Abstract: The irreversible release of the lattice oxygen in layered cathodes is one of the major degradation mechanisms of lithium ion batteries, which accounts for a number of battery failures including the voltage/capacity fade, loss of cation ions and detachment of the primary particles, etc. Oxygen release is generally attributed to the stepwise thermodynamic controlled phase transitions from the layered to spinel and rock salt phases. Here, we report a strong kinetic effect from the mobility of cation ions, whose migration barrier can be significantly modulated by the phase epitaxy at the degrading interface. It ends up with a clear oxygen release heterogeneity and completely different reaction pathways between the thin and thick areas, as well as the interparticle valence boundaries, both of which widely exist in the mainstream cathode design with the secondary agglomerates. This work unveils the origin of the heterogenous oxygen release in the layered cathodes. It also sheds light on the rational design of cathode materials with enhanced oxygen stability by suppressing the cation migration.

Abstract: Transmission electron microscopy (TEM) is an ideal tool to investigate nanomaterials. The information from TEM experiments allows us to link the structure and composition of nanomaterials to their intrinsic physical properties. However, despite the significant evolution of the TEM field during the last two decades, major progress is still possible through the development of optimal TEM techniques and supports. The results presented in this thesis focus on the optimization of sample supports and their application. Among the different options, graphene has previously been reported as useful sample support for electron microscopy due to its unparalleled properties, for example, it is the thinnest known support and provides a protective effect to the sample under investigation. Unfortunately, commercial graphene grids show poor quality, in terms of intactness and cleanness, inhibiting their wide application within the field. Therefore, this thesis focuses on the application of optimized graphene TEM grids, obtained by transferring high quality graphene using an advanced procedure. This improvement on the transfer has enabled the visualization of materials with low contrast and high sensitivity towards the electron beam, such as surface ligands capping gold nanoparticles or metal halide perovskites. Furthermore, the implemented protocol is not only of interest for conventional TEM grids but also a major benefit for in situ TEM studies, where the sample is investigated in real time under certain stimuli. Hence, the same graphene transfer technology can be also applied to advanced in situ MEMS holders dedicated for both heating and gas experiments, where the thickness and insulating nature of the silicon nitride (Si3N4) support may hamper some applications. By engineering periodic arrays of holes in their Si3N4 membrane by focused ion beam, onto which the graphene is transferred, it has been possible to get proof-of-concept 3D in situ investigations of heat-induced morphological and compositional transformations of complex nanosystems. As an example, it has enabled the investigation of the possible phase-transition of metal halide perovskites upon heating using 2D and 3D structural characterization. Moreover, it has allowed the study of in situ three-dimensional nanoparticle dynamics during gas phase catalysis as well as the first steps that would lead towards the design and creation of the first Graphene Gas Cell. Consequently, implementation of the advanced graphene transfer technology described in this thesis is envisaged to impact a broad range of future experiments.

Abstract: The strong correlated oxide systems attract a lot of attentions of scientists recently, the coexistence and interplay between various degrees of freedom, such as charge, spin and orbital, has been demonstrated to induce some fancy physical properties and phenomenon, including metal-insulator transition, high temperature superconductivity, colossal magnetoresistance. As a part of the strong correlated oxide systems, the ferroelectrics is abundant in both physical properties and application. First, if the electric dipole continuously rotating around a stable core then a topological structure is produced. If people could manipulate the topological structure and simultaneously observe the structure evolution, with external field applied on the topological structure, then it is very likely for such kind of ferroelectrics to be the next generation of storage, for it is reported to need low power input and produce high density of storage. In the other hand, in solids, charge polarity can one-to-one correspond to spin polarity phenomenologically, such as ferroelectricity and ferromagnetism, antiferroelectricity and antiferromagnetism, but ferrielectricity and ferrimagnetism kept telling a disparate story in microscopic level. The claimed “ferrielectrics” in existing research is equivalent to ferroelectric ones, thus the findings of such a real irreducible solids would complete the last piece of the ferroelectrics family. While solving the above two questions remain challengeable: the size of topological structure is small (typically below 10 nm), general characterization methods are insufficient for such high demand on space resolution, not to mention manipulating and observing its dynamic behavior at an atomic level. Here, employing the spherical aberration corrected electron microscope, we applied external field (heating and bias) on ferroelectrics. Combined with high-end characterization methods including the high-angle annular dark field (HAADF-STEM) image, Electron Energy Loss Spectroscopy (EELS) and integrated differential phase contrast (iDPC), the dynamic evolution of ferroelectrics are observed and analyzed. The main findings of this paper could be concluded as listed here: (1) PbTiO3(001)// SrTiO3(001) is grown on DyScO3 and SrRuO3 by pusled laser deposition, the atomical EDS mapping results reveal that the interface between PTO and STO is atomically sharp. Increasing the thickness of PTO from 1 uc to 21 uc, the topological structure wihtin PTO layer would transform from a/c domain to wave, vortex and finally flux closure domain. The geometric phase analysis results (GPA) reveal that above topological structures are corresponding to various strain. (2) Combined with in-situ biasing holder, the electric bias was applied on polar vortex, and it evolved from vortex (0 V) to polar wave (2 V) and finally polar down (5 V). EELS analysis was performed and we find that negative charge is gathered at vortex core, which turns the Ti4+ to Ti3+ there. The oxygen vacancy at negative polarization surface and the negative charge at the positive polarization surface realized the polarization screening of polar down domain. (3) Through the atomic inspection and analysis on lattice structure of BaFe2Se3, the near ladders within single unit are found to be different in degree of tetramerization, thus leading to a residual polarization along the a-axis. The further in-situ heating and biasing experiment was conducted on BaFe2Se3, and the strong and weak ladders are proved to be independent for their behavior under external field. This findings distinguishes ferrielectrics from ferroelectrics in solids.

