|
“Integrated poultry waste management by co-digestion with perennial grass : effects of mixing ratio, pretreatments, reaction temperature, and effluent recycle on biomethanation yield”. Phuttaro C, Krishnan S, Saritpongteeraka K, Charnnok B, Diels L, Chaiprapat S, Biochemical engineering journal 196, 108937 (2023). http://doi.org/10.1016/J.BEJ.2023.108937
Abstract: This work aims to enhance the efficiency of integrated poultry waste management in bio-circular-green economy by maximizing the co-digestion of chicken manure and its digestate-grown biomass. In a series of batch assays, Napier grass (NG) was mixed with chicken manure (CM) at various proportions (100:0, 80:20, 60:40, 50:50, 40:60, 20:80 and 0:100) to identify co-substrate synergism, followed by physiochemical conditioning (size reduction and ultrasonication) of NG before co-digestion. Results indicated that NG mix of at least 80% was required to gain a full methanation potential of the individual substrates; no synergistic ratio above unity was found. However, the combined effect of size reduction and sonication was found to markedly improve the cosubstrate's biodegradability by 88.7%. The findings were then used to run continuous co-digestion at various operating regimes. In optimal continuous co-digestion condition, NG particle size of 0.6-2.4 mm combined with sonication intensity at 1111 kJ/kgTS improved biomethanation yield as high as 106.3%. Sub-thermophilic digestion at 45 degrees C was shown to give a higher and more stable CH4 yield than at 55 degrees C. Finally, it was also found that recycling liquid effluent at 40% to replace freshwater in feed, although showed no significant difference in CH4 yield (& alpha; = 0.05), noticeably increased system buffer capacity. This optimized biodegradation regime could give co-digestion waste management a higher overall plant efficiency and economic return.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 3.9
DOI: 10.1016/J.BEJ.2023.108937
|
|
|
“Active site titration of immobilized beta-galactosidase for the determination of active enzymes”. Jochems P, Mueller T, Satyawali Y, Diels L, Dejonghe W, Hanefeld U, Biochemical engineering journal 93, 137 (2015). http://doi.org/10.1016/J.BEJ.2014.10.007
Abstract: In the present study, an active site titration method is demonstrated, to determine the amount of active enzyme (beta-galactosidase), immobilized on a support. Two types of supports were investigated, viz, amino acrylic resin and a mixed matrix membrane. Furthermore, 2',4'-dinitrophenyl 2-deoxy-2-fluoro-beta-D-galactopyranoside was used as an inhibitor for the active site titration of immobilized beta-galactosidase obtained from Kluyveromyces lactis. Using the active site titration, approximately 8.3 mg of active enzyme was found on 1 g of dried commercially available SPRIN imibond, which is an amino acrylic resin with covalently bound beta-galactosidase obtained from K. lactis. However, this method, in its present form, was not effective on the mixed matrix membranes due to the irreversible partial adsorption of the leaving group (2',4'-dinitrophenolate) by the membrane. This observation implied that it is important to investigate interactions between the support and the used inhibitor and leaving group. (C) 2014 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.BEJ.2014.10.007
|
|
|
“Airborne bacteria in the atmosphere : presence, purpose, and potential”. Smets W, Moretti S, Denys S, Lebeer S, Atmospheric environment : an international journal 139, 214 (2016). http://doi.org/10.1016/J.ATMOSENV.2016.05.038
Abstract: Numerous recent studies have highlighted that the types of bacteria present in the atmosphere often show predictable patterns across space and time. These patterns can be driven by differences in bacterial sources of the atmosphere and a wide range of environmental factors, including UV intensity, precipitation events, and humidity. The abundance of certain bacterial taxa is of interest, not only for their ability to mediate a range of chemical and physical processes in the atmosphere, such as cloud formation and ice nucleation, but also for their implications -both beneficial and detrimental-for human health. Consequently, the widespread importance of airborne bacteria has stimulated the search for their applicability. Improving air quality, modelling the dispersal of airborne bacteria (e.g. pathogens) and biotechnological purposes are already being explored. Nevertheless, many technological challenges still need to be overcome to fully understand the roles of airborne bacteria in our health and global ecosystems.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.ATMOSENV.2016.05.038
|
|
|
“A high-order model for accurately simulating the size distribution of ultrafine particles in a traffic tunnel”. Vos PEJ, Nikolova I, Janssen S, Atmospheric environment : an international journal 59, 415 (2012). http://doi.org/10.1016/J.ATMOSENV.2012.05.011
