|
“Structural characterisation of erbium silicide thin films of an Si(111) substrate”. Frangis N, Van Tendeloo G, van Landuyt J, Muret P, Nguyen TTA, Journal of alloys and compounds 234, 244 (1996). http://doi.org/10.1016/0925-8388(95)02131-0
Abstract: ErSi2-x films (x = 0.1-0.3) grown by co-evaporation at different deposition ratios have been characterised by transmission electron microscopy, electron diffraction and high resolution electron microscopy. A very good epitaxial growth relation with the Si substrate was deduced for a1 samples and observed phases. Different defect modulated structures are formed; they can be described as structural variants (orthorhombic or rhombohedral) of the basic structure. The modulated phases are related to deviations from stoichiometry similar to crystallographic shear structures. The ErSi1.9 material contains Si precipitates, illustrating the preference for the ErSi1.7 composition to be maintained.
Keywords: A1 Journal article; Engineering sciences. Technology; Electron microscopy for materials research (EMAT)
Impact Factor: 2.999
Times cited: 14
DOI: 10.1016/0925-8388(95)02131-0
|
|
“The study of a crater forming on the surface of a Ti target submitted to multipulse excimer laser irradiation under low pressure N2”. Teodorescu VS, Mihailescu IN, Gyorgy E, Luches A, Martino M, Nistor LC, van Landuyt J, Hermann J, Journal of modern optics 43, 1773 (1996). http://doi.org/10.1080/095003496154815
Abstract: A Ti target was submitted to laser ablation in low ambient pressure N-2. Electron microscopy examination of the cross-section of the crater zone forming on the Ti target, and XPS analyses, indicate that there is a small effect on the nitridation processes taking place on and in the vicinity of the target. The studies show a zone influenced by the multipulse laser treatment extending beneath the crater down to a depth of the same order of magnitude as the crater depth (i.e. similar to 10 mu m). In this zone, TiN could be identified as being present only in traces, while the whole zone exhibited a layer structure with differences in morphology and mechanical wear.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.008
Times cited: 11
DOI: 10.1080/095003496154815
|
|
“Characterization of LPE grown InGaAsP/InP heterostructures: IR-LED at 1.66 μm used for the remote monitoring of methane gas”. Volkov VV, van Landuyt J, Marushkin KM, Gijbels R, Férauge C, Vasilyev MG, Shelyakin AA, Sokolovsky AA, Journal of crystal growth 173, 285 (1997)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 1.751
Times cited: 4
|
|
“Computational comparisons between the conventional multislice method and the third-order multislice method for calculating high-energy electron diffraction and imaging”. Chen JH, van Dyck D, op de Beeck M, van Landuyt J, Ultramicroscopy 69, 219 (1997)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT); Vision lab
Impact Factor: 2.843
Times cited: 11
|
|
“Defect characterization in high temperature implanted 6H-SiC using TEM”. Suvorov AV, Lebedev OI, Suvorova AA, van Landuyt J, Usov IO, Nuclear instruments and methods in physics research: B 127/128, 347 (1997). http://doi.org/10.1016/S0168-583X(96)00954-8
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.109
Times cited: 17
DOI: 10.1016/S0168-583X(96)00954-8
|
|
“Electron microscopical investigation of tetrahedral-shaped AgBr microcrystals”. Goessens C, Schryvers D, van Landuyt J, de Keyzer R, Journal of crystal growth 172, 426 (1997)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.751
Times cited: 15
|
|
“Electron microscopy of carbon nanotubes and related structures”. Bernaerts D, Amelinckx S, Van Tendeloo G, van Landuyt J, The journal of physics and chemistry of solids 58, 1807 (1997). http://doi.org/10.1016/S0022-3697(98)80003-6
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.059
Times cited: 12
DOI: 10.1016/S0022-3697(98)80003-6
|
|
Amelinckx S, van Dyck D, van Landuyt J, Van Tendeloo G (1997) Electron microscopy: principles and fundamentals. Vch, Weinheim
Keywords: ME1 Book as editor or co-editor; Electron microscopy for materials research (EMAT); Vision lab
|
|