Abstract: Currently, a large variety of materials are studied by transmission electron microscopy (TEM) as it offers the possibility to perform structural and elemental analysis at a local scale. Relatively recent advances in aberration correctors and electron sources allow the instrument to achieve atomic resolution. Along with these advances, a state-of-the-art technology has been reached in TEM. However, the instrument is far from being perfect and imperfections or external sources can make the interpretation of information troublesome. Environmental factors such as acoustic and mechanical vibrations, temperature fluctuations, etc., can induce sample drift and create image distortions. These distortions are enhanced in scanning operation because of the serial acquisition of the information, which are more apparent at atomic resolution as small field of views are imaged. In addition, scanning distortions are induced due to the finite time response of the scan coils. These types of distortions would reduce precision in atomic-scale strain analysis, for instance, in semiconductors. Most of the efforts to correct these distortions are focused on data processing techniques post-acquisition. Another limitation in TEM is beam damage effects. Beam damage arises because of the energy transferred to the sample in electron-sample interactions. In scanning TEM, at atomic resolution, the increased electron charge density (electron dose) carried on a sub-Å size electron probe may aggravate beam damage effects. Soft materials such as zeolites, organic, biological materials, etc., can be destroyed under irradiation limiting the amount of information that can be acquired. Current efforts to circumvent beam damage are mostly based on low electron dose acquisitions and data processing methods to maximize the signal at low dose conditions. In this thesis, a different approach is given to address drift and scanning distortions, as well as beam damage effects. Novel scan strategies are proposed for that purpose, which are shown to substantially overcome these issues compared to the standard scan method in TEM.

Abstract: Nanomaterialen kunnen uiterst interessante eigenschappen vertonen voor een verscheidenheid aan veelbelovende toepassingen, gaande van zonnecrème tot batterijen voor elektrische auto’s. Een nanometer is een miljard keer kleiner dan een meter. Op deze schaal kunnen de materiaaleigenschappen volledig verschillen van bulkmaterialen op grotere schaal. Bovendien hangen de eigenschappen van nanomaterialen sterk af van hun exacte grootte en vorm. Kleine verschillen in de posities van de atomen, in de grootte-orde van een picometer (nog eens duizend maal kleiner dan een nanometer), kunnen de fysische eigenschappen al drastisch beïnvloeden. Daarom is een betrouwbare kwantificering van de atomaire structuur van kritisch belang om de evolutie naar materiaalontwerp mogelijk te maken en inzicht te verwerven in de relatie tussen de fysische eigenschappen en de structuur van nanomaterialen. Daarnaast kan de atomaire structuur van nanomaterialen ook veranderen in de loop van de tijd ten gevolge van verschillende fysische processen. Het onderzoek dat in deze thesis gepresenteerd wordt, maakt het mogelijk om de dynamische structuurveranderingen van nanomaterialen betrouwbaar te kwantificeren op atomaire schaal door gebruik te maken van raster transmissie elektronenmicroscopie (STEM). Ik heb dit gerealiseerd door methodes te ontwikkelen waarmee ik het aantal atomen “achter elkaar” kan tellen in elke atoomkolom van een nanomateriaal, en dit op basis van beelden opgenomen met een elektronenmicroscoop. Een belangrijk verschil met telmethodes voor de analyse van een enkel beeld is het schatten van de kans dat een atoomkolom atomen zal verliezen of bijkrijgen van het ene naar het andere beeld in de tijdreeks. Deze kwantitatieve methode kan het ontrafelen van de tijdsafhankelijke structuur-eigenschappen relatie van een nanomateriaal mogelijk maken, wat uiteindelijk kan leiden tot efficiënter design en productie van nanomaterialen voor innovatieve toepassingen.