Abstract: We present a computational model for simulating the dispersion of traffic emitted particulate matter inside a road tunnel, with an emphasis on the number concentration of ultrafine particles (UFP). The model primarily calculates the size distribution of the particle number concentration at each location inside the tunnel. The proposed model differs from existing models in the sense that it uses a continuous representation of the size distribution based upon the high-order finite element method and that it solves the governing equations using the state-of-the-art discontinuous Galerkin method. Next to the traditional transport processes, the model also implements the most important aerosol transformation processes such as coagulation, condensation and dry deposition. It is shown that based upon parametrisations found in literature, the process of condensation in a traffic tunnel cannot properly be modelled. Therefore, we present a correction factor that allows for a better parametrisation. The adequate performance of the model is demonstrated by both a verification study and a validation study. For the verification we show that the discretisation error converges consistently while for the validation we compare the modelled results with a suitable set of data from a UFP measurement campaign in a Taiwanese traffic tunnel. The model is shown to correctly simulate the observed behaviour and by applying a statistical model evaluation we demonstrate that the proposed model meets widely accepted air quality model acceptance criteria. (C) 2012 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.ATMOSENV.2012.05.011
|
|
|
“Characterisation of hydrous ferric oxides derived from iron-rich groundwaters and their contribution to the suspended sediment of streams”. Baken S, Sjostedt C, Gustafsson JP, Seuntjens P, Desmet N, De Schutter J, Smolders E, Applied geochemistry 39, 59 (2013). http://doi.org/10.1016/J.APGEOCHEM.2013.09.013
Abstract: When Fe(II) bearing groundwaters surface in streams, particulate authigenic Fe-rich material is produced by oxidation. Such freshly precipitated Fe minerals may be transported as suspended sediment and have a profound impact on the fate of trace metals and nutrients in rivers. The objective of this study was to monitor changes in mineralogy and composition of authigenic material from its source to streams of increasing order. Groundwaters, surface waters, and suspended sediment in streams of different order were sampled in the Kleine Nete catchment (Belgium), a lowland with Fe-rich groundwaters (3.5-53.8 mg Fe/L; pH 6.3-6.9). Fresh authigenic material (>0.45 mu m) was produced by oxidising filtered (<0.45 mu m) groundwater and surface water. This material contained, on average, 44% Fe, and smaller concentrations of C, P, and Ca. Iron EXAFS (Extended X-ray Absorption Fine Structure) spectroscopy showed that the Fe was present as poorly crystalline hydrous ferric oxides with a structure similar to that of ferrihydrite. The Fe concentration in the suspended sediment samples decreased to 36-40% (stream order 2), and further to 18-26% (stream order 4 and 5). Conversely, the concentrations of organic C, Ca, Si, and trace metals increased with increasing stream order, suggesting mixing of authigenic material with suspended sediment from a different source. The Fe speciation in the suspended sediment was similar to that in fresh authigenic material, but more Fe-Fe interactions were observed, i.e. it was increasingly hydrolysed, suggesting ageing reactions. The suspended sediment in the streams of order 4 and 5 is estimated to contain between 31% and 59% of authigenic material, but more data are needed to refine this estimate. The authigenic material is an important sink for P in these streams which may alleviate the eutrophication risk in this catchment. (C) 2013 Elsevier Ltd. All rights reserved.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1016/J.APGEOCHEM.2013.09.013
|
|
|
“Photocatalysis assisted simultaneous carbon oxidation and NOx reduction”. Liao L, Heylen S, Sree SP, Vallaey B, Keulemans M, Lenaerts S, Roeffaers MBJ, Martens JA, Applied catalysis : B : environmental 202, 381 (2017). http://doi.org/10.1016/J.APCATB.2016.09.042
Abstract: Photocatalysis assisted oxidation of carbon black was performed using TiO2 photocatalyst under UV illumination in an atmosphere with NO, O-2 and water vapor at 150 degrees C. Carbon is oxidized mainly to CO2 while NO is selectively converted to N-2. Enhanced O-2 and NO concentrations have a positive effect on the carbon oxidation rate. At a concentration of 3000 ppm NO and 13.3% O-2 in the gas phase the carbon oxidation rate reaches 2.3 mu g(carbon)/mg(TiO2) h, at a formal electron/photon quantum efficiency of 0.019. HR SEM images reveal uniform gradual reduction of the carbon particle size irrespective of the distance to TiO2 photocatalyst particles in the presence of NO, O-2 and H2O. (C) 2016 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 9.446
Times cited: 11
DOI: 10.1016/J.APCATB.2016.09.042
|
|
|
“Photocatalytic carbon oxidation with nitric oxide”. Liao L, Heylen S, Vallaey B, Keulemans M, Lenaerts S, Roeffaers MBJ, Martens JA, Applied catalysis : B : environmental 166, 374 (2015). http://doi.org/10.1016/J.APCATB.2014.11.051
