|
Records |
Links |
|
Author |
Thomassen, G.; Van Dael, M.; Lemmens, B.; Van Passel, S. |
|
|
Title |
A review of the sustainability of algal-based biorefineries : towards an integrated assessment framework |
Type |
A1 Journal article |
|
Year |
2017 |
Publication |
Renewable & Sustainable Energy Reviews |
Abbreviated Journal |
Renew Sust Energ Rev |
|
|
Volume |
68 |
Issue |
2 |
Pages |
876-887 |
|
|
Keywords |
A1 Journal article; Economics; Engineering sciences. Technology; Engineering Management (ENM) |
|
|
Abstract |
Algal-based bioenergy products have faced multiple economic and environmental problems. To counter these problems, algal-based biorefineries have been proposed as a promising solution. Multiple environmental and economic assessments have analyzed this concept. However, a wide variation in results was reported. This study performs a review to evaluate the methodological reasons behind this variation. Based on this review, four main challenges for a sustainability assessment were identified: 1) the use of a clear framework; 2) the adaptation of the methodology to all stages of technological maturity; 3) the use of harmonized assumptions; 4) the integration of the technological process. A generic methodology, based on the integration of a techno-economic assessment methodology and a streamlined life cycle assessment was proposed. This environmental techno-economic assessment can be performed following an iterative approach during each stage of technology development. In this way, crucial technological parameters can be directly identified and evaluated during the maturation of the technology. The use of this assessment methodology can therefore act as guidance to decrease the time-to-market for innovative and sustainable technologies. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000391899400005 |
Publication Date |
2016-03-16 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1364-0321; 1879-0690 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
8.05 |
Times cited |
23 |
Open Access |
|
|
|
Notes |
; ; |
Approved |
Most recent IF: 8.05 |
|
|
Call Number |
UA @ admin @ c:irua:139038 |
Serial |
6245 |
|
Permanent link to this record |
|
|
|
|
Author |
Snoeckx, R.; Heijkers, S.; Van Wesenbeeck, K.; Lenaerts, S.; Bogaerts, A. |
|
|
Title |
CO2conversion in a dielectric barrier discharge plasma: N2in the mix as a helping hand or problematic impurity? |
Type |
A1 Journal article |
|
Year |
2016 |
Publication |
Energy & environmental science |
Abbreviated Journal |
Energ Environ Sci |
|
|
Volume |
9 |
Issue |
9 |
Pages |
999-1011 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT); Sustainable Energy, Air and Water Technology (DuEL) |
|
|
Abstract |
Carbon dioxide conversion and utilization has gained significant interest over the years. A novel gas conversion technique with great potential in this area is plasma technology. A lot of research has already been performed, but mostly on pure gases. In reality, N2 will always be an important impurity in effluent
gases. Therefore, we performed an extensive combined experimental and computational study on the effect of N2 in the range of 1–98% on CO2 splitting in dielectric barrier discharge (DBD) plasma. The presence of up to 50% N2 in the mixture barely influences the effective (or overall) CO2 conversion and energy efficiency, because the N2 metastable molecules enhance the absolute CO2 conversion, and this compensates for the lower CO2 fraction in the mixture. Higher N2 fractions, however, cause a drop in the CO2 conversion and energy efficiency. Moreover, in the entire CO2/N2 mixing ratio, several harmful compounds, i.e., N2O and NOx compounds, are produced in the range of several 100 ppm. The reaction pathways for the formation of these compounds are explained based on a kinetic analysis, which allows proposing solutions on how to prevent the formation of these harmful compounds. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000372243600030 |
Publication Date |
2015-12-15 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1754-5692 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
29.518 |
Times cited |
68 |
Open Access |
|
|
|
Notes |
The authors acknowledge financial support from the IAP/7 (Inter-university Attraction Pole) program ‘PSI-Physical Chemistry of Plasma-Surface Interactions’, financially supported by the Belgian Federal Office for Science Policy (BELSPO), as well as the Fund for Scientific Research Flanders (FWO). This work was carried out in part using the Turing HPC infrastructure at the CalcUA core facility of the Universiteit Antwerpen, a division of the Flemish Supercomputer Center VSC, funded by the Hercules Foundation, the Flemish Government (department EWI) and the University of Antwerp. |
Approved |
Most recent IF: 29.518 |
|
|
Call Number |
c:irua:133169 |
Serial |
4020 |
|
Permanent link to this record |
|
|
|
|
Author |
Berdiyorov, G.R.; Madjet, M.E.; El-Mellouhi, F.; Peeters, F.M. |
|
|
Title |
Effect of crystal structure on the electronic transport properties of the organometallic perovskite CH3NH3PbI3 |
Type |
A1 Journal article |
|
Year |
2016 |
Publication |
Solar energy materials and solar cells
T2 – 2nd International Renewable and Sustainable Energy Conference (IRSEC), OCT 17-19, 2014, Ouarzazate, MOROCCO |
Abbreviated Journal |
Sol Energ Mat Sol C |
|
|
Volume |
148 |
Issue |
148 |
Pages |
60-66 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT) |
|
|
Abstract |
Using density-functional theory in combination with the nonequilibrium Green's function formalism, we study the effect of the crystal lattice structure of organometallic perovskite CH3NH3PbI3 on its electronic transport properties. Both dispersive interactions and spin-orbit coupling are taken into account in describing structural and electronic properties of the system. We consider two different phases of the material, namely the orthorhombic and cubic lattice structures, which are energetically stable at low (< 160 K) and high (> 330 K) temperatures, respectively. The sizable geometrical differences between the two structures in term of lattice parameters, PbI6 octahedral tilts, rotation and deformations, have considerable impact on the transport properties of the material. For example, at zero bias and for all considered electron energies, the cubic phase has a larger transmission than the orthorhombic one, although both show similar electronic densities of states. Depending on the applied voltage, the current in the cubic system can be several orders of magnitude larger as compared to the one obtained for the orthorhombic sample. We attribute this enhancement in the transmission to the presence of extended states in the cubic phase due to the symmetrically shaped and ordered PbI6 octaherdra. (C) 2015 Elsevier B.V. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
Elsevier science bv |
Place of Publication |
Amsterdam |
Editor |
|
|
|
Language |
|
Wos |
000371944500011 |
Publication Date |
2015-11-06 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0927-0248 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
4.784 |
Times cited |
16 |
Open Access |
|
|
|
Notes |
; ; |
Approved |
Most recent IF: 4.784 |
|
|
Call Number |
UA @ lucian @ c:irua:133151 |
Serial |
4163 |
|
Permanent link to this record |
|
|
|
|
Author |
Berdiyorov, G.R.; El-Mellouhi, F.; Madjet, M.E.; Alharbi, F.H.; Peeters, F.M.; Kais, S. |
|
|
Title |
Effect of halide-mixing on the electronic transport properties of organometallic perovskites |
Type |
A1 Journal article |
|
Year |
2016 |
Publication |
Solar energy materials and solar cells
T2 – 2nd International Renewable and Sustainable Energy Conference (IRSEC), OCT 17-19, 2014, Ouarzazate, MOROCCO |
Abbreviated Journal |
Sol Energ Mat Sol C |
|
|
Volume |
148 |
Issue |
148 |
Pages |
2-10 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT) |
|
|
Abstract |
Using density-functional theory in combination with the nonequilibrium Green's function formalism, we study the effect of iodide/chloride and iodide/bromide mixing on the electronic transport in lead based organometallic perovskite CH3NH3PbI3, which is known to be an effective tool to tune the electronic and optical properties of such materials. We found that depending on the level and position of the halide mixing, the electronic transport can be increased by more than a factor of 4 for a given voltage biasing. The largest current is observed for small concentration of bromide substitutions located at the equatorial sites. However, full halide substitution has a negative effect on the transport properties of this material: the current drops by an order of magnitude for both CH3NH3PbCl3 and CH3NH3PbBr3 samples. (C) 2015 Elsevier B.V. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
Elsevier science bv |
Place of Publication |
Amsterdam |
Editor |
|
|
|
Language |
|
Wos |
000371944500002 |
Publication Date |
2015-12-18 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0927-0248 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
