep Purif Technol |
Volume |
81 |
Issue |
2 |
Pages |
208-215 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
Abstract |
In this study, a new fouling sensor was validated under different conditions of hydraulic (HRT) and sludge retention time (SRT). The MBR-VFM (membrane bioreactor-VITO Fouling Measurement) allows the simultaneous determination of the physically reversible and irreversible fouling potential of a mixed liquor during a single crossflow filtration test. In accordance with the on-line filtration behavior, the measured reversible and irreversible fouling propensities differed significantly between MBRs operated at different combinations of HRT-SRT. Moreover, a significant negative correlation was found between the on-line permeability and the reversible and irreversible fouling propensity measured by the MBR-VFM. This corresponded to observations made on membrane recovery after physical or chemical cleaning actions. Higher reversible and irreversible fouling were observed at lower HRT, presumably as a consequence of increased concentrations of foulants present. The effect of SRT was much smaller and restricted to the reversible fouling component. Possible explanations for the increased fouling at prolonged SRT are the higher sludge and colloid concentration and the smaller floc size. It can be concluded that the MBR-VFM is a useful tool to monitor fluctuations in a mixed liquors (ir)reversible fouling potential and can contribute to a deeper understanding of the occurring fouling phenomena. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000296108500012 |
Publication Date |
2011-08-01 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1383-5866 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.359 |
Times cited |
15 |
Open Access |
|
Notes |
; ; |
Approved |
Most recent IF: 3.359; 2011 IF: 2.921 |
Call Number |
UA @ admin @ c:irua:93410 |
Serial |
5992 |
Permanent link to this record |
|
|
|
Author |
Van Wesenbeeck, K.; Hauchecorne, B.; Lenaerts, S. |
Title |
Study of positive and negative plasma catalytic oxidation of ethylene |
Type |
A1 Journal article |
Year |
2017 |
Publication |
Environmental technology |
Abbreviated Journal |
Environ Technol |
Volume |
38 |
Issue |
12 |
Pages |
1554-1561 |
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
Abstract |
The effect of introducing a photocatalytically active coating inside a plasma unit is investigated. This technique combines the advantages of high product selectivity from catalysis and the fast start-up from plasma technology. In this study, a preselected TiO2 coating is applied on the collector electrode of a DC corona discharge unit as non-thermal plasma reactor, in order to study the oxidation of ethylene. For both positive and negative polarities an enhanced mineralization is observed while the formation of by-products drastically decreases. The plasma catalytic unit gave the best results when using negative polarity at a voltage of 15kV. This shows the potential of plasma catalysis as indoor air purification technology. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000402018900010 |
Publication Date |
2016-10-03 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0959-3330 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
1.751 |
Times cited |
1 |
Open Access |
|
Notes |
; The authors wish to thank the University of Antwerp for supporting and funding this research. ; |
Approved |
Most recent IF: 1.751 |
Call Number |
UA @ admin @ c:irua:144351 |
Serial |
5993 |
Permanent link to this record |
|
|
|
Author |
Blommaerts, N.; Dingenen, F.; Middelkoop, V.; Savelkouls, J.; Goemans, M.; Tytgat, T.; Verbruggen, S.W.; Lenaerts, S. |
Title |
Ultrafast screening of commercial sorbent materials for VOC adsorption using real-time FTIR spectroscopy |
Type |
A1 Journal article |
Year |
2018 |
Publication |
Separation and purification technology |
Abbreviated Journal |
Sep Purif Technol |
Volume |
207 |
Issue |
207 |
Pages |
284-290 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
Abstract |
Recovery of valuable volatile organic compounds (VOCs) from waste streams is of great industrial importance. Adsorption on zeolites offers an economically and environmentally friendly alternative to conventional activated carbon. When evaluating the suitability of a given zeolite for a particular adsorption application, its adsorption capacity has to be determined. This is traditionally achieved using gas chromatography as an analysis tool, yielding only a few discrete sampling points that constitute the adsorption profile. Meanwhile, only low flow rates and low concentrations of volatile organics can be used, rendering the procedure troublesome and time consuming. Herein, we propose a tool for the fast screening of a large amount of zeolites using on-line and quasi real-time Fourier Transform Infrared Spectroscopy (FTIR). The technique was used to determine the adsorption capacity of three different commercial zeolites and two silica gels, for five industrially relevant VOCs: acetone; methanol; isohexane; isopentane; and toluene. A series of rapid measurements of the individual adsorption capacities were carried out to obtain a detailed overview of the versatility of the proposed method for the characterization of multi-component and multi-sorption bed systems. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000445987500032 |