Abstract: The photocatalytic oxidation of carbon black on TiO2 using nitric oxide as an oxidizing agent was investigated. Layer-wise deposited carbon and TiO2 powder was illuminated with UVA light in the presence of NO at parts per million concentrations in dry and hydrated carrier gas at a temperature of 150 degrees C. Carbon was photocatalytically converted mainly into CO2, and NO mainly into N-2. Carbon oxidation rates of 7.2 mu g/h/mgTiO(2) were achieved in the presence of 3000 ppm NO. Under these experimental conditions in the absence of molecular oxygen, formation of surface nitrates causing TiO2 photocatalyst deactivation is suppressed. Addition of water enhances surface nitrate formation and catalyst deactivation. NO and carbon particulate matter are air pollutants emitted by diesel engines. Elimination of soot collected on a diesel particulate filter through oxidation is a demanding reaction requiring temperatures in excess of 250 degrees C. The present study opens perspectives for a low-temperature regeneration strategy for the diesel particulate filter that simultaneously performs DeNO(x) reactions. (C) 2014 Elsevier B.V. All rights reserved.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 9.446
Times cited: 5
DOI: 10.1016/J.APCATB.2014.11.051
|
|
|
“Plasmonic goldsilver alloy on TiO2 photocatalysts with tunable visible light activity”. Verbruggen SW, Keulemans M, Filippousi M, Flahaut D, Van Tendeloo G, Lacombe S, Martens JA, Lenaerts S, Applied catalysis : B : environmental 156, 116 (2014). http://doi.org/10.1016/j.apcatb.2014.03.027
Abstract: Adaptation of the photoresponse of anatase TiO2 to match the solar spectrum is an important scientific challenge. Modification of TiO2 with noble metal nanoparticles displaying surface plasmon resonance effects is one of the promising approaches. Surface plasmon resonance typically depends on chemical composition, size, shape and spatial organization of the metal nanoparticles in contact with TiO2. AuxAg(1 − x) alloy nanoparticles display strong composition-dependent surface plasmon resonance in the visible light region of the spectrum. In this work, a general strategy is presented to prepare plasmonic TiO2-based photocatalysts with a visible light response that can be accurately tuned over a broad range of the spectrum. The application as self-cleaning material toward the degradation of stearic acid is demonstrated for a plasmonic TiO2 photocatalyst displaying visible light photoactivity at the intensity maximum of solar light around 490 nm.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT); Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 9.446
Times cited: 84
DOI: 10.1016/j.apcatb.2014.03.027
|
|
|
“Elucidating the photocatalytic degradation pathway of acetaldehyde : an FTIR in situ study under atmospheric conditions”. Hauchecorne B, Terrens D, Verbruggen S, Martens JA, van Langenhove H, Demeestere K, Lenaerts S, Applied catalysis : B : environmental 106, 630 (2011). http://doi.org/10.1016/J.APCATB.2011.06.026
Abstract: In this paper, new insights of the photocatalytic oxidation pathway of acetaldehyde are obtained by means of an in-house constructed FTIR in situ reactor. It is shown that there are generally three different intermediates present: acetic acid, formic acid and formaldehyde. By means of FTIR in situ spectroscopy, this study revealed that these intermediates are bound on the TiO2 surface in different ways, resulting in the presence of more intermediate species, such as molecularly adsorbed acetic acid, bidentate acetate, molecularly adsorbed formic acid, monodentate formate, bidentate formate, formaldehyde and dioxymethylene. Furthermore, spectroscopic evidence is obtained concerning the formation of 3-hydroxybutanal and crotonaldehyde upon adsorption of acetaldehyde on TiO2 prior to UV illumination. The presented results thus give new insights in the photocatalytic oxidation pathway of acetaldehyde.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 9.446
Times cited: 46
DOI: 10.1016/J.APCATB.2011.06.026
|
|
|
“Photocatalytic degradation of ethylene : an FTIR in situ study under atmospheric conditions”. Hauchecorne B, Tytgat T, Verbruggen SW, Hauchecorne D, Terrens D, Smits M, Vinken K, Lenaerts S, Applied catalysis : B : environmental 105, 111 (2011). http://doi.org/10.1016/J.APCATB.2011.03.041
Abstract: In this paper, the reaction mechanism of the photocatalytic oxidation of ethylene is elucidated by means of an in-house developed FTIR in situ reactor. This reactor allowed us to look at the catalytic surface at the moment the reactions actually occur. This new approach gave some exciting new insights in how ethylene is photocatalytically oxidised. It was found that there is a change in dipole moment of the ethylene molecule when it is brought in the neighbourhood of the catalyst. From this finding, a hypothesis was formulated on how the CC-bond from ethylene will break. It was found that the aforementioned interaction between the catalyst and the molecule, allows the excited electrons from the UV irradiated catalyst to occupy the lowest unoccupied molecular orbital (LUMO) of the ethylene molecule through a process known as backdonation. Following this hypothesis, it was found that the degradation occurs through the formation of two intermediates: formaldehyde and formic acid, for which formaldehyde is bound in two different ways (coordinatively and as bidentate). Finally CO2 and H2O are found as end products, resulting in the complete mineralisation of the pollutant.