“The formation of 3C-SiC in crystalline Si by carbon implantation at 9500C and annealing: a structural study”. Frangis N, Stoemenos J, van Landuyt J, Nejim A, Hemment PLF, Journal of crystal growth 181, 218 (1997)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.751
Times cited: 9
|
|
“Growth of erbium-silicide films on (100) silicon as characterised by electron microscopy and diffraction”. Frangis N, van Landuyt J, Kaltsas G, Travlos A, Nassiopoulos AG, Journal of crystal growth 172, 175 (1997)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.751
Times cited: 29
|
|
Amelinckx S, van Dyck D, van Landuyt J, Van Tendeloo G (1997) Handbook of microscopy: applications in materials science, solid-state physics and chemistry. Vch, Weinheim
Keywords: ME1 Book as editor or co-editor; Electron microscopy for materials research (EMAT); Vision lab
|
|
“High resolution TEM observation of in situ colloid formation in CaF2 crystals”. Teodorescu VS, Nistor LC, van Landuyt J, Materials science forum 239-241, 671 (1997)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 3
|
|
“HREM image analysis up to structure determination of SbCrSe3: a new 1D ferromagnet”. Volkov VV, Van Tendeloo G, van Landuyt J, Amelinckx S, Busheva EE, Shabunina GG, Aminov TG, Novotortsev VM, Journal of solid state chemistry 132, 257 (1997)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.299
Times cited: 1
|
|
“In-situ HREM irradiation study of point defect clustering in strained GexSi1-x/(001)Si heterostructure”. Fedina L, Lebedev OI, Van Tendeloo G, van Landuyt J, Conference series of the Institute of Physics 157, 55 (1997)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Times cited: 1
|
|
“Intrinsic point defect clustering in Si: a study by HVEM and HREM in situ electron irradiation”. Fedina L, Gutakovskii A, Aseev A, van Landuyt J, Vanhellemont J Kluwer Academic, s.l., page 63 (1997).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
|
|
“LPE growth and characterization of InGaAsP/InP heterostructures: IR-emitting diodes at 1.66 μm: application to the remote monitoring of methane gas”. Volkov VV, van Landuyt J, Marushkin K, Gijbels R, Férauge C, Vasilyev MG, Shelyakin AA, Sokolovsky AA, Sensors and actuators : A : physical 62, 624 (1997). http://doi.org/10.1016/S0924-4247(97)01377-0
Abstract: Highly effective IR light-emitting diodes operating at the wavelength 1.66 mu m and based on the buried heterostructure In0.88Ga0.12As0.26P0.74/ In0.72Ga0.28As0.62P0.38/In0.53Ga0.47As/InP have been grown by liquid-phase epitaxy (LPE) and characterized in detail by means of transmission electron microscopy (TEM), high-resolution electron microscopy (HREM),electron diffraction (ED), X-ray diffraction (XRD), secondary-ion mass spectrometry (SIMS) and electroluminescence measurements. The InGaAsP epilayers are found to be well lattice matched and of good structural quality. A tentative explanation is presented for the spinodal decomposition observed in InGaAsP alloys. A new type of selective CK, gas sensor has been developed and fabricated an the basis of the IR light-emitting diode mentioned above. Especially designed for the remote control of CH4 gas via fibre optics, an integrated optoelectronic readout scheme has been developed and tested, It is shown that the proposed type of sensor can be used for the quantitative remote control of CH4 gas concentration (0.2-100%) via a fibre glass line up to a distance of 2 x 1 km. (C) 1997 Elsevier Science S.A.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT); Plasma Lab for Applications in Sustainability and Medicine – Antwerp (PLASMANT)
Impact Factor: 2.499
Times cited: 3
DOI: 10.1016/S0924-4247(97)01377-0
|
|
“Microscopy of gemmological materials”. van Landuyt J, van Bockstael MHG, van Royen J Vch, Weinheim, page 293 (1997).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
Times cited: 4
|
|
“Microstructure and formation mechanisms of cylindrical and conical scrolls of the misfit layer compounds PbNbnS2n+1”. Bernaerts D, Amelinckx S, Van Tendeloo G, van Landuyt J, Journal of crystal growth 172, 433 (1997)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.751
Times cited: 23
|
|
“Microstructure of Mn-doped, spin-cast FeSi2”. Morimura T, Frangis N, Van Tendeloo G, van Landuyt J, Hasaka M, Hisatsune K, Journal of electron microscopy 46, 221 (1997)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 0.9