Publication Date |
2018-06-27 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1383-5866 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.359 |
Times cited |
5 |
Open Access |
|
Notes |
; We would like to thank Vlaams Agenschap Innoveren & Ondernemen (VLAIO) for financial support. The authors would also like to thank Kureha GmbH, Germany for kindly supplying us with their BAC (R) (bead-shaped activated carbon) samples. ; |
Approved |
Most recent IF: 3.359 |
Call Number |
UA @ admin @ c:irua:154694 |
Serial |
6000 |
Permanent link to this record |
|
|
|
Author |
Hauchecorne, B.; Tytgat, T.; Terrens, D.; Vanpachtenbeke, F.; Lenaerts, S. |
Title |
Validation of a newly developed FTIR in situ reactor: real time study of photocatalytic degradation of nitric oxide |
Type |
A1 Journal article |
Year |
2010 |
Publication |
Infrared physics and technology |
Abbreviated Journal |
Infrared Phys Techn |
Volume |
53 |
Issue |
6 |
Pages |
469-473 |
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
Abstract |
For many years, photocatalysis has been proposed as one of the promising techniques to abate environmental pollutants. To improve these reactions it is vital to know the reaction mechanisms of the photocatalytic degradation. This new reactor will make it possible to study the catalytic surface at the moment the reactions occur. By the means of UV LED illumination there is no need of an external UV lamp and thus lowers the cost. The validation of this newly developed reactor is done by investigating the photocatalytic reaction mechanism of nitric oxide (NO) and comparing these findings with those already discussed in literature. From these results, it became clear that the newly developed FTIR in situ reactor allows real time study of photocatalytic degradations. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000285169400009 |
Publication Date |
2010-10-09 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1350-4495 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
1.713 |
Times cited |
12 |
Open Access |
|
Notes |
; ; |
Approved |
Most recent IF: 1.713; 2010 IF: 0.932 |
Call Number |
UA @ admin @ c:irua:84561 |
Serial |
6002 |
Permanent link to this record |
|
|
|
Author |
Van Eynde, E.; Lenaerts, B.; Tytgat, T.; Blust, R.; Lenaerts, S. |
Title |
Valorization of flue gas by combining photocatalytic gas pretreatment with microalgae production |
Type |
A1 Journal article |
Year |
2016 |
Publication |
Environmental science and technology |
Abbreviated Journal |
Environ Sci Technol |
Volume |
50 |
Issue |
5 |
Pages |
2538-2545 |
Keywords |
A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL) |
Abstract |
Utilization of flue gas for algae cultivation seems to be a promising route because flue gas from fossil-fuel combustion processes contains the high amounts of carbon (CO2) and nitrogen (NO) that are required for algae growth. NO is a poor nitrogen source for algae cultivation because of its low reactivity and solubility in water and its toxicity for algae at high concentrations. Here, we present a novel strategy to valorize NO from flue gas as feedstock for algae production by combining a photocatalytic gas pretreatment unit with a microalgal photobioreactor. The photocatalytic air pretreatment transforms NO gas into NO2 gas and thereby enhances the absorption of NO in the cultivation broth. The absorbed NOx will form NO2- and NO3- that can be used as a nitrogen source by algae. The effect of photocatalytic air pretreatment on the growth and biomass productivity of the algae Thalassiosira weissflogii in a semicontinuous system aerated with a model flue gas (1% CO2 and 50 ppm of NO) is investigated during a long-term experiment. The integrated system makes it possible to produce algae with NO from flue gas as the sole nitrogen source and reduces the NOx content in the exhaust gas by 84%. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000371371700048 |
Publication Date |
2016-02-03 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0013-936x; 1520-5851 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
6.198 |
Times cited |
6 |
Open Access |
|
Notes |
; ; |
Approved |
Most recent IF: 6.198 |
Call Number |
UA @ admin @ c:irua:132348 |
Serial |
6003 |
Permanent link to this record |
|
|
|
Author |