Abstract: Socially responsible investments can be defined as an investment process that integrates ethical values and environmental protection, improving social conditions, and good governance into a traditional investment decision. This integration is mainly a consequence of the growing importance that investors give to environmental, social, and governance (ESG) criteria, resulting in more sustainable development. Also, in the real estate sector, increased attention is being paid to the contributions made to integrate economic, environmental, and social factors into decisions. The ESG framework looks closely at how companies are managed, and the impact related to their market value. The factors for investors’ focus are summarized as environmental, social, and governance. The term ESG was coined in a 2004 United Nations (UN) report titled “Who Cares Wins,” aimed at raising awareness regarding the importance of environmental, social, and corporate governance issues in financial markets. The ESG criteria’s specific purpose is to guide investors in recognizing sustainable investments without evaluating how sustainable the asset is or the investment value represented by sustainability. It is essential to underline that ESG does not take specific economic interests into account. The rationale behind this apparent gap is that investors investigate the economic aspects before investing. However, by not explicitly linking ESG and economic criteria, attractive investments are often misjudged and not implemented. For example, investments that only show their value in the longer term or indirectly influence value by achieving a higher retention rate among incumbent tenants, reducing or eliminating friction costs. A product–service system (PSS) refers to a market proposition (business model) that builds on a product’s traditional functionality by incorporating additional services. Although services are already offered, the PSS function is to link the service to a product. The service thereby supports the operation of the product and generates additional benefits. It encompasses the integrated solutions of products and services to satisfy customers' needs and generate maximum value. According to Sutanto et al., a PSS is designed to focus on sustainability characterized in three dimensions. 1. The economic dimension 2. The environmental dimension 3. The social dimension When discussing sustainability in this thesis, we use the criteria listed above related to socially responsible investments. The link between PSS and ESG is that a PSS focuses on creating a sustainable system, and ESG makes sustainability more visible to investors. Therefore, when PSS are recognized and implemented in buildings, they must be evaluated using ESG analysis methods. Product-Service Systems (PSS) try to find a way to offer services on top of a product. The product is essentially secondary to the result that is delivered from the services. For example, the modem (product) that a cable company provides will be of secondary importance to the connectivity (service). Alternatively, it will be less critical how heat is made (product) than the intended set point is achieved in the building. PSSs transform the supply of products into services. In doing so, the responsibility shifts from delivering a product (once only) to continuous service delivery. Therefore, it is in the best interest of the service provider to deliver the outcome of the service as efficiently (read: lowest cost) as possible. A direct consequence of this is that the service provider will want to use the product as efficiently as possible and as long as possible to reduce his costs. Therefore, the supplier will also want to recover and maximize the reuse of his product based on the same rationale. A positive impact on the environment and the used raw materials is thus to be expected. The whole process of servitization (transforming products into services) in real estate will positively impact the Economic, Environmental and Social factors. Therefore, demonstrating this proposition is the main objective of this thesis. Smart PSS is the same idea as Product-Service systems but in which the digitization of the services plays a key role. It will be shown that by digitizing services, a broader range can be offered. It will be demonstrated that products that provide services at the building level can, through their interconnectedness, also provide services to external systems (e.g. electricity grid, urban planning, mobility, ...). At the same time, digitizing the products and services will also underpin trust in the systems and allow for proper remuneration. In this PhD, different standard systems in a building, such as the reservation system, the water heater, or the fire detection system, are equipped with additional services. A PSS is often specifically designed to focus on economic, social, and environmental dimensions. These dimensions correspond to the investor’s examination as part of the ESG analysis before investing. As the PSS is often specifically designed to integrate sustainability, there is a close link between the sustainability performance of the PSS and the ESG criteria evaluated by the investor. Throughout the work, the owner is considered to be the user of the building. It is not the case that only an owner-user can generate cash flow. In essence, if they have sufficient rights to the underlying product, any building user can activate services that generate cash flow. In today's market, it is logical that this is viewed in the owner-user context as they will usually choose the products to be installed in larger technical installations. They may have previously used a PSS or choose to move to one. However, a building’s tenant could choose to lease out their meeting rooms if they are not contractually prohibited from doing so since, in practice, contracts have begun to prohibit certain services. For example, rental contracts that actively prohibit renting out a property through platforms such as Airbnb. Thus, the user’s function could potentially impact how the PSS is designed. This work does not explicitly explore the impact of this aspect. The owner-user is assumed throughout this manuscript. The second chapter describes the state of affairs concerning PSSs in a broad framework evolving towards focusing on the real estate sector. After which, in the second chapter, ESG and the link to real estate and how smart real estate (smart buildings) is missing from this evaluation are discussed in more detail. Chapter 3 shows from a fire alarm system, which was extended with an evacuation support system, the usefulness, and the risk of data. Further work was done to demonstrate the added value in terms of Economic, Environmental and Social factors of standard installations in buildings. In Chapter 4, a simple sanitary hot water boiler is extended with a service that allows controlling this boiler according to the status of the electricity grid (surplus or shortage of energy). The supply and demand of energy on the power