Keywords: A1 Journal article; Engineering sciences. Technology; Molecular Spectroscopy (MolSpec); Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 9.446
Times cited: 29
DOI: 10.1016/J.APCATB.2011.03.041
|
|
|
“A core-shell confined Pd@TS-1 @meso-SiO2 catalyst and its synergy effect on styrene oxidation”. Wang Y-T, Wu S-M, Luo G-Q, Tian G, Wang L-Y, Xiao S-T, Wu J-X, Wu A, Wu K-J, Lenaerts S, Yang X-Y, Applied catalysis : A : general 650, 119016 (2023). http://doi.org/10.1016/J.APCATA.2022.119016
Abstract: Dual active sites from acidic zeolite and Pd are not only capable of catalyzing multiple type of reactions, but could also generate unique functions owing to the synergy between metals and acidic sites. However, there are only a few reports on the investigation of the synergy of acid/Pd dual sites in TS-1. Herein, TS-1 confined Pd catalyst with mesoporous silica shell (Pd@TS-1 @meso-SiO2) has been successfully synthesized and its synergy effect contributes to the enhanced conversion rate (19.2%) and selectivity (74.7%) on styrene oxidation. The interaction between Pd and TS-1 has been investigated by EPR and 1H NMR techniques, the experimental measurements show an obvious change in the signal distribution of weakly acidic terminal hydroxyls and hydrogen-bonding silanols. The schematic illustration of selective styrene oxidation in the model of Pd@TS-1 @meso-SiO2 is proposed to clarify the synergistic effect on styrene oxidation between TS-1 and Pd nanoparticles at an atomic-/nanoscale.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 5.5
DOI: 10.1016/J.APCATA.2022.119016
|
|
|
“Combining medium recirculation with alternating the microalga production strain : a laboratory and pilot scale cultivation test”. Fret J, Roef L, Diels L, Tavernier S, Vyverman W, Michiels M, Algal Research-Biomass Biofuels And Bioproducts 46, 101763 (2020). http://doi.org/10.1016/J.ALGAL.2019.101763
Abstract: Reuse of growth medium after biomass harvesting is a cost-saving approach to improve the economic feasibility of algae mass cultivation. Algal exudates, cell debris and varying amounts of residual nutrients, impose challenges to the recycling of spent medium. In this study, the potential of combining reused medium from different algae species for growing monocultures of other algal strains was evaluated by making use of three successive cultivation setups with increasing volume; 400 mL in turbidostat mode, 2.6 L and 220 L in semi-continuous mode. Cultivation on replenished medium derived from Nannochloropsis sp. and Tisochrysis lutea, had no adverse effect on the productivity of either of the strains, regardless of whether they were grown in their own recycled medium or that of the other alga. Microfiltration of the reused medium proved to be sufficient to avoid cross-contamination. Moreover, a substantial average reduction in water footprint (77%) and nutrient cost (68% or 9 (sic).kg(-1) dry biomass) was achieved. Extension and validation of the medium recycling approach to other economically interesting algae species can contribute to improving the economic feasibility of large scale microalgae production systems.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL); Intelligence in PRocesses, Advanced Catalysts and Solvents (iPRACS)
Impact Factor: 5.1
Times cited: 4
DOI: 10.1016/J.ALGAL.2019.101763
|
|
|
“Stoichiometry design in hierarchical CoNiFe phosphide for highly efficient water oxidation”. Chen J, Ying J, Xiao Y, Dong Y, Ozoemena K I, Lenaerts S, Yang X, Science China : materials 65, 2685 (2022). http://doi.org/10.1007/S40843-022-2061-X
Abstract: Rational composition design of trimetallic phosphide catalysts is of significant importance for enhanced surface reaction and efficient catalytic performance. Herein, hierarchical CoxNiyFezP with precise control of stoichiometric metallic elements (x:y:z = (1-10):(1-10):1) has been synthesized, and Co1.3Ni0.5Fe0.2P, as the most optimal composition, exhibits remarkable catalytic activity (eta = 320 mV at 10 mA cm(-2)) and long-term stability (ignorable decrease after 10 h continuous test at the current density of 10 mA cm(-2)) toward oxygen evolution reaction (OER). It is found that the surface P in Co1.3Ni0.5Fe0.2P was replaced by 0 under the OER process. The density function theory calculations before and after long-term stability tests suggest the clear increasing of the density of states near the Fermi level of Co1.3Ni0.5Fe0.2P/ Co1.3Ni0.5Fe0.2O, which could enhance the OH- adsorption of our electrocatalysts and the corresponding OER performance.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 8.1
DOI: 10.1007/S40843-022-2061-X
|
|
|
“Revisiting dry deposition modelling of particulate matter on vegetation at the microscale”. Ysebaert T, Samson R, Denys S, Air quality, atmosphere &, health (2023). http://doi.org/10.1007/S11869-023-01473-3