Thomassen, G.; Van Dael, M.; Van Passel, S. |
Title |
The potential of microalgae biorefineries in Belgium and India : an environmental techno-economic assessment |
Type |
A1 Journal article |
Year |
2018 |
Publication |
Bioresource Technology |
Abbreviated Journal |
Bioresource Technol |
Volume |
267 |
Issue |
267 |
Pages |
271-280 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM) |
Abstract |
This study performs an environmental techno-economic assessment (ETEA) for multiple microalgae biorefinery concepts at different locations, those being Belgium and India. The ETEA methodology, which integrates aspects of the TEA and LCA methodologies and provides a clear framework for an integrated assessment model, has been proposed and discussed. The scenario in India has a higher profitability with a NPV of (sic)40 million over a period of 10 years, while the environmental impact in Belgium is lower. The inclusion of a medium recycling step provides the best scenario from both perspectives. The crucial parameters for feasibility are the beta-caroteneprice and content, the upstream environmental impact of electricity and the maximum biomass concentration during cultivation. The identification of these parameters by the ETEA guides future technology developments and shortens the time-to-market for microalgal-based biorefineries. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000441876100034 |
Publication Date |
2018-07-10 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0960-8524 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles; WoS full record; WoS citing articles |
Impact Factor |
5.651 |
Times cited |
8 |
Open Access |
|
Notes |
; ; |
Approved |
Most recent IF: 5.651 |
Call Number |
UA @ admin @ c:irua:153599 |
Serial |
6270 |
Permanent link to this record |
|
|
|
Author |
Zarafshani, K.; Ghasemi, S.; Houshyar, E.; Ghanbari, R.; Van Passel, S.; Azadi, H. |
Title |
Canola adoption enhancement in Western Iran |
Type |
A1 Journal article |
Year |
2017 |
Publication |
Journal Of Agricultural Science And Technology |
Abbreviated Journal |
J Agr Sci Tech-Iran |
Volume |
19 |
Issue |
1 |
Pages |
47-58 |
Keywords |
A1 Journal article; Economics; Engineering Management (ENM) |
Abstract |
Canola production is an important alternative for agricultural policy-makers in Iran to reduce dependency on the imported vegetable oils. Nevertheless, the canola planted area is only increasing at a slow pace, indicating a low willingness-to-accept of farmers. The general aim of this study was to determine the factors influencing the canola adoption in the Kermanshah Province in Western Iran. Employing stratified random sampling method, 106 farmers from each adopter and non-adopter group were selected. Helping to reach a suitable extensional program, two main categories of variables were defined; i.e. farmers personal characteristics and extension parameters. The analysis of farmers personal characteristics variables revealed that the adopters had larger farms and were younger. The results also show that 80% of the adopters were highly to very highly willing to cultivate canola. Furthermore, a logistic regression model estimated the influence of extensional parameters variables on the canola adoption. According to the regression model, the most effective factors are contact with extension agents and participating in extension classes. As a conclusion, it is suggested that the focus of extension services should be to reduce the distance to agricultural service centers in combination with more contact with extension agents and classes. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
|
Publication Date |
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1680-7073 |
ISBN |
|
Additional Links |
UA library record |
Impact Factor |
0.813 |
Times cited |
|
Open Access |
|
Notes |
|
Approved |
Most recent IF: 0.813 |
Call Number |
UA @ admin @ c:irua:140684 |
Serial |
6164 |
Permanent link to this record |
|
|
|
Author |
Sun, S.R.; Wang, H.X.; Bogaerts, A. |
Title |
Chemistry reduction of complex CO2chemical kinetics: application to a gliding arc plasma |
Type |
A1 Journal article |
Year |
2020 |
Publication |
Plasma Sources Science & Technology |
Abbreviated Journal |
Plasma Sources Sci T |
Volume |
29 |
Issue |
2 |
Pages |
025012 |
Keywords |
A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
Abstract |