grid must be equal at all times. By equipping a classic water heater (product) with additional intelligence (service), it becomes possible to adjust the energy use to the grid's needs. The grid operators are prepared to pay for this. This payment can be linked to different energy markets (long term market, spot market, ...). This study looked at the fee that would have to be paid when the adjustment of the energy use can be made instantaneously so that the fee must be settled according to the prices on the imbalance market. In chapter 5, we look at the impact of the service to rent out free spaces as co-working places on a broad market (external to the building), compared to a regular reservation system. By renting out unused workplaces on a broad market, the utilization of the existing patrimony will be higher. The demand for new square meters with the same function will decrease as the supply-demand curve changes, and so will the price. This makes it less interesting to build new buildings. Less construction of new buildings will result in fewer resources being used, which will positively affect the environment. In addition, fewer new buildings with an office function will leave more space for buildings with another function. Also, the city's infrastructure will be less burdened (roads, sewerage, electricity grid,...). In The Hague, the decreasing need for new square meters of office buildings can lead to more space for affordable housing, for which the city has a great need. Chapter 6 will frame the valuation of service as a real options method that gives an impetus to a general valuation methodology to value the flexibility that Smart PSS inherently has. Finally, this thesis demonstrates that (smart) PSSs impact real estate profitability, while positively influencing environmental and social factors. Further research and the limitations of the studies conducted are documented. This PhD concludes that Product-Service systems should break the silos between different stakeholders, resulting in a lower total cost of ownership of buildings in the longer term. This can only be achieved if the valuation of Product-Service systems is done correctly and is recognized by every stakeholder in the real estate process.

Abstract: Landfill mining refers to the re-circulation of resources from the previously deposited wastes–integrating resource recovery with traditional site remediation. Several resources that can be recovered include scrap metals, combustibles, and inert materials. In addition, land can be recovered or landfill void space can be liberated for future wastes. At present, landfill mining is still an emerging concept with few project implementations. Consequently, the assessments of its economic and climate implications are case study-specific, limiting the understanding of its potential in a wider geographical scope. This thesis aims to assess the economic performance and climate impact of landfill mining in Europe towards the development of sound strategies for implementation. Different project setups are assessed in relation to varying factors at the site level such as waste composition and landfill settings, and at the system level such as policy and market conditions and background material and energy. In doing so, a factor-based method is developed and applied to generate multiple scenarios (531, 441 scenarios per project setup) and determine the underlying important factors and their interrelations that drive the results. Such understanding is used to develop and discuss strategies for improvement by addressing relevant questions for specific stakeholders, including project investors (i.e., which landfill sites to prioritize?), landfill mining practitioners (i.e., how to set up such projects?), and policymakers (i.e., which policy instruments can effectively support such projects?). Results show that landfill mining is preferable in terms of climate than economy. Possible improvements are shown by internalizing thermal treatment of combustibles and extending fines residue utilization as construction aggregates. In relation to the choice of project setups, preferable site and system-level conditions are identified in general but it is also discussed that the plausibility of finding such conditions may be difficult at present. This steers the development of more tailored strategies on what can be done now by the landfill practitioners in terms of setting up projects under current policy and market conditions in specific regions, or what can be done by the policymakers in terms of implementing various policy instruments that can drive such changes at the system level. Through this thesis, the future of landfill mining research is guided towards addressing key challenges and potential solutions for improvement. Furthermore, this thesis highlights the role of assessment as a tool for learning and guiding the development of emerging concepts such as landfill mining.

Abstract: Closing material loops and reducing resource extraction is considered to be the foundation of the circular economy that delivers environmental gains. Today, certain materials with large environmental impacts, such as plastics, are placed high on the circularity agenda. In this thesis, the market acceptance of circular plastics is analyzed. Firstly, the current – mostly linear – market for plastics in the European Union is analyzed. We find that market failure and uncertainties lead to postponed and scaled down private investments in recycling facilities for plastics. As a consequence, we conclude the failing and uncertain market needs government intervention. Secondly, potential government interventions that alleviate the market failure and reduce the present uncertainties are analyzed. Government intervention can be either incentive-based or regulatory-based. The Flemish government already acts as an incentivizer. For more than two decades already, a tax is levied on the incineration of plastic waste. We find that this tax reduces industrial plastic waste generation, but fails to elicit investments in recycling facilities. Regulatory-based policies are expected to gain in importance in the pursuit of a circular economy. Indeed, in the European Commission’s latest circularity action plan, a policy to mandate the use of recycled plastics is signaled. Mandating the use of recycled plastics can enable the circularity of plastics effectively. However, it would also generate a shock wave on the market, especially because, i.a. the implementation time of such a policy is uncertain. We investigate how firms can invest optimally in the use of recycled plastics under the presence of policy uncertainty. We conclude that the European market will be able to successfully adopt circular plastics. However, stimulating policies, both incentive-based and regulatory-based, turn out to be essential in this adoption process. Therefore, there will be a need for a combination of policies in order to prevent the incessant mass single-use consumption of plastics, which harms the environment.