Abstract: Dry deposition is an important process determining pollutant concentrations, especially when studying the influence of urban green infrastructure on particulate matter (PM) levels in cities. Computational fluid dynamics (CFD) models of PM capture by vegetation are useful tools to increase their applicability. The meso-scale models of Zhang et al. (Atmos Environ 35:549-560, 2001) and Petroff and Zhang (Geosci Model Dev 3(2):753-769, 2010) have often been adopted in CFD models, however a comparison of these models with measurements including all PM particle sizes detrimental to health has been rarely reported and certainly not for green wall species. This study presents dry deposition experiments on real grown Hedera helix in a wind tunnel setup with wind speeds from 1 to 4 m s(-1) and PM consisting of a mixture of soot (0.02 – 0.2 mu mu m) and dust particles (0.3 – 10 mu mu m). Significant factors determining the collection efficiency (%) were particle diameter and wind speed, but relative air humidity and the type of PM (soot or dust) did not have a significant influence. Zhang's model outperformed Petroff's model for particles < 0.3 mu mu m, however the inclusion of turbulent impaction in Petroff's model resulted in better agreement with the measurements for particles > 2 – 3 mu mu m. The optimised model had an overall root-mean-square-error of similar to 4% for collection efficiency (CE) and 0.4 cm s-1 for deposition velocity (nu d), which was shown to be highly competitive against previously described models. It can thus be used to model PM deposition on other plant species, provided the correct parameterisation of the drag by this species. A detailed description of the spatial distribution of the vegetation could solve the underestimation for particle sizes of 0.3 – 2 mu mu m.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 5.1
DOI: 10.1007/S11869-023-01473-3
|
|
|
“Photothermal heating of Au nanorods and nanospheres : temperature characteristics and strength of convective forces”. Borah R, Kumar A, Samantaray M, Desai A, Tseng F-G, Plasmonics 18, 1449 (2023). http://doi.org/10.1007/S11468-023-01855-4
Abstract: The nanoscale photothermal effect and the optofluidic convection around plasmonic nanoparticles drive the application of such nanoparticles in micro-environment. In this work, heat transfer and fluid flow around Au nanospheres and nanorods in water medium under continuous and pulsed wave laser irradiance was investigated using an FEM based numerical framework. Au nanospheres of a wide range of diameter: 40 nm = Diameter (D) = 180 nm and relatively large nanorods (diameter: 50 nm) with varying aspect ratio (1 = Aspect ratio (A) = 5) and orientation (0 degrees = ? = 90 degrees, ? = 0 degrees, 90 degrees) with respect to the incident EM radiation were investigated for continuous wave (CW) and pulsed wave laser. It was found that although nanorods can attain much higher temperature than nanospheres, orientation of a nanorod is an important factor to be carefully considered in applications. In micro-scale spherical and hemispherical confinements (diameter < 14.4 p.m), the convective velocity fields around nanoparticles is in the order of 10-9 m/s, with only a weak effect of the slip or no-slip boundary condition on the confining walls. Importantly, the size of the confinement has a strong effect leading to an order of magnitude stronger convection for 14.4 p.m (diameter) spherical confinement as compared to 3.6 p.m confinement. Additionally close proximity of the nanoparticles to the confining walls strongly reduces (by an order of magnitude) the convective currents. The results reported herein provides important insights for the use of photothermal nanoparticles in microscale confined space (e.g. cellular environment) for applications such as optical tweezers, photoporation, etc.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 3
DOI: 10.1007/S11468-023-01855-4
|
|
|
“Impact of carrier on ammonia and organics removal from zero-discharge marine recirculating aquaculture system with sequencing batch biofilm reactor (SBBR)”. Li J, Zhu W, Dong H, Yang Z, Zhang P, Qiang Z, Environmental Science And Pollution Research 27, 34614 (2020). http://doi.org/10.1007/S11356-019-04887-8
Abstract: Marine recirculating aquaculture system (MRAS) is an effective technology that provides sustainable farming of food fish globally. However, dissolved organics material (chemical oxygen demand, COD) and especially ammonia are produced from uneaten feed and metabolic wastes of fish. To purify the MRAS water, this study adopted a sequencing biofilm batch reactor (SBBR) and comparatively investigated the performances of four different carriers on ammonia and COD removal. Results indicated that the NH4+-N removal rates were 0.045 +/- 0.05, 0.065 +/- 0.008, 0.089 +/- 0.005, and 0.093 +/- 0.003 kg/(m(3)center dot d), and the COD removal rates were 0.019 +/- 0.010, 0.213 +/- 0.010, 0.255 +/- 0.015, and 0.322 +/- 0.010 kg/(m(3)center dot d) in the SBBRs packed with porous plastic, bamboo ring, maifan stone, and ceramsite carriers, respectively. Among the four carriers, ceramsite exhibited the best performance for both NH4+-N (80%) and COD (33%) removal after the SBBR reached the steady-state operation conditions. For all carriers studied, the NH4+-N removal kinetics could be well simulated by the first-order model, and the NH4+-N and COD removal rates were logarithmically correlated with the carrier's specific surface area. Due to its high ammonia removal, stable performance and easy operation, the ceramsite-packed SBBR is feasible for MRAS water treatment.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 5.8