A gliding arc (GA) plasma has great potential for CO2 conversion into value-added chemicals, because of its high energy efficiency. To improve the application, a 2D/3D fluid model is needed to investigate the CO2 conversion mechanisms in the actual discharge geometry. Therefore, the complex CO2 chemical kinetics description must be reduced due to the huge computational cost associated with 2D/3D models. This paper presents a chemistry reduction method for CO2 plasmas, based on the so-called directed relation graph method. Depending on the defined threshold values, some marginal species are identified. By means of a sensitivity analysis, we can further reduce the chemistry set by removing one by one the marginal species. Based on the socalled flux-sensitivity coupling, we obtain a reduced CO2 kinetics model, consisting of 36 or 15 species (depending on whether the 21 asymmetric mode vibrational states of CO2 are explicitly included or lumped into one group), which is applied to a GA discharge. The results are compared with those predicted with the full chemistry set, and very good agreement is reached. Moreover, the range of validity of the reduced CO2 chemistry set is checked, telling us that this reduced set is suitable for low power GA discharges. Finally, the time and spatial evolution of the CO2 plasma characteristics are presented, based on a 2D model with the reduced kinetics. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000525600600001 |
Publication Date |
2020-02-11 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1361-6595 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.8 |
Times cited |
|
Open Access |
|
Notes |
We acknowledge financial support from the Fund for Scientific Research Flanders (FWO; Grant No. G.0383.16 N). The calculations were performed using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UAntwerpen), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UAntwerpen. This work was also supported by the National Natural Science Foundation of China. (Grant Nos. 11735004, 11575019). SR Sun thanks the financial support from the National Postdoctoral Program for Innovative Talents (BX20180029). |
Approved |
Most recent IF: 3.8; 2020 IF: 3.302 |
Call Number |
PLASMANT @ plasmant @c:irua:167135 |
Serial |
6338 |
Permanent link to this record |
|
|
|
Author |
Spanoghe, J.; Grunert, O.; Wambacq, E.; Sakarika, M.; Papini, G.; Alloul, A.; Spiller, M.; Derycke, V.; Stragier, L.; Verstraete, H.; Fauconnier, K.; Verstraete, W.; Haesaert, G.; Vlaeminck, S.E. |
Title |
Storage, fertilization and cost properties highlight the potential of dried microbial biomass as organic fertilizer |
Type |
A1 Journal article |
Year |
2020 |
Publication |
Microbial biotechnology |
Abbreviated Journal |
Microb. Biotechnol. |
Volume |
|
Issue |
|
Pages |
1-13 |
Keywords |
A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL) |
Abstract |
The transition to sustainable agriculture and horticulture is a societal challenge of global importance. Fertilization with a minimum impact on the environment can facilitate this. Organic fertilizers can play an important role, given their typical release pattern and production through resource recovery. Microbial fertilizers (MFs) constitute an emerging class of organic fertilizers and consist of dried microbial biomass, for instance produced on effluents from the food and beverage industry. In this study, three groups of organisms were tested as MFs: a high-rate consortium aerobic bacteria (CAB), the microalga Arthrospira platensis (‘Spirulina’) and a purple non-sulfur bacterium (PNSB) Rhodobacter sp. During storage as dry products, the MFs showed light hygroscopic activity, but the mineral and organic fractions remained stable over a storage period of 91 days. For biological tests, a reference organic fertilizer (ROF) was used as positive control, and a commercial organic growing medium (GM) as substrate. The mineralization patterns without and with plants were similar for all MFs and ROF, with more than 70% of the organic nitrogen mineralized in 77 days. In a first fertilization trial with parsley, all MFs showed equal performance compared to ROF, and the plant fresh weight was even higher with CAB fertilization. CAB was subsequently used in a follow-up trial with petunia and resulted in elevated plant height, comparable chlorophyll content and a higher amount of flowers compared to ROF. Finally, a cost estimation for packed GM with supplemented fertilizer indicated that CAB and a blend of CAB/PNSB (85%/15%) were most cost competitive, with an increase of 6% and 7% in cost compared to ROF. In conclusion, as biobased fertilizers, MFs have the potential to contribute to sustainable plant nutrition, performing as good as a commercially available organic fertilizer, and to a circular economy. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000563539700001 |
Publication Date |
2020-03-16 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1751-7915 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
5.7 |
Times cited |
|
Open Access |
|
Notes |