4.784 |
Times cited |
23 |
Open Access |
|
|
|
Notes |
; ; |
Approved |
Most recent IF: 4.784 |
|
|
Call Number |
UA @ lucian @ c:irua:133150 |
Serial |
4165 |
|
Permanent link to this record |
|
|
|
|
Author |
Neubert, S.; Mitoraj, D.; Shevlin, S.A.; Pulisova, P.; Heimann, M.; Du, Y.; Goh, G.K.L.; Pacia, M.; Kruczała, K.; Turner, S.; Macyk, W.; Guo, Z.X.; Hocking, R.K.; Beranek, R.; |
|
|
Title |
Highly efficient rutile TiO2 photocatalysts with single Cu(II) and Fe(III) surface catalytic sites |
Type |
A1 Journal article |
|
Year |
2016 |
Publication |
Journal of materials chemistry A : materials for energy and sustainability |
Abbreviated Journal |
J Mater Chem A |
|
|
Volume |
4 |
Issue |
4 |
Pages |
3127-3138 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
|
Abstract |
Highly active photocatalysts were obtained by impregnation of nanocrystalline rutile TiO2 powders with small amounts of Cu(II) and Fe(III) ions, resulting in the enhancement of initial rates of photocatalytic degradation of 4-chlorophenol in water by factors of 7 and 4, compared to pristine rutile, respectively. Detailed structural analysis by EPR and X-ray absorption spectroscopy (EXAFS) revealed that Cu(II) and Fe(III) are present as single species on the rutile surface. The mechanism of the photoactivity enhancement was elucidated by a combination of DFT calculations and detailed experimental mechanistic studies including photoluminescence measurements, photocatalytic experiments using scavengers, OH radical detection, and photopotential transient measurements. The results demonstrate that the single Cu(II) and Fe(III) ions act as effective cocatalytic sites, enhancing the charge separation, catalyzing “dark” redox reactions at the interface, thus improving the normally very low quantum yields of UV light-activated TiO2 photocatalysts. The exact mechanism of the photoactivity enhancement differs depending on the nature of the cocatalyst. Cu(II)-decorated samples exhibit fast transfer of photogenerated electrons to Cu(II/I) sites, followed by enhanced catalysis of dioxygen reduction, resulting in improved charge separation and higher photocatalytic degradation rates. At Fe(III)-modified rutile the rate of dioxygen reduction is not improved and the photocatalytic enhancement is attributed to higher production of highly oxidizing hydroxyl radicals produced by alternative oxygen reduction pathways opened by the presence of catalytic Fe(III/II) sites. Importantly, it was demonstrated that excessive heat treatment (at 450 degrees C) of photocatalysts leads to loss of activity due to migration of Cu(II) and Fe(III) ions from TiO2 surface to the bulk, accompanied by formation of oxygen vacancies. The demonstrated variety of mechanisms of photoactivity enhancement at single site catalyst-modified photocatalysts holds promise for developing further tailored photocatalysts for various applications. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
Cambridge |
Editor |
|
|
|
Language |
|
Wos |
000371077300040 |
Publication Date |
2015-12-30 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2050-7488; 2050-7496 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
8.867 |
Times cited |
44 |
Open Access |
|
|
|
Notes |
|
Approved |
Most recent IF: 8.867 |
|
|
Call Number |
UA @ lucian @ c:irua:132322 |
Serial |
4191 |
|
Permanent link to this record |
|
|
|
|
Author |
Callini, E.; Aguey-Zinsou, K.F.; Ahuja, R.; Ares, J.R.; Bals, S.; Biliškov, N.; Chakraborty, S.; Charalambopoulou, G.; Chaudhary, A.L.; Cuevas, F.; Dam, B.; de Jongh, P.; Dornheim, M.; Filinchuk, Y.; Grbović Novaković, J.; Hirscher, M.; Jensen, T.R.; Jensen, P.B.; Novaković, N.; Lai, Q.; Leardini, F.; Gattia, D.M.; Pasquini, L.; Steriotis, T.; Turner, S.; Vegge, T.; Züttel, A.; Montone, A. |
|
|
Title |
Nanostructured materials for solid-state hydrogen storage : a review of the achievement of COST Action MP1103 |
Type |
A1 Journal article |
|
Year |
2016 |
Publication |
International journal of hydrogen energy
T2 – E-MRS Fall Meeting / Symposium C on Hydrogen Storage in Solids -, Materials, Systems and Aplication Trends, SEP 15-18, 2015, Warsaw, POLAND |
Abbreviated Journal |
Int J Hydrogen Energ |
|
|
Volume |
41 |
Issue |
41 |
Pages |
14404-14428 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
|
Abstract |
In the framework of the European Cooperation in Science and Technology (COST) Action MP1103 Nanostructured Materials for Solid-State Hydrogen Storage were synthesized, characterized and modeled. This Action dealt with the state of the art of energy storage and set up a competitive and coordinated network capable to define new and unexplored ways for Solid State Hydrogen Storage by innovative and interdisciplinary research within the European Research Area. An important number of new compounds have been synthesized: metal hydrides, complex hydrides, metal halide ammines and amidoboranes. Tuning the structure from bulk to thin film, nanoparticles and nanoconfined composites improved the hydrogen sorption properties and opened the perspective to new technological applications. Direct imaging of the hydrogenation reactions and in situ measurements under operando conditions have been carried out in these studies. Computational screening methods allowed the prediction of suitable compounds for hydrogen storage and the modeling of the hydrogen sorption reactions on mono-, bi-, and three-dimensional systems. This manuscript presents a review of the main achievements of this Action. (C) 2016 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
Pergamon-elsevier science ltd |
Place of Publication |
Oxford |
Editor |
|
|
|
Language |
|
Wos |
000381950800051 |
Publication Date |
2016-05-08 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0360-3199 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
3.582 |
Times cited |
89 |
Open Access |
Not_Open_Access |
|
|
Notes |
All the authors greatly thank the COST Action MP1103 for financial support. |
Approved |
Most recent IF: 3.582 |
|
|
Call Number |
UA @ lucian @ c:irua:135723 |
Serial |
4307 |
|
Permanent link to this record |
|
|
|
|
Author |
Naik, P.V.; Wee, L.H.; Meledina, M.; Turner, S.; Li, Y.; Van Tendeloo, G.; Martens, J.A.; Vankelecom, I.F.J. |
|
|
Title |
PDMS membranes containing ZIF-coated mesoporous silica spheres for efficient ethanol recovery via pervaporation |
Type |
A1 Journal article |
|
Year |
2016 |
Publication |
Journal of materials chemistry A : materials for energy and sustainability |
Abbreviated Journal |
J Mater Chem A |
|
|
Volume |
4 |
Issue |
4 |
Pages |
12790-12798 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
|
Abstract |
The design of functional micro- and mesostructured composite materials is significantly important for separation processes. Mesoporous silica is an attractive material for fast diffusion, while microporous zeolitic imidazolate frameworks (ZIFs) are beneficial for selective adsorption and diffusion. In this work, ZIF-71 and ZIF-8 nanocrystals were grown on the surface of mesoporous silica spheres (MSS) via the seeding and regrowth approach in order to obtain monodispersed MSS-ZIF-71 and MSS-ZIF-8 spheres with a particle size of 2-3 mm. These MSS-ZIF spheres were uniformly dispersed into a polydimethylsiloxane (PDMS) matrix to prepare mixed matrix membranes (MMMs). These MMMs were evaluated for the separation of ethanol from water via pervaporation. The pervaporation results reveal that the MSS-ZIF filled MMMs substantially improve the ethanol recovery in both aspects viz. flux and separation factor. These MMMs outperforms the unfilled PDMS membranes and the conventional carbon and zeolite filled MMMs. As expected, the mesoporous silica core allows very fast flow of the permeating compound, while the hydrophobic ZIF coating enhances the ethanol selectivity through its specific pore structure, hydrophobicity and surface chemistry. It can be seen that ZIF-8 mainly has a positive impact on the selectivity, while ZIF-71 enhances fluxes more significantly. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
Cambridge |
Editor |
|
|
|
Language |
|
Wos |
000382015100012 |
Publication Date |
2016-07-12 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2050-7488; 2050-7496 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
8.867 |
Times cited |
26 |
Open Access |
|
|
|
Notes |
|
Approved |
Most recent IF: 8.867 |
|
|
Call Number |
UA @ lucian @ c:irua:137188 |
Serial |
4395 |
|
Permanent link to this record |
|
|
|
|
Author |
Van Havenbergh, K.; Turner, S.; Marx, N.; Van Tendeloo, G. |
|
|
Title |
The mechanical behavior during (de)lithiation of coated silicon nanoparticles as anode material for lithium-ion batteries studied by InSitu transmission electron microscopy |
Type |
A1 Journal article |
|
Year |
2016 |
Publication |
Energy technology |
Abbreviated Journal |
Energy Technol-Ger |
|
|
Volume |
4 |
Issue |
4 |
Pages |
1005-1012 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