Times cited: 1
DOI: 10.1007/S11356-019-04887-8
|
|
|
“Field demonstration and evaluation of the passive flux meter on a CAH groundwater plume”. Verreydt G, Annable MD, Kaskassian S, van Keer I, Bronders J, Diels L, Vanderauwera P, Environmental Science and Pollution Research 20, 4621 (2013). http://doi.org/10.1007/S11356-012-1417-8
Abstract: This study comprises the first application of the Passive Flux Meter (PFM) for the measurement of chlorinated aliphatic hydrocarbon (CAH) mass fluxes and Darcy water fluxes in groundwater at a European field site. The PFM was originally developed and applied to measurements near source zones. The focus of the PFM is extended from near source to plume zones. For this purpose, 48 PFMs of 1.4 m length were constructed and installed in eight different monitoring wells in the source and plume zone of a CAH-contaminated field site located in France. The PFMs were retrieved, sampled, and analyzed after 3 to 11 weeks of exposure time, depending on the expected contaminant flux. PFM evaluation criteria include analytical, technical, and practical aspects as well as conditions and applicability. PFM flux data were compared with so-called traditional soil and groundwater concentration data obtained using active sampling methods. The PFMs deliver reasonable results for source as well as plume zones. The limiting factor in the PFM applicability is the exposure time together with the groundwater flux. Measured groundwater velocities at the field site range from 2 to 41 cm/day. Measured contaminant flux data raise up to 13 g/m(2)/day for perchloroethylene in the plume zone. Calculated PFM flux averaged concentration data and traditional concentration data were of similar magnitude for most wells. However, both datasets need to be compared with reservation because of the different sampling nature and time. Two important issues are the PFM tracer loss during installation/extraction and the deviation of the groundwater flow field when passing the monitoring well and PFM. The demonstration of the PFM at a CAH-contaminated field site in Europe confirmed the efficiency of the flux measurement technique for source as well as plume zones. The PFM can be applied without concerns in monitoring wells with European standards. The acquired flux data are of great value for the purpose of site characterization and mass discharge modeling, and can be used in combination with traditional soil and groundwater sampling methods.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL); Biochemical Wastewater Valorization & Engineering (BioWaVE)
DOI: 10.1007/S11356-012-1417-8
|
|
|
“Some properties of “bulky&rdquo, links, generated by Generalized Möbius Listing's bodies GML4n”. Caratelli D, Gielis J, Ricci PE, Tavkhelidze I, Journal of mathematical sciences 216, 509 (2016). http://doi.org/10.1007/S10958-016-2907-X
Abstract: In the present paper, we consider the bulky knots and bulky links that appear after cutting of generalized MöbiusListing GML 4 n bodies (with corresponding radial cross sections square) along different generalized MöbiusListing surfaces GML 2 n situated in it. The aim of this article is to examine the number and geometric structure of independent objects that appear after such a cutting process of GML 4 n bodies. In most cases, we are able to count the indices of the resulting mathematical objects according to the known tabulation for knots and links of small complexity.
Keywords: A2 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1007/S10958-016-2907-X
|
|
|
“About “bulky&rdquo, links generated by generalized Möbius-Listing bodies GML2n”. Gielis J, Tavkhelidze I, Ricci PE, Journal of mathematical sciences 193, 449 (2013). http://doi.org/10.1007/S10958-013-1474-7
Abstract: In this paper, we consider the bulky knots and bulky links, which appear after cutting of a Generalized MöbiusListing GMLn2 body (with the radial cross section a convex plane 2-symmetric figure with two vertices) along a different Generalized MöbiusListing surfaces GMLn2 situated in it. The aim of this report is to investigate the number and geometric structure of the independent objects that appear after such a cutting process of GMLn2 bodies. In most cases we are able to count the indices of the resulting mathematical objects according to the known classification for the standard knots and links.