The authors would like to kindly acknowledge (i) the MIP i‐Cleantech Flanders (Milieu‐innovatieplatform; Environment innovation platform) project Microbial Nutrients on Demand (MicroNOD) for financial support, (ii) the DOCPRO4 project ‘PurpleTech’, funded by the BOF (Bijzonder onderzoeksfonds; Special research fund) from the University of Antwerp for financially supporting J.S., (iii) all MicroNOD partners, including the University of Antwerp, Ghent University, AgrAqua, Greenyard Horticulture and Avecom; and (iv) all steering committee members, including Greenyard Frozen, Agristo, AVBS, Vlakwa, het Innovatiesteunpunt, VCM and OVAM. |
Approved |
Most recent IF: 5.7; 2020 IF: NA |
Call Number |
DuEL @ duel @c:irua:167595 |
Serial |
6357 |
Permanent link to this record |
|
|
|
Author |
van ‘t Veer, K.; Reniers, F.; Bogaerts, A. |
Title |
Zero-dimensional modeling of unpacked and packed bed dielectric barrier discharges: the role of vibrational kinetics in ammonia synthesis |
Type |
A1 Journal article |
Year |
2020 |
Publication |
Plasma Sources Science & Technology |
Abbreviated Journal |
Plasma Sources Sci T |
Volume |
29 |
Issue |
4 |
Pages |
045020 |
Keywords |
A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
Abstract |
We present a zero-dimensional plasma kinetics model, including both surface and gas phase kinetics, to determine the role of vibrationally excited states in plasma-catalytic ammonia synthesis. We defined a new method to systematically capture the conditions of dielectric barrier discharges (DBDs), including those found in packed bed DBDs. We included the spatial and temporal nature of such discharges by special consideration of the number of micro-discharges in the model. We introduce a parameter that assigns only a part of the plasma power to the microdischarges, to scale the model conditions from filamentary to uniform plasma. Because of the spatial and temporal behaviour of the micro-discharges, not all micro-discharges occurring in the plasma reactor during a certain gas residence time are affecting the molecules. The fraction of power considered in the model ranges from 0.005 %, for filamentary plasma, to 100 %, for uniform plasma. If vibrational excitation is included in the plasma chemistry, these different conditions, however, yield an ammonia density that is only varying within one order of magnitude. At only 0.05 % of the power put into the uniform plasma component, a model neglecting vibrational excitation clearly does not result in adequate amounts of ammonia. Thus, our new model, which accounts for the concept in which not all the power is deposited by the micro-discharges, but some part may also be distributed in between them, suggests that vibrational kinetic processes are really important in (packed bed) DBDs. Indeed, vibrational excitation takes place in both the uniform plasma between the micro-discharges and in the strong micro-discharges, and is responsible for an increased N2 dissociation rate. This is shown here for plasma-catalytic ammonia synthesis, but might also be valid for other gas conversion applications. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000570241500001 |
Publication Date |
2020-04-09 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1361-6595 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.8 |
Times cited |
|
Open Access |
|
Notes |
This research was supported by the Excellence of Science FWO-FNRS project (FWO grant ID GoF9618n, EOS ID 30505023). The calculations were performed using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen (UAntwerpen), a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the UAntwerpen. The authors would also like to thank Dr. Fatme Jardali for the discussions on plasma kinetic modelling and Dr. Jungmi Hong and Dr. Anthony B. Murphy for their aid in the calculation of the diffusion coefficients. |
Approved |
Most recent IF: 3.8; 2020 IF: 3.302 |
Call Number |
PLASMANT @ plasmant @c:irua:168097 |
Serial |
6359 |
Permanent link to this record |
|
|
|
Author |
Zhang, H.; Zhang, H.; Trenchev, G.; Li, X.; Wu, Y.; Bogaerts, A. |
Title |
Multi-dimensional modelling of a magnetically stabilized gliding arc plasma in argon and CO2 |
Type |
A1 Journal article |
Year |
2020 |
Publication |
Plasma Sources Science & Technology |
Abbreviated Journal |
Plasma Sources Sci T |
Volume |
29 |
Issue |
4 |
Pages |
045019 |
Keywords |
A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
Abstract |
This study focuses on a magnetically stabilized gliding arc (MGA) plasma. Two fully coupled flow-plasma models (in 3D and 2D) are presented. The 3D model is applied to compare the arc dynamics of the MGA with a traditional gas-driven gliding arc. The 2D model is used for a detailed parametric study on the effect of the external magnetic field. The results show that the relative velocity between the plasma and feed gas is generated due to the Lorentz force, which can increase the plasma-treated gas fraction. The magnetic field also helps to decrease the gas temperature by enhancing heat transfer and to increase the electron number density. This work shows the potential of an external magnetic field to control the gliding arc behavior, for enhanced gas conversion at low gas flow rates. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000570241800001 |