Abstract: Globally, incorporation of agricultural lands into the urban boundary has been a common phenomenon. Governments use various alternatives to access the required land, including land expropriation procedures, which refers to the compulsorily taking of land from the landholders without their consent by paying compensation. In Ethiopia, the urban population is growing rapidly which resulted into an increase in the demand for urban land for housing construction, public services provision, and infrastructure developments. As the Ethiopian constitution prohibits sale of landholders, governments, at various levels, have been expropriating land from the surrounding farmers to meet the demand for urban land. The general objective of this thesis is to improve the understanding of the impacts of local land deals for urbanization on socioeconomics of farmers and the environment. The findings of this thesis revealed that there are gaps in the current practices of land expropriation for urban expansion that should be improved. The results showed that the compensation paid to the affected farmers is found to be economically inappropriate, i.e., not enough to restore the affected farmers’ livelihoods, in contrast with the land laws that allows a compensation amount that would put previous land users in a better or the same wellbeing as before the land expropriation. In addition, it is indicated that the land expropriation process does not take into account the value of ecosystem services, which are benefits obtain from the land, and important for the wellbeing of the society. We conclude that while land expropriation is an important tool to obtain land from the landholders when it is needed for public purposes, the practices in the study area show it is adversely affecting the socioeconomics of farmers and the environment.

Abstract: Novel quantum phases of matter and developing practical control over their characteristics is one of the primary aims of current condensed matter physics. It offers the potential for a new generation of energy, electronic and photonic technologies. Among all the newly found phases of matter, topological insulators are novel phases of quantum matter with fascinating bulk band topology and surface states protected by specific symmetries. For example, at the boundary of a strong topological insulator and a trivial insulator, metallic surface states appear that are protected by time-reversal symmetry. As a result, the bulk continues to be insulating, while the surface can support exotic high-mobility spin-polarized electronic states. Since there is no such thing as a clean system, impurities and other disorders are always present in materials. Even while impurities appear to be unfavorable to a system at first look, doping the host system with impurities allows us to engineer different electronic properties of systems, such as the Fermi level or electron density. Because of the symmetry protected metallic states in topological insulators, charge transport responds distinctively to magnetic and non-magnetic impurities. This doctoral dissertation explores how the longitudinal charge transport in magnetic topological thin films and the anomalous Hall effect on the surface of 3D magnetic topological insulators is influenced by point-like and randomly distributed dilute magnetic impurities. We are interested in how charge transport in these systems responds to the orientation of the magnetization orientation and how this response evolves based on the system's main characteristics, such as the magnitude of the Fermi level or gate voltage. Because topological insulators have a strong spin-orbit coupling, the interaction between conducting electrons and local magnetic impurities is very anisotropic. We will show that this anisotropy even enhances when magnetic topological thin films are exposed to a substrate or gate voltage. Therefore, to properly capture this anisotropy in charge transport calculations, we rely on a generalized Boltzmann formalism together with a modified relaxation time scheme. We show that magnetic impurities affect the charge transport in topological insulators by inducing a transition selection rule that governs scatterings of electrons between various electronic states. We see that this selection rule is highly sensitive to the spin direction of the magnetic impurities as well as the position of the Fermi level. According to this selection rule and depending on the position of the Fermi level, two different transport regimes are realized in magnetic topological thin films. In one of these regimes, our findings show that a dissipation less charge current can be generated. In other words, even if there are many magnetic impurities in the system, electrons do not notice them and, remarkably, conduct charge without dissipation. Outside this regime, the charge transport is always dissipative and its sensitivity to the spatial orientation of the magnetic impurities can be effectively modulated by a substrate or gate voltage. In this doctoral thesis, we also explore the anomalous Hall effect (AHE) on the surface of 3D magnetic topological insulators. The AHE is generated by three mechanisms: the intrinsic effect (owing to a nonzero Berry curvature), the side jump effect, and the skew scattering effect. They compete to dominate the AHE in distinct regimes. Analytically, we calculate the contributions of all three mechanisms to the scattering of massive Dirac fermions by magnetic impurities. Our results reveal three transport regimes based on the relative importance of the engaged mechanisms. The identification of these three distinctive transport regimes can assist experimentalists in achieving a regime in which each contribution is dominant over the others, allowing them to measure them separately. Typically, this is not feasible empirically since the total value of the experimentally observed AHE conceals the specific information of each of the three contributions. Based on our analytical calculations, we prove that the AHE can change sign by varying the orientation of the surface magnetization, the concentration of impurities, and the location of the Fermi level, which is consistent with previous experimental findings. In addition, we show that by suitably adjusting the given parameters, any contribution to the AHE, or even the entire AHE, can be turned off. For example, in a system with in-plane magnetization, one can turn off the AHE by pushing the system into the completely metallic regime. Furthermore, we demonstrate that any contribution to the AHE, or even the whole AHE, can be turned off by appropriately changing the provided parameters. For example, in a system with in-plane magnetization, the AHE can be turned off by pushing the system into the fully metallic regime.