|
Abstract |
One approach to cope with the continuous irreversible capacity loss in Si-based electrodes, attributed to lithiation-induced volume changes and the formation of a solid-electrolyte interface (SEI), is by coating silicon nanoparticles. A coating can improve the conductivity of the electrode, form a chemical shield against the electrolyte, or provide mechanical confinement to reduce the volume increase. The influence of such a coating on the mechanical behavior of silicon nanoparticles during Li insertion and Li extraction was investigated by insitu transmission electron microscopy. The type of coating was shown to influence the size of the unreacted core that remains after reaction of silicon with lithium. Furthermore, two mechanisms to relieve the stress generated during volume expansion are reported: the initiation of cracks and the formation of nanovoids. Both result in a full reaction of the silicon nanoparticles, whereas with the formation of cracks, additional surface area is created, on which an SEI can be formed. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000382549500012 |
Publication Date |
2016-06-29 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2194-4296; 2194-4288 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.789 |
Times cited |
6 |
Open Access |
|
|
|
Notes |
|
Approved |
Most recent IF: NA |
|
|
Call Number |
UA @ lucian @ c:irua:137167 |
Serial |
4406 |
|
Permanent link to this record |
|
|
|
|
Author |
Çakir, D.; Sevik, C.; Gulseren, O.; Peeters, F.M. |
|
|
Title |
Mo2C as a high capacity anode material: a first-principles study |
Type |
A1 Journal article |
|
Year |
2016 |
Publication |
Journal of materials chemistry A : materials for energy and sustainability |
Abbreviated Journal |
J Mater Chem A |
|
|
Volume |
4 |
Issue |
16 |
Pages |
6029-6035 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Condensed Matter Theory (CMT) |
|
|
Abstract |
The adsorption and diffusion of Li, Na, K and Ca atoms on a Mo2C monolayer are systematically investigated by using first principles methods. We found that the considered metal atoms are strongly bound to the Mo2C monolayer. However, the adsorption energies of these alkali and earth alkali elements decrease as the coverage increases due to the enhanced repulsion between the metal ions. We predict a significant charge transfer from the ad-atoms to the Mo2C monolayer, which indicates clearly the cationic state of the metal atoms. The metallic character of both pristine and doped Mo2C ensures a good electronic conduction that is essential for an optimal anode material. Low migration energy barriers are predicted as small as 43 meV for Li, 19 meV for Na and 15 meV for K, which result in the very fast diffusion of these atoms on Mo2C. For Mo2C, we found a storage capacity larger than 400 mA h g(-1) by the inclusion of multilayer adsorption. Mo2C expands slightly upon deposition of Li and Na even at high concentrations, which ensures the good cyclic stability of the atomic layer. The calculated average voltage of 0.68 V for Li and 0.30 V for Na ions makes Mo2C attractive for low charging voltage applications. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
Cambridge |
Editor |
|
|
|
Language |
|
Wos |
000374790700033 |
Publication Date |
2016-03-18 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2050-7488; 2050-7496 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
8.867 |
Times cited |
202 |
Open Access |
|
|
|
Notes |
; This work was supported by the Flemish Science Foundation (FWO-Vl) and the Methusalem foundation of the Flemish government. Computational resources were provided by TUBITAK ULAKBIM, High Performance and Grid Computing Center (TR-Grid e-Infrastructure), and HPC infrastructure of the University of Antwerp (CalcUA) a division of the Flemish Supercomputer Center (VSC), which is funded by the Hercules foundation. C. S. acknowledges the support from Turkish Academy of Sciences (TUBA-GEBIP). C. S acknowledges the support from Anadolu University (Grant No. 1407F335). We acknowledge the support from TUBITAK, The Scientific and Technological Research Council of Turkey (Grant No. 115F024). ; |
Approved |
Most recent IF: 8.867 |
|
|
Call Number |
UA @ lucian @ c:irua:144763 |
Serial |
4669 |
|
Permanent link to this record |
|
|
|
|
Author |
Afsharzade, N.; Papzan, A.; Ashjaee, M.; Delangizan, S.; Van Passel, S.; Azadi, H. |
|
|
Title |
Renewable energy development in rural areas of Iran |
Type |
A1 Journal article |
|
Year |
2016 |
Publication |
Renewable & Sustainable Energy Reviews |
Abbreviated Journal |
Renew Sust Energ Rev |
|
|
Volume |
65 |
Issue |
|
Pages |
743-755 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM) |
|
|
Abstract |
Iran's energy system is extremely dependent on fossil fuels which, in turn, have led to problems such as fossil fuels depletion, social, economic and environmental damage and territorial imbalance. The country should therefore design a sustainable energy system based on clean energy as well as renewable energy. Accordingly, and given that Iran's rural areas suffer from the unsustainable energy system, it is necessary to integrate renewable energy into comprehensive development programs in general, and into rural development programs, specifically. This review paper answers the following questions: Why is renewable energy important for Iran at national and rural levels? How is renewable energy related to sustainable rural development? and What are the challenges in the promotion of renewable energy technologies in Iran? The paper concludes that although renewable energy has potential for development in Iran's rural areas due to environmental, social and economic advantages, it could face some infrastructural, managerial, socio-cultural and economic challenges. Accordingly, aggressive and innovative policy making is required to meet these challenges. (C) 2016 Elsevier Ltd. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000383293800053 |
Publication Date |
2016-07-23 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1364-0321; 1879-0690 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
8.05 |
Times cited |
41 |
Open Access |
|
|
|
Notes |
; ; |
Approved |
Most recent IF: 8.05 |
|
|
Call Number |
UA @ admin @ c:irua:137105 |
Serial |
6243 |
|
Permanent link to this record |
|
|
|
|
Author |
Lizin, S.; Van Passel, S.; Vranken, L. |
|
|
Title |
Heterogeneity in the solar-powered consumer electronics market : a discrete choice experiments study |
Type |
A1 Journal article |
|
Year |
2016 |
Publication |
Solar Energy Materials And Solar Cells |
Abbreviated Journal |
Sol Energ Mat Sol C |
|
|
Volume |
156 |
Issue |
|
Pages |
140-146 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM) |
|
|
Abstract |
Solar-powered consumer electronics are a likely starting point for organic photovoltaic (OPV) market development. Therefore, a generic discrete choice experiments study can determine how Flemish consumers value solar-cell characteristics for solar-poweied consumer electronics. Such characteristics include efficiency, lifetime, aesthetics, integratability, and price. We contribute to the literature by investigating preference heterogeneity in a solar-power niche market with an experimental design with a fixed reference alternative. The error components random parameter logit (ECRPL) with interactions provides a better fit than the latent class (LC) model for our choice data. The main effects had the expected signs. Consequently, aesthetics and integratability are OPV's assets. Nevertheless, heterogeneity puts the results that are valid for the average consumer into perspective. Based on our findings, OPV commercialization efforts should target the experienced, impatient user who highly values design and functionality. (C) 2016 Elsevier B.V. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000383304100015 |
Publication Date |
2016-06-27 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0927-0248 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
4.784 |
Times cited |
2 |
Open Access |
|
|
|
Notes |
; Sebastien Lizin thanks the Research Foundation Flanders (FWO) for funding his postdoctoral mandate with Grant number 12G5415N, without which it would have been impossible to revise this work. ; |
Approved |
Most recent IF: 4.784 |
|
|
Call Number |
UA @ admin @ c:irua:137107 |
Serial |
6207 |
|
Permanent link to this record |
|
|
|
|
Author |
Paolella, A.; Bertoni, G.; Hovington, P.; Feng, Z.; Flacau, R.; Prato, M.; Colombo, M.; Marras, S.; Manna, L.; Turner, S.; Van Tendeloo, G.; Guerfi, A.; Demopoulos, G.P.; Zaghib, K.; |
|
|
Title |
Cation exchange mediated elimination of the Fe-antisites in the hydrothermal synthesis of LiFePO4 |
Type |
A1 Journal article |
|
Year |
2015 |
Publication |
Nano energy |
Abbreviated Journal |
Nano Energy |
|
|
Volume |
16 |
Issue |
16 |
Pages |
256-267 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
|
Abstract |