Publication Date |
2020-04-09 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1361-6595 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.8 |
Times cited |
|
Open Access |
|
Notes |
Fonds Wetenschappelijk Onderzoek, G.0383.16N ; National Natural Science Foundation of China, 51706204 51707144 ; State Key Laboratory of Electrical Insulation and Power Equipment, EIPE19302 ; The authors acknowledge financial support from the Fund for Scientific Research—Flanders (FWO; Grant G.0383.16 N), National Natural Science Foundation of China under Grant Nos. 51706204, 51707144, and State Key Laboratory of Electrical Insulation and Power Equipment (EIPE19302). The calculations were performed using the Turing HPC infrastructure at the CalcUA core facility of Universiteit Antwerpen, a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (Department EWI), and Universiteit Antwerpen. Finally, Hantian Zhang acknowledges financial support from the China Scholarship Council. |
Approved |
Most recent IF: 3.8; 2020 IF: 3.302 |
Call Number |
PLASMANT @ plasmant @c:irua:169218 |
Serial |
6360 |
Permanent link to this record |
|
|
|
Author |
Lumbeeck, G.; Delvaux, A.; Idrissi, H.; Proost, J.; Schryvers, D. |
Title |
Analysis of internal stress build-up during deposition of nanocrystalline Ni thin films using transmission electron microscopy |
Type |
A1 Journal article |
Year |
2020 |
Publication |
Thin solid films : an international journal on the science and technology of thin and thick films |
Abbreviated Journal |
Thin Solid Films |
Volume |
707 |
Issue |
|
Pages |
138076 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
Ni thin films sputter-deposited at room temperature with varying Ar pressures were investigated with automated crystal orientation mapping in a transmission electron microscope to uncover the mechanisms controlling the internal stress build-up recorded in-situ during deposition. Large grains were found to induce behaviour similar to a stress-free nucleation layer. The measurements of grain size in most of the Ni thin films are in agreement with the island coalescence model. Low internal stress was observed at low Ar pressure and was explained by the presence of large grains. Relaxation of high internal stress was also noticed at the highest Ar pressure, which was attributed to a decrease of Σ3 twin boundary density due to a low deposition rate. The results provide insightful information to better understand the relationship between structural boundaries and the evolution of internal stress upon deposition of thin films. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000539312200011 |
Publication Date |
2020-05-12 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
|
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
|
Times cited |
|
Open Access |
OpenAccess |
Notes |
This work was supported by the Hercules Foundation [Grant No. AUHA13009], the Flemish Research Fund (FWO) [Grant No. G.0365.15N], and the Flemish Strategic Initiative for Materials (SIM) under the project InterPoCo. Thin film deposition has been realised as part of the WallonHY project, funded by the Public Service of Wallonia – Department of Energy and Sustainable Building. H. Idrissi is mandated by the Belgian National Fund for Scientific Research (FSR-FNRS). |
Approved |
Most recent IF: NA |
Call Number |
EMAT @ emat @c:irua:169708 |
Serial |
6370 |
Permanent link to this record |
|
|
|
Author |
Celentano, G.; Rizzo, F.; Augieri, A.; Mancini, A.; Pinto, V.; Rufoloni, A.; Vannozzi, A.; MacManus-Driscoll, J.L.; Feighan, J.; Kursumovic, A.; Meledin, A.; Mayer, J.; Van Tendeloo, G. |
Title |
YBa2Cu3O7−xfilms with Ba2Y(Nb,Ta)O6nanoinclusions for high-field applications |
Type |
A1 Journal article |
Year |
2020 |
Publication |
Superconductor Science & Technology |
Abbreviated Journal |
Supercond Sci Tech |
Volume |
33 |
Issue |
4 |
Pages |
044010 |
Keywords |
A1 Journal article; Electron microscopy for materials research (EMAT) |
Abstract |