Abstract: This thesis presents, in its first part, an investigation on the trembling motion of wave packets known as zitterbewegung (ZBW), in multilayer graphene, as well as in moiré excitons in twisted MoS2/WSe2 hetero-bilayers. In the last few decades, the dynamics of wave packets has been subject of many theoretical and experimental studies in various types of systems such as semiconductors, superconductors, crystalline solids and cold atoms. The discovery of graphene and moiré excitons in twisted hetero-bilayers, brought two new platforms for the investigation on time evolution of wave packets and possible observation of ZBW. This trembling motion was first theoretically predicted by Schrödinger for wave packets describing particles that obey the Dirac equation. This is exactly the case of low energy electrons in graphene, as well as of moiré exciton in twisted MoS2/WSe2 under an external applied electromagnetic field. ZBW in multilayer graphene was studied both analytically and computationally, respectively, through the Green's function and split-operator methods. In this system, it is found that ZBW depends not only on the wave packet width and initial pseudospin polarization, but also on the number of layers. Furthermore, the analytical and numerical methods proposed here allow to investigate wave packet dynamics in graphene systems with an arbitrary number of layers and arbitrary potential landscapes. For moiré excitons in twisted MoS2/WSe2 hetero-bilayers, it is shown that, analogously to other Dirac-like particles, this system also exhibits ZBW when under a perpendicular applied field. In this case, the ZBW presents long timescales that are compatible with current experimental techniques for exciton dynamics. This promotes the study of the dynamics of moiré excitons in van der Waals heterostructures as an advantageous solidstate platform to probe zitterbewegung, broadly tunable by gating and inter-layer twist angle. In the second part of this thesis, a study into graphene plasmonic in van der Waals heterostructure (vdWhs) are treated in a linear response framework within the Random Phase Approximation and with support of the quantum electrostatic heterostructure (QEH), a DFT-based method. Since Dirac plasmons in graphene are very sensitive to the dielectric properties of the environment, it is possible to explore this property to probe the structure and composition of van der Waals heterostructures (vdWh) placed underneath a single graphene layer. In this way, one can achieve a layer sensitivity of a single layer and differentiate between different TMDs for heterostructures thicker than 2 layers. As a consequence of this, study, the hybridization of Dirac plasmons in graphene with phonons of transition metal dichalcogenides (TMDs), when the materials are combined in so-called van der Waals heterostructures (vdWh) forming surface plasmon-phonon polaritons (SPPPs) are also investigated. It was found that it is possible to realize both strong and ultrastrong coupling regimes by tuning graphene’s Fermi energy and changing TMD layer number.

Abstract: Over the decades, Bayesian statistical inference has become a staple technique for modelling human multisensory perception. Many studies have successfully shown how sensory and prior information can be combined to optimally interpret our environment. Because of the multiple sound localisation cues available in the binaural signal, sound localisation models based on Bayesian inference are a promising way of explaining behavioural human data. An interesting aspect is the consideration of dynamic localisation cues obtained through self-motion. Here we provide a review of the recent developments in modelling dynamic sound localisation with a particular focus on Bayesian inference. Further, we describe a theoretical Bayesian framework capable to model dynamic and active listening situations in humans in a static auditory environment. In order to demonstrate its potential in future implementations, we provide results from two examples of simplified versions of that framework.

Abstract: The first covalently linked conjugate of metal phthalocyaninate and chlorin e(6) derivative has been obtained by transesterification of alpha-ketomethyl ester in methylpheophorbide a with zinc(II) 2-(2-hydroxymethylbenzyloxy)-9(10),16(17),23(24)-tri-tert-butylphthalocyaninate under mild conditions. The dyad exhibits a panchromatic nature revealing both the phthalocyanine and pheophorbide derived bands in the UV-Vis absorption spectrum. The H-1 NMR spectroscopy data combined with theoretical calculations indicate the presence of spatial intramolecular interactions between the phthalocyanine, pheophorbide and spacer fragments of the dyad allowing to forecast its enhanced nonlinear optical properties, as well as the characteristic energy transfer from the excited pheophorbide subunit to the phthalocyanine core. Indeed, when excited in the UV-Vis range, the conjugate shows red fluorescence with the spectral maximum at 686 nm, which is close to the one of the initial zinc phthalocyaninate. Furthermore, the dyad effectively generates singlet oxygen and, in the presence of polyvinylpyrrolidone (PVP) as biocompatible solubilizer, forms stable micellar saline solutions with the particles ranged in size between 40 and 100 nm. These nanoparticles represent promising third-generation photosensitizing systems for application in theranostics.