In this work we elucidate the elimination of mechanism Fe-antisite defects in lithium iron phosphate (LiFePO4) during the hydrothermal synthesis. Compelling evidence of this effect is provided by combining Neutron Powder Diffraction (NPD), High Resolution (Scanning) Transmission Electron Microscopy (HR-(S)TEM), Electron Energy Loss Spectroscopy (EELS), X-Ray Photoelectron Spectroscopy (XPS) and calculations. We found: i) the first intermediate vivianite inevitably creates Fe-antisite defects in LiFePO4; ii) the removal of these antisite defects by cation exchange is assisted by a nanometer-thick amorphous layer, rich in Li, that enwraps the LiFePO4 crystals. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000364579300027 |
Publication Date |
2015-06-19 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2211-2855; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
12.343 |
Times cited |
27 |
Open Access |
|
|
|
Notes |
The authorswanttoacknowledgeVincentGariepy,Cathe- rine Gagnon,JulieTrottier,DanielClement,Dr.CyrilFaure of IREQ,Dr.GaiaTomaselloofInstitutfürTheoretische PhysikFreieUniversitätBerlinandProf.MichelArmandof CICenergigune forhelpfuldiscussionsandtechnical supports. |
Approved |
Most recent IF: 12.343; 2015 IF: 10.325 |
|
|
Call Number |
c:irua:127688 |
Serial |
296 |
|
Permanent link to this record |
|
|
|
|
Author |
Delmelle, R.; Amin-Ahmadi, B.; Sinnaeve, M.; Idrissi, H.; Pardoen, T.; Schryvers, D.; Proost, J. |
|
|
Title |
Effect of structural defects on the hydriding kinetics of nanocrystalline Pd thin films |
Type |
A1 Journal article |
|
Year |
2015 |
Publication |
International journal of hydrogen energy |
Abbreviated Journal |
Int J Hydrogen Energ |
|
|
Volume |
40 |
Issue |
40 |
Pages |
7335-7347 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
|
Abstract |
While the microstructure of a metal is well-known to affect its equilibrium hydrogen uptake and therefore the hydriding thermodynamics, microstructural effects on the hydriding kinetics are much less documented. Moreover, for thin film systems, such microstructural effects are difficult to separate from the internal stress effect, since most defects generate internal stresses. Such a decoupling has been achieved in this paper for nanocrystalline Pd thin film model systems through the use of a high-resolution, in-situ curvature measurement set-up during Pd deposition, annealing and hydriding. This set-up allowed producing Pd thin films with similar internal stress levels but significantly different microstructures. This was evidenced from detailed defect statistics obtained by transmission electron microscopy, which showed that the densities of grain boundaries, dislocations and twin boundaries have all been lowered by annealing. The same set-up was then used to study the hydriding equilibrium and kinetic behaviour of the resulting films at room temperature. A full quantitative analysis of their hydriding cycles showed that the rate constants of both the adsorption- and absorption-limited kinetic regimes were strongly affected by microstructure. Defect engineering was thereby shown to increase the rate constants for hydrogen adsorption and absorption in Pd by a factor 40 and 30, respectively. Copyright (C) 2015, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
|
|
Language |
|
Wos |
000355884300012 |
Publication Date |
2015-05-02 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0360-3199; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
3.582 |
Times cited |
13 |
Open Access |
|
|
|
Notes |
Iap 7/21 |
Approved |
Most recent IF: 3.582; 2015 IF: 3.313 |
|
|
Call Number |
c:irua:126429 |
Serial |
838 |
|
Permanent link to this record |
|
|
|
|
Author |
Wee, L.H.; Meledina, M.; Turner, S.; Custers, K.; Kerkhofs, S.; Van Tendeloo, G.; Martens, J.A. |
|
|
Title |
Hematite iron oxide nanorod patterning inside COK-12 mesochannels as an efficient visible light photocatalyst |
Type |
A1 Journal article |
|
Year |
2015 |
Publication |
Journal of materials chemistry A : materials for energy and sustainability |
Abbreviated Journal |
J Mater Chem A |
|
|
Volume |
3 |
Issue |
3 |
Pages |
19884-19891 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
|
Abstract |
The uniform dispersion of functional oxide nanoparticles on the walls of ordered mesoporous silica to tailor optical, electronic, and magnetic properties for biomedical and environmental applications is a scientific challenge. Here, we demonstrate homogeneous confined growth of 5 nanometer-sized hematite iron oxide (α-Fe2O3) inside mesochannels of ordered mesoporous COK-12 nanoplates. The three-dimensional inclusion of the α-Fe2O3 nanorods in COK-12 particles is studied using high-angle annular dark field scanning transmission electron microscopy (HAADF-STEM), energy-dispersive X-ray (EDX) spectroscopy and electron tomography. High resolution imaging and EDX spectroscopy provide information about the particle size, shape and crystal phase of the loaded α-Fe2O3 material, while electron tomography provides detailed information on the spreading of the nanorods throughout the COK-12 host. This nanocomposite material, having a semiconductor band gap energy of 2.40 eV according to diffuse reflectance spectroscopy, demonstrates an improved visible light photocatalytic degradation activity with rhodamine 6G and 1-adamantanol model compounds. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000362041300033 |
Publication Date |
2015-08-26 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2050-7488;2050-7496; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
8.867 |
Times cited |
9 |
Open Access |
|
|
|
Notes |
L.H.W. and S.T. thank the FWO-Vlaanderen for a postdoctoral research fellowship (12M1415N) and under contract number G004613N . J.A.M gratefully acknowledge financial supports from Flemish Government (Long-term structural funding-Methusalem). Collaboration among universities was supported by the Belgian Government (IAP-PAI network). |
Approved |
Most recent IF: 8.867; 2015 IF: 7.443 |
|
|
Call Number |
c:irua:132567 |
Serial |
3959 |
|
Permanent link to this record |
|
|
|
|
Author |
Deng, S.; Kurttepeli, M.; Cott, D.J.; Bals, S.; Detavernier, C. |
|
|
Title |
Porous nanostructured metal oxides synthesized through atomic layer deposition on a carbonaceous template followed by calcination |
Type |
A1 Journal article |
|
Year |
2015 |
Publication |
Journal of materials chemistry A : materials for energy and sustainability |
Abbreviated Journal |
J Mater Chem A |
|
|
Volume |
3 |
Issue |
3 |
Pages |
2642-2649 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
|
Abstract |
Porous metal oxides with nano-sized features attracted intensive interest in recent decades due to their high surface area which is essential for many applications, e.g. Li ion batteries, photocatalysts, fuel cells and dye-sensitized solar cells. Various approaches have so far been investigated to synthesize porous nanostructured metal oxides, including self-assembly and template-assisted synthesis. For the latter approach, forests of carbon nanotubes are considered as particularly promising templates, with respect to their one-dimensional nature and the resulting high surface area. In this work, we systematically investigate the formation of porous metal oxides (Al2O3, TiO2, V2O5 and ZnO) with different morphologies using atomic layer deposition on multi-walled carbon nanotubes followed by post-deposition calcination. X-ray diffraction, scanning electron microscopy accompanied by X-ray energy dispersive spectroscopy and transmission electron microscopy were used for the investigation of morphological and structural transitions at the micro- and nano-scale during the calcination process. The crystallization temperature and the surface coverage of the metal oxides and the oxidation temperature of the carbon nanotubes were found to produce significant influence on the final morphology. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
Cambridge |
Editor |
|
|
|
Language |
|
Wos |
000348990500019 |
Publication Date |
2014-12-06 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2050-7488;2050-7496; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
8.867 |
Times cited |
23 |
Open Access |
OpenAccess |
|
|
Notes |
Fwo; 239865 Cocoon; 335078 Colouratoms; ECAS_Sara; (ROMEO:yellow; preprint:; postprint:restricted ; pdfversion:cannot); |
Approved |
Most recent IF: 8.867; 2015 IF: 7.443 |
|
|
Call Number |
c:irua:125298 |
Serial |
2673 |
|
Permanent link to this record |
|
|
|
|
Author |
Van Havenbergh, K.; Turner, S.; Driesen, K.; Bridel, J.-S.; Van Tendeloo, G. |
|
|
Title |
Solidelectrolyte interphase evolution of carbon-coated silicon nanoparticles for lithium-ion batteries monitored by transmission electron microscopy and impedance spectroscopy |
Type |
A1 Journal article |
|
Year |
2015 |
Publication |
Energy technology |
Abbreviated Journal |
Energy Technol-Ger |
|
|
Volume |
3 |
Issue |
3 |
Pages |
699-708 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
|
Abstract |