The structural and transport properties of YBa2Cu3O7−x films grown by pulsed laser deposition with mixed 2.5 mol% Ba2YTaO6 (BYTO) and 2.5 mol% Ba2YNbO6 (BYNO) double-perovskite secondary phases are investigated in an extended film growth rate, R = 0.02–1.8 nm s−1. The effect of R on the film microstructure analyzed by TEM techniques shows an evolution from sparse and straight to denser, thinner and splayed continuous columns, with mixed BYNO + BYTO (BYNTO) composition, as R increases from 0.02 nm s−1 to 1.2 nm s−1. This microstructure results in very efficient flux pinning at 77 K, leading to a remarkable improvement in the critical current density (J c) behaviour, with the maximum pinning force density F p(Max) = 13.5 GN m−3 and the irreversibility field in excess of 11 T. In this range, the magnetic field values at which the F p is maximized varies from 1 T to 5 T, being related to the BYNTO columnar density. The film deposited when R = 0.3 nm s−1 exhibits the best performances over the whole temperature and magnetic field ranges, achieving F p(Max) = 900 GN m−3 at 10 K and 12 T. At higher rates, R > 1.2 nm s−1, BYNTO columns show a meandering nature and are prone to form short nanorods. In addition, in the YBCO film matrix a more disordered structure with a high density of short stacking faults is observed. From the analysis of the F p(H, T) curves it emerges that in films deposited at the high R limit, the vortex pinning is no longer dominated by BYNTO columnar defects, but by a new mechanism showing the typical temperature scaling law. Even though this microstructure produces a limited improvement at 77 K, it exhibits a strong J c improvement at lower temperature with F p = 700 GN m−3 at 10 K, 12 T and 900 GN m−3 at 4.2 K, 18 T. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000525650500001 |
Publication Date |
2020-04-01 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
0953-2048 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.6 |
Times cited |
|
Open Access |
OpenAccess |
Notes |
This work was partially financially supported by EUROTAPES, a collaborative project funded by the European Commission’s Seventh Framework Program (FP7/2007–2013) under Grant Agreement No. 280432. This work has been partially carried out within the framework of the EUROfusion Consortium and has received funding from the Euratom programme 2014-2018 and 2019-2020 under grant agreement N° 633053. The views and opinions expressed herein do not necessarily reflect those of the European Commission. This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 823717 – ESTEEM3 (Nano-engineered YBCO Superconducting Tapes for High Field Applications, NESTApp). G. C. acknowledges the support of Michele De Angelis for XRD measurements and calculations. |
Approved |
Most recent IF: 3.6; 2020 IF: 2.878 |
Call Number |
UA @ lucian @c:irua:168582 |
Serial |
6394 |
Permanent link to this record |
|
|
|
Author |
Verheyen, C.; Silva, T.; Guerra, V.; Bogaerts, A. |
Title |
The effect of H2O on the vibrational populations of CO2in a CO2/H2O microwave plasma: a kinetic modelling investigation |
Type |
A1 Journal article |
Year |
2020 |
Publication |
Plasma Sources Science & Technology |
Abbreviated Journal |
Plasma Sources Sci T |
Volume |
29 |
Issue |
9 |
Pages |
095009 |
Keywords |
A1 Journal article; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
Abstract |
Plasma has been studied for several years to convert CO2 into value-added products. If CO2 could be converted in the presence of H2O as a cheap H-source for making syngas and oxygenates, it would mimic natural photosynthesis. However, CO2/H2O plasmas have not yet been extensively studied, not by experiments, and certainly not computationally. Therefore, we present here a kinetic modelling study to obtain a greater understanding of the vibrational kinetics of a CO2/H2O microwave plasma. For this purpose, we first created an electron impact cross section set for H2O, using a swarm-derived method. We added the new cross section set and CO2/H2O-related chemistry to a pure CO2 model. While it was expected that H2O addition mainly causes quenching of the CO2 asymmetric mode vibrational levels due to the additional CO2/H2O vibrational-translational relaxation, our model shows that the modifications in the vibrational kinetics are mainly induced by the strong electron dissociative attachment to H2O molecules, causing a reduction in electron density, and the corresponding changes in the input of energy into the CO2 vibrational levels by electron impact processes. |
Address |
|
Corporate Author |
|
Thesis |
|
Publisher |
|
Place of Publication |
|
Editor |
|
Language |
|
Wos |
000570601300001 |
Publication Date |
2020-09-16 |
Series Editor |
|
Series Title |
|
Abbreviated Series Title ![sorted by Abbreviated Series Title field, ascending order (up)](img/sort_asc.gif) |
|
Series Volume |
|
Series Issue |
|
Edition |
|
ISSN |
1361-6595 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
Impact Factor |
3.8 |
Times cited |
|
Open Access |
|
Notes |
Fonds Wetenschappelijk Onderzoek, 1184820N ; Fundação para a Ciência e a Tecnologia, under projects UIDB/50010/2020 and ; This research was supported by FWO–PhD fellowshipaspirant, Grant 1184820N. VG and TS were partially supported by the Portuguese FCT, under projects UIDB/50010/2020 and UIDP/50010/2020 |
Approved |
Most recent IF: 3.8; 2020 IF: 3.302 |
Call Number |
PLASMANT @ plasmant @c:irua:172011 |
Serial |
6433 |
Permanent link to this record |