Abstract: In the biogeochemical flows on Earth, the reactive nitrogen (Nr) level has three times surpassed the safe boundary. The severe transgression of this boundary goes against sustainable planetary development. The modern food production process excessively relies on synthetic Nr fertilizers from the Haber– Bosch process. However, the massive loss of valuable nitrogen resources (i.e., 78-89%) from agriculture has been causing severe nitrogen cascade. Besides, the domestic wastewater in some local areas is discharged without proper treatment, making it a nonnegligible source of Nr pollution for local water bodies. Anthropogenic activities keep pumping out Nr pollution via point-source and non-point-source (NPS) emissions. Compared to the NPS emissions, point sources give visible and identified waste streams. It is vital to intervene the nitrogen cascade from point sources and facilitate humanity back to the safe Nr boundary. The collected and collectible Nr streams from food production, waste management, and recycling secondary raw materials can be used as waste-based fertilizers for agricultural cultivation. Besides the well-investigated recovery of inorganic Nr, organic Nr accounts for a massive Nr proportion on the Earth. Proper handling and treatment make these useful organic fertilizers for soil-based cultivation. However, these organic Nr fertilizers cannot directly apply to fertigation or hydroponic cultivation systems, and further biological conversion via nitrogen mineralization and nitrification to nitrate is essential. Besides the direct Nr cycling, the indirect Nr cycling ‘over the atmosphere’ should also be considered. In this way, the nitrogen cycle can be completed via converting the waste Nr back to nitrogen gas (i.e., Nr removal) and then synthesizing into Nr again. The municipal wastewater treatment plants receive a vast amount of low-strength Nr wastewater (mainly as ammonium) daily. Compared to the conventional nitrification/denitrification process, partial nitritation/anammox (PN/A) is considered a resource- and cost-effective technology for wastewater with a low COD/N ratio. Moreover, the novel autotrophic denitratation/anammox process could be a good Nr removal process for wastewater containing both ammonium and nitrate. This Ph.D. thesis aimed to develop Nr recovery, conversion, and removal bioreactor strategies for different types of waste streams and biomass. Nr recovery was investigated on high-strength Nr waste streams for fertigation or hydroponic applications in Chapters 2 and 3. On the other hand, Nr removal was studied on the medium- to low-strength Nr waste streams in Chapters 4 and 5. In Chapter 2, a novel mineralization and nitrification system was proposed, producing nutrient solutions from solid organic fertilizers for hydroponic systems. Batch tests showed that aerobic incubation at 35°C could realize the NO₃⁻-N production efficiency above 90% from a novel microbial fertilizer. Subsequently, in the stirred tank bioreactor test, NO₃⁻-N production efficiency stabilized in a range of 44-51% under the influent loading rate of 400 mg TN L⁻¹ d⁻¹ at a 5-day HRT. Using Ca(OH)₂ and Mg(OH)₂ as pH control reagents generated the nutrient solutions with different P, Ca, and Mg nutrient levels. After modeling the nutrient balancing process, the proportion of organic-sourced NO₃⁻-N in the Hoagland nutrient solution (HNS) of Ca(OH)₂ scenario was 92.7%, while only 37.4% in the Mg(OH)₂ scenario. Compared to commercial scenarios, the total costs of the organic-sourced HNS can be cost-competitive for hydroponic cultivation. In Chapter 3, the Nr recovery as nitrate (NO₃⁻-N) from diluted human urine (around 670 mg N L⁻¹) was explored in a trickling filter (TF) for the first time. A novel concept of in-situ integrating the TF system into hydroponic systems was proposed as meaningful progress towards sustainable agriculture. The difference between synthetic and real urine in nitrification efficiency was found to be negligible. The full nitrification of alkalinized real urine was realized in the pH-controlled TF by calcium hydroxide (Ca(OH)₂) at around pH 6. The TF could handle different urine collection batches and maintain relatively stable nitrification performance, with NO₃⁻-N production efficiency and rate of 88±3% and 136±4 mg N L⁻¹ d⁻¹, respectively. The optimal HLR to realize this nitrification performance was 2 m³ m⁻² h⁻¹, with energy consumption of 1.8 kWh electricity kg⁻¹ NO₃⁻-N production. Ca(OH)₂, as a cheap base, its triple advantages on urine alkalinization, full nitrification, and macronutrient supplementation were successfully demonstrated in our proposed concept. In Chapter 4, towards more sustainable wastewater treatment, the feasibility of one-stage partial nitritation/anammox (PN/A) was investigated in three parallel packed-bed trickling filters (TFs), with three types of carrier materials of different specific surface areas. Synthetic wastewater containing 100-250 mg NH₄⁺-N L⁻¹ was tested to mimic medium-strength