The main drawbacks of silicon as the most promising anode material for lithium-ion batteries (theoretical capacity=3572 mAh g−1) are lithiation-induced volume changes and the continuous formation of a solidelectrolyte interphase (SEI) upon cycling. A recent strategy is to focus on the influence of coatings and composite materials. To this end, the evolution of the SEI, as well as an applied carbon coating, on nanosilicon electrodes during the first electrochemical cycles is monitored. Two specific techniques are combined: Transmission Electron Microscopy (TEM) is used to study the surface evolution of the nanoparticles on a very local scale, whereas electrochemical impedance spectroscopy (EIS) provides information on the electrode level. A TEMEELS fingerprint signal of carbonate structures from the SEI is discovered, which can be used to differentiate between the SEI and a graphitic carbon matrix. Furthermore, the shielding effect of the carbon coating and the thickness evolution of the SEI are described. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000357869100003 |
Publication Date |
2015-06-24 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2194-4288; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.789 |
Times cited |
|
Open Access |
|
|
|
Notes |
IWT Flanders |
Approved |
Most recent IF: 2.789; 2015 IF: 2.824 |
|
|
Call Number |
c:irua:126676 |
Serial |
3051 |
|
Permanent link to this record |
|
|
|
|
Author |
Zalfani, M.; van der Schueren, B.; Hu, Z.-Y.; Rooke, J.C.; Bourguiga, R.; Wu, M.; Li, Y.; Van Tendeloo, G.; Su, B.-L. |
|
|
Title |
Novel 3DOM BiVO4/TiO2nanocomposites for highly enhanced photocatalytic activity |
Type |
A1 Journal article |
|
Year |
2015 |
Publication |
Journal of materials chemistry A : materials for energy and sustainability |
Abbreviated Journal |
J Mater Chem A |
|
|
Volume |
3 |
Issue |
3 |
Pages |
21244-21256 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
|
Abstract |
Novel 3DOM BiVO4/TiO2 nanocomposites with intimate contact were for the first time synthesized by a hydrothermal method in order to elucidate their visible-light-driven photocatalytic performances. BiVO4 nanoparticles and 3DOM TiO2 inverse opal were fabricated respectively. These materials were characterized by XRD, XPS, SEM, TEM, N2 adsorption–desorption and UV-vis diffuse (UV-vis) and photoluminescence spectroscopies. As references for comparison, a physical mixture of BiVO4 nanoparticles and 3DOM TiO2 inverse opal powder (0.08 : 1), and a BiVO4/P25 TiO2 (0.08 : 1) nanocomposite made also by the hydrothermal method were prepared. The photocatalytic performance of all the prepared materials was evaluated by the degradation of rhodamine B (RhB) as a model pollutant molecule under visible light irradiation. The highly ordered 3D macroporous inverse opal structure can provide more active surface areas and increased mass transfer because of its highly accessible 3D porosity. The results show that 3DOM BiVO4/TiO2 nanocomposites possess a highly prolonged lifetime and increased separation of visible light generated charges and extraordinarily high photocatalytic activity. Owing to the intimate contact between BiVO4 and large surface area 3DOM TiO2, the photogenerated high energy charges can be easily transferred from BiVO4 to the 3DOM TiO2 support. BiVO4 nanoparticles in the 3DOM TiO2 inverse opal structure act thus as a sensitizer to absorb visible light and to transfer efficiently high energy electrons to TiO2 to ensure long lifetime of the photogenerated charges and keep them well separated, owing to the direct band gap of BiVO4 of 2.4 eV, favourably positioned band edges, very low recombination rate of electron–hole pairs and stability when coupled with photocatalysts, explaining the extraordinarily high photocatalytic performance of 3DOM BiVO4/TiO2 nanocomposites. It is found that larger the amount of BiVO4 in the nanocomposite, longer the duration of photogenerated charge separation and higher the photocatalytic activity. This work can shed light on the development of novel visible light responsive nanomaterials for efficient solar energy utilisation by the intimate combination of an inorganic light sensitizing nanoparticle with an inverse opal structure with high diffusion efficiency and high accessible surface area. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000363163200049 |
Publication Date |
2015-09-08 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2050-7488;2050-7496; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
8.867 |
Times cited |
88 |
Open Access |
|
|
|
Notes |
This work was realized with the financial support of the Belgian FNRS (Fonds National de la Recherche Scientifique). This research used resources of the Electron Microscopy Service located at the University of Namur. This Service is a member of the “Plateforme Technologique Morphologie – Imagerie”. The XPS analyses were made in the LISE, Department of Physics of the University of Namur thanks to Dr P. Louette. This work was also supported by Changjiang Scholars and the Innovative Research Team (IRT1169) of the Ministry of Education of the People's Republic of China. B. L. Su acknowledges the Chinese Central Government for an “Expert of the State” position in the Program of the “Thousand Talents” and a Clare Hall Life Membership at the Clare Hall and the financial support of the Department of Chemistry, University of Cambridge. G. Van Tendeloo and Z. Y. Hu acknowledge support from the EC Framework 7 program ESTEEM2 (Reference 312483).; esteem2_jra4 |
Approved |
Most recent IF: 8.867; 2015 IF: 7.443 |
|
|
Call Number |
c:irua:129476 c:irua:129476 |
Serial |
3951 |
|
Permanent link to this record |
|
|
|
|
Author |
van Laer, K.; Bogaerts, A. |
|
|
Title |
Improving the Conversion and Energy Efficiency of Carbon Dioxide Splitting in a Zirconia-Packed Dielectric Barrier Discharge Reactor |
Type |
A1 Journal article |
|
Year |
2015 |
Publication |
Energy technology |
Abbreviated Journal |
Energy Technol-Ger |
|
|
Volume |
3 |
Issue |
3 |
Pages |
1038-1044 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
|
|
Abstract |
The use of plasma technology for CO2 splitting is gaining increasing interest, but one of the major obstacles to date for industrial implementation is the considerable energy cost. We demonstrate that the introduction of a packing of dielectric zirconia (ZrO2) beads into a dielectric barrier discharge (DBD) plasma reactor can enhance the CO2 conversion and energy efficiency up to a factor 1.9 and 2.2, respectively, compared to that in a normal (unpacked) DBD reactor. We obtained a maximum conversion of 42 % and a maximum energy efficiency of 9.6 %. However, it is the ability of the packing to almost double both the conversion and the energy efficiency simultaneously at certain input parameters that makes it very promising. The improved conversion and energy efficiency can be explained by the higher values of the local electric field and electron energy near the contact points of the beads and the lower breakdown voltage, demonstrated by 2 D fluid modeling. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000362913600006 |
Publication Date |
2015-08-19 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2194-4288 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.789 |
Times cited |
59 |
Open Access |
|
|
|
Notes |
This research was carried out in the framework of the network on Physical Chemistry of Plasma-Surface Interactions—Interuniversity Attraction Poles, phase VII (http://psiiap7.ulb.ac.be/), and supported by the Belgian Science Policy Office (BELSPO). K.V.L. is indebted to the Institute for the Promotion of Innovation by Science and Technology in Flanders (IWT Flanders) for financial support |
Approved |
Most recent IF: 2.789; 2015 IF: 2.824 |
|
|
Call Number |
c:irua:128224 |
Serial |
3992 |
|
Permanent link to this record |
|
|
|
|
Author |
Lander, L.; Rousse, G.; Abakumov, A.M.; Sougrati, M.; Van Tendeloo, G.; Tarascon, J.-M. |
|
|
Title |
Structural, electrochemical and magnetic properties of a novel KFeSO4F polymorph |
Type |
A1 Journal article |
|
Year |
2015 |
Publication |
Journal of materials chemistry A : materials for energy and sustainability |
Abbreviated Journal |
J Mater Chem A |
|
|
Volume |
3 |
Issue |
3 |
Pages |
19754-19764 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
|
Abstract |
In the quest for sustainable and low-cost positive electrode materials for Li-ion batteries, we discovered, as reported herein, a new low temperature polymorph of KFeSO4F. Contrary to the high temperature phase crystallizing in a KTiOPO4-like structure, this new phase adopts a complex layer-like structure built on FeO4F2 octahedra and SO4 tetrahedra, with potassium cations located in between the layers, as solved using neutron and synchrotron diffraction experiments coupled with electron diffraction. The detailed analysis of the structure reveals an alternation of edge-and corner-shared FeO4F2 octahedra leading to a large monoclinic cell of 1771.774(7) angstrom(3). The potassium atoms are mobile within the structure as deduced by ionic conductivity measurements and confirmed by the bond valence energy landscape approach thus enabling a partial electrochemical removal of K+ and uptake of Li+ at an average potential of 3.7 V vs. Li+/Li-0. Finally, neutron diffraction experiments coupled with SQUID measurements reveal a long range antiferromagnetic ordering of the Fe2+ magnetic moments below 22 K with a possible magnetoelectric behavior. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
Cambridge |
Editor |
|
|
|
Language |
|
Wos |
000362041300018 |
Publication Date |
2015-08-17 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2050-7488; 2050-7496 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
8.867 |
Times cited |
11 |
Open Access |
|
|
|
Notes |
|
Approved |
Most recent IF: 8.867; 2015 IF: 7.443 |
|
|
Call Number |
UA @ lucian @ c:irua:132566 |
Serial |
4253 |
|
Permanent link to this record |
|
|
|
|
Author |
De Schepper, E.; Van Passel, S.; Lizin, S. |
|
|
Title |
Economic benefits of combining clean energy technologies : the case of solar photovoltaics and battery electric vehicles |
Type |
A1 Journal article |
|
Year |
2015 |
Publication |
International Journal Of Energy Research |
Abbreviated Journal |
Int J Energ Res |
|
|
Volume |
39 |
Issue |
8 |
Pages |
1109-1119 |
|
|
Keywords |
A1 Journal article; Economics; Engineering sciences. Technology; Engineering Management (ENM) |
|
|
Abstract |
The combined use of clean technologies can lead amongst other benefits to reduced environmental impacts, improved system efficiencies, better management of land scarcity, and diminishment of the effect of power variability of intermittent clean energy sources. Nonetheless, private investors facing budgetary constraints will only opt to invest in the combination of technologies if the latter is more profitable than the investment in a single technology. The aim of the paper is to provide a systematic model for decision makers that allows them to evaluate the profitability of any random combination of technologies under budgetary constraints, and to compare this profitability with that of the individual projects in isolation. This research goes beyond the state of art in the field of financial management and more specifically in the field of the rationing of capital amongst interdependent projects, by developing a method to calculate the payoff of interdependent projects undertaken together. Moreover, this paper develops a computational model from the investor's point of view, of which the purpose is threefold: First, the model allows to directly compare the economic payoff of individual complementary technologies with the economic payoff of their integrated combination, under budgetary constraints. Second, the model calculates economic synergies labeled benefits of combined technologies' (BOCT) when combining complementary technologies. Third, the model explains the rationalization behind the presence of BOCT. The model exemplifies an ex ante cost benefit analysis developed for business and non-governmental use. A four step methodology is proposed and illustrated by means of a case study of PV solar power and battery electric vehicles (BEVs) for a small Belgian enterprise. Results show that at low electricity prices (<Euro0.112/kWh) it is most profitable to invest in BEVs. When the price of electricity rises (>Euro0.134/kWh), investment in exclusively PV becomes most attractive. In all other cases, it is more profitable to invest in the combination of both technologies. Copyright (c) 2015 John Wiley & Sons, Ltd. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000355732200006 |
Publication Date |
2015-03-21 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0363-907x |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
2.598 |
Times cited |
14 |
Open Access |
|
|
|
Notes |
; Sebastien Lizin would like to thank the Research Foundation Flanders (FWO), grant number 12G5415N, for their funding without which it would have been impossible to review this work. ; |
Approved |
Most recent IF: 2.598; 2015 IF: 2.418 |
|
|
Call Number |
UA @ admin @ c:irua:127535 |
Serial |
6188 |
|
Permanent link to this record |
|
|
|
|
Author |
Reynaud, M.; Rousse, G.; Abakumov, A.M.; Sougrati, M.T.; Van Tendeloo, G.; Chotard, J.-N.; Tarascon, J.-M. |
|
|
Title |
Design of new electrode materials for Li-ion and Na-ion batteries from the bloedite mineral Na2Mg(SO4)2\cdot4H2O |
Type |
A1 Journal article |
|
Year |
2014 |
Publication |
Journal of materials chemistry A : materials for energy and sustainability |
Abbreviated Journal |
J Mater Chem A |
|
|
Volume |
2 |
Issue |
8 |
Pages |
2671-2680 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
|
Abstract |
Mineralogy offers a large database to search for Li- or Na-based compounds having suitable structural features for acting as electrode materials, LiFePO4 being one example. Here we further explore this avenue and report on the electrochemical properties of the bloedite type compounds Na2M(SO4)(2)center dot 4H(2)O (M = Mg, Fe, Co, Ni, Zn) and their dehydrated phases Na2M(SO4)(2) (M = Fe, Co), whose structures have been solved via complementary synchrotron X-ray diffraction, neutron powder diffraction and transmission electron microscopy. Among these compounds, the hydrated and anhydrous iron-based phases show electrochemical activity with the reversible release/uptake of 1 Na+ or 1 Li+ at high voltages of similar to 3.3 V vs. Na+/Na-0 and similar to 3.6 V vs. Li+/Li-0, respectively. Although the reversible capacities remain lower than 100 mA h g(-1), we hope this work will stress further the importance of mineralogy as a source of inspiration for designing eco-efficient electrode materials. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
Cambridge |
Editor |
|
|
|
Language |
|
Wos |
000331247500031 |
Publication Date |
2013-11-22 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2050-7488;2050-7496; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
8.867 |
Times cited |
56 |
Open Access |
|
|
|
Notes |
|
Approved |
Most recent IF: 8.867; 2014 IF: 7.443 |
|
|
Call Number |
UA @ lucian @ c:irua:115807 |
Serial |
659 |
|
Permanent link to this record |
|
|
|
|
Author |
Pasquini, L.; Sacchi, M.; Brighi, M.; Boelsma, C.; Bals, S.; Perkisas, T.; Dam, B. |
|
|
Title |
Hydride destabilization in core-shell nanoparticles |
Type |
A1 Journal article |
|
Year |
2014 |
Publication |
International journal of hydrogen energy |
Abbreviated Journal |
Int J Hydrogen Energ |
|
|
Volume |
39 |
Issue |
5 |
Pages |
2115-2123 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
|
Abstract |
We present a model that describes the effect of elastic constraint on the thermodynamics of hydrogen absorption and desorption in biphasic core-shell nanoparticles, where the core is a hydride forming metal. In particular, the change of the hydride formation enthalpy and of the equilibrium pressure for the metal/hydride transformation are described as a function of nanoparticles radius, shell thickness, and elastic properties of both core and shell. To test the model, the hydrogen sorption isotherms of Mg-MgO core-shell nanoparticles, synthesized by inert gas condensation, were measured by means of optical hydrogenography. The model's predictions are in good agreement with the experimentally determined plateau pressure of hydrogen absorption. The features that a core-shell systems should exhibit in view of practical hydrogen storage applications are discussed with reference to the model and the experimental results. Copyright (C) 2013, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
|
|
Language |
|
Wos |
000331344800022 |
Publication Date |
2014-01-04 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0360-3199; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
3.582 |
Times cited |
32 |
Open Access |
Not_Open_Access |
|
|
Notes |
COST Action MP1103 |
Approved |
Most recent IF: 3.582; 2014 IF: 3.313 |
|
|
Call Number |
UA @ lucian @ c:irua:115785 |
Serial |
1528 |
|
Permanent link to this record |
|
|
|
|
Author |
Ying, J.; Yang, X.-Y.; Hu, Z.-Y.; Mu, S.-C.; Janiak, C.; Geng, W.; Pan, M.; Ke, X.; Van Tendeloo, G.; Su, B.-L. |
|
|
Title |
One particle@one cell : highly monodispersed PtPd bimetallic nanoparticles for enhanced oxygen reduction reaction |
Type |
A1 Journal article |
|
Year |
2014 |
Publication |
Nano energy |
Abbreviated Journal |
Nano Energy |
|
|
Volume |
8 |
Issue |
|
Pages |
214-222 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
|
Abstract |
Highly monodispersed platinum-based nanoalloys are the best-known catalysts for the oxygen reduction reaction. Although certainly promising, the durability and stability are among the main requirements for commercializing fuel cell electrocatalysts in practical applications. Herein, we synthesize highly stable, durable and catalytic active monodispersed PtPd nano-particles encapsulated in a unique one particle@one cell structure by adjusting the viscosity of solvents using mesocellular foam. PtPd nanoparticles in mesocellular carbon foam exhibit an excellent electrocatalytic activity (over 4 times mass and specific activities than the commercial Pt/C catalyst). Most importantly, this nanocatalyst shows no obvious change of structure and only a 29.5% loss in electrochemically active surface area after 5000 potential sweeps between 0.6 and 1.1 V versus reversible hydrogen electrode cycles. (C) 2014 Elsevier Ltd. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000340981700026 |
Publication Date |
2014-06-23 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
2211-2855; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
12.343 |
Times cited |
40 |
Open Access |
|
|
|
Notes |
|
Approved |
Most recent IF: 12.343; 2014 IF: 10.325 |
|
|
Call Number |
UA @ lucian @ c:irua:119255 |
Serial |
2465 |
|
Permanent link to this record |
|
|
|
|
Author |
Gaouyat, L.; He, Z.; Colomer, J.-F.; Lambin, P.; Mirabella, F.; Schryvers, D.; Deparis, O. |
|
|
Title |
Revealing the innermost nanostructure of sputtered NiCrOx solar absorber cermets |
Type |
A1 Journal article |
|
Year |
2014 |
Publication |
Solar energy materials and solar cells |
Abbreviated Journal |
Sol Energ Mat Sol C |
|
|
Volume |
122 |
Issue |
|
Pages |
303-308 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
|
Abstract |
Conversion of solar energy into thermal energy helps reducing consumption of non-renewable energies. Cermets (ceramicmetal composites) are versatile materials suitable, amongst other applications, for solar selective absorbers. Although the presence of metallic Ni particles in the dielectric matrix is a prerequisite for efficient solar selective absorption in NiCrOx cermets, no clear evidence of such particles is reported so far. By combining comprehensive chemical and structural analyses, we reveal the presumed nanostructure which is at the origin of the remarkable optical properties of this cermet material. Using sputtered NiCrOx layers in a solar absorber multilayer stack on aluminium substrate allows us to achieve solar absorptance as high as α=96.1% while keeping thermal emissivity as low as ε=2.2%, both values being comparable to best values recorded so far. With the nanostructure of sputtered NiCrOx cermets eventually revealed, further optimization of solar absorbers can be anticipated and technological exploitation of cermet materials in other applications can be foreseen. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
Amsterdam |
Editor |
|
|
|
Language |
|
Wos |
000331494200040 |
Publication Date |
2013-11-12 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0927-0248; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
4.784 |
Times cited |
12 |
Open Access |
|
|
|
Notes |
|
Approved |
Most recent IF: 4.784; 2014 IF: 5.337 |
|
|
Call Number |
UA @ lucian @ c:irua:113086 |
Serial |
2902 |
|
Permanent link to this record |
|
|
|
|
Author |
Mooij, L.; Perkisas, T.; Palsson, G.; Schreuders, H.; Wolff, M.; Hjorvarsson, B.; Bals, S.; Dam, B. |
|
|
Title |
The effect of microstructure on the hydrogenation of Mg/Fe thin film multilayers |
Type |
A1 Journal article |
|
Year |
2014 |
Publication |
International journal of hydrogen energy |
Abbreviated Journal |
Int J Hydrogen Energ |
|
|
Volume |
39 |
Issue |
30 |
Pages |
17092-17103 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT) |
|
|
Abstract |
Nanoconfined magnesium hydride can be simultaneously protected and thermodynamically destabilized when interfaced with materials such as Ti and Fe. We study the hydrogenation of thin layers of Mg (<14 nm) nanoconfined in one dimension within thin film Fe/Mg/Fe/Pd multilayers by the optical technique Hydrogenography. The hydrogenation of nanosized magnesium layers in Fe/Mg/Fe multilayers surprisingly shows the presence of multiple plateau pressures, whose nature is thickness dependent. In contrast, hydrogen desorption occurs via a single plateau which does not depend on the Mg layer thickness. From structural and morphological analyses with X-ray diffraction/reflectometry and cross-section TEM, we find that the Mg layer roughness is large when deposited on Fe and furthermore contains high-angle grain boundaries (GB's). When grown on Ti, the Mg layer roughness is low and no high-angle GB's are detected. From a Ti/Mg/Fe multilayer, in which the Mg layer is flat and has little or no GB's, we conclude that MgH2 is indeed destabilized by the interface with Fe. In this case, both the ab- and desorption plateau pressures are increased by a factor two compared to the hydrogenation of Mg within Ti/Mg/Ti multilayers. We hypothesize that the GB's in the Fe/Mg/Fe multilayer act as diffusion pathways for Pd, which is known to greatly alter the hydrogenation behavior of Mg when the two materials share an interface. Copyright (C) 2014, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
|
|
Language |
|
Wos |
000343839000031 |
Publication Date |
2014-09-10 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0360-3199; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
3.582 |
Times cited |
15 |
Open Access |
Not_Open_Access |
|
|
Notes |
COST Action MP1103 |
Approved |
Most recent IF: 3.582; 2014 IF: 3.313 |
|
|
Call Number |
UA @ lucian @ c:irua:121175 |
Serial |
3575 |
|
Permanent link to this record |
|
|
|
|
Author |
Vanschoenwinkel, J.; Lizin, S.; Swinnen, G.; Azadi, H.; Van Passel, S. |
|
|
Title |
Solar cooking in Senegalese villages : an application of best-worst scaling |
Type |
A1 Journal article |
|
Year |
2014 |
Publication |
Energy Policy |
Abbreviated Journal |
Energ Policy |
|
|
Volume |
67 |
Issue |
|
Pages |
447-458 |
|
|
Keywords |
A1 Journal article; Sociology; Engineering sciences. Technology; Engineering Management (ENM) |
|
|
Abstract |
Dissemination programs of nontraditional cookstoves often fail. Nontraditional cookstoves aim to solve problems associated with biomass fuel usage in developing countries. Recent studies do not explain what drives user's cookstove choice. This study therefore builds a holistic framework that centralizes product-specific preferences or needs. The case study identifies product-specific factors that influence rural Senegalese inhabitants to switch to solar cooking, using best worst scaling. Looking at the preferences, the case study classified 126 respondents, in three distinct market segments with different solar cooking expectations. The paper identifies socio-demographic characteristics that explain these differences in the respondents' preferences. Finally, the respondent sample is divided in two groups: solar cooker owners and non-owners. When studied with regard to the same issue, solar cooker owners appear to value benefits of the solar cooker lower than non-owners. This is due to program factors (such as formations, after-sales network) and miscommunication (such as a wrong image of the solar cooker) that highly influenced the respondents' cookstove choice. As a conclusion, solar cookers and solar cooking programs are not always adapted to the needs and requirements of the end-users. Needs-oriented and end-user adopted strategies are necessary in order to successfully implement nontraditional cookstoves programs. (C) 2013 Elsevier Ltd. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000332815300043 |
Publication Date |
2014-01-08 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0301-4215; 1873-6777 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
4.14 |
Times cited |
10 |
Open Access |
|
|
|
Notes |
; The authors thank the VLIR-UOS for their financial support and the Sol Suffit Program for their co-operation during the research. ; |
Approved |
Most recent IF: 4.14; 2014 IF: 2.575 |
|
|
Call Number |
UA @ admin @ c:irua:127544 |
Serial |
6251 |
|
Permanent link to this record |
|
|
|
|
Author |
Snoeckx, R.; Setareh, M.; Aerts, R.; Simon, P.; Maghari, A.; Bogaerts, A. |
|
|
Title |
Influence of N2 concentration in a CH4/N2 dielectric barrier discharge used for CH4 conversion into H2 |
Type |
A1 Journal article |
|
Year |
2013 |
Publication |
International journal of hydrogen energy |
Abbreviated Journal |
Int J Hydrogen Energ |
|
|
Volume |
38 |
Issue |
36 |
Pages |
16098-16120 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT) |
|
|
Abstract |
We present a combined study of experimental and computational work for a dielectric barrier discharge (DBD) used for CH4 conversion into H2. More specifically, we investigated the influence of N2 as an impurity (150,000 ppm) and as additive gas (199%) on the CH4 conversion and H2 yield. For this purpose, a zero-dimensional chemical kinetics model is applied to study the plasma chemistry. The calculated conversions and yields for various gas mixing ratios are compared to the obtained experimental values, and good agreement is achieved. The study reveals the significance of the View the MathML source and View the MathML source metastable states for the CH4 conversion into H2, based on a kinetic analysis of the reaction chemistry. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