Times cited: 3
|
|
“Nanocrystalline diamond films: transmission electron microscopy and Raman spectroscopy characterization”. Nistor LC, van Landuyt J, Ralchenko VG, Obratzova ED, Smolin AA, Diamond and related materials 6, 159 (1997)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.561
Times cited: 116
|
|
“New intermediate defect configuration in Si studied by in situ HREM irradiation”. Fedina L, Gutakovskii A, Aseev A, van Landuyt J, Vanhellemont J, Conference series of the Institute of Physics 157, 43 (1997)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
|
|
“New method to determine the parity of the number of twin planes in tabular silver halide microcrystals from top views”. Goessens C, Schryvers D, van Landuyt J, de Keyzer R, The journal of imaging science and technology 41, 301 (1997)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 0.348
Times cited: 1
|
|
“Structural studies of nanocrystalline diamond thin films”. Nistor LC, van Landuyt J, Ralchenko VG, Obratzova ED, Korothushenko KG, Smolin AA, Materials science forum 239-241, 115 (1997)
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
|
|
“TEM studies of processed Si device materials”. Vanhellemont J, Bender H, van Landuyt J, Conference series of the Institute of Physics 157, 393 (1997)
Abstract: Recent developments in the field of TEM characterisation of Si device materials are discussed and illustrated by a few case studies of material in different stages of various kinds of processing. Important challenges are the ever decreasing defect densities and device feature sizes. Defect delineation techniques using large area inspection tools yielding accurate coordinates of the defects to be studied have therefore become an essential part of the TEM analysis procedure. The possibility to transfer these defect coordinates without loss of accuracy to tools for local TEM specimen preparation is also a conditio sine qua non for a successful analysis. Insitu TEM remains important as dynamic processes can be observed and analysed under well defined experimental conditions. As case studies illustrating new developments, results are presented on defects in as-grown Ct silicon, on in-situ studies in processed silicon, on problem sites in advanced integrated circuit structures and on assessment of localised strain fields in the nm size scale.
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
|
|
“Charcaterization by high-resolution transmission electron microscopy”. van Landuyt J, Van Tendeloo G Stt, Den Haag, page 187 (1998).
Keywords: H3 Book chapter; Electron microscopy for materials research (EMAT)
|
|
“Conventional and HREM study of structural defects in nanostructured silver halides”. Schryvers D, Goessens C, van Renterghem W, van Landuyt J, de Keyzer R, , 1 (1998)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
“Defect related growth of tabular AgCl(100) crystals: a TEM study”. van Renterghem W, Schryvers D, van Landuyt J, van Roost C, , 389 (1998)
Keywords: P1 Proceeding; Electron microscopy for materials research (EMAT)
|
|
“Defects and growth mechanisms of AgCl(100) tabular crystals”. van Renterghem W, Goessens C, Schryvers D, van Landuyt J, Verrept P, Bollen D, van Roost C, de Keyzer R, Journal of crystal growth 187, 410 (1998). http://doi.org/10.1016/S0022-0248(98)00004-9
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 1.751
Times cited: 8
DOI: 10.1016/S0022-0248(98)00004-9
|
|
“Defects in AgCl and AgBr(100) tabular crystals studied by TEM”. van Renterghem W, Goessens C, Schryvers D, van Landuyt J, Verrept P, Bollen D, van Roost C, de Keyzer R, , 6 (1998)
Keywords: P3 Proceeding; Electron microscopy for materials research (EMAT)
|
|
“Electron microscopic and X-ray structural analysis of the layered crystals TaReSe4: structure, defect structure, and microstructure, including rotation twins”. Volkov VV, van Landuyt J, Amelinckx S, Pervov VS, Makhonina EV, Journal of solid state chemistry 135, 235 (1998). http://doi.org/10.1006/jssc.1997.7621
Keywords: A1 Journal article; Electron microscopy for materials research (EMAT)
Impact Factor: 2.299
Times cited: 3
DOI: 10.1006/jssc.1997.7621
|