Keywords: A2 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1007/S10958-013-1474-7
|
|
|
“Assessment of corrosion resistance, material properties, and weldability of alloyed steel for ballast tanks”. De Baere K, Verstraelen H, Willemen R, Smet J-P, Tchuindjang JT, Lecomte-Beckers J, Lenaerts S, Meskens R, Jung HG, Potters G, Journal of marine science and technology 22, 176 (2017). http://doi.org/10.1007/S00773-016-0402-1
Abstract: Ballast tanks are of great importance in the lifetime of modern merchant ships. Making a ballast tank less susceptible to corrosion can, therefore, prolong the useful life of a ship and, thereby, lower its operational cost. An option to reinforce a ballast tank is to construct it out of a corrosion-resistant steel type. Such steel was recently produced by POSCO Ltd., South Korea. After 6 months of permanent immersion, the average corrosion rate of A and AH steel (31 samples) was 535 g m(-2) year(-1), while the Korean CRS was corroding with 378 g m(-2) year(-1). This entails a gain of 29 %. Follow-up measurements after 10, 20, and 24 months confirmed this. The results after 6 months exposure to alternating wet/dry conditions are even more explicit. Furthermore, the physical and metallurgical properties of this steel show a density of 7.646 t/m(3), the elasticity modulus 209.3 GPa, the tensile strength 572 MPa, and the hardness 169HV10. Microscopically, the metal consists of equiaxed and recrystallized grains (ferrite and pearlite), with an average size of between 20 and 30 A mu m (ASTM E 112-12 grain size number between 7 and 8) with a few elongated pearlitic grains. The structure is banded ferrite/pearlite. On the basis of a series of energy dispersive X-ray spectrometer measurements the lower corrosion rate of the steel can be attributed to the interplay of Al, Cr, their oxides, and the corroding steel. In addition, the role of each element in the formation of oxide layers and the mechanisms contributing to the corrosion resistance are discussed.
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 0.838
Times cited: 3
DOI: 10.1007/S00773-016-0402-1
|
|
|
“A field study of the effectiveness of sacrificial anodes in ballast tanks of merchant ships”. De Baere K, Verstraelen H, Lemmens L, Lenaerts S, Dewil R, Van Ingelgem Y, Potters G, Journal of marine science and technology 19, 116 (2014). http://doi.org/10.1007/S00773-013-0232-3
Abstract: Sacrificial anodes have become a standard practice for the protection of ballast tanks of merchant vessels against corrosive damage. A well protected tank should extend the life span of a ship and consequently enhances its economic value. An in situ survey comprising more than 100 merchant vessels provided the opportunity to measure the impact of these anodes on the life expectancy of these vessels. Contrary to the general belief of these anodes beneficial effect, no significant difference was found in our observations in terms of corrosion occurrence between ship populations with and without sacrificial anodes, across all ship ages. This may be explained by the highly variable conditions and the complex geometry in a ballast tank severely impede optimal and straightforward installation of these anodes in these tanks. Also, poorly placed anodes in it may harm the integrity of the coating of the tank. We therefore plead for uniform and clear rules on anode installation and inspection.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
Impact Factor: 0.838
Times cited: 3
DOI: 10.1007/S00773-013-0232-3
|
|
|
“Deammonification for digester supernatant pretreated with thermal hydrolysis : overcoming inhibition through process optimization”. Zhang Q, De Clippeleir H, Su C, Al-Omari A, Wett B, Vlaeminck SE, Murthy S, Applied microbiology and biotechnology 100, 5595 (2016). http://doi.org/10.1007/S00253-016-7368-0
Abstract: The thermal hydrolysis process (THP) has been proven to be an excellent pretreatment step for an anaerobic digester (AD), increasing biogas yield and decreasing sludge disposal. The goal of this work was to optimize deammonification for efficient nitrogen removal despite the inhibition effects caused by the organics present in the THP-AD sludge filtrate (digestate). Two sequencing batch reactors were studied treating conventional digestate and THP-AD digestate, respectively. Improved process control based on higher dissolved oxygen set-point (1 mg O-2/L) and longer aeration times could achieve successful treatment of THP-AD digestate. This increased set-point could overcome the inhibition effect on aerobic ammonium-oxidizing bacteria (AerAOB), potentially caused by particulate and colloidal organics. Moreover, based on the mass balance, anoxic ammonium-oxidizing bacteria (AnAOB) contribution to the total nitrogen removal decreased from 97 +/- A 1 % for conventional to 72 +/- A 5 % for THP-AD digestate treatment, but remained stable by selective AnAOB retention using a vibrating screen. Overall, similar total nitrogen removal rates of 520 +/- A 28 mg N/L/day at a loading rate of 600 mg N/L/day were achieved in the THP-AD reactor compared to the conventional digestate treatment operating at low dissolved oxygen (DO) (0.38 +/- A 0.10 mg O-2/L).