Oxford |
Editor |
|
|
|
Language |
|
Wos |
000327904500027 |
Publication Date |
2013-10-23 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0360-3199; |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
3.582 |
Times cited |
40 |
Open Access |
|
|
|
Notes |
|
Approved |
Most recent IF: 3.582; 2013 IF: 2.930 |
|
|
Call Number |
UA @ lucian @ c:irua:111372 |
Serial |
1642 |
|
Permanent link to this record |
|
|
|
|
Author |
L. Zhang, J. Kim, J. Zhang, F. Nan, N. Gauquelin, G.A. Botton, P. He, R. Bashyam, S. Knights |
|
|
Title |
Ti4O7 supported Ru@Pt core–shell catalyst for CO-tolerance in PEM fuel cell hydrogen oxidation reaction |
Type |
A1 Journal Article |
|
Year |
2013 |
Publication |
Applied Energy |
Abbreviated Journal |
|
|
|
Volume |
103 |
Issue |
March 2013 |
Pages |
507-513 |
|
|
Keywords |
A1 Journal Article; Electron Microscopy for Materials Science (EMAT) ; |
|
|
Abstract |
A new method is developed for synthesizing Ti4O7 supported Ru@Pt core–shell catalyst (Ru@Pt/Ti4O7) through pyrolysis followed by microwave irradiation. The purpose is to improve the Ru durability of PtRu from core–shell structure and strong bonding to Ti4O7 oxide. In this method, the first step is to co-reduce the mixture of ruthenium precursor and TiO2 in a H2 reducing atmosphere under heat-treatment to obtain a Ru core on Ti4O7 support, and the second step is to create a shell of platinum via microwave irradiation. Energy dispersive X-ray spectrometry, X-ray Diffraction, High-resolution Scanning Transmission Electron Microscopy with the high-angle annular dark-field method and Electron Energy-Loss Spectroscopy are used to demonstrate that this catalyst with larger particles has a core–shell structure with a Ru core and a Pt shell. Electrochemical measurements show Ru@Pt/Ti4O7 catalyst has a higher CO-tolerance capability than that of PtRu/C alloy catalyst. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000314669500048 |
Publication Date |
2012-11-11 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
|
ISBN |
|
Additional Links |
|
|
|
Impact Factor |
|
Times cited |
33 |
Open Access |
|
|
|
Notes |
|
Approved |
Most recent IF: NA |
|
|
Call Number |
EMAT @ emat @ |
Serial |
4547 |
|
Permanent link to this record |
|
|
|
|
Author |
Lizin, S.; Van Passel, S.; De Schepper, E.; Maes, W.; Lutsen, L.; Manca, J.; Vanderzande, D. |
|
|
Title |
Life cycle analyses of organic photovoltaics : a review |
Type |
A1 Journal article |
|
Year |
2013 |
Publication |
Energy & Environmental Science |
Abbreviated Journal |
Energ Environ Sci |
|
|
Volume |
6 |
Issue |
11 |
Pages |
3136-3149 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM) |
|
|
Abstract |
This paper reviews the available life cycle analysis (LCA) literature on organic photovoltaics (OPVs). This branch of OPV research has focused on the environmental impact of single-junction bulk heterojunction polymer solar cells using a P3HT/PC60BM active layer blend processed on semi-industrial pilot lines in ambient surroundings. The environmental impact was found to be strongly decreasing through continuous innovation of the manufacturing procedures. The current top performing cell regarding environmental performance has a cumulative energy demand of 37.58 MJp m(-2) and an energy payback time in the order of months for cells having 2% efficiency, thereby rendering OPV cells one of the best performing PV technologies from an environmental point of view. Nevertheless, we find that LCA literature is lagging behind on the main body of OPV literature due to the lack of readily available input data. Still, LCA research has led us to believe that in the quest for higher efficiencies, environmental sustainability is being disregarded on the materials' side. Hence, we advise the scientific community to take the progress made on environmental sustainability aspects of OPV preparations into account not only because standard procedures put a bigger strain on the environment, but also because these methods may not be transferrable to an industrial process. Consequently, we recommend policy makers to subsidize research that bridges the gaps between fundamental materials research, stability, and scalability given that these constraints have to be fulfilled simultaneously if OPVs are ever to be successful on the market. Additionally, environmental sustainability will have to keep on being monitored to steer future developments in the right direction. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000325946400002 |
Publication Date |
2013-10-11 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
1754-5692; 1754-5706 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
29.518 |
Times cited |
124 |
Open Access |
|
|
|
Notes |
; The authors are much obliged to both the INTERREG ORGAN-EXT project and FP7 MOLESOL project for their financial support, without which it would have been impossible to conduct this research. ; |
Approved |
Most recent IF: 29.518; 2013 IF: 15.490 |
|
|
Call Number |
UA @ admin @ c:irua:127548 |
Serial |
6223 |
|
Permanent link to this record |
|
|
|
|
Author |
Van Dael, M.; Van Passel, S.; Pelkmans, L.; Guisson, R.; Reumermann, P.; Luzardo, N.M.; Witters, N.; Broeze, J. |
|
|
Title |
A techno-economic evaluation of a biomass energy conversion park |
Type |
A1 Journal article |
|
Year |
2013 |
Publication |
Applied Energy |
Abbreviated Journal |
Appl Energ |
|
|
Volume |
104 |
Issue |
|
Pages |
611-622 |
|
|
Keywords |
A1 Journal article; Engineering sciences. Technology; Engineering Management (ENM) |
|
|
Abstract |
Biomass as a renewable energy source has many advantages and is therefore recognized as one of the main renewable energy sources to be deployed in order to attain the target of 20% renewable energy use of final energy consumption by 2020 in Europe. In this paper the concept of a biomass Energy Conversion Park (ECP) is introduced. A biomass ECP can be defined as a synergetic, multi-dimensional biomass conversion site with a highly integrated set of conversion technologies in which a multitude of regionally available biomass (residue) sources are converted into energy and materials. A techno-economic assessment is performed on a case study in the Netherlands to illustrate the concept and to comparatively assess the highly integrated system with two mono-dimensional models. The three evaluated models consist of (1) digestion of the organic fraction of municipal solid waste, (2) co-digestion of manure and co-substrates, and (3) integration. From a socio-economic point of view it can be concluded that it is economically and energetically more interesting to invest in the integrated model than in two separate models. The integration is economically feasible and environmental benefits can be realized. For example, the integrated model allows the implementation of a co-digester. Unmanaged manure would otherwise represent a constant pollution risk. However, from an investor's standpoint one should firstly invest in the municipal solid waste digester since the net present value (NPV) of this mono-dimensional model is higher than that of the multi-dimensional model. A sensitivity analysis is performed to identify the most influencing parameters. Our results are of interest for companies involved in the conversion of biomass. The conclusions are useful for policy makers when deciding on policy instruments concerning manure processing or biogas production. (C) 2012 Elsevier Ltd. All rights reserved. |
|
|
Address |
|
|
|
Corporate Author |
|
Thesis |
|
|
|
Publisher |
|
Place of Publication |
|
Editor |
|
|
|
Language |
|
Wos |
000316152700062 |
Publication Date |
2012-12-25 |
|
|
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
|
Series Volume |
|
Series Issue |
|
Edition |
|
|
|
ISSN |
0306-2619 |
ISBN |
|
Additional Links |
UA library record; WoS full record; WoS citing articles |
|
|
Impact Factor |
7.182 |
Times cited |
45 |
Open Access |
|
|
|
Notes |
; We would like to thank the editor and the anonymous referees for their helpful suggestions and insightful comments that have significantly improved the paper. Furthermore, the authors gratefully acknowledge the financial support from INTERREG and the province of Limburg (Belgium). Also, we would like to thank all remaining partners of the ECP project (Eloi Schreurs, Dries Maes, Kristian Coppoolse, Han ten Berge, Bert Annevelink, Nathalie Devriendt, Erwin Cornelissen, Hannes Pieper, Pieter Vollaard, Jan Venselaar, and Hessel Abbink Spaink) for their support and contributions. Finally, we would like to express our gratitude towards the organization of the eighth International Conference on Renewable Resources and Biorefineries in Toulouse (France) for giving us the opportunity to present and thereby fine-tune our work. ; |
Approved |
Most recent IF: 7.182; 2013 IF: 5.261 |
|
|
Call Number |
UA @ admin @ c:irua:127552 |
Serial |
6145 |
|
Permanent link to this record |