household waste streams after carbon removal. Interestingly, the cheap carrier based on expanded clay achieved similar rates as commercially used plastic carrier materials. The top passive ventilation combined with an optimum hydraulic loading rate of 1.8 m³ m⁻² h⁻¹ could reach approximately 60% total nitrogen (TN) removal at a rate of 300 mg N L⁻¹ d⁻¹. A relatively low NO₃⁻-N production (13%) via PN/A was achieved in TFs. Most of the TN removal took place in the top compartment, where anammox activity was the highest. Energy consumption estimation (0.78 kWh electricity g⁻¹ N removed) suggested that the proposed process could be a suitable low-cost alternative for nitrogen removal. In Chapter 5, coupling sulfur-driven denitratation (SDN) with anammox was proposed to treat the wastewater containing both NO₃⁻-N and NH₄⁺-N, like the secondary effluents of mainstream PN/A processes. To explore the feasibility of sufficient and stable NO₂⁻-N accumulation via SDN in the long term, the effects of pH setpoints, residual NO₃⁻-N level, and biomass-specific NO₃⁻-N loading rate (BSNLR) were investigated. Alternating the pH setpoints between 7.0 and 8.5 could temporarily stimulate the NO₂⁻-N accumulation. Both the residual NO₃⁻-N and BSNLR showed highly positive correlations with the NO₂⁻-N accumulation efficiency. Under the control of pH 8.5, 1.0±0.8 mg NO₃⁻-N L⁻¹ and 150±42 mg NO₃⁻-N g⁻¹ VSS d⁻¹, SDN could produce 6.4±1.0 mg NO₂⁻-N L⁻¹ in the short term. Thiobacillus members may play a crucial role in managing the NO₂⁻-N accumulation, but the reduction of abundance and possible adaptation significantly impaired the efficacy of control strategies in the long run. Overall, novel technologies have been proposed to sustainably convert Nr in waste streams and biomass. The decision for Nr recovery versus removal and synthesis should be based on specific cases with the best environmental, economic, and human-health sustainability. In the future, the Nr management concepts should be further improved to make the nitrogen cycle more sustainable with higher resource use efficiency and less Nr emissions to the environment. Although the thesis is mainly focused on limited types of Nr waste streams, it pointed out the direction of sustainable Nr management and could facilitate the Nr back to the safe boundary in the long run.

Abstract: Low-temperature plasma has received extensive attention due to its promising application prospects in the field of air pollutants degradation and energy conversion. To fulfill the need for particular applications, constructing stable plasma sources and investigating the interaction mechanisms between plasma and substances have been hot research topics. This thesis reports the diagnosis and improvement of plasma sources, diagnosis of the active species in plasma and a modeling study of chemical kinetics processes. The main research contents are as follows: In Chapter 3, a diffuse sine AC dielectric barrier discharge (DBD) is successfully obtained by optimizing the electrode structure. It is found that using double-layer dielectric plates can limit the discharge current intensity and significantly improve the discharge uniformity. The electrical characteristics and gas temperature with different operating time show that the discharge stability is also improved by using double-layer dielectric plates. In Chapter 4, nanosecond pulses are employed to generate diffuse DBD plasmas. Three main discharge stages are distinguished by ICCD images, i.e., the streamer breakdown from the needle tip to the plate electrode, the regime transition from streamer to diffuse plasma, and the propagation of surface discharge on the plate electrode surface. The chapter reveales that in nanosecond pulsed discharges the vibrational temperature of N2 increases with the discharge duration, while the rotational temperature mainly stays constant, which means electron energy is transferred into the vibrational levels, but gas heating is not obvious during the discharge pulse. In Chapter 5, both sine AC DBD and nanosecond pulsed DBD, studied in Chapter 2 and 3, are used for formaldehyde degradation. It is found that nanosecond pulsed DBD has more homogenous characteristics, better stability, and lower plasma gas temperature. Moreover, the energy consumption of nanosecond pulsed DBD is much lower than that of AC DBD. In Chapter 6, a 0D chemical kinetics model is developed to investigate the underlying plasma chemistry of methane dry reforming in a nanosecond pulsed discharge. An overview of the dominant reaction pathways of CO2 and CH4 conversion into the major products is given. Furthermore, most of the CO2 molecules are populated into vibrational states during the pulse. Hence, the vibrational states of CO2 play an important role in its dissociation process. In general, this PhD thesis contributes to a better insight in the mechanisms of sinusoidal AC DBD and nanosecond pulsed DBD plasmas and their applications, i.e., decomposition of formaldehyde and dry reforming of methane.