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1007/S00253-016-7368-0
|
|
|
“Correlations between molecular and operational parameters in continuous lab-scale anaerobic reactors”. Carballa M, Smits M, Etchebehere C, Boon N, Verstraete W, Applied microbiology and biotechnology 89, 303 (2011). http://doi.org/10.1007/S00253-010-2858-Y
Abstract: In this study, the microbial community characteristics in continuous lab-scale anaerobic reactors were correlated to reactor functionality using the microbial resource management (MRM) approach. Two molecular techniques, denaturing gradient gel electrophoresis (DGGE) and terminal-restriction fragment length polymorphism (T-RFLP), were applied to analyze the bacterial and archaeal communities, and the results obtained have been compared. Clustering analyses showed a similar discrimination of samples with DGGE and T-RFLP data, with a clear separation between the meso- and thermophilic communities. Both techniques indicate that bacterial and mesophilic communities were richer and more even than archaeal and thermophilic communities, respectively. Remarkably, the community composition was highly dynamic for both Bacteria and Archaea, with a rate of change between 30% and 75% per 18 days, also in stable performing periods. A hypothesis to explain the latter in the context of the converging metabolism in anaerobic processes is proposed. Finally, a more even and diverse bacterial community was found to be statistically representative for a well-functioning reactor as evidenced by a low Ripley index and high biogas production.
Keywords: A1 Journal article; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1007/S00253-010-2858-Y
|
|
|
“The common descent of biological shape description and special functions”. Gielis J, Caratelli D, de Jong van Coevorden M, Ricci PE page 119 (2018).
Abstract: Gielis transformations, with their origin in botany, are used to define square waves and trigonometric functions of higher order. They are rewritten in terms of Chebyshev polynomials. The origin of both, a uniform descriptor and the origin of orthogonal polynomials, can be traced back to a letter of Guido Grandi to Leibniz in 1713 on the mathematical description of the shape of flowers. In this way geometrical description and analytical tools are seamlessly combined.
Keywords: H1 Book chapter; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1007/978-3-319-75647-9_10
|
|
|
“Short and long term effect of decreasing temperature on anammox activity and enrichment in mainstream granular sludge process”. De Cocker P, Bessiere Y, Hernandez-Raquet G, Dubos S, Mercade M, Sun XY, Mozo I, Barillon B, Gaval G, Caligaris M, Martin Ruel S, Vlaeminck SE, Sperandio M, 4, 50 (2017). http://doi.org/10.1007/978-3-319-58421-8_8
Abstract: This study investigates the impact of lower temperature on short term and long term (down to 10 degrees C) on a completely anoxic anammox granular sludge process. This is the first time granular sludge Anammox is operated in pure anoxic condition in SBR and at low temperature. Conversion performance, kinetic parameters, sludge characteristics and microbial community were analyzed.
Keywords: P1 Proceeding; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1007/978-3-319-58421-8_8
|
|
|
“Short and long term effect of decreasing temperature on anammox activity and enrichment in mainstream granular sludge process”. De Cocker P, Bessiere Y, Hernandez-Raquet G, Dubos S, Mercade M, Sun XY, Mozo I, Barillon B, Gaval G, Caligaris M, Ruel SM, Vlaeminck SE, Sperandio M, Frontiers In Wastewater Treatment And Modelling, Ficwtm 2017 4, 50 (2017). http://doi.org/10.1007/978-3-319-58421-8_8
Abstract: This study investigates the impact of lower temperature on short term and long term (down to 10 degrees C) on a completely anoxic anammox granular sludge process. This is the first time granular sludge Anammox is operated in pure anoxic condition in SBR and at low temperature. Conversion performance, kinetic parameters, sludge characteristics and microbial community were analyzed.
Keywords: P1 Proceeding; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1007/978-3-319-58421-8_8
|
|
|
“Lab-scale physical model experiments to understand the effect of particle bed on tapping flow rates”. Loomba V, Pourfallah H, Olsen JE, Einarsrud KE, , 159 (2022). http://doi.org/10.1007/978-3-030-92544-4_13
Keywords: P1 Proceeding; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1007/978-3-030-92544-4_13
|
|
|
“The general case of cutting GML bodies : the geometrical solution”. Gielis J, Caratelli D, Tavkhelidze I page 397 (2020).
Keywords: H1 Book chapter; Engineering sciences. Technology; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1007/978-3-030-56323-3_31
|
|
|
“About some methods of analytic representation and classification of a wide set of geometric figures with “complex” configuration”. Tavkhelidze I, Gielis J, Pinelas S page 347 (2020).
Keywords: H1 Book chapter; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1007/978-3-030-56323-3_27
|
|
|
“Immunoreactivity for p53 protein in malignant mesothelioma and non-neoplastic mesothelium”. Ramael M, Lemmens G, Eerdekens C, Buysse C, Deblier I, Jacobs W, Van Marck E, The journal of pathology 168, 371 (1992). http://doi.org/10.1002/PATH.1711680406
Keywords: A1 Journal article; Sustainable Energy, Air and Water Technology (DuEL)
DOI: 10.1002/PATH.1711